Merge git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux

The merge is merely to fix conflicts before sending a pull request.

Conflicts:
	drivers/power/ab8500_btemp.c
	drivers/power/ab8500_charger.c
	drivers/power/ab8500_fg.c
	drivers/power/abx500_chargalg.c
	drivers/power/max8925_power.c

Signed-off-by: Anton Vorontsov <[email protected]>

Documentation/devicetree/bindings/arm/atmel-at91.txt

@@ -7,6 +7,12 @@ PIT Timer required properties:
 - interrupts: Should contain interrupt for the PIT which is the IRQ line
   shared across all System Controller members.
 
+System Timer (ST) required properties:
+- compatible: Should be "atmel,at91rm9200-st"
+- reg: Should contain registers location and length
+- interrupts: Should contain interrupt for the ST which is the IRQ line
+  shared across all System Controller members.
+
 TC/TCLIB Timer required properties:
 - compatible: Should be "atmel,<chip>-tcb".
   <chip> can be "at91rm9200" or "at91sam9x5"

Documentation/devicetree/bindings/arm/davinci/nand.txt

@@ -23,29 +23,16 @@ Recommended properties :
 - ti,davinci-nand-buswidth: buswidth 8 or 16
 - ti,davinci-nand-use-bbt: use flash based bad block table support.
 
-Example (enbw_cmc board):
-aemif@60000000 {
-	compatible = "ti,davinci-aemif";
-	#address-cells = <2>;
-	#size-cells = <1>;
-	reg = <0x68000000 0x80000>;
-	ranges = <2 0 0x60000000 0x02000000
-		  3 0 0x62000000 0x02000000
-		  4 0 0x64000000 0x02000000
-		  5 0 0x66000000 0x02000000
-		  6 0 0x68000000 0x02000000>;
-	nand@3,0 {
-		compatible = "ti,davinci-nand";
-		reg = <3 0x0 0x807ff
-			6 0x0 0x8000>;
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ti,davinci-chipselect = <1>;
-		ti,davinci-mask-ale = <0>;
-		ti,davinci-mask-cle = <0>;
-		ti,davinci-mask-chipsel = <0>;
-		ti,davinci-ecc-mode = "hw";
-		ti,davinci-ecc-bits = <4>;
-		ti,davinci-nand-use-bbt;
-	};
+Example(da850 EVM ):
+nand_cs3@62000000 {
+	compatible = "ti,davinci-nand";
+	reg = <0x62000000 0x807ff
+		0x68000000 0x8000>;
+	ti,davinci-chipselect = <1>;
+	ti,davinci-mask-ale = <0>;
+	ti,davinci-mask-cle = <0>;
+	ti,davinci-mask-chipsel = <0>;
+	ti,davinci-ecc-mode = "hw";
+	ti,davinci-ecc-bits = <4>;
+	ti,davinci-nand-use-bbt;
 };

Documentation/devicetree/bindings/arm/l2cc.txt

@@ -37,7 +37,7 @@ L2: cache-controller {
         reg = <0xfff12000 0x1000>;
         arm,data-latency = <1 1 1>;
         arm,tag-latency = <2 2 2>;
-        arm,filter-latency = <0x80000000 0x8000000>;
+        arm,filter-ranges = <0x80000000 0x8000000>;
         cache-unified;
         cache-level = <2>;
 	interrupts = <45>;

Documentation/devicetree/bindings/clock/imx23-clock.txt

@@ -52,7 +52,7 @@ clocks and IDs.
 	lcdif		38
 	etm		39
 	usb		40
-	usb_pwr		41
+	usb_phy		41
 
 Examples:
 

Documentation/devicetree/bindings/clock/imx28-clock.txt

@@ -73,8 +73,8 @@ clocks and IDs.
 	can1		59
 	usb0		60
 	usb1		61
-	usb0_pwr	62
-	usb1_pwr	63
+	usb0_phy	62
+	usb1_phy	63
 	enet_out	64
 
 Examples:

