183 lines
3.9 KiB
Text
183 lines
3.9 KiB
Text
#include <dt-bindings/input/input.h>
|
|
#include <dt-bindings/input/qcom,qpnp-power-on.h>
|
|
#include <dt-bindings/interrupt-controller/irq.h>
|
|
#include <dt-bindings/spmi/spmi.h>
|
|
#include <dt-bindings/iio/qcom,spmi-vadc.h>
|
|
|
|
&spmi_bus {
|
|
qcom,pm6125@0 {
|
|
compatible = "qcom,spmi-pmic";
|
|
reg = <0x0 0x0>;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
pm6125_revid: qcom,revid@100 {
|
|
compatible = "qcom,qpnp-revid";
|
|
reg = <0x100>;
|
|
};
|
|
|
|
qcom,power-on@800 {
|
|
compatible = "qcom,qpnp-power-on";
|
|
reg = <0x800>;
|
|
interrupts = <0x0 0x8 0x0 IRQ_TYPE_EDGE_BOTH>,
|
|
<0x0 0x8 0x1 IRQ_TYPE_EDGE_BOTH>;
|
|
interrupt-names = "kpdpwr", "resin";
|
|
qcom,pon-dbc-delay = <15625>;
|
|
qcom,kpdpwr-sw-debounce;
|
|
qcom,system-reset;
|
|
qcom,store-hard-reset-reason;
|
|
|
|
qcom,pon_1 {
|
|
qcom,pon-type = <PON_POWER_ON_TYPE_KPDPWR>;
|
|
qcom,pull-up = <1>;
|
|
linux,code = <KEY_POWER>;
|
|
};
|
|
|
|
qcom,pon_2 {
|
|
qcom,pon-type = <PON_POWER_ON_TYPE_RESIN>;
|
|
qcom,pull-up = <1>;
|
|
linux,code = <KEY_VOLUMEDOWN>;
|
|
};
|
|
};
|
|
|
|
pm6125_vadc: vadc@3100 {
|
|
compatible = "qcom,spmi-adc5";
|
|
reg = <0x3100>;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
|
|
interrupt-names = "eoc-int-en-set";
|
|
qcom,adc-vdd-reference = <1875>;
|
|
#io-channel-cells = <1>;
|
|
io-channel-ranges;
|
|
|
|
/* Channel nodes */
|
|
ref_gnd {
|
|
reg = <ADC5_REF_GND>;
|
|
label = "ref_gnd";
|
|
qcom,pre-scaling = <1 1>;
|
|
};
|
|
|
|
vref_1p25 {
|
|
reg = <ADC5_1P25VREF>;
|
|
label = "vref_1p25";
|
|
qcom,pre-scaling = <1 1>;
|
|
};
|
|
|
|
die_temp {
|
|
reg = <ADC5_DIE_TEMP>;
|
|
label = "die_temp";
|
|
qcom,pre-scaling = <1 1>;
|
|
};
|
|
|
|
vph_pwr {
|
|
reg = <ADC5_VPH_PWR>;
|
|
label = "vph_pwr";
|
|
qcom,pre-scaling = <1 3>;
|
|
};
|
|
|
|
xo_therm {
|
|
reg = <ADC5_XO_THERM_100K_PU>;
|
|
label = "xo_therm";
|
|
qcom,ratiometric;
|
|
qcom,hw-settle-time = <200>;
|
|
qcom,pre-scaling = <1 1>;
|
|
};
|
|
};
|
|
|
|
pm6125_adc_tm: adc_tm@3500 {
|
|
compatible = "qcom,spmi-adc-tm5";
|
|
reg = <0x3500>;
|
|
interrupts = <0x0 0x35 0x0 IRQ_TYPE_EDGE_RISING>;
|
|
interrupt-names = "pm-adc-tm5";
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
#thermal-sensor-cells = <1>;
|
|
};
|
|
|
|
pm6125_misc: qcom,misc@900 {
|
|
compatible = "qcom,qpnp-misc";
|
|
reg = <0x900>;
|
|
};
|
|
|
|
pm6125_tz: qcom,temp-alarm@2400 {
|
|
compatible = "qcom,spmi-temp-alarm";
|
|
reg = <0x2400>;
|
|
interrupts = <0x0 0x24 0x0 IRQ_TYPE_EDGE_BOTH>;
|
|
#thermal-sensor-cells = <0>;
|
|
qcom,temperature-threshold-set = <1>;
|
|
};
|
|
|
|
pm6125_clkdiv: clock-controller@5b00 {
|
|
compatible = "qcom,spmi-clkdiv";
|
|
reg = <0x5b00>;
|
|
#clock-cells = <1>;
|
|
qcom,num-clkdivs = <1>;
|
|
clock-output-names = "pm6125_div_clk1";
|
|
clocks = <&rpmcc RPM_SMD_XO_CLK_SRC>;
|
|
clock-names = "xo";
|
|
assigned-clocks = <&pm6125_clkdiv 1>;
|
|
assigned-clock-rates = <9600000>;
|
|
};
|
|
|
|
pm6125_gpios: pinctrl@c000 {
|
|
compatible = "qcom,pm6125-gpio";
|
|
reg = <0xc000>;
|
|
gpio-controller;
|
|
#gpio-cells = <2>;
|
|
interrupt-controller;
|
|
#interrupt-cells = <2>;
|
|
};
|
|
|
|
pm6125_rtc: qcom,pm6125_rtc {
|
|
compatible = "qcom,pm8941-rtc";
|
|
interrupts = <0x0 0x61 0x1 IRQ_TYPE_NONE>;
|
|
};
|
|
};
|
|
|
|
qcom,pm6125@1 {
|
|
compatible ="qcom,spmi-pmic";
|
|
reg = <0x1 0x0>;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
pm6125_pwm: qcom,pwms@b300 {
|
|
status = "disabled";
|
|
compatible = "qcom,pwm-lpg";
|
|
reg = <0xb300>;
|
|
reg-names = "lpg-base";
|
|
qcom,num-lpg-channels = <1>;
|
|
#pwm-cells = <2>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&thermal_zones {
|
|
pm6125-tz {
|
|
polling-delay-passive = <100>;
|
|
polling-delay = <0>;
|
|
thermal-governor = "step_wise";
|
|
thermal-sensors = <&pm6125_tz>;
|
|
wake-capable-sensor;
|
|
|
|
trips {
|
|
pm6125_trip0: trip0 {
|
|
temperature = <95000>;
|
|
hysteresis = <0>;
|
|
type = "passive";
|
|
};
|
|
|
|
pm6125_trip1: trip1 {
|
|
temperature = <115000>;
|
|
hysteresis = <0>;
|
|
type = "passive";
|
|
};
|
|
|
|
trip2 {
|
|
temperature = <145000>;
|
|
hysteresis = <0>;
|
|
type = "passive";
|
|
};
|
|
};
|
|
};
|
|
};
|