242 lines
6.6 KiB
Text
242 lines
6.6 KiB
Text
|
#include <dt-bindings/msm-camera.h>
|
||
|
|
#include <dt-bindings/regulator/qcom,rpmh-regulator-levels.h>
|
||
|
|
|
||
|
|
&apps_rsc_drv2 {
|
||
|
|
rpmh-regulator-ldob4 {
|
||
|
|
compatible = "qcom,rpmh-vrm-regulator";
|
||
|
|
qcom,resource-name = "ldob4";
|
||
|
|
qcom,regulator-type = "pmic5-ldo";
|
||
|
|
qcom,supported-modes =
|
||
|
|
<RPMH_REGULATOR_MODE_LPM
|
||
|
|
RPMH_REGULATOR_MODE_HPM>;
|
||
|
|
qcom,mode-threshold-currents = <0 10000>;
|
||
|
|
|
||
|
|
L4B: pm_humu_l4: regulator-pm-humu-l4 {
|
||
|
|
regulator-name = "pm_humu_l4";
|
||
|
|
qcom,set = <RPMH_REGULATOR_SET_ALL>;
|
||
|
|
regulator-min-microvolt = <1800000>;
|
||
|
|
regulator-max-microvolt = <1800000>;
|
||
|
|
qcom,init-voltage = <1800000>;
|
||
|
|
qcom,init-mode = <RPMH_REGULATOR_MODE_HPM>;
|
||
|
|
};
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
&tlmm {
|
||
|
|
/* tele s5kjn1 avdd*/
|
||
|
|
cam_avdd_tele_en_default: cam_avdd_tele_en_default {
|
||
|
|
mux {
|
||
|
|
pins = "gpio1";
|
||
|
|
function = "gpio";
|
||
|
|
};
|
||
|
|
|
||
|
|
config {
|
||
|
|
pins = "gpio1";
|
||
|
|
bias-pull-down; /* PULL DOWN */
|
||
|
|
drive-strength = <2>; /* 2 MA */
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
|
||
|
|
/* tele s5kjn1 dvdd*/
|
||
|
|
cam_dvdd_tele_en_default: cam_dvdd_tele_en_default {
|
||
|
|
mux {
|
||
|
|
pins = "gpio0";
|
||
|
|
function = "gpio";
|
||
|
|
};
|
||
|
|
|
||
|
|
config {
|
||
|
|
pins = "gpio0";
|
||
|
|
bias-pull-down; /* PULL DOWN */
|
||
|
|
drive-strength = <2>; /* 2 MA */
|
||
|
|
};
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
&soc {
|
||
|
|
/* tele s5kjn1 avdd*/
|
||
|
|
cam_avdd_tele: gpio-regulator@0 {
|
||
|
|
compatible = "regulator-fixed";
|
||
|
|
reg = <0x00 0x00>;
|
||
|
|
regulator-name = "cam_avdd_tele";
|
||
|
|
regulator-min-microvolt = <2800000>;
|
||
|
|
regulator-max-microvolt = <2800000>;
|
||
|
|
regulator-enable-ramp-delay = <233>;
|
||
|
|
enable-active-high;
|
||
|
|
gpio = <&tlmm 1 0>;
|
||
|
|
pinctrl-names = "default";
|
||
|
|
pinctrl-0 = <&cam_avdd_tele_en_default>;
|
||
|
|
vin-supply = <&BOB1>;
|
||
|
|
};
|
||
|
|
|
||
|
|
/* tele s5kjn1 dvdd*/
|
||
|
|
cam_dvdd_tele: gpio-regulator@1 {
|
||
|
|
compatible = "regulator-fixed";
|
||
|
|
reg = <0x01 0x00>;
|
||
|
|
regulator-name = "cam_dvdd_tele";
|
||
|
|
regulator-min-microvolt = <1100000>;
|
||
|
|
regulator-max-microvolt = <1100000>;
|
||
|
|
regulator-enable-ramp-delay = <233>;
|
||
|
|
enable-active-high;
|
||
|
|
gpio = <&tlmm 0 0>;
|
||
|
|
pinctrl-names = "default";
|
||
|
|
pinctrl-0 = <&cam_dvdd_tele_en_default>;
|
||
|
|
vin-supply = <&S4G>;
|
||
|
|
};
|
||
|
|
|
||
|
|
qcom,cam-res-mgr {
|
||