Documentation/devicetree/bindings/cpufreq/cpufreq-spear.txt

@@ -0,0 +1,42 @@
+SPEAr cpufreq driver
+-------------------
+
+SPEAr SoC cpufreq driver for CPU frequency scaling.
+It supports both uniprocessor (UP) and symmetric multiprocessor (SMP) systems
+which share clock across all CPUs.
+
+Required properties:
+- cpufreq_tbl: Table of frequencies CPU could be transitioned into, in the
+  increasing order.
+
+Optional properties:
+- clock-latency: Specify the possible maximum transition latency for clock, in
+  unit of nanoseconds.
+
+Both required and optional properties listed above must be defined under node
+/cpus/cpu@0.
+
+Examples:
+--------
+cpus {
+
+	<...>
+
+	cpu@0 {
+		compatible = "arm,cortex-a9";
+		reg = <0>;
+
+		<...>
+
+		cpufreq_tbl = < 166000
+				200000
+				250000
+				300000
+				400000
+				500000
+				600000 >;
+	};
+
+	<...>
+
+};

Documentation/devicetree/bindings/gpio/gpio-stmpe.txt

@@ -0,0 +1,18 @@
+STMPE gpio
+----------
+
+Required properties:
+ - compatible: "st,stmpe-gpio"
+
+Optional properties:
+ - st,norequest-mask: bitmask specifying which GPIOs should _not_ be requestable
+   due to different usage (e.g. touch, keypad)
+
+Node name must be stmpe_gpio and should be child node of stmpe node to which it
+belongs.
+
+Example:
+	stmpe_gpio {
+		compatible = "st,stmpe-gpio";
+		st,norequest-mask = <0x20>;	//gpio 5 can't be used
+	};

Documentation/devicetree/bindings/gpio/gpio.txt

@@ -75,4 +75,40 @@ Example of two SOC GPIO banks defined as gpio-controller nodes:
 		gpio-controller;
 	};
 
+2.1) gpio-controller and pinctrl subsystem
+------------------------------------------
 
+gpio-controller on a SOC might be tightly coupled with the pinctrl
+subsystem, in the sense that the pins can be used by other functions
+together with optional gpio feature.
+
+While the pin allocation is totally managed by the pin ctrl subsystem,
+gpio (under gpiolib) is still maintained by gpio drivers. It may happen
+that different pin ranges in a SoC is managed by different gpio drivers.
+
+This makes it logical to let gpio drivers announce their pin ranges to
+the pin ctrl subsystem and call 'pinctrl_request_gpio' in order to
+request the corresponding pin before any gpio usage.
+
+For this, the gpio controller can use a pinctrl phandle and pins to
+announce the pinrange to the pin ctrl subsystem. For example,
+
+	qe_pio_e: gpio-controller@1460 {
+		#gpio-cells = <2>;
+		compatible = "fsl,qe-pario-bank-e", "fsl,qe-pario-bank";
+		reg = <0x1460 0x18>;
+		gpio-controller;
+		gpio-ranges = <&pinctrl1 20 10>, <&pinctrl2 50 20>;
+
+    }
+
+where,
+   &pinctrl1 and &pinctrl2 is the phandle to the pinctrl DT node.
+
+   Next values specify the base pin and number of pins for the range
+   handled by 'qe_pio_e' gpio. In the given example from base pin 20 to
+   pin 29 under pinctrl1 and pin 50 to pin 69 under pinctrl2 is handled
+   by this gpio controller.
+
+The pinctrl node must have "#gpio-range-cells" property to show number of
+arguments to pass with phandle from gpio controllers node.

Documentation/devicetree/bindings/gpio/gpio_atmel.txt

@@ -9,6 +9,10 @@ Required properties:
   unused).
 - gpio-controller: Marks the device node as a GPIO controller.
 
