pinctrl: add abx500 pinctrl driver core

This adds the AB8500 core driver, which will be utilized by
the follow-on drivers for different ABx500 variants.
Sselect the driver from the DBX500_SOC, as this chip is
powering and clocking that SoC.

Cc: Samuel Ortiz <[email protected]>
Signed-off-by: Patrice Chotard <[email protected]>
Signed-off-by: Linus Walleij <[email protected]>

drivers/pinctrl/Kconfig

@@ -26,6 +26,13 @@ config DEBUG_PINCTRL
 	help
 	  Say Y here to add some extra checks and diagnostics to PINCTRL calls.
 
+config PINCTRL_ABX500
+	bool "ST-Ericsson ABx500 family Mixed Signal Circuit gpio functions"
+	depends on AB8500_CORE
+	select GENERIC_PINCONF
+	help
+	  Select this to enable the ABx500 family IC GPIO driver
+
 config PINCTRL_AT91
 	bool "AT91 pinctrl driver"
 	depends on OF

drivers/pinctrl/Makefile

@@ -9,6 +9,7 @@ ifeq ($(CONFIG_OF),y)
 obj-$(CONFIG_PINCTRL)		+= devicetree.o
 endif
 obj-$(CONFIG_GENERIC_PINCONF)	+= pinconf-generic.o
+obj-$(CONFIG_PINCTRL_ABX500)	+= pinctrl-abx500.o
 obj-$(CONFIG_PINCTRL_AT91)	+= pinctrl-at91.o
 obj-$(CONFIG_PINCTRL_BCM2835)	+= pinctrl-bcm2835.o
 obj-$(CONFIG_PINCTRL_IMX)	+= pinctrl-imx.o

