Rtwo/kernel/motorola/sm8550-devicetrees/qcom/kalama-oberon-evb-overlay.dts

/* Copyright (c) 2022, The Linux Foundation. All rights reserved.
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License version 2 and
 * only version 2 as published by the Free Software Foundation.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 */

/* This is derivated from Qcom kalama-mtp-overlay.dts */

/dts-v1/;
/plugin/;

#include "kalama-oberon-device-common-overlay.dtsi"
#include <dt-bindings/leds/common.h>

/ {
	model = "oberon";
	compatible = "qcom,kalama-mtp", "qcom,kalama", "qcom,mtp", "qcom,oberon";
	qcom,msm-id = <519 0x10000>, <536 0x10000>, <519 0x20000>, <536 0x20000>;
	qcom,board-id = <0x47 0x9000>;
};

&tlmm {
	uwb_irq: uwb_irq {
		mux {
			pins = "gpio137";
			function = "gpio";
		};

		config {
			pins = "gpio137";
			bias-pull-down;
		};
	};
	lp5562_enable: lp5562_enable {
		mux {
			pins = "gpio74";
			function = "gpio";
		};

		config {
			pins = "gpio74";
			drive-strength = <2>;
			bias-disable; /* NO PULL */
			output-high;
		};
	};
	lp5562_disable: lp5562_disable {
		mux {
			pins = "gpio74";
			function = "gpio";
		};

		config {
			pins = "gpio74";
			drive-strength = <2>;
			output-low;
		};
	};
};

&pm8550b_eusb2_repeater {
	qcom,param-override-seq =
		/* <value reg_offset> */
		/* Adjust HS trasmit amplitude */
		<0xb 0x51
		/* HS disconnect threshold */
		 0x6 0x53
		/* Squelch detection threshold */
		 0x6 0x54
		/* Tx pre-emphasis tuning */
		 0x6 0x57>;
};

&qupv3_se4_spi {
	status = "disabled";
};

&qupv3_se10_spi {
	status = "ok";
	/*pinctrl-0 = <&qupv3_se18_spi_active &qupv3_se18_spi_cs0_active &qupv3_se18_spi_cs1_active>;*/
	/*pinctrl-1 = <&qupv3_se18_spi_sleep &qupv3_se18_spi_cs0_sleep &qupv3_se18_spi_cs1_sleep>;*/
	pinctrl-0 = <&qupv3_se10_spi_mosi_active>, <&qupv3_se10_spi_miso_active>,
		<&qupv3_se10_spi_clk_active>, <&qupv3_se10_spi_cs_active>;
	pinctrl-1 = <&qupv3_se10_spi_sleep>;
	sr100@0 {
		compatible = "nxp,sr100";
		reg = <0>;
		nxp,sr100-irq = <&tlmm 137 0x00>;
		nxp,sr100-ce = <&tlmm 144 0x00>;
		nxp,sr100-ri = <&tlmm 69 0x00>;
		interrupt-parent = <&tlmm>;
		interrupts = <137 0>;
		spi-max-frequency = <20000000>;
		pinctrl-names = "default";
		pinctrl-0 = <&uwb_irq>;
	};
};

&qupv3_hub_i2c2 {
	redriver@30 {
		status = "disabled";
	};

	led-controller@30 {
		#address-cells = <1>;
		#size-cells = <0>;
		status = "ok";
		compatible = "ti,lp5562";
		reg = <0x30>;
		pinctrl-names = "default";
		pinctrl-0 = <&lp5562_enable>;
		clock-mode = /bits/8 <2>;
		enable = <&tlmm 74 GPIO_ACTIVE_HIGH>;