+optional properties:
+- #gpio-lines: Number of gpio if absent 32.
+
+
 Example:
 	pioA: gpio@fffff200 {
 		compatible = "atmel,at91rm9200-gpio";
@@ -16,5 +20,6 @@ Example:
 		interrupts = <2 4>;
 		#gpio-cells = <2>;
 		gpio-controller;
+		#gpio-lines = <19>;
 	};
 

Documentation/devicetree/bindings/gpio/spear_spics.txt

@@ -0,0 +1,50 @@
+=== ST Microelectronics SPEAr SPI CS Driver ===
+
+SPEAr platform provides a provision to control chipselects of ARM PL022 Prime
+Cell spi controller through its system registers, which otherwise remains under
+PL022 control. If chipselect remain under PL022 control then they would be
+released as soon as transfer is over and TxFIFO becomes empty. This is not
+desired by some of the device protocols above spi which expect (multiple)
+transfers without releasing their chipselects.
+
+Chipselects can be controlled by software by turning them as GPIOs. SPEAr
+provides another interface through system registers through which software can
+directly control each PL022 chipselect. Hence, it is natural for SPEAr to export
+the control of this interface as gpio.
+
+Required properties:
+
+  * compatible: should be defined as "st,spear-spics-gpio"
+  * reg: mentioning address range of spics controller
+  * st-spics,peripcfg-reg: peripheral configuration register offset
+  * st-spics,sw-enable-bit: bit offset to enable sw control
+  * st-spics,cs-value-bit: bit offset to drive chipselect low or high
+  * st-spics,cs-enable-mask: chip select number bit mask
+  * st-spics,cs-enable-shift: chip select number program offset
+  * gpio-controller: Marks the device node as gpio controller
+  * #gpio-cells: should be 1 and will mention chip select number
+
+All the above bit offsets are within peripcfg register.
+
+Example:
+-------
+spics: spics@e0700000{
+        compatible = "st,spear-spics-gpio";
+        reg = <0xe0700000 0x1000>;
+        st-spics,peripcfg-reg = <0x3b0>;
+        st-spics,sw-enable-bit = <12>;
+        st-spics,cs-value-bit = <11>;
+        st-spics,cs-enable-mask = <3>;
+        st-spics,cs-enable-shift = <8>;
+        gpio-controller;
+        #gpio-cells = <2>;
+};
+
+
+spi0: spi@e0100000 {
+        status = "okay";
+        num-cs = <3>;
+        cs-gpios = <&gpio1 7 0>, <&spics 0>,
+                   <&spics 1>;
+	...
+}

Documentation/devicetree/bindings/i2c/i2c-mv64xxx.txt

@@ -0,0 +1,18 @@
+
+* Marvell MV64XXX I2C controller
+
+Required properties :
+
+ - reg             : Offset and length of the register set for the device
+ - compatible      : Should be "marvell,mv64xxx-i2c"
+ - interrupts      : The interrupt number
+ - clock-frequency : Desired I2C bus clock frequency in Hz.
+
+Examples:
+
+	i2c@11000 {
+		compatible = "marvell,mv64xxx-i2c";
+		reg = <0x11000 0x20>;
+		interrupts = <29>;
+		clock-frequency = <100000>;
+	};

Documentation/devicetree/bindings/i2c/i2c-pxa.txt

@@ -31,21 +31,3 @@ Examples:
 		reg = <0xd4025000 0x1000>;
 		interrupts = <58>;
 	};
-
-* Marvell MV64XXX I2C controller
-
-Required properties :
-
- - reg             : Offset and length of the register set for the device
- - compatible      : Should be "marvell,mv64xxx-i2c"
- - interrupts      : The interrupt number
- - clock-frequency : Desired I2C bus clock frequency in Hz.
-
-Examples:
-
-	i2c@11000 {
-		compatible = "marvell,mv64xxx-i2c";
-		reg = <0x11000 0x20>;
-		interrupts = <29>;
-		clock-frequency = <100000>;
-	};

