&soc {
	ufs2phy_mem: ufsphy2_mem@1da7000 {
		compatible = "qcom,ufs-phy-qmp-v4-waipio";
		reg = <0x1da7000 0xe10>;
		reg-names = "phy_mem";
		#phy-cells = <0>;

		vdda-phy-supply = <&L4A>;
		vdda-pll-supply = <&L1C>;
		vdda-phy-max-microamp = <137000>;
		vdda-pll-max-microamp = <18300>;

		lanes-per-direction = <2>;
		clock-names = "ref_clk_src",
			"ref_clk",
			"ref_aux_clk";
		clocks = <&dummycc RPMH_CXO_CLK>,
			<&gcc GCC_EDP_REF_CLKREF_EN>,
			<&gcc GCC_UFS_CARD_PHY_AUX_CLK>;
		resets = <&ufshc2_mem 0>;
		status = "disabled";
	};

	ufshc2_mem: ufshc2@1da4000 {
		compatible = "qcom,ufshc";
		reg = <0x1da4000 0x3000>;
		reg-names = "ufs_mem";
		interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>;
		phys = <&ufs2phy_mem>;
		phy-names = "ufsphy";
		#reset-cells = <1>;

		vdd-hba-supply = <&gcc_ufs_card_gdsc>;
		vdd-hba-fixed-regulator;

		vcc-supply = <&L8C>;
		vcc-voltage-level = <2504000 2506000>;
		vcc-max-microamp = <1100000>;

		vccq-supply = <&L5C>;
		vccq-max-microamp = <1200000>;

		vccq2-supply = <&S4A>;
		vccq2-max-microamp = <800000>;

		qcom,vddp-ref-clk-supply = <&L5C>;
		qcom,vddp-ref-clk-max-microamp = <100>;

		lanes-per-direction = <2>;
		dev-ref-clk-freq = <0>; /* 19.2 MHz */

		clock-names =
			"core_clk",
			"bus_aggr_clk",
			"iface_clk",
			"core_clk_unipro",
			"core_clk_ice",
			"ref_clk",
			"tx_lane0_sync_clk",
			"rx_lane0_sync_clk",
			"rx_lane1_sync_clk";

		clocks =
			<&gcc GCC_UFS_CARD_AXI_CLK>,
			<&gcc GCC_AGGRE_UFS_CARD_AXI_CLK>,
			<&gcc GCC_UFS_CARD_AHB_CLK>,
			<&gcc GCC_UFS_CARD_UNIPRO_CORE_CLK>,
			<&gcc GCC_UFS_CARD_ICE_CORE_CLK>,
			<&dummycc RPMH_CXO_CLK>,
			<&gcc GCC_UFS_CARD_TX_SYMBOL_0_CLK>,
			<&gcc GCC_UFS_CARD_RX_SYMBOL_0_CLK>,
			<&gcc GCC_UFS_CARD_RX_SYMBOL_1_CLK>;

		freq-table-hz =
			<75000000 300000000>,
			<0 0>,
			<0 0>,
			<75000000 300000000>,
			<75000000 300000000>,
			<0 0>,
			<0 0>,
			<0 0>,
			<0 0>;

		qcom,ufs-bus-bw,name = "ufshc_mem";
		qcom,ufs-bus-bw,num-cases = <26>;
		qcom,ufs-bus-bw,num-paths = <2>;
		qcom,ufs-bus-bw,vectors-KBps =
		/*
		 * During HS G3 UFS runs at nominal voltage corner, vote
		 * higher bandwidth to push other buses in the data path
		 * to run at nominal to achieve max throughput.
		 * 4GBps pushes BIMC to run at nominal.
		 * 200MBps pushes CNOC to run at nominal.
		 * Vote for half of this bandwidth for HS G3 1-lane.
		 * For max bandwidth, vote high enough to push the buses
		 * to run in turbo voltage corner.
		 */
		<0 0>, <0 0>,          /* No vote */
		<922 0>, <1000 0>,     /* PWM G1 */
		<1844 0>, <1000 0>,    /* PWM G2 */
		<3688 0>, <1000 0>,    /* PWM G3 */
		<7376 0>, <1000 0>,    /* PWM G4 */
		<1844 0>, <1000 0>,    /* PWM G1 L2 */
		<3688 0>, <1000 0>,    /* PWM G2 L2 */
		<7376 0>, <1000 0>,    /* PWM G3 L2 */
		<14752 0>, <1000 0>,   /* PWM G4 L2 */
		<127796 0>, <1000 0>,  /* HS G1 RA */
		<255591 0>, <1000 0>,  /* HS G2 RA */
		<1492582 0>, <102400 0>,  /* HS G3 RA */
		<2915200 0>, <204800 0>,  /* HS G4 RA */
		<255591 0>, <1000 0>,  /* HS G1 RA L2 */
		<511181 0>, <1000 0>,  /* HS G2 RA L2 */
		<1492582 0>, <204800 0>, /* HS G3 RA L2 */
		<2915200 0>, <409600 0>, /* HS G4 RA L2 */
		<149422 0>, <1000 0>,  /* HS G1 RB */
		<298189 0>, <1000 0>,  /* HS G2 RB */
		<1492582 0>, <102400 0>,  /* HS G3 RB */
		<2915200 0>, <204800 0>,  /* HS G4 RB */
		<298189 0>, <1000 0>,  /* HS G1 RB L2 */
		<596378 0>, <1000 0>,  /* HS G2 RB L2 */
		/* As UFS working in HS G3 RB L2 mode, aggregated
		 * bandwidth (AB) should take care of providing
		 * optimum throughput requested. However, as tested,
		 * in order to scale up CNOC clock, instantaneous
		 * bindwidth (IB) needs to be given a proper value too.
		 */
		<1492582 0>, <204800 409600>, /* HS G3 RB L2 KBPs */
		<2915200 0>, <409600 409600>, /* HS G4 RB L2 */
		<7643136 0>, <307200 0>; /* Max. bandwidth */

		qcom,bus-vector-names = "MIN",
		"PWM_G1_L1", "PWM_G2_L1", "PWM_G3_L1", "PWM_G4_L1",
		"PWM_G1_L2", "PWM_G2_L2", "PWM_G3_L2", "PWM_G4_L2",
		"HS_RA_G1_L1", "HS_RA_G2_L1", "HS_RA_G3_L1", "HS_RA_G4_L1",
		"HS_RA_G1_L2", "HS_RA_G2_L2", "HS_RA_G3_L2", "HS_RA_G4_L2",
		"HS_RB_G1_L1", "HS_RB_G2_L1", "HS_RB_G3_L1", "HS_RB_G4_L1",
		"HS_RB_G1_L2", "HS_RB_G2_L2", "HS_RB_G3_L2", "HS_RB_G4_L2",
		"MAX";

		reset-gpios = <&tlmm 150 GPIO_ACTIVE_LOW>;

		resets = <&gcc GCC_UFS_CARD_BCR>;
		reset-names = "rst";
		iommus = <&apps_smmu 0x420 0x0>;
		qcom,iommu-dma = "fastmap";
		dma-coherent;

		status = "disabled";

		qos0 {
			mask = <0xf0>;
			vote = <44>;
		};

		qos1 {
			mask = <0x0f>;
			vote = <44>;
		};

	};
};