Merge branch 'for-linus' of git://git.infradead.org/users/vkoul/slave-dma

Pull slave-dmaengine updates from Vinod Koul:
 - New driver for Qcom bam dma
 - New driver for RCAR peri-peri
 - New driver for FSL eDMA
 - Various odd fixes and updates thru the subsystem

* 'for-linus' of git://git.infradead.org/users/vkoul/slave-dma: (29 commits)
  dmaengine: add Qualcomm BAM dma driver
  shdma: add R-Car Audio DMAC peri peri driver
  dmaengine: sirf: enable generic dt binding for dma channels
  dma: omap-dma: Implement device_slave_caps callback
  dmaengine: qcom_bam_dma: Add device tree binding
  dma: dw: Add suspend and resume handling for PCI mode DW_DMAC.
  dma: dw: allocate memory in two stages in probe
  Add new line to test result strings produced in verbose mode
  dmaengine: pch_dma: use tasklet_kill in teardown
  dmaengine: at_hdmac: use tasklet_kill in teardown
  dma: cppi41: start tear down only if channel is busy
  usb: musb: musb_cppi41: Dont reprogram DMA if tear down is initiated
  dmaengine: s3c24xx-dma: make phy->irq signed for error handling
  dma: imx-dma: Add missing module owner field
  dma: imx-dma: Replace printk with dev_*
  dma: fsl-edma: fix static checker warning of NULL dereference
  dma: Remove comment about embedding dma_slave_config into custom structs
  dma: mmp_tdma: move to generic device tree binding
  dma: mmp_pdma: add IRQF_SHARED when request irq
  dma: edma: Fix memory leak in edma_prep_dma_cyclic()
  ...

Documentation/devicetree/bindings/dma/fsl-edma.txt

@@ -0,0 +1,76 @@
+* Freescale enhanced Direct Memory Access(eDMA) Controller
+
+  The eDMA channels have multiplex capability by programmble memory-mapped
+registers. channels are split into two groups, called DMAMUX0 and DMAMUX1,
+specific DMA request source can only be multiplexed by any channel of certain
+group, DMAMUX0 or DMAMUX1, but not both.
+
+* eDMA Controller
+Required properties:
+- compatible :
+	- "fsl,vf610-edma" for eDMA used similar to that on Vybrid vf610 SoC
+- reg : Specifies base physical address(s) and size of the eDMA registers.
+	The 1st region is eDMA control register's address and size.
+	The 2nd and the 3rd regions are programmable channel multiplexing
+	control register's address and size.
+- interrupts : A list of interrupt-specifiers, one for each entry in
+	interrupt-names.
+- interrupt-names : Should contain:
+	"edma-tx" - the transmission interrupt
+	"edma-err" - the error interrupt
+- #dma-cells : Must be <2>.
+	The 1st cell specifies the DMAMUX(0 for DMAMUX0 and 1 for DMAMUX1).
+	Specific request source can only be multiplexed by specific channels
+	group called DMAMUX.
+	The 2nd cell specifies the request source(slot) ID.
+	See the SoC's reference manual for all the supported request sources.
+- dma-channels : Number of channels supported by the controller
+- clock-names : A list of channel group clock names. Should contain:
+	"dmamux0" - clock name of mux0 group
+	"dmamux1" - clock name of mux1 group
+- clocks : A list of phandle and clock-specifier pairs, one for each entry in
+	clock-names.
+
+Optional properties:
+- big-endian: If present registers and hardware scatter/gather descriptors
+	of the eDMA are implemented in big endian mode, otherwise in little
+	mode.
+
+
+Examples:
+
+edma0: dma-controller@40018000 {
+	#dma-cells = <2>;
+	compatible = "fsl,vf610-edma";
+	reg = <0x40018000 0x2000>,
+		<0x40024000 0x1000>,
+		<0x40025000 0x1000>;
+	interrupts = <0 8 IRQ_TYPE_LEVEL_HIGH>,
+		<0 9 IRQ_TYPE_LEVEL_HIGH>;
+	interrupt-names = "edma-tx", "edma-err";
+	dma-channels = <32>;
+	clock-names = "dmamux0", "dmamux1";
+	clocks = <&clks VF610_CLK_DMAMUX0>,
+		<&clks VF610_CLK_DMAMUX1>;
+};
+
+
+* DMA clients
+DMA client drivers that uses the DMA function must use the format described
+in the dma.txt file, using a two-cell specifier for each channel: the 1st
+specifies the channel group(DMAMUX) in which this request can be multiplexed,
+and the 2nd specifies the request source.
+
+Examples:
+
+sai2: sai@40031000 {
+	compatible = "fsl,vf610-sai";
+	reg = <0x40031000 0x1000>;
+	interrupts = <0 86 IRQ_TYPE_LEVEL_HIGH>;
+	clock-names = "sai";
+	clocks = <&clks VF610_CLK_SAI2>;
+	dma-names = "tx", "rx";
+	dmas = <&edma0 0 21>,
+		<&edma0 0 20>;
+	status = "disabled";
+};

