83 lines
1.7 KiB
Text
83 lines
1.7 KiB
Text
#include <dt-bindings/interrupt-controller/irq.h>
|
|
#include <dt-bindings/spmi/spmi.h>
|
|
|
|
&spmi_bus {
|
|
#address-cells = <2>;
|
|
#size-cells = <0>;
|
|
interrupt-controller;
|
|
#interrupt-cells = <4>;
|
|
|
|
qcom,pmx75@1 {
|
|
compatible = "qcom,spmi-pmic";
|
|
reg = <1 SPMI_USID>;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
pmx75_tz: qcom,temp-alarm@a00 {
|
|
compatible = "qcom,spmi-temp-alarm";
|
|
reg = <0xa00>;
|
|
interrupts = <0x1 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
|
|
#thermal-sensor-cells = <0>;
|
|
};
|
|
|
|
pmx75_vbus_detect: qcom,pmd-vbus-det@1500 {
|
|
compatible = "qcom,pm8941-misc";
|
|
reg = <0x1500>;
|
|
interrupts = <0x1 0x15 0x0 IRQ_TYPE_EDGE_BOTH>;
|
|
interrupt-names = "usb_vbus";
|
|
status = "disabled";
|
|
};
|
|
|
|
pmx75_gpios: pinctrl@8800 {
|
|
compatible = "qcom,pmx75-gpio";
|
|
reg = <0x8800>;
|
|
gpio-controller;
|
|
#gpio-cells = <2>;
|
|
interrupt-controller;
|
|
#interrupt-cells = <2>;
|
|
};
|
|
|
|
pmx75_pwm: pwms@e800 {
|
|
compatible = "qcom,pwm-lpg";
|
|
reg = <0xe800>;
|
|
reg-names = "lpg-base";
|
|
#pwm-cells = <2>;
|
|
qcom,num-lpg-channels = <4>;
|
|
};
|
|
|
|
pmx75_eusb2_repeater: qcom,eusb2-repeater@fd00 {
|
|
compatible = "qcom,pmic-eusb2-repeater";
|
|
reg = <0xfd00>;
|
|
status = "disabled";
|
|
};
|
|
};
|
|
};
|
|
|
|
&thermal_zones {
|
|
pmx75_temp_alarm: pmx75_tz {
|
|
polling-delay-passive = <100>;
|
|
polling-delay = <0>;
|
|
thermal-governor = "step_wise";
|
|
thermal-sensors = <&pmx75_tz>;
|
|
|
|
trips {
|
|
pmx75_trip0: trip0 {
|
|
temperature = <95000>;
|
|
hysteresis = <0>;
|
|
type = "passive";
|
|
};
|
|
|
|
pmx75_trip1: trip1 {
|
|
temperature = <115000>;
|
|
hysteresis = <0>;
|
|
type = "critical";
|
|
};
|
|
|
|
pmx75_trip2: trip2 {
|
|
temperature = <145000>;
|
|
hysteresis = <0>;
|
|
type = "critical";
|
|
};
|
|
};
|
|
};
|
|
};
|