Documentation/devicetree/bindings/leds/common.txt

@@ -0,0 +1,23 @@
+Common leds properties.
+
+Optional properties for child nodes:
+- label : The label for this LED.  If omitted, the label is
+  taken from the node name (excluding the unit address).
+
+- linux,default-trigger :  This parameter, if present, is a
+    string defining the trigger assigned to the LED.  Current triggers are:
+     "backlight" - LED will act as a back-light, controlled by the framebuffer
+		   system
+     "default-on" - LED will turn on (but for leds-gpio see "default-state"
+		    property in Documentation/devicetree/bindings/gpio/led.txt)
+     "heartbeat" - LED "double" flashes at a load average based rate
+     "ide-disk" - LED indicates disk activity
+     "timer" - LED flashes at a fixed, configurable rate
+
+Examples:
+
+system-status {
+	label = "Status";
+	linux,default-trigger = "heartbeat";
+	...
+};

Documentation/devicetree/bindings/leds/leds-gpio.txt

@@ -10,16 +10,10 @@ LED sub-node properties:
 - gpios :  Should specify the LED's GPIO, see "gpios property" in
   Documentation/devicetree/bindings/gpio/gpio.txt.  Active low LEDs should be
   indicated using flags in the GPIO specifier.
-- label :  (optional) The label for this LED.  If omitted, the label is
-  taken from the node name (excluding the unit address).
-- linux,default-trigger :  (optional) This parameter, if present, is a
-  string defining the trigger assigned to the LED.  Current triggers are:
-    "backlight" - LED will act as a back-light, controlled by the framebuffer
-		  system
-    "default-on" - LED will turn on, but see "default-state" below
-    "heartbeat" - LED "double" flashes at a load average based rate
-    "ide-disk" - LED indicates disk activity
-    "timer" - LED flashes at a fixed, configurable rate
+- label :  (optional)
+  see Documentation/devicetree/bindings/leds/common.txt
+- linux,default-trigger :  (optional)
+  see Documentation/devicetree/bindings/leds/common.txt
 - default-state:  (optional) The initial state of the LED.  Valid
   values are "on", "off", and "keep".  If the LED is already on or off
   and the default-state property is set the to same value, then no

Documentation/devicetree/bindings/mmc/mmc.txt

@@ -21,6 +21,12 @@ Optional properties:
 - cd-inverted: when present, polarity on the cd gpio line is inverted
 - wp-inverted: when present, polarity on the wp gpio line is inverted
 - max-frequency: maximum operating clock frequency
+- no-1-8-v: when present, denotes that 1.8v card voltage is not supported on
+  this system, even if the controller claims it is.
+
+Optional SDIO properties:
+- keep-power-in-suspend: Preserves card power during a suspend/resume cycle
+- enable-sdio-wakeup: Enables wake up of host system on SDIO IRQ assertion
 
 Example:
 
@@ -33,4 +39,6 @@ sdhci@ab000000 {
 	cd-inverted;
 	wp-gpios = <&gpio 70 0>;
 	max-frequency = <50000000>;
+	keep-power-in-suspend;
+	enable-sdio-wakeup;
 }

Documentation/devicetree/bindings/mmc/samsung-sdhci.txt

@@ -12,10 +12,6 @@ is used. The Samsung's SDHCI controller bindings extends this as listed below.
 [A] The property "samsung,cd-pinmux-gpio" can be used as stated in the
     "Optional Board Specific Properties" section below.
 
-[B] If core card-detect bindings and "samsung,cd-pinmux-gpio" property
-    is not specified, it is assumed that there is no card detection
-    mechanism used.
-
 Required SoC Specific Properties:
 - compatible: should be one of the following
   - "samsung,s3c6410-sdhci": For controllers compatible with s3c6410 sdhci
@@ -24,14 +20,18 @@ Required SoC Specific Properties:
     controller.
 
 Required Board Specific Properties:
-- gpios: Should specify the gpios used for clock, command and data lines. The
-  gpio specifier format depends on the gpio controller.
+- Samsung GPIO variant (will be completely replaced by pinctrl):
+  - gpios: Should specify the gpios used for clock, command and data lines. The
+    gpio specifier format depends on the gpio controller.
+- Pinctrl variant (preferred if available):
+  - pinctrl-0: Should specify pin control groups used for this controller.
+  - pinctrl-names: Should contain only one value - "default".
 