		/* RGB led */
		chan@0 {
			chan-name = "red_moto";
			led-cur = /bits/ 8 <0x20>;
			max-cur = /bits/ 8 <0x60>;
			reg = <0>;
			color = <LED_COLOR_ID_RED>;
		};

		chan@1 {
			chan-name = "green_moto";
			led-cur = /bits/ 8 <0x20>;
			max-cur = /bits/ 8 <0x60>;
			reg = <1>;
			color = <LED_COLOR_ID_GREEN>;
		};

		chan@2 {
			chan-name = "blue_moto";
			led-cur = /bits/ 8 <0x20>;
			max-cur = /bits/ 8 <0x60>;
			reg = <2>;
			color = <LED_COLOR_ID_BLUE>;
		};

		chan@3 {
			chan-name = "white_moto";
			led-cur = /bits/ 8 <0x20>;
			max-cur = /bits/ 8 <0x60>;
			reg = <3>;
			color = <LED_COLOR_ID_WHITE>;
		};

		pattern@1 {
			/* Pulsing white pattern
			 *   LED:
			 *     027F: Ramp up 50%
			 *     027F: Ramp up 50%
			 *     4600: Wait 100ms
			 *     02FF: Ramp down 50%
			 *     02FF: Ramp down 50%
			 *     4600: Wait 100ms
			 *     0000: Goto start
			 */
			pat-name = "Pulsing White";

			pat-r = [02 7f 02 7f 46 00 02 ff 02 ff 46 00 00 00];
			pat-g = [02 7f 02 7f 46 00 02 ff 02 ff 46 00 00 00];
			pat-b = [02 7f 02 7f 46 00 02 ff 02 ff 46 00 00 00];
		};

		pattern@2 {
			/*
			 * HSV rainbow
			 *     40FF: Set PWM 255
			 *     41FF: Ramp down 50%
			 *     41FF: Ramp down 50%
			 *     41FF: Wait 1/2 ramp time
			 *     41FF: Wait 1/2 ramp time
			 *     417F: Ramp up 50%
			 *     417F: Ramp up 50%
			 *     0000: Goto start
			 *   Green:
			 *     4000: Set PWM 0
			 *     417F: Ramp up 50%
			 *     417F: Ramp up 50%
			 *     41FF: Ramp down 50%
			 *     41FF: Ramp down 50%
			 *     41FF: Wait 1/2 ramp time
			 *     41FF: Wait 1/2 ramp time
			 *     0000: Goto start
			 *   Blue:
			 *     4000: Set PWM 0
			 *     41FF: Wait 1/2 ramp time
			 *     41FF: Wait 1/2 ramp time
			 *     417F: Ramp up 50%
			 *     417F: Ramp up 50%
			 *     41FF: Ramp down 50%
			 *     41FF: Ramp down 50%
			 *     0000: Goto start
			 */
			pat-name = "HSV Rainbow";
			pat-r = [40 ff 41 FF 41 FF 41 FF 41 FF 41 7F 41 7F 00 00];
			pat-g = [40 00 41 7F 41 7F 41 FF 41 FF 41 FF 41 FF 00 00];
			pat-b = [40 00 41 FF 41 FF 41 7F 41 7F 41 FF 41 FF 00 00];
		};

		pattern@3 {
			/* Pulsing blue pattern
			 *   Blue:
			 *     027F: Ramp up 50%
			 *     027F: Ramp up 50%
			 *     4600: Wait 100ms
			 *     02FF: Ramp down 50%
			 *     02FF: Ramp down 50%
			 *     4600: Wait 100ms
			 *     0000: Goto start
			 */
			pat-name = "Pulsing Blue";
			pat-b = [02 7f 02 7f 46 00 02 ff 02 ff 46 00 00 00];
		};

	};
};

&pm8550_rgb {
	red {
		status = "ok";
		label = "charging_low";
		linux,default-trigger = "sign-of-life";
	};

	green {
		status = "ok";
		label = "charging_full";
		linux,default-trigger = "sign-of-life";
	};

	blue {
		status = "ok";
		label = "charging";
		linux,default-trigger = "sign-of-life";
	};
};