Documentation/devicetree/bindings/dma/qcom_bam_dma.txt

@@ -0,0 +1,41 @@
+QCOM BAM DMA controller
+
+Required properties:
+- compatible: must contain "qcom,bam-v1.4.0" for MSM8974
+- reg: Address range for DMA registers
+- interrupts: Should contain the one interrupt shared by all channels
+- #dma-cells: must be <1>, the cell in the dmas property of the client device
+  represents the channel number
+- clocks: required clock
+- clock-names: must contain "bam_clk" entry
+- qcom,ee : indicates the active Execution Environment identifier (0-7) used in
+  the secure world.
+
+Example:
+
+	uart-bam: dma@f9984000 = {
+		compatible = "qcom,bam-v1.4.0";
+		reg = <0xf9984000 0x15000>;
+		interrupts = <0 94 0>;
+		clocks = <&gcc GCC_BAM_DMA_AHB_CLK>;
+		clock-names = "bam_clk";
+		#dma-cells = <1>;
+		qcom,ee = <0>;
+	};
+
+DMA clients must use the format described in the dma.txt file, using a two cell
+specifier for each channel.
+
+Example:
+	serial@f991e000 {
+		compatible = "qcom,msm-uart";
+		reg = <0xf991e000 0x1000>
+			<0xf9944000 0x19000>;
+		interrupts = <0 108 0>;
+		clocks = <&gcc GCC_BLSP1_UART2_APPS_CLK>,
+			<&gcc GCC_BLSP1_AHB_CLK>;
+		clock-names = "core", "iface";
+
+		dmas = <&uart-bam 0>, <&uart-bam 1>;
+		dma-names = "rx", "tx";
+	};

Documentation/devicetree/bindings/dma/sirfsoc-dma.txt

@@ -0,0 +1,43 @@
+* CSR SiRFSoC DMA controller
+
+See dma.txt first
+
+Required properties:
+- compatible: Should be "sirf,prima2-dmac" or "sirf,marco-dmac"
+- reg: Should contain DMA registers location and length.
+- interrupts: Should contain one interrupt shared by all channel
+- #dma-cells: must be <1>. used to represent the number of integer
+    cells in the dmas property of client device.
+- clocks: clock required
+
+Example:
+
+Controller:
+dmac0: dma-controller@b00b0000 {
+	compatible = "sirf,prima2-dmac";
+	reg = <0xb00b0000 0x10000>;
+	interrupts = <12>;
+	clocks = <&clks 24>;
+	#dma-cells = <1>;
+};
+
+
+Client:
+Fill the specific dma request line in dmas. In the below example, spi0 read
+channel request line is 9 of the 2nd dma controller, while write channel uses
+4 of the 2nd dma controller; spi1 read channel request line is 12 of the 1st
+dma controller, while write channel uses 13 of the 1st dma controller:
+
+spi0: spi@b00d0000 {
+	compatible = "sirf,prima2-spi";
+	dmas = <&dmac1 9>,
+		<&dmac1 4>;
+	dma-names = "rx", "tx";
+};
+
+spi1: spi@b0170000 {
+	compatible = "sirf,prima2-spi";
+	dmas = <&dmac0 12>,
+		<&dmac0 13>;
+	dma-names = "rx", "tx";
+};