Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6 into sh-latest

drivers/tty/Kconfig

@@ -0,0 +1,321 @@
+config VT
+	bool "Virtual terminal" if EXPERT
+	depends on !S390
+	select INPUT
+	default y
+	---help---
+	  If you say Y here, you will get support for terminal devices with
+	  display and keyboard devices. These are called "virtual" because you
+	  can run several virtual terminals (also called virtual consoles) on
+	  one physical terminal. This is rather useful, for example one
+	  virtual terminal can collect system messages and warnings, another
+	  one can be used for a text-mode user session, and a third could run
+	  an X session, all in parallel. Switching between virtual terminals
+	  is done with certain key combinations, usually Alt-<function key>.
+
+	  The setterm command ("man setterm") can be used to change the
+	  properties (such as colors or beeping) of a virtual terminal. The
+	  man page console_codes(4) ("man console_codes") contains the special
+	  character sequences that can be used to change those properties
+	  directly. The fonts used on virtual terminals can be changed with
+	  the setfont ("man setfont") command and the key bindings are defined
+	  with the loadkeys ("man loadkeys") command.
+
+	  You need at least one virtual terminal device in order to make use
+	  of your keyboard and monitor. Therefore, only people configuring an
+	  embedded system would want to say N here in order to save some
+	  memory; the only way to log into such a system is then via a serial
+	  or network connection.
+
+	  If unsure, say Y, or else you won't be able to do much with your new
+	  shiny Linux system :-)
+
+config CONSOLE_TRANSLATIONS
+	depends on VT
+	default y
+	bool "Enable character translations in console" if EXPERT
+	---help---
+	  This enables support for font mapping and Unicode translation
+	  on virtual consoles.
+
+config VT_CONSOLE
+	bool "Support for console on virtual terminal" if EXPERT
+	depends on VT
+	default y
+	---help---
+	  The system console is the device which receives all kernel messages
+	  and warnings and which allows logins in single user mode. If you
+	  answer Y here, a virtual terminal (the device used to interact with
+	  a physical terminal) can be used as system console. This is the most
+	  common mode of operations, so you should say Y here unless you want
+	  the kernel messages be output only to a serial port (in which case
+	  you should say Y to "Console on serial port", below).
+
+	  If you do say Y here, by default the currently visible virtual
+	  terminal (/dev/tty0) will be used as system console. You can change
+	  that with a kernel command line option such as "console=tty3" which
+	  would use the third virtual terminal as system console. (Try "man
+	  bootparam" or see the documentation of your boot loader (lilo or
+	  loadlin) about how to pass options to the kernel at boot time.)
+
+	  If unsure, say Y.
+
+config HW_CONSOLE
+	bool
+	depends on VT && !S390 && !UML
+	default y
+
+config VT_HW_CONSOLE_BINDING
+       bool "Support for binding and unbinding console drivers"
+       depends on HW_CONSOLE
+       default n
+       ---help---
+         The virtual terminal is the device that interacts with the physical
+         terminal through console drivers. On these systems, at least one
+         console driver is loaded. In other configurations, additional console
+         drivers may be enabled, such as the framebuffer console. If more than
+         1 console driver is enabled, setting this to 'y' will allow you to
+         select the console driver that will serve as the backend for the
+         virtual terminals.
+
+	 See <file:Documentation/console/console.txt> for more
+	 information. For framebuffer console users, please refer to
+	 <file:Documentation/fb/fbcon.txt>.
+
+config UNIX98_PTYS
+	bool "Unix98 PTY support" if EXPERT
+	default y
+	---help---
+	  A pseudo terminal (PTY) is a software device consisting of two
+	  halves: a master and a slave. The slave device behaves identical to
+	  a physical terminal; the master device is used by a process to
+	  read data from and write data to the slave, thereby emulating a
+	  terminal. Typical programs for the master side are telnet servers
+	  and xterms.
+
+	  Linux has traditionally used the BSD-like names /dev/ptyxx for
+	  masters and /dev/ttyxx for slaves of pseudo terminals. This scheme
+	  has a number of problems. The GNU C library glibc 2.1 and later,
+	  however, supports the Unix98 naming standard: in order to acquire a
+	  pseudo terminal, a process opens /dev/ptmx; the number of the pseudo
+	  terminal is then made available to the process and the pseudo
+	  terminal slave can be accessed as /dev/pts/<number>. What was
+	  traditionally /dev/ttyp2 will then be /dev/pts/2, for example.
+
+	  All modern Linux systems use the Unix98 ptys.  Say Y unless
+	  you're on an embedded system and want to conserve memory.
+
+config DEVPTS_MULTIPLE_INSTANCES
+	bool "Support multiple instances of devpts"
+	depends on UNIX98_PTYS
+	default n
+	---help---
+	  Enable support for multiple instances of devpts filesystem.
+	  If you want to have isolated PTY namespaces (eg: in containers),
+	  say Y here.  Otherwise, say N. If enabled, each mount of devpts
+	  filesystem with the '-o newinstance' option will create an
+	  independent PTY namespace.
+
+config LEGACY_PTYS
+	bool "Legacy (BSD) PTY support"
+	default y
+	---help---
+	  A pseudo terminal (PTY) is a software device consisting of two
+	  halves: a master and a slave. The slave device behaves identical to
+	  a physical terminal; the master device is used by a process to
+	  read data from and write data to the slave, thereby emulating a
+	  terminal. Typical programs for the master side are telnet servers
+	  and xterms.
+
+	  Linux has traditionally used the BSD-like names /dev/ptyxx
+	  for masters and /dev/ttyxx for slaves of pseudo
+	  terminals. This scheme has a number of problems, including
+	  security.  This option enables these legacy devices; on most
+	  systems, it is safe to say N.
+
+
+config LEGACY_PTY_COUNT
+	int "Maximum number of legacy PTY in use"
+	depends on LEGACY_PTYS
+	range 0 256
+	default "256"
+	---help---
+	  The maximum number of legacy PTYs that can be used at any one time.
+	  The default is 256, and should be more than enough.  Embedded
+	  systems may want to reduce this to save memory.
+
+	  When not in use, each legacy PTY occupies 12 bytes on 32-bit
+	  architectures and 24 bytes on 64-bit architectures.
+
+config BFIN_JTAG_COMM
+	tristate "Blackfin JTAG Communication"
+	depends on BLACKFIN
+	help
+	  Add support for emulating a TTY device over the Blackfin JTAG.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called bfin_jtag_comm.
+
+config BFIN_JTAG_COMM_CONSOLE
+	bool "Console on Blackfin JTAG"
+	depends on BFIN_JTAG_COMM=y
+
+config SERIAL_NONSTANDARD
+	bool "Non-standard serial port support"
+	depends on HAS_IOMEM
+	---help---
+	  Say Y here if you have any non-standard serial boards -- boards
+	  which aren't supported using the standard "dumb" serial driver.
+	  This includes intelligent serial boards such as Cyclades,
+	  Digiboards, etc. These are usually used for systems that need many
+	  serial ports because they serve many terminals or dial-in
+	  connections.
+
+	  Note that the answer to this question won't directly affect the
+	  kernel: saying N will just cause the configurator to skip all
+	  the questions about non-standard serial boards.
+
+	  Most people can say N here.
+
+config ROCKETPORT
+	tristate "Comtrol RocketPort support"
+	depends on SERIAL_NONSTANDARD && (ISA || EISA || PCI)
+	help
+	  This driver supports Comtrol RocketPort and RocketModem PCI boards.   
+          These boards provide 2, 4, 8, 16, or 32 high-speed serial ports or
+          modems.  For information about the RocketPort/RocketModem  boards
+          and this driver read <file:Documentation/serial/rocket.txt>.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called rocket.
+
+	  If you want to compile this driver into the kernel, say Y here.  If
+          you don't have a Comtrol RocketPort/RocketModem card installed, say N.
+
+config CYCLADES
+	tristate "Cyclades async mux support"
+	depends on SERIAL_NONSTANDARD && (PCI || ISA)
+	select FW_LOADER
+	---help---
+	  This driver supports Cyclades Z and Y multiserial boards.
+	  You would need something like this to connect more than two modems to
+	  your Linux box, for instance in order to become a dial-in server.
+
+	  For information about the Cyclades-Z card, read
+	  <file:Documentation/serial/README.cycladesZ>.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called cyclades.
+
+	  If you haven't heard about it, it's safe to say N.
+
+config CYZ_INTR
+	bool "Cyclades-Z interrupt mode operation (EXPERIMENTAL)"
+	depends on EXPERIMENTAL && CYCLADES
+	help
+	  The Cyclades-Z family of multiport cards allows 2 (two) driver op
+	  modes: polling and interrupt. In polling mode, the driver will check
+	  the status of the Cyclades-Z ports every certain amount of time
+	  (which is called polling cycle and is configurable). In interrupt
+	  mode, it will use an interrupt line (IRQ) in order to check the
+	  status of the Cyclades-Z ports. The default op mode is polling. If
+	  unsure, say N.
+
+config MOXA_INTELLIO
+	tristate "Moxa Intellio support"
+	depends on SERIAL_NONSTANDARD && (ISA || EISA || PCI)
+	select FW_LOADER
+	help
+	  Say Y here if you have a Moxa Intellio multiport serial card.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called moxa.
+
+config MOXA_SMARTIO
+	tristate "Moxa SmartIO support v. 2.0"
+	depends on SERIAL_NONSTANDARD && (PCI || EISA || ISA)
+	help
+	  Say Y here if you have a Moxa SmartIO multiport serial card and/or
+	  want to help develop a new version of this driver.
+
+	  This is upgraded (1.9.1) driver from original Moxa drivers with
+	  changes finally resulting in PCI probing.
+
+	  This driver can also be built as a module. The module will be called
+	  mxser. If you want to do that, say M here.
+
+config SYNCLINK
+	tristate "Microgate SyncLink card support"
+	depends on SERIAL_NONSTANDARD && PCI && ISA_DMA_API
+	help
+	  Provides support for the SyncLink ISA and PCI multiprotocol serial
+	  adapters. These adapters support asynchronous and HDLC bit
+	  synchronous communication up to 10Mbps (PCI adapter).
+
+	  This driver can only be built as a module ( = code which can be
+	  inserted in and removed from the running kernel whenever you want).
+	  The module will be called synclink.  If you want to do that, say M
+	  here.
+
+config SYNCLINKMP
+	tristate "SyncLink Multiport support"
+	depends on SERIAL_NONSTANDARD && PCI
+	help
+	  Enable support for the SyncLink Multiport (2 or 4 ports)
+	  serial adapter, running asynchronous and HDLC communications up
+	  to 2.048Mbps. Each ports is independently selectable for
+	  RS-232, V.35, RS-449, RS-530, and X.21
+
+	  This driver may be built as a module ( = code which can be
+	  inserted in and removed from the running kernel whenever you want).
+	  The module will be called synclinkmp.  If you want to do that, say M
+	  here.
+
+config SYNCLINK_GT
+	tristate "SyncLink GT/AC support"
+	depends on SERIAL_NONSTANDARD && PCI
+	help
+	  Support for SyncLink GT and SyncLink AC families of
+	  synchronous and asynchronous serial adapters
+	  manufactured by Microgate Systems, Ltd. (www.microgate.com)
+
+config NOZOMI
+	tristate "HSDPA Broadband Wireless Data Card - Globe Trotter"
+	depends on PCI && EXPERIMENTAL
+	help
+	  If you have a HSDPA driver Broadband Wireless Data Card -
+	  Globe Trotter PCMCIA card, say Y here.
+
+	  To compile this driver as a module, choose M here, the module
+	  will be called nozomi.
+
+config ISI
+	tristate "Multi-Tech multiport card support (EXPERIMENTAL)"
+	depends on SERIAL_NONSTANDARD && PCI
+	select FW_LOADER
+	help
+	  This is a driver for the Multi-Tech cards which provide several
+	  serial ports.  The driver is experimental and can currently only be
+	  built as a module. The module will be called isicom.
+	  If you want to do that, choose M here.
+
+config N_HDLC
+	tristate "HDLC line discipline support"
+	depends on SERIAL_NONSTANDARD
+	help
+	  Allows synchronous HDLC communications with tty device drivers that
+	  support synchronous HDLC such as the Microgate SyncLink adapter.
+
+	  This driver can be built as a module ( = code which can be
+	  inserted in and removed from the running kernel whenever you want).
+	  The module will be called n_hdlc. If you want to do that, say M
+	  here.
+
+config N_GSM
+	tristate "GSM MUX line discipline support (EXPERIMENTAL)"
+	depends on EXPERIMENTAL
+	depends on NET
+	help
+	  This line discipline provides support for the GSM MUX protocol and
+	  presents the mux as a set of 61 individual tty devices.
+

drivers/tty/Makefile

@@ -11,3 +11,18 @@ obj-$(CONFIG_R3964)		+= n_r3964.o
 obj-y				+= vt/
 obj-$(CONFIG_HVC_DRIVER)	+= hvc/
 obj-y				+= serial/
+
+# tty drivers
+obj-$(CONFIG_AMIGA_BUILTIN_SERIAL) += amiserial.o
+obj-$(CONFIG_BFIN_JTAG_COMM)	+= bfin_jtag_comm.o
+obj-$(CONFIG_CYCLADES)		+= cyclades.o
+obj-$(CONFIG_ISI)		+= isicom.o
+obj-$(CONFIG_MOXA_INTELLIO)	+= moxa.o
+obj-$(CONFIG_MOXA_SMARTIO)	+= mxser.o
+obj-$(CONFIG_NOZOMI)		+= nozomi.o
+obj-$(CONFIG_ROCKETPORT)	+= rocket.o
+obj-$(CONFIG_SYNCLINK_GT)	+= synclink_gt.o
+obj-$(CONFIG_SYNCLINKMP)	+= synclinkmp.o
+obj-$(CONFIG_SYNCLINK)		+= synclink.o
+
+obj-y += ipwireless/

drivers/tty/bfin_jtag_comm.c

@@ -0,0 +1,366 @@
+/*
+ * TTY over Blackfin JTAG Communication
+ *
+ * Copyright 2008-2009 Analog Devices Inc.
+ *
+ * Enter bugs at http://blackfin.uclinux.org/
+ *
+ * Licensed under the GPL-2 or later.
+ */
+
+#define DRV_NAME "bfin-jtag-comm"
+#define DEV_NAME "ttyBFJC"
+#define pr_fmt(fmt) DRV_NAME ": " fmt
+
+#include <linux/circ_buf.h>
+#include <linux/console.h>
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/kernel.h>
+#include <linux/kthread.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/sched.h>
+#include <linux/slab.h>
+#include <linux/tty.h>
+#include <linux/tty_driver.h>
+#include <linux/tty_flip.h>
+#include <asm/atomic.h>
+
+#define pr_init(fmt, args...) ({ static const __initconst char __fmt[] = fmt; printk(__fmt, ## args); })
+
+/* See the Debug/Emulation chapter in the HRM */
+#define EMUDOF   0x00000001	/* EMUDAT_OUT full & valid */
+#define EMUDIF   0x00000002	/* EMUDAT_IN full & valid */
+#define EMUDOOVF 0x00000004	/* EMUDAT_OUT overflow */
+#define EMUDIOVF 0x00000008	/* EMUDAT_IN overflow */
+
+static inline uint32_t bfin_write_emudat(uint32_t emudat)
+{
+	__asm__ __volatile__("emudat = %0;" : : "d"(emudat));
+	return emudat;
+}
+
+static inline uint32_t bfin_read_emudat(void)
+{
+	uint32_t emudat;
+	__asm__ __volatile__("%0 = emudat;" : "=d"(emudat));
+	return emudat;
+}
+
+static inline uint32_t bfin_write_emudat_chars(char a, char b, char c, char d)
+{
+	return bfin_write_emudat((a << 0) | (b << 8) | (c << 16) | (d << 24));
+}
+
+#define CIRC_SIZE 2048	/* see comment in tty_io.c:do_tty_write() */
+#define CIRC_MASK (CIRC_SIZE - 1)
+#define circ_empty(circ)     ((circ)->head == (circ)->tail)
+#define circ_free(circ)      CIRC_SPACE((circ)->head, (circ)->tail, CIRC_SIZE)
+#define circ_cnt(circ)       CIRC_CNT((circ)->head, (circ)->tail, CIRC_SIZE)
+#define circ_byte(circ, idx) ((circ)->buf[(idx) & CIRC_MASK])
+
+static struct tty_driver *bfin_jc_driver;
+static struct task_struct *bfin_jc_kthread;
+static struct tty_struct * volatile bfin_jc_tty;
+static unsigned long bfin_jc_count;
+static DEFINE_MUTEX(bfin_jc_tty_mutex);
+static volatile struct circ_buf bfin_jc_write_buf;
+
+static int
+bfin_jc_emudat_manager(void *arg)
+{
+	uint32_t inbound_len = 0, outbound_len = 0;
+
+	while (!kthread_should_stop()) {
+		/* no one left to give data to, so sleep */
+		if (bfin_jc_tty == NULL && circ_empty(&bfin_jc_write_buf)) {
+			pr_debug("waiting for readers\n");
+			__set_current_state(TASK_UNINTERRUPTIBLE);
+			schedule();
+			__set_current_state(TASK_RUNNING);
+		}
+
+		/* no data available, so just chill */
+		if (!(bfin_read_DBGSTAT() & EMUDIF) && circ_empty(&bfin_jc_write_buf)) {
+			pr_debug("waiting for data (in_len = %i) (circ: %i %i)\n",
+				inbound_len, bfin_jc_write_buf.tail, bfin_jc_write_buf.head);
+			if (inbound_len)
+				schedule();
+			else
+				schedule_timeout_interruptible(HZ);
+			continue;
+		}
+
+		/* if incoming data is ready, eat it */
+		if (bfin_read_DBGSTAT() & EMUDIF) {
+			struct tty_struct *tty;
+			mutex_lock(&bfin_jc_tty_mutex);
+			tty = (struct tty_struct *)bfin_jc_tty;
+			if (tty != NULL) {
+				uint32_t emudat = bfin_read_emudat();
+				if (inbound_len == 0) {
+					pr_debug("incoming length: 0x%08x\n", emudat);
+					inbound_len = emudat;
+				} else {
+					size_t num_chars = (4 <= inbound_len ? 4 : inbound_len);
+					pr_debug("  incoming data: 0x%08x (pushing %zu)\n", emudat, num_chars);
+					inbound_len -= num_chars;
+					tty_insert_flip_string(tty, (unsigned char *)&emudat, num_chars);
+					tty_flip_buffer_push(tty);
+				}
+			}
+			mutex_unlock(&bfin_jc_tty_mutex);
+		}
+
+		/* if outgoing data is ready, post it */
+		if (!(bfin_read_DBGSTAT() & EMUDOF) && !circ_empty(&bfin_jc_write_buf)) {
+			if (outbound_len == 0) {
+				outbound_len = circ_cnt(&bfin_jc_write_buf);
+				bfin_write_emudat(outbound_len);
+				pr_debug("outgoing length: 0x%08x\n", outbound_len);
+			} else {
+				struct tty_struct *tty;
+				int tail = bfin_jc_write_buf.tail;
+				size_t ate = (4 <= outbound_len ? 4 : outbound_len);
+				uint32_t emudat =
+				bfin_write_emudat_chars(
+					circ_byte(&bfin_jc_write_buf, tail + 0),
+					circ_byte(&bfin_jc_write_buf, tail + 1),
+					circ_byte(&bfin_jc_write_buf, tail + 2),
+					circ_byte(&bfin_jc_write_buf, tail + 3)
+				);
+				bfin_jc_write_buf.tail += ate;
+				outbound_len -= ate;
+				mutex_lock(&bfin_jc_tty_mutex);
+				tty = (struct tty_struct *)bfin_jc_tty;
+				if (tty)
+					tty_wakeup(tty);
+				mutex_unlock(&bfin_jc_tty_mutex);
+				pr_debug("  outgoing data: 0x%08x (pushing %zu)\n", emudat, ate);
+			}
+		}
+	}
+
+	__set_current_state(TASK_RUNNING);
+	return 0;
+}
+
+static int
+bfin_jc_open(struct tty_struct *tty, struct file *filp)
+{
+	mutex_lock(&bfin_jc_tty_mutex);
+	pr_debug("open %lu\n", bfin_jc_count);
+	++bfin_jc_count;
+	bfin_jc_tty = tty;
+	wake_up_process(bfin_jc_kthread);
+	mutex_unlock(&bfin_jc_tty_mutex);
+	return 0;
+}
+
+static void
+bfin_jc_close(struct tty_struct *tty, struct file *filp)
+{
+	mutex_lock(&bfin_jc_tty_mutex);
+	pr_debug("close %lu\n", bfin_jc_count);
+	if (--bfin_jc_count == 0)
+		bfin_jc_tty = NULL;
+	wake_up_process(bfin_jc_kthread);
+	mutex_unlock(&bfin_jc_tty_mutex);
+}
+
+/* XXX: we dont handle the put_char() case where we must handle count = 1 */
+static int
+bfin_jc_circ_write(const unsigned char *buf, int count)
+{
+	int i;
+	count = min(count, circ_free(&bfin_jc_write_buf));
+	pr_debug("going to write chunk of %i bytes\n", count);
+	for (i = 0; i < count; ++i)
+		circ_byte(&bfin_jc_write_buf, bfin_jc_write_buf.head + i) = buf[i];
+	bfin_jc_write_buf.head += i;
+	return i;
+}
+
+#ifndef CONFIG_BFIN_JTAG_COMM_CONSOLE
+# define console_lock()
+# define console_unlock()
+#endif
+static int
+bfin_jc_write(struct tty_struct *tty, const unsigned char *buf, int count)
+{
+	int i;
+	console_lock();
+	i = bfin_jc_circ_write(buf, count);
+	console_unlock();
+	wake_up_process(bfin_jc_kthread);
+	return i;
+}
+
+static void
+bfin_jc_flush_chars(struct tty_struct *tty)
+{
+	wake_up_process(bfin_jc_kthread);
+}
+
+static int
+bfin_jc_write_room(struct tty_struct *tty)
+{
+	return circ_free(&bfin_jc_write_buf);
+}
+
+static int
+bfin_jc_chars_in_buffer(struct tty_struct *tty)
+{
+	return circ_cnt(&bfin_jc_write_buf);
+}
+
+static void
+bfin_jc_wait_until_sent(struct tty_struct *tty, int timeout)
+{
+	unsigned long expire = jiffies + timeout;
+	while (!circ_empty(&bfin_jc_write_buf)) {
+		if (signal_pending(current))
+			break;
+		if (time_after(jiffies, expire))
+			break;
+	}
+}
+
+static const struct tty_operations bfin_jc_ops = {
+	.open            = bfin_jc_open,
+	.close           = bfin_jc_close,
+	.write           = bfin_jc_write,
+	/*.put_char        = bfin_jc_put_char,*/
+	.flush_chars     = bfin_jc_flush_chars,
+	.write_room      = bfin_jc_write_room,
+	.chars_in_buffer = bfin_jc_chars_in_buffer,
+	.wait_until_sent = bfin_jc_wait_until_sent,
+};
+
+static int __init bfin_jc_init(void)
+{
+	int ret;
+
+	bfin_jc_kthread = kthread_create(bfin_jc_emudat_manager, NULL, DRV_NAME);
+	if (IS_ERR(bfin_jc_kthread))
+		return PTR_ERR(bfin_jc_kthread);
+
+	ret = -ENOMEM;
+
+	bfin_jc_write_buf.head = bfin_jc_write_buf.tail = 0;
+	bfin_jc_write_buf.buf = kmalloc(CIRC_SIZE, GFP_KERNEL);
+	if (!bfin_jc_write_buf.buf)
+		goto err;
+
+	bfin_jc_driver = alloc_tty_driver(1);
+	if (!bfin_jc_driver)
+		goto err;
+
+	bfin_jc_driver->owner        = THIS_MODULE;
+	bfin_jc_driver->driver_name  = DRV_NAME;
+	bfin_jc_driver->name         = DEV_NAME;
+	bfin_jc_driver->type         = TTY_DRIVER_TYPE_SERIAL;
+	bfin_jc_driver->subtype      = SERIAL_TYPE_NORMAL;
+	bfin_jc_driver->init_termios = tty_std_termios;
+	tty_set_operations(bfin_jc_driver, &bfin_jc_ops);
+
+	ret = tty_register_driver(bfin_jc_driver);
+	if (ret)
+		goto err;
+
+	pr_init(KERN_INFO DRV_NAME ": initialized\n");
+
+	return 0;
+
+ err:
+	put_tty_driver(bfin_jc_driver);
+	kfree(bfin_jc_write_buf.buf);
+	kthread_stop(bfin_jc_kthread);
+	return ret;
+}
+module_init(bfin_jc_init);
+
+static void __exit bfin_jc_exit(void)
+{
+	kthread_stop(bfin_jc_kthread);
+	kfree(bfin_jc_write_buf.buf);
+	tty_unregister_driver(bfin_jc_driver);
+	put_tty_driver(bfin_jc_driver);
+}
+module_exit(bfin_jc_exit);
+
+#if defined(CONFIG_BFIN_JTAG_COMM_CONSOLE) || defined(CONFIG_EARLY_PRINTK)
+static void
+bfin_jc_straight_buffer_write(const char *buf, unsigned count)
+{
+	unsigned ate = 0;
+	while (bfin_read_DBGSTAT() & EMUDOF)
+		continue;
+	bfin_write_emudat(count);
+	while (ate < count) {
+		while (bfin_read_DBGSTAT() & EMUDOF)
+			continue;
+		bfin_write_emudat_chars(buf[ate], buf[ate+1], buf[ate+2], buf[ate+3]);
+		ate += 4;
+	}
+}
+#endif
+
+#ifdef CONFIG_BFIN_JTAG_COMM_CONSOLE
+static void
+bfin_jc_console_write(struct console *co, const char *buf, unsigned count)
+{
+	if (bfin_jc_kthread == NULL)
+		bfin_jc_straight_buffer_write(buf, count);
+	else
+		bfin_jc_circ_write(buf, count);
+}
+
+static struct tty_driver *
+bfin_jc_console_device(struct console *co, int *index)
+{
+	*index = co->index;
+	return bfin_jc_driver;
+}
+
+static struct console bfin_jc_console = {
+	.name    = DEV_NAME,
+	.write   = bfin_jc_console_write,
+	.device  = bfin_jc_console_device,
+	.flags   = CON_ANYTIME | CON_PRINTBUFFER,
+	.index   = -1,
+};
+
+static int __init bfin_jc_console_init(void)
+{
+	register_console(&bfin_jc_console);
+	return 0;
+}
+console_initcall(bfin_jc_console_init);
+#endif
+
+#ifdef CONFIG_EARLY_PRINTK
+static void __init
+bfin_jc_early_write(struct console *co, const char *buf, unsigned int count)
+{
+	bfin_jc_straight_buffer_write(buf, count);
+}
+
+static struct __initdata console bfin_jc_early_console = {
+	.name   = "early_BFJC",
+	.write   = bfin_jc_early_write,
+	.flags   = CON_ANYTIME | CON_PRINTBUFFER,
+	.index   = -1,
+};
+
+struct console * __init
+bfin_jc_early_init(unsigned int port, unsigned int cflag)
+{
+	return &bfin_jc_early_console;
+}
+#endif
+
+MODULE_AUTHOR("Mike Frysinger <[email protected]>");
+MODULE_DESCRIPTION("TTY over Blackfin JTAG Communication");
+MODULE_LICENSE("GPL");

drivers/tty/hvc/Kconfig

@@ -0,0 +1,105 @@
+config HVC_DRIVER
+	bool
+	help
+	  Generic "hypervisor virtual console" infrastructure for various
+	  hypervisors (pSeries, iSeries, Xen, lguest).
+	  It will automatically be selected if one of the back-end console drivers
+	  is selected.
+
+config HVC_IRQ
+	bool
+
+config HVC_CONSOLE
+	bool "pSeries Hypervisor Virtual Console support"
+	depends on PPC_PSERIES
+	select HVC_DRIVER
+	select HVC_IRQ
+	help
+	  pSeries machines when partitioned support a hypervisor virtual
+	  console. This driver allows each pSeries partition to have a console
+	  which is accessed via the HMC.
+
+config HVC_ISERIES
+	bool "iSeries Hypervisor Virtual Console support"
+	depends on PPC_ISERIES
+	default y
+	select HVC_DRIVER
+	select HVC_IRQ
+	select VIOPATH
+	help
+	  iSeries machines support a hypervisor virtual console.
+
+config HVC_RTAS
+	bool "IBM RTAS Console support"
+	depends on PPC_RTAS
+	select HVC_DRIVER
+	help
+	  IBM Console device driver which makes use of RTAS
+
+config HVC_BEAT
+	bool "Toshiba's Beat Hypervisor Console support"
+	depends on PPC_CELLEB
+	select HVC_DRIVER
+	help
+	  Toshiba's Cell Reference Set Beat Console device driver
+
+config HVC_IUCV
+	bool "z/VM IUCV Hypervisor console support (VM only)"
+	depends on S390
+	select HVC_DRIVER
+	select IUCV
+	default y
+	help
+	  This driver provides a Hypervisor console (HVC) back-end to access
+	  a Linux (console) terminal via a z/VM IUCV communication path.
+
+config HVC_XEN
+	bool "Xen Hypervisor Console support"
+	depends on XEN
+	select HVC_DRIVER
+	select HVC_IRQ
+	default y
+	help
+	  Xen virtual console device driver
+
+config HVC_UDBG
+       bool "udbg based fake hypervisor console"
+       depends on PPC && EXPERIMENTAL
+       select HVC_DRIVER
+       default n
+
+config HVC_DCC
+       bool "ARM JTAG DCC console"
+       depends on ARM
+       select HVC_DRIVER
+       help
+         This console uses the JTAG DCC on ARM to create a console under the HVC
+	 driver. This console is used through a JTAG only on ARM. If you don't have
+	 a JTAG then you probably don't want this option.
+
+config HVC_BFIN_JTAG
+	bool "Blackfin JTAG console"
+	depends on BLACKFIN
+	select HVC_DRIVER
+	help
+	 This console uses the Blackfin JTAG to create a console under the
+	 the HVC driver.  If you don't have JTAG, then you probably don't
+	 want this option.
+
+config HVCS
+	tristate "IBM Hypervisor Virtual Console Server support"
+	depends on PPC_PSERIES && HVC_CONSOLE
+	help
+	  Partitionable IBM Power5 ppc64 machines allow hosting of
+	  firmware virtual consoles from one Linux partition by
+	  another Linux partition.  This driver allows console data
+	  from Linux partitions to be accessed through TTY device
+	  interfaces in the device tree of a Linux partition running
+	  this driver.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called hvcs.  Additionally, this module
+	  will depend on arch specific APIs exported from hvcserver.ko
+	  which will also be compiled when this driver is built as a
+	  module.
+

drivers/tty/hvc/Makefile

@@ -9,4 +9,5 @@ obj-$(CONFIG_HVC_IRQ)		+= hvc_irq.o
 obj-$(CONFIG_HVC_XEN)		+= hvc_xen.o
 obj-$(CONFIG_HVC_IUCV)		+= hvc_iucv.o
 obj-$(CONFIG_HVC_UDBG)		+= hvc_udbg.o
+obj-$(CONFIG_HVC_BFIN_JTAG)	+= hvc_bfin_jtag.o
 obj-$(CONFIG_HVCS)		+= hvcs.o

drivers/tty/hvc/hvc_bfin_jtag.c

@@ -0,0 +1,105 @@
+/*
+ * Console via Blackfin JTAG Communication
+ *
+ * Copyright 2008-2011 Analog Devices Inc.
+ *
+ * Enter bugs at http://blackfin.uclinux.org/
+ *
+ * Licensed under the GPL-2 or later.
+ */
+
+#include <linux/console.h>
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/init.h>
+#include <linux/moduleparam.h>
+#include <linux/types.h>
+
+#include "hvc_console.h"
+
+/* See the Debug/Emulation chapter in the HRM */
+#define EMUDOF   0x00000001	/* EMUDAT_OUT full & valid */
+#define EMUDIF   0x00000002	/* EMUDAT_IN full & valid */
+#define EMUDOOVF 0x00000004	/* EMUDAT_OUT overflow */
+#define EMUDIOVF 0x00000008	/* EMUDAT_IN overflow */
+
+/* Helper functions to glue the register API to simple C operations */
+static inline uint32_t bfin_write_emudat(uint32_t emudat)
+{
+	__asm__ __volatile__("emudat = %0;" : : "d"(emudat));
+	return emudat;
+}
+
+static inline uint32_t bfin_read_emudat(void)
+{
+	uint32_t emudat;
+	__asm__ __volatile__("%0 = emudat;" : "=d"(emudat));
+	return emudat;
+}
+
+/* Send data to the host */
+static int hvc_bfin_put_chars(uint32_t vt, const char *buf, int count)
+{
+	static uint32_t outbound_len;
+	uint32_t emudat;
+	int ret;
+
+	if (bfin_read_DBGSTAT() & EMUDOF)
+		return 0;
+
+	if (!outbound_len) {
+		outbound_len = count;
+		bfin_write_emudat(outbound_len);
+		return 0;
+	}
+
+	ret = min(outbound_len, (uint32_t)4);
+	memcpy(&emudat, buf, ret);
+	bfin_write_emudat(emudat);
+	outbound_len -= ret;
+
+	return ret;
+}
+
+/* Receive data from the host */
+static int hvc_bfin_get_chars(uint32_t vt, char *buf, int count)
+{
+	static uint32_t inbound_len;
+	uint32_t emudat;
+	int ret;
+
+	if (!(bfin_read_DBGSTAT() & EMUDIF))
+		return 0;
+	emudat = bfin_read_emudat();
+
+	if (!inbound_len) {
+		inbound_len = emudat;
+		return 0;
+	}
+
+	ret = min(inbound_len, (uint32_t)4);
+	memcpy(buf, &emudat, ret);
+	inbound_len -= ret;
+
+	return ret;
+}
+
+/* Glue the HVC layers to the Blackfin layers */
+static const struct hv_ops hvc_bfin_get_put_ops = {
+	.get_chars = hvc_bfin_get_chars,
+	.put_chars = hvc_bfin_put_chars,
+};
+
+static int __init hvc_bfin_console_init(void)
+{
+	hvc_instantiate(0, 0, &hvc_bfin_get_put_ops);
+	return 0;
+}
+console_initcall(hvc_bfin_console_init);
+
+static int __init hvc_bfin_init(void)
+{
+	hvc_alloc(0, 0, &hvc_bfin_get_put_ops, 128);
+	return 0;
+}
+device_initcall(hvc_bfin_init);

drivers/tty/hvc/hvc_dcc.c

@@ -33,54 +33,29 @@
 static inline u32 __dcc_getstatus(void)
 {
 	u32 __ret;
-
-	asm("mrc p14, 0, %0, c0, c1, 0	@ read comms ctrl reg"
+	asm volatile("mrc p14, 0, %0, c0, c1, 0	@ read comms ctrl reg"
 		: "=r" (__ret) : : "cc");
 
 	return __ret;
 }
 
 
-#if defined(CONFIG_CPU_V7)
 static inline char __dcc_getchar(void)
 {
 	char __c;
 
-	asm("get_wait:	mrc p14, 0, pc, c0, c1, 0                          \n\
-			bne get_wait                                       \n\
-			mrc p14, 0, %0, c0, c5, 0	@ read comms data reg"
-		: "=r" (__c) : : "cc");
-
-	return __c;
-}
-#else
-static inline char __dcc_getchar(void)
-{
-	char __c;
-
-	asm("mrc p14, 0, %0, c0, c5, 0	@ read comms data reg"
+	asm volatile("mrc p14, 0, %0, c0, c5, 0	@ read comms data reg"
 		: "=r" (__c));
 
 	return __c;
 }
-#endif
 
-#if defined(CONFIG_CPU_V7)
 static inline void __dcc_putchar(char c)
 {
-	asm("put_wait:	mrc p14, 0, pc, c0, c1, 0                 \n\
-			bcs put_wait                              \n\
-			mcr p14, 0, %0, c0, c5, 0                   "
-	: : "r" (c) : "cc");
-}
-#else
-static inline void __dcc_putchar(char c)
-{
-	asm("mcr p14, 0, %0, c0, c5, 0	@ write a char"
+	asm volatile("mcr p14, 0, %0, c0, c5, 0	@ write a char"
 		: /* no output register */
 		: "r" (c));
 }
-#endif
 
 static int hvc_dcc_put_chars(uint32_t vt, const char *buf, int count)
 {
@@ -90,7 +65,7 @@ static int hvc_dcc_put_chars(uint32_t vt, const char *buf, int count)
 		while (__dcc_getstatus() & DCC_STATUS_TX)
 			cpu_relax();
 
