493 lines
12 KiB
Text
493 lines
12 KiB
Text
|
#include <dt-bindings/msm-camera.h>
|
||
|
|
|
||
|
|
&tlmm {
|
||
|
|
cam_dvdd_front_en_default: cam_dvdd_front_en_default {
|
||
|
|
mux {
|
||
|
|
pins = "gpio0";
|
||
|
|
function = "gpio";
|
||
|
|
};
|
||
|
|
|
||
|
|
config {
|
||
|
|
pins = "gpio0";
|
||
|
|
bias-pull-down; /* PULL DOWN */
|
||
|
|
drive-strength = <2>; /* 2 MA */
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
cam_afvdd_front_en_default: cam_afvdd_front_en_default {
|
||
|
|
mux {
|
||
|
|
pins = "gpio7";
|
||
|
|
function = "gpio";
|
||
|
|
};
|
||
|
|
|
||
|
|
config {
|
||
|
|
pins = "gpio7";
|
||
|
|
bias-pull-down; /* PULL DOWN */
|
||
|
|
drive-strength = <2>; /* 2 MA */
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
cam_dvdd_uw_en_default: cam_dvdd_uw_en_default {
|
||
|
|
mux {
|
||
|
|
pins = "gpio73";
|
||
|
|
function = "gpio";
|
||
|
|
};
|
||
|
|
|
||
|
|
config {
|
||
|
|
pins = "gpio73";
|
||
|
|
bias-pull-down; /* PULL DOWN */
|
||
|
|
drive-strength = <2>; /* 2 MA */
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
cam_ois_af_vdd_tele_en_default: cam_ois_af_vdd_tele_en_default {
|
||
|
|
mux {
|
||
|
|
pins = "gpio4";
|
||
|
|
function = "gpio";
|
||
|
|
};
|
||
|
|
|
||
|
|
config {
|
||
|
|
pins = "gpio4";
|
||
|
|
bias-pull-down; /* PULL DOWN */
|
||
|
|
drive-strength = <2>; /* 2 MA */
|
||
|
|
};
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
&L16B {
|
||
|
|
regulator-min-microvolt = <3300000>;
|
||
|
|
regulator-max-microvolt = <3300000>;
|
||
|
|
qcom,init-voltage = <3300000>;
|
||
|
|
};
|
||
|
|
|
||
|
|
&L8B {
|
||
|
|
regulator-min-microvolt = <2800000>;
|
||
|
|
regulator-max-microvolt = <2800000>;
|
||
|
|
qcom,init-voltage = <2800000>;
|
||
|
|
};
|
||
|
|
|
||
|
|
&pm8550_flash0 {
|
||
|
|
qcom,max-current-ma = <650>;
|
||
|
|
qcom,duration-ms = <500>;
|
||
|
|
};
|
||
|
|
&pm8550_flash1 {
|
||
|
|
qcom,max-current-ma = <650>;
|
||
|
|
qcom,duration-ms = <500>;
|
||
|
|
};
|
||
|
|
&pm8550_flash2 {
|
||
|
|
qcom,duration-ms = <500>;
|
||
|
|
};
|
||
|
|
&pm8550_flash3 {
|
||
|
|
qcom,duration-ms = <500>;
|
||
|
|
};
|
||
|
|
|
||
|
|
&pm8550_torch0 {
|
||
|
|
qcom,max-current-ma = <125>;
|
||
|
|
};
|
||
|
|
|
||
|
|
&pm8550_torch1 {
|
||
|
|
qcom,max-current-ma = <125>;
|
||
|
|
};
|
||
|
|
|
||
|
|
&soc {
|
||
|
|
