/* Copyright (c) 2023, The Linux Foundation. All rights reserved.
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License version 2 and
 * only version 2 as published by the Free Software Foundation.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 */

/* This file is only for Oberon device */

#include "kalama-moto-common-overlay-base.dtsi"
#include "kalama-moto-common-overlay.dtsi"
#include "kalama-rtwo-haptics-overlay.dtsi"
#include "kalama-oberon-fingerprint-overlay.dtsi"
#include "kalama-oberon-touchscreen-overlay.dtsi"
#include "moto-rtwo-wl2868c.dtsi"
#include <dt-bindings/regulator/qcom,rpmh-regulator-levels.h>
#include "kalama-rtwo-evb-sensors-overlay.dtsi"
#include "kalama-rtwo-thermal-overlay.dtsi"
#include "kalama-moto-common-charger.dtsi"
#include "kalama-rtwo-charger-overlay.dtsi"

&soc {
	mmi_relay {
		compatible = "mmi,sys-relay";
	};

	lpd_mitigate: mmi,lpd-mitigate {
		compatible = "mmi,lpd-mitigate";
		mmi,mitigate-mode-cfg = <3>;
		mmi,default-mitigate-mode-cfg = <1>;
	};

	qcom,qbt_handler {
		status = "disabled";
	};
};

&tlmm {
	redriver_enable: redriver_enable {
		mux {
			pins = "gpio22";
			function = "gpio";
		};

		config {
			pins = "gpio22";
			drive-strength = <2>;
			bias-disable; /* NO PULL */
			output-high;
		};
	};
	redriver_disable: redriver_disable {
		mux {
			pins = "gpio22";
			function = "gpio";
		};

		config {
			pins = "gpio22";
			drive-strength = <2>;
			output-low;
		};
	};
};

&qupv3_hub_i2c2 {
	status = "ok";
	#include "kalama-moto-common-redriver.dtsi"
};

&usb0 {
	ssusb_redriver = <&redriver>;
};

&pm8550b_eusb2_repeater {
	qcom,host-param-override-seq =
		/* <value reg_offset> */
		/* Adjust HS trasmit amplitude */
		<0xa 0x51
		/* HS disconnect threshold */
		 0x6 0x53
		/* Squelch detection threshold */
		 0x5 0x54
		/* Tx pre-emphasis tuning */
		 0x6 0x57>;
};

&apps_rsc_drv2 {
	rpmh-regulator-ldob4 {
		compatible = "qcom,rpmh-vrm-regulator";
		qcom,resource-name = "ldob4";
		qcom,regulator-type = "pmic5-ldo";
		qcom,supported-modes =
			<RPMH_REGULATOR_MODE_LPM
			RPMH_REGULATOR_MODE_HPM>;
		qcom,mode-threshold-currents = <0 10000>;

		L4B: pm_humu_l4: regulator-pm-humu-l4 {
			regulator-name = "pm_humu_l4";
			qcom,set = <RPMH_REGULATOR_SET_ALL>;
			regulator-min-microvolt = <1800000>;
			regulator-max-microvolt = <1800000>;
			qcom,init-voltage = <1800000>;
			qcom,init-mode = <RPMH_REGULATOR_MODE_HPM>;
		};
	};
};