This is the bulk of GPIO changes for the v4.21 kernel series:

Core changes:
 
 - Some core changes are already in outside of this pull
   request as they came through the regulator tree, most
   notably devm_gpiod_unhinge() that removes devres refcount
   management from a GPIO descriptor. This is needed in
   subsystems such as regulators where the regulator core
   need to take over the reference counting and lifecycle
   management for a GPIO descriptor.
 
 - We dropped devm_gpiochip_remove() and devm_gpio_chip_match()
   as nothing needs it. We can bring it back if need be.
 
 - Add a global TODO so people see where we are going. This
   helps setting the direction now that we are two GPIO
   maintainers.
 
 - Handle the MMC CD/WP properties in the device tree core.
   (The bulk of patches activating this code is already
   merged through the MMC/SD tree.)
 
 - Augment gpiochip_request_own_desc() to pass a flag so
   we as gpiochips can request lines as active low or open
   drain etc even from ourselves.
 
 New drivers:
 
 - New driver for Cadence GPIO blocks.
 
 - New driver for Atmel SAMA5D2 PIOBU GPIO lines.
 
 Driver improvements:
 
 - A major refactoring of the PCA953x driver - this driver has
   been around for ages, and is now modernized to reduce code
   duplication that has stacked up and is using regmap to read
   write and cache registers.
 
 - Intel drivers are now maintained in a separate tree and
   start with a round of cleanups and unifications.
 -----BEGIN PGP SIGNATURE-----
 
 iQIcBAABAgAGBQJcJJcmAAoJEEEQszewGV1zdCoQAMSLPh+4QdYLFS3ZmnsPvZkg
 Zkz94RVT+uLLmHpR8XBl0wl4mmYCiwB50IwsXwlvJGceSXjCn6hLg9BZBP5hFMCb
 yFk3fgXQSh7TOnpjgbCWSssCjpejQ0cOb/2nWHz5s/fbYKYlh3VXckW9hhW+R+b3
 6+Mno1SzmBkpVVQ21ISlZeLoNDynkCW6DfjiKMuHAyxzxa0oZ9Qid+tnVDnQM4rD
 rCnvYLuvxlXw97W+LI7AU9KoCITdO+2M/0dtGVEEYKfHseRReSy2Oo3nlqCglygX
 cNkBe9RYU1CJdas1P/c18wjDAqWp/pbugzHDkYF5Y3tBtB2rQSftjtnQngiVMXMt
 De7ejPvL7/OLECvI2WUD6y9NAduw/HE4FO8BBdn0gP/a9svJpVZ993yPd3F9n7EZ
 ZIBpycDZVtkcE7dwQgek17bFILRY5nBBMB9oCLL2wk48qdmjpcAbxVfGSsYOe6wO
 +cZRZuj/eR3i9gHRugfFx7Evoc7l4erihTpES/YAy3De1s3uV8KjT4zE7Jh+M9LW
 GM797BcXJJeb5toC7HZ/G2UAVMyWEhY0n7PGG616CS8IrzmzIZpJOL9kUVOWPb0F
 9CPt6qhVbUl9rxp1H/Z3TxvYqIw6icn/z5YewZxLU1zaBlpE3jc7PhZb5hOGnFUf
 /DWwe4n99JsjHTrGx1ra
 =05LW
 -----END PGP SIGNATURE-----

Merge tag 'gpio-v4.21-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio

Pull GPIO updates from Linus Walleij:
 "This is the bulk of GPIO changes for the v4.21 kernel series.

  Core changes:

   - Some core changes are already in outside of this pull request as
     they came through the regulator tree, most notably
     devm_gpiod_unhinge() that removes devres refcount management from a
     GPIO descriptor. This is needed in subsystems such as regulators
     where the regulator core need to take over the reference counting
     and lifecycle management for a GPIO descriptor.

   - We dropped devm_gpiochip_remove() and devm_gpio_chip_match() as
     nothing needs it. We can bring it back if need be.

   - Add a global TODO so people see where we are going. This helps
     setting the direction now that we are two GPIO maintainers.

   - Handle the MMC CD/WP properties in the device tree core. (The bulk
     of patches activating this code is already merged through the
     MMC/SD tree.)

   - Augment gpiochip_request_own_desc() to pass a flag so we as
     gpiochips can request lines as active low or open drain etc even
     from ourselves.

  New drivers:

   - New driver for Cadence GPIO blocks.

   - New driver for Atmel SAMA5D2 PIOBU GPIO lines.

  Driver improvements:

   - A major refactoring of the PCA953x driver - this driver has been
     around for ages, and is now modernized to reduce code duplication
     that has stacked up and is using regmap to read write and cache
     registers.