drivers/pinctrl/pinctrl-abx500.h

@@ -0,0 +1,180 @@
+#ifndef PINCTRL_PINCTRL_ABx5O0_H
+#define PINCTRL_PINCTRL_ABx500_H
+
+/* Package definitions */
+#define PINCTRL_AB8500	0
+#define PINCTRL_AB8540	1
+#define PINCTRL_AB9540	2
+#define PINCTRL_AB8505	3
+
+/* pins alternate function */
+enum abx500_pin_func {
+	ABX500_DEFAULT,
+	ABX500_ALT_A,
+	ABX500_ALT_B,
+	ABX500_ALT_C,
+};
+
+/**
+ * struct abx500_function - ABx500 pinctrl mux function
+ * @name: The name of the function, exported to pinctrl core.
+ * @groups: An array of pin groups that may select this function.
+ * @ngroups: The number of entries in @groups.
+ */
+struct abx500_function {
+	const char *name;
+	const char * const *groups;
+	unsigned ngroups;
+};
+
+/**
+ * struct abx500_pingroup - describes a ABx500 pin group
+ * @name: the name of this specific pin group
+ * @pins: an array of discrete physical pins used in this group, taken
+ *	from the driver-local pin enumeration space
+ * @num_pins: the number of pins in this group array, i.e. the number of
+ *	elements in .pins so we can iterate over that array
+ * @altsetting: the altsetting to apply to all pins in this group to
+ *	configure them to be used by a function
+ */
+struct abx500_pingroup {
+	const char *name;
+	const unsigned int *pins;
+	const unsigned npins;
+	int altsetting;
+};
+
+#define ALTERNATE_FUNCTIONS(pin, sel_bit, alt1, alt2, alta, altb, altc)	\
+{									\
+	.pin_number = pin,						\
+	.gpiosel_bit = sel_bit,						\
+	.alt_bit1 = alt1,						\
+	.alt_bit2 = alt2,						\
+	.alta_val = alta,						\
+	.altb_val = altb,						\
+	.altc_val = altc,						\
+}
+
+#define UNUSED -1
+/**
+ * struct alternate_functions
+ * @pin_number:		The pin number
+ * @gpiosel_bit:	Control bit in GPIOSEL register,
+ * @alt_bit1:		First AlternateFunction bit used to select the
+ *			alternate function
+ * @alt_bit2:		Second AlternateFunction bit used to select the
+ *			alternate function
+ *
+ *			these 3 following fields are necessary due to none
+ *			coherency on how to select the altA, altB and altC
+ *			function between the ABx500 SOC family when using
+ *			alternatfunc register.
+ * @alta_val:		value to write in alternatfunc to select altA function
+ * @altb_val:		value to write in alternatfunc to select altB function
+ * @altc_val:		value to write in alternatfunc to select altC function
+ */
+struct alternate_functions {
+	unsigned pin_number;
+	s8 gpiosel_bit;
+	s8 alt_bit1;
+	s8 alt_bit2;
+	u8 alta_val;
+	u8 altb_val;
+	u8 altc_val;
+};
+
+/**
+ * struct pullud - specific pull up/down feature
+ * @first_pin:		The pin number of the first pins which support
+ *			specific pull up/down
+ * @last_pin:		The pin number of the last pins
+ */
+struct pullud {
+	unsigned first_pin;
+	unsigned last_pin;
+};
+
+#define GPIO_IRQ_CLUSTER(a, b, c)	\
+{					\
+	.start = a,			\
+	.end = b,			\
+	.offset = c,			\
+}
+
+/**
+ * struct abx500_gpio_irq_cluster - indicates GPIOs which are interrupt
+ *			capable
+ * @start:		The pin number of the first pin interrupt capable
+ * @end:		The pin number of the last pin interrupt capable
+ * @offset:		offset used to compute specific setting strategy of
+ *			the interrupt line
+ */
+
+struct abx500_gpio_irq_cluster {
+	int start;
+	int end;
+	int offset;
+};
+
+/**
+ * struct abx500_pinrange - map pin numbers to GPIO offsets
+ * @offset:		offset into the GPIO local numberspace, incidentally
+ *			identical to the offset into the local pin numberspace
+ * @npins:		number of pins to map from both offsets
+ * @altfunc:		altfunc setting to be used to enable GPIO on a pin in
+ *			this range (may vary)
+ */
+struct abx500_pinrange {
+	unsigned int offset;
+	unsigned int npins;
+	int altfunc;
+};
+
+#define ABX500_PINRANGE(a, b, c) { .offset = a, .npins = b, .altfunc = c }
+
+/**
+ * struct abx500_pinctrl_soc_data - ABx500 pin controller per-SoC configuration
+ * @gpio_ranges:	An array of GPIO ranges for this SoC
+ * @gpio_num_ranges:	The number of GPIO ranges for this SoC
+ * @pins:		An array describing all pins the pin controller affects.
+ *			All pins which are also GPIOs must be listed first within the
+ *			array, and be numbered identically to the GPIO controller's
+ *			numbering.
+ * @npins:		The number of entries in @pins.
+ * @functions:		The functions supported on this SoC.
+ * @nfunction:		The number of entries in @functions.
+ * @groups:		An array describing all pin groups the pin SoC supports.
+ * @ngroups:		The number of entries in @groups.
+ * @alternate_functions: array describing pins which supports alternate and
+ *			how to set it.
+ * @pullud:		array describing pins which supports pull up/down
+ *			specific registers.
+ * @gpio_irq_cluster:	An array of GPIO interrupt capable for this SoC
+ * @ngpio_irq_cluster:	The number of GPIO inetrrupt capable for this SoC
+ * @irq_gpio_rising_offset: Interrupt offset used as base to compute specific
+ *			setting strategy of the rising interrupt line
+ * @irq_gpio_falling_offset: Interrupt offset used as base to compute specific
+ *			setting strategy of the falling interrupt line
+ * @irq_gpio_factor:	Factor used to compute specific setting strategy of
+ *			the interrupt line
+ */
+
+struct abx500_pinctrl_soc_data {
+	const struct abx500_pinrange *gpio_ranges;
+	unsigned gpio_num_ranges;
+	const struct pinctrl_pin_desc *pins;
+	unsigned npins;
+	const struct abx500_function *functions;
+	unsigned nfunctions;
+	const struct abx500_pingroup *groups;
+	unsigned ngroups;
+	struct alternate_functions *alternate_functions;
+	struct pullud *pullud;
+	struct abx500_gpio_irq_cluster *gpio_irq_cluster;
+	unsigned ngpio_irq_cluster;
+	int irq_gpio_rising_offset;
+	int irq_gpio_falling_offset;
+	int irq_gpio_factor;
+};
+
+#endif /* PINCTRL_PINCTRL_ABx500_H */