90 lines
2.2 KiB
Text
90 lines
2.2 KiB
Text
|
/* Copyright (c) 2021, The Linux Foundation. All rights reserved.
|
||
|
|
*
|
||
|
|
* This program is free software; you can redistribute it and/or modify
|
||
|
|
* it under the terms of the GNU General Public License version 2 and
|
||
|
|
* only version 2 as published by the Free Software Foundation.
|
||
|
|
*
|
||
|
|
* This program is distributed in the hope that it will be useful,
|
||
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||
|
|
* GNU General Public License for more details.
|
||
|
|
*/
|
||
|
|
|
||
|
|
#include <dt-bindings/clock/qcom,rpmh.h>
|
||
|
|
#include "kalama-arc-products-common-overlay.dtsi"
|
||
|
|
#include "kalama-moto-common-charger.dtsi"
|
||
|
|
#include "kalama-arc-charger-overlay.dtsi"
|
||
|
|
#include "kalama-arc-haptics-overlay.dtsi"
|
||
|
|
#include "kalama-moto-common-st-nfc.dtsi"
|
||
|
|
#include "kalama-arc-touchscreen-overlay.dtsi"
|
||
|
|
#include "kalama-arc-fingerprint-overlay.dtsi"
|
||
|
|
#include "kalama-arc-evb-sensors-overlay.dtsi"
|
||
|
|
|
||
|
|
#include "kalama-arc-thermal-overlay.dtsi"
|
||
|
|
#include "moto-arc-wl2868c.dtsi"
|
||
|
|
|
||
|
|
&soc {
|
||
|
|
mmi_relay {
|
||
|
|
compatible = "mmi,sys-relay";
|
||
|
|
};
|
||
|
|
|
||
|
|
lpd_mitigate: mmi,lpd-mitigate {
|
||
|
|
compatible = "mmi,lpd-mitigate";
|
||
|
|
mmi,mitigate-mode-cfg = <3>;
|
||
|
|
mmi,default-mitigate-mode-cfg = <1>;
|
||
|
|
};
|
||
|
|
|
||
|
|
usb_nop_phy: usb_nop_phy {
|
||
|
|
compatible = "usb-nop-xceiv";
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
&usb_qmp_dp_phy {
|
||
|
|
status = "disabled";
|
||
|
|
};
|
||
|
|
|
||
|
|
&usb0 {
|
||
|
|
dwc3@a600000 {
|
||
|
|
usb-phy = <&eusb2_phy0>, <&usb_nop_phy>;
|
||
|
|
maximum-speed = "high-speed";
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
&ufshc_mem {
|
||
|
|
limit-tx-hs-gear = <4>;
|
||
|
|
limit-rx-hs-gear = <4>;
|
||
|
|
limit-rate = <1>; /* HS Rate-A */
|
||
|
|
status = "ok";
|
||
|
|
};
|
||
|
|
|
||
|
|
&pm8550b_eusb2_repeater {
|
||
|
|
qcom,param-override-seq =
|
||
|
|
/* <value reg_offset> */
|
||
|
|
/* Adjust HS trasmit amplitude */
|
||
|
|
<0xb 0x51
|
||
|
|
/* HS disconnect threshold */
|
||
|
|
0x6 0x53
|
||
|
|
/* Squelch detection threshold */
|
||
|
|
0x4 0x54
|
||
|
|
/* Tx pre-emphasis tuning */
|
||
|
|
0x6 0x57>;
|
||
|
|
|
||
|
|
qcom,host-param-override-seq =
|
||
|
|
/* <value reg_offset> */
|
||
|
|
/* Adjust HS trasmit amplitude */
|
||
|
|
<0xa 0x51
|
||
|
|
/* HS disconnect threshold */
|
||
|
|
0x6 0x53
|
||
|
|
/* Squelch detection threshold */
|
||
|
|
0x5 0x54
|
||
|
|
/* Tx pre-emphasis tuning */
|
||
|
|
0x6 0x57>;
|
||
|
|
};
|
||
|
|
|
||
|
|
&BOB2 {
|
||
|
|
regulator-min-microvolt = <2704000>;
|
||
|
|
regulator-max-microvolt = <3208000>;
|
||
|
|
qcom,init-voltage = <3100000>;
|
||
|
|
regulator-boot-on;
|
||
|
|
};
|