108 lines
2.8 KiB
Text
108 lines
2.8 KiB
Text
|
/* Copyright (c) 2021, The Linux Foundation. All rights reserved.
|
||
|
|
*
|
||
|
|
* This program is free software; you can redistribute it and/or modify
|
||
|
|
* it under the terms of the GNU General Public License version 2 and
|
||
|
|
* only version 2 as published by the Free Software Foundation.
|
||
|
|
*
|
||
|
|
* This program is distributed in the hope that it will be useful,
|
||
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||
|
|
* GNU General Public License for more details.
|
||
|
|
*/
|
||
|
|
|
||
|
|
/* This file is only for rtwo device */
|
||
|
|
|
||
|
|
#include "kalama-rtwo-products-common-overlay.dtsi"
|
||
|
|
#include "kalama-rtwo-haptics-overlay.dtsi"
|
||
|
|
#include "kalama-rtwo-fingerprint-overlay.dtsi"
|
||
|
|
#include "kalama-rtwo-touchscreen-overlay.dtsi"
|
||
|
|
#include "moto-rtwo-wl2868c.dtsi"
|
||
|
|
#include <dt-bindings/regulator/qcom,rpmh-regulator-levels.h>
|
||
|
|
#include "kalama-rtwo-evb-sensors-overlay.dtsi"
|
||
|
|
#include "kalama-rtwo-thermal-overlay.dtsi"
|
||
|
|
#include "kalama-moto-common-charger.dtsi"
|
||
|
|
#include "kalama-rtwo-charger-overlay.dtsi"
|
||
|
|
|
||
|
|
&soc {
|
||
|
|
mmi_relay {
|
||
|
|
compatible = "mmi,sys-relay";
|
||
|
|
};
|
||
|
|
|
||
|
|
lpd_mitigate: mmi,lpd-mitigate {
|
||
|
|
compatible = "mmi,lpd-mitigate";
|
||
|
|
mmi,mitigate-mode-cfg = <3>;
|
||
|
|
mmi,default-mitigate-mode-cfg = <1>;
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
&tlmm {
|
||
|
|
redriver_enable: redriver_enable {
|
||
|
|
mux {
|
||
|
|
pins = "gpio22";
|
||
|
|
function = "gpio";
|
||
|
|
};
|
||
|
|
|
||
|
|
config {
|
||
|
|
pins = "gpio22";
|
||
|
|
drive-strength = <2>;
|
||
|
|
bias-disable; /* NO PULL */
|
||
|
|
output-high;
|
||
|
|
};
|
||
|
|
};
|
||
|
|
redriver_disable: redriver_disable {
|
||
|
|
mux {
|
||
|
|
pins = "gpio22";
|
||
|
|
function = "gpio";
|
||
|
|
};
|
||
|
|
|
||
|
|
config {
|
||
|
|
pins = "gpio22";
|
||
|
|
drive-strength = <2>;
|
||
|
|
output-low;
|
||
|
|
};
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
&qupv3_hub_i2c2 {
|
||
|
|
status = "ok";
|
||
|
|
#include "kalama-moto-common-redriver.dtsi"
|
||
|
|
};
|
||
|
|
|
||
|
|
&usb0 {
|
||
|
|
ssusb_redriver = <&redriver>;
|
||
|
|
};
|
||
|
|
|
||
|
|
&pm8550b_eusb2_repeater {
|
||
|
|
qcom,host-param-override-seq =
|
||
|
|
/* <value reg_offset> */
|
||
|
|
/* Adjust HS trasmit amplitude */
|
||
|
|
<0xa 0x51
|
||
|
|
/* HS disconnect threshold */
|
||
|
|
0x6 0x53
|
||
|
|
/* Squelch detection threshold */
|
||
|
|
0x5 0x54
|
||
|
|
/* Tx pre-emphasis tuning */
|
||
|
|
0x6 0x57>;
|
||
|
|
};
|
||
|
|
|
||
|
|
&apps_rsc_drv2 {
|
||
|
|
rpmh-regulator-ldob4 {
|
||
|
|
compatible = "qcom,rpmh-vrm-regulator";
|
||
|
|
qcom,resource-name = "ldob4";
|
||
|
|
qcom,regulator-type = "pmic5-ldo";
|
||
|
|
qcom,supported-modes =
|
||
|
|
<RPMH_REGULATOR_MODE_LPM
|
||
|
|
RPMH_REGULATOR_MODE_HPM>;
|
||
|
|
qcom,mode-threshold-currents = <0 10000>;
|
||
|
|
|
||
|
|
L4B: pm_humu_l4: regulator-pm-humu-l4 {
|
||
|
|
regulator-name = "pm_humu_l4";
|
||
|
|
qcom,set = <RPMH_REGULATOR_SET_ALL>;
|
||
|
|
regulator-min-microvolt = <1800000>;
|
||
|
|
regulator-max-microvolt = <1800000>;
|
||
|
|
qcom,init-voltage = <1800000>;
|
||
|
|
qcom,init-mode = <RPMH_REGULATOR_MODE_HPM>;
|
||
|
|
};
|
||
|
|
};
|
||
|
|
};
|