-		__dcc_putchar((char)(buf[i] & 0xFF));
+		__dcc_putchar(buf[i]);
 	}
 
 	return count;
@@ -100,15 +75,11 @@ static int hvc_dcc_get_chars(uint32_t vt, char *buf, int count)
 {
 	int i;
 
-	for (i = 0; i < count; ++i) {
-		int c = -1;
-
+	for (i = 0; i < count; ++i)
 		if (__dcc_getstatus() & DCC_STATUS_RX)
-			c = __dcc_getchar();
-		if (c < 0)
+			buf[i] = __dcc_getchar();
+		else
 			break;
-		buf[i] = c;
-	}
 
 	return i;
 }

drivers/tty/hvc/hvsi.c

@@ -1095,7 +1095,7 @@ static void hvsi_unthrottle(struct tty_struct *tty)
 	h_vio_signal(hp->vtermno, VIO_IRQ_ENABLE);
 }
 
-static int hvsi_tiocmget(struct tty_struct *tty, struct file *file)
+static int hvsi_tiocmget(struct tty_struct *tty)
 {
 	struct hvsi_struct *hp = tty->driver_data;
 
@@ -1103,8 +1103,8 @@ static int hvsi_tiocmget(struct tty_struct *tty, struct file *file)
 	return hp->mctrl;
 }
 
-static int hvsi_tiocmset(struct tty_struct *tty, struct file *file,
-		unsigned int set, unsigned int clear)
+static int hvsi_tiocmset(struct tty_struct *tty,
+				unsigned int set, unsigned int clear)
 {
 	struct hvsi_struct *hp = tty->driver_data;
 	unsigned long flags;

drivers/tty/ipwireless/Makefile

@@ -0,0 +1,10 @@
+#
+# drivers/char/pcmcia/ipwireless/Makefile
+#
+# Makefile for the IPWireless driver
+#
+
+obj-$(CONFIG_IPWIRELESS) += ipwireless.o
+
+ipwireless-y := hardware.o main.o network.o tty.o
+

drivers/tty/ipwireless/hardware.h

@@ -0,0 +1,62 @@
+/*
+ * IPWireless 3G PCMCIA Network Driver
+ *
+ * Original code
+ *   by Stephen Blackheath <stephen@blacksapphire.com>,
+ *      Ben Martel <benm@symmetric.co.nz>
+ *
+ * Copyrighted as follows:
+ *   Copyright (C) 2004 by Symmetric Systems Ltd (NZ)
+ *
+ * Various driver changes and rewrites, port to new kernels
+ *   Copyright (C) 2006-2007 Jiri Kosina
+ *
+ * Misc code cleanups and updates
+ *   Copyright (C) 2007 David Sterba
+ */
+
+#ifndef _IPWIRELESS_CS_HARDWARE_H_
+#define _IPWIRELESS_CS_HARDWARE_H_
+
+#include <linux/types.h>
+#include <linux/sched.h>
+#include <linux/interrupt.h>
+
+#define IPW_CONTROL_LINE_CTS 0x0001
+#define IPW_CONTROL_LINE_DCD 0x0002
+#define IPW_CONTROL_LINE_DSR 0x0004
+#define IPW_CONTROL_LINE_RI  0x0008
+#define IPW_CONTROL_LINE_DTR 0x0010
+#define IPW_CONTROL_LINE_RTS 0x0020
+
+struct ipw_hardware;
+struct ipw_network;
+
+struct ipw_hardware *ipwireless_hardware_create(void);
+void ipwireless_hardware_free(struct ipw_hardware *hw);
+irqreturn_t ipwireless_interrupt(int irq, void *dev_id);
+int ipwireless_set_DTR(struct ipw_hardware *hw, unsigned int channel_idx,
+		int state);
+int ipwireless_set_RTS(struct ipw_hardware *hw, unsigned int channel_idx,
+		int state);
+int ipwireless_send_packet(struct ipw_hardware *hw,
+			    unsigned int channel_idx,
+			    const unsigned char *data,
+			    unsigned int length,
+			    void (*packet_sent_callback) (void *cb,
+							  unsigned int length),
+			    void *sent_cb_data);
+void ipwireless_associate_network(struct ipw_hardware *hw,
+		struct ipw_network *net);
+void ipwireless_stop_interrupts(struct ipw_hardware *hw);
+void ipwireless_init_hardware_v1(struct ipw_hardware *hw,
+				 unsigned int base_port,
+				 void __iomem *attr_memory,
+				 void __iomem *common_memory,
+				 int is_v2_card,
+				 void (*reboot_cb) (void *data),
+				 void *reboot_cb_data);
+void ipwireless_init_hardware_v2_v3(struct ipw_hardware *hw);
+void ipwireless_sleep(unsigned int tenths);
+
+#endif

drivers/tty/ipwireless/main.c

@@ -0,0 +1,347 @@
+/*
+ * IPWireless 3G PCMCIA Network Driver
+ *
+ * Original code
+ *   by Stephen Blackheath <stephen@blacksapphire.com>,
+ *      Ben Martel <benm@symmetric.co.nz>
+ *
+ * Copyrighted as follows:
+ *   Copyright (C) 2004 by Symmetric Systems Ltd (NZ)
+ *
+ * Various driver changes and rewrites, port to new kernels
+ *   Copyright (C) 2006-2007 Jiri Kosina
+ *
+ * Misc code cleanups and updates
+ *   Copyright (C) 2007 David Sterba
+ */
+
+#include "hardware.h"
+#include "network.h"
+#include "main.h"
+#include "tty.h"
+
+#include <linux/delay.h>
+#include <linux/init.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/sched.h>
+#include <linux/slab.h>
+
+#include <pcmcia/cisreg.h>
+#include <pcmcia/device_id.h>
+#include <pcmcia/ss.h>
+#include <pcmcia/ds.h>
+
+static struct pcmcia_device_id ipw_ids[] = {
+	PCMCIA_DEVICE_MANF_CARD(0x02f2, 0x0100),
+	PCMCIA_DEVICE_MANF_CARD(0x02f2, 0x0200),
+	PCMCIA_DEVICE_NULL
+};
+MODULE_DEVICE_TABLE(pcmcia, ipw_ids);
+
+static void ipwireless_detach(struct pcmcia_device *link);
+
+/*
+ * Module params
+ */
+/* Debug mode: more verbose, print sent/recv bytes */
+int ipwireless_debug;
+int ipwireless_loopback;
+int ipwireless_out_queue = 10;
+
+module_param_named(debug, ipwireless_debug, int, 0);
+module_param_named(loopback, ipwireless_loopback, int, 0);
+module_param_named(out_queue, ipwireless_out_queue, int, 0);
+MODULE_PARM_DESC(debug, "switch on debug messages [0]");
+MODULE_PARM_DESC(loopback,
+		"debug: enable ras_raw channel [0]");
+MODULE_PARM_DESC(out_queue, "debug: set size of outgoing PPP queue [10]");
+
+/* Executes in process context. */
+static void signalled_reboot_work(struct work_struct *work_reboot)
+{
+	struct ipw_dev *ipw = container_of(work_reboot, struct ipw_dev,
+			work_reboot);
+	struct pcmcia_device *link = ipw->link;
+	pcmcia_reset_card(link->socket);
+}
+
+static void signalled_reboot_callback(void *callback_data)
+{
+	struct ipw_dev *ipw = (struct ipw_dev *) callback_data;
+
+	/* Delegate to process context. */
+	schedule_work(&ipw->work_reboot);
+}
+
+static int ipwireless_probe(struct pcmcia_device *p_dev, void *priv_data)
+{
+	struct ipw_dev *ipw = priv_data;
+	int ret;
+
+	p_dev->resource[0]->flags &= ~IO_DATA_PATH_WIDTH;
+	p_dev->resource[0]->flags |= IO_DATA_PATH_WIDTH_AUTO;
+
+	/* 0x40 causes it to generate level mode interrupts. */
+	/* 0x04 enables IREQ pin. */
+	p_dev->config_index |= 0x44;
+	p_dev->io_lines = 16;
+	ret = pcmcia_request_io(p_dev);
+	if (ret)
+		return ret;
+
+	if (!request_region(p_dev->resource[0]->start,
+			    resource_size(p_dev->resource[0]),
+			    IPWIRELESS_PCCARD_NAME)) {
+		ret = -EBUSY;
+		goto exit;
+	}
+
+	p_dev->resource[2]->flags |=
+		WIN_DATA_WIDTH_16 | WIN_MEMORY_TYPE_CM | WIN_ENABLE;
+
+	ret = pcmcia_request_window(p_dev, p_dev->resource[2], 0);
+	if (ret != 0)
+		goto exit1;
+
+	ret = pcmcia_map_mem_page(p_dev, p_dev->resource[2], p_dev->card_addr);
+	if (ret != 0)
+		goto exit1;
+
+	ipw->is_v2_card = resource_size(p_dev->resource[2]) == 0x100;
+
+	ipw->common_memory = ioremap(p_dev->resource[2]->start,
+				resource_size(p_dev->resource[2]));
+	if (!request_mem_region(p_dev->resource[2]->start,
+				resource_size(p_dev->resource[2]),
+				IPWIRELESS_PCCARD_NAME)) {
+		ret = -EBUSY;
+		goto exit2;
+	}
+
+	p_dev->resource[3]->flags |= WIN_DATA_WIDTH_16 | WIN_MEMORY_TYPE_AM |
+					WIN_ENABLE;
+	p_dev->resource[3]->end = 0; /* this used to be 0x1000 */
+	ret = pcmcia_request_window(p_dev, p_dev->resource[3], 0);
+	if (ret != 0)
+		goto exit3;
+
+	ret = pcmcia_map_mem_page(p_dev, p_dev->resource[3], 0);
+	if (ret != 0)
+		goto exit3;
+
+	ipw->attr_memory = ioremap(p_dev->resource[3]->start,
+				resource_size(p_dev->resource[3]));
+	if (!request_mem_region(p_dev->resource[3]->start,
+				resource_size(p_dev->resource[3]),
+				IPWIRELESS_PCCARD_NAME)) {
+		ret = -EBUSY;
+		goto exit4;
+	}
+
+	return 0;
+
+exit4:
+	iounmap(ipw->attr_memory);
+exit3:
+	release_mem_region(p_dev->resource[2]->start,
+			resource_size(p_dev->resource[2]));
+exit2:
+	iounmap(ipw->common_memory);
+exit1:
+	release_region(p_dev->resource[0]->start,
+		       resource_size(p_dev->resource[0]));
+exit:
+	pcmcia_disable_device(p_dev);
+	return ret;
+}
+
+static int config_ipwireless(struct ipw_dev *ipw)
+{
+	struct pcmcia_device *link = ipw->link;
+	int ret = 0;
+
+	ipw->is_v2_card = 0;
+	link->config_flags |= CONF_AUTO_SET_IO | CONF_AUTO_SET_IOMEM |
+		CONF_ENABLE_IRQ;
+
+	ret = pcmcia_loop_config(link, ipwireless_probe, ipw);
+	if (ret != 0)
+		return ret;
+
+	INIT_WORK(&ipw->work_reboot, signalled_reboot_work);
+
+	ipwireless_init_hardware_v1(ipw->hardware, link->resource[0]->start,
+				    ipw->attr_memory, ipw->common_memory,
+				    ipw->is_v2_card, signalled_reboot_callback,
+				    ipw);
+
+	ret = pcmcia_request_irq(link, ipwireless_interrupt);
+	if (ret != 0)
+		goto exit;
+
+	printk(KERN_INFO IPWIRELESS_PCCARD_NAME ": Card type %s\n",
+			ipw->is_v2_card ? "V2/V3" : "V1");
+	printk(KERN_INFO IPWIRELESS_PCCARD_NAME
+		": I/O ports %pR, irq %d\n", link->resource[0],
+			(unsigned int) link->irq);
+	if (ipw->attr_memory && ipw->common_memory)
+		printk(KERN_INFO IPWIRELESS_PCCARD_NAME
+			": attr memory %pR, common memory %pR\n",
+			link->resource[3],
+			link->resource[2]);
+
+	ipw->network = ipwireless_network_create(ipw->hardware);
+	if (!ipw->network)
+		goto exit;
+
+	ipw->tty = ipwireless_tty_create(ipw->hardware, ipw->network);
+	if (!ipw->tty)
+		goto exit;
+
+	ipwireless_init_hardware_v2_v3(ipw->hardware);
+
+	/*
+	 * Do the RequestConfiguration last, because it enables interrupts.
+	 * Then we don't get any interrupts before we're ready for them.
+	 */
+	ret = pcmcia_enable_device(link);
+	if (ret != 0)
+		goto exit;
+
+	return 0;
+
+exit:
+	if (ipw->common_memory) {
+		release_mem_region(link->resource[2]->start,
+				resource_size(link->resource[2]));
+		iounmap(ipw->common_memory);
+	}
+	if (ipw->attr_memory) {
+		release_mem_region(link->resource[3]->start,
+				resource_size(link->resource[3]));
+		iounmap(ipw->attr_memory);
+	}
+	pcmcia_disable_device(link);
+	return -1;
+}
+
+static void release_ipwireless(struct ipw_dev *ipw)
+{
+	release_region(ipw->link->resource[0]->start,
+		       resource_size(ipw->link->resource[0]));
+	if (ipw->common_memory) {
+		release_mem_region(ipw->link->resource[2]->start,
+				resource_size(ipw->link->resource[2]));
+		iounmap(ipw->common_memory);
+	}
+	if (ipw->attr_memory) {
+		release_mem_region(ipw->link->resource[3]->start,
+				resource_size(ipw->link->resource[3]));
+		iounmap(ipw->attr_memory);
+	}
+	pcmcia_disable_device(ipw->link);
+}
+
+/*
+ * ipwireless_attach() creates an "instance" of the driver, allocating
+ * local data structures for one device (one interface).  The device
+ * is registered with Card Services.
+ *
+ * The pcmcia_device structure is initialized, but we don't actually
+ * configure the card at this point -- we wait until we receive a
+ * card insertion event.
+ */
+static int ipwireless_attach(struct pcmcia_device *link)
+{
+	struct ipw_dev *ipw;
+	int ret;
+
+	ipw = kzalloc(sizeof(struct ipw_dev), GFP_KERNEL);
+	if (!ipw)
+		return -ENOMEM;
+
+	ipw->link = link;
+	link->priv = ipw;
+
+	ipw->hardware = ipwireless_hardware_create();
+	if (!ipw->hardware) {
+		kfree(ipw);
+		return -ENOMEM;
+	}
+	/* RegisterClient will call config_ipwireless */
+
+	ret = config_ipwireless(ipw);
+
+	if (ret != 0) {
+		ipwireless_detach(link);
+		return ret;
+	}
+
+	return 0;
+}
+
+/*
+ * This deletes a driver "instance".  The device is de-registered with
+ * Card Services.  If it has been released, all local data structures
+ * are freed.  Otherwise, the structures will be freed when the device
+ * is released.
+ */
+static void ipwireless_detach(struct pcmcia_device *link)
+{
+	struct ipw_dev *ipw = link->priv;
+
+	release_ipwireless(ipw);
+
+	if (ipw->tty != NULL)
+		ipwireless_tty_free(ipw->tty);
+	if (ipw->network != NULL)
+		ipwireless_network_free(ipw->network);
+	if (ipw->hardware != NULL)
+		ipwireless_hardware_free(ipw->hardware);
+	kfree(ipw);
+}
+
+static struct pcmcia_driver me = {
+	.owner		= THIS_MODULE,
+	.probe          = ipwireless_attach,
+	.remove         = ipwireless_detach,
+	.name		= IPWIRELESS_PCCARD_NAME,
+	.id_table       = ipw_ids
+};
+
+/*
+ * Module insertion : initialisation of the module.
+ * Register the card with cardmgr...
+ */
+static int __init init_ipwireless(void)
+{
+	int ret;
+
+	ret = ipwireless_tty_init();
+	if (ret != 0)
+		return ret;
+
+	ret = pcmcia_register_driver(&me);
+	if (ret != 0)
+		ipwireless_tty_release();
+
+	return ret;
+}
+
+/*
+ * Module removal
+ */
+static void __exit exit_ipwireless(void)
+{
+	pcmcia_unregister_driver(&me);
+	ipwireless_tty_release();
+}
+
+module_init(init_ipwireless);
+module_exit(exit_ipwireless);
+
+MODULE_AUTHOR(IPWIRELESS_PCMCIA_AUTHOR);
+MODULE_DESCRIPTION(IPWIRELESS_PCCARD_NAME " " IPWIRELESS_PCMCIA_VERSION);
+MODULE_LICENSE("GPL");

drivers/tty/ipwireless/main.h

@@ -0,0 +1,68 @@
+/*
+ * IPWireless 3G PCMCIA Network Driver
+ *
+ * Original code
+ *   by Stephen Blackheath <stephen@blacksapphire.com>,
+ *      Ben Martel <benm@symmetric.co.nz>
+ *
+ * Copyrighted as follows:
+ *   Copyright (C) 2004 by Symmetric Systems Ltd (NZ)
+ *
+ * Various driver changes and rewrites, port to new kernels
+ *   Copyright (C) 2006-2007 Jiri Kosina
+ *
+ * Misc code cleanups and updates
+ *   Copyright (C) 2007 David Sterba
+ */
+
+#ifndef _IPWIRELESS_CS_H_
+#define _IPWIRELESS_CS_H_
+
+#include <linux/sched.h>
+#include <linux/types.h>
+
+#include <pcmcia/cistpl.h>
+#include <pcmcia/ds.h>
+
+#include "hardware.h"
+
+#define IPWIRELESS_PCCARD_NAME		"ipwireless"
+#define IPWIRELESS_PCMCIA_VERSION	"1.1"
+#define IPWIRELESS_PCMCIA_AUTHOR        \
+	"Stephen Blackheath, Ben Martel, Jiri Kosina and David Sterba"
+
+#define IPWIRELESS_TX_QUEUE_SIZE  262144
+#define IPWIRELESS_RX_QUEUE_SIZE  262144
+
+#define IPWIRELESS_STATE_DEBUG
+
+struct ipw_hardware;
+struct ipw_network;
+struct ipw_tty;
+
+struct ipw_dev {
+	struct pcmcia_device *link;
+	int is_v2_card;
+
+	void __iomem *attr_memory;
+
+	void __iomem *common_memory;
+
+	/* Reference to attribute memory, containing CIS data */
+	void *attribute_memory;
+
+	/* Hardware context */
+	struct ipw_hardware *hardware;
+	/* Network layer context */
+	struct ipw_network *network;
+	/* TTY device context */
+	struct ipw_tty *tty;
+	struct work_struct work_reboot;
+};
+
+/* Module parametres */
+extern int ipwireless_debug;
+extern int ipwireless_loopback;
+extern int ipwireless_out_queue;
+
+#endif

drivers/tty/ipwireless/network.c

@@ -0,0 +1,508 @@
+/*
+ * IPWireless 3G PCMCIA Network Driver
+ *
+ * Original code
+ *   by Stephen Blackheath <stephen@blacksapphire.com>,
+ *      Ben Martel <benm@symmetric.co.nz>
+ *
+ * Copyrighted as follows:
+ *   Copyright (C) 2004 by Symmetric Systems Ltd (NZ)
+ *
+ * Various driver changes and rewrites, port to new kernels
+ *   Copyright (C) 2006-2007 Jiri Kosina
+ *
+ * Misc code cleanups and updates
+ *   Copyright (C) 2007 David Sterba
+ */
+
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <linux/mutex.h>
+#include <linux/netdevice.h>
+#include <linux/ppp_channel.h>
+#include <linux/ppp_defs.h>
+#include <linux/slab.h>
+#include <linux/if_ppp.h>
+#include <linux/skbuff.h>
+
+#include "network.h"
+#include "hardware.h"
+#include "main.h"
+#include "tty.h"
+
+#define MAX_ASSOCIATED_TTYS 2
+
+#define SC_RCV_BITS     (SC_RCV_B7_1|SC_RCV_B7_0|SC_RCV_ODDP|SC_RCV_EVNP)
+
+struct ipw_network {
+	/* Hardware context, used for calls to hardware layer. */
+	struct ipw_hardware *hardware;
+	/* Context for kernel 'generic_ppp' functionality */
+	struct ppp_channel *ppp_channel;
+	/* tty context connected with IPW console */
+	struct ipw_tty *associated_ttys[NO_OF_IPW_CHANNELS][MAX_ASSOCIATED_TTYS];
+	/* True if ppp needs waking up once we're ready to xmit */
+	int ppp_blocked;
+	/* Number of packets queued up in hardware module. */
+	int outgoing_packets_queued;
+	/* Spinlock to avoid interrupts during shutdown */
+	spinlock_t lock;
+	struct mutex close_lock;
+
+	/* PPP ioctl data, not actually used anywere */
+	unsigned int flags;
+	unsigned int rbits;
+	u32 xaccm[8];
+	u32 raccm;
+	int mru;
+
+	int shutting_down;
+	unsigned int ras_control_lines;
+
+	struct work_struct work_go_online;
+	struct work_struct work_go_offline;
+};
+
+static void notify_packet_sent(void *callback_data, unsigned int packet_length)
+{
+	struct ipw_network *network = callback_data;
+	unsigned long flags;
+
+	spin_lock_irqsave(&network->lock, flags);
+	network->outgoing_packets_queued--;
+	if (network->ppp_channel != NULL) {
+		if (network->ppp_blocked) {
+			network->ppp_blocked = 0;
+			spin_unlock_irqrestore(&network->lock, flags);
+			ppp_output_wakeup(network->ppp_channel);
+			if (ipwireless_debug)
+				printk(KERN_DEBUG IPWIRELESS_PCCARD_NAME
+				       ": ppp unblocked\n");
+		} else
+			spin_unlock_irqrestore(&network->lock, flags);
+	} else
+		spin_unlock_irqrestore(&network->lock, flags);
+}
+
+/*
+ * Called by the ppp system when it has a packet to send to the hardware.
+ */
+static int ipwireless_ppp_start_xmit(struct ppp_channel *ppp_channel,
+				     struct sk_buff *skb)
+{
+	struct ipw_network *network = ppp_channel->private;
+	unsigned long flags;
+
+	spin_lock_irqsave(&network->lock, flags);
+	if (network->outgoing_packets_queued < ipwireless_out_queue) {
+		unsigned char *buf;
+		static unsigned char header[] = {
+			PPP_ALLSTATIONS, /* 0xff */
+			PPP_UI,		 /* 0x03 */
+		};
+		int ret;
+
+		network->outgoing_packets_queued++;
+		spin_unlock_irqrestore(&network->lock, flags);
+
+		/*
+		 * If we have the requested amount of headroom in the skb we
+		 * were handed, then we can add the header efficiently.
+		 */
+		if (skb_headroom(skb) >= 2) {
+			memcpy(skb_push(skb, 2), header, 2);
+			ret = ipwireless_send_packet(network->hardware,
+					       IPW_CHANNEL_RAS, skb->data,
+					       skb->len,
+					       notify_packet_sent,
+					       network);
+			if (ret == -1) {
+				skb_pull(skb, 2);
+				return 0;
+			}
+		} else {
+			/* Otherwise (rarely) we do it inefficiently. */
+			buf = kmalloc(skb->len + 2, GFP_ATOMIC);
+			if (!buf)
+				return 0;
+			memcpy(buf + 2, skb->data, skb->len);
+			memcpy(buf, header, 2);
+			ret = ipwireless_send_packet(network->hardware,
+					       IPW_CHANNEL_RAS, buf,
+					       skb->len + 2,
+					       notify_packet_sent,
+					       network);
+			kfree(buf);
+			if (ret == -1)
+				return 0;
+		}
+		kfree_skb(skb);
+		return 1;
+	} else {
+		/*
+		 * Otherwise reject the packet, and flag that the ppp system
+		 * needs to be unblocked once we are ready to send.
+		 */
+		network->ppp_blocked = 1;
+		spin_unlock_irqrestore(&network->lock, flags);
+		if (ipwireless_debug)
+			printk(KERN_DEBUG IPWIRELESS_PCCARD_NAME ": ppp blocked\n");
+		return 0;
+	}
+}
+
+/* Handle an ioctl call that has come in via ppp. (copy of ppp_async_ioctl() */
+static int ipwireless_ppp_ioctl(struct ppp_channel *ppp_channel,
+				unsigned int cmd, unsigned long arg)
+{
+	struct ipw_network *network = ppp_channel->private;
+	int err, val;
+	u32 accm[8];
+	int __user *user_arg = (int __user *) arg;
+
+	err = -EFAULT;
+	switch (cmd) {
+	case PPPIOCGFLAGS:
+		val = network->flags | network->rbits;
+		if (put_user(val, user_arg))
+			break;
+		err = 0;
+		break;
+
+	case PPPIOCSFLAGS:
+		if (get_user(val, user_arg))
+			break;
+		network->flags = val & ~SC_RCV_BITS;
+		network->rbits = val & SC_RCV_BITS;
+		err = 0;
+		break;
+
+	case PPPIOCGASYNCMAP:
+		if (put_user(network->xaccm[0], user_arg))
+			break;
+		err = 0;
+		break;
+
+	case PPPIOCSASYNCMAP:
+		if (get_user(network->xaccm[0], user_arg))
+			break;
+		err = 0;
+		break;
+
+	case PPPIOCGRASYNCMAP:
+		if (put_user(network->raccm, user_arg))
+			break;
+		err = 0;
+		break;
+
+	case PPPIOCSRASYNCMAP:
+		if (get_user(network->raccm, user_arg))
+			break;
+		err = 0;
+		break;
+
+	case PPPIOCGXASYNCMAP:
+		if (copy_to_user((void __user *) arg, network->xaccm,
+					sizeof(network->xaccm)))
+			break;
+		err = 0;
+		break;
+
+	case PPPIOCSXASYNCMAP:
+		if (copy_from_user(accm, (void __user *) arg, sizeof(accm)))
+			break;
+		accm[2] &= ~0x40000000U;	/* can't escape 0x5e */
+		accm[3] |= 0x60000000U;	/* must escape 0x7d, 0x7e */
+		memcpy(network->xaccm, accm, sizeof(network->xaccm));
+		err = 0;
+		break;
+
+	case PPPIOCGMRU:
+		if (put_user(network->mru, user_arg))
+			break;
+		err = 0;
+		break;
+
+	case PPPIOCSMRU:
+		if (get_user(val, user_arg))
+			break;
+		if (val < PPP_MRU)
+			val = PPP_MRU;
+		network->mru = val;
+		err = 0;
+		break;
+
+	default:
+		err = -ENOTTY;
+	}
+
+	return err;
+}
+
+static const struct ppp_channel_ops ipwireless_ppp_channel_ops = {
+	.start_xmit = ipwireless_ppp_start_xmit,
+	.ioctl      = ipwireless_ppp_ioctl
+};
+
+static void do_go_online(struct work_struct *work_go_online)
+{
+	struct ipw_network *network =
+		container_of(work_go_online, struct ipw_network,
+				work_go_online);
+	unsigned long flags;
+
+	spin_lock_irqsave(&network->lock, flags);
+	if (!network->ppp_channel) {
+		struct ppp_channel *channel;
+
+		spin_unlock_irqrestore(&network->lock, flags);
+		channel = kzalloc(sizeof(struct ppp_channel), GFP_KERNEL);
+		if (!channel) {
+			printk(KERN_ERR IPWIRELESS_PCCARD_NAME
+					": unable to allocate PPP channel\n");
+			return;
+		}
+		channel->private = network;
+		channel->mtu = 16384;	/* Wild guess */
+		channel->hdrlen = 2;
+		channel->ops = &ipwireless_ppp_channel_ops;
+
+		network->flags = 0;
+		network->rbits = 0;
+		network->mru = PPP_MRU;
+		memset(network->xaccm, 0, sizeof(network->xaccm));
+		network->xaccm[0] = ~0U;
+		network->xaccm[3] = 0x60000000U;
+		network->raccm = ~0U;
+		ppp_register_channel(channel);
+		spin_lock_irqsave(&network->lock, flags);
+		network->ppp_channel = channel;
+	}
+	spin_unlock_irqrestore(&network->lock, flags);
+}
+
+static void do_go_offline(struct work_struct *work_go_offline)
+{
+	struct ipw_network *network =
+		container_of(work_go_offline, struct ipw_network,
+				work_go_offline);
+	unsigned long flags;
+
+	mutex_lock(&network->close_lock);
+	spin_lock_irqsave(&network->lock, flags);
+	if (network->ppp_channel != NULL) {
+		struct ppp_channel *channel = network->ppp_channel;
+
+		network->ppp_channel = NULL;
+		spin_unlock_irqrestore(&network->lock, flags);
+		mutex_unlock(&network->close_lock);
+		ppp_unregister_channel(channel);
+	} else {
+		spin_unlock_irqrestore(&network->lock, flags);
+		mutex_unlock(&network->close_lock);
+	}
+}
+
+void ipwireless_network_notify_control_line_change(struct ipw_network *network,
+						   unsigned int channel_idx,
+						   unsigned int control_lines,
+						   unsigned int changed_mask)
+{
+	int i;
+
+	if (channel_idx == IPW_CHANNEL_RAS)
+		network->ras_control_lines = control_lines;
+
+	for (i = 0; i < MAX_ASSOCIATED_TTYS; i++) {
+		struct ipw_tty *tty =
+			network->associated_ttys[channel_idx][i];
+
+		/*
+		 * If it's associated with a tty (other than the RAS channel
+		 * when we're online), then send the data to that tty.  The RAS
+		 * channel's data is handled above - it always goes through
+		 * ppp_generic.
+		 */
+		if (tty)
+			ipwireless_tty_notify_control_line_change(tty,
+								  channel_idx,
+								  control_lines,
+								  changed_mask);
+	}
+}
+
+/*
+ * Some versions of firmware stuff packets with 0xff 0x03 (PPP: ALLSTATIONS, UI)
+ * bytes, which are required on sent packet, but not always present on received
+ * packets
+ */
+static struct sk_buff *ipw_packet_received_skb(unsigned char *data,
+					       unsigned int length)
+{
+	struct sk_buff *skb;
+
+	if (length > 2 && data[0] == PPP_ALLSTATIONS && data[1] == PPP_UI) {
+		length -= 2;
+		data += 2;
+	}
+
+	skb = dev_alloc_skb(length + 4);
+	skb_reserve(skb, 2);
+	memcpy(skb_put(skb, length), data, length);
+
+	return skb;
+}
+
+void ipwireless_network_packet_received(struct ipw_network *network,
+					unsigned int channel_idx,
+					unsigned char *data,
+					unsigned int length)
+{
+	int i;
+	unsigned long flags;
+
+	for (i = 0; i < MAX_ASSOCIATED_TTYS; i++) {
+		struct ipw_tty *tty = network->associated_ttys[channel_idx][i];
+
+		if (!tty)
+			continue;
+
+		/*
+		 * If it's associated with a tty (other than the RAS channel
+		 * when we're online), then send the data to that tty.  The RAS
+		 * channel's data is handled above - it always goes through
+		 * ppp_generic.
+		 */
+		if (channel_idx == IPW_CHANNEL_RAS
+				&& (network->ras_control_lines &
+					IPW_CONTROL_LINE_DCD) != 0
+				&& ipwireless_tty_is_modem(tty)) {
+			/*
+			 * If data came in on the RAS channel and this tty is
+			 * the modem tty, and we are online, then we send it to
+			 * the PPP layer.
+			 */
+			mutex_lock(&network->close_lock);
+			spin_lock_irqsave(&network->lock, flags);
+			if (network->ppp_channel != NULL) {
+				struct sk_buff *skb;
+
+				spin_unlock_irqrestore(&network->lock,
+						flags);
+
+				/* Send the data to the ppp_generic module. */
+				skb = ipw_packet_received_skb(data, length);
+				ppp_input(network->ppp_channel, skb);
+			} else
+				spin_unlock_irqrestore(&network->lock,
+						flags);
+			mutex_unlock(&network->close_lock);
+		}
+		/* Otherwise we send it out the tty. */
+		else
+			ipwireless_tty_received(tty, data, length);
+	}
+}
+
+struct ipw_network *ipwireless_network_create(struct ipw_hardware *hw)
+{
+	struct ipw_network *network =
+		kzalloc(sizeof(struct ipw_network), GFP_ATOMIC);
+
+	if (!network)
+		return NULL;
+
+	spin_lock_init(&network->lock);
+	mutex_init(&network->close_lock);
+
+	network->hardware = hw;
+
+	INIT_WORK(&network->work_go_online, do_go_online);
+	INIT_WORK(&network->work_go_offline, do_go_offline);
+
+	ipwireless_associate_network(hw, network);
+
+	return network;
+}
+
+void ipwireless_network_free(struct ipw_network *network)
+{
+	network->shutting_down = 1;
+
+	ipwireless_ppp_close(network);
+	flush_work_sync(&network->work_go_online);
+	flush_work_sync(&network->work_go_offline);
+
+	ipwireless_stop_interrupts(network->hardware);
+	ipwireless_associate_network(network->hardware, NULL);
+
+	kfree(network);
+}
+
+void ipwireless_associate_network_tty(struct ipw_network *network,
+				      unsigned int channel_idx,
+				      struct ipw_tty *tty)
+{
+	int i;
+
+	for (i = 0; i < MAX_ASSOCIATED_TTYS; i++)
+		if (network->associated_ttys[channel_idx][i] == NULL) {
+			network->associated_ttys[channel_idx][i] = tty;
+			break;
+		}
+}
+
+void ipwireless_disassociate_network_ttys(struct ipw_network *network,
+					  unsigned int channel_idx)
+{
+	int i;
+
+	for (i = 0; i < MAX_ASSOCIATED_TTYS; i++)
+		network->associated_ttys[channel_idx][i] = NULL;
+}
+
+void ipwireless_ppp_open(struct ipw_network *network)
+{
+	if (ipwireless_debug)
+		printk(KERN_DEBUG IPWIRELESS_PCCARD_NAME ": online\n");
+	schedule_work(&network->work_go_online);
+}
+
+void ipwireless_ppp_close(struct ipw_network *network)
+{
+	/* Disconnect from the wireless network. */
+	if (ipwireless_debug)
+		printk(KERN_DEBUG IPWIRELESS_PCCARD_NAME ": offline\n");
+	schedule_work(&network->work_go_offline);
+}
+
+int ipwireless_ppp_channel_index(struct ipw_network *network)
+{
+	int ret = -1;
+	unsigned long flags;
+
+	spin_lock_irqsave(&network->lock, flags);
+	if (network->ppp_channel != NULL)
+		ret = ppp_channel_index(network->ppp_channel);
+	spin_unlock_irqrestore(&network->lock, flags);
+
+	return ret;
+}
+
+int ipwireless_ppp_unit_number(struct ipw_network *network)
+{
+	int ret = -1;
+	unsigned long flags;
+
+	spin_lock_irqsave(&network->lock, flags);
+	if (network->ppp_channel != NULL)
+		ret = ppp_unit_number(network->ppp_channel);
+	spin_unlock_irqrestore(&network->lock, flags);
+
+	return ret;
+}
+
+int ipwireless_ppp_mru(const struct ipw_network *network)
+{
+	return network->mru;
+}

drivers/tty/ipwireless/network.h

@@ -0,0 +1,53 @@
+/*
+ * IPWireless 3G PCMCIA Network Driver
+ *
+ * Original code
+ *   by Stephen Blackheath <stephen@blacksapphire.com>,
+ *      Ben Martel <benm@symmetric.co.nz>
+ *
+ * Copyrighted as follows:
+ *   Copyright (C) 2004 by Symmetric Systems Ltd (NZ)
+ *
+ * Various driver changes and rewrites, port to new kernels
+ *   Copyright (C) 2006-2007 Jiri Kosina
+ *
+ * Misc code cleanups and updates
+ *   Copyright (C) 2007 David Sterba
+ */
+
+#ifndef _IPWIRELESS_CS_NETWORK_H_
+#define _IPWIRELESS_CS_NETWORK_H_
+
+#include <linux/types.h>
+
+struct ipw_network;
+struct ipw_tty;
+struct ipw_hardware;
+
+/* Definitions of the different channels on the PCMCIA UE */
+#define IPW_CHANNEL_RAS      0
+#define IPW_CHANNEL_DIALLER  1
+#define IPW_CHANNEL_CONSOLE  2
+#define NO_OF_IPW_CHANNELS   5
+
+void ipwireless_network_notify_control_line_change(struct ipw_network *net,
+		unsigned int channel_idx, unsigned int control_lines,
+		unsigned int control_mask);
+void ipwireless_network_packet_received(struct ipw_network *net,
+		unsigned int channel_idx, unsigned char *data,
+		unsigned int length);
+struct ipw_network *ipwireless_network_create(struct ipw_hardware *hw);
+void ipwireless_network_free(struct ipw_network *net);
+void ipwireless_associate_network_tty(struct ipw_network *net,
+		unsigned int channel_idx, struct ipw_tty *tty);
+void ipwireless_disassociate_network_ttys(struct ipw_network *net,
+		unsigned int channel_idx);
+
+void ipwireless_ppp_open(struct ipw_network *net);
+
+void ipwireless_ppp_close(struct ipw_network *net);
+int ipwireless_ppp_channel_index(struct ipw_network *net);
+int ipwireless_ppp_unit_number(struct ipw_network *net);
+int ipwireless_ppp_mru(const struct ipw_network *net);
+
+#endif