|
|
compatible = "qcom,cam-res-mgr";
|
||
|
|
status = "ok";
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
&cam_cci0 {
|
||
|
|
|
||
|
|
actuator_rear_main: qcom,actuator0{
|
||
|
|
cell-index = <0>;
|
||
|
|
compatible = "qcom,actuator";
|
||
|
|
cci-master = <CCI_MASTER_0>;
|
||
|
|
cam_vaf-supply = <&camera_ldo7>;
|
||
|
|
regulator-names = "cam_vaf";
|
||
|
|
rgltr-cntrl-support;
|
||
|
|
rgltr-min-voltage = <2800000>;
|
||
|
|
rgltr-max-voltage = <2800000>;
|
||
|
|
rgltr-load-current = <119000>;
|
||
|
|
status = "ok";
|
||
|
|
};
|
||
|
|
|
||
|
|
/* main s5kgn8 sensor*/
|
||
|
|
qcom,cam-sensor0 {
|
||
|
|
cell-index = <0>;
|
||
|
|
compatible = "qcom,cam-sensor";
|
||
|
|
csiphy-sd-index = <4>;
|
||
|
|
actuator-src = <&actuator_rear_main>;
|
||
|
|
sensor-position-roll = <90>;
|
||
|
|
sensor-position-pitch = <0>;
|
||
|
|
sensor-position-yaw = <180>;
|
||
|
|
cam_vio-supply = <&L4B>;
|
||
|
|
cam_vdig-supply = <&camera_ldo1>;
|
||
|
|
cam_clk-supply = <&cam_cc_titan_top_gdsc>;
|
||
|
|
cam_vana-supply = <&camera_ldo3>;
|
||
|
|
cam_vaf-supply = <&camera_ldo7>;
|
||
|
|
regulator-names = "cam_vana",
|
||
|
|
"cam_vdig","cam_clk","cam_vio";
|
||
|
|
rgltr-cntrl-support;
|
||
|
|
rgltr-min-voltage = <2200000 1000000 0 1800000>;
|
||
|
|
rgltr-max-voltage = <2200000 1000000 0 1800000>;
|
||
|
|
rgltr-load-current = <101000 787000 0 1000>;
|
||
|
|
gpio-no-mux = <0>;
|
||
|
|
|
||
|
|
pinctrl-names = "cam_default", "cam_suspend";
|
||
|
|
pinctrl-0 = <&cam_sensor_mclk1_active
|
||
|
|
&cam_sensor_active_rst2>;
|
||
|
|
pinctrl-1 = <&cam_sensor_mclk1_suspend
|
||
|
|
&cam_sensor_suspend_rst2>;
|
||
|
|
gpios = <&tlmm 101 0>,
|
||
|
|
<&tlmm 117 0>;
|
||
|
|
gpio-reset = <1>;
|
||
|
|
gpio-req-tbl-num = <0 1>;
|
||
|
|
gpio-req-tbl-flags = <1 0>;
|
||
|
|
gpio-req-tbl-label = "CAMIF_MCLK1",
|
||
|
|
"CAM_RESET1";
|
||
|
|
cci-master = <CCI_MASTER_0>;
|
||
|
|
clocks = <&camcc CAM_CC_MCLK1_CLK>;
|
||
|
|
clock-names = "cam_clk";
|
||
|
|
clock-cntl-level = "nominal";
|
||
|
|
clock-rates = <24000000>;
|
||
|
|
status = "ok";
|
||
|
|
};
|
||
|
|
|
||
|
|
|
||
|
|
/* tele s5kjn1 sensor*/
|
||
|
|
qcom,cam-sensor2 {
|
||
|
|
cell-index = <2>;
|
||
|
|
compatible = "qcom,cam-sensor";
|
||
|
|
csiphy-sd-index = <1>;
|
||
|
|
sensor-position-roll = <90>;
|
||
|
|
sensor-position-pitch = <0>;
|
||
|
|
sensor-position-yaw = <180>;
|
||
|
|
|
||
|
|
cam_vio-supply = <&L4B>;
|
||
|
|
cam_vdig-supply = <&cam_dvdd_tele>;
|
||
|
|
cam_clk-supply = <&cam_cc_titan_top_gdsc>;
|
||
|
|
cam_vana-supply = <&cam_avdd_tele>;
|
||
|
|
regulator-names = "cam_vio", "cam_vdig", "cam_clk", "cam_vana";
|
||
|
|
rgltr-cntrl-support;
|
||
|
|
rgltr-min-voltage = <1800000 1100000 0 2800000>;