cam_dvdd_uw: gpio-regulator@0 {
|
||
|
|
compatible = "regulator-fixed";
|
||
|
|
reg = <0x00 0x00>;
|
||
|
|
regulator-name = "cam_dvdd_uw";
|
||
|
|
regulator-min-microvolt = <1050000>;
|
||
|
|
regulator-max-microvolt = <1050000>;
|
||
|
|
regulator-enable-ramp-delay = <233>;
|
||
|
|
enable-active-high;
|
||
|
|
gpio = <&tlmm 73 0>;
|
||
|
|
pinctrl-names = "default";
|
||
|
|
pinctrl-0 = <&cam_dvdd_uw_en_default>;
|
||
|
|
vin-supply = <&S4G>;
|
||
|
|
};
|
||
|
|
|
||
|
|
cam_dvdd_front: gpio-regulator@1 {
|
||
|
|
compatible = "regulator-fixed";
|
||
|
|
reg = <0x01 0x00>;
|
||
|
|
regulator-name = "cam_dvdd_front";
|
||
|
|
regulator-min-microvolt = <1050000>;
|
||
|
|
regulator-max-microvolt = <1050000>;
|
||
|
|
regulator-enable-ramp-delay = <233>;
|
||
|
|
enable-active-high;
|
||
|
|
gpio = <&tlmm 0 0>;
|
||
|
|
pinctrl-names = "default";
|
||
|
|
pinctrl-0 = <&cam_dvdd_front_en_default>;
|
||
|
|
vin-supply = <&S4G>;
|
||
|
|
};
|
||
|
|
|
||
|
|
cam_ois_af_vdd_tele: gpio-regulator@2 {
|
||
|
|
compatible = "regulator-fixed";
|
||
|
|
reg = <0x02 0x00>;
|
||
|
|
regulator-name = "cam_ois_af_vdd_tele";
|
||
|
|
regulator-min-microvolt = <2800000>;
|
||
|
|
regulator-max-microvolt = <2800000>;
|
||
|
|
regulator-enable-ramp-delay = <233>;
|
||
|
|
enable-active-high;
|
||
|
|
gpio = <&tlmm 4 0>;
|
||
|
|
pinctrl-names = "default";
|
||
|
|
pinctrl-0 = <&cam_ois_af_vdd_tele_en_default>;
|
||
|
|
vin-supply = <&BOB1>;
|
||
|
|
};
|
||
|
|
|
||
|
|
cam_afvdd_front: gpio-regulator@3 {
|
||
|
|
compatible = "regulator-fixed";
|
||
|
|
reg = <0x03 0x00>;
|
||
|
|
regulator-name = "cam_afvdd_front";
|
||
|
|
regulator-min-microvolt = <2800000>;
|
||
|
|
regulator-max-microvolt = <2800000>;
|
||
|
|
regulator-enable-ramp-delay = <233>;
|
||
|
|
enable-active-high;
|
||
|
|
gpio = <&tlmm 7 0>;
|
||
|
|
pinctrl-names = "default";
|
||
|
|
pinctrl-0 = <&cam_afvdd_front_en_default>;
|
||
|
|
vin-supply = <&BOB1>;
|
||
|
|
};
|
||
|
|
|
||
|
|
led_flash_rear_main: qcom,camera-flash0 {
|
||
|
|
cell-index = <0>;
|
||
|
|
compatible = "qcom,camera-flash";
|
||
|
|
flash-source = <&pm8550_flash0 &pm8550_flash1>;
|
||
|
|
torch-source = <&pm8550_torch0 &pm8550_torch1>;
|
||
|
|
switch-source = <&pm8550_switch2>;
|
||
|
|
status = "ok";
|
||
|
|
};
|
||
|
|
|
||
|
|
led_flash_rear_uw: qcom,camera-flash2 {
|
||
|
|
