Rtwo/kernel/motorola/sm8550-devicetrees/qcom/qcs405-usb.dtsi

#include <dt-bindings/clock/qcom,gcc-qcs404.h>
#include <dt-bindings/interconnect/qcom,qcs405.h>

&soc {
	/* Secondary USB port related controller */
	usb3: ssusb@7580000 {
		compatible = "qcom,dwc-usb3-msm";
		reg = <0x7580000 0x100000>;
		reg-names = "core_base";
		#address-cells = <1>;
		#size-cells = <1>;
		ranges;

		interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>,
			<GIC_SPI 319 IRQ_TYPE_LEVEL_HIGH>;
		interrupt-names = "pwr_event_irq", "hs_phy_irq";

		dpdm-supply = <&usb2_phy0>;
		clocks = <&gcc GCC_USB30_MASTER_CLK>,
			 <&gcc GCC_SYS_NOC_USB3_CLK>,
			 <&gcc GCC_USB30_SLEEP_CLK>,
			 <&gcc GCC_USB30_MOCK_UTMI_CLK>,
			 <&rpmcc RPM_SMD_XO_CLK_SRC>,
			 <&gcc GCC_PCNOC_USB3_CLK>;
		clock-names = "core_clk", "iface_clk", "sleep_clk",
				"utmi_clk", "xo", "noc_aggr_clk";

		qcom,core-clk-rate = <200000000>;
		qcom,core-clk-rate-hs = <100000000>;

		qcom,pm-qos-latency = <181>;
		qcom,default-bus-vote = <2>; /* use svs bus voting */
		interconnect-names = "usb-ddr", "ddr-usb";
		interconnects = <&system_noc MASTER_USB3 &bimc SLAVE_EBI_CH0>,
				<&bimc MASTER_AMPSS_M0 &pc_noc SLAVE_USB3>;

		resets = <&gcc GCC_USB_30_BCR>;
		reset-names = "core_reset";

		status = "disabled";
		dwc3@7580000 {
			compatible = "snps,dwc3";
			reg = <0x7580000 0xcd00>;
			interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
			usb-phy = <&usb2_phy1>, <&usb_ss_phy>;
			linux,sysdev_is_parent;
			snps,disable-clk-gating;
			snps,has-lpm-erratum;
			snps,hird-threshold = /bits/ 8 <0x10>;
			snps,dis-u1-entry-quirk;
			snps,dis-u2-entry-quirk;
			snps,dis_u2_susphy_quirk;
			snps,dis_enblslpm_quirk;
			maximum-speed = "super-speed";
			dr_mode = "host";
		};
	};

	/* Secondary USB port related High Speed PHY */
	usb2_phy1: hsphy@7a000 {
		compatible = "qcom,usb-snps-hsphy";
		reg = <0x7a000 0x200>;
		reg-names = "phy_csr";

		vdd-supply = <&pms405_l4>;
		vdda18-supply = <&pms405_l5>;
		vdda33-supply = <&pms405_l12>;
		qcom,vdd-voltage-level = <0 1144000 1200000>;

		clocks = <&rpmcc RPM_SMD_XO_CLK_SRC>,
			 <&gcc GCC_USB_HS_PHY_CFG_AHB_CLK>,
			 <&gcc GCC_USB2A_PHY_SLEEP_CLK>;
		clock-names = "ref_clk", "phy_csr_clk", "sleep_clk";

		resets = <&gcc GCC_USB_HS_PHY_CFG_AHB_BCR>,
			 <&gcc GCC_USB2A_PHY_BCR>;
		reset-names = "phy_reset", "phy_por_reset";

		qcom,snps-hs-phy-init-seq =
			<0xc0 0x01 0>,
			<0xe8 0x0d 0>,
			<0x74 0x12 0>,
			<0x98 0x63 0>,
			<0x9c 0x03 0>,
			<0xa0 0x1d 0>,
			<0xa4 0x03 0>,
			<0x8c 0x23 0>,
			<0x78 0x08 0>,
			<0x7c 0xdc 0>,
			<0x90 0xe0 20>,
			<0x74 0x10 0>,
			<0x90 0x60 0>,
			<0xffffffff 0xffffffff 0>;
		status = "disabled";
	};