 Optional Board Specific Properties:
 - samsung,cd-pinmux-gpio: Specifies the card detect line that is routed
   through a pinmux to the card-detect pin of the card slot. This property
   should be used only if none of the mmc core card-detect properties are
-  used.
+  used. Only for Samsung GPIO variant.
 
 Example:
 	sdhci@12530000 {
@@ -40,12 +40,18 @@ Example:
 		interrupts = <0 75 0>;
 		bus-width = <4>;
 		cd-gpios = <&gpk2 2 2 3 3>;
+
+		/* Samsung GPIO variant */
 		gpios = <&gpk2 0 2 0 3>,  /* clock line */
 			<&gpk2 1 2 0 3>,  /* command line */
 			<&gpk2 3 2 3 3>,  /* data line 0 */
 			<&gpk2 4 2 3 3>,  /* data line 1 */
 			<&gpk2 5 2 3 3>,  /* data line 2 */
 			<&gpk2 6 2 3 3>;  /* data line 3 */
+
+		/* Pinctrl variant */
+		pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus4>;
+		pinctrl-names = "default";
 	};
 
 	Note: This example shows both SoC specific and board specific properties

Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt

@@ -19,6 +19,7 @@ ti,dual-volt: boolean, supports dual voltage cards
 "supply-name" examples are "vmmc", "vmmc_aux" etc
 ti,non-removable: non-removable slot (like eMMC)
 ti,needs-special-reset: Requires a special softreset sequence
+ti,needs-special-hs-handling: HSMMC IP needs special setting for handling High Speed
 
 Example:
 	mmc1: mmc@0x4809c000 {

Documentation/devicetree/bindings/mmc/vt8500-sdmmc.txt

@@ -0,0 +1,23 @@
+* Wondermedia WM8505/WM8650 SD/MMC Host Controller
+
+This file documents differences between the core properties described
+by mmc.txt and the properties used by the wmt-sdmmc driver.
+
+Required properties:
+- compatible: Should be "wm,wm8505-sdhc".
+- interrupts: Two interrupts are required - regular irq and dma irq.
+
+Optional properties:
+- sdon-inverted: SD_ON bit is inverted on the controller
+
+Examples:
+
+sdhc@d800a000 {
+	compatible = "wm,wm8505-sdhc";
+	reg = <0xd800a000 0x1000>;
+	interrupts = <20 21>;
+	clocks = <&sdhc>;
+	bus-width = <4>;
+	sdon-inverted;
+};
+

Documentation/devicetree/bindings/net/mdio-gpio.txt

@@ -8,9 +8,16 @@ gpios property as described in section VIII.1 in the following order:
 
 MDC, MDIO.
 
+Note: Each gpio-mdio bus should have an alias correctly numbered in "aliases"
+node.
+
 Example:
 
-mdio {
+aliases {
+	mdio-gpio0 = <&mdio0>;
+};
+
+mdio0: mdio {
 	compatible = "virtual,mdio-gpio";
 	#address-cells = <1>;
 	#size-cells = <0>;

Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt

@@ -0,0 +1,141 @@
+* Atmel AT91 Pinmux Controller
+
+The AT91 Pinmux Controler, enables the IC
+to share one PAD to several functional blocks. The sharing is done by
+multiplexing the PAD input/output signals. For each PAD there are up to
+8 muxing options (called periph modes). Since different modules require
+different PAD settings (like pull up, keeper, etc) the contoller controls
+also the PAD settings parameters.
+
+Please refer to pinctrl-bindings.txt in this directory for details of the
+common pinctrl bindings used by client devices, including the meaning of the
+phrase "pin configuration node".
+
+Atmel AT91 pin configuration node is a node of a group of pins which can be
+used for a specific device or function. This node represents both mux and config
+of the pins in that group. The 'pins' selects the function mode(also named pin
+mode) this pin can work on and the 'config' configures various pad settings
+such as pull-up, multi drive, etc.
+
+Required properties for iomux controller:
+- compatible: "atmel,at91rm9200-pinctrl"
+- atmel,mux-mask: array of mask (periph per bank) to describe if a pin can be
+  configured in this periph mode. All the periph and bank need to be describe.
+
+How to create such array:
+
+Each column will represent the possible peripheral of the pinctrl
+Each line will represent a pio bank
+
+Take an example on the 9260
+Peripheral: 2 ( A and B)
+Bank: 3 (A, B and C)
+=>
+
+  /*    A         B     */
+  0xffffffff 0xffc00c3b  /* pioA */
+  0xffffffff 0x7fff3ccf  /* pioB */
+  0xffffffff 0x007fffff  /* pioC */
+
+For each peripheral/bank we will descibe in a u32 if a pin can can be
+configured in it by putting 1 to the pin bit (1 << pin)
+
+Let's take the pioA on peripheral B
+From the datasheet Table 10-2.
+Peripheral B
+PA0	MCDB0
+PA1	MCCDB
+PA2
+PA3	MCDB3
+PA4	MCDB2
+PA5	MCDB1
+PA6
+PA7
+PA8
+PA9
+PA10	ETX2
+PA11	ETX3
+PA12
+PA13
+PA14
+PA15
+PA16
+PA17
+PA18
+PA19
+PA20
+PA21
+PA22	ETXER
+PA23	ETX2
+PA24	ETX3
+PA25	ERX2
+PA26	ERX3
+PA27	ERXCK
+PA28	ECRS
+PA29	ECOL
+PA30	RXD4
+PA31	TXD4
+
+=> 0xffc00c3b
+
+Required properties for pin configuration node:
+- atmel,pins: 4 integers array, represents a group of pins mux and config
+  setting. The format is atmel,pins = <PIN_BANK PIN_BANK_NUM PERIPH CONFIG>.
+  The PERIPH 0 means gpio.
+
+Bits used for CONFIG:
+PULL_UP		(1 << 0): indicate this pin need a pull up.
+MULTIDRIVE	(1 << 1): indicate this pin need to be configured as multidrive.
+DEGLITCH	(1 << 2): indicate this pin need deglitch.
+PULL_DOWN	(1 << 3): indicate this pin need a pull down.
+DIS_SCHMIT	(1 << 4): indicate this pin need to disable schmit trigger.
+DEBOUNCE	(1 << 16): indicate this pin need debounce.
+DEBOUNCE_VAL	(0x3fff << 17): debounce val.
+
+NOTE:
+Some requirements for using atmel,at91rm9200-pinctrl binding:
+1. We have pin function node defined under at91 controller node to represent
+   what pinmux functions this SoC supports.
+2. The driver can use the function node's name and pin configuration node's
+   name describe the pin function and group hierarchy.
+   For example, Linux at91 pinctrl driver takes the function node's name
+   as the function name and pin configuration node's name as group name to
+   create the map table.
+3. Each pin configuration node should have a phandle, devices can set pins
+   configurations by referring to the phandle of that pin configuration node.
+4. The gpio controller must be describe in the pinctrl simple-bus.
+
+Examples:
+
+pinctrl@fffff400 {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	ranges;
+	compatible = "atmel,at91rm9200-pinctrl", "simple-bus";
+	reg = <0xfffff400 0x600>;
+
+	atmel,mux-mask = <
+	      /*    A         B     */
+	       0xffffffff 0xffc00c3b  /* pioA */
+	       0xffffffff 0x7fff3ccf  /* pioB */
+	       0xffffffff 0x007fffff  /* pioC */
+	      >;
+
+	/* shared pinctrl settings */
+	dbgu {
+		pinctrl_dbgu: dbgu-0 {
+			atmel,pins =
+				<1 14 0x1 0x0	/* PB14 periph A */
+				 1 15 0x1 0x1>;	/* PB15 periph with pullup */
+		};
+	};
+};
+
+dbgu: serial@fffff200 {
+	compatible = "atmel,at91sam9260-usart";
+	reg = <0xfffff200 0x200>;
+	interrupts = <1 4 7>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_dbgu>;
+	status = "disabled";
+};