cell-index = <2>;
|
||
|
|
compatible = "qcom,camera-flash";
|
||
|
|
flash-source = <&pm8550_flash0 &pm8550_flash1>;
|
||
|
|
torch-source = <&pm8550_torch0 &pm8550_torch1>;
|
||
|
|
switch-source = <&pm8550_switch2>;
|
||
|
|
status = "ok";
|
||
|
|
};
|
||
|
|
|
||
|
|
led_flash_rear_tele: qcom,camera-flash3 {
|
||
|
|
cell-index = <3>;
|
||
|
|
compatible = "qcom,camera-flash";
|
||
|
|
flash-source = <&pm8550_flash0 &pm8550_flash1>;
|
||
|
|
torch-source = <&pm8550_torch0 &pm8550_torch1>;
|
||
|
|
switch-source = <&pm8550_switch2>;
|
||
|
|
status = "ok";
|
||
|
|
};
|
||
|
|
|
||
|
|
qcom,cam-res-mgr {
|
||
|
|
compatible = "qcom,cam-res-mgr";
|
||
|
|
status = "ok";
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
&cam_cci0 {
|
||
|
|
|
||
|
|
actuator_rear_main: qcom,actuator0{
|
||
|
|
cell-index = <0>;
|
||
|
|
compatible = "qcom,actuator";
|
||
|
|
cci-master = <CCI_MASTER_0>;
|
||
|
|
cam_vaf-supply = <&L16B>;
|
||
|
|
regulator-names = "cam_vaf";
|
||
|
|
rgltr-cntrl-support;
|
||
|
|
rgltr-min-voltage = <3300000>;
|
||
|
|
rgltr-max-voltage = <3300000>;
|
||
|
|
rgltr-load-current = <119000>;
|
||
|
|
status = "ok";
|
||
|
|
};
|
||
|
|
|
||
|
|
eeprom_rear_main: qcom,eeprom@0 {
|
||
|
|
cell-index = <0>;
|
||
|
|
reg = <0x0>;
|
||
|
|
compatible = "qcom,eeprom";
|
||
|
|
cci-master = <CCI_MASTER_0>;
|
||
|
|
cam_vio-supply = <&L4B>;
|
||
|
|
regulator-names = "cam_vio";
|
||
|
|
rgltr-cntrl-support;
|
||
|
|
rgltr-min-voltage = <1800000>;
|
||
|
|
rgltr-max-voltage = <1800000>;
|
||
|
|
rgltr-load-current = <0>;
|
||
|
|
status = "ok";
|
||
|
|
};
|
||
|
|
|
||
|
|
eeprom_rear_uw: qcom,eeprom@2 {
|
||
|
|
cell-index = <2>;
|
||
|
|
reg = <0x2>;
|
||
|
|
compatible = "qcom,eeprom";
|
||
|
|
cci-master = <CCI_MASTER_1>;
|
||
|
|
cam_vio-supply = <&L4B>;
|
||
|
|
regulator-names = "cam_vio";
|
||
|
|
rgltr-cntrl-support;
|
||
|
|
rgltr-min-voltage = <1800000>;
|
||
|
|
rgltr-max-voltage = <1800000>;
|
||
|
|
rgltr-load-current = <0>;
|
||
|
|
};
|
||
|
|
|
||
|
|
actuator_rear_uw: qcom,actuator2{
|
||
|
|
cell-index = <2>;
|
||
|
|
compatible = "qcom,actuator";
|
||
|
|
cci-master = <CCI_MASTER_1>;
|
||
|
|
cam_vaf-supply = <&L8B>;
|
||
|
|
regulator-names = "cam_vaf";
|
||
|
|
rgltr-cntrl-support;
|
||
|
|
rgltr-min-voltage = <2800000>;
|
||
|
|
rgltr-max-voltage = <2804000>;
|
||
|
|
