Qualcomm Technologies, Inc. SMBLITE Charger Specific Bindings

SMBLITE Charger is an efficient programmable battery charger capable of charging a
lithium-ion battery over micro-USB or USB Type-C.

=======================
Required Node Structure
=======================

SMBLITE Charger must be described in two levels of devices nodes.

===================================
First Level Node - SMBLITE Charger
===================================

Charger specific properties:
- compatible
  Usage:      required
  Value type: <string>
  Definition: "qcom,qpnp-smblite" for SMBLITE on PM2250.
	      "qcom,qpnp-pm5100-smblite" for SMBLITE on PM5100.

- qcom,pmic-revid
  Usage:      required
  Value type: phandle
  Definition: Should specify the phandle of PMI's revid module. This is used to
		identify the PMI subtype.

- io-channels
- io-channel-names
  Usage:      optional
  Value type: <phandle>
  Definition: For details about IIO bindings see:
		Documentation/devicetree/bindings/iio/iio-bindings.txt

- qcom,batteryless-platform
  Usage:      optional
  Value type: <empty>
  Definition: Boolean flag which indicates that the platform does not have a
		battery, and therefore charging should be disabled. In
		addition battery properties will be faked such that the device
		assumes normal operation.

- qcom,fcc-max-ua
  Usage:      optional
  Value type: <u32>
  Definition: Specifies the maximum fast charge current in micro-amps in
		battery profile.
		If the value is not present, 1Amp is used as default.

- qcom,fv-max-uv
  Usage:      optional
  Value type: <u32>
  Definition: Specifies the maximum float voltage in micro-volts in
		battery profile.
		If the value is not present, 4.35V is used as default.

- qcom,usb-icl-ua
  Usage:      optional
  Value type: <u32>
  Definition: Specifies the USB input current limit in micro-amps.
		 If the value is not present, 1.5Amps is used as default.

- qcom,thermal-mitigation
  Usage:      optional
  Value type: Array of <u32>
  Definition: Array of fast charge current limit values for
		different system thermal mitigation levels.
		This should be a flat array that denotes the
		maximum charge current in mA for each thermal
		level.

- qcom,chg-inhibit-threshold-mv
  Usage:      optional
  Value type: <u32>
  Definition: Charge inhibit threshold in milli-volts. Charging will be
		inhibited when the battery voltage is within this threshold
		from Vfloat at charger insertion. If this is not specified
		then charge inhibit will be disabled by default.
		Allowed values are: 50, 100, 200, 300.

- qcom,chg-term-src
  Usage:      optional
  Value type: <u32>
  Definition: Specify either the ADC or analog comparators to be used in order
		to set threshold values for charge termination current.
		0 - Unspecified
		1 - Select ADC comparator
		2 - Select ANALOG comparator

- qcom,chg-term-current-ma
  Usage:      optional
  Value type: <u32>
  Definition: When ADC comparator is selected as qcom,chg-term-src, this
		parameter should be set to the desired upper threshold.

- qcom,chg-term-base-current-ma
  Usage:      optional
  Value type: <u32>
  Definition: When ADC comparator is selected as qcom,chg-term-src, this
		parameter should be set to the desired lower threshold.

- qcom,auto-recharge-soc
  Usage:      optional
  Value type: <u32>
  Definition: Specifies the SOC threshold at which the charger will
		restart charging after termination. The value specified
		ranges from 0 - 100. The feature is enabled if this
		property is specified with a valid SOC value.

- qcom,auto-recharge-vbat-mv
  Usage:      optional
  Value type: <u32>
  Definition: Specifies the battery voltage threshold at which the charger
		will restart charging after termination. The value specified
		is in milli-volts.

- qcom,suspend-input-on-debug-batt
  Usage:      optional
  Value type: <empty>
  Definition: Boolean flag which when present enables input suspend for
		debug battery.

- qcom,fake-chg-status-on-debug-batt
  Usage:      optional
  Value type: <empty>
  Definition: Boolean flag which when present shows charging status as
		unknown for debug battery. This needs to be specified only if
		the device needs to be kept powered on always with
		"svc power stayon true".

- qcom,typec-legacy-rp-icl
  Usage:       optional
  Value type:  bool
  Definition:  Boolean property to enable setting ICL based on Rp for
		Type-C non-compliant legacy cables.

- qcom,wd-bark-time-secs
  Usage:      optional
  Value type: <u32>
  Definition: WD bark-timeout in seconds. The possible values are
		16, 32, 64, 128. If not defined it defaults to 64.

- qcom,battery-data
  Usage:      optional
  Value type: <phandle>
  Definition: Specifies the phandle of the node which contains the battery
		profiles supported on the device.