	/* Secondary USB port related Super Speed PHY */
	usb_ss_phy: ssphy@78000 {
		compatible = "qcom,usb-ssphy";
		reg = <0x78000 0x400>;
		vdd-supply = <&pms405_l3>;
		vdda18-supply = <&pms405_l5>;
		qcom,vdd-voltage-level = <0 1050000 1050000>;

		clocks = //<&cmn_blk_pll CMN_BLK_PLL>,
			 <&gcc GCC_USB_HS_PHY_CFG_AHB_CLK>,
			 <&gcc GCC_USB3_PHY_PIPE_CLK>;
		clock-names = "ref_clk", "cfg_ahb_clk", "pipe_clk";

		resets = <&gcc GCC_USB3_PHY_BCR>,
			 <&gcc GCC_USB3PHY_PHY_BCR>;
		reset-names = "phy_reset", "phy_com_reset";
		status = "disabled";
	};

	usb_nop_phy: usb_nop_phy {
		compatible = "usb-nop-xceiv";
	};

	/* Primary USB port related controller */
	usb2s: hsusb@78c0000 {
		compatible = "qcom,dwc-usb3-msm";
		reg = <0x78c0000 0x100000>;
		reg-names = "core_base";
		#address-cells = <1>;
		#size-cells = <1>;
		ranges;

		interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>,
			<GIC_SPI 318 IRQ_TYPE_LEVEL_HIGH>;
		interrupt-names = "pwr_event_irq", "hs_phy_irq";

		clocks = <&gcc GCC_USB_HS_SYSTEM_CLK>,
			 <&gcc GCC_PCNOC_USB2_CLK>,
			 <&gcc GCC_USB_HS_INACTIVITY_TIMERS_CLK>,
			 <&gcc GCC_USB20_MOCK_UTMI_CLK>,
			 <&rpmcc RPM_SMD_XO_CLK_SRC>;
		clock-names = "core_clk", "iface_clk", "sleep_clk",
				"utmi_clk", "xo";

		qcom,core-clk-rate = <133333333>;
		qcom,default-bus-vote = <2>; /* use svs bus voting */
		interconnect-names = "usb-ddr", "ddr-usb";
		interconnects = <&pc_noc MASTER_XM_USB_HS1 &bimc SLAVE_EBI_CH0>,
				<&bimc MASTER_AMPSS_M0 &pc_noc SLAVE_USB_HS>;


		resets = <&gcc GCC_USB_HS_BCR>;
		reset-names = "core_reset";

		dwc3@78c0000 {
			compatible = "snps,dwc3";
			reg = <0x78c0000 0xcd00>;
			interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>;
			usb-phy = <&usb2_phy0>, <&usb_nop_phy>;
			linux,sysdev_is_parent;
			snps,disable-clk-gating;
			snps,has-lpm-erratum;
			snps,hird-threshold = /bits/ 8 <0x10>;
			snps,dis-u1-entry-quirk;
			snps,dis-u2-entry-quirk;
			snps,dis_u2_susphy_quirk;
			snps,dis_enblslpm_quirk;
			maximum-speed = "high-speed";
			dr_mode = "otg";
			usb-role-switch;
		};
	};

	/* Primary USB port related High Speed PHY */
	usb2_phy0: hsphy@7c000 {
		compatible = "qcom,usb-snps-hsphy";
		reg = <0x7c000 0x200>;
		reg-names = "phy_csr";

		vdd-supply = <&pms405_l4>;
		vdda18-supply = <&pms405_l5>;
		vdda33-supply = <&pms405_l12>;
		qcom,vdd-voltage-level = <0 1144000 1200000>;

		clocks = <&rpmcc RPM_SMD_XO_CLK_SRC>,
			 <&gcc GCC_USB_HS_PHY_CFG_AHB_CLK>,
			 <&gcc GCC_USB2A_PHY_SLEEP_CLK>;
		clock-names = "ref_clk", "phy_csr_clk", "sleep_clk";

		resets = <&gcc GCC_QUSB2_PHY_BCR>,
			 <&gcc GCC_USB2_HS_PHY_ONLY_BCR>;
		reset-names = "phy_reset", "phy_por_reset";

		qcom,snps-hs-phy-init-seq =
			<0xc0 0x01 0>,
			<0xe8 0x0d 0>,
			<0x74 0x12 0>,
			<0x98 0x63 0>,
			<0x9c 0x03 0>,
			<0xa0 0x1d 0>,
			<0xa4 0x03 0>,
			<0x8c 0x23 0>,
			<0x78 0x08 0>,
			<0x7c 0xdc 0>,
			<0x90 0xe0 20>,
			<0x74 0x10 0>,
			<0x90 0x60 0>,
			<0xffffffff 0xffffffff 0>;
	};

};