|
||
|
|
rgltr-max-voltage = <1800000 1100000 0 2800000>;
|
||
|
|
rgltr-load-current = <3500 125000 0 95000>;
|
||
|
|
|
||
|
|
gpio-no-mux = <0>;
|
||
|
|
pinctrl-names = "cam_default", "cam_suspend";
|
||
|
|
pinctrl-0 = <&cam_sensor_mclk2_active &cam_sensor_active_rst2>;
|
||
|
|
pinctrl-1 = <&cam_sensor_mclk2_suspend &cam_sensor_suspend_rst2>;
|
||
|
|
gpios = <&tlmm 102 0>, <&tlmm 118 0>;
|
||
|
|
gpio-reset = <1>;
|
||
|
|
gpio-req-tbl-num = <0 1>;
|
||
|
|
gpio-req-tbl-flags = <1 0>;
|
||
|
|
gpio-req-tbl-label = "CAMIF_MCLK2", "CAM_RESET2";
|
||
|
|
cci-master = <CCI_MASTER_1>;
|
||
|
|
clocks = <&camcc CAM_CC_MCLK2_CLK>;
|
||
|
|
clock-names = "cam_clk";
|
||
|
|
clock-cntl-level = "nominal";
|
||
|
|
clock-rates = <24000000>;
|
||
|
|
status = "ok";
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
&cam_cci1 {
|
||
|
|
eeprom_front: qcom,eeprom@1 {
|
||
|
|
cell-index = <1>;
|
||
|
|
compatible = "qcom,eeprom";
|
||
|
|
cci-master = <CCI_MASTER_0>;
|
||
|
|
cam_vio-supply = <&L4B>;
|
||
|
|
regulator-names = "cam_vio";
|
||
|
|
rgltr-cntrl-support;
|
||
|
|
rgltr-min-voltage = <1800000>;
|
||
|
|
rgltr-max-voltage = <1800000>;
|
||
|
|
rgltr-load-current = <3000>;
|
||
|
|
status = "ok";
|
||
|
|
};
|
||
|
|
|
||
|
|
/* temp set ldo2 1.2V */
|
||
|
|
qcom,cam-sensor1 {
|
||
|
|
cell-index = <1>;
|
||
|
|
compatible = "qcom,cam-sensor";
|
||
|
|
csiphy-sd-index = <5>;
|
||
|
|
sensor-position-roll = <270>;
|
||
|
|
sensor-position-pitch = <0>;
|
||
|
|
sensor-position-yaw = <0>;
|
||
|
|
eeprom-src = <&eeprom_front>;
|
||
|
|
cam_vio-supply = <&L4B>;
|
||
|
|
cam_vdig-supply = <&camera_ldo2>;
|
||
|
|
cam_clk-supply = <&cam_cc_titan_top_gdsc>;
|
||
|
|
cam_vana-supply = <&camera_ldo4>;
|
||
|
|
regulator-names = "cam_vio", "cam_vdig", "cam_clk",
|
||
|
|
"cam_vana";
|
||
|
|
rgltr-cntrl-support;
|
||
|
|
rgltr-min-voltage = <1800000 1104000 0 2800000>;
|
||
|
|
rgltr-max-voltage = <1800000 1104000 0 2800000>;
|
||
|
|
rgltr-load-current = <10000 140400 0 52000>;
|
||
|
|
gpio-no-mux = <0>;
|
||
|
|
pinctrl-names = "cam_default", "cam_suspend";
|
||
|
|
pinctrl-0 = <&cam_sensor_mclk4_active
|
||
|
|
&cam_sensor_active_rst4>;
|
||
|
|
pinctrl-1 = <&cam_sensor_mclk4_suspend
|
||
|
|
&cam_sensor_suspend_rst4>;
|
||
|
|
gpios = <&tlmm 104 0>,
|
||
|
|
<&tlmm 120 0>;
|
||
|
|
gpio-reset = <1>;
|
||
|
|
gpio-req-tbl-num = <0 1>;
|
||
|
|
gpio-req-tbl-flags = <1 0>;
|
||
|
|
gpio-req-tbl-label = "CAMIF_MCLK4",
|
||
|
|
"CAM_RESET4";
|
||
|
|
cci-master = <CCI_MASTER_0>;
|
||
|
|
clocks = <&camcc CAM_CC_MCLK4_CLK>;
|
||
|
|
clock-names = "cam_clk";
|
||
|
|
clock-cntl-level = "nominal";
|
||
|
|
clock-rates = <24000000>;
|
||
|
|
status = "ok";
|
||
|
|
};
|
||
|
|
};
|