drivers/tty/ipwireless/setup_protocol.h

@@ -0,0 +1,108 @@
+/*
+ * IPWireless 3G PCMCIA Network Driver
+ *
+ * Original code
+ *   by Stephen Blackheath <stephen@blacksapphire.com>,
+ *      Ben Martel <benm@symmetric.co.nz>
+ *
+ * Copyrighted as follows:
+ *   Copyright (C) 2004 by Symmetric Systems Ltd (NZ)
+ *
+ * Various driver changes and rewrites, port to new kernels
+ *   Copyright (C) 2006-2007 Jiri Kosina
+ *
+ * Misc code cleanups and updates
+ *   Copyright (C) 2007 David Sterba
+ */
+
+#ifndef _IPWIRELESS_CS_SETUP_PROTOCOL_H_
+#define _IPWIRELESS_CS_SETUP_PROTOCOL_H_
+
+/* Version of the setup protocol and transport protocols */
+#define TL_SETUP_VERSION		1
+
+#define TL_SETUP_VERSION_QRY_TMO	1000
+#define TL_SETUP_MAX_VERSION_QRY	30
+
+/* Message numbers 0-9 are obsoleted and must not be reused! */
+#define TL_SETUP_SIGNO_GET_VERSION_QRY	10
+#define TL_SETUP_SIGNO_GET_VERSION_RSP	11
+#define TL_SETUP_SIGNO_CONFIG_MSG	12
+#define TL_SETUP_SIGNO_CONFIG_DONE_MSG	13
+#define TL_SETUP_SIGNO_OPEN_MSG		14
+#define TL_SETUP_SIGNO_CLOSE_MSG	15
+
+#define TL_SETUP_SIGNO_INFO_MSG     20
+#define TL_SETUP_SIGNO_INFO_MSG_ACK 21
+
+#define TL_SETUP_SIGNO_REBOOT_MSG      22
+#define TL_SETUP_SIGNO_REBOOT_MSG_ACK  23
+
+/* Synchronous start-messages */
+struct tl_setup_get_version_qry {
+	unsigned char sig_no;		/* TL_SETUP_SIGNO_GET_VERSION_QRY */
+} __attribute__ ((__packed__));
+
+struct tl_setup_get_version_rsp {
+	unsigned char sig_no;		/* TL_SETUP_SIGNO_GET_VERSION_RSP */
+	unsigned char version;		/* TL_SETUP_VERSION */
+} __attribute__ ((__packed__));
+
+struct tl_setup_config_msg {
+	unsigned char sig_no;		/* TL_SETUP_SIGNO_CONFIG_MSG */
+	unsigned char port_no;
+	unsigned char prio_data;
+	unsigned char prio_ctrl;
+} __attribute__ ((__packed__));
+
+struct tl_setup_config_done_msg {
+	unsigned char sig_no;		/* TL_SETUP_SIGNO_CONFIG_DONE_MSG */
+} __attribute__ ((__packed__));
+
+/* Asyncronous messages */
+struct tl_setup_open_msg {
+	unsigned char sig_no;		/* TL_SETUP_SIGNO_OPEN_MSG */
+	unsigned char port_no;
+} __attribute__ ((__packed__));
+
+struct tl_setup_close_msg {
+	unsigned char sig_no;		/* TL_SETUP_SIGNO_CLOSE_MSG */
+	unsigned char port_no;
+} __attribute__ ((__packed__));
+
+/* Driver type  - for use in tl_setup_info_msg.driver_type */
+#define COMM_DRIVER     0
+#define NDISWAN_DRIVER  1
+#define NDISWAN_DRIVER_MAJOR_VERSION  2
+#define NDISWAN_DRIVER_MINOR_VERSION  0
+
+/*
+ * It should not matter when this message comes over as we just store the
+ * results and send the ACK.
+ */
+struct tl_setup_info_msg {
+	unsigned char sig_no;		/* TL_SETUP_SIGNO_INFO_MSG */
+	unsigned char driver_type;
+	unsigned char major_version;
+	unsigned char minor_version;
+} __attribute__ ((__packed__));
+
+struct tl_setup_info_msgAck {
+	unsigned char sig_no;		/* TL_SETUP_SIGNO_INFO_MSG_ACK */
+} __attribute__ ((__packed__));
+
+struct TlSetupRebootMsgAck {
+	unsigned char sig_no;		/* TL_SETUP_SIGNO_REBOOT_MSG_ACK */
+} __attribute__ ((__packed__));
+
+/* Define a union of all the msgs that the driver can receive from the card.*/
+union ipw_setup_rx_msg {
+	unsigned char sig_no;
+	struct tl_setup_get_version_rsp version_rsp_msg;
+	struct tl_setup_open_msg open_msg;
+	struct tl_setup_close_msg close_msg;
+	struct tl_setup_info_msg InfoMsg;
+	struct tl_setup_info_msgAck info_msg_ack;
+} __attribute__ ((__packed__));
+
+#endif				/* _IPWIRELESS_CS_SETUP_PROTOCOL_H_ */

drivers/tty/ipwireless/tty.c

@@ -0,0 +1,679 @@
+/*
+ * IPWireless 3G PCMCIA Network Driver
+ *
+ * Original code
+ *   by Stephen Blackheath <stephen@blacksapphire.com>,
+ *      Ben Martel <benm@symmetric.co.nz>
+ *
+ * Copyrighted as follows:
+ *   Copyright (C) 2004 by Symmetric Systems Ltd (NZ)
+ *
+ * Various driver changes and rewrites, port to new kernels
+ *   Copyright (C) 2006-2007 Jiri Kosina
+ *
+ * Misc code cleanups and updates
+ *   Copyright (C) 2007 David Sterba
+ */
+
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/ppp_defs.h>
+#include <linux/if.h>
+#include <linux/if_ppp.h>
+#include <linux/sched.h>
+#include <linux/serial.h>
+#include <linux/slab.h>
+#include <linux/tty.h>
+#include <linux/tty_driver.h>
+#include <linux/tty_flip.h>
+#include <linux/uaccess.h>
+
+#include "tty.h"
+#include "network.h"
+#include "hardware.h"
+#include "main.h"
+
+#define IPWIRELESS_PCMCIA_START 	(0)
+#define IPWIRELESS_PCMCIA_MINORS	(24)
+#define IPWIRELESS_PCMCIA_MINOR_RANGE	(8)
+
+#define TTYTYPE_MODEM    (0)
+#define TTYTYPE_MONITOR  (1)
+#define TTYTYPE_RAS_RAW  (2)
+
+struct ipw_tty {
+	int index;
+	struct ipw_hardware *hardware;
+	unsigned int channel_idx;
+	unsigned int secondary_channel_idx;
+	int tty_type;
+	struct ipw_network *network;
+	struct tty_struct *linux_tty;
+	int open_count;
+	unsigned int control_lines;
+	struct mutex ipw_tty_mutex;
+	int tx_bytes_queued;
+	int closing;
+};
+
+static struct ipw_tty *ttys[IPWIRELESS_PCMCIA_MINORS];
+
+static struct tty_driver *ipw_tty_driver;
+
+static char *tty_type_name(int tty_type)
+{
+	static char *channel_names[] = {
+		"modem",
+		"monitor",
+		"RAS-raw"
+	};
+
+	return channel_names[tty_type];
+}
+
+static void report_registering(struct ipw_tty *tty)
+{
+	char *iftype = tty_type_name(tty->tty_type);
+
+	printk(KERN_INFO IPWIRELESS_PCCARD_NAME
+	       ": registering %s device ttyIPWp%d\n", iftype, tty->index);
+}
+
+static void report_deregistering(struct ipw_tty *tty)
+{
+	char *iftype = tty_type_name(tty->tty_type);
+
+	printk(KERN_INFO IPWIRELESS_PCCARD_NAME
+	       ": deregistering %s device ttyIPWp%d\n", iftype,
+	       tty->index);
+}
+
+static struct ipw_tty *get_tty(int minor)
+{
+	if (minor < ipw_tty_driver->minor_start
+			|| minor >= ipw_tty_driver->minor_start +
+			IPWIRELESS_PCMCIA_MINORS)
+		return NULL;
+	else {
+		int minor_offset = minor - ipw_tty_driver->minor_start;
+
+		/*
+		 * The 'ras_raw' channel is only available when 'loopback' mode
+		 * is enabled.
+		 * Number of minor starts with 16 (_RANGE * _RAS_RAW).
+		 */
+		if (!ipwireless_loopback &&
+				minor_offset >=
+				 IPWIRELESS_PCMCIA_MINOR_RANGE * TTYTYPE_RAS_RAW)
+			return NULL;
+
+		return ttys[minor_offset];
+	}
+}
+
+static int ipw_open(struct tty_struct *linux_tty, struct file *filp)
+{
+	int minor = linux_tty->index;
+	struct ipw_tty *tty = get_tty(minor);
+
+	if (!tty)
+		return -ENODEV;
+
+	mutex_lock(&tty->ipw_tty_mutex);
+
+	if (tty->closing) {
+		mutex_unlock(&tty->ipw_tty_mutex);
+		return -ENODEV;
+	}
+	if (tty->open_count == 0)
+		tty->tx_bytes_queued = 0;
+
+	tty->open_count++;
+
+	tty->linux_tty = linux_tty;
+	linux_tty->driver_data = tty;
+	linux_tty->low_latency = 1;
+
+	if (tty->tty_type == TTYTYPE_MODEM)
+		ipwireless_ppp_open(tty->network);
+
+	mutex_unlock(&tty->ipw_tty_mutex);
+
+	return 0;
+}
+
+static void do_ipw_close(struct ipw_tty *tty)
+{
+	tty->open_count--;
+
+	if (tty->open_count == 0) {
+		struct tty_struct *linux_tty = tty->linux_tty;
+
+		if (linux_tty != NULL) {
+			tty->linux_tty = NULL;
+			linux_tty->driver_data = NULL;
+
+			if (tty->tty_type == TTYTYPE_MODEM)
+				ipwireless_ppp_close(tty->network);
+		}
+	}
+}
+
+static void ipw_hangup(struct tty_struct *linux_tty)
+{
+	struct ipw_tty *tty = linux_tty->driver_data;
+
+	if (!tty)
+		return;
+
+	mutex_lock(&tty->ipw_tty_mutex);
+	if (tty->open_count == 0) {
+		mutex_unlock(&tty->ipw_tty_mutex);
+		return;
+	}
+
+	do_ipw_close(tty);
+
+	mutex_unlock(&tty->ipw_tty_mutex);
+}
+
+static void ipw_close(struct tty_struct *linux_tty, struct file *filp)
+{
+	ipw_hangup(linux_tty);
+}
+
+/* Take data received from hardware, and send it out the tty */
+void ipwireless_tty_received(struct ipw_tty *tty, unsigned char *data,
+			unsigned int length)
+{
+	struct tty_struct *linux_tty;
+	int work = 0;
+
+	mutex_lock(&tty->ipw_tty_mutex);
+	linux_tty = tty->linux_tty;
+	if (linux_tty == NULL) {
+		mutex_unlock(&tty->ipw_tty_mutex);
+		return;
+	}
+
+	if (!tty->open_count) {
+		mutex_unlock(&tty->ipw_tty_mutex);
+		return;
+	}
+	mutex_unlock(&tty->ipw_tty_mutex);
+
+	work = tty_insert_flip_string(linux_tty, data, length);
+
+	if (work != length)
+		printk(KERN_DEBUG IPWIRELESS_PCCARD_NAME
+				": %d chars not inserted to flip buffer!\n",
+				length - work);
+
+	/*
+	 * This may sleep if ->low_latency is set
+	 */
+	if (work)
+		tty_flip_buffer_push(linux_tty);
+}
+
+static void ipw_write_packet_sent_callback(void *callback_data,
+					   unsigned int packet_length)
+{
+	struct ipw_tty *tty = callback_data;
+
+	/*
+	 * Packet has been sent, so we subtract the number of bytes from our
+	 * tally of outstanding TX bytes.
+	 */
+	tty->tx_bytes_queued -= packet_length;
+}
+
+static int ipw_write(struct tty_struct *linux_tty,
+		     const unsigned char *buf, int count)
+{
+	struct ipw_tty *tty = linux_tty->driver_data;
+	int room, ret;
+
+	if (!tty)
+		return -ENODEV;
+
+	mutex_lock(&tty->ipw_tty_mutex);
+	if (!tty->open_count) {
+		mutex_unlock(&tty->ipw_tty_mutex);
+		return -EINVAL;
+	}
+
+	room = IPWIRELESS_TX_QUEUE_SIZE - tty->tx_bytes_queued;
+	if (room < 0)
+		room = 0;
+	/* Don't allow caller to write any more than we have room for */
+	if (count > room)
+		count = room;
+
+	if (count == 0) {
+		mutex_unlock(&tty->ipw_tty_mutex);
+		return 0;
+	}
+
+	ret = ipwireless_send_packet(tty->hardware, IPW_CHANNEL_RAS,
+			       buf, count,
+			       ipw_write_packet_sent_callback, tty);
+	if (ret == -1) {
+		mutex_unlock(&tty->ipw_tty_mutex);
+		return 0;
+	}
+
+	tty->tx_bytes_queued += count;
+	mutex_unlock(&tty->ipw_tty_mutex);
+
+	return count;
+}
+
+static int ipw_write_room(struct tty_struct *linux_tty)
+{
+	struct ipw_tty *tty = linux_tty->driver_data;
+	int room;
+
+	/* FIXME: Exactly how is the tty object locked here .. */
+	if (!tty)
+		return -ENODEV;
+
+	if (!tty->open_count)
+		return -EINVAL;
+
+	room = IPWIRELESS_TX_QUEUE_SIZE - tty->tx_bytes_queued;
+	if (room < 0)
+		room = 0;
+
+	return room;
+}
+
+static int ipwireless_get_serial_info(struct ipw_tty *tty,
+				      struct serial_struct __user *retinfo)
+{
+	struct serial_struct tmp;
+
+	if (!retinfo)
+		return (-EFAULT);
+
+	memset(&tmp, 0, sizeof(tmp));
+	tmp.type = PORT_UNKNOWN;
+	tmp.line = tty->index;
+	tmp.port = 0;
+	tmp.irq = 0;
+	tmp.flags = 0;
+	tmp.baud_base = 115200;
+	tmp.close_delay = 0;
+	tmp.closing_wait = 0;
+	tmp.custom_divisor = 0;
+	tmp.hub6 = 0;
+	if (copy_to_user(retinfo, &tmp, sizeof(*retinfo)))
+		return -EFAULT;
+
+	return 0;
+}
+
+static int ipw_chars_in_buffer(struct tty_struct *linux_tty)
+{
+	struct ipw_tty *tty = linux_tty->driver_data;
+
+	if (!tty)
+		return 0;
+
+	if (!tty->open_count)
+		return 0;
+
+	return tty->tx_bytes_queued;
+}
+
+static int get_control_lines(struct ipw_tty *tty)
+{
+	unsigned int my = tty->control_lines;
+	unsigned int out = 0;
+
+	if (my & IPW_CONTROL_LINE_RTS)
+		out |= TIOCM_RTS;
+	if (my & IPW_CONTROL_LINE_DTR)
+		out |= TIOCM_DTR;
+	if (my & IPW_CONTROL_LINE_CTS)
+		out |= TIOCM_CTS;
+	if (my & IPW_CONTROL_LINE_DSR)
+		out |= TIOCM_DSR;
+	if (my & IPW_CONTROL_LINE_DCD)
+		out |= TIOCM_CD;
+
+	return out;
+}
+
+static int set_control_lines(struct ipw_tty *tty, unsigned int set,
+			     unsigned int clear)
+{
+	int ret;
+
+	if (set & TIOCM_RTS) {
+		ret = ipwireless_set_RTS(tty->hardware, tty->channel_idx, 1);
+		if (ret)
+			return ret;
+		if (tty->secondary_channel_idx != -1) {
+			ret = ipwireless_set_RTS(tty->hardware,
+					  tty->secondary_channel_idx, 1);
+			if (ret)
+				return ret;
+		}
+	}
+	if (set & TIOCM_DTR) {
+		ret = ipwireless_set_DTR(tty->hardware, tty->channel_idx, 1);
+		if (ret)
+			return ret;
+		if (tty->secondary_channel_idx != -1) {
+			ret = ipwireless_set_DTR(tty->hardware,
+					  tty->secondary_channel_idx, 1);
+			if (ret)
+				return ret;
+		}
+	}
+	if (clear & TIOCM_RTS) {
+		ret = ipwireless_set_RTS(tty->hardware, tty->channel_idx, 0);
+		if (tty->secondary_channel_idx != -1) {
+			ret = ipwireless_set_RTS(tty->hardware,
+					  tty->secondary_channel_idx, 0);
+			if (ret)
+				return ret;
+		}
+	}
+	if (clear & TIOCM_DTR) {
+		ret = ipwireless_set_DTR(tty->hardware, tty->channel_idx, 0);
+		if (tty->secondary_channel_idx != -1) {
+			ret = ipwireless_set_DTR(tty->hardware,
+					  tty->secondary_channel_idx, 0);
+			if (ret)
+				return ret;
+		}
+	}
+	return 0;
+}
+
+static int ipw_tiocmget(struct tty_struct *linux_tty)
+{
+	struct ipw_tty *tty = linux_tty->driver_data;
+	/* FIXME: Exactly how is the tty object locked here .. */
+
+	if (!tty)
+		return -ENODEV;
+
+	if (!tty->open_count)
+		return -EINVAL;
+
+	return get_control_lines(tty);
+}
+
+static int
+ipw_tiocmset(struct tty_struct *linux_tty,
+	     unsigned int set, unsigned int clear)
+{
+	struct ipw_tty *tty = linux_tty->driver_data;
+	/* FIXME: Exactly how is the tty object locked here .. */
+
+	if (!tty)
+		return -ENODEV;
+
+	if (!tty->open_count)
+		return -EINVAL;
+
+	return set_control_lines(tty, set, clear);
+}
+
+static int ipw_ioctl(struct tty_struct *linux_tty,
+		     unsigned int cmd, unsigned long arg)
+{
+	struct ipw_tty *tty = linux_tty->driver_data;
+
+	if (!tty)
+		return -ENODEV;
+
+	if (!tty->open_count)
+		return -EINVAL;
+
+	/* FIXME: Exactly how is the tty object locked here .. */
+
+	switch (cmd) {
+	case TIOCGSERIAL:
+		return ipwireless_get_serial_info(tty, (void __user *) arg);
+
+	case TIOCSSERIAL:
+		return 0;	/* Keeps the PCMCIA scripts happy. */
+	}
+
+	if (tty->tty_type == TTYTYPE_MODEM) {
+		switch (cmd) {
+		case PPPIOCGCHAN:
+			{
+				int chan = ipwireless_ppp_channel_index(
+							tty->network);
+
+				if (chan < 0)
+					return -ENODEV;
+				if (put_user(chan, (int __user *) arg))
+					return -EFAULT;
+			}
+			return 0;
+
+		case PPPIOCGUNIT:
+			{
+				int unit = ipwireless_ppp_unit_number(
+						tty->network);
+
+				if (unit < 0)
+					return -ENODEV;
+				if (put_user(unit, (int __user *) arg))
+					return -EFAULT;
+			}
+			return 0;
+
+		case FIONREAD:
+			{
+				int val = 0;
+
+				if (put_user(val, (int __user *) arg))
+					return -EFAULT;
+			}
+			return 0;
+		case TCFLSH:
+			return tty_perform_flush(linux_tty, arg);
+		}
+	}
+	return -ENOIOCTLCMD;
+}
+
+static int add_tty(int j,
+		    struct ipw_hardware *hardware,
+		    struct ipw_network *network, int channel_idx,
+		    int secondary_channel_idx, int tty_type)
+{
+	ttys[j] = kzalloc(sizeof(struct ipw_tty), GFP_KERNEL);
+	if (!ttys[j])
+		return -ENOMEM;
+	ttys[j]->index = j;
+	ttys[j]->hardware = hardware;
+	ttys[j]->channel_idx = channel_idx;
+	ttys[j]->secondary_channel_idx = secondary_channel_idx;
+	ttys[j]->network = network;
+	ttys[j]->tty_type = tty_type;
+	mutex_init(&ttys[j]->ipw_tty_mutex);
+
+	tty_register_device(ipw_tty_driver, j, NULL);
+	ipwireless_associate_network_tty(network, channel_idx, ttys[j]);
+
+	if (secondary_channel_idx != -1)
+		ipwireless_associate_network_tty(network,
+						 secondary_channel_idx,
+						 ttys[j]);
+	if (get_tty(j + ipw_tty_driver->minor_start) == ttys[j])
+		report_registering(ttys[j]);
+	return 0;
+}
+
+struct ipw_tty *ipwireless_tty_create(struct ipw_hardware *hardware,
+				      struct ipw_network *network)
+{
+	int i, j;
+
+	for (i = 0; i < IPWIRELESS_PCMCIA_MINOR_RANGE; i++) {
+		int allfree = 1;
+
+		for (j = i; j < IPWIRELESS_PCMCIA_MINORS;
+				j += IPWIRELESS_PCMCIA_MINOR_RANGE)
+			if (ttys[j] != NULL) {
+				allfree = 0;
+				break;
+			}
+
+		if (allfree) {
+			j = i;
+
+			if (add_tty(j, hardware, network,
+					IPW_CHANNEL_DIALLER, IPW_CHANNEL_RAS,
+					TTYTYPE_MODEM))
+				return NULL;
+
+			j += IPWIRELESS_PCMCIA_MINOR_RANGE;
+			if (add_tty(j, hardware, network,
+					IPW_CHANNEL_DIALLER, -1,
+					TTYTYPE_MONITOR))
+				return NULL;
+
+			j += IPWIRELESS_PCMCIA_MINOR_RANGE;
+			if (add_tty(j, hardware, network,
+					IPW_CHANNEL_RAS, -1,
+					TTYTYPE_RAS_RAW))
+				return NULL;
+
+			return ttys[i];
+		}
+	}
+	return NULL;
+}
+
+/*
+ * Must be called before ipwireless_network_free().
+ */
+void ipwireless_tty_free(struct ipw_tty *tty)
+{
+	int j;
+	struct ipw_network *network = ttys[tty->index]->network;
+
+	for (j = tty->index; j < IPWIRELESS_PCMCIA_MINORS;
+			j += IPWIRELESS_PCMCIA_MINOR_RANGE) {
+		struct ipw_tty *ttyj = ttys[j];
+
+		if (ttyj) {
+			mutex_lock(&ttyj->ipw_tty_mutex);
+			if (get_tty(j + ipw_tty_driver->minor_start) == ttyj)
+				report_deregistering(ttyj);
+			ttyj->closing = 1;
+			if (ttyj->linux_tty != NULL) {
+				mutex_unlock(&ttyj->ipw_tty_mutex);
+				tty_hangup(ttyj->linux_tty);
+				/* Wait till the tty_hangup has completed */
+				flush_work_sync(&ttyj->linux_tty->hangup_work);
+				/* FIXME: Exactly how is the tty object locked here
+				   against a parallel ioctl etc */
+				mutex_lock(&ttyj->ipw_tty_mutex);
+			}
+			while (ttyj->open_count)
+				do_ipw_close(ttyj);
+			ipwireless_disassociate_network_ttys(network,
+							     ttyj->channel_idx);
+			tty_unregister_device(ipw_tty_driver, j);
+			ttys[j] = NULL;
+			mutex_unlock(&ttyj->ipw_tty_mutex);
+			kfree(ttyj);
+		}
+	}
+}
+
+static const struct tty_operations tty_ops = {
+	.open = ipw_open,
+	.close = ipw_close,
+	.hangup = ipw_hangup,
+	.write = ipw_write,
+	.write_room = ipw_write_room,
+	.ioctl = ipw_ioctl,
+	.chars_in_buffer = ipw_chars_in_buffer,
+	.tiocmget = ipw_tiocmget,
+	.tiocmset = ipw_tiocmset,
+};
+
+int ipwireless_tty_init(void)
+{
+	int result;
+
+	ipw_tty_driver = alloc_tty_driver(IPWIRELESS_PCMCIA_MINORS);
+	if (!ipw_tty_driver)
+		return -ENOMEM;
+
+	ipw_tty_driver->owner = THIS_MODULE;
+	ipw_tty_driver->driver_name = IPWIRELESS_PCCARD_NAME;
+	ipw_tty_driver->name = "ttyIPWp";
+	ipw_tty_driver->major = 0;
+	ipw_tty_driver->minor_start = IPWIRELESS_PCMCIA_START;
+	ipw_tty_driver->type = TTY_DRIVER_TYPE_SERIAL;
+	ipw_tty_driver->subtype = SERIAL_TYPE_NORMAL;
+	ipw_tty_driver->flags = TTY_DRIVER_REAL_RAW | TTY_DRIVER_DYNAMIC_DEV;
+	ipw_tty_driver->init_termios = tty_std_termios;
+	ipw_tty_driver->init_termios.c_cflag =
+	    B9600 | CS8 | CREAD | HUPCL | CLOCAL;
+	ipw_tty_driver->init_termios.c_ispeed = 9600;
+	ipw_tty_driver->init_termios.c_ospeed = 9600;
+	tty_set_operations(ipw_tty_driver, &tty_ops);
+	result = tty_register_driver(ipw_tty_driver);
+	if (result) {
+		printk(KERN_ERR IPWIRELESS_PCCARD_NAME
+		       ": failed to register tty driver\n");
+		put_tty_driver(ipw_tty_driver);
+		return result;
+	}
+
+	return 0;
+}
+
+void ipwireless_tty_release(void)
+{
+	int ret;
+
+	ret = tty_unregister_driver(ipw_tty_driver);
+	put_tty_driver(ipw_tty_driver);
+	if (ret != 0)
+		printk(KERN_ERR IPWIRELESS_PCCARD_NAME
+			": tty_unregister_driver failed with code %d\n", ret);
+}
+
+int ipwireless_tty_is_modem(struct ipw_tty *tty)
+{
+	return tty->tty_type == TTYTYPE_MODEM;
+}
+
+void
+ipwireless_tty_notify_control_line_change(struct ipw_tty *tty,
+					  unsigned int channel_idx,
+					  unsigned int control_lines,
+					  unsigned int changed_mask)
+{
+	unsigned int old_control_lines = tty->control_lines;
+
+	tty->control_lines = (tty->control_lines & ~changed_mask)
+		| (control_lines & changed_mask);
+
+	/*
+	 * If DCD is de-asserted, we close the tty so pppd can tell that we
+	 * have gone offline.
+	 */
+	if ((old_control_lines & IPW_CONTROL_LINE_DCD)
+			&& !(tty->control_lines & IPW_CONTROL_LINE_DCD)
+			&& tty->linux_tty) {
+		tty_hangup(tty->linux_tty);
+	}
+}
+

drivers/tty/ipwireless/tty.h

@@ -0,0 +1,45 @@
+/*
+ * IPWireless 3G PCMCIA Network Driver
+ *
+ * Original code
+ *   by Stephen Blackheath <stephen@blacksapphire.com>,
+ *      Ben Martel <benm@symmetric.co.nz>
+ *
+ * Copyrighted as follows:
+ *   Copyright (C) 2004 by Symmetric Systems Ltd (NZ)
+ *
+ * Various driver changes and rewrites, port to new kernels
+ *   Copyright (C) 2006-2007 Jiri Kosina
+ *
+ * Misc code cleanups and updates
+ *   Copyright (C) 2007 David Sterba
+ */
+
+#ifndef _IPWIRELESS_CS_TTY_H_
+#define _IPWIRELESS_CS_TTY_H_
+
+#include <linux/types.h>
+#include <linux/sched.h>
+
+#include <pcmcia/cistpl.h>
+#include <pcmcia/ds.h>
+
+struct ipw_tty;
+struct ipw_network;
+struct ipw_hardware;
+
+int ipwireless_tty_init(void);
+void ipwireless_tty_release(void);
+
+struct ipw_tty *ipwireless_tty_create(struct ipw_hardware *hw,
+				      struct ipw_network *net);
+void ipwireless_tty_free(struct ipw_tty *tty);
+void ipwireless_tty_received(struct ipw_tty *tty, unsigned char *data,
+			     unsigned int length);
+int ipwireless_tty_is_modem(struct ipw_tty *tty);
+void ipwireless_tty_notify_control_line_change(struct ipw_tty *tty,
+					       unsigned int channel_idx,
+					       unsigned int control_lines,
+					       unsigned int changed_mask);
+
+#endif

drivers/tty/moxa.h

@@ -0,0 +1,304 @@
+#ifndef MOXA_H_FILE
+#define MOXA_H_FILE
+
+#define	MOXA		0x400
+#define MOXA_GET_IQUEUE 	(MOXA + 1)	/* get input buffered count */
+#define MOXA_GET_OQUEUE 	(MOXA + 2)	/* get output buffered count */
+#define MOXA_GETDATACOUNT       (MOXA + 23)
+#define MOXA_GET_IOQUEUE	(MOXA + 27)
+#define MOXA_FLUSH_QUEUE	(MOXA + 28)
+#define MOXA_GETMSTATUS         (MOXA + 65)
+
+/*
+ *    System Configuration
+ */
+
+#define Magic_code	0x404
+
+/*
+ *    for C218 BIOS initialization
+ */
+#define C218_ConfBase	0x800
+#define C218_status	(C218_ConfBase + 0)	/* BIOS running status    */
+#define C218_diag	(C218_ConfBase + 2)	/* diagnostic status      */
+#define C218_key	(C218_ConfBase + 4)	/* WORD (0x218 for C218) */
+#define C218DLoad_len	(C218_ConfBase + 6)	/* WORD           */
+#define C218check_sum	(C218_ConfBase + 8)	/* BYTE           */
+#define C218chksum_ok	(C218_ConfBase + 0x0a)	/* BYTE (1:ok)            */
+#define C218_TestRx	(C218_ConfBase + 0x10)	/* 8 bytes for 8 ports    */
+#define C218_TestTx	(C218_ConfBase + 0x18)	/* 8 bytes for 8 ports    */
+#define C218_RXerr	(C218_ConfBase + 0x20)	/* 8 bytes for 8 ports    */
+#define C218_ErrFlag	(C218_ConfBase + 0x28)	/* 8 bytes for 8 ports    */
+
+#define C218_LoadBuf	0x0F00
+#define C218_KeyCode	0x218
+#define CP204J_KeyCode	0x204
+
+/*
+ *    for C320 BIOS initialization
+ */
+#define C320_ConfBase	0x800
+#define C320_LoadBuf	0x0f00
+#define STS_init	0x05	/* for C320_status        */
+
+#define C320_status	C320_ConfBase + 0	/* BIOS running status    */
+#define C320_diag	C320_ConfBase + 2	/* diagnostic status      */
+#define C320_key	C320_ConfBase + 4	/* WORD (0320H for C320) */
+#define C320DLoad_len	C320_ConfBase + 6	/* WORD           */
+#define C320check_sum	C320_ConfBase + 8	/* WORD           */
+#define C320chksum_ok	C320_ConfBase + 0x0a	/* WORD (1:ok)            */
+#define C320bapi_len	C320_ConfBase + 0x0c	/* WORD           */
+#define C320UART_no	C320_ConfBase + 0x0e	/* WORD           */
+
+#define C320_KeyCode	0x320
+
+#define FixPage_addr	0x0000	/* starting addr of static page  */
+#define DynPage_addr	0x2000	/* starting addr of dynamic page */
+#define C218_start	0x3000	/* starting addr of C218 BIOS prg */
+#define Control_reg	0x1ff0	/* select page and reset control */
+#define HW_reset	0x80
+
+/*
+ *    Function Codes
+ */
+#define FC_CardReset	0x80
+#define FC_ChannelReset 1	/* C320 firmware not supported */
+#define FC_EnableCH	2
+#define FC_DisableCH	3
+#define FC_SetParam	4
+#define FC_SetMode	5
+#define FC_SetRate	6
+#define FC_LineControl	7
+#define FC_LineStatus	8
+#define FC_XmitControl	9
+#define FC_FlushQueue	10
+#define FC_SendBreak	11
+#define FC_StopBreak	12
+#define FC_LoopbackON	13
+#define FC_LoopbackOFF	14
+#define FC_ClrIrqTable	15
+#define FC_SendXon	16
+#define FC_SetTermIrq	17	/* C320 firmware not supported */
+#define FC_SetCntIrq	18	/* C320 firmware not supported */
+#define FC_SetBreakIrq	19
+#define FC_SetLineIrq	20
+#define FC_SetFlowCtl	21
+#define FC_GenIrq	22
+#define FC_InCD180	23
+#define FC_OutCD180	24
+#define FC_InUARTreg	23
+#define FC_OutUARTreg	24
+#define FC_SetXonXoff	25
+#define FC_OutCD180CCR	26
+#define FC_ExtIQueue	27
+#define FC_ExtOQueue	28
+#define FC_ClrLineIrq	29
+#define FC_HWFlowCtl	30
+#define FC_GetClockRate 35
+#define FC_SetBaud	36
+#define FC_SetDataMode  41
+#define FC_GetCCSR      43
+#define FC_GetDataError 45
+#define FC_RxControl	50
+#define FC_ImmSend	51
+#define FC_SetXonState	52
+#define FC_SetXoffState	53
+#define FC_SetRxFIFOTrig 54
+#define FC_SetTxFIFOCnt 55
+#define FC_UnixRate	56
+#define FC_UnixResetTimer 57
+
+#define	RxFIFOTrig1	0
+#define	RxFIFOTrig4	1
+#define	RxFIFOTrig8	2
+#define	RxFIFOTrig14	3
+
+/*
+ *    Dual-Ported RAM
+ */
+#define DRAM_global	0
+#define INT_data	(DRAM_global + 0)
+#define Config_base	(DRAM_global + 0x108)
+
+#define IRQindex	(INT_data + 0)
+#define IRQpending	(INT_data + 4)
+#define IRQtable	(INT_data + 8)
+
+/*
+ *    Interrupt Status
+ */
+#define IntrRx		0x01	/* receiver data O.K.             */
+#define IntrTx		0x02	/* transmit buffer empty  */
+#define IntrFunc	0x04	/* function complete              */
+#define IntrBreak	0x08	/* received break         */
+#define IntrLine	0x10	/* line status change
+				   for transmitter                */
+#define IntrIntr	0x20	/* received INTR code             */
+#define IntrQuit	0x40	/* received QUIT code             */
+#define IntrEOF 	0x80	/* received EOF code              */
+
+#define IntrRxTrigger 	0x100	/* rx data count reach tigger value */
+#define IntrTxTrigger 	0x200	/* tx data count below trigger value */
+
+#define Magic_no	(Config_base + 0)
+#define Card_model_no	(Config_base + 2)
+#define Total_ports	(Config_base + 4)
+#define Module_cnt	(Config_base + 8)
+#define Module_no	(Config_base + 10)
+#define Timer_10ms	(Config_base + 14)
+#define Disable_IRQ	(Config_base + 20)
+#define TMS320_PORT1	(Config_base + 22)
+#define TMS320_PORT2	(Config_base + 24)
+#define TMS320_CLOCK	(Config_base + 26)
+
+/*
+ *    DATA BUFFER in DRAM
+ */
+#define Extern_table	0x400	/* Base address of the external table
+				   (24 words *    64) total 3K bytes
+				   (24 words * 128) total 6K bytes */
+#define Extern_size	0x60	/* 96 bytes                       */
+#define RXrptr		0x00	/* read pointer for RX buffer     */
+#define RXwptr		0x02	/* write pointer for RX buffer    */
+#define TXrptr		0x04	/* read pointer for TX buffer     */
+#define TXwptr		0x06	/* write pointer for TX buffer    */
+#define HostStat	0x08	/* IRQ flag and general flag      */
+#define FlagStat	0x0A
+#define FlowControl	0x0C	/* B7 B6 B5 B4 B3 B2 B1 B0              */
+				/*  x  x  x  x  |  |  |  |            */
+				/*              |  |  |  + CTS flow   */
+				/*              |  |  +--- RTS flow   */
+				/*              |  +------ TX Xon/Xoff */
+				/*              +--------- RX Xon/Xoff */
+#define Break_cnt	0x0E	/* received break count   */
+#define CD180TXirq	0x10	/* if non-0: enable TX irq        */
+#define RX_mask 	0x12
+#define TX_mask 	0x14
+#define Ofs_rxb 	0x16
+#define Ofs_txb 	0x18
+#define Page_rxb	0x1A
+#define Page_txb	0x1C
+#define EndPage_rxb	0x1E
+#define EndPage_txb	0x20
+#define Data_error	0x22
+#define RxTrigger	0x28
+#define TxTrigger	0x2a
+
+#define rRXwptr 	0x34
+#define Low_water	0x36
+
+#define FuncCode	0x40
+#define FuncArg 	0x42
+#define FuncArg1	0x44
+
+#define C218rx_size	0x2000	/* 8K bytes */
+#define C218tx_size	0x8000	/* 32K bytes */
+
+#define C218rx_mask	(C218rx_size - 1)
+#define C218tx_mask	(C218tx_size - 1)
+
+#define C320p8rx_size	0x2000
+#define C320p8tx_size	0x8000
+#define C320p8rx_mask	(C320p8rx_size - 1)
+#define C320p8tx_mask	(C320p8tx_size - 1)
+
+#define C320p16rx_size	0x2000
+#define C320p16tx_size	0x4000
+#define C320p16rx_mask	(C320p16rx_size - 1)
+#define C320p16tx_mask	(C320p16tx_size - 1)
+
+#define C320p24rx_size	0x2000
+#define C320p24tx_size	0x2000
+#define C320p24rx_mask	(C320p24rx_size - 1)
+#define C320p24tx_mask	(C320p24tx_size - 1)
+
+#define C320p32rx_size	0x1000
+#define C320p32tx_size	0x1000
+#define C320p32rx_mask	(C320p32rx_size - 1)
+#define C320p32tx_mask	(C320p32tx_size - 1)
+
+#define Page_size	0x2000U
+#define Page_mask	(Page_size - 1)
+#define C218rx_spage	3
+#define C218tx_spage	4
+#define C218rx_pageno	1
+#define C218tx_pageno	4
+#define C218buf_pageno	5
+
+#define C320p8rx_spage	3
+#define C320p8tx_spage	4
+#define C320p8rx_pgno	1
+#define C320p8tx_pgno	4
+#define C320p8buf_pgno	5
+
+#define C320p16rx_spage 3
+#define C320p16tx_spage 4
+#define C320p16rx_pgno	1
+#define C320p16tx_pgno	2
+#define C320p16buf_pgno 3
+
+#define C320p24rx_spage 3
+#define C320p24tx_spage 4
+#define C320p24rx_pgno	1
+#define C320p24tx_pgno	1
+#define C320p24buf_pgno 2
+
+#define C320p32rx_spage 3
+#define C320p32tx_ofs	C320p32rx_size
+#define C320p32tx_spage 3
+#define C320p32buf_pgno 1
+
+/*
+ *    Host Status
+ */
+#define WakeupRx	0x01
+#define WakeupTx	0x02
+#define WakeupBreak	0x08
+#define WakeupLine	0x10
+#define WakeupIntr	0x20
+#define WakeupQuit	0x40
+#define WakeupEOF	0x80	/* used in VTIME control */
+#define WakeupRxTrigger	0x100
+#define WakeupTxTrigger	0x200
+/*
+ *    Flag status
+ */
+#define Rx_over		0x01
+#define Xoff_state	0x02
+#define Tx_flowOff	0x04
+#define Tx_enable	0x08
+#define CTS_state	0x10
+#define DSR_state	0x20
+#define DCD_state	0x80
+/*
+ *    FlowControl
+ */
+#define CTS_FlowCtl	1
+#define RTS_FlowCtl	2
+#define Tx_FlowCtl	4
+#define Rx_FlowCtl	8
+#define IXM_IXANY	0x10
+
+#define LowWater	128
+
+#define DTR_ON		1
+#define RTS_ON		2
+#define CTS_ON		1
+#define DSR_ON		2
+#define DCD_ON		8
+
+/* mode definition */
+#define	MX_CS8		0x03
+#define	MX_CS7		0x02
+#define	MX_CS6		0x01
+#define	MX_CS5		0x00
+
+#define	MX_STOP1	0x00
+#define	MX_STOP15	0x04
+#define	MX_STOP2	0x08
+
+#define	MX_PARNONE	0x00
+#define	MX_PAREVEN	0x40
+#define	MX_PARODD	0xC0
+
+#endif