rgltr-load-current = <147000>;
|
||
|
|
status = "ok";
|
||
|
|
};
|
||
|
|
|
||
|
|
rear_main: qcom,cam-sensor0 {
|
||
|
|
cell-index = <0>;
|
||
|
|
compatible = "qcom,cam-sensor";
|
||
|
|
csiphy-sd-index = <1>;
|
||
|
|
eeprom-src = <&eeprom_rear_main>;
|
||
|
|
led-flash-src = <&led_flash_rear_main>;
|
||
|
|
actuator-src = <&actuator_rear_main>;
|
||
|
|
sensor-position-roll = <90>;
|
||
|
|
sensor-position-pitch = <0>;
|
||
|
|
sensor-position-yaw = <180>;
|
||
|
|
cam_vio-supply = <&L4B>;
|
||
|
|
cam_vdig-supply = <&camera_ldo1>;
|
||
|
|
cam_clk-supply = <&cam_cc_titan_top_gdsc>;
|
||
|
|
cam_vana-supply = <&camera_ldo3>;
|
||
|
|
//cam_vaf-supply = <&L16B>;
|
||
|
|
regulator-names = "cam_vana",
|
||
|
|
"cam_vdig","cam_clk","cam_vio";
|
||
|
|
rgltr-cntrl-support;
|
||
|
|
rgltr-min-voltage = <2800000 1200000 0 1800000>;
|
||
|
|
rgltr-max-voltage = <2804000 1200000 0 1800000>;
|
||
|
|
rgltr-load-current = <101000 787000 0 1000>;
|
||
|
|
gpio-no-mux = <0>;
|
||
|
|
pinctrl-names = "cam_default", "cam_suspend";
|
||
|
|
pinctrl-0 = <&cam_sensor_mclk1_active
|
||
|
|
&cam_sensor_active_rst1>;
|
||
|
|
pinctrl-1 = <&cam_sensor_mclk1_suspend
|
||
|
|
&cam_sensor_suspend_rst1>;
|
||
|
|
gpios = <&tlmm 101 0>,
|
||
|
|
<&tlmm 117 0>;
|
||
|
|
gpio-reset = <1>;
|
||
|
|
gpio-req-tbl-num = <0 1>;
|
||
|
|
gpio-req-tbl-flags = <1 0>;
|
||
|
|
gpio-req-tbl-label = "CAMIF_MCLK1",
|
||
|
|
"CAM_RESET1";
|
||
|
|
cci-master = <CCI_MASTER_0>;
|
||
|
|
clocks = <&camcc CAM_CC_MCLK1_CLK>;
|
||
|
|
clock-names = "cam_clk";
|
||
|
|
clock-cntl-level = "nominal";
|
||
|
|
clock-rates = <19200000>;
|
||
|
|
status = "ok";
|
||
|
|
};
|
||
|
|
|
||
|
|
rear_uw:qcom,cam-sensor2 {
|
||
|
|
cell-index = <2>;
|
||
|
|
compatible = "qcom,cam-sensor";
|
||
|
|
csiphy-sd-index = <2>;
|
||
|
|
sensor-position-roll = <90>;
|
||
|
|
sensor-position-pitch = <0>;
|
||
|
|
sensor-position-yaw = <180>;
|
||
|
|
led-flash-src = <&led_flash_rear_uw>;
|
||
|
|
eeprom-src = <&eeprom_rear_uw>;
|
||
|
|
actuator-src = <&actuator_rear_uw>;
|
||
|
|
cam_vio-supply = <&L4B>;
|
||
|
|
cam_vdig-supply = <&cam_dvdd_uw>;
|
||
|
|
cam_clk-supply = <&cam_cc_titan_top_gdsc>;
|
||
|
|
cam_vana-supply = <&camera_ldo4>;
|
||
|
|
regulator-names = "cam_vana",
|
||
|
|
"cam_vdig", "cam_clk","cam_vio";
|
||
|
|
rgltr-cntrl-support;
|
||
|
|