   - Intel drivers are now maintained in a separate tree and start with
     a round of cleanups and unifications"

* tag 'gpio-v4.21-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (99 commits)
  gpio: sama5d2-piobu: Depend on OF_GPIO
  gpio: Add Cadence GPIO driver
  dt-bindings: gpio: Add bindings for Cadence GPIO
  gpiolib-acpi: remove unused variable 'err', cleans up build warning
  gpio: mxs: read pin level directly instead of using .get
  gpio: aspeed: remove duplicated statement
  gpio: add driver for SAMA5D2 PIOBU pins
  dt-bindings: arm: atmel: describe SECUMOD usage as a GPIO controller
  gpio/mmc/of: Respect polarity in the device tree
  dt-bindings: gpio: rcar: Add r8a774c0 (RZ/G2E) support
  memory: omap-gpmc: Get the header of the enum
  ARM: omap1: Fix new user of gpiochip_request_own_desc()
  gpio: pca953x: Add regmap dependency for PCA953x driver
  gpio: raspberrypi-exp: decrease refcount on firmware dt node
  gpiolib: Fix return value of gpio_to_desc() stub if !GPIOLIB
  gpio: pca953x: Restore registers after suspend/resume cycle
  gpio: pca953x: Zap single use of pca953x_read_single()
  gpio: pca953x: Zap ad-hoc reg_output cache
  gpio: pca953x: Zap ad-hoc reg_direction cache
  gpio: pca953x: Perform basic regmap conversion
  ...

Documentation/devicetree/bindings/arm/atmel-sysregs.txt

@@ -158,14 +158,24 @@ Security Module (SECUMOD)
 
 The Security Module macrocell provides all necessary secure functions to avoid
 voltage, temperature, frequency and mechanical attacks on the chip. It also
-embeds secure memories that can be scrambled
+embeds secure memories that can be scrambled.
+
+The Security Module also offers the PIOBU pins which can be used as GPIO pins.
+Note that they maintain their voltage during Backup/Self-refresh.
 
 required properties:
 - compatible: Should be "atmel,<chip>-secumod", "syscon".
   <chip> can be "sama5d2".
 - reg: Should contain registers location and length
+- gpio-controller:	Marks the port as GPIO controller.
+- #gpio-cells:		There are 2. The pin number is the
+			first, the second represents additional
+			parameters such as GPIO_ACTIVE_HIGH/LOW.
+
 
 	secumod@fc040000 {
 		compatible = "atmel,sama5d2-secumod", "syscon";
 		reg = <0xfc040000 0x100>;
+		gpio-controller;
+		#gpio-cells = <2>;
 	};

Documentation/devicetree/bindings/gpio/cdns,gpio.txt

@@ -0,0 +1,43 @@
+Cadence GPIO controller bindings
+
+Required properties:
+- compatible: should be "cdns,gpio-r1p02".
+- reg: the register base address and size.
+- #gpio-cells: should be 2.
+	* first cell is the GPIO number.
+	* second cell specifies the GPIO flags, as defined in
+		<dt-bindings/gpio/gpio.h>. Only the GPIO_ACTIVE_HIGH
+		and GPIO_ACTIVE_LOW flags are supported.
+- gpio-controller: marks the device as a GPIO controller.
+- clocks: should contain one entry referencing the peripheral clock driving
+	the GPIO controller.
+
+Optional properties:
+- ngpios: integer number of gpio lines supported by this controller, up to 32.
+- interrupts: interrupt specifier for the controllers interrupt.
+- interrupt-controller: marks the device as an interrupt controller. When
+	defined, interrupts, interrupt-parent and #interrupt-cells
+	are required.
+- interrupt-cells: should be 2.
+	* first cell is the GPIO number you want to use as an IRQ source.
+	* second cell specifies the IRQ type, as defined in
+		<dt-bindings/interrupt-controller/irq.h>.
+		Currently only level sensitive IRQs are supported.
+
+
+Example:
+	gpio0: gpio-controller@fd060000 {
+		compatible = "cdns,gpio-r1p02";
+		reg =<0xfd060000 0x1000>;
+
+		clocks = <&gpio_clk>;
+
+		interrupt-parent = <&gic>;
+		interrupts = <0 5 IRQ_TYPE_LEVEL_HIGH>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};

Documentation/devicetree/bindings/gpio/gpio-vf610.txt

@@ -24,6 +24,12 @@ Required properties for GPIO node:
       4 = active high level-sensitive.
       8 = active low level-sensitive.
 
+Optional properties:
+-clocks:	Must contain an entry for each entry in clock-names.
+		See common clock-bindings.txt for details.
+-clock-names:	A list of clock names. For imx7ulp, it must contain
+		"gpio", "port".
+
 Note: Each GPIO port should have an alias correctly numbered in "aliases"
 node.
 