drivers/tty/mxser.h

@@ -0,0 +1,150 @@
+#ifndef _MXSER_H
+#define _MXSER_H
+
+/*
+ *	Semi-public control interfaces
+ */
+
+/*
+ *	MOXA ioctls
+ */
+
+#define MOXA			0x400
+#define MOXA_GETDATACOUNT	(MOXA + 23)
+#define MOXA_DIAGNOSE		(MOXA + 50)
+#define MOXA_CHKPORTENABLE	(MOXA + 60)
+#define MOXA_HighSpeedOn	(MOXA + 61)
+#define MOXA_GET_MAJOR		(MOXA + 63)
+#define MOXA_GETMSTATUS		(MOXA + 65)
+#define MOXA_SET_OP_MODE	(MOXA + 66)
+#define MOXA_GET_OP_MODE	(MOXA + 67)
+
+#define RS232_MODE		0
+#define RS485_2WIRE_MODE	1
+#define RS422_MODE		2
+#define RS485_4WIRE_MODE	3
+#define OP_MODE_MASK		3
+
+#define MOXA_SDS_RSTICOUNTER	(MOXA + 69)
+#define MOXA_ASPP_OQUEUE  	(MOXA + 70)
+#define MOXA_ASPP_MON     	(MOXA + 73)
+#define MOXA_ASPP_LSTATUS 	(MOXA + 74)
+#define MOXA_ASPP_MON_EXT 	(MOXA + 75)
+#define MOXA_SET_BAUD_METHOD	(MOXA + 76)
+
+/* --------------------------------------------------- */
+
+#define NPPI_NOTIFY_PARITY	0x01
+#define NPPI_NOTIFY_FRAMING	0x02
+#define NPPI_NOTIFY_HW_OVERRUN	0x04
+#define NPPI_NOTIFY_SW_OVERRUN	0x08
+#define NPPI_NOTIFY_BREAK	0x10
+
+#define NPPI_NOTIFY_CTSHOLD         0x01	/* Tx hold by CTS low */
+#define NPPI_NOTIFY_DSRHOLD         0x02	/* Tx hold by DSR low */
+#define NPPI_NOTIFY_XOFFHOLD        0x08	/* Tx hold by Xoff received */
+#define NPPI_NOTIFY_XOFFXENT        0x10	/* Xoff Sent */
+
+/* follow just for Moxa Must chip define. */
+/* */
+/* when LCR register (offset 0x03) write following value, */
+/* the Must chip will enter enchance mode. And write value */
+/* on EFR (offset 0x02) bit 6,7 to change bank. */
+#define MOXA_MUST_ENTER_ENCHANCE	0xBF
+
+/* when enhance mode enable, access on general bank register */
+#define MOXA_MUST_GDL_REGISTER		0x07
+#define MOXA_MUST_GDL_MASK		0x7F
+#define MOXA_MUST_GDL_HAS_BAD_DATA	0x80
+
+#define MOXA_MUST_LSR_RERR		0x80	/* error in receive FIFO */
+/* enchance register bank select and enchance mode setting register */
+/* when LCR register equal to 0xBF */
+#define MOXA_MUST_EFR_REGISTER		0x02
+/* enchance mode enable */
+#define MOXA_MUST_EFR_EFRB_ENABLE	0x10
+/* enchance reister bank set 0, 1, 2 */
+#define MOXA_MUST_EFR_BANK0		0x00
+#define MOXA_MUST_EFR_BANK1		0x40
+#define MOXA_MUST_EFR_BANK2		0x80
+#define MOXA_MUST_EFR_BANK3		0xC0
+#define MOXA_MUST_EFR_BANK_MASK		0xC0
+
+/* set XON1 value register, when LCR=0xBF and change to bank0 */
+#define MOXA_MUST_XON1_REGISTER		0x04
+
+/* set XON2 value register, when LCR=0xBF and change to bank0 */
+#define MOXA_MUST_XON2_REGISTER		0x05
+
+/* set XOFF1 value register, when LCR=0xBF and change to bank0 */
+#define MOXA_MUST_XOFF1_REGISTER	0x06
+
+/* set XOFF2 value register, when LCR=0xBF and change to bank0 */
+#define MOXA_MUST_XOFF2_REGISTER	0x07
+
+#define MOXA_MUST_RBRTL_REGISTER	0x04
+#define MOXA_MUST_RBRTH_REGISTER	0x05
+#define MOXA_MUST_RBRTI_REGISTER	0x06
+#define MOXA_MUST_THRTL_REGISTER	0x07
+#define MOXA_MUST_ENUM_REGISTER		0x04
+#define MOXA_MUST_HWID_REGISTER		0x05
+#define MOXA_MUST_ECR_REGISTER		0x06
+#define MOXA_MUST_CSR_REGISTER		0x07
+
+/* good data mode enable */
+#define MOXA_MUST_FCR_GDA_MODE_ENABLE	0x20
+/* only good data put into RxFIFO */
+#define MOXA_MUST_FCR_GDA_ONLY_ENABLE	0x10
+
+/* enable CTS interrupt */
+#define MOXA_MUST_IER_ECTSI		0x80
+/* enable RTS interrupt */
+#define MOXA_MUST_IER_ERTSI		0x40
+/* enable Xon/Xoff interrupt */
+#define MOXA_MUST_IER_XINT		0x20
+/* enable GDA interrupt */
+#define MOXA_MUST_IER_EGDAI		0x10
+
+#define MOXA_MUST_RECV_ISR		(UART_IER_RDI | MOXA_MUST_IER_EGDAI)
+
+/* GDA interrupt pending */
+#define MOXA_MUST_IIR_GDA		0x1C
+#define MOXA_MUST_IIR_RDA		0x04
+#define MOXA_MUST_IIR_RTO		0x0C
+#define MOXA_MUST_IIR_LSR		0x06
+
+/* recieved Xon/Xoff or specical interrupt pending */
+#define MOXA_MUST_IIR_XSC		0x10
+
+/* RTS/CTS change state interrupt pending */
+#define MOXA_MUST_IIR_RTSCTS		0x20
+#define MOXA_MUST_IIR_MASK		0x3E
+
+#define MOXA_MUST_MCR_XON_FLAG		0x40
+#define MOXA_MUST_MCR_XON_ANY		0x80
+#define MOXA_MUST_MCR_TX_XON		0x08
+
+/* software flow control on chip mask value */
+#define MOXA_MUST_EFR_SF_MASK		0x0F
+/* send Xon1/Xoff1 */
+#define MOXA_MUST_EFR_SF_TX1		0x08
+/* send Xon2/Xoff2 */
+#define MOXA_MUST_EFR_SF_TX2		0x04
+/* send Xon1,Xon2/Xoff1,Xoff2 */
+#define MOXA_MUST_EFR_SF_TX12		0x0C
+/* don't send Xon/Xoff */
+#define MOXA_MUST_EFR_SF_TX_NO		0x00
+/* Tx software flow control mask */
+#define MOXA_MUST_EFR_SF_TX_MASK	0x0C
+/* don't receive Xon/Xoff */
+#define MOXA_MUST_EFR_SF_RX_NO		0x00
+/* receive Xon1/Xoff1 */
+#define MOXA_MUST_EFR_SF_RX1		0x02
+/* receive Xon2/Xoff2 */
+#define MOXA_MUST_EFR_SF_RX2		0x01
+/* receive Xon1,Xon2/Xoff1,Xoff2 */
+#define MOXA_MUST_EFR_SF_RX12		0x03
+/* Rx software flow control mask */
+#define MOXA_MUST_EFR_SF_RX_MASK	0x03
+
+#endif

drivers/tty/n_gsm.c

@@ -1250,8 +1250,7 @@ static void gsm_control_response(struct gsm_mux *gsm, unsigned int command,
 
 static void gsm_control_transmit(struct gsm_mux *gsm, struct gsm_control *ctrl)
 {
-	struct gsm_msg *msg = gsm_data_alloc(gsm, 0, ctrl->len + 1,
-							gsm->ftype|PF);
+	struct gsm_msg *msg = gsm_data_alloc(gsm, 0, ctrl->len + 1, gsm->ftype);
 	if (msg == NULL)
 		return;
 	msg->data[0] = (ctrl->cmd << 1) | 2 | EA;	/* command */
@@ -2649,13 +2648,13 @@ static void gsmtty_wait_until_sent(struct tty_struct *tty, int timeout)
 	   to do here */
 }
 
-static int gsmtty_tiocmget(struct tty_struct *tty, struct file *filp)
+static int gsmtty_tiocmget(struct tty_struct *tty)
 {
 	struct gsm_dlci *dlci = tty->driver_data;
 	return dlci->modem_rx;
 }
 
-static int gsmtty_tiocmset(struct tty_struct *tty, struct file *filp,
+static int gsmtty_tiocmset(struct tty_struct *tty,
 	unsigned int set, unsigned int clear)
 {
 	struct gsm_dlci *dlci = tty->driver_data;
@@ -2672,7 +2671,7 @@ static int gsmtty_tiocmset(struct tty_struct *tty, struct file *filp,
 }
 
 
-static int gsmtty_ioctl(struct tty_struct *tty, struct file *filp,
+static int gsmtty_ioctl(struct tty_struct *tty,
 			unsigned int cmd, unsigned long arg)
 {
 	return -ENOIOCTLCMD;

drivers/tty/n_hdlc.c

@@ -97,7 +97,6 @@
 #include <linux/slab.h>
 #include <linux/tty.h>
 #include <linux/errno.h>
-#include <linux/smp_lock.h>
 #include <linux/string.h>	/* used in new tty drivers */
 #include <linux/signal.h>	/* used in new tty drivers */
 #include <linux/if.h>

drivers/tty/n_r3964.c

@@ -57,7 +57,6 @@
 #include <linux/ioport.h>
 #include <linux/in.h>
 #include <linux/slab.h>
-#include <linux/smp_lock.h>
 #include <linux/tty.h>
 #include <linux/errno.h>
 #include <linux/string.h>	/* used in new tty drivers */

drivers/tty/pty.c

@@ -23,7 +23,6 @@
 #include <linux/major.h>
 #include <linux/mm.h>
 #include <linux/init.h>
-#include <linux/smp_lock.h>
 #include <linux/sysctl.h>
 #include <linux/device.h>
 #include <linux/uaccess.h>
@@ -334,7 +333,7 @@ free_mem_out:
 	return -ENOMEM;
 }
 
-static int pty_bsd_ioctl(struct tty_struct *tty, struct file *file,
+static int pty_bsd_ioctl(struct tty_struct *tty,
 			 unsigned int cmd, unsigned long arg)
 {
 	switch (cmd) {
@@ -489,7 +488,7 @@ static struct ctl_table pty_root_table[] = {
 };
 
 
-static int pty_unix98_ioctl(struct tty_struct *tty, struct file *file,
+static int pty_unix98_ioctl(struct tty_struct *tty,
 			    unsigned int cmd, unsigned long arg)
 {
 	switch (cmd) {

drivers/tty/rocket.h

@@ -0,0 +1,111 @@
+/*
+ * rocket.h --- the exported interface of the rocket driver to its configuration program.
+ *
+ * Written by Theodore Ts'o, Copyright 1997.
+ * Copyright 1997 Comtrol Corporation. 
+ *
+ */
+
+/*  Model Information Struct */
+typedef struct {
+	unsigned long model;
+	char modelString[80];
+	unsigned long numPorts;
+	int loadrm2;
+	int startingPortNumber;
+} rocketModel_t;
+
+struct rocket_config {
+	int line;
+	int flags;
+	int closing_wait;
+	int close_delay;
+	int port;
+	int reserved[32];
+};
+
+struct rocket_ports {
+	int tty_major;
+	int callout_major;
+	rocketModel_t rocketModel[8];
+};
+
+struct rocket_version {
+	char rocket_version[32];
+	char rocket_date[32];
+	char reserved[64];
+};
+
+/*
+ * Rocketport flags
+ */
+/*#define ROCKET_CALLOUT_NOHUP    0x00000001 */
+#define ROCKET_FORCE_CD		0x00000002
+#define ROCKET_HUP_NOTIFY	0x00000004
+#define ROCKET_SPLIT_TERMIOS	0x00000008
+#define ROCKET_SPD_MASK		0x00000070
+#define ROCKET_SPD_HI		0x00000010	/* Use 56000 instead of 38400 bps */
+#define ROCKET_SPD_VHI		0x00000020	/* Use 115200 instead of 38400 bps */
+#define ROCKET_SPD_SHI		0x00000030	/* Use 230400 instead of 38400 bps */
+#define ROCKET_SPD_WARP	        0x00000040	/* Use 460800 instead of 38400 bps */
+#define ROCKET_SAK		0x00000080
+#define ROCKET_SESSION_LOCKOUT	0x00000100
+#define ROCKET_PGRP_LOCKOUT	0x00000200
+#define ROCKET_RTS_TOGGLE	0x00000400
+#define ROCKET_MODE_MASK        0x00003000
+#define ROCKET_MODE_RS232       0x00000000
+#define ROCKET_MODE_RS485       0x00001000
+#define ROCKET_MODE_RS422       0x00002000
+#define ROCKET_FLAGS		0x00003FFF
+
+#define ROCKET_USR_MASK 0x0071	/* Legal flags that non-privileged
+				 * users can set or reset */
+
+/*
+ * For closing_wait and closing_wait2
+ */
+#define ROCKET_CLOSING_WAIT_NONE	ASYNC_CLOSING_WAIT_NONE
+#define ROCKET_CLOSING_WAIT_INF		ASYNC_CLOSING_WAIT_INF
+
+/*
+ * Rocketport ioctls -- "RP"
+ */
+#define RCKP_GET_STRUCT		0x00525001
+#define RCKP_GET_CONFIG		0x00525002
+#define RCKP_SET_CONFIG		0x00525003
+#define RCKP_GET_PORTS		0x00525004
+#define RCKP_RESET_RM2		0x00525005
+#define RCKP_GET_VERSION	0x00525006
+
+/*  Rocketport Models */
+#define MODEL_RP32INTF        0x0001	/* RP 32 port w/external I/F   */
+#define MODEL_RP8INTF         0x0002	/* RP 8 port w/external I/F    */
+#define MODEL_RP16INTF        0x0003	/* RP 16 port w/external I/F   */
+#define MODEL_RP8OCTA         0x0005	/* RP 8 port w/octa cable      */
+#define MODEL_RP4QUAD         0x0004	/* RP 4 port w/quad cable      */
+#define MODEL_RP8J            0x0006	/* RP 8 port w/RJ11 connectors */
+#define MODEL_RP4J            0x0007	/* RP 4 port w/RJ45 connectors */
+#define MODEL_RP8SNI          0x0008	/* RP 8 port w/ DB78 SNI connector */
+#define MODEL_RP16SNI         0x0009	/* RP 16 port w/ DB78 SNI connector */
+#define MODEL_RPP4            0x000A	/* RP Plus 4 port              */
+#define MODEL_RPP8            0x000B	/* RP Plus 8 port              */
+#define MODEL_RP2_232         0x000E	/* RP Plus 2 port RS232        */
+#define MODEL_RP2_422         0x000F	/* RP Plus 2 port RS232        */
+
+/*  Rocketmodem II Models */
+#define MODEL_RP6M            0x000C	/* RM 6 port                   */
+#define MODEL_RP4M            0x000D	/* RM 4 port                   */
+
+/* Universal PCI boards */
+#define MODEL_UPCI_RP32INTF   0x0801	/* RP UPCI 32 port w/external I/F     */
+#define MODEL_UPCI_RP8INTF    0x0802	/* RP UPCI 8 port w/external I/F      */
+#define MODEL_UPCI_RP16INTF   0x0803	/* RP UPCI 16 port w/external I/F     */
+#define MODEL_UPCI_RP8OCTA    0x0805	/* RP UPCI 8 port w/octa cable        */ 
+#define MODEL_UPCI_RM3_8PORT  0x080C	/* RP UPCI Rocketmodem III 8 port     */
+#define MODEL_UPCI_RM3_4PORT  0x080C	/* RP UPCI Rocketmodem III 4 port     */
+
+/*  Compact PCI 16 port  */
+#define MODEL_CPCI_RP16INTF   0x0903	/* RP Compact PCI 16 port w/external I/F */
+
+/* All ISA boards */
+#define MODEL_ISA             0x1000

drivers/tty/serial/68328serial.c

@@ -262,7 +262,7 @@ static void status_handle(struct m68k_serial *info, unsigned short status)
 
 static void receive_chars(struct m68k_serial *info, unsigned short rx)
 {
-	struct tty_struct *tty = info->port.tty;
+	struct tty_struct *tty = info->tty;
 	m68328_uart *uart = &uart_addr[info->line];
 	unsigned char ch, flag;
 
@@ -329,7 +329,7 @@ static void transmit_chars(struct m68k_serial *info)
 		goto clear_and_return;
 	}
 
-	if((info->xmit_cnt <= 0) || info->port.tty->stopped) {
+	if((info->xmit_cnt <= 0) || info->tty->stopped) {
 		/* That's peculiar... TX ints off */
 		uart->ustcnt &= ~USTCNT_TX_INTR_MASK;
 		goto clear_and_return;
@@ -383,7 +383,7 @@ static void do_softint(struct work_struct *work)
 	struct m68k_serial	*info = container_of(work, struct m68k_serial, tqueue);
 	struct tty_struct	*tty;
 	
-	tty = info->port.tty;
+	tty = info->tty;
 	if (!tty)
 		return;
 #if 0
@@ -393,28 +393,6 @@ static void do_softint(struct work_struct *work)
 #endif   
 }
 
-/*
- * This routine is called from the scheduler tqueue when the interrupt
- * routine has signalled that a hangup has occurred.  The path of
- * hangup processing is:
- *
- * 	serial interrupt routine -> (scheduler tqueue) ->
- * 	do_serial_hangup() -> tty->hangup() -> rs_hangup()
- * 
- */
-static void do_serial_hangup(struct work_struct *work)
-{
-	struct m68k_serial	*info = container_of(work, struct m68k_serial, tqueue_hangup);
-	struct tty_struct	*tty;
-	
-	tty = info->port.tty;
-	if (!tty)
-		return;
-
-	tty_hangup(tty);
-}
-
-
 static int startup(struct m68k_serial * info)
 {
 	m68328_uart *uart = &uart_addr[info->line];
@@ -451,8 +429,8 @@ static int startup(struct m68k_serial * info)
 	uart->ustcnt = USTCNT_UEN | USTCNT_RXEN | USTCNT_RX_INTR_MASK;
 #endif
 
-	if (info->port.tty)
-		clear_bit(TTY_IO_ERROR, &info->port.tty->flags);
+	if (info->tty)
+		clear_bit(TTY_IO_ERROR, &info->tty->flags);
 	info->xmit_cnt = info->xmit_head = info->xmit_tail = 0;
 
 	/*
@@ -486,8 +464,8 @@ static void shutdown(struct m68k_serial * info)
 		info->xmit_buf = 0;
 	}
 
-	if (info->port.tty)
-		set_bit(TTY_IO_ERROR, &info->port.tty->flags);
+	if (info->tty)
+		set_bit(TTY_IO_ERROR, &info->tty->flags);
 	
 	info->flags &= ~S_INITIALIZED;
 	local_irq_restore(flags);
@@ -553,9 +531,9 @@ static void change_speed(struct m68k_serial *info)
 	unsigned cflag;
 	int	i;
 
-	if (!info->port.tty || !info->port.tty->termios)
+	if (!info->tty || !info->tty->termios)
 		return;
-	cflag = info->port.tty->termios->c_cflag;
+	cflag = info->tty->termios->c_cflag;
 	if (!(port = info->port))
 		return;
 
@@ -967,10 +945,9 @@ static void send_break(struct m68k_serial * info, unsigned int duration)
         local_irq_restore(flags);
 }
 
-static int rs_ioctl(struct tty_struct *tty, struct file * file,
+static int rs_ioctl(struct tty_struct *tty,
 		    unsigned int cmd, unsigned long arg)
 {
-	int error;
 	struct m68k_serial * info = (struct m68k_serial *)tty->driver_data;
 	int retval;
 
@@ -1104,7 +1081,7 @@ static void rs_close(struct tty_struct *tty, struct file * filp)
 	tty_ldisc_flush(tty);
 	tty->closing = 0;
 	info->event = 0;
-	info->port.tty = NULL;
+	info->tty = NULL;
 #warning "This is not and has never been valid so fix it"	
 #if 0
 	if (tty->ldisc.num != ldiscs[N_TTY].num) {
@@ -1142,7 +1119,7 @@ void rs_hangup(struct tty_struct *tty)
 	info->event = 0;
 	info->count = 0;
 	info->flags &= ~S_NORMAL_ACTIVE;
-	info->port.tty = NULL;
+	info->tty = NULL;
 	wake_up_interruptible(&info->open_wait);
 }
 
@@ -1261,7 +1238,7 @@ int rs_open(struct tty_struct *tty, struct file * filp)
 
 	info->count++;
 	tty->driver_data = info;
-	info->port.tty = tty;
+	info->tty = tty;
 
 	/*
 	 * Start up serial port
@@ -1338,7 +1315,7 @@ rs68328_init(void)
 	    info = &m68k_soft[i];
 	    info->magic = SERIAL_MAGIC;
 	    info->port = (int) &uart_addr[i];
-	    info->port.tty = NULL;
+	    info->tty = NULL;
 	    info->irq = uart_irqs[i];
 	    info->custom_divisor = 16;
 	    info->close_delay = 50;
@@ -1348,7 +1325,6 @@ rs68328_init(void)
 	    info->count = 0;
 	    info->blocked_open = 0;
 	    INIT_WORK(&info->tqueue, do_softint);
-	    INIT_WORK(&info->tqueue_hangup, do_serial_hangup);
 	    init_waitqueue_head(&info->open_wait);
 	    init_waitqueue_head(&info->close_wait);
 	    info->line = i;

drivers/tty/serial/68328serial.h

@@ -159,7 +159,6 @@ struct m68k_serial {
 	int			xmit_tail;
 	int			xmit_cnt;
 	struct work_struct	tqueue;
-	struct work_struct	tqueue_hangup;
 	wait_queue_head_t	open_wait;
 	wait_queue_head_t	close_wait;
 };

drivers/tty/serial/68360serial.c

@@ -1240,7 +1240,7 @@ static int get_lsr_info(struct async_struct * info, unsigned int *value)
 }
 #endif
 
-static int rs_360_tiocmget(struct tty_struct *tty, struct file *file)
+static int rs_360_tiocmget(struct tty_struct *tty)
 {
 	ser_info_t *info = (ser_info_t *)tty->driver_data;
 	unsigned int result = 0;
@@ -1271,7 +1271,7 @@ static int rs_360_tiocmget(struct tty_struct *tty, struct file *file)
 	return result;
 }
 
-static int rs_360_tiocmset(struct tty_struct *tty, struct file *file,
+static int rs_360_tiocmset(struct tty_struct *tty,
 			   unsigned int set, unsigned int clear)
 {
 #ifdef modem_control
@@ -1405,7 +1405,7 @@ static int rs_360_get_icount(struct tty_struct *tty,
 	return 0;
 }
 
-static int rs_360_ioctl(struct tty_struct *tty, struct file * file,
+static int rs_360_ioctl(struct tty_struct *tty,
 		    unsigned int cmd, unsigned long arg)
 {
 	int error;

drivers/tty/serial/8250.c

@@ -954,6 +954,23 @@ static int broken_efr(struct uart_8250_port *up)
 	return 0;
 }
 
+static inline int ns16550a_goto_highspeed(struct uart_8250_port *up)
+{
+	unsigned char status;
+
+	status = serial_in(up, 0x04); /* EXCR2 */
+#define PRESL(x) ((x) & 0x30)
+	if (PRESL(status) == 0x10) {
+		/* already in high speed mode */
+		return 0;
+	} else {
+		status &= ~0xB0; /* Disable LOCK, mask out PRESL[01] */
+		status |= 0x10;  /* 1.625 divisor for baud_base --> 921600 */
+		serial_outp(up, 0x04, status);
+	}
+	return 1;
+}
+
 /*
  * We know that the chip has FIFOs.  Does it have an EFR?  The
  * EFR is located in the same register position as the IIR and
@@ -1025,12 +1042,8 @@ static void autoconfig_16550a(struct uart_8250_port *up)
 			quot = serial_dl_read(up);
 			quot <<= 3;
 
-			status1 = serial_in(up, 0x04); /* EXCR2 */
-			status1 &= ~0xB0; /* Disable LOCK, mask out PRESL[01] */
-			status1 |= 0x10;  /* 1.625 divisor for baud_base --> 921600 */
-			serial_outp(up, 0x04, status1);
-
-			serial_dl_write(up, quot);
+			if (ns16550a_goto_highspeed(up))
+				serial_dl_write(up, quot);
 
 			serial_outp(up, UART_LCR, 0);
 
@@ -3025,17 +3038,13 @@ void serial8250_resume_port(int line)
 	struct uart_8250_port *up = &serial8250_ports[line];
 
 	if (up->capabilities & UART_NATSEMI) {
-		unsigned char tmp;
-
 		/* Ensure it's still in high speed mode */
 		serial_outp(up, UART_LCR, 0xE0);
 
-		tmp = serial_in(up, 0x04); /* EXCR2 */
-		tmp &= ~0xB0; /* Disable LOCK, mask out PRESL[01] */
-		tmp |= 0x10;  /* 1.625 divisor for baud_base --> 921600 */
-		serial_outp(up, 0x04, tmp);
+		ns16550a_goto_highspeed(up);
 
 		serial_outp(up, UART_LCR, 0);
+		up->port.uartclk = 921600*16;
 	}
 	uart_resume_port(&serial8250_reg, &up->port);
 }

drivers/tty/serial/Kconfig

@@ -1110,29 +1110,6 @@ config SERIAL_PMACZILOG_CONSOLE
 	  on your (Power)Mac as the console, you can do so by answering
 	  Y to this option.
 
-config SERIAL_LH7A40X
-	tristate "Sharp LH7A40X embedded UART support"
-	depends on ARM && ARCH_LH7A40X
-	select SERIAL_CORE
-	help
-	  This enables support for the three on-board UARTs of the
-	  Sharp LH7A40X series CPUs.  Choose Y or M.
-
-config SERIAL_LH7A40X_CONSOLE
-	bool "Support for console on Sharp LH7A40X serial port"
-	depends on SERIAL_LH7A40X=y
-	select SERIAL_CORE_CONSOLE
-	help
-	  Say Y here if you wish to use one of the serial ports as the
-	  system console--the system console is the device which
-	  receives all kernel messages and warnings and which allows
-	  logins in single user mode.
-
-	  Even if you say Y here, the currently visible framebuffer console
-	  (/dev/tty0) will still be used as the default system console, but
-	  you can alter that using a kernel command line, for example
-	  "console=ttyAM1".
-
 config SERIAL_CPM
 	tristate "CPM SCC/SMC serial port support"
 	depends on CPM2 || 8xx
@@ -1319,6 +1296,18 @@ config SERIAL_MSM_CONSOLE
 	depends on SERIAL_MSM=y
 	select SERIAL_CORE_CONSOLE
 
+config SERIAL_MSM_HS
+	tristate "MSM UART High Speed: Serial Driver"
+	depends on ARCH_MSM
+	select SERIAL_CORE
+	help
+	  If you have a machine based on MSM family of SoCs, you
+	  can enable its onboard high speed serial port by enabling
+	  this option.
+
+	  Choose M here to compile it as a module. The module will be
+	  called msm_serial_hs.
+
 config SERIAL_VT8500
 	bool "VIA VT8500 on-chip serial port support"
 	depends on ARM && ARCH_VT8500
@@ -1588,12 +1577,25 @@ config SERIAL_IFX6X60
 	  Support for the IFX6x60 modem devices on Intel MID platforms.
 
 config SERIAL_PCH_UART
-	tristate "Intel EG20T PCH UART"
-	depends on PCI && DMADEVICES
+	tristate "Intel EG20T PCH UART/OKI SEMICONDUCTOR ML7213 IOH"
+	depends on PCI
 	select SERIAL_CORE
-	select PCH_DMA
 	help
 	  This driver is for PCH(Platform controller Hub) UART of Intel EG20T
 	  which is an IOH(Input/Output Hub) for x86 embedded processor.
 	  Enabling PCH_DMA, this PCH UART works as DMA mode.
+
+	  This driver also can be used for OKI SEMICONDUCTOR ML7213 IOH(Input/
+	  Output Hub) which is for IVI(In-Vehicle Infotainment) use.
+	  ML7213 is companion chip for Intel Atom E6xx series.
+	  ML7213 is completely compatible for Intel EG20T PCH.
+
+config SERIAL_MSM_SMD
+	bool "Enable tty device interface for some SMD ports"
+	default n
+	depends on MSM_SMD
+	help
+	  Enables userspace clients to read and write to some streaming SMD
+	  ports via tty device interface for MSM chipset.
+
 endmenu

drivers/tty/serial/Makefile

@@ -54,7 +54,6 @@ obj-$(CONFIG_SERIAL_68328) += 68328serial.o
 obj-$(CONFIG_SERIAL_68360) += 68360serial.o
 obj-$(CONFIG_SERIAL_MCF) += mcf.o
 obj-$(CONFIG_SERIAL_PMACZILOG) += pmac_zilog.o
-obj-$(CONFIG_SERIAL_LH7A40X) += serial_lh7a40x.o
 obj-$(CONFIG_SERIAL_DZ) += dz.o
 obj-$(CONFIG_SERIAL_ZS) += zs.o
 obj-$(CONFIG_SERIAL_SH_SCI) += sh-sci.o
@@ -76,6 +75,7 @@ obj-$(CONFIG_SERIAL_SGI_IOC3) += ioc3_serial.o
 obj-$(CONFIG_SERIAL_ATMEL) += atmel_serial.o
 obj-$(CONFIG_SERIAL_UARTLITE) += uartlite.o
 obj-$(CONFIG_SERIAL_MSM) += msm_serial.o
+obj-$(CONFIG_SERIAL_MSM_HS) += msm_serial_hs.o
 obj-$(CONFIG_SERIAL_NETX) += netx-serial.o
 obj-$(CONFIG_SERIAL_OF_PLATFORM) += of_serial.o
 obj-$(CONFIG_SERIAL_OF_PLATFORM_NWPSERIAL) += nwpserial.o
@@ -92,3 +92,4 @@ obj-$(CONFIG_SERIAL_MRST_MAX3110)	+= mrst_max3110.o
 obj-$(CONFIG_SERIAL_MFD_HSU)	+= mfd.o
 obj-$(CONFIG_SERIAL_IFX6X60)  	+= ifx6x60.o
 obj-$(CONFIG_SERIAL_PCH_UART)	+= pch_uart.o
+obj-$(CONFIG_SERIAL_MSM_SMD)	+= msm_smd_tty.o

drivers/tty/serial/altera_jtaguart.c

@@ -305,28 +305,6 @@ static struct altera_jtaguart altera_jtaguart_ports[ALTERA_JTAGUART_MAXPORTS];
 
 #if defined(CONFIG_SERIAL_ALTERA_JTAGUART_CONSOLE)
 