rgltr-min-voltage = <2800000 1050000 0 1800000>;
|
||
|
|
rgltr-max-voltage = <2800000 1050000 0 1800000>;
|
||
|
|
rgltr-load-current = <148000 212000 0 3000>;
|
||
|
|
gpio-no-mux = <0>;
|
||
|
|
pinctrl-names = "cam_default", "cam_suspend";
|
||
|
|
pinctrl-0 = <&cam_sensor_mclk2_active
|
||
|
|
&cam_sensor_active_rst2>;
|
||
|
|
pinctrl-1 = <&cam_sensor_mclk2_suspend
|
||
|
|
&cam_sensor_suspend_rst2>;
|
||
|
|
gpios = <&tlmm 102 0>,
|
||
|
|
<&tlmm 118 0>;
|
||
|
|
gpio-reset = <1>;
|
||
|
|
gpio-req-tbl-num = <0 1>;
|
||
|
|
gpio-req-tbl-flags = <1 0>;
|
||
|
|
gpio-req-tbl-label = "CAMIF_MCLK2",
|
||
|
|
"CAM_RESET2";
|
||
|
|
cci-master = <CCI_MASTER_1>;
|
||
|
|
clocks = <&camcc CAM_CC_MCLK2_CLK>;
|
||
|
|
clock-names = "cam_clk";
|
||
|
|
clock-cntl-level = "nominal";
|
||
|
|
clock-rates = <24000000>;
|
||
|
|
status = "ok";
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
&cam_cci1 {
|
||
|
|
i2c_freq_100Khz_cci1: qcom,i2c_standard_mode {
|
||
|
|
hw-scl-stretch-en = <1>;
|
||
|
|
};
|
||
|
|
|
||
|
|
i2c_freq_400Khz_cci1: qcom,i2c_fast_mode {
|
||
|
|
hw-scl-stretch-en = <1>;
|
||
|
|
};
|
||
|
|
|
||
|
|
i2c_freq_custom_cci1: qcom,i2c_custom_mode {
|
||
|
|
hw-scl-stretch-en = <1>;
|
||
|
|
};
|
||
|
|
|
||
|
|
i2c_freq_1Mhz_cci1: qcom,i2c_fast_plus_mode {
|
||
|
|
hw-scl-stretch-en = <1>;
|
||
|
|
};
|
||
|
|
|
||
|
|
actuator_front: qcom,actuator1{
|
||
|
|
cell-index = <1>;
|
||
|
|
compatible = "qcom,actuator";
|
||
|
|
cci-master = <CCI_MASTER_1>;
|
||
|
|
cam_vaf-supply = <&cam_afvdd_front>;
|
||
|
|
regulator-names = "cam_vaf";
|
||
|
|
rgltr-cntrl-support;
|
||
|
|
rgltr-min-voltage = <2800000>;
|
||
|
|
rgltr-max-voltage = <2800000>;
|
||
|
|
rgltr-load-current = <95000>;
|
||
|
|
status = "ok";
|
||
|
|
};
|
||
|
|
|
||
|
|
eeprom_front: qcom,eeprom@1 {
|
||
|
|
cell-index = <1>;
|
||
|
|
compatible = "qcom,eeprom";
|
||
|
|
cci-master = <CCI_MASTER_1>;
|
||
|
|
cam_vio-supply = <&L4B>;
|
||
|
|
regulator-names = "cam_vio";
|
||
|
|
rgltr-cntrl-support;
|
||
|
|
rgltr-min-voltage = <1800000>;
|
||
|
|
rgltr-max-voltage = <1800000>;
|
||
|
|
rgltr-load-current = <3000>;
|
||
|
|
status = "ok";
|
||
|
|
};
|
||
|
|
|
||
|
|
front_main: qcom,cam-sensor1 {
|
||
|
|
cell-index = <1>;
|
||
|
|
compatible = "qcom,cam-sensor";
|
||
|
|
csiphy-sd-index = <3>;
|
||
|
|
sensor-position-roll = <270>;
