194 lines
3.7 KiB
Text
194 lines
3.7 KiB
Text
/* Copyright (c) 2021, The Linux Foundation. All rights reserved.
|
|
*
|
|
* This program is free software; you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License version 2 and
|
|
* only version 2 as published by the Free Software Foundation.
|
|
*
|
|
* This program is distributed in the hope that it will be useful,
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
* GNU General Public License for more details.
|
|
*/
|
|
|
|
/* This file is only for rtwo device */
|
|
|
|
#include "crow-eqe-products-common-overlay.dtsi"
|
|
#include "crow-eqe-fingerprint-overlay.dtsi"
|
|
#include "crow-eqe-sensors-overlay.dtsi"
|
|
#include "crow-moto-common-st-nfc.dtsi"
|
|
#include "crow-moto-common-charger.dtsi"
|
|
#include "crow-eqe-charger-overlay.dtsi"
|
|
#include "crow-eqe-thermal-overlay.dtsi"
|
|
#include "moto-eqe-external-camera-pmic.dtsi"
|
|
|
|
&soc {
|
|
mmi_relay {
|
|
compatible = "mmi,sys-relay";
|
|
};
|
|
|
|
};
|
|
|
|
&qseecom_mem {
|
|
size = <0x0 0x1800000>;
|
|
};
|
|
|
|
&qseecom_ta_mem {
|
|
size = <0x0 0x2000000>;
|
|
};
|
|
|
|
&tlmm {
|
|
/* reserve FP GPIOs: gpio12,13,14,15 24 25 26 27 for NFC 111 112 for WLAN*/
|
|
qcom,gpios-reserved = <12 13 14 15 24 25 26 27 111 112>;
|
|
|
|
redriver_enable: redriver_enable {
|
|
mux {
|
|
pins = "gpio55";
|
|
function = "gpio";
|
|
};
|
|
|
|
config {
|
|
pins = "gpio55";
|
|
drive-strength = <2>;
|
|
bias-disable; /* NO PULL */
|
|
output-high;
|
|
};
|
|
};
|
|
redriver_disable: redriver_disable {
|
|
mux {
|
|
pins = "gpio55";
|
|
function = "gpio";
|
|
};
|
|
|
|
config {
|
|
pins = "gpio55";
|
|
drive-strength = <2>;
|
|
output-low;
|
|
};
|
|
};
|
|
};
|
|
|
|
&usb0 {
|
|
ssusb_redriver = <&redriver>;
|
|
};
|
|
|
|
&qupv3_se8_i2c {
|
|
status = "ok";
|
|
redriver:redriver@30{
|
|
compatible = "parade,ps5169-redriver";
|
|
reg = <0x30>;
|
|
vcc-supply = <&L7B>;
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&redriver_enable>;
|
|
redriver,enable-gpio = <&tlmm 55 0x00>;
|
|
redriver,orientation-gpio = <&tlmm 83 0x00>;
|
|
config-seq =
|
|
/* <reg_offset, value, delay_us> */
|
|
<0x9d 0x80 10000
|
|
0x9d 0x00 0
|
|
0x40 0x80 0
|
|
0x8d 0x01 0
|
|
0x90 0x01 0
|
|
0x51 0x87 0
|
|
0x50 0x20 0
|
|
0x54 0x11 0
|
|
0x5d 0x66 0
|
|
0x52 0x50 0
|
|
0x55 0x00 0
|
|
0x56 0x00 0
|
|
0x57 0x00 0
|
|
0x58 0x00 0
|
|
0x59 0x00 0
|
|
0x5a 0x00 0
|
|
0x5b 0x00 0
|
|
0x5e 0x07 0
|
|
0x5f 0x00 0
|
|
0x60 0x00 0
|
|
0x61 0x03 0
|
|
0x65 0x40 0
|
|
0x66 0x00 0
|
|
0x67 0x03 0
|
|
0x75 0x0c 0
|
|
0x77 0x00 0
|
|
0x78 0x7c 0>;
|
|
};
|
|
};
|
|
|
|
&L16B {
|
|
regulator-min-microvolt = <3000000>;
|
|
regulator-max-microvolt = <3000000>;
|
|
qcom,init-voltage = <3000000>;
|
|
regulator-boot-on;
|
|
regulator-always-on;
|
|
};
|
|
|
|
&tlmm {
|
|
laser_xsdn_active: laser_xsdn_active {
|
|
mux {
|
|
pins = "gpio131";
|
|
function = "gpio";
|
|
};
|
|
|
|
config {
|
|
pins = "gpio131";
|
|
drive-strength = <2>;
|
|
bias-disable;
|
|
};
|
|
};
|
|
|
|
laser_xsdn_suspend: laser_xsdn_suspend {
|
|
mux {
|
|
pins = "gpio131";
|
|
function = "gpio";
|
|
};
|
|
|
|
config {
|
|
pins = "gpio131";
|
|
drive-strength = <2>;
|
|
bias-pull-down;
|
|
};
|
|
};
|
|
|
|
laser_int_active: laser_int_active {
|
|
mux {
|
|
pins = "gpio69";
|
|
function = "gpio";
|
|
};
|
|
|
|
config {
|
|
pins = "gpio69";
|
|
drive-strength = <2>;
|
|
bias-pull-up;
|
|
};
|
|
};
|
|
|
|
laser_int_suspend: laser_int_suspend {
|
|
mux {
|
|
pins = "gpio69";
|
|
function = "gpio";
|
|
};
|
|
|
|
config {
|
|
pins = "gpio69";
|
|
drive-strength = <2>;
|
|
bias-pull-down;
|
|
};
|
|
};
|
|
};
|
|
|
|
&qupv3_se1_i2c {
|
|
status = "okay";
|
|
qcom,noise-rjct-scl = <3>;
|
|
qcom,noise-rjct-sda = <3>;
|
|
stmvl53l1@29 {
|
|
status = "ok";
|
|
compatible = "st,stmvl53l1";
|
|
reg = <0x29>;
|
|
vdd-vl53l1-supply = <&L16B>;
|
|
gpios = <&tlmm 131 0>, <&tlmm 69 0>;
|
|
pinctrl-names = "laser_default", "laser_suspend";
|
|
pinctrl-0 = <&laser_xsdn_active &laser_int_active>;
|
|
pinctrl-1 = <&laser_xsdn_suspend &laser_int_suspend>;
|
|
st,sensorthreshold = <60 65>;
|
|
st,xtalkval = <0x0 0x0 0x0>;
|
|
};
|
|
};
|