-int __init early_altera_jtaguart_setup(struct altera_jtaguart_platform_uart
-				       *platp)
-{
-	struct uart_port *port;
-	int i;
-
-	for (i = 0; i < ALTERA_JTAGUART_MAXPORTS && platp[i].mapbase; i++) {
-		port = &altera_jtaguart_ports[i].port;
-
-		port->line = i;
-		port->type = PORT_ALTERA_JTAGUART;
-		port->mapbase = platp[i].mapbase;
-		port->membase = ioremap(port->mapbase, ALTERA_JTAGUART_SIZE);
-		port->iotype = SERIAL_IO_MEM;
-		port->irq = platp[i].irq;
-		port->flags = ASYNC_BOOT_AUTOCONF;
-		port->ops = &altera_jtaguart_ops;
-	}
-
-	return 0;
-}
-
 #if defined(CONFIG_SERIAL_ALTERA_JTAGUART_CONSOLE_BYPASS)
 static void altera_jtaguart_console_putc(struct console *co, const char c)
 {
@@ -384,7 +362,7 @@ static int __init altera_jtaguart_console_setup(struct console *co,
 	if (co->index < 0 || co->index >= ALTERA_JTAGUART_MAXPORTS)
 		return -EINVAL;
 	port = &altera_jtaguart_ports[co->index].port;
-	if (port->membase == 0)
+	if (port->membase == NULL)
 		return -ENODEV;
 	return 0;
 }
@@ -431,22 +409,45 @@ static int __devinit altera_jtaguart_probe(struct platform_device *pdev)
 {
 	struct altera_jtaguart_platform_uart *platp = pdev->dev.platform_data;
 	struct uart_port *port;
-	int i;
+	struct resource *res_irq, *res_mem;
+	int i = pdev->id;
 
-	for (i = 0; i < ALTERA_JTAGUART_MAXPORTS && platp[i].mapbase; i++) {
-		port = &altera_jtaguart_ports[i].port;
+	/* -1 emphasizes that the platform must have one port, no .N suffix */
+	if (i == -1)
+		i = 0;
 
-		port->line = i;
-		port->type = PORT_ALTERA_JTAGUART;
-		port->mapbase = platp[i].mapbase;
-		port->membase = ioremap(port->mapbase, ALTERA_JTAGUART_SIZE);
-		port->iotype = SERIAL_IO_MEM;
-		port->irq = platp[i].irq;
-		port->ops = &altera_jtaguart_ops;
-		port->flags = ASYNC_BOOT_AUTOCONF;
+	if (i >= ALTERA_JTAGUART_MAXPORTS)
+		return -EINVAL;
 
-		uart_add_one_port(&altera_jtaguart_driver, port);
-	}
+	port = &altera_jtaguart_ports[i].port;
+
+	res_mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (res_mem)
+		port->mapbase = res_mem->start;
+	else if (platp)
+		port->mapbase = platp->mapbase;
+	else
+		return -ENODEV;
+
+	res_irq = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
+	if (res_irq)
+		port->irq = res_irq->start;
+	else if (platp)
+		port->irq = platp->irq;
+	else
+		return -ENODEV;
+
+	port->membase = ioremap(port->mapbase, ALTERA_JTAGUART_SIZE);
+	if (!port->membase)
+		return -ENOMEM;
+
+	port->line = i;
+	port->type = PORT_ALTERA_JTAGUART;
+	port->iotype = SERIAL_IO_MEM;
+	port->ops = &altera_jtaguart_ops;
+	port->flags = UPF_BOOT_AUTOCONF;
+
+	uart_add_one_port(&altera_jtaguart_driver, port);
 
 	return 0;
 }
@@ -454,23 +455,34 @@ static int __devinit altera_jtaguart_probe(struct platform_device *pdev)
 static int __devexit altera_jtaguart_remove(struct platform_device *pdev)
 {
 	struct uart_port *port;
-	int i;
+	int i = pdev->id;
 
-	for (i = 0; i < ALTERA_JTAGUART_MAXPORTS; i++) {
-		port = &altera_jtaguart_ports[i].port;
-		if (port)
-			uart_remove_one_port(&altera_jtaguart_driver, port);
-	}
+	if (i == -1)
+		i = 0;
+
+	port = &altera_jtaguart_ports[i].port;
+	uart_remove_one_port(&altera_jtaguart_driver, port);
 
 	return 0;
 }
 
+#ifdef CONFIG_OF
+static struct of_device_id altera_jtaguart_match[] = {
+	{ .compatible = "ALTR,juart-1.0", },
+	{},
+};
+MODULE_DEVICE_TABLE(of, altera_jtaguart_match);
+#else
+#define altera_jtaguart_match NULL
+#endif /* CONFIG_OF */
+
 static struct platform_driver altera_jtaguart_platform_driver = {
 	.probe	= altera_jtaguart_probe,
 	.remove	= __devexit_p(altera_jtaguart_remove),
 	.driver	= {
-		.name	= DRV_NAME,
-		.owner	= THIS_MODULE,
+		.name		= DRV_NAME,
+		.owner		= THIS_MODULE,
+		.of_match_table	= altera_jtaguart_match,
 	},
 };
 

drivers/tty/serial/altera_uart.c

@@ -24,6 +24,7 @@
 #include <linux/serial.h>
 #include <linux/serial_core.h>
 #include <linux/platform_device.h>
+#include <linux/of.h>
 #include <linux/io.h>
 #include <linux/altera_uart.h>
 
@@ -86,16 +87,12 @@ struct altera_uart {
 
 static u32 altera_uart_readl(struct uart_port *port, int reg)
 {
-	struct altera_uart_platform_uart *platp = port->private_data;
-
-	return readl(port->membase + (reg << platp->bus_shift));
+	return readl(port->membase + (reg << port->regshift));
 }
 
 static void altera_uart_writel(struct uart_port *port, u32 dat, int reg)
 {
-	struct altera_uart_platform_uart *platp = port->private_data;
-
-	writel(dat, port->membase + (reg << platp->bus_shift));
+	writel(dat, port->membase + (reg << port->regshift));
 }
 
 static unsigned int altera_uart_tx_empty(struct uart_port *port)
@@ -511,6 +508,29 @@ static struct uart_driver altera_uart_driver = {
 	.cons		= ALTERA_UART_CONSOLE,
 };
 
+#ifdef CONFIG_OF
+static int altera_uart_get_of_uartclk(struct platform_device *pdev,
+				      struct uart_port *port)
+{
+	int len;
+	const __be32 *clk;
+
+	clk = of_get_property(pdev->dev.of_node, "clock-frequency", &len);
+	if (!clk || len < sizeof(__be32))
+		return -ENODEV;
+
+	port->uartclk = be32_to_cpup(clk);
+
+	return 0;
+}
+#else
+static int altera_uart_get_of_uartclk(struct platform_device *pdev,
+				      struct uart_port *port)
+{
+	return -ENODEV;
+}
+#endif /* CONFIG_OF */
+
 static int __devinit altera_uart_probe(struct platform_device *pdev)
 {
 	struct altera_uart_platform_uart *platp = pdev->dev.platform_data;
@@ -518,6 +538,7 @@ static int __devinit altera_uart_probe(struct platform_device *pdev)
 	struct resource *res_mem;
 	struct resource *res_irq;
 	int i = pdev->id;
+	int ret;
 
 	/* -1 emphasizes that the platform must have one port, no .N suffix */
 	if (i == -1)
@@ -542,17 +563,29 @@ static int __devinit altera_uart_probe(struct platform_device *pdev)
 	else if (platp->irq)
 		port->irq = platp->irq;
 
+	/* Check platform data first so we can override device node data */
+	if (platp)
+		port->uartclk = platp->uartclk;
+	else {
+		ret = altera_uart_get_of_uartclk(pdev, port);
+		if (ret)
+			return ret;
+	}
+
 	port->membase = ioremap(port->mapbase, ALTERA_UART_SIZE);
 	if (!port->membase)
 		return -ENOMEM;
 
+	if (platp)
+		port->regshift = platp->bus_shift;
+	else
+		port->regshift = 0;
+
 	port->line = i;
 	port->type = PORT_ALTERA_UART;
 	port->iotype = SERIAL_IO_MEM;
-	port->uartclk = platp->uartclk;
 	port->ops = &altera_uart_ops;
 	port->flags = UPF_BOOT_AUTOCONF;
-	port->private_data = platp;
 
 	uart_add_one_port(&altera_uart_driver, port);
 
@@ -561,19 +594,35 @@ static int __devinit altera_uart_probe(struct platform_device *pdev)
 
 static int __devexit altera_uart_remove(struct platform_device *pdev)
 {
-	struct uart_port *port = &altera_uart_ports[pdev->id].port;
+	struct uart_port *port;
+	int i = pdev->id;
 
+	if (i == -1)
+		i = 0;
+
+	port = &altera_uart_ports[i].port;
 	uart_remove_one_port(&altera_uart_driver, port);
+
 	return 0;
 }
 
+#ifdef CONFIG_OF
+static struct of_device_id altera_uart_match[] = {
+	{ .compatible = "ALTR,uart-1.0", },
+	{},
+};
+MODULE_DEVICE_TABLE(of, altera_uart_match);
+#else
+#define altera_uart_match NULL
+#endif /* CONFIG_OF */
+
 static struct platform_driver altera_uart_platform_driver = {
 	.probe	= altera_uart_probe,
 	.remove	= __devexit_p(altera_uart_remove),
 	.driver	= {
-		.name	= DRV_NAME,
-		.owner	= THIS_MODULE,
-		.pm	= NULL,
+		.name		= DRV_NAME,
+		.owner		= THIS_MODULE,
+		.of_match_table	= altera_uart_match,
 	},
 };
 

drivers/tty/serial/apbuart.c

@@ -553,8 +553,7 @@ static struct uart_driver grlib_apbuart_driver = {
 /* OF Platform Driver                                                       */
 /* ======================================================================== */
 
-static int __devinit apbuart_probe(struct platform_device *op,
-				   const struct of_device_id *match)
+static int __devinit apbuart_probe(struct platform_device *op)
 {
 	int i = -1;
 	struct uart_port *port = NULL;
@@ -587,7 +586,7 @@ static struct of_device_id __initdata apbuart_match[] = {
 	{},
 };
 
-static struct of_platform_driver grlib_apbuart_of_driver = {
+static struct platform_driver grlib_apbuart_of_driver = {
 	.probe = apbuart_probe,
 	.driver = {
 		.owner = THIS_MODULE,
@@ -676,10 +675,10 @@ static int __init grlib_apbuart_init(void)
 		return ret;
 	}
 
-	ret = of_register_platform_driver(&grlib_apbuart_of_driver);
+	ret = platform_driver_register(&grlib_apbuart_of_driver);
 	if (ret) {
 		printk(KERN_ERR
-		       "%s: of_register_platform_driver failed (%i)\n",
+		       "%s: platform_driver_register failed (%i)\n",
 		       __FILE__, ret);
 		uart_unregister_driver(&grlib_apbuart_driver);
 		return ret;
@@ -697,7 +696,7 @@ static void __exit grlib_apbuart_exit(void)
 				     &grlib_apbuart_ports[i]);
 
 	uart_unregister_driver(&grlib_apbuart_driver);
-	of_unregister_platform_driver(&grlib_apbuart_of_driver);
+	platform_driver_unregister(&grlib_apbuart_of_driver);
 }
 
 module_init(grlib_apbuart_init);

drivers/tty/serial/atmel_serial.c

@@ -1240,6 +1240,21 @@ static void atmel_set_termios(struct uart_port *port, struct ktermios *termios,
 	spin_unlock_irqrestore(&port->lock, flags);
 }
 
+static void atmel_set_ldisc(struct uart_port *port, int new)
+{
+	int line = port->line;
+
+	if (line >= port->state->port.tty->driver->num)
+		return;
+
+	if (port->state->port.tty->ldisc->ops->num == N_PPS) {
+		port->flags |= UPF_HARDPPS_CD;
+		atmel_enable_ms(port);
+	} else {
+		port->flags &= ~UPF_HARDPPS_CD;
+	}
+}
+
 /*
  * Return string describing the specified port
  */
@@ -1380,6 +1395,7 @@ static struct uart_ops atmel_pops = {
 	.shutdown	= atmel_shutdown,
 	.flush_buffer	= atmel_flush_buffer,
 	.set_termios	= atmel_set_termios,
+	.set_ldisc	= atmel_set_ldisc,
 	.type		= atmel_type,
 	.release_port	= atmel_release_port,
 	.request_port	= atmel_request_port,

drivers/tty/serial/bfin_sport_uart.c

@@ -788,7 +788,7 @@ static int __devinit sport_uart_probe(struct platform_device *pdev)
 		sport->port.mapbase = res->start;
 
 		sport->port.irq = platform_get_irq(pdev, 0);
-		if (sport->port.irq < 0) {
+		if ((int)sport->port.irq < 0) {
 			dev_err(&pdev->dev, "No sport RX/TX IRQ specified\n");
 			ret = -ENOENT;
 			goto out_error_unmap;

drivers/tty/serial/cpm_uart/cpm_uart_core.c

@@ -1359,8 +1359,7 @@ static struct uart_driver cpm_reg = {
 
 static int probe_index;
 
-static int __devinit cpm_uart_probe(struct platform_device *ofdev,
-                                    const struct of_device_id *match)
+static int __devinit cpm_uart_probe(struct platform_device *ofdev)
 {
 	int index = probe_index++;
 	struct uart_cpm_port *pinfo = &cpm_uart_ports[index];
@@ -1405,7 +1404,7 @@ static struct of_device_id cpm_uart_match[] = {
 	{}
 };
 
-static struct of_platform_driver cpm_uart_driver = {
+static struct platform_driver cpm_uart_driver = {
 	.driver = {
 		.name = "cpm_uart",
 		.owner = THIS_MODULE,
@@ -1421,7 +1420,7 @@ static int __init cpm_uart_init(void)
 	if (ret)
 		return ret;
 
-	ret = of_register_platform_driver(&cpm_uart_driver);
+	ret = platform_driver_register(&cpm_uart_driver);
 	if (ret)
 		uart_unregister_driver(&cpm_reg);
 
@@ -1430,7 +1429,7 @@ static int __init cpm_uart_init(void)
 
 static void __exit cpm_uart_exit(void)
 {
-	of_unregister_platform_driver(&cpm_uart_driver);
+	platform_driver_unregister(&cpm_uart_driver);
 	uart_unregister_driver(&cpm_reg);
 }
 

drivers/tty/serial/crisv10.c

@@ -3581,8 +3581,7 @@ rs_break(struct tty_struct *tty, int break_state)
 }
 
 static int
-rs_tiocmset(struct tty_struct *tty, struct file *file,
-		unsigned int set, unsigned int clear)
+rs_tiocmset(struct tty_struct *tty, unsigned int set, unsigned int clear)
 {
 	struct e100_serial *info = (struct e100_serial *)tty->driver_data;
 	unsigned long flags;
@@ -3614,7 +3613,7 @@ rs_tiocmset(struct tty_struct *tty, struct file *file,
 }
 
 static int
-rs_tiocmget(struct tty_struct *tty, struct file *file)
+rs_tiocmget(struct tty_struct *tty)
 {
 	struct e100_serial *info = (struct e100_serial *)tty->driver_data;
 	unsigned int result;
@@ -3648,7 +3647,7 @@ rs_tiocmget(struct tty_struct *tty, struct file *file)
 
 
 static int
-rs_ioctl(struct tty_struct *tty, struct file * file,
+rs_ioctl(struct tty_struct *tty,
 	 unsigned int cmd, unsigned long arg)
 {
 	struct e100_serial * info = (struct e100_serial *)tty->driver_data;

drivers/tty/serial/ifx6x60.c

@@ -8,7 +8,7 @@
  *		      Jan Dumon <j.dumon@option.com>
  *
  * Copyright (C) 2009, 2010 Intel Corp
- * Russ Gorby <richardx.r.gorby@intel.com>
+ * Russ Gorby <russ.gorby@intel.com>
  *
  * This program is free software; you can redistribute it and/or modify
  * it under the terms of the GNU General Public License version 2 as
@@ -67,6 +67,7 @@
 #define IFX_SPI_MORE_MASK		0x10
 #define IFX_SPI_MORE_BIT		12	/* bit position in u16 */
 #define IFX_SPI_CTS_BIT			13	/* bit position in u16 */
+#define IFX_SPI_MODE			SPI_MODE_1
 #define IFX_SPI_TTY_ID			0
 #define IFX_SPI_TIMEOUT_SEC		2
 #define IFX_SPI_HEADER_0		(-1)
@@ -76,7 +77,7 @@
 static void ifx_spi_handle_srdy(struct ifx_spi_device *ifx_dev);
 
 /* local variables */
-static int spi_b16 = 1;			/* 8 or 16 bit word length */
+static int spi_bpw = 16;		/* 8, 16 or 32 bit word length */
 static struct tty_driver *tty_drv;
 static struct ifx_spi_device *saved_ifx_dev;
 static struct lock_class_key ifx_spi_key;
@@ -244,7 +245,7 @@ static void ifx_spi_timeout(unsigned long arg)
  *	Map the signal state into Linux modem flags and report the value
  *	in Linux terms
  */
-static int ifx_spi_tiocmget(struct tty_struct *tty, struct file *filp)
+static int ifx_spi_tiocmget(struct tty_struct *tty)
 {
 	unsigned int value;
 	struct ifx_spi_device *ifx_dev = tty->driver_data;
@@ -262,7 +263,6 @@ static int ifx_spi_tiocmget(struct tty_struct *tty, struct file *filp)
 /**
  *	ifx_spi_tiocmset	-	set modem bits
  *	@tty: the tty structure
- *	@filp: file handle issuing the request
  *	@set: bits to set
  *	@clear: bits to clear
  *
@@ -271,7 +271,7 @@ static int ifx_spi_tiocmget(struct tty_struct *tty, struct file *filp)
  *
  *	FIXME: do we need to kick the tranfers when we do this ?
  */
-static int ifx_spi_tiocmset(struct tty_struct *tty, struct file *filp,
+static int ifx_spi_tiocmset(struct tty_struct *tty,
 			    unsigned int set, unsigned int clear)
 {
 	struct ifx_spi_device *ifx_dev = tty->driver_data;
@@ -722,9 +722,9 @@ static void ifx_spi_io(unsigned long data)
 		/* note len is BYTES, not transfers */
 		ifx_dev->spi_xfer.len = IFX_SPI_TRANSFER_SIZE;
 		ifx_dev->spi_xfer.cs_change = 0;
-		ifx_dev->spi_xfer.speed_hz = 12500000;
+		ifx_dev->spi_xfer.speed_hz = ifx_dev->spi_dev->max_speed_hz;
 		/* ifx_dev->spi_xfer.speed_hz = 390625; */
-		ifx_dev->spi_xfer.bits_per_word = spi_b16 ? 16 : 8;
+		ifx_dev->spi_xfer.bits_per_word = spi_bpw;
 
 		ifx_dev->spi_xfer.tx_buf = ifx_dev->tx_buffer;
 		ifx_dev->spi_xfer.rx_buf = ifx_dev->rx_buffer;
@@ -732,7 +732,7 @@ static void ifx_spi_io(unsigned long data)
 		/*
 		 * setup dma pointers
 		 */
-		if (ifx_dev->is_6160) {
+		if (ifx_dev->use_dma) {
 			ifx_dev->spi_msg.is_dma_mapped = 1;
 			ifx_dev->tx_dma = ifx_dev->tx_bus;
 			ifx_dev->rx_dma = ifx_dev->rx_bus;
@@ -798,8 +798,8 @@ static int ifx_spi_create_port(struct ifx_spi_device *ifx_dev)
 		goto error_ret;
 	}
 
-	pport->ops = &ifx_tty_port_ops;
 	tty_port_init(pport);
+	pport->ops = &ifx_tty_port_ops;
 	ifx_dev->minor = IFX_SPI_TTY_ID;
 	ifx_dev->tty_dev = tty_register_device(tty_drv, ifx_dev->minor,
 					       &ifx_dev->spi_dev->dev);
@@ -960,7 +960,7 @@ static int ifx_spi_spi_probe(struct spi_device *spi)
 {
 	int ret;
 	int srdy;
-	struct ifx_modem_platform_data *pl_data = NULL;
+	struct ifx_modem_platform_data *pl_data;
 	struct ifx_spi_device *ifx_dev;
 
 	if (saved_ifx_dev) {
@@ -968,6 +968,12 @@ static int ifx_spi_spi_probe(struct spi_device *spi)
 		return -ENODEV;
 	}
 
+	pl_data = (struct ifx_modem_platform_data *)spi->dev.platform_data;
+	if (!pl_data) {
+		dev_err(&spi->dev, "missing platform data!");
+		return -ENODEV;
+	}
+
 	/* initialize structure to hold our device variables */
 	ifx_dev = kzalloc(sizeof(struct ifx_spi_device), GFP_KERNEL);
 	if (!ifx_dev) {
@@ -983,14 +989,25 @@ static int ifx_spi_spi_probe(struct spi_device *spi)
 	init_timer(&ifx_dev->spi_timer);
 	ifx_dev->spi_timer.function = ifx_spi_timeout;
 	ifx_dev->spi_timer.data = (unsigned long)ifx_dev;
-	ifx_dev->is_6160 = pl_data->is_6160;
+	ifx_dev->modem = pl_data->modem_type;
+	ifx_dev->use_dma = pl_data->use_dma;
+	ifx_dev->max_hz = pl_data->max_hz;
+	/* initialize spi mode, etc */
+	spi->max_speed_hz = ifx_dev->max_hz;
+	spi->mode = IFX_SPI_MODE | (SPI_LOOP & spi->mode);
+	spi->bits_per_word = spi_bpw;
+	ret = spi_setup(spi);
+	if (ret) {
+		dev_err(&spi->dev, "SPI setup wasn't successful %d", ret);
+		return -ENODEV;
+	}
 
 	/* ensure SPI protocol flags are initialized to enable transfer */
 	ifx_dev->spi_more = 0;
 	ifx_dev->spi_slave_cts = 0;
 
 	/*initialize transfer and dma buffers */
-	ifx_dev->tx_buffer = dma_alloc_coherent(&ifx_dev->spi_dev->dev,
+	ifx_dev->tx_buffer = dma_alloc_coherent(ifx_dev->spi_dev->dev.parent,
 				IFX_SPI_TRANSFER_SIZE,
 				&ifx_dev->tx_bus,
 				GFP_KERNEL);
@@ -999,7 +1016,7 @@ static int ifx_spi_spi_probe(struct spi_device *spi)
 		ret = -ENOMEM;
 		goto error_ret;
 	}
-	ifx_dev->rx_buffer = dma_alloc_coherent(&ifx_dev->spi_dev->dev,
+	ifx_dev->rx_buffer = dma_alloc_coherent(ifx_dev->spi_dev->dev.parent,
 				IFX_SPI_TRANSFER_SIZE,
 				&ifx_dev->rx_bus,
 				GFP_KERNEL);
@@ -1025,18 +1042,11 @@ static int ifx_spi_spi_probe(struct spi_device *spi)
 		goto error_ret;
 	}
 
-	pl_data = (struct ifx_modem_platform_data *)spi->dev.platform_data;
-	if (pl_data) {
-		ifx_dev->gpio.reset = pl_data->rst_pmu;
-		ifx_dev->gpio.po = pl_data->pwr_on;
-		ifx_dev->gpio.mrdy = pl_data->mrdy;
-		ifx_dev->gpio.srdy = pl_data->srdy;
-		ifx_dev->gpio.reset_out = pl_data->rst_out;
-	} else {
-		dev_err(&spi->dev, "missing platform data!");
-		ret = -ENODEV;
-		goto error_ret;
-	}
+	ifx_dev->gpio.reset = pl_data->rst_pmu;
+	ifx_dev->gpio.po = pl_data->pwr_on;
+	ifx_dev->gpio.mrdy = pl_data->mrdy;
+	ifx_dev->gpio.srdy = pl_data->srdy;
+	ifx_dev->gpio.reset_out = pl_data->rst_out;
 
 	dev_info(&spi->dev, "gpios %d, %d, %d, %d, %d",
 		 ifx_dev->gpio.reset, ifx_dev->gpio.po, ifx_dev->gpio.mrdy,
@@ -1322,9 +1332,9 @@ static const struct spi_device_id ifx_id_table[] = {
 MODULE_DEVICE_TABLE(spi, ifx_id_table);
 
 /* spi operations */
-static const struct spi_driver ifx_spi_driver_6160 = {
+static const struct spi_driver ifx_spi_driver = {
 	.driver = {
-		.name = "ifx6160",
+		.name = DRVNAME,
 		.bus = &spi_bus_type,
 		.pm = &ifx_spi_pm,
 		.owner = THIS_MODULE},
@@ -1346,7 +1356,7 @@ static void __exit ifx_spi_exit(void)
 {
 	/* unregister */
 	tty_unregister_driver(tty_drv);
-	spi_unregister_driver((void *)&ifx_spi_driver_6160);
+	spi_unregister_driver((void *)&ifx_spi_driver);
 }
 
 /**
@@ -1388,7 +1398,7 @@ static int __init ifx_spi_init(void)
 		return result;
 	}
 
-	result = spi_register_driver((void *)&ifx_spi_driver_6160);
+	result = spi_register_driver((void *)&ifx_spi_driver);
 	if (result) {
 		pr_err("%s: spi_register_driver failed(%d)",
 			DRVNAME, result);

drivers/tty/serial/ifx6x60.h

@@ -29,8 +29,6 @@
 #define DRVNAME				"ifx6x60"
 #define TTYNAME				"ttyIFX"
 
-/* #define IFX_THROTTLE_CODE */
-
 #define IFX_SPI_MAX_MINORS		1
 #define IFX_SPI_TRANSFER_SIZE		2048
 #define IFX_SPI_FIFO_SIZE		4096
@@ -88,7 +86,9 @@ struct ifx_spi_device {
 	dma_addr_t rx_dma;
 	dma_addr_t tx_dma;
 
-	int is_6160;				/* Modem type */
+	int modem;		/* Modem type */
+	int use_dma;		/* provide dma-able addrs in SPI msg */
+	long max_hz;		/* max SPI frequency */
 
 	spinlock_t write_lock;
 	int write_pending;

drivers/tty/serial/max3100.c

@@ -601,7 +601,7 @@ static int max3100_startup(struct uart_port *port)
 	s->rts = 0;
 
 	sprintf(b, "max3100-%d", s->minor);
-	s->workqueue = create_freezeable_workqueue(b);
+	s->workqueue = create_freezable_workqueue(b);
 	if (!s->workqueue) {
 		dev_warn(&s->spi->dev, "cannot create workqueue\n");
 		return -EBUSY;

drivers/tty/serial/max3107.c

@@ -833,7 +833,7 @@ static int max3107_startup(struct uart_port *port)
 	struct max3107_port *s = container_of(port, struct max3107_port, port);
 
 	/* Initialize work queue */
-	s->workqueue = create_freezeable_workqueue("max3107");
+	s->workqueue = create_freezable_workqueue("max3107");
 	if (!s->workqueue) {
 		dev_err(&s->spi->dev, "Workqueue creation failed\n");
 		return -EBUSY;

drivers/tty/serial/mfd.c

@@ -16,9 +16,7 @@
  *    2/3 chan to port 1, 4/5 chan to port 3. Even number chans
  *    are used for RX, odd chans for TX
  *
- * 2. In A0 stepping, UART will not support TX half empty flag
- *
- * 3. The RI/DSR/DCD/DTR are not pinned out, DCD & DSR are always
+ * 2. The RI/DSR/DCD/DTR are not pinned out, DCD & DSR are always
  *    asserted, only when the HW is reset the DDCD and DDSR will
  *    be triggered
  */
@@ -41,8 +39,6 @@
 #include <linux/io.h>
 #include <linux/debugfs.h>
 
-#define  MFD_HSU_A0_STEPPING	1
-
 #define HSU_DMA_BUF_SIZE	2048
 
 #define chan_readl(chan, offset)	readl(chan->reg + offset)
@@ -51,7 +47,10 @@
 #define mfd_readl(obj, offset)		readl(obj->reg + offset)
 #define mfd_writel(obj, offset, val)	writel(val, obj->reg + offset)
 
-#define HSU_DMA_TIMEOUT_CHECK_FREQ	(HZ/10)
+static int hsu_dma_enable;
+module_param(hsu_dma_enable, int, 0);
+MODULE_PARM_DESC(hsu_dma_enable, "It is a bitmap to set working mode, if \
+bit[x] is 1, then port[x] will work in DMA mode, otherwise in PIO mode.");
 
 struct hsu_dma_buffer {
 	u8		*buf;
@@ -65,7 +64,6 @@ struct hsu_dma_chan {
 	enum dma_data_direction	dirt;
 	struct uart_hsu_port	*uport;
 	void __iomem		*reg;
-	struct timer_list	rx_timer; /* only needed by RX channel */
 };
 
 struct uart_hsu_port {
@@ -355,8 +353,6 @@ void hsu_dma_start_rx_chan(struct hsu_dma_chan *rxc, struct hsu_dma_buffer *dbuf
 					 | (0x1 << 24)	/* timeout bit, see HSU Errata 1 */
 					 );
 	chan_writel(rxc, HSU_CH_CR, 0x3);
-
-	mod_timer(&rxc->rx_timer, jiffies + HSU_DMA_TIMEOUT_CHECK_FREQ);
 }
 
 /* Protected by spin_lock_irqsave(port->lock) */
@@ -420,7 +416,6 @@ void hsu_dma_rx(struct uart_hsu_port *up, u32 int_sts)
 		chan_writel(chan, HSU_CH_CR, 0x3);
 		return;
 	}
-	del_timer(&chan->rx_timer);
 
 	dma_sync_single_for_cpu(port->dev, dbuf->dma_addr,
 			dbuf->dma_size, DMA_FROM_DEVICE);
@@ -448,8 +443,6 @@ void hsu_dma_rx(struct uart_hsu_port *up, u32 int_sts)
 	tty_flip_buffer_push(tty);
 
 	chan_writel(chan, HSU_CH_CR, 0x3);
-	chan->rx_timer.expires = jiffies + HSU_DMA_TIMEOUT_CHECK_FREQ;
-	add_timer(&chan->rx_timer);
 
 }
 
@@ -551,16 +544,9 @@ static void transmit_chars(struct uart_hsu_port *up)
 		return;
 	}
 
-#ifndef MFD_HSU_A0_STEPPING
+	/* The IRQ is for TX FIFO half-empty */
 	count = up->port.fifosize / 2;
-#else
-	/*
-	 * A0 only supports fully empty IRQ, and the first char written
-	 * into it won't clear the EMPT bit, so we may need be cautious
-	 * by useing a shorter buffer
-	 */
-	count = up->port.fifosize - 4;
-#endif
+
 	do {
 		serial_out(up, UART_TX, xmit->buf[xmit->tail]);
 		xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
@@ -769,9 +755,8 @@ static void serial_hsu_break_ctl(struct uart_port *port, int break_state)
 /*
  * What special to do:
  * 1. chose the 64B fifo mode
- * 2. make sure not to select half empty mode for A0 stepping
- * 3. start dma or pio depends on configuration
- * 4. we only allocate dma memory when needed
+ * 2. start dma or pio depends on configuration
+ * 3. we only allocate dma memory when needed
  */
 static int serial_hsu_startup(struct uart_port *port)
 {
@@ -870,8 +855,6 @@ static void serial_hsu_shutdown(struct uart_port *port)
 		container_of(port, struct uart_hsu_port, port);
 	unsigned long flags;
 
-	del_timer_sync(&up->rxc->rx_timer);
-
 	/* Disable interrupts from this port */
 	up->ier = 0;
 	serial_out(up, UART_IER, 0);
@@ -977,10 +960,6 @@ serial_hsu_set_termios(struct uart_port *port, struct ktermios *termios,
 		fcr = UART_FCR_ENABLE_FIFO | UART_FCR_HSU_64_32B;
 
 	fcr |= UART_FCR_HSU_64B_FIFO;
-#ifdef MFD_HSU_A0_STEPPING
-	/* A0 doesn't support half empty IRQ */
-	fcr |= UART_FCR_FULL_EMPT_TXI;
-#endif
 
 	/*
 	 * Ok, we're now changing the port state.  Do it with
@@ -1343,28 +1322,6 @@ err_disable:
 	return ret;
 }
 
-static void hsu_dma_rx_timeout(unsigned long data)
-{
-	struct hsu_dma_chan *chan = (void *)data;
-	struct uart_hsu_port *up = chan->uport;
-	struct hsu_dma_buffer *dbuf = &up->rxbuf;
-	int count = 0;
-	unsigned long flags;
-
-	spin_lock_irqsave(&up->port.lock, flags);
-
-	count = chan_readl(chan, HSU_CH_D0SAR) - dbuf->dma_addr;
-
-	if (!count) {
-		mod_timer(&chan->rx_timer, jiffies + HSU_DMA_TIMEOUT_CHECK_FREQ);
-		goto exit;
-	}
-
-	hsu_dma_rx(up, 0);
-exit:
-	spin_unlock_irqrestore(&up->port.lock, flags);
-}
-
 static void hsu_global_init(void)
 {
 	struct hsu_port *hsu;
@@ -1415,6 +1372,12 @@ static void hsu_global_init(void)
 
 		serial_hsu_ports[i] = uport;
 		uport->index = i;
+
+		if (hsu_dma_enable & (1<<i))
+			uport->use_dma = 1;
+		else
+			uport->use_dma = 0;
+
 		uport++;
 	}
 
@@ -1427,12 +1390,6 @@ static void hsu_global_init(void)
 		dchan->reg = hsu->reg + HSU_DMA_CHANS_REG_OFFSET +
 				i * HSU_DMA_CHANS_REG_LENGTH;
 
-		/* Work around for RX */
-		if (dchan->dirt == DMA_FROM_DEVICE) {
-			init_timer(&dchan->rx_timer);
-			dchan->rx_timer.function = hsu_dma_rx_timeout;
-			dchan->rx_timer.data = (unsigned long)dchan;
-		}
 		dchan++;
 	}
 

drivers/tty/serial/mpc52xx_uart.c

@@ -1302,8 +1302,7 @@ static struct of_device_id mpc52xx_uart_of_match[] = {
 	{},
 };
 
-static int __devinit
-mpc52xx_uart_of_probe(struct platform_device *op, const struct of_device_id *match)
+static int __devinit mpc52xx_uart_of_probe(struct platform_device *op)
 {
 	int idx = -1;
 	unsigned int uartclk;
@@ -1311,8 +1310,6 @@ mpc52xx_uart_of_probe(struct platform_device *op, const struct of_device_id *mat
 	struct resource res;
 	int ret;
 
-	dev_dbg(&op->dev, "mpc52xx_uart_probe(op=%p, match=%p)\n", op, match);
-
 	/* Check validity & presence */
 	for (idx = 0; idx < MPC52xx_PSC_MAXNUM; idx++)
 		if (mpc52xx_uart_nodes[idx] == op->dev.of_node)
@@ -1453,7 +1450,7 @@ mpc52xx_uart_of_enumerate(void)
 
 MODULE_DEVICE_TABLE(of, mpc52xx_uart_of_match);
 
-static struct of_platform_driver mpc52xx_uart_of_driver = {
+static struct platform_driver mpc52xx_uart_of_driver = {
 	.probe		= mpc52xx_uart_of_probe,
 	.remove		= mpc52xx_uart_of_remove,
 #ifdef CONFIG_PM
@@ -1497,9 +1494,9 @@ mpc52xx_uart_init(void)
 			return ret;
 	}
 
-	ret = of_register_platform_driver(&mpc52xx_uart_of_driver);
+	ret = platform_driver_register(&mpc52xx_uart_of_driver);
 	if (ret) {
-		printk(KERN_ERR "%s: of_register_platform_driver failed (%i)\n",
+		printk(KERN_ERR "%s: platform_driver_register failed (%i)\n",
 		       __FILE__, ret);
 		uart_unregister_driver(&mpc52xx_uart_driver);
 		return ret;
@@ -1514,7 +1511,7 @@ mpc52xx_uart_exit(void)
 	if (psc_ops->fifoc_uninit)
 		psc_ops->fifoc_uninit();
 