|
||
|
|
sensor-position-pitch = <0>;
|
||
|
|
sensor-position-yaw = <0>;
|
||
|
|
eeprom-src = <&eeprom_front>;
|
||
|
|
actuator-src = <&actuator_front>;
|
||
|
|
cam_vio-supply = <&L4B>;
|
||
|
|
cam_vdig-supply = <&cam_dvdd_front>;
|
||
|
|
cam_clk-supply = <&cam_cc_titan_top_gdsc>;
|
||
|
|
cam_vana-supply = <&camera_ldo5>;
|
||
|
|
regulator-names = "cam_vdig",
|
||
|
|
"cam_clk", "cam_vana","cam_vio";
|
||
|
|
rgltr-cntrl-support;
|
||
|
|
rgltr-min-voltage = <1050000 0 2800000 1800000>;
|
||
|
|
rgltr-max-voltage = <1050000 0 2800000 1800000>;
|
||
|
|
rgltr-load-current = <125000 0 95000 3000>;
|
||
|
|
gpio-no-mux = <0>;
|
||
|
|
pinctrl-names = "cam_default", "cam_suspend";
|
||
|
|
pinctrl-0 = <&cam_sensor_mclk4_active
|
||
|
|
&cam_sensor_active_rst4>;
|
||
|
|
pinctrl-1 = <&cam_sensor_mclk4_suspend
|
||
|
|
&cam_sensor_suspend_rst4>;
|
||
|
|
gpios = <&tlmm 104 0>,
|
||
|
|
<&tlmm 120 0>;
|
||
|
|
gpio-reset = <1>;
|
||
|
|
gpio-req-tbl-num = <0 1>;
|
||
|
|
gpio-req-tbl-flags = <1 0>;
|
||
|
|
gpio-req-tbl-label = "CAMIF_MCLK4",
|
||
|
|
"CAM_RESET4";
|
||
|
|
cci-master = <CCI_MASTER_1>;
|
||
|
|
clocks = <&camcc CAM_CC_MCLK4_CLK>;
|
||
|
|
clock-names = "cam_clk";
|
||
|
|
clock-cntl-level = "nominal";
|
||
|
|
clock-rates = <24000000>;
|
||
|
|
status = "ok";
|
||
|
|
};
|
||
|
|
|
||
|
|
actuator_tele: qcom,actuator3{
|
||
|
|
cell-index = <3>;
|
||
|
|
compatible = "qcom,actuator";
|
||
|
|
cci-master = <CCI_MASTER_0>;
|
||
|
|
cam_vio-supply = <&L4B>;
|
||
|
|
cam_vaf-supply = <&camera_ldo7>;
|
||
|
|
cam_v_custom1-supply = <&cam_ois_af_vdd_tele>;
|
||
|
|
regulator-names = "cam_vio", "cam_vaf", "cam_v_custom1";
|
||
|
|
rgltr-cntrl-support;
|
||
|
|
rgltr-min-voltage = <1800000 2800000 2800000>;
|
||
|
|
rgltr-max-voltage = <1800000 2804000 2800000>;
|
||
|
|
rgltr-load-current = <1000 227000 20000>;
|
||
|
|
af-ois-use-same-ic;
|
||
|
|
status = "ok";
|
||
|
|
};
|
||
|
|
|
||
|
|
ois_tele: qcom,ois3 {
|
||
|
|
cell-index = <3>;
|
||
|
|
compatible = "qcom,ois";
|
||
|
|
cci-master = <CCI_MASTER_0>;
|
||
|
|
cam_vio-supply = <&L4B>;
|
||
|
|
cam_vaf-supply = <&camera_ldo7>;
|
||
|
|
cam_v_custom1-supply = <&cam_ois_af_vdd_tele>;
|
||
|
|
regulator-names = "cam_vio", "cam_vaf", "cam_v_custom1";
|
||
|
|
rgltr-cntrl-support;
|
||
|
|
rgltr-min-voltage = <1800000 2800000 2800000>;