Documentation/devicetree/bindings/gpio/nxp,lpc1850-gpio.txt

@@ -3,12 +3,24 @@ NXP LPC18xx/43xx GPIO controller Device Tree Bindings
 
 Required properties:
 - compatible		: Should be "nxp,lpc1850-gpio"
-- reg			: Address and length of the register set for the device
-- clocks		: Clock specifier (see clock bindings for details)
-- gpio-controller	: Marks the device node as a GPIO controller.
-- #gpio-cells 		: Should be two
-			  - First cell is the GPIO line number
-			  - Second cell is used to specify polarity
+- reg			: List of addresses and lengths of the GPIO controller
+			  register sets
+- reg-names		: Should be "gpio", "gpio-pin-ic", "gpio-group0-ic" and
+			  "gpio-gpoup1-ic"
+- clocks		: Phandle and clock specifier pair for GPIO controller
+- resets		: Phandle and reset specifier pair for GPIO controller
+- gpio-controller	: Marks the device node as a GPIO controller
+- #gpio-cells 		: Should be two:
+			  - The first cell is the GPIO line number
+			  - The second cell is used to specify polarity
+- interrupt-controller	: Marks the device node as an interrupt controller
+- #interrupt-cells	: Should be two:
+			  - The first cell is an interrupt number within
+			    0..9 range, for GPIO pin interrupts it is equal
+			    to 'nxp,gpio-pin-interrupt' property value of
+			    GPIO pin configuration, 8 is for GPIO GROUP0
+			    interrupt, 9 is for GPIO GROUP1 interrupt
+			  - The second cell is used to specify interrupt type
 
 Optional properties:
 - gpio-ranges		: Mapping between GPIO and pinctrl
@@ -19,21 +31,29 @@ Example:
 
 gpio: gpio@400f4000 {
 	compatible = "nxp,lpc1850-gpio";
-	reg = <0x400f4000 0x4000>;
+	reg = <0x400f4000 0x4000>, <0x40087000 0x1000>,
+	      <0x40088000 0x1000>, <0x40089000 0x1000>;
+	reg-names = "gpio", "gpio-pin-ic",
+		    "gpio-group0-ic", "gpio-gpoup1-ic";
 	clocks = <&ccu1 CLK_CPU_GPIO>;
+	resets = <&rgu 28>;
 	gpio-controller;
 	#gpio-cells = <2>;
+	interrupt-controller;
+	#interrupt-cells = <2>;
 	gpio-ranges =	<&pinctrl LPC_GPIO(0,0)  LPC_PIN(0,0)  2>,
 			...
 			<&pinctrl LPC_GPIO(7,19) LPC_PIN(f,5)  7>;
 };
 
 gpio_joystick {
-	compatible = "gpio-keys-polled";
+	compatible = "gpio-keys";
 	...
 
-	button@0 {
+	button0 {
 		...
+		interrupt-parent = <&gpio>;
+		interrupts = <1 IRQ_TYPE_EDGE_BOTH>;
 		gpios = <&gpio LPC_GPIO(4,8) GPIO_ACTIVE_LOW>;
 	};
 };

Documentation/devicetree/bindings/gpio/renesas,gpio-rcar.txt

@@ -8,6 +8,7 @@ Required Properties:
     - "renesas,gpio-r8a7745": for R8A7745 (RZ/G1E) compatible GPIO controller.
     - "renesas,gpio-r8a77470": for R8A77470 (RZ/G1C) compatible GPIO controller.
     - "renesas,gpio-r8a774a1": for R8A774A1 (RZ/G2M) compatible GPIO controller.
+    - "renesas,gpio-r8a774c0": for R8A774C0 (RZ/G2E) compatible GPIO controller.
     - "renesas,gpio-r8a7778": for R8A7778 (R-Car M1) compatible GPIO controller.
     - "renesas,gpio-r8a7779": for R8A7779 (R-Car H1) compatible GPIO controller.
     - "renesas,gpio-r8a7790": for R8A7790 (R-Car H2) compatible GPIO controller.

Documentation/devicetree/bindings/gpio/snps-dwapb-gpio.txt

@@ -43,7 +43,7 @@ gpio: gpio@20000 {
 	#address-cells = <1>;
 	#size-cells = <0>;
 
-	porta: gpio-controller@0 {
+	porta: gpio@0 {
 		compatible = "snps,dw-apb-gpio-port";
 		gpio-controller;
 		#gpio-cells = <2>;
@@ -55,7 +55,7 @@ gpio: gpio@20000 {
 		interrupts = <0>;
 	};
 
-	portb: gpio-controller@1 {
+	portb: gpio@1 {
 		compatible = "snps,dw-apb-gpio-port";
 		gpio-controller;
 		#gpio-cells = <2>;