-	of_unregister_platform_driver(&mpc52xx_uart_of_driver);
+	platform_driver_unregister(&mpc52xx_uart_of_driver);
 	uart_unregister_driver(&mpc52xx_uart_driver);
 }
 

drivers/tty/serial/mrst_max3110.c

@@ -51,7 +51,7 @@
 struct uart_max3110 {
 	struct uart_port port;
 	struct spi_device *spi;
-	char name[24];
+	char name[SPI_NAME_SIZE];
 
 	wait_queue_head_t wq;
 	struct task_struct *main_thread;

drivers/tty/serial/msm_smd_tty.c

@@ -0,0 +1,236 @@
+/* drivers/tty/serial/msm_smd_tty.c
+ *
+ * Copyright (C) 2007 Google, Inc.
+ * Copyright (c) 2011, Code Aurora Forum. All rights reserved.
+ * Author: Brian Swetland <swetland@google.com>
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#include <linux/module.h>
+#include <linux/fs.h>
+#include <linux/cdev.h>
+#include <linux/device.h>
+#include <linux/wait.h>
+
+#include <linux/tty.h>
+#include <linux/tty_driver.h>
+#include <linux/tty_flip.h>
+
+#include <mach/msm_smd.h>
+
+#define MAX_SMD_TTYS 32
+
+struct smd_tty_info {
+	struct tty_port port;
+	smd_channel_t *ch;
+};
+
+struct smd_tty_channel_desc {
+	int id;
+	const char *name;
+};
+
+static struct smd_tty_info smd_tty[MAX_SMD_TTYS];
+
+static const struct smd_tty_channel_desc smd_default_tty_channels[] = {
+	{ .id = 0, .name = "SMD_DS" },
+	{ .id = 27, .name = "SMD_GPSNMEA" },
+};
+
+static const struct smd_tty_channel_desc *smd_tty_channels =
+		smd_default_tty_channels;
+static int smd_tty_channels_len = ARRAY_SIZE(smd_default_tty_channels);
+
+static void smd_tty_notify(void *priv, unsigned event)
+{
+	unsigned char *ptr;
+	int avail;
+	struct smd_tty_info *info = priv;
+	struct tty_struct *tty;
+
+	if (event != SMD_EVENT_DATA)
+		return;
+
+	tty = tty_port_tty_get(&info->port);
+	if (!tty)
+		return;
+
+	for (;;) {
+		if (test_bit(TTY_THROTTLED, &tty->flags))
+			break;
+		avail = smd_read_avail(info->ch);
+		if (avail == 0)
+			break;
+
+		avail = tty_prepare_flip_string(tty, &ptr, avail);
+
+		if (smd_read(info->ch, ptr, avail) != avail) {
+			/* shouldn't be possible since we're in interrupt
+			** context here and nobody else could 'steal' our
+			** characters.
+			*/
+			pr_err("OOPS - smd_tty_buffer mismatch?!");
+		}
+
+		tty_flip_buffer_push(tty);
+	}
+
+	/* XXX only when writable and necessary */
+	tty_wakeup(tty);
+	tty_kref_put(tty);
+}
+
+static int smd_tty_port_activate(struct tty_port *tport, struct tty_struct *tty)
+{
+	int i, res = 0;
+	int n = tty->index;
+	const char *name = NULL;
+	struct smd_tty_info *info = smd_tty + n;
+
+	for (i = 0; i < smd_tty_channels_len; i++) {
+		if (smd_tty_channels[i].id == n) {
+			name = smd_tty_channels[i].name;
+			break;
+		}
+	}
+	if (!name)
+		return -ENODEV;
+
+	if (info->ch)
+		smd_kick(info->ch);
+	else
+		res = smd_open(name, &info->ch, info, smd_tty_notify);
+
+	if (!res)
+		tty->driver_data = info;
+
+	return res;
+}
+
+static void smd_tty_port_shutdown(struct tty_port *tport)
+{
+	struct smd_tty_info *info;
+	struct tty_struct *tty = tty_port_tty_get(tport);
+
+	info = tty->driver_data;
+	if (info->ch) {
+		smd_close(info->ch);
+		info->ch = 0;
+	}
+
+	tty->driver_data = 0;
+	tty_kref_put(tty);
+}
+
+static int smd_tty_open(struct tty_struct *tty, struct file *f)
+{
+	struct smd_tty_info *info = smd_tty + tty->index;
+
+	return tty_port_open(&info->port, tty, f);
+}
+
+static void smd_tty_close(struct tty_struct *tty, struct file *f)
+{
+	struct smd_tty_info *info = tty->driver_data;
+
+	tty_port_close(&info->port, tty, f);
+}
+
+static int smd_tty_write(struct tty_struct *tty,
+			 const unsigned char *buf, int len)
+{
+	struct smd_tty_info *info = tty->driver_data;
+	int avail;
+
+	/* if we're writing to a packet channel we will
+	** never be able to write more data than there
+	** is currently space for
+	*/
+	avail = smd_write_avail(info->ch);
+	if (len > avail)
+		len = avail;
+
+	return smd_write(info->ch, buf, len);
+}
+
+static int smd_tty_write_room(struct tty_struct *tty)
+{
+	struct smd_tty_info *info = tty->driver_data;
+	return smd_write_avail(info->ch);
+}
+
+static int smd_tty_chars_in_buffer(struct tty_struct *tty)
+{
+	struct smd_tty_info *info = tty->driver_data;
+	return smd_read_avail(info->ch);
+}
+
+static void smd_tty_unthrottle(struct tty_struct *tty)
+{
+	struct smd_tty_info *info = tty->driver_data;
+	smd_kick(info->ch);
+}
+
+static const struct tty_port_operations smd_tty_port_ops = {
+	.shutdown = smd_tty_port_shutdown,
+	.activate = smd_tty_port_activate,
+};
+
+static const struct tty_operations smd_tty_ops = {
+	.open = smd_tty_open,
+	.close = smd_tty_close,
+	.write = smd_tty_write,
+	.write_room = smd_tty_write_room,
+	.chars_in_buffer = smd_tty_chars_in_buffer,
+	.unthrottle = smd_tty_unthrottle,
+};
+
+static struct tty_driver *smd_tty_driver;
+
+static int __init smd_tty_init(void)
+{
+	int ret, i;
+
+	smd_tty_driver = alloc_tty_driver(MAX_SMD_TTYS);
+	if (smd_tty_driver == 0)
+		return -ENOMEM;
+
+	smd_tty_driver->owner = THIS_MODULE;
+	smd_tty_driver->driver_name = "smd_tty_driver";
+	smd_tty_driver->name = "smd";
+	smd_tty_driver->major = 0;
+	smd_tty_driver->minor_start = 0;
+	smd_tty_driver->type = TTY_DRIVER_TYPE_SERIAL;
+	smd_tty_driver->subtype = SERIAL_TYPE_NORMAL;
+	smd_tty_driver->init_termios = tty_std_termios;
+	smd_tty_driver->init_termios.c_iflag = 0;
+	smd_tty_driver->init_termios.c_oflag = 0;
+	smd_tty_driver->init_termios.c_cflag = B38400 | CS8 | CREAD;
+	smd_tty_driver->init_termios.c_lflag = 0;
+	smd_tty_driver->flags = TTY_DRIVER_RESET_TERMIOS |
+		TTY_DRIVER_REAL_RAW | TTY_DRIVER_DYNAMIC_DEV;
+	tty_set_operations(smd_tty_driver, &smd_tty_ops);
+
+	ret = tty_register_driver(smd_tty_driver);
+	if (ret)
+		return ret;
+
+	for (i = 0; i < smd_tty_channels_len; i++) {
+		tty_port_init(&smd_tty[smd_tty_channels[i].id].port);
+		smd_tty[smd_tty_channels[i].id].port.ops = &smd_tty_port_ops;
+		tty_register_device(smd_tty_driver, smd_tty_channels[i].id, 0);
+	}
+
+	return 0;
+}
+
+module_init(smd_tty_init);

drivers/tty/serial/of_serial.c

@@ -80,14 +80,16 @@ static int __devinit of_platform_serial_setup(struct platform_device *ofdev,
 /*
  * Try to register a serial port
  */
-static int __devinit of_platform_serial_probe(struct platform_device *ofdev,
-						const struct of_device_id *id)
+static int __devinit of_platform_serial_probe(struct platform_device *ofdev)
 {
 	struct of_serial_info *info;
 	struct uart_port port;
 	int port_type;
 	int ret;
 
+	if (!ofdev->dev.of_match)
+		return -EINVAL;
+
 	if (of_find_property(ofdev->dev.of_node, "used-by-rtas", NULL))
 		return -EBUSY;
 
@@ -95,7 +97,7 @@ static int __devinit of_platform_serial_probe(struct platform_device *ofdev,
 	if (info == NULL)
 		return -ENOMEM;
 
-	port_type = (unsigned long)id->data;
+	port_type = (unsigned long)ofdev->dev.of_match->data;
 	ret = of_platform_serial_setup(ofdev, port_type, &port);
 	if (ret)
 		goto out;
@@ -160,21 +162,21 @@ static int of_platform_serial_remove(struct platform_device *ofdev)
  * A few common types, add more as needed.
  */
 static struct of_device_id __devinitdata of_platform_serial_table[] = {
-	{ .type = "serial", .compatible = "ns8250",   .data = (void *)PORT_8250, },
-	{ .type = "serial", .compatible = "ns16450",  .data = (void *)PORT_16450, },
-	{ .type = "serial", .compatible = "ns16550a", .data = (void *)PORT_16550A, },
-	{ .type = "serial", .compatible = "ns16550",  .data = (void *)PORT_16550, },
-	{ .type = "serial", .compatible = "ns16750",  .data = (void *)PORT_16750, },
-	{ .type = "serial", .compatible = "ns16850",  .data = (void *)PORT_16850, },
+	{ .compatible = "ns8250",   .data = (void *)PORT_8250, },
+	{ .compatible = "ns16450",  .data = (void *)PORT_16450, },
+	{ .compatible = "ns16550a", .data = (void *)PORT_16550A, },
+	{ .compatible = "ns16550",  .data = (void *)PORT_16550, },
+	{ .compatible = "ns16750",  .data = (void *)PORT_16750, },
+	{ .compatible = "ns16850",  .data = (void *)PORT_16850, },
 #ifdef CONFIG_SERIAL_OF_PLATFORM_NWPSERIAL
-	{ .type = "serial", .compatible = "ibm,qpace-nwp-serial",
-					.data = (void *)PORT_NWPSERIAL, },
+	{ .compatible = "ibm,qpace-nwp-serial",
+		.data = (void *)PORT_NWPSERIAL, },
 #endif
-	{ .type = "serial",			      .data = (void *)PORT_UNKNOWN, },
+	{ .type = "serial",         .data = (void *)PORT_UNKNOWN, },
 	{ /* end of list */ },
 };
 
-static struct of_platform_driver of_platform_serial_driver = {
+static struct platform_driver of_platform_serial_driver = {
 	.driver = {
 		.name = "of_serial",
 		.owner = THIS_MODULE,
@@ -186,13 +188,13 @@ static struct of_platform_driver of_platform_serial_driver = {
 
 static int __init of_platform_serial_init(void)
 {
-	return of_register_platform_driver(&of_platform_serial_driver);
+	return platform_driver_register(&of_platform_serial_driver);
 }
 module_init(of_platform_serial_init);
 
 static void __exit of_platform_serial_exit(void)
 {
-	return of_unregister_platform_driver(&of_platform_serial_driver);
+	return platform_driver_unregister(&of_platform_serial_driver);
 };
 module_exit(of_platform_serial_exit);
 

drivers/tty/serial/omap-serial.c

@@ -20,6 +20,10 @@
  * this driver as required for the omap-platform.
  */
 
+#if defined(CONFIG_SERIAL_OMAP_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
+#define SUPPORT_SYSRQ
+#endif
+
 #include <linux/module.h>
 #include <linux/init.h>
 #include <linux/console.h>
@@ -190,7 +194,6 @@ static inline void receive_chars(struct uart_omap_port *up, int *status)
 			if (up->port.line == up->port.cons->index) {
 				/* Recover the break flag from console xmit */
 				lsr |= up->lsr_break_flag;
-				up->lsr_break_flag = 0;
 			}
 #endif
 			if (lsr & UART_LSR_BI)
@@ -517,6 +520,9 @@ static int serial_omap_startup(struct uart_port *port)
 	up->ier = UART_IER_RLSI | UART_IER_RDI;
 	serial_out(up, UART_IER, up->ier);
 
+	/* Enable module level wake up */
+	serial_out(up, UART_OMAP_WER, OMAP_UART_WER_MOD_WKUP);
+
 	up->port_activity = jiffies;
 	return 0;
 }
@@ -824,9 +830,6 @@ serial_omap_pm(struct uart_port *port, unsigned int state,
 	serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
 	serial_out(up, UART_EFR, efr);
 	serial_out(up, UART_LCR, 0);
-	/* Enable module level wake up */
-	serial_out(up, UART_OMAP_WER,
-		(state != 0) ? OMAP_UART_WER_MOD_WKUP : 0);
 }
 
 static void serial_omap_release_port(struct uart_port *port)

drivers/tty/serial/pch_uart.c

@@ -21,6 +21,7 @@
 #include <linux/serial_core.h>
 #include <linux/interrupt.h>
 #include <linux/io.h>
+#include <linux/dmi.h>
 
 #include <linux/dmaengine.h>
 #include <linux/pch_dma.h>
@@ -40,10 +41,11 @@ enum {
 
 #define PCH_UART_DRIVER_DEVICE "ttyPCH"
 
-#define PCH_UART_NR_GE_256FIFO		1
-#define PCH_UART_NR_GE_64FIFO		3
-#define PCH_UART_NR_GE	(PCH_UART_NR_GE_256FIFO+PCH_UART_NR_GE_64FIFO)
-#define PCH_UART_NR	PCH_UART_NR_GE
+/* Set the max number of UART port
+ * Intel EG20T PCH: 4 port
+ * OKI SEMICONDUCTOR ML7213 IOH: 3 port
+*/
+#define PCH_UART_NR	4
 
 #define PCH_UART_HANDLED_RX_INT	(1<<((PCH_UART_HANDLED_RX_INT_SHIFT)<<1))
 #define PCH_UART_HANDLED_TX_INT	(1<<((PCH_UART_HANDLED_TX_INT_SHIFT)<<1))
@@ -192,6 +194,8 @@ enum {
 #define PCH_UART_HAL_LOOP		(PCH_UART_MCR_LOOP)
 #define PCH_UART_HAL_AFE		(PCH_UART_MCR_AFE)
 
+#define PCI_VENDOR_ID_ROHM		0x10DB
+
 struct pch_uart_buffer {
 	unsigned char *buf;
 	int size;
@@ -215,6 +219,7 @@ struct eg20t_port {
 	struct pch_uart_buffer rxbuf;
 	unsigned int dmsr;
 	unsigned int fcr;
+	unsigned int mcr;
 	unsigned int use_dma;
 	unsigned int use_dma_flag;
 	struct dma_async_tx_descriptor	*desc_tx;
@@ -223,13 +228,44 @@ struct eg20t_port {
 	struct pch_dma_slave		param_rx;
 	struct dma_chan			*chan_tx;
 	struct dma_chan			*chan_rx;
-	struct scatterlist		sg_tx;
+	struct scatterlist		*sg_tx_p;
+	int				nent;
 	struct scatterlist		sg_rx;
 	int				tx_dma_use;
 	void				*rx_buf_virt;
 	dma_addr_t			rx_buf_dma;
 };
 
+/**
+ * struct pch_uart_driver_data - private data structure for UART-DMA
+ * @port_type:			The number of DMA channel
+ * @line_no:			UART port line number (0, 1, 2...)
+ */
+struct pch_uart_driver_data {
+	int port_type;
+	int line_no;
+};
+
+enum pch_uart_num_t {
+	pch_et20t_uart0 = 0,
+	pch_et20t_uart1,
+	pch_et20t_uart2,
+	pch_et20t_uart3,
+	pch_ml7213_uart0,
+	pch_ml7213_uart1,
+	pch_ml7213_uart2,
+};
+
+static struct pch_uart_driver_data drv_dat[] = {
+	[pch_et20t_uart0] = {PCH_UART_8LINE, 0},
+	[pch_et20t_uart1] = {PCH_UART_2LINE, 1},
+	[pch_et20t_uart2] = {PCH_UART_2LINE, 2},
+	[pch_et20t_uart3] = {PCH_UART_2LINE, 3},
+	[pch_ml7213_uart0] = {PCH_UART_8LINE, 0},
+	[pch_ml7213_uart1] = {PCH_UART_2LINE, 1},
+	[pch_ml7213_uart2] = {PCH_UART_2LINE, 2},
+};
+
 static unsigned int default_baud = 9600;
 static const int trigger_level_256[4] = { 1, 64, 128, 224 };
 static const int trigger_level_64[4] = { 1, 16, 32, 56 };
@@ -278,7 +314,7 @@ static int pch_uart_hal_set_line(struct eg20t_port *priv, int baud,
 
 	div = DIV_ROUND(priv->base_baud / 16, baud);
 	if (div < 0 || USHRT_MAX <= div) {
-		pr_err("Invalid Baud(div=0x%x)\n", div);
+		dev_err(priv->port.dev, "Invalid Baud(div=0x%x)\n", div);
 		return -EINVAL;
 	}
 
@@ -286,17 +322,17 @@ static int pch_uart_hal_set_line(struct eg20t_port *priv, int baud,
 	dlm = ((unsigned int)div >> 8) & 0x00FFU;
 
 	if (parity & ~(PCH_UART_LCR_PEN | PCH_UART_LCR_EPS | PCH_UART_LCR_SP)) {
-		pr_err("Invalid parity(0x%x)\n", parity);
+		dev_err(priv->port.dev, "Invalid parity(0x%x)\n", parity);
 		return -EINVAL;
 	}
 
 	if (bits & ~PCH_UART_LCR_WLS) {
-		pr_err("Invalid bits(0x%x)\n", bits);
+		dev_err(priv->port.dev, "Invalid bits(0x%x)\n", bits);
 		return -EINVAL;
 	}
 
 	if (stb & ~PCH_UART_LCR_STB) {
-		pr_err("Invalid STB(0x%x)\n", stb);
+		dev_err(priv->port.dev, "Invalid STB(0x%x)\n", stb);
 		return -EINVAL;
 	}
 
@@ -304,7 +340,7 @@ static int pch_uart_hal_set_line(struct eg20t_port *priv, int baud,
 	lcr |= bits;
 	lcr |= stb;
 
-	pr_debug("%s:baud = %d, div = %04x, lcr = %02x (%lu)\n",
+	dev_dbg(priv->port.dev, "%s:baud = %d, div = %04x, lcr = %02x (%lu)\n",
 		 __func__, baud, div, lcr, jiffies);
 	iowrite8(PCH_UART_LCR_DLAB, priv->membase + UART_LCR);
 	iowrite8(dll, priv->membase + PCH_UART_DLL);
@@ -318,7 +354,8 @@ static int pch_uart_hal_fifo_reset(struct eg20t_port *priv,
 				    unsigned int flag)
 {
 	if (flag & ~(PCH_UART_FCR_TFR | PCH_UART_FCR_RFR)) {
-		pr_err("%s:Invalid flag(0x%x)\n", __func__, flag);
+		dev_err(priv->port.dev, "%s:Invalid flag(0x%x)\n",
+			__func__, flag);
 		return -EINVAL;
 	}
 
@@ -337,17 +374,20 @@ static int pch_uart_hal_set_fifo(struct eg20t_port *priv,
 	u8 fcr;
 
 	if (dmamode & ~PCH_UART_FCR_DMS) {
-		pr_err("%s:Invalid DMA Mode(0x%x)\n", __func__, dmamode);
+		dev_err(priv->port.dev, "%s:Invalid DMA Mode(0x%x)\n",
+			__func__, dmamode);
 		return -EINVAL;
 	}
 
 	if (fifo_size & ~(PCH_UART_FCR_FIFOE | PCH_UART_FCR_FIFO256)) {
-		pr_err("%s:Invalid FIFO SIZE(0x%x)\n", __func__, fifo_size);
+		dev_err(priv->port.dev, "%s:Invalid FIFO SIZE(0x%x)\n",
+			__func__, fifo_size);
 		return -EINVAL;
 	}
 
 	if (trigger & ~PCH_UART_FCR_RFTL) {
-		pr_err("%s:Invalid TRIGGER(0x%x)\n", __func__, trigger);
+		dev_err(priv->port.dev, "%s:Invalid TRIGGER(0x%x)\n",
+			__func__, trigger);
 		return -EINVAL;
 	}
 
@@ -386,7 +426,7 @@ static u8 pch_uart_hal_get_modem(struct eg20t_port *priv)
 	return get_msr(priv, priv->membase);
 }
 
-static int pch_uart_hal_write(struct eg20t_port *priv,
+static void pch_uart_hal_write(struct eg20t_port *priv,
 			      const unsigned char *buf, int tx_size)
 {
 	int i;
@@ -396,7 +436,6 @@ static int pch_uart_hal_write(struct eg20t_port *priv,
 		thr = buf[i++];
 		iowrite8(thr, priv->membase + PCH_UART_THR);
 	}
-	return i;
 }
 
 static int pch_uart_hal_read(struct eg20t_port *priv, unsigned char *buf,
@@ -452,7 +491,7 @@ static int push_rx(struct eg20t_port *priv, const unsigned char *buf,
 	port = &priv->port;
 	tty = tty_port_tty_get(&port->state->port);
 	if (!tty) {
-		pr_debug("%s:tty is busy now", __func__);
+		dev_dbg(priv->port.dev, "%s:tty is busy now", __func__);
 		return -EBUSY;
 	}
 
@@ -469,8 +508,8 @@ static int pop_tx_x(struct eg20t_port *priv, unsigned char *buf)
 	struct uart_port *port = &priv->port;
 
 	if (port->x_char) {
-		pr_debug("%s:X character send %02x (%lu)\n", __func__,
-			port->x_char, jiffies);
+		dev_dbg(priv->port.dev, "%s:X character send %02x (%lu)\n",
+			__func__, port->x_char, jiffies);
 		buf[0] = port->x_char;
 		port->x_char = 0;
 		ret = 1;
@@ -490,7 +529,7 @@ static int dma_push_rx(struct eg20t_port *priv, int size)
 	port = &priv->port;
 	tty = tty_port_tty_get(&port->state->port);
 	if (!tty) {
-		pr_debug("%s:tty is busy now", __func__);
+		dev_dbg(priv->port.dev, "%s:tty is busy now", __func__);
 		return 0;
 	}
 
@@ -560,11 +599,13 @@ static void pch_request_dma(struct uart_port *port)
 	/* Set Tx DMA */
 	param = &priv->param_tx;
 	param->dma_dev = &dma_dev->dev;
-	param->chan_id = priv->port.line;
+	param->chan_id = priv->port.line * 2; /* Tx = 0, 2, 4, ... */
+
 	param->tx_reg = port->mapbase + UART_TX;
 	chan = dma_request_channel(mask, filter, param);
 	if (!chan) {
-		pr_err("%s:dma_request_channel FAILS(Tx)\n", __func__);
+		dev_err(priv->port.dev, "%s:dma_request_channel FAILS(Tx)\n",
+			__func__);
 		return;
 	}
 	priv->chan_tx = chan;
@@ -572,11 +613,13 @@ static void pch_request_dma(struct uart_port *port)
 	/* Set Rx DMA */
 	param = &priv->param_rx;
 	param->dma_dev = &dma_dev->dev;
-	param->chan_id = priv->port.line + 1; /* Rx = Tx + 1 */
+	param->chan_id = priv->port.line * 2 + 1; /* Rx = Tx + 1 */
+
 	param->rx_reg = port->mapbase + UART_RX;
 	chan = dma_request_channel(mask, filter, param);
 	if (!chan) {
-		pr_err("%s:dma_request_channel FAILS(Rx)\n", __func__);
+		dev_err(priv->port.dev, "%s:dma_request_channel FAILS(Rx)\n",
+			__func__);
 		dma_release_channel(priv->chan_tx);
 		return;
 	}
@@ -592,16 +635,20 @@ static void pch_dma_rx_complete(void *arg)
 	struct eg20t_port *priv = arg;
 	struct uart_port *port = &priv->port;
 	struct tty_struct *tty = tty_port_tty_get(&port->state->port);
+	int count;
 
 	if (!tty) {
-		pr_debug("%s:tty is busy now", __func__);
+		dev_dbg(priv->port.dev, "%s:tty is busy now", __func__);
 		return;
 	}
 
-	if (dma_push_rx(priv, priv->trigger_level))
+	dma_sync_sg_for_cpu(port->dev, &priv->sg_rx, 1, DMA_FROM_DEVICE);
+	count = dma_push_rx(priv, priv->trigger_level);
+	if (count)
 		tty_flip_buffer_push(tty);
-
 	tty_kref_put(tty);
+	async_tx_ack(priv->desc_rx);
+	pch_uart_hal_enable_interrupt(priv, PCH_UART_HAL_RX_INT);
 }
 
 static void pch_dma_tx_complete(void *arg)
@@ -609,16 +656,23 @@ static void pch_dma_tx_complete(void *arg)
 	struct eg20t_port *priv = arg;
 	struct uart_port *port = &priv->port;
 	struct circ_buf *xmit = &port->state->xmit;
+	struct scatterlist *sg = priv->sg_tx_p;
+	int i;
 
-	xmit->tail += sg_dma_len(&priv->sg_tx);
+	for (i = 0; i < priv->nent; i++, sg++) {
+		xmit->tail += sg_dma_len(sg);
+		port->icount.tx += sg_dma_len(sg);
+	}
 	xmit->tail &= UART_XMIT_SIZE - 1;
-	port->icount.tx += sg_dma_len(&priv->sg_tx);
-
 	async_tx_ack(priv->desc_tx);
+	dma_unmap_sg(port->dev, sg, priv->nent, DMA_TO_DEVICE);
 	priv->tx_dma_use = 0;
+	priv->nent = 0;
+	kfree(priv->sg_tx_p);
+	pch_uart_hal_enable_interrupt(priv, PCH_UART_HAL_TX_INT);
 }
 
-static int pop_tx(struct eg20t_port *priv, unsigned char *buf, int size)
+static int pop_tx(struct eg20t_port *priv, int size)
 {
 	int count = 0;
 	struct uart_port *port = &priv->port;
@@ -631,13 +685,13 @@ static int pop_tx(struct eg20t_port *priv, unsigned char *buf, int size)
 		int cnt_to_end =
 		    CIRC_CNT_TO_END(xmit->head, xmit->tail, UART_XMIT_SIZE);
 		int sz = min(size - count, cnt_to_end);
-		memcpy(&buf[count], &xmit->buf[xmit->tail], sz);
+		pch_uart_hal_write(priv, &xmit->buf[xmit->tail], sz);
 		xmit->tail = (xmit->tail + sz) & (UART_XMIT_SIZE - 1);
 		count += sz;
 	} while (!uart_circ_empty(xmit) && count < size);
 
 pop_tx_end:
-	pr_debug("%d characters. Remained %d characters. (%lu)\n",
+	dev_dbg(priv->port.dev, "%d characters. Remained %d characters.(%lu)\n",
 		 count, size - count, jiffies);
 
 	return count;
@@ -679,7 +733,7 @@ static int dma_handle_rx(struct eg20t_port *priv)
 
 	sg_init_table(&priv->sg_rx, 1); /* Initialize SG table */
 
-	sg_dma_len(sg) = priv->fifo_size;
+	sg_dma_len(sg) = priv->trigger_level;
 
 	sg_set_page(&priv->sg_rx, virt_to_page(priv->rx_buf_virt),
 		     sg_dma_len(sg), (unsigned long)priv->rx_buf_virt &
@@ -689,7 +743,8 @@ static int dma_handle_rx(struct eg20t_port *priv)
 
 	desc = priv->chan_rx->device->device_prep_slave_sg(priv->chan_rx,
 			sg, 1, DMA_FROM_DEVICE,
-			DMA_PREP_INTERRUPT);
+			DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
+
 	if (!desc)
 		return 0;
 
@@ -706,14 +761,14 @@ static unsigned int handle_tx(struct eg20t_port *priv)
 {
 	struct uart_port *port = &priv->port;
 	struct circ_buf *xmit = &port->state->xmit;
-	int ret;
 	int fifo_size;
 	int tx_size;
 	int size;
 	int tx_empty;
 
 	if (!priv->start_tx) {
-		pr_info("%s:Tx isn't started. (%lu)\n", __func__, jiffies);
+		dev_info(priv->port.dev, "%s:Tx isn't started. (%lu)\n",
+			__func__, jiffies);
 		pch_uart_hal_disable_interrupt(priv, PCH_UART_HAL_TX_INT);
 		priv->tx_empty = 1;
 		return 0;
@@ -728,17 +783,21 @@ static unsigned int handle_tx(struct eg20t_port *priv)
 		fifo_size--;
 	}
 	size = min(xmit->head - xmit->tail, fifo_size);
-	tx_size = pop_tx(priv, xmit->buf, size);
+	if (size < 0)
+		size = fifo_size;
+
+	tx_size = pop_tx(priv, size);
 	if (tx_size > 0) {
-		ret = pch_uart_hal_write(priv, xmit->buf, tx_size);
-		port->icount.tx += ret;
+		port->icount.tx += tx_size;
 		tx_empty = 0;
 	}
 
 	priv->tx_empty = tx_empty;
 
-	if (tx_empty)
+	if (tx_empty) {
 		pch_uart_hal_disable_interrupt(priv, PCH_UART_HAL_TX_INT);
+		uart_write_wakeup(port);
+	}
 
 	return PCH_UART_HANDLED_TX_INT;
 }
@@ -747,14 +806,28 @@ static unsigned int dma_handle_tx(struct eg20t_port *priv)
 {
 	struct uart_port *port = &priv->port;
 	struct circ_buf *xmit = &port->state->xmit;
-	struct scatterlist *sg = &priv->sg_tx;
+	struct scatterlist *sg;
 	int nent;
 	int fifo_size;
 	int tx_empty;
 	struct dma_async_tx_descriptor *desc;
+	int num;
+	int i;
+	int bytes;
+	int size;
+	int rem;
 
 	if (!priv->start_tx) {
-		pr_info("%s:Tx isn't started. (%lu)\n", __func__, jiffies);
+		dev_info(priv->port.dev, "%s:Tx isn't started. (%lu)\n",
+			__func__, jiffies);
+		pch_uart_hal_disable_interrupt(priv, PCH_UART_HAL_TX_INT);
+		priv->tx_empty = 1;
+		return 0;
+	}
+
+	if (priv->tx_dma_use) {
+		dev_dbg(priv->port.dev, "%s:Tx is not completed. (%lu)\n",
+			__func__, jiffies);
 		pch_uart_hal_disable_interrupt(priv, PCH_UART_HAL_TX_INT);
 		priv->tx_empty = 1;
 		return 0;
@@ -769,37 +842,73 @@ static unsigned int dma_handle_tx(struct eg20t_port *priv)
 		fifo_size--;
 	}
 
-	pch_uart_hal_disable_interrupt(priv, PCH_UART_HAL_TX_INT);
+	bytes = min((int)CIRC_CNT(xmit->head, xmit->tail,
+			     UART_XMIT_SIZE), CIRC_CNT_TO_END(xmit->head,
+			     xmit->tail, UART_XMIT_SIZE));
+	if (!bytes) {
+		dev_dbg(priv->port.dev, "%s 0 bytes return\n", __func__);
+		pch_uart_hal_disable_interrupt(priv, PCH_UART_HAL_TX_INT);
+		uart_write_wakeup(port);
+		return 0;
+	}
+
+	if (bytes > fifo_size) {
+		num = bytes / fifo_size + 1;
+		size = fifo_size;
+		rem = bytes % fifo_size;
+	} else {
+		num = 1;
+		size = bytes;
+		rem = bytes;
+	}
+
+	dev_dbg(priv->port.dev, "%s num=%d size=%d rem=%d\n",
+		__func__, num, size, rem);
 
 	priv->tx_dma_use = 1;
 
-	sg_init_table(&priv->sg_tx, 1); /* Initialize SG table */
+	priv->sg_tx_p = kzalloc(sizeof(struct scatterlist)*num, GFP_ATOMIC);
 
-	sg_set_page(&priv->sg_tx, virt_to_page(xmit->buf),
-		    UART_XMIT_SIZE, (int)xmit->buf & ~PAGE_MASK);
+	sg_init_table(priv->sg_tx_p, num); /* Initialize SG table */
+	sg = priv->sg_tx_p;
 
-	nent = dma_map_sg(port->dev, &priv->sg_tx, 1, DMA_TO_DEVICE);
-	if (!nent) {
-		pr_err("%s:dma_map_sg Failed\n", __func__);
-		return 0;
+	for (i = 0; i < num; i++, sg++) {
+		if (i == (num - 1))
+			sg_set_page(sg, virt_to_page(xmit->buf),
+				    rem, fifo_size * i);
+		else
+			sg_set_page(sg, virt_to_page(xmit->buf),
+				    size, fifo_size * i);
 	}
 
-	sg->offset = xmit->tail & (UART_XMIT_SIZE - 1);
-	sg_dma_address(sg) = (sg_dma_address(sg) & ~(UART_XMIT_SIZE - 1)) +
-			      sg->offset;
-	sg_dma_len(sg) = min((int)CIRC_CNT(xmit->head, xmit->tail,
-			     UART_XMIT_SIZE), CIRC_CNT_TO_END(xmit->head,
-			     xmit->tail, UART_XMIT_SIZE));
+	sg = priv->sg_tx_p;
+	nent = dma_map_sg(port->dev, sg, num, DMA_TO_DEVICE);
+	if (!nent) {
+		dev_err(priv->port.dev, "%s:dma_map_sg Failed\n", __func__);
+		return 0;
+	}
+	priv->nent = nent;
+
+	for (i = 0; i < nent; i++, sg++) {
+		sg->offset = (xmit->tail & (UART_XMIT_SIZE - 1)) +
+			      fifo_size * i;
+		sg_dma_address(sg) = (sg_dma_address(sg) &
+				    ~(UART_XMIT_SIZE - 1)) + sg->offset;
+		if (i == (nent - 1))
+			sg_dma_len(sg) = rem;
+		else
+			sg_dma_len(sg) = size;
+	}
 
 	desc = priv->chan_tx->device->device_prep_slave_sg(priv->chan_tx,
-		sg, nent, DMA_TO_DEVICE, DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
+					priv->sg_tx_p, nent, DMA_TO_DEVICE,
+					DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
 	if (!desc) {
-		pr_err("%s:device_prep_slave_sg Failed\n", __func__);
+		dev_err(priv->port.dev, "%s:device_prep_slave_sg Failed\n",
+			__func__);
 		return 0;
 	}
-
-	dma_sync_sg_for_device(port->dev, sg, 1, DMA_TO_DEVICE);
-
+	dma_sync_sg_for_device(port->dev, priv->sg_tx_p, nent, DMA_TO_DEVICE);
 	priv->desc_tx = desc;
 	desc->callback = pch_dma_tx_complete;
 	desc->callback_param = priv;
@@ -854,10 +963,16 @@ static irqreturn_t pch_uart_interrupt(int irq, void *dev_id)
 			}
 			break;
 		case PCH_UART_IID_RDR:	/* Received Data Ready */
-			if (priv->use_dma)
+			if (priv->use_dma) {
+				pch_uart_hal_disable_interrupt(priv,
+							PCH_UART_HAL_RX_INT);
 				ret = dma_handle_rx(priv);
-			else
+				if (!ret)
+					pch_uart_hal_enable_interrupt(priv,
+							PCH_UART_HAL_RX_INT);
+			} else {
 				ret = handle_rx(priv);
+			}
 			break;
 		case PCH_UART_IID_RDR_TO:	/* Received Data Ready
 						   (FIFO Timeout) */
@@ -874,7 +989,8 @@ static irqreturn_t pch_uart_interrupt(int irq, void *dev_id)
 			ret = PCH_UART_HANDLED_MS_INT;
 			break;
 		default:	/* Never junp to this label */
-			pr_err("%s:iid=%d (%lu)\n", __func__, iid, jiffies);
+			dev_err(priv->port.dev, "%s:iid=%d (%lu)\n", __func__,
+				iid, jiffies);
 			ret = -1;
 			break;
 		}
@@ -932,7 +1048,6 @@ static unsigned int pch_uart_get_mctrl(struct uart_port *port)
 static void pch_uart_set_mctrl(struct uart_port *port, unsigned int mctrl)
 {
 	u32 mcr = 0;
-	unsigned int dat;
 	struct eg20t_port *priv = container_of(port, struct eg20t_port, port);
 
 	if (mctrl & TIOCM_DTR)
@@ -942,11 +1057,11 @@ static void pch_uart_set_mctrl(struct uart_port *port, unsigned int mctrl)
 	if (mctrl & TIOCM_LOOP)
 		mcr |= UART_MCR_LOOP;
 
-	if (mctrl) {
-		dat = pch_uart_get_mctrl(port);
-		dat |= mcr;
-		iowrite8(dat, priv->membase + UART_MCR);
-	}
+	if (priv->mcr & UART_MCR_AFE)
+		mcr |= UART_MCR_AFE;
+
+	if (mctrl)
+		iowrite8(mcr, priv->membase + UART_MCR);
 }
 
 static void pch_uart_stop_tx(struct uart_port *port)
@@ -963,9 +1078,13 @@ static void pch_uart_start_tx(struct uart_port *port)
 
 	priv = container_of(port, struct eg20t_port, port);
 