|
||
|
|
rgltr-max-voltage = <1800000 2804000 2800000>;
|
||
|
|
rgltr-load-current = <1000 227000 20000>;
|
||
|
|
status = "ok";
|
||
|
|
};
|
||
|
|
|
||
|
|
eeprom_tele: qcom,eeprom3 {
|
||
|
|
cell-index = <3>;
|
||
|
|
reg = <0x03>;
|
||
|
|
compatible = "qcom,eeprom";
|
||
|
|
cci-master = <CCI_MASTER_0>;
|
||
|
|
cam_vio-supply = <&L4B>;
|
||
|
|
cam_vaf-supply = <&camera_ldo7>;
|
||
|
|
cam_v_custom1-supply = <&cam_ois_af_vdd_tele>;
|
||
|
|
regulator-names = "cam_vio", "cam_vaf", "cam_v_custom1";
|
||
|
|
rgltr-cntrl-support;
|
||
|
|
rgltr-min-voltage = <1800000 2800000 2800000>;
|
||
|
|
rgltr-max-voltage = <1800000 2804000 2800000>;
|
||
|
|
rgltr-load-current = <1000 227000 20000>;
|
||
|
|
status = "ok";
|
||
|
|
};
|
||
|
|
|
||
|
|
rear_tele:qcom,cam-sensor3 {
|
||
|
|
cell-index = <3>;
|
||
|
|
compatible = "qcom,cam-sensor";
|
||
|
|
csiphy-sd-index = <0>;
|
||
|
|
sensor-position-roll = <90>;
|
||
|
|
sensor-position-pitch = <0>;
|
||
|
|
sensor-position-yaw = <180>;
|
||
|
|
actuator-src = <&actuator_tele>;
|
||
|
|
ois-src = <&ois_tele>;
|
||
|
|
eeprom-src = <&eeprom_tele>;
|
||
|
|
led-flash-src = <&led_flash_rear_tele>;
|
||
|
|
cam_vio-supply = <&L4B>;
|
||
|
|
cam_vdig-supply = <&camera_ldo2>;
|
||
|
|
cam_clk-supply = <&cam_cc_titan_top_gdsc>;
|
||
|
|
cam_vana-supply = <&camera_ldo6>;
|
||
|
|
regulator-names = "cam_vio", "cam_vdig",
|
||
|
|
"cam_clk", "cam_vana";
|
||
|
|
rgltr-cntrl-support;
|
||
|
|
rgltr-min-voltage = <1800000 1100000 0 2800000>;
|
||
|
|
rgltr-max-voltage = <1800000 1104000 0 2800000>;
|
||
|
|
rgltr-load-current = <155000 680000 0 50000>;
|
||
|
|
gpio-no-mux = <0>;
|
||
|
|
pinctrl-names = "cam_default", "cam_suspend";
|
||
|
|
pinctrl-0 = <&cam_sensor_mclk3_active
|
||
|
|
&cam_sensor_active_rst3>;
|
||
|
|
pinctrl-1 = <&cam_sensor_mclk3_suspend
|
||
|
|
&cam_sensor_suspend_rst3>;
|
||
|
|
gpios = <&tlmm 103 0>,
|
||
|
|
<&tlmm 119 0>;
|
||
|
|
gpio-reset = <1>;
|
||
|
|
gpio-req-tbl-num = <0 1>;
|
||
|
|
gpio-req-tbl-flags = <1 0>;
|
||
|
|
gpio-req-tbl-label = "CAMIF_MCLK3",
|
||
|
|
"CAM_RESET3";
|
||
|
|
cci-master = <CCI_MASTER_0>;
|
||
|
|
clocks = <&camcc CAM_CC_MCLK3_CLK>;
|
||
|
|
clock-names = "cam_clk";
|
||
|
|
clock-cntl-level = "nominal";
|
||
|
|
clock-rates = <19200000>;
|
||
|
|
status = "ok";
|
||
|
|
};
|
||
|
|
};
|