Documentation/devicetree/bindings/rtc/orion-rtc.txt

@@ -0,0 +1,18 @@
+* Mvebu Real Time Clock
+
+RTC controller for the Kirkwood, the Dove, the Armada 370 and the
+Armada XP SoCs
+
+Required properties:
+- compatible : Should be "marvell,orion-rtc"
+- reg: physical base address of the controller and length of memory mapped
+  region.
+- interrupts: IRQ line for the RTC.
+
+Example:
+
+rtc@10300 {
+        compatible = "marvell,orion-rtc";
+        reg = <0xd0010300 0x20>;
+        interrupts = <50>;
+};

Documentation/devicetree/bindings/tty/serial/fsl-mxs-auart.txt

@@ -6,11 +6,19 @@ Required properties:
 - reg : Address and length of the register set for the device
 - interrupts : Should contain the auart interrupt numbers
 
+Optional properties:
+- fsl,auart-dma-channel : The DMA channels, the first is for RX, the other
+		is for TX. If you add this property, it also means that you
+		will enable the DMA support for the auart.
+		Note: due to the hardware bug in imx23(see errata : 2836),
+		only the imx28 can enable the DMA support for the auart.
+
 Example:
 auart0: serial@8006a000 {
 	compatible = "fsl,imx28-auart", "fsl,imx23-auart";
 	reg = <0x8006a000 0x2000>;
 	interrupts = <112 70 71>;
+	fsl,auart-dma-channel = <8 9>;
 };
 
 Note: Each auart port should have an alias correctly numbered in "aliases"

Documentation/devicetree/bindings/tty/serial/of-serial.txt

@@ -14,7 +14,10 @@ Required properties:
 	- "serial" if the port type is unknown.
 - reg : offset and length of the register set for the device.
 - interrupts : should contain uart interrupt.
-- clock-frequency : the input clock frequency for the UART.
+- clock-frequency : the input clock frequency for the UART
+	 or
+  clocks phandle to refer to the clk used as per Documentation/devicetree
+  /bindings/clock/clock-bindings.txt
 
 Optional properties:
 - current-speed : the current active speed of the UART.

Documentation/devicetree/bindings/usb/am33xx-usb.txt

@@ -3,12 +3,12 @@ AM33XX MUSB GLUE
  - ti,hwmods : must be "usb_otg_hs"
  - multipoint : Should be "1" indicating the musb controller supports
    multipoint. This is a MUSB configuration-specific setting.
- - num_eps : Specifies the number of endpoints. This is also a
+ - num-eps : Specifies the number of endpoints. This is also a
    MUSB configuration-specific setting. Should be set to "16"
- - ram_bits : Specifies the ram address size. Should be set to "12"
- - port0_mode : Should be "3" to represent OTG. "1" signifies HOST and "2"
+ - ram-bits : Specifies the ram address size. Should be set to "12"
+ - port0-mode : Should be "3" to represent OTG. "1" signifies HOST and "2"
    represents PERIPHERAL.
- - port1_mode : Should be "1" to represent HOST. "3" signifies OTG and "2"
+ - port1-mode : Should be "1" to represent HOST. "3" signifies OTG and "2"
    represents PERIPHERAL.
  - power : Should be "250". This signifies the controller can supply upto
    500mA when operating in host mode.

Documentation/devicetree/bindings/vendor-prefixes.txt

@@ -5,6 +5,7 @@ using them to avoid name-space collisions.
 
 ad	Avionic Design GmbH
 adi	Analog Devices, Inc.
+ak	Asahi Kasei Corp.
 amcc	Applied Micro Circuits Corporation (APM, formally AMCC)
 apm	Applied Micro Circuits Corporation (APM)
 arm	ARM Ltd.
@@ -25,6 +26,7 @@ gef	GE Fanuc Intelligent Platforms Embedded Systems, Inc.
 hp	Hewlett Packard
 ibm	International Business Machines (IBM)
 idt	Integrated Device Technologies, Inc.
+img	Imagination Technologies Ltd.
 intercontrol	Inter Control Group
 linux	Linux-specific binding
 marvell	Marvell Technology Group Ltd.
@@ -34,8 +36,9 @@ national	National Semiconductor
 nintendo	Nintendo
 nvidia	NVIDIA
 nxp	