-	if (priv->use_dma)
-		if (priv->tx_dma_use)
+	if (priv->use_dma) {
+		if (priv->tx_dma_use) {
+			dev_dbg(priv->port.dev, "%s : Tx DMA is NOT empty.\n",
+				__func__);
 			return;
+		}
+	}
 
 	priv->start_tx = 1;
 	pch_uart_hal_enable_interrupt(priv, PCH_UART_HAL_TX_INT);
@@ -1010,7 +1129,12 @@ static int pch_uart_startup(struct uart_port *port)
 
 	priv = container_of(port, struct eg20t_port, port);
 	priv->tx_empty = 1;
-	port->uartclk = priv->base_baud;
+
+	if (port->uartclk)
+		priv->base_baud = port->uartclk;
+	else
+		port->uartclk = priv->base_baud;
+
 	pch_uart_hal_disable_interrupt(priv, PCH_UART_HAL_ALL_INT);
 	ret = pch_uart_hal_set_line(priv, default_baud,
 			      PCH_UART_HAL_PARITY_NONE, PCH_UART_HAL_8BIT,
@@ -1081,7 +1205,8 @@ static void pch_uart_shutdown(struct uart_port *port)
 	ret = pch_uart_hal_set_fifo(priv, PCH_UART_HAL_DMA_MODE0,
 			      PCH_UART_HAL_FIFO_DIS, PCH_UART_HAL_TRIGGER1);
 	if (ret)
-		pr_err("pch_uart_hal_set_fifo Failed(ret=%d)\n", ret);
+		dev_err(priv->port.dev,
+			"pch_uart_hal_set_fifo Failed(ret=%d)\n", ret);
 
 	if (priv->use_dma_flag)
 		pch_free_dma(port);
@@ -1130,6 +1255,13 @@ static void pch_uart_set_termios(struct uart_port *port,
 	} else {
 		parity = PCH_UART_HAL_PARITY_NONE;
 	}
+
+	/* Only UART0 has auto hardware flow function */
+	if ((termios->c_cflag & CRTSCTS) && (priv->fifo_size == 256))
+		priv->mcr |= UART_MCR_AFE;
+	else
+		priv->mcr &= ~UART_MCR_AFE;
+
 	termios->c_cflag &= ~CMSPAR; /* Mark/Space parity is not supported */
 
 	baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk / 16);
@@ -1202,17 +1334,19 @@ static int pch_uart_verify_port(struct uart_port *port,
 
 	priv = container_of(port, struct eg20t_port, port);
 	if (serinfo->flags & UPF_LOW_LATENCY) {
-		pr_info("PCH UART : Use PIO Mode (without DMA)\n");
+		dev_info(priv->port.dev,
+			"PCH UART : Use PIO Mode (without DMA)\n");
 		priv->use_dma = 0;
 		serinfo->flags &= ~UPF_LOW_LATENCY;
 	} else {
 #ifndef CONFIG_PCH_DMA
-		pr_err("%s : PCH DMA is not Loaded.\n", __func__);
+		dev_err(priv->port.dev, "%s : PCH DMA is not Loaded.\n",
+			__func__);
 		return -EOPNOTSUPP;
 #endif
 		priv->use_dma = 1;
 		priv->use_dma_flag = 1;
-		pr_info("PCH UART : Use DMA Mode\n");
+		dev_info(priv->port.dev, "PCH UART : Use DMA Mode\n");
 	}
 
 	return 0;
@@ -1249,7 +1383,7 @@ static struct uart_driver pch_uart_driver = {
 };
 
 static struct eg20t_port *pch_uart_init_port(struct pci_dev *pdev,
-						int port_type)
+					     const struct pci_device_id *id)
 {
 	struct eg20t_port *priv;
 	int ret;
@@ -1257,7 +1391,11 @@ static struct eg20t_port *pch_uart_init_port(struct pci_dev *pdev,
 	unsigned int mapbase;
 	unsigned char *rxbuf;
 	int fifosize, base_baud;
-	static int num;
+	int port_type;
+	struct pch_uart_driver_data *board;
+
+	board = &drv_dat[id->driver_data];
+	port_type = board->port_type;
 
 	priv = kzalloc(sizeof(struct eg20t_port), GFP_KERNEL);
 	if (priv == NULL)
@@ -1267,14 +1405,18 @@ static struct eg20t_port *pch_uart_init_port(struct pci_dev *pdev,
 	if (!rxbuf)
 		goto init_port_free_txbuf;
 
+	base_baud = 1843200; /* 1.8432MHz */
+
+	/* quirk for CM-iTC board */
+	if (strstr(dmi_get_system_info(DMI_BOARD_NAME), "CM-iTC"))
+		base_baud = 192000000; /* 192.0MHz */
+
 	switch (port_type) {
 	case PORT_UNKNOWN:
-		fifosize = 256; /* UART0 */
-		base_baud = 1843200; /* 1.8432MHz */
+		fifosize = 256; /* EG20T/ML7213: UART0 */
 		break;
 	case PORT_8250:
-		fifosize = 64; /* UART1~3 */
-		base_baud = 1843200; /* 1.8432MHz */
+		fifosize = 64; /* EG20T:UART1~3  ML7213: UART1~2*/
 		break;
 	default:
 		dev_err(&pdev->dev, "Invalid Port Type(=%d)\n", port_type);
@@ -1302,11 +1444,14 @@ static struct eg20t_port *pch_uart_init_port(struct pci_dev *pdev,
 	priv->port.ops = &pch_uart_ops;
 	priv->port.flags = UPF_BOOT_AUTOCONF;
 	priv->port.fifosize = fifosize;
-	priv->port.line = num++;
+	priv->port.line = board->line_no;
 	priv->trigger = PCH_UART_HAL_TRIGGER_M;
 
+	spin_lock_init(&priv->port.lock);
+
 	pci_set_drvdata(pdev, priv);
 	pch_uart_hal_request(pdev, fifosize, base_baud);
+
 	ret = uart_add_one_port(&pch_uart_driver, &priv->port);
 	if (ret < 0)
 		goto init_port_hal_free;
@@ -1377,13 +1522,19 @@ static int pch_uart_pci_resume(struct pci_dev *pdev)
 
 static DEFINE_PCI_DEVICE_TABLE(pch_uart_pci_id) = {
 	{PCI_DEVICE(PCI_VENDOR_ID_INTEL, 0x8811),
-	 .driver_data = PCH_UART_8LINE},
+	 .driver_data = pch_et20t_uart0},
 	{PCI_DEVICE(PCI_VENDOR_ID_INTEL, 0x8812),
-	 .driver_data = PCH_UART_2LINE},
+	 .driver_data = pch_et20t_uart1},
 	{PCI_DEVICE(PCI_VENDOR_ID_INTEL, 0x8813),
-	 .driver_data = PCH_UART_2LINE},
+	 .driver_data = pch_et20t_uart2},
 	{PCI_DEVICE(PCI_VENDOR_ID_INTEL, 0x8814),
-	 .driver_data = PCH_UART_2LINE},
+	 .driver_data = pch_et20t_uart3},
+	{PCI_DEVICE(PCI_VENDOR_ID_ROHM, 0x8027),
+	 .driver_data = pch_ml7213_uart0},
+	{PCI_DEVICE(PCI_VENDOR_ID_ROHM, 0x8028),
+	 .driver_data = pch_ml7213_uart1},
+	{PCI_DEVICE(PCI_VENDOR_ID_ROHM, 0x8029),
+	 .driver_data = pch_ml7213_uart2},
 	{0,},
 };
 
@@ -1397,7 +1548,7 @@ static int __devinit pch_uart_pci_probe(struct pci_dev *pdev,
 	if (ret < 0)
 		goto probe_error;
 
-	priv = pch_uart_init_port(pdev, id->driver_data);
+	priv = pch_uart_init_port(pdev, id);
 	if (!priv) {
 		ret = -EBUSY;
 		goto probe_disable_device;

drivers/tty/serial/serial_core.c

@@ -905,7 +905,7 @@ static int uart_get_lsr_info(struct tty_struct *tty,
 	return put_user(result, value);
 }
 
-static int uart_tiocmget(struct tty_struct *tty, struct file *file)
+static int uart_tiocmget(struct tty_struct *tty)
 {
 	struct uart_state *state = tty->driver_data;
 	struct tty_port *port = &state->port;
@@ -913,10 +913,8 @@ static int uart_tiocmget(struct tty_struct *tty, struct file *file)
 	int result = -EIO;
 
 	mutex_lock(&port->mutex);
-	if ((!file || !tty_hung_up_p(file)) &&
-	    !(tty->flags & (1 << TTY_IO_ERROR))) {
+	if (!(tty->flags & (1 << TTY_IO_ERROR))) {
 		result = uport->mctrl;
-
 		spin_lock_irq(&uport->lock);
 		result |= uport->ops->get_mctrl(uport);
 		spin_unlock_irq(&uport->lock);
@@ -927,8 +925,7 @@ static int uart_tiocmget(struct tty_struct *tty, struct file *file)
 }
 
 static int
-uart_tiocmset(struct tty_struct *tty, struct file *file,
-	      unsigned int set, unsigned int clear)
+uart_tiocmset(struct tty_struct *tty, unsigned int set, unsigned int clear)
 {
 	struct uart_state *state = tty->driver_data;
 	struct uart_port *uport = state->uart_port;
@@ -936,8 +933,7 @@ uart_tiocmset(struct tty_struct *tty, struct file *file,
 	int ret = -EIO;
 
 	mutex_lock(&port->mutex);
-	if ((!file || !tty_hung_up_p(file)) &&
-	    !(tty->flags & (1 << TTY_IO_ERROR))) {
+	if (!(tty->flags & (1 << TTY_IO_ERROR))) {
 		uart_update_mctrl(uport, set, clear);
 		ret = 0;
 	}
@@ -1103,7 +1099,7 @@ static int uart_get_icount(struct tty_struct *tty,
  * Called via sys_ioctl.  We can use spin_lock_irq() here.
  */
 static int
-uart_ioctl(struct tty_struct *tty, struct file *filp, unsigned int cmd,
+uart_ioctl(struct tty_struct *tty, unsigned int cmd,
 	   unsigned long arg)
 {
 	struct uart_state *state = tty->driver_data;
@@ -1156,7 +1152,7 @@ uart_ioctl(struct tty_struct *tty, struct file *filp, unsigned int cmd,
 
 	mutex_lock(&port->mutex);
 
-	if (tty_hung_up_p(filp)) {
+	if (tty->flags & (1 << TTY_IO_ERROR)) {
 		ret = -EIO;
 		goto out_up;
 	}
@@ -2064,7 +2060,7 @@ int uart_resume_port(struct uart_driver *drv, struct uart_port *uport)
 	/*
 	 * Re-enable the console device after suspending.
 	 */
-	if (console_suspend_enabled && uart_console(uport)) {
+	if (uart_console(uport)) {
 		/*
 		 * First try to use the console cflag setting.
 		 */
@@ -2077,9 +2073,9 @@ int uart_resume_port(struct uart_driver *drv, struct uart_port *uport)
 		if (port->tty && port->tty->termios && termios.c_cflag == 0)
 			termios = *(port->tty->termios);
 
-		uart_change_pm(state, 0);
 		uport->ops->set_termios(uport, &termios, NULL);
-		console_start(uport->cons);
+		if (console_suspend_enabled)
+			console_start(uport->cons);
 	}
 
 	if (port->flags & ASYNC_SUSPENDED) {

drivers/tty/serial/serial_cs.c

@@ -712,6 +712,7 @@ static struct pcmcia_device_id serial_ids[] = {
 	PCMCIA_PFC_DEVICE_PROD_ID12(1, "Xircom", "CreditCard Ethernet+Modem II", 0x2e3ee845, 0xeca401bf),
 	PCMCIA_PFC_DEVICE_MANF_CARD(1, 0x0032, 0x0e01),
 	PCMCIA_PFC_DEVICE_MANF_CARD(1, 0x0032, 0x0a05),
+	PCMCIA_PFC_DEVICE_MANF_CARD(1, 0x0032, 0x0b05),
 	PCMCIA_PFC_DEVICE_MANF_CARD(1, 0x0032, 0x1101),
 	PCMCIA_MFC_DEVICE_MANF_CARD(0, 0x0104, 0x0070),
 	PCMCIA_MFC_DEVICE_MANF_CARD(1, 0x0101, 0x0562),

drivers/tty/serial/serial_lh7a40x.c

@@ -1,682 +0,0 @@
-/* drivers/serial/serial_lh7a40x.c
- *
- *  Copyright (C) 2004 Coastal Environmental Systems
- *
- *  This program is free software; you can redistribute it and/or
- *  modify it under the terms of the GNU General Public License
- *  version 2 as published by the Free Software Foundation.
- *
- */
-
-/* Driver for Sharp LH7A40X embedded serial ports
- *
- *  Based on drivers/char/serial.c, by Linus Torvalds, Theodore Ts'o.
- *  Based on drivers/serial/amba.c, by Deep Blue Solutions Ltd.
- *
- *  ---
- *
- * This driver supports the embedded UARTs of the Sharp LH7A40X series
- * CPUs.  While similar to the 16550 and other UART chips, there is
- * nothing close to register compatibility.  Moreover, some of the
- * modem control lines are not available, either in the chip or they
- * are lacking in the board-level implementation.
- *
- * - Use of SIRDIS
- *   For simplicity, we disable the IR functions of any UART whenever
- *   we enable it.
- *
- */
-
-
-#if defined(CONFIG_SERIAL_LH7A40X_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
-#define SUPPORT_SYSRQ
-#endif
-
-#include <linux/module.h>
-#include <linux/ioport.h>
-#include <linux/init.h>
-#include <linux/console.h>
-#include <linux/sysrq.h>
-#include <linux/tty.h>
-#include <linux/tty_flip.h>
-#include <linux/serial_core.h>
-#include <linux/serial.h>
-#include <linux/io.h>
-
-#include <asm/irq.h>
-#include <mach/hardware.h>
-
-#define DEV_MAJOR	204
-#define DEV_MINOR	16
-#define DEV_NR		3
-
-#define ISR_LOOP_LIMIT	256
-
-#define UR(p,o)	_UR ((p)->membase, o)
-#define _UR(b,o) (*((volatile unsigned int*)(((unsigned char*) b) + (o))))
-#define BIT_CLR(p,o,m)	UR(p,o) = UR(p,o) & (~(unsigned int)m)
-#define BIT_SET(p,o,m)	UR(p,o) = UR(p,o) | ( (unsigned int)m)
-
-#define UART_REG_SIZE	32
-
-#define UART_R_DATA	(0x00)
-#define UART_R_FCON	(0x04)
-#define UART_R_BRCON	(0x08)
-#define UART_R_CON	(0x0c)
-#define UART_R_STATUS	(0x10)
-#define UART_R_RAWISR	(0x14)
-#define UART_R_INTEN	(0x18)
-#define UART_R_ISR	(0x1c)
-
-#define UARTEN		(0x01)		/* UART enable */
-#define SIRDIS		(0x02)		/* Serial IR disable (UART1 only) */
-
-#define RxEmpty		(0x10)
-#define TxEmpty		(0x80)
-#define TxFull		(0x20)
-#define nRxRdy		RxEmpty
-#define nTxRdy		TxFull
-#define TxBusy		(0x08)
-
-#define RxBreak		(0x0800)
-#define RxOverrunError	(0x0400)
-#define RxParityError	(0x0200)
-#define RxFramingError	(0x0100)
-#define RxError     (RxBreak | RxOverrunError | RxParityError | RxFramingError)
-
-#define DCD		(0x04)
-#define DSR		(0x02)
-#define CTS		(0x01)
-
-#define RxInt		(0x01)
-#define TxInt		(0x02)
-#define ModemInt	(0x04)
-#define RxTimeoutInt	(0x08)
-
-#define MSEOI		(0x10)
-
-#define WLEN_8		(0x60)
-#define WLEN_7		(0x40)
-#define WLEN_6		(0x20)
-#define WLEN_5		(0x00)
-#define WLEN		(0x60)	/* Mask for all word-length bits */
-#define STP2		(0x08)
-#define PEN		(0x02)	/* Parity Enable */
-#define EPS		(0x04)	/* Even Parity Set */
-#define FEN		(0x10)	/* FIFO Enable */
-#define BRK		(0x01)	/* Send Break */
-
-
-struct uart_port_lh7a40x {
-	struct uart_port port;
-	unsigned int statusPrev; /* Most recently read modem status */
-};
-
-static void lh7a40xuart_stop_tx (struct uart_port* port)
-{
-	BIT_CLR (port, UART_R_INTEN, TxInt);
-}
-
-static void lh7a40xuart_start_tx (struct uart_port* port)
-{
-	BIT_SET (port, UART_R_INTEN, TxInt);
-
-	/* *** FIXME: do I need to check for startup of the
-		      transmitter?  The old driver did, but AMBA
-		      doesn't . */
-}
-
-static void lh7a40xuart_stop_rx (struct uart_port* port)
-{
-	BIT_SET (port, UART_R_INTEN, RxTimeoutInt | RxInt);
-}
-
-static void lh7a40xuart_enable_ms (struct uart_port* port)
-{
-	BIT_SET (port, UART_R_INTEN, ModemInt);
-}
-
-static void lh7a40xuart_rx_chars (struct uart_port* port)
-{
-	struct tty_struct* tty = port->state->port.tty;
-	int cbRxMax = 256;	/* (Gross) limit on receive */
-	unsigned int data;	/* Received data and status */
-	unsigned int flag;
-
-	while (!(UR (port, UART_R_STATUS) & nRxRdy) && --cbRxMax) {
-		data = UR (port, UART_R_DATA);
-		flag = TTY_NORMAL;
-		++port->icount.rx;
-
-		if (unlikely(data & RxError)) {
-			if (data & RxBreak) {
-				data &= ~(RxFramingError | RxParityError);
-				++port->icount.brk;
-				if (uart_handle_break (port))
-					continue;
-			}
-			else if (data & RxParityError)
-				++port->icount.parity;
-			else if (data & RxFramingError)
-				++port->icount.frame;
-			if (data & RxOverrunError)
-				++port->icount.overrun;
-
-				/* Mask by termios, leave Rx'd byte */
-			data &= port->read_status_mask | 0xff;
-
-			if (data & RxBreak)
-				flag = TTY_BREAK;
-			else if (data & RxParityError)
-				flag = TTY_PARITY;
-			else if (data & RxFramingError)
-				flag = TTY_FRAME;
-		}
-
-		if (uart_handle_sysrq_char (port, (unsigned char) data))
-			continue;
-
-		uart_insert_char(port, data, RxOverrunError, data, flag);
-	}
-	tty_flip_buffer_push (tty);
-	return;
-}
-
-static void lh7a40xuart_tx_chars (struct uart_port* port)
-{
-	struct circ_buf* xmit = &port->state->xmit;
-	int cbTxMax = port->fifosize;
-
-	if (port->x_char) {
-		UR (port, UART_R_DATA) = port->x_char;
-		++port->icount.tx;
-		port->x_char = 0;
-		return;
-	}
-	if (uart_circ_empty (xmit) || uart_tx_stopped (port)) {
-		lh7a40xuart_stop_tx (port);
-		return;
-	}
-
-	/* Unlike the AMBA UART, the lh7a40x UART does not guarantee
-	   that at least half of the FIFO is empty.  Instead, we check
-	   status for every character.  Using the AMBA method causes
-	   the transmitter to drop characters. */
-
-	do {
-		UR (port, UART_R_DATA) = xmit->buf[xmit->tail];
-		xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
-		++port->icount.tx;
-		if (uart_circ_empty(xmit))
-			break;
-	} while (!(UR (port, UART_R_STATUS) & nTxRdy)
-		 && cbTxMax--);
-
-	if (uart_circ_chars_pending (xmit) < WAKEUP_CHARS)
-		uart_write_wakeup (port);
-
-	if (uart_circ_empty (xmit))
-		lh7a40xuart_stop_tx (port);
-}
-
-static void lh7a40xuart_modem_status (struct uart_port* port)
-{
-	unsigned int status = UR (port, UART_R_STATUS);
-	unsigned int delta
-		= status ^ ((struct uart_port_lh7a40x*) port)->statusPrev;
-
-	BIT_SET (port, UART_R_RAWISR, MSEOI); /* Clear modem status intr */
-
-	if (!delta)		/* Only happens if we missed 2 transitions */
-		return;
-
-	((struct uart_port_lh7a40x*) port)->statusPrev = status;
-
-	if (delta & DCD)
-		uart_handle_dcd_change (port, status & DCD);
-
-	if (delta & DSR)
-		++port->icount.dsr;
-
-	if (delta & CTS)
-		uart_handle_cts_change (port, status & CTS);
-
-	wake_up_interruptible (&port->state->port.delta_msr_wait);
-}
-
-static irqreturn_t lh7a40xuart_int (int irq, void* dev_id)
-{
-	struct uart_port* port = dev_id;
-	unsigned int cLoopLimit = ISR_LOOP_LIMIT;
-	unsigned int isr = UR (port, UART_R_ISR);
-
-
-	do {
-		if (isr & (RxInt | RxTimeoutInt))
-			lh7a40xuart_rx_chars(port);
-		if (isr & ModemInt)
-			lh7a40xuart_modem_status (port);
-		if (isr & TxInt)
-			lh7a40xuart_tx_chars (port);
-
-		if (--cLoopLimit == 0)
-			break;
-
-		isr = UR (port, UART_R_ISR);
-	} while (isr & (RxInt | TxInt | RxTimeoutInt));
-
-	return IRQ_HANDLED;
-}
-
-static unsigned int lh7a40xuart_tx_empty (struct uart_port* port)
-{
-	return (UR (port, UART_R_STATUS) & TxEmpty) ? TIOCSER_TEMT : 0;
-}
-
-static unsigned int lh7a40xuart_get_mctrl (struct uart_port* port)
-{
-	unsigned int result = 0;
-	unsigned int status = UR (port, UART_R_STATUS);
-
-	if (status & DCD)
-		result |= TIOCM_CAR;
-	if (status & DSR)
-		result |= TIOCM_DSR;
-	if (status & CTS)
-		result |= TIOCM_CTS;
-
-	return result;
-}
-
-static void lh7a40xuart_set_mctrl (struct uart_port* port, unsigned int mctrl)
-{
-	/* None of the ports supports DTR. UART1 supports RTS through GPIO. */
-	/* Note, kernel appears to be setting DTR and RTS on console. */
-
-	/* *** FIXME: this deserves more work.  There's some work in
-	       tracing all of the IO pins. */
-#if 0
-	if( port->mapbase == UART1_PHYS) {
-		gpioRegs_t *gpio = (gpioRegs_t *)IO_ADDRESS(GPIO_PHYS);
-
-		if (mctrl & TIOCM_RTS)
-			gpio->pbdr &= ~GPIOB_UART1_RTS;
-		else
-			gpio->pbdr |= GPIOB_UART1_RTS;
-	}
-#endif
-}
-
-static void lh7a40xuart_break_ctl (struct uart_port* port, int break_state)
-{
-	unsigned long flags;
-
-	spin_lock_irqsave(&port->lock, flags);
-	if (break_state == -1)
-		BIT_SET (port, UART_R_FCON, BRK); /* Assert break */
-	else
-		BIT_CLR (port, UART_R_FCON, BRK); /* Deassert break */
-	spin_unlock_irqrestore(&port->lock, flags);
-}
-
-static int lh7a40xuart_startup (struct uart_port* port)
-{
-	int retval;
-
-	retval = request_irq (port->irq, lh7a40xuart_int, 0,
-			      "serial_lh7a40x", port);
-	if (retval)
-		return retval;
-
-				/* Initial modem control-line settings */
-	((struct uart_port_lh7a40x*) port)->statusPrev
-		= UR (port, UART_R_STATUS);
-
-	/* There is presently no configuration option to enable IR.
-	   Thus, we always disable it. */
-
-	BIT_SET (port, UART_R_CON, UARTEN | SIRDIS);
-	BIT_SET (port, UART_R_INTEN, RxTimeoutInt | RxInt);
-
-	return 0;
-}
-
-static void lh7a40xuart_shutdown (struct uart_port* port)
-{
-	free_irq (port->irq, port);
-	BIT_CLR (port, UART_R_FCON, BRK | FEN);
-	BIT_CLR (port, UART_R_CON, UARTEN);
-}
-
-static void lh7a40xuart_set_termios (struct uart_port* port,
-				     struct ktermios* termios,
-				     struct ktermios* old)
-{
-	unsigned int con;
-	unsigned int inten;
-	unsigned int fcon;
-	unsigned long flags;
-	unsigned int baud;
-	unsigned int quot;
-
-	baud = uart_get_baud_rate (port, termios, old, 8, port->uartclk/16);
-	quot = uart_get_divisor (port, baud); /* -1 performed elsewhere */
-
-	switch (termios->c_cflag & CSIZE) {
-	case CS5:
-		fcon = WLEN_5;
-		break;
-	case CS6:
-		fcon = WLEN_6;
-		break;
-	case CS7:
-		fcon = WLEN_7;
-		break;
-	case CS8:
-	default:
-		fcon = WLEN_8;
-		break;
-	}
-	if (termios->c_cflag & CSTOPB)
-		fcon |= STP2;
-	if (termios->c_cflag & PARENB) {
-		fcon |= PEN;
-		if (!(termios->c_cflag & PARODD))
-			fcon |= EPS;
-	}
-	if (port->fifosize > 1)
-		fcon |= FEN;
-
-	spin_lock_irqsave (&port->lock, flags);
-
-	uart_update_timeout (port, termios->c_cflag, baud);
-
-	port->read_status_mask = RxOverrunError;
-	if (termios->c_iflag & INPCK)
-		port->read_status_mask |= RxFramingError | RxParityError;
-	if (termios->c_iflag & (BRKINT | PARMRK))
-		port->read_status_mask |= RxBreak;
-
-		/* Figure mask for status we ignore */
-	port->ignore_status_mask = 0;
-	if (termios->c_iflag & IGNPAR)
-		port->ignore_status_mask |= RxFramingError | RxParityError;
-	if (termios->c_iflag & IGNBRK) {
-		port->ignore_status_mask |= RxBreak;
-		/* Ignore overrun when ignorning parity */
-		/* *** FIXME: is this in the right place? */
-		if (termios->c_iflag & IGNPAR)
-			port->ignore_status_mask |= RxOverrunError;
-	}
-
-		/* Ignore all receive errors when receive disabled */
-	if ((termios->c_cflag & CREAD) == 0)
-		port->ignore_status_mask |= RxError;
-
-	con   = UR (port, UART_R_CON);
-	inten = (UR (port, UART_R_INTEN) & ~ModemInt);
-
-	if (UART_ENABLE_MS (port, termios->c_cflag))
-		inten |= ModemInt;
-
-	BIT_CLR (port, UART_R_CON, UARTEN);	/* Disable UART */
-	UR (port, UART_R_INTEN) = 0;		/* Disable interrupts */
-	UR (port, UART_R_BRCON) = quot - 1;	/* Set baud rate divisor */
-	UR (port, UART_R_FCON)  = fcon;		/* Set FIFO and frame ctrl */
-	UR (port, UART_R_INTEN) = inten;	/* Enable interrupts */
-	UR (port, UART_R_CON)   = con;		/* Restore UART mode */
-
-	spin_unlock_irqrestore(&port->lock, flags);
-}
-
-static const char* lh7a40xuart_type (struct uart_port* port)
-{
-	return port->type == PORT_LH7A40X ? "LH7A40X" : NULL;
-}
-
-static void lh7a40xuart_release_port (struct uart_port* port)
-{
-	release_mem_region (port->mapbase, UART_REG_SIZE);
-}
-
-static int lh7a40xuart_request_port (struct uart_port* port)
-{
-	return request_mem_region (port->mapbase, UART_REG_SIZE,
-				   "serial_lh7a40x") != NULL
-		? 0 : -EBUSY;
-}
-
-static void lh7a40xuart_config_port (struct uart_port* port, int flags)
-{
-	if (flags & UART_CONFIG_TYPE) {
-		port->type = PORT_LH7A40X;
-		lh7a40xuart_request_port (port);
-	}
-}
-
-static int lh7a40xuart_verify_port (struct uart_port* port,
-				    struct serial_struct* ser)
-{
-	int ret = 0;
-
-	if (ser->type != PORT_UNKNOWN && ser->type != PORT_LH7A40X)
-		ret = -EINVAL;
-	if (ser->irq < 0 || ser->irq >= nr_irqs)
-		ret = -EINVAL;
-	if (ser->baud_base < 9600) /* *** FIXME: is this true? */
-		ret = -EINVAL;
-	return ret;
-}
-
-static struct uart_ops lh7a40x_uart_ops = {
-	.tx_empty	= lh7a40xuart_tx_empty,
-	.set_mctrl	= lh7a40xuart_set_mctrl,
-	.get_mctrl	= lh7a40xuart_get_mctrl,
-	.stop_tx	= lh7a40xuart_stop_tx,
-	.start_tx	= lh7a40xuart_start_tx,
-	.stop_rx	= lh7a40xuart_stop_rx,
-	.enable_ms	= lh7a40xuart_enable_ms,
-	.break_ctl	= lh7a40xuart_break_ctl,
-	.startup	= lh7a40xuart_startup,
-	.shutdown	= lh7a40xuart_shutdown,
-	.set_termios	= lh7a40xuart_set_termios,
-	.type		= lh7a40xuart_type,
-	.release_port	= lh7a40xuart_release_port,
-	.request_port	= lh7a40xuart_request_port,
-	.config_port	= lh7a40xuart_config_port,
-	.verify_port	= lh7a40xuart_verify_port,
-};
-
-static struct uart_port_lh7a40x lh7a40x_ports[DEV_NR] = {
-	{
-		.port = {
-			.membase	= (void*) io_p2v (UART1_PHYS),
-			.mapbase	= UART1_PHYS,
-			.iotype		= UPIO_MEM,
-			.irq		= IRQ_UART1INTR,
-			.uartclk	= 14745600/2,
-			.fifosize	= 16,
-			.ops		= &lh7a40x_uart_ops,
-			.flags		= UPF_BOOT_AUTOCONF,
-			.line		= 0,
-		},
-	},
-	{
-		.port = {
-			.membase	= (void*) io_p2v (UART2_PHYS),
-			.mapbase	= UART2_PHYS,
-			.iotype		= UPIO_MEM,
-			.irq		= IRQ_UART2INTR,
-			.uartclk	= 14745600/2,
-			.fifosize	= 16,
-			.ops		= &lh7a40x_uart_ops,
-			.flags		= UPF_BOOT_AUTOCONF,
-			.line		= 1,
-		},
-	},
-	{
-		.port = {
-			.membase	= (void*) io_p2v (UART3_PHYS),
-			.mapbase	= UART3_PHYS,
-			.iotype		= UPIO_MEM,
-			.irq		= IRQ_UART3INTR,
-			.uartclk	= 14745600/2,
-			.fifosize	= 16,
-			.ops		= &lh7a40x_uart_ops,
-			.flags		= UPF_BOOT_AUTOCONF,
-			.line		= 2,
-		},
-	},
-};
-
-#ifndef CONFIG_SERIAL_LH7A40X_CONSOLE
-# define LH7A40X_CONSOLE NULL
-#else
-# define LH7A40X_CONSOLE &lh7a40x_console
-
-static void lh7a40xuart_console_putchar(struct uart_port *port, int ch)
-{
-	while (UR(port, UART_R_STATUS) & nTxRdy)
-		;
-	UR(port, UART_R_DATA) = ch;
-}
-
-static void lh7a40xuart_console_write (struct console* co,
-				       const char* s,
-				       unsigned int count)
-{
-	struct uart_port* port = &lh7a40x_ports[co->index].port;
-	unsigned int con = UR (port, UART_R_CON);
-	unsigned int inten = UR (port, UART_R_INTEN);
-
-
-	UR (port, UART_R_INTEN) = 0;		/* Disable all interrupts */
-	BIT_SET (port, UART_R_CON, UARTEN | SIRDIS); /* Enable UART */
-
-	uart_console_write(port, s, count, lh7a40xuart_console_putchar);
-
-				/* Wait until all characters are sent */
-	while (UR (port, UART_R_STATUS) & TxBusy)
-		;
-
-				/* Restore control and interrupt mask */
-	UR (port, UART_R_CON) = con;
-	UR (port, UART_R_INTEN) = inten;
-}
-
-static void __init lh7a40xuart_console_get_options (struct uart_port* port,
-						    int* baud,
-						    int* parity,
-						    int* bits)
-{
-	if (UR (port, UART_R_CON) & UARTEN) {
-		unsigned int fcon = UR (port, UART_R_FCON);
-		unsigned int quot = UR (port, UART_R_BRCON) + 1;
-
-		switch (fcon & (PEN | EPS)) {
-		default:        *parity = 'n'; break;
-		case PEN:       *parity = 'o'; break;
-		case PEN | EPS: *parity = 'e'; break;
-		}
-
-		switch (fcon & WLEN) {
-		default:
-		case WLEN_8: *bits = 8; break;
-		case WLEN_7: *bits = 7; break;
-		case WLEN_6: *bits = 6; break;
-		case WLEN_5: *bits = 5; break;
-		}
-
-		*baud = port->uartclk/(16*quot);
-	}
-}
-
-static int __init lh7a40xuart_console_setup (struct console* co, char* options)
-{
-	struct uart_port* port;
-	int baud = 38400;
-	int bits = 8;
-	int parity = 'n';
-	int flow = 'n';
-
-	if (co->index >= DEV_NR) /* Bounds check on device number */
-		co->index = 0;
-	port = &lh7a40x_ports[co->index].port;
-
-	if (options)
-		uart_parse_options (options, &baud, &parity, &bits, &flow);
-	else
-		lh7a40xuart_console_get_options (port, &baud, &parity, &bits);
-
-	return uart_set_options (port, co, baud, parity, bits, flow);
-}
-
-static struct uart_driver lh7a40x_reg;
-static struct console lh7a40x_console = {
-	.name		= "ttyAM",
-	.write		= lh7a40xuart_console_write,
-	.device		= uart_console_device,
-	.setup		= lh7a40xuart_console_setup,
-	.flags		= CON_PRINTBUFFER,
-	.index		= -1,
-	.data		= &lh7a40x_reg,
-};
-
-static int __init lh7a40xuart_console_init(void)
-{
-	register_console (&lh7a40x_console);
-	return 0;
-}
-
-console_initcall (lh7a40xuart_console_init);
-
-#endif
-
-static struct uart_driver lh7a40x_reg = {
-	.owner			= THIS_MODULE,
-	.driver_name		= "ttyAM",
-	.dev_name		= "ttyAM",
-	.major			= DEV_MAJOR,
-	.minor			= DEV_MINOR,
-	.nr			= DEV_NR,
-	.cons			= LH7A40X_CONSOLE,
-};
-
-static int __init lh7a40xuart_init(void)
-{
-	int ret;
-
-	printk (KERN_INFO "serial: LH7A40X serial driver\n");
-
-	ret = uart_register_driver (&lh7a40x_reg);
-
-	if (ret == 0) {
-		int i;
-
-		for (i = 0; i < DEV_NR; i++) {
-			/* UART3, when used, requires GPIO pin reallocation */
-			if (lh7a40x_ports[i].port.mapbase == UART3_PHYS)
-				GPIO_PINMUX |= 1<<3;
-			uart_add_one_port (&lh7a40x_reg,
-					   &lh7a40x_ports[i].port);
-		}
-	}
-	return ret;
-}
-
-static void __exit lh7a40xuart_exit(void)
-{
-	int i;
-
-	for (i = 0; i < DEV_NR; i++)
-		uart_remove_one_port (&lh7a40x_reg, &lh7a40x_ports[i].port);
-
-	uart_unregister_driver (&lh7a40x_reg);
-}
-
-module_init (lh7a40xuart_init);
-module_exit (lh7a40xuart_exit);
-
-MODULE_AUTHOR ("Marc Singer");
-MODULE_DESCRIPTION ("Sharp LH7A40X serial port driver");
-MODULE_LICENSE ("GPL");

drivers/tty/serial/sunhv.c

@@ -519,7 +519,7 @@ static struct console sunhv_console = {
 	.data	=	&sunhv_reg,
 };
 
-static int __devinit hv_probe(struct platform_device *op, const struct of_device_id *match)
+static int __devinit hv_probe(struct platform_device *op)
 {
 	struct uart_port *port;
 	unsigned long minor;
@@ -629,7 +629,7 @@ static const struct of_device_id hv_match[] = {
 };
 MODULE_DEVICE_TABLE(of, hv_match);
 