- qcom,flash-derating-soc
  Usage:      optional
  Value type: <u32>
  Definition: SOC threshold in percentage below which hardware will start
		derating flash. This is only applicable to certain PMICs like
		PMI632 which has SCHGM_FLASH peripheral.

- qcom,flash-disable-soc
  Usage:      optional
  Value type: <u32>
  Definition: SOC threshold in percentage below which hardware will disable
		flash. This is only applicable to certain PMICs like PMI632
		which has SCHGM_FLASH peripheral.

- qcom,headroom-mode
  Usage:      optional
  Value type: <u32>
  Definition: Specifies flash hardware headroom management policy. The
		possible values are:
		<0>: Fixed mode, constant 5V at flash input.
		<1>: Adaptive mode allows charger output voltage to be
		dynamically controlled by the flash module based on the
		required flash headroom.
		This is only applicable to certain PMICs like PMI632 which
		has SCHGM_FLASH peripheral.

- nvmem-cell-names
  Usage:      optional
  Value type: <string>
  Definition: The nvmem cell device name of the SDAM register used to store
		the charger debug mask. It must be "charger_debug_mask".

- nvmem-cells
  Usage:      optional
  Value type: <phandle>
  Definition: Phandle of the nvmem cell device used to store the charger debug
		mask. Please refer to nvmem bindings as described in
		bindings/nvmem/nvmem.txt.

- qcom,fcc-stepping-enable
  Usage:      optional
  Value type: bool
  Definition: Boolean flag which when present enables stepwise change in FCC.
		The default stepping rate is 100mA/sec.

- qcom,disable-suspend-on-collapse
  Usage:      optional
  Value type: bool
  Definition: Boolean flag which when present disables suspend on collapse
		feature of charger hardware.

- qcom,fcc-step-delay-ms
  Usage:      optional
  Value type: <u32>
  Definition: Specifies the delay between each step of FCC stepper algorithm.
		If left unspecified, the default value is 1 Sec.

- qcom,fcc-step-size-ua
  Usage:      optional
  Value type: <u32>
  Definition: Specifies the step size of each step of FCC stepper algorithm.
		If left unspecified, the default value is 100mA.

- qcom,fc-step-start-ua
  Usage:     optional
  Value type: <u32>
  Definition: Specifies the initial current of FCC stepper algorithm.
		If left unspecified, the default value is 500mA.

- qcom,concurrency-mode-enable
 Usage:      optional
 Value type: bool
 Definition: Boolean flag to control charger concurrency mode. Its supported
		only on PM5100, By default this feature is disabled.

- qcom,remote-fg
 Usage:      optional
 Value type: bool
 Definition: Boolean flag to determine if FG is running on different processor.
		Its supported only on PM5100, By default this feature is disabled.

- qcom,float-option
  Usage:      optional
  Value type: <u32>
  Definition: Configures how the charger behaves when a float charger is
	      detected by APSD.
	        1 - Treat as a DCP.
	        2 - Treat as a SDP.
	        3 - Disable charging.
	        4 - Suspend USB input.

- qcom,uusb-ss-mode-extcon-enable
 Usage:      optional
 Value type: bool
 Definition: Boolean flag to support board designs with Micro-AB 3.0 USB port.
	     If this is enabled, on USB plugin event SS mode extcon notification
	     is sent  (instead of an HS mode). This DT property should be defined
	     only if the board is not expected to support Micro-B type USB cable
	     on the Micro-AB 3.0 port, as the Micro-B cable cannot support SS mode.
	     By default this feature is disabled.

=================================================
Second Level Nodes - SMBLITE Charger Peripherals
=================================================

Peripheral specific properties:
- reg
  Usage:      required
  Value type: <prop-encoded-array>
  Definition: Address and size of the peripheral's register block.

- interrupts
  Usage:      required
  Value type: <prop-encoded-array>
  Definition: Peripheral interrupt specifier.

- interrupt-names
  Usage:      required
  Value type: <stringlist>
  Definition: Interrupt names.  This list must match up 1-to-1 with the
	      interrupts specified in the 'interrupts' property.