-static struct of_platform_driver hv_driver = {
+static struct platform_driver hv_driver = {
 	.driver = {
 		.name = "hv",
 		.owner = THIS_MODULE,
@@ -644,12 +644,12 @@ static int __init sunhv_init(void)
 	if (tlb_type != hypervisor)
 		return -ENODEV;
 
-	return of_register_platform_driver(&hv_driver);
+	return platform_driver_register(&hv_driver);
 }
 
 static void __exit sunhv_exit(void)
 {
-	of_unregister_platform_driver(&hv_driver);
+	platform_driver_unregister(&hv_driver);
 }
 
 module_init(sunhv_init);

drivers/tty/serial/sunsab.c

@@ -1006,7 +1006,7 @@ static int __devinit sunsab_init_one(struct uart_sunsab_port *up,
 	return 0;
 }
 
-static int __devinit sab_probe(struct platform_device *op, const struct of_device_id *match)
+static int __devinit sab_probe(struct platform_device *op)
 {
 	static int inst;
 	struct uart_sunsab_port *up;
@@ -1092,7 +1092,7 @@ static const struct of_device_id sab_match[] = {
 };
 MODULE_DEVICE_TABLE(of, sab_match);
 
-static struct of_platform_driver sab_driver = {
+static struct platform_driver sab_driver = {
 	.driver = {
 		.name = "sab",
 		.owner = THIS_MODULE,
@@ -1130,12 +1130,12 @@ static int __init sunsab_init(void)
 		}
 	}
 
-	return of_register_platform_driver(&sab_driver);
+	return platform_driver_register(&sab_driver);
 }
 
 static void __exit sunsab_exit(void)
 {
-	of_unregister_platform_driver(&sab_driver);
+	platform_driver_unregister(&sab_driver);
 	if (sunsab_reg.nr) {
 		sunserial_unregister_minors(&sunsab_reg, sunsab_reg.nr);
 	}

drivers/tty/serial/sunsu.c

@@ -1406,7 +1406,7 @@ static enum su_type __devinit su_get_type(struct device_node *dp)
 	return SU_PORT_PORT;
 }
 
-static int __devinit su_probe(struct platform_device *op, const struct of_device_id *match)
+static int __devinit su_probe(struct platform_device *op)
 {
 	static int inst;
 	struct device_node *dp = op->dev.of_node;
@@ -1543,7 +1543,7 @@ static const struct of_device_id su_match[] = {
 };
 MODULE_DEVICE_TABLE(of, su_match);
 
-static struct of_platform_driver su_driver = {
+static struct platform_driver su_driver = {
 	.driver = {
 		.name = "su",
 		.owner = THIS_MODULE,
@@ -1586,7 +1586,7 @@ static int __init sunsu_init(void)
 			return err;
 	}
 
-	err = of_register_platform_driver(&su_driver);
+	err = platform_driver_register(&su_driver);
 	if (err && num_uart)
 		sunserial_unregister_minors(&sunsu_reg, num_uart);
 

drivers/tty/serial/sunzilog.c

@@ -1399,7 +1399,7 @@ static void __devinit sunzilog_init_hw(struct uart_sunzilog_port *up)
 
 static int zilog_irq = -1;
 
-static int __devinit zs_probe(struct platform_device *op, const struct of_device_id *match)
+static int __devinit zs_probe(struct platform_device *op)
 {
 	static int kbm_inst, uart_inst;
 	int inst;
@@ -1540,7 +1540,7 @@ static const struct of_device_id zs_match[] = {
 };
 MODULE_DEVICE_TABLE(of, zs_match);
 
-static struct of_platform_driver zs_driver = {
+static struct platform_driver zs_driver = {
 	.driver = {
 		.name = "zs",
 		.owner = THIS_MODULE,
@@ -1576,7 +1576,7 @@ static int __init sunzilog_init(void)
 			goto out_free_tables;
 	}
 
-	err = of_register_platform_driver(&zs_driver);
+	err = platform_driver_register(&zs_driver);
 	if (err)
 		goto out_unregister_uart;
 
@@ -1604,7 +1604,7 @@ out:
 	return err;
 
 out_unregister_driver:
-	of_unregister_platform_driver(&zs_driver);
+	platform_driver_unregister(&zs_driver);
 
 out_unregister_uart:
 	if (num_sunzilog) {
@@ -1619,7 +1619,7 @@ out_free_tables:
 
 static void __exit sunzilog_exit(void)
 {
-	of_unregister_platform_driver(&zs_driver);
+	platform_driver_unregister(&zs_driver);
 
 	if (zilog_irq != -1) {
 		struct uart_sunzilog_port *up = sunzilog_irq_chain;

drivers/tty/serial/uartlite.c

@@ -19,22 +19,11 @@
 #include <linux/interrupt.h>
 #include <linux/init.h>
 #include <asm/io.h>
-#if defined(CONFIG_OF) && (defined(CONFIG_PPC32) || defined(CONFIG_MICROBLAZE))
 #include <linux/of.h>
 #include <linux/of_address.h>
 #include <linux/of_device.h>
 #include <linux/of_platform.h>
 
-/* Match table for of_platform binding */
-static struct of_device_id ulite_of_match[] __devinitdata = {
-	{ .compatible = "xlnx,opb-uartlite-1.00.b", },
-	{ .compatible = "xlnx,xps-uartlite-1.00.a", },
-	{}
-};
-MODULE_DEVICE_TABLE(of, ulite_of_match);
-
-#endif
-
 #define ULITE_NAME		"ttyUL"
 #define ULITE_MAJOR		204
 #define ULITE_MINOR		187
@@ -571,9 +560,29 @@ static int __devexit ulite_release(struct device *dev)
  * Platform bus binding
  */
 
+#if defined(CONFIG_OF)
+/* Match table for of_platform binding */
+static struct of_device_id ulite_of_match[] __devinitdata = {
+	{ .compatible = "xlnx,opb-uartlite-1.00.b", },
+	{ .compatible = "xlnx,xps-uartlite-1.00.a", },
+	{}
+};
+MODULE_DEVICE_TABLE(of, ulite_of_match);
+#else /* CONFIG_OF */
+#define ulite_of_match NULL
+#endif /* CONFIG_OF */
+
 static int __devinit ulite_probe(struct platform_device *pdev)
 {
 	struct resource *res, *res2;
+	int id = pdev->id;
+#ifdef CONFIG_OF
+	const __be32 *prop;
+
+	prop = of_get_property(pdev->dev.of_node, "port-number", NULL);
+	if (prop)
+		id = be32_to_cpup(prop);
+#endif
 
 	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 	if (!res)
@@ -583,7 +592,7 @@ static int __devinit ulite_probe(struct platform_device *pdev)
 	if (!res2)
 		return -ENODEV;
 
-	return ulite_assign(&pdev->dev, pdev->id, res->start, res2->start);
+	return ulite_assign(&pdev->dev, id, res->start, res2->start);
 }
 
 static int __devexit ulite_remove(struct platform_device *pdev)
@@ -595,72 +604,15 @@ static int __devexit ulite_remove(struct platform_device *pdev)
 MODULE_ALIAS("platform:uartlite");
 
 static struct platform_driver ulite_platform_driver = {
-	.probe	= ulite_probe,
-	.remove	= __devexit_p(ulite_remove),
-	.driver	= {
-		   .owner = THIS_MODULE,
-		   .name  = "uartlite",
-		   },
-};
-
-/* ---------------------------------------------------------------------
- * OF bus bindings
- */
-#if defined(CONFIG_OF) && (defined(CONFIG_PPC32) || defined(CONFIG_MICROBLAZE))
-static int __devinit
-ulite_of_probe(struct platform_device *op, const struct of_device_id *match)
-{
-	struct resource res;
-	const unsigned int *id;
-	int irq, rc;
-
-	dev_dbg(&op->dev, "%s(%p, %p)\n", __func__, op, match);
-
-	rc = of_address_to_resource(op->dev.of_node, 0, &res);
-	if (rc) {
-		dev_err(&op->dev, "invalid address\n");
-		return rc;
-	}
-
-	irq = irq_of_parse_and_map(op->dev.of_node, 0);
-
-	id = of_get_property(op->dev.of_node, "port-number", NULL);
-
-	return ulite_assign(&op->dev, id ? *id : -1, res.start, irq);
-}
-
-static int __devexit ulite_of_remove(struct platform_device *op)
-{
-	return ulite_release(&op->dev);
-}
-
-static struct of_platform_driver ulite_of_driver = {
-	.probe = ulite_of_probe,
-	.remove = __devexit_p(ulite_of_remove),
+	.probe = ulite_probe,
+	.remove = __devexit_p(ulite_remove),
 	.driver = {
-		.name = "uartlite",
 		.owner = THIS_MODULE,
+		.name  = "uartlite",
 		.of_match_table = ulite_of_match,
 	},
 };
 
-/* Registration helpers to keep the number of #ifdefs to a minimum */
-static inline int __init ulite_of_register(void)
-{
-	pr_debug("uartlite: calling of_register_platform_driver()\n");
-	return of_register_platform_driver(&ulite_of_driver);
-}
-
-static inline void __exit ulite_of_unregister(void)
-{
-	of_unregister_platform_driver(&ulite_of_driver);
-}
-#else /* CONFIG_OF && (CONFIG_PPC32 || CONFIG_MICROBLAZE) */
-/* Appropriate config not enabled; do nothing helpers */
-static inline int __init ulite_of_register(void) { return 0; }
-static inline void __exit ulite_of_unregister(void) { }
-#endif /* CONFIG_OF && (CONFIG_PPC32 || CONFIG_MICROBLAZE) */
-
 /* ---------------------------------------------------------------------
  * Module setup/teardown
  */
@@ -674,10 +626,6 @@ int __init ulite_init(void)
 	if (ret)
 		goto err_uart;
 
-	ret = ulite_of_register();
-	if (ret)
-		goto err_of;
-
 	pr_debug("uartlite: calling platform_driver_register()\n");
 	ret = platform_driver_register(&ulite_platform_driver);
 	if (ret)
@@ -686,8 +634,6 @@ int __init ulite_init(void)
 	return 0;
 
 err_plat:
-	ulite_of_unregister();
-err_of:
 	uart_unregister_driver(&ulite_uart_driver);
 err_uart:
 	printk(KERN_ERR "registering uartlite driver failed: err=%i", ret);
@@ -697,7 +643,6 @@ err_uart:
 void __exit ulite_exit(void)
 {
 	platform_driver_unregister(&ulite_platform_driver);
-	ulite_of_unregister();
 	uart_unregister_driver(&ulite_uart_driver);
 }
 

drivers/tty/serial/ucc_uart.c

@@ -1194,8 +1194,7 @@ static void uart_firmware_cont(const struct firmware *fw, void *context)
 	release_firmware(fw);
 }
 
-static int ucc_uart_probe(struct platform_device *ofdev,
-	const struct of_device_id *match)
+static int ucc_uart_probe(struct platform_device *ofdev)
 {
 	struct device_node *np = ofdev->dev.of_node;
 	const unsigned int *iprop;      /* Integer OF properties */
@@ -1485,7 +1484,7 @@ static struct of_device_id ucc_uart_match[] = {
 };
 MODULE_DEVICE_TABLE(of, ucc_uart_match);
 
-static struct of_platform_driver ucc_uart_of_driver = {
+static struct platform_driver ucc_uart_of_driver = {
 	.driver = {
 		.name = "ucc_uart",
 		.owner = THIS_MODULE,
@@ -1510,7 +1509,7 @@ static int __init ucc_uart_init(void)
 		return ret;
 	}
 
-	ret = of_register_platform_driver(&ucc_uart_of_driver);
+	ret = platform_driver_register(&ucc_uart_of_driver);
 	if (ret)
 		printk(KERN_ERR
 		       "ucc-uart: could not register platform driver\n");
@@ -1523,7 +1522,7 @@ static void __exit ucc_uart_exit(void)
 	printk(KERN_INFO
 	       "Freescale QUICC Engine UART device driver unloading\n");
 
-	of_unregister_platform_driver(&ucc_uart_of_driver);
+	platform_driver_unregister(&ucc_uart_of_driver);
 	uart_unregister_driver(&ucc_uart_driver);
 }
 

drivers/tty/sysrq.c

@@ -571,6 +571,7 @@ struct sysrq_state {
 	unsigned int alt_use;
 	bool active;
 	bool need_reinject;
+	bool reinjecting;
 };
 
 static void sysrq_reinject_alt_sysrq(struct work_struct *work)
@@ -581,6 +582,10 @@ static void sysrq_reinject_alt_sysrq(struct work_struct *work)
 	unsigned int alt_code = sysrq->alt_use;
 
 	if (sysrq->need_reinject) {
+		/* we do not want the assignment to be reordered */
+		sysrq->reinjecting = true;
+		mb();
+
 		/* Simulate press and release of Alt + SysRq */
 		input_inject_event(handle, EV_KEY, alt_code, 1);
 		input_inject_event(handle, EV_KEY, KEY_SYSRQ, 1);
@@ -589,6 +594,9 @@ static void sysrq_reinject_alt_sysrq(struct work_struct *work)
 		input_inject_event(handle, EV_KEY, KEY_SYSRQ, 0);
 		input_inject_event(handle, EV_KEY, alt_code, 0);
 		input_inject_event(handle, EV_SYN, SYN_REPORT, 1);
+
+		mb();
+		sysrq->reinjecting = false;
 	}
 }
 
@@ -599,6 +607,13 @@ static bool sysrq_filter(struct input_handle *handle,
 	bool was_active = sysrq->active;
 	bool suppress;
 
+	/*
+	 * Do not filter anything if we are in the process of re-injecting
+	 * Alt+SysRq combination.
+	 */
+	if (sysrq->reinjecting)
+		return false;
+
 	switch (type) {
 
 	case EV_SYN:
@@ -629,7 +644,7 @@ static bool sysrq_filter(struct input_handle *handle,
 				sysrq->alt_use = sysrq->alt;
 				/*
 				 * If nothing else will be pressed we'll need
-				 * to * re-inject Alt-SysRq keysroke.
+				 * to re-inject Alt-SysRq keysroke.
 				 */
 				sysrq->need_reinject = true;
 			}

drivers/tty/tty_audit.c

@@ -95,8 +95,10 @@ static void tty_audit_buf_push(struct task_struct *tsk, uid_t loginuid,
 {
 	if (buf->valid == 0)
 		return;
-	if (audit_enabled == 0)
+	if (audit_enabled == 0) {
+		buf->valid = 0;
 		return;
+	}
 	tty_audit_log("tty", tsk, loginuid, sessionid, buf->major, buf->minor,
 		      buf->data, buf->valid);
 	buf->valid = 0;

drivers/tty/tty_io.c

@@ -90,7 +90,6 @@
 #include <linux/proc_fs.h>
 #include <linux/init.h>
 #include <linux/module.h>
-#include <linux/smp_lock.h>
 #include <linux/device.h>
 #include <linux/wait.h>
 #include <linux/bitops.h>
@@ -2465,12 +2464,12 @@ out:
  *	Locking: none (up to the driver)
  */
 
-static int tty_tiocmget(struct tty_struct *tty, struct file *file, int __user *p)
+static int tty_tiocmget(struct tty_struct *tty, int __user *p)
 {
 	int retval = -EINVAL;
 
 	if (tty->ops->tiocmget) {
-		retval = tty->ops->tiocmget(tty, file);
+		retval = tty->ops->tiocmget(tty);
 
 		if (retval >= 0)
 			retval = put_user(retval, p);
@@ -2481,7 +2480,6 @@ static int tty_tiocmget(struct tty_struct *tty, struct file *file, int __user *p
 /**
  *	tty_tiocmset		-	set modem status
  *	@tty: tty device
- *	@file: user file pointer
  *	@cmd: command - clear bits, set bits or set all
  *	@p: pointer to desired bits
  *
@@ -2491,7 +2489,7 @@ static int tty_tiocmget(struct tty_struct *tty, struct file *file, int __user *p
  *	Locking: none (up to the driver)
  */
 
-static int tty_tiocmset(struct tty_struct *tty, struct file *file, unsigned int cmd,
+static int tty_tiocmset(struct tty_struct *tty, unsigned int cmd,
 	     unsigned __user *p)
 {
 	int retval;
@@ -2518,7 +2516,7 @@ static int tty_tiocmset(struct tty_struct *tty, struct file *file, unsigned int
 	}
 	set &= TIOCM_DTR|TIOCM_RTS|TIOCM_OUT1|TIOCM_OUT2|TIOCM_LOOP;
 	clear &= TIOCM_DTR|TIOCM_RTS|TIOCM_OUT1|TIOCM_OUT2|TIOCM_LOOP;
-	return tty->ops->tiocmset(tty, file, set, clear);
+	return tty->ops->tiocmset(tty, set, clear);
 }
 
 static int tty_tiocgicount(struct tty_struct *tty, void __user *arg)
@@ -2627,6 +2625,11 @@ long tty_ioctl(struct file *file, unsigned int cmd, unsigned long arg)
 		return put_user(tty->ldisc->ops->num, (int __user *)p);
 	case TIOCSETD:
 		return tiocsetd(tty, p);
+	case TIOCVHANGUP:
+		if (!capable(CAP_SYS_ADMIN))
+			return -EPERM;
+		tty_vhangup(tty);
+		return 0;
 	case TIOCGDEV:
 	{
 		unsigned int ret = new_encode_dev(tty_devnum(real_tty));
@@ -2655,11 +2658,11 @@ long tty_ioctl(struct file *file, unsigned int cmd, unsigned long arg)
 		return send_break(tty, arg ? arg*100 : 250);
 
 	case TIOCMGET:
-		return tty_tiocmget(tty, file, p);
+		return tty_tiocmget(tty, p);
 	case TIOCMSET:
 	case TIOCMBIC:
 	case TIOCMBIS:
-		return tty_tiocmset(tty, file, cmd, p);
+		return tty_tiocmset(tty, cmd, p);
 	case TIOCGICOUNT:
 		retval = tty_tiocgicount(tty, p);
 		/* For the moment allow fall through to the old method */
@@ -2677,7 +2680,7 @@ long tty_ioctl(struct file *file, unsigned int cmd, unsigned long arg)
 		break;
 	}
 	if (tty->ops->ioctl) {
-		retval = (tty->ops->ioctl)(tty, file, cmd, arg);
+		retval = (tty->ops->ioctl)(tty, cmd, arg);
 		if (retval != -ENOIOCTLCMD)
 			return retval;
 	}
@@ -2705,7 +2708,7 @@ static long tty_compat_ioctl(struct file *file, unsigned int cmd,
 		return -EINVAL;
 
 	if (tty->ops->compat_ioctl) {
-		retval = (tty->ops->compat_ioctl)(tty, file, cmd, arg);
+		retval = (tty->ops->compat_ioctl)(tty, cmd, arg);
 		if (retval != -ENOIOCTLCMD)
 			return retval;
 	}

drivers/tty/tty_ioctl.c

@@ -486,7 +486,7 @@ int tty_termios_hw_change(struct ktermios *a, struct ktermios *b)
 EXPORT_SYMBOL(tty_termios_hw_change);
 
 /**
- *	change_termios		-	update termios values
+ *	tty_set_termios		-	update termios values
  *	@tty: tty to update
  *	@new_termios: desired new value
  *
@@ -497,7 +497,7 @@ EXPORT_SYMBOL(tty_termios_hw_change);
  *	Locking: termios_mutex
  */
 
-static void change_termios(struct tty_struct *tty, struct ktermios *new_termios)
+int tty_set_termios(struct tty_struct *tty, struct ktermios *new_termios)
 {
 	struct ktermios old_termios;
 	struct tty_ldisc *ld;
@@ -553,7 +553,9 @@ static void change_termios(struct tty_struct *tty, struct ktermios *new_termios)
 		tty_ldisc_deref(ld);
 	}
 	mutex_unlock(&tty->termios_mutex);
+	return 0;
 }
+EXPORT_SYMBOL_GPL(tty_set_termios);
 
 /**
  *	set_termios		-	set termios values for a tty
@@ -562,7 +564,7 @@ static void change_termios(struct tty_struct *tty, struct ktermios *new_termios)
  *	@opt: option information
  *
  *	Helper function to prepare termios data and run necessary other
- *	functions before using change_termios to do the actual changes.
+ *	functions before using tty_set_termios to do the actual changes.
  *
  *	Locking:
  *		Called functions take ldisc and termios_mutex locks
@@ -620,7 +622,7 @@ static int set_termios(struct tty_struct *tty, void __user *arg, int opt)
 			return -EINTR;
 	}
 
-	change_termios(tty, &tmp_termios);
+	tty_set_termios(tty, &tmp_termios);
 
 	/* FIXME: Arguably if tmp_termios == tty->termios AND the
 	   actual requested termios was not tmp_termios then we may
@@ -797,7 +799,7 @@ static int set_sgttyb(struct tty_struct *tty, struct sgttyb __user *sgttyb)
 						termios.c_ospeed);
 #endif
 	mutex_unlock(&tty->termios_mutex);
-	change_termios(tty, &termios);
+	tty_set_termios(tty, &termios);
 	return 0;
 }
 #endif
@@ -951,6 +953,8 @@ int tty_mode_ioctl(struct tty_struct *tty, struct file *file,
 	int ret = 0;
 	struct ktermios kterm;
 
+	BUG_ON(file == NULL);
+
 	if (tty->driver->type == TTY_DRIVER_TYPE_PTY &&
 	    tty->driver->subtype == PTY_TYPE_MASTER)
 		real_tty = tty->link;

drivers/tty/tty_ldisc.c

@@ -34,8 +34,6 @@
 #include <linux/vt_kern.h>
 #include <linux/selection.h>
 
-#include <linux/smp_lock.h>	/* For the moment */
-
 #include <linux/kmod.h>
 #include <linux/nsproxy.h>
 
@@ -534,6 +532,19 @@ static int tty_ldisc_halt(struct tty_struct *tty)
 	return cancel_delayed_work_sync(&tty->buf.work);
 }
 
+/**
+ *	tty_ldisc_flush_works	-	flush all works of a tty
+ *	@tty: tty device to flush works for
+ *
+ *	Sync flush all works belonging to @tty.
+ */
+static void tty_ldisc_flush_works(struct tty_struct *tty)
+{
+	flush_work_sync(&tty->hangup_work);
+	flush_work_sync(&tty->SAK_work);
+	flush_delayed_work_sync(&tty->buf.work);
+}
+
 /**
  *	tty_ldisc_wait_idle	-	wait for the ldisc to become idle
  *	@tty: tty to wait for
@@ -653,7 +664,7 @@ int tty_set_ldisc(struct tty_struct *tty, int ldisc)
 
 	mutex_unlock(&tty->ldisc_mutex);
 
-	flush_scheduled_work();
+	tty_ldisc_flush_works(tty);
 
 	retval = tty_ldisc_wait_idle(tty);
 
@@ -905,7 +916,7 @@ void tty_ldisc_release(struct tty_struct *tty, struct tty_struct *o_tty)
 
 	tty_unlock();
 	tty_ldisc_halt(tty);
-	flush_scheduled_work();
+	tty_ldisc_flush_works(tty);
 	tty_lock();
 
 	mutex_lock(&tty->ldisc_mutex);

drivers/tty/vt/keyboard.c

@@ -654,7 +654,8 @@ static void k_spec(struct vc_data *vc, unsigned char value, char up_flag)
 	if (value >= ARRAY_SIZE(fn_handler))
 		return;
 	if ((kbd->kbdmode == VC_RAW ||
-	     kbd->kbdmode == VC_MEDIUMRAW) &&
+	     kbd->kbdmode == VC_MEDIUMRAW ||
+	     kbd->kbdmode == VC_OFF) &&
 	     value != KVAL(K_SAK))
 		return;		/* SAK is allowed even in raw mode */
 	fn_handler[value](vc);
@@ -1295,7 +1296,7 @@ static void kbd_keycode(unsigned int keycode, int down, int hw_raw)
 	if (rc == NOTIFY_STOP)
 		return;
 
-	if (raw_mode && type != KT_SPEC && type != KT_SHIFT)
+	if ((raw_mode || kbd->kbdmode == VC_OFF) && type != KT_SPEC && type != KT_SHIFT)
 		return;
 
 	(*k_handler[type])(vc, keysym & 0xff, !down);

drivers/tty/vt/selection.c

@@ -26,7 +26,6 @@
 #include <linux/selection.h>
 #include <linux/tiocl.h>
 #include <linux/console.h>
-#include <linux/smp_lock.h>
 
 /* Don't take this from <ctype.h>: 011-015 on the screen aren't spaces */
 #define isspace(c)	((c) == ' ')

drivers/tty/vt/vc_screen.c

@@ -28,13 +28,11 @@
 #include <linux/interrupt.h>
 #include <linux/mm.h>
 #include <linux/init.h>
-#include <linux/mutex.h>
 #include <linux/vt_kern.h>
 #include <linux/selection.h>
 #include <linux/kbd_kern.h>
 #include <linux/console.h>
 #include <linux/device.h>
-#include <linux/smp_lock.h>
 #include <linux/sched.h>
 #include <linux/fs.h>
 #include <linux/poll.h>
@@ -51,6 +49,8 @@
 #undef addr
 #define HEADER_SIZE	4
 
+#define CON_BUF_SIZE (CONFIG_BASE_SMALL ? 256 : PAGE_SIZE)
+
 struct vcs_poll_data {
 	struct notifier_block notifier;
 	unsigned int cons_num;
@@ -131,21 +131,45 @@ vcs_poll_data_get(struct file *file)
 	return poll;
 }
 
+/*
+ * Returns VC for inode.
+ * Must be called with console_lock.
+ */
+static struct vc_data*
+vcs_vc(struct inode *inode, int *viewed)
+{
+	unsigned int currcons = iminor(inode) & 127;
+
+	WARN_CONSOLE_UNLOCKED();
+
+	if (currcons == 0) {
+		currcons = fg_console;
+		if (viewed)
+			*viewed = 1;
+	} else {
+		currcons--;
+		if (viewed)
+			*viewed = 0;
+	}
+	return vc_cons[currcons].d;
+}
+
+/*
+ * Returns size for VC carried by inode.
+ * Must be called with console_lock.
+ */
 static int
 vcs_size(struct inode *inode)
 {
 	int size;
 	int minor = iminor(inode);
-	int currcons = minor & 127;
 	struct vc_data *vc;
 
-	if (currcons == 0)
-		currcons = fg_console;
-	else
-		currcons--;
-	if (!vc_cons_allocated(currcons))
+	WARN_CONSOLE_UNLOCKED();
+
+	vc = vcs_vc(inode, NULL);
+	if (!vc)
 		return -ENXIO;
-	vc = vc_cons[currcons].d;
 
 	size = vc->vc_rows * vc->vc_cols;
 
@@ -158,11 +182,13 @@ static loff_t vcs_lseek(struct file *file, loff_t offset, int orig)
 {
 	int size;
 
-	mutex_lock(&con_buf_mtx);
+	console_lock();
 	size = vcs_size(file->f_path.dentry->d_inode);
+	console_unlock();
+	if (size < 0)
+		return size;
 	switch (orig) {
 		default:
-			mutex_unlock(&con_buf_mtx);
 			return -EINVAL;
 		case 2:
 			offset += size;
@@ -173,11 +199,9 @@ static loff_t vcs_lseek(struct file *file, loff_t offset, int orig)
 			break;
 	}
 	if (offset < 0 || offset > size) {
-		mutex_unlock(&con_buf_mtx);
 		return -EINVAL;
 	}
 	file->f_pos = offset;
-	mutex_unlock(&con_buf_mtx);
 	return file->f_pos;
 }
 
@@ -190,12 +214,15 @@ vcs_read(struct file *file, char __user *buf, size_t count, loff_t *ppos)
 	struct vc_data *vc;
 	struct vcs_poll_data *poll;
 	long pos;
-	long viewed, attr, read;
-	int col, maxcol;
+	long attr, read;
+	int col, maxcol, viewed;
 	unsigned short *org = NULL;
 	ssize_t ret;
+	char *con_buf;
 
-	mutex_lock(&con_buf_mtx);
+	con_buf = (char *) __get_free_page(GFP_KERNEL);
+	if (!con_buf)
+		return -ENOMEM;
 
 	pos = *ppos;
 
@@ -205,18 +232,10 @@ vcs_read(struct file *file, char __user *buf, size_t count, loff_t *ppos)
 	console_lock();
 
 	attr = (currcons & 128);
-	currcons = (currcons & 127);
-	if (currcons == 0) {
-		currcons = fg_console;
-		viewed = 1;
-	} else {
-		currcons--;
-		viewed = 0;
-	}
 	ret = -ENXIO;
-	if (!vc_cons_allocated(currcons))
+	vc = vcs_vc(inode, &viewed);
+	if (!vc)
 		goto unlock_out;
-	vc = vc_cons[currcons].d;
 
 	ret = -EINVAL;
 	if (pos < 0)
@@ -237,6 +256,12 @@ vcs_read(struct file *file, char __user *buf, size_t count, loff_t *ppos)
 		 * could sleep.
 		 */
 		size = vcs_size(inode);
+		if (size < 0) {
+			if (read)
+				break;
+			ret = size;
+			goto unlock_out;
+		}
 		if (pos >= size)
 			break;
 		if (count > size - pos)
@@ -355,7 +380,7 @@ vcs_read(struct file *file, char __user *buf, size_t count, loff_t *ppos)
 		ret = read;
 unlock_out:
 	console_unlock();
-	mutex_unlock(&con_buf_mtx);
+	free_page((unsigned long) con_buf);
 	return ret;
 }
 
@@ -366,13 +391,16 @@ vcs_write(struct file *file, const char __user *buf, size_t count, loff_t *ppos)
 	unsigned int currcons = iminor(inode);
 	struct vc_data *vc;
 	long pos;
-	long viewed, attr, size, written;
+	long attr, size, written;
 	char *con_buf0;
-	int col, maxcol;
+	int col, maxcol, viewed;
 	u16 *org0 = NULL, *org = NULL;
 	size_t ret;
+	char *con_buf;
 
-	mutex_lock(&con_buf_mtx);
+	con_buf = (char *) __get_free_page(GFP_KERNEL);
+	if (!con_buf)
+		return -ENOMEM;
 
 	pos = *ppos;
 
@@ -382,19 +410,10 @@ vcs_write(struct file *file, const char __user *buf, size_t count, loff_t *ppos)
 	console_lock();
 
 	attr = (currcons & 128);
-	currcons = (currcons & 127);
-
-	if (currcons == 0) {
-		currcons = fg_console;
-		viewed = 1;
-	} else {
-		currcons--;
-		viewed = 0;
-	}
 	ret = -ENXIO;
-	if (!vc_cons_allocated(currcons))
+	vc = vcs_vc(inode, &viewed);
+	if (!vc)
 		goto unlock_out;
-	vc = vc_cons[currcons].d;
 
 	size = vcs_size(inode);
 	ret = -EINVAL;
@@ -436,6 +455,12 @@ vcs_write(struct file *file, const char __user *buf, size_t count, loff_t *ppos)
 		 * Return data written up to now on failure.
 		 */
 		size = vcs_size(inode);
+		if (size < 0) {
+			if (written)
+				break;
+			ret = size;
+			goto unlock_out;
+		}
 		if (pos >= size)
 			break;
 		if (this_round > size - pos)
@@ -543,9 +568,7 @@ vcs_write(struct file *file, const char __user *buf, size_t count, loff_t *ppos)
 
 unlock_out:
 	console_unlock();
-
-	mutex_unlock(&con_buf_mtx);
-
+	free_page((unsigned long) con_buf);
 	return ret;
 }
 

drivers/tty/vt/vt.c

@@ -89,7 +89,6 @@
 #include <linux/mutex.h>
 #include <linux/vt_kern.h>
 #include <linux/selection.h>
-#include <linux/smp_lock.h>
 #include <linux/tiocl.h>
 #include <linux/kbd_kern.h>
 #include <linux/consolemap.h>
@@ -2068,18 +2067,6 @@ static void do_con_trol(struct tty_struct *tty, struct vc_data *vc, int c)
 	}
 }
 
-/* This is a temporary buffer used to prepare a tty console write
- * so that we can easily avoid touching user space while holding the
- * console spinlock.  It is allocated in con_init and is shared by
- * this code and the vc_screen read/write tty calls.
- *
- * We have to allocate this statically in the kernel data section
- * since console_init (and thus con_init) are called before any
- * kernel memory allocation is available.
- */
-char con_buf[CON_BUF_SIZE];
-DEFINE_MUTEX(con_buf_mtx);
-
 /* is_double_width() is based on the wcwidth() implementation by
  * Markus Kuhn -- 2007-05-26 (Unicode 5.0)
  * Latest version: http://www.cl.cam.ac.uk/~mgk25/ucs/wcwidth.c
@@ -2157,10 +2144,10 @@ static int do_con_write(struct tty_struct *tty, const unsigned char *buf, int co
 
 	currcons = vc->vc_num;
 	if (!vc_cons_allocated(currcons)) {
-	    /* could this happen? */
-		printk_once("con_write: tty %d not allocated\n", currcons+1);
-	    console_unlock();
-	    return 0;
+		/* could this happen? */
+		pr_warn_once("con_write: tty %d not allocated\n", currcons+1);
+		console_unlock();
+		return 0;
 	}
 
 	himask = vc->vc_hi_font_mask;
@@ -2940,7 +2927,7 @@ static int __init con_init(void)
 	gotoxy(vc, vc->vc_x, vc->vc_y);
 	csi_J(vc, 0);
 	update_screen(vc);
-	printk("Console: %s %s %dx%d",
+	pr_info("Console: %s %s %dx%d",
 		vc->vc_can_do_color ? "colour" : "mono",
 		display_desc, vc->vc_cols, vc->vc_rows);
 	printable = 1;
@@ -3103,7 +3090,7 @@ static int bind_con_driver(const struct consw *csw, int first, int last,
 			clear_buffer_attributes(vc);
 	}
 
-	printk("Console: switching ");
+	pr_info("Console: switching ");
 	if (!deflt)
 		printk("consoles %d-%d ", first+1, last+1);
 	if (j >= 0) {
@@ -3809,7 +3796,8 @@ void do_unblank_screen(int leaving_gfx)
 		return;
 	if (!vc_cons_allocated(fg_console)) {
 		/* impossible */
-		printk("unblank_screen: tty %d not allocated ??\n", fg_console+1);
+		pr_warning("unblank_screen: tty %d not allocated ??\n",
+			   fg_console+1);
 		return;
 	}
 	vc = vc_cons[fg_console].d;

drivers/tty/vt/vt_ioctl.c

@@ -27,7 +27,6 @@
 #include <linux/console.h>
 #include <linux/consolemap.h>
 #include <linux/signal.h>
-#include <linux/smp_lock.h>
 #include <linux/timex.h>
 
 #include <asm/io.h>
@@ -495,7 +494,7 @@ do_unimap_ioctl(int cmd, struct unimapdesc __user *user_ud, int perm, struct vc_
  * We handle the console-specific ioctl's here.  We allow the
  * capability to modify any console, not just the fg_console. 
  */
-int vt_ioctl(struct tty_struct *tty, struct file * file,
+int vt_ioctl(struct tty_struct *tty,
 	     unsigned int cmd, unsigned long arg)
 {
 	struct vc_data *vc = tty->driver_data;
@@ -688,6 +687,9 @@ int vt_ioctl(struct tty_struct *tty, struct file * file,
 			kbd->kbdmode = VC_UNICODE;
 			compute_shiftstate();
 			break;
+		  case K_OFF:
+			kbd->kbdmode = VC_OFF;
+			break;
 		  default:
 			ret = -EINVAL;
 			goto out;
@@ -1007,8 +1009,9 @@ int vt_ioctl(struct tty_struct *tty, struct file * file,
 			if (ret)
 				break;
 			/* Commence switch and lock */
-			set_console(arg);
+			set_console(vsa.console);
 		}
+		break;
 	}
 
 	/*
@@ -1491,7 +1494,7 @@ compat_unimap_ioctl(unsigned int cmd, struct compat_unimapdesc __user *user_ud,
 	return 0;
 }
 
-long vt_compat_ioctl(struct tty_struct *tty, struct file * file,
+long vt_compat_ioctl(struct tty_struct *tty,
 	     unsigned int cmd, unsigned long arg)
 {
 	struct vc_data *vc = tty->driver_data;
@@ -1577,7 +1580,7 @@ out:
 
 fallback:
 	tty_unlock();
-	return vt_ioctl(tty, file, cmd, arg);
+	return vt_ioctl(tty, cmd, arg);
 }