=======
Example
=======

pm2250_charger: qcom,qpnp-smblite {
	compatible = "qcom,qpnp-smblite";
	#address-cells = <1>;
	#size-cells = <1>;
	#cooling-cells = <2>;

	nvmem-cell-names = "charger_debug_mask";
	nvmem-cells = <&charger_debug_mask>;

	qcom,pmic-revid = <&pm2250_revid>;
	qcom,chgr@1000 {
		reg = <0x1000 0x100>;
		interrupts =
			<0x0 0x10 0x1 IRQ_TYPE_EDGE_RISING>,
			<0x0 0x10 0x0 IRQ_TYPE_EDGE_RISING>,
			<0x0 0x10 0x4 IRQ_TYPE_EDGE_RISING>,
			<0x0 0x10 0x7 IRQ_TYPE_EDGE_RISING>;

		interrupt-names = "chgr-error",
			"chg-state-change",
			"buck-oc",
			"vph-ov";
	};

	qcom,dcdc@1100 {
		reg = <0x1100 0x100>;
		interrupts =
			<0x0 0x11 0x0 IRQ_TYPE_EDGE_RISING>,
			<0x0 0x11 0x1 IRQ_TYPE_EDGE_RISING>,
			<0x0 0x11 0x2 IRQ_TYPE_EDGE_RISING>,
			<0x0 0x11 0x6 IRQ_TYPE_EDGE_RISING>,
			<0x0 0x11 0x7 IRQ_TYPE_EDGE_BOTH>;

		interrupt-names = "otg-fail",
			"otg-fault",
			"skip-mode",
			"input-current-limiting",
			"switcher-power-ok";
	};

	qcom,batif@1200 {
		reg = <0x1200 0x100>;
		interrupts =
			<0x0 0x12 0x0 IRQ_TYPE_EDGE_BOTH>,
			<0x0 0x12 0x1 IRQ_TYPE_EDGE_BOTH>,
			<0x0 0x12 0x2 IRQ_TYPE_EDGE_BOTH>,
			<0x0 0x12 0x3 IRQ_TYPE_EDGE_BOTH>,
			<0x0 0x12 0x4 IRQ_TYPE_EDGE_RISING>;

		interrupt-names = "bat-temp",
			"bat-therm-or-id-missing",
			"bat-low",
			"bat-ov",
			"bsm-active";
	};

	qcom,usb@1300 {
		reg = <0x1300 0x100>;
		interrupts =
			<0x0 0x13 0x0 IRQ_TYPE_EDGE_BOTH>,
			<0x0 0x13 0x1 IRQ_TYPE_EDGE_BOTH>,
			<0x0 0x13 0x2 IRQ_TYPE_EDGE_BOTH>,
			<0x0 0x13 0x3 IRQ_TYPE_EDGE_BOTH>,
			<0x0 0x13 0x4 IRQ_TYPE_EDGE_RISING>,
			<0x0 0x13 0x6 IRQ_TYPE_EDGE_RISING>;

		interrupt-names = "usbin-plugin",
			"usbin-collapse",
			"usbin-uv",
			"usbin-ov",
			"usbin-gtvt",
			"usbin-icl-change";
	};

	qcom,typec@1500 {
		reg = <0x1500 0x100>;
		interrupts =
			<0x0 0x15 0x0 IRQ_TYPE_EDGE_BOTH>,
			<0x0 0x15 0x1 IRQ_TYPE_EDGE_BOTH>,
			<0x0 0x15 0x2 IRQ_TYPE_EDGE_RISING>,
			<0x0 0x15 0x4 IRQ_TYPE_EDGE_BOTH>,
			<0x0 0x15 0x5 IRQ_TYPE_EDGE_RISING>,
			<0x0 0x15 0x6 IRQ_TYPE_EDGE_RISING>,
			<0x0 0x15 0x7 IRQ_TYPE_EDGE_RISING>;

		interrupt-names = "typec-or-rid-detect-change",
			"typec-vpd-detect",
			"typec-cc-state-change",
			"typec-vbus-change",
			"typec-attach-detach",
			"typec-legacy-cable-detect",
			"typec-try-snk-src-detect";
	};

	qcom,misc@1600 {
		reg = <0x1600 0x100>;
		interrupts =
			<0x0 0x16 0x0 IRQ_TYPE_EDGE_RISING>,
			<0x0 0x16 0x1 IRQ_TYPE_EDGE_RISING>,
			<0x0 0x16 0x2 IRQ_TYPE_EDGE_RISING>,
			<0x0 0x16 0x3 IRQ_TYPE_EDGE_RISING>,
			<0x0 0x16 0x4 IRQ_TYPE_EDGE_RISING>,
			<0x0 0x16 0x5 IRQ_TYPE_EDGE_RISING>,
			<0x0 0x16 0x6 IRQ_TYPE_EDGE_BOTH>;

		interrupt-names = "wdog-snarl",
			"wdog-bark",
			"aicl-fail",
			"aicl-done",
			"imp-trigger",
			"all-chnl-cond-done",
			"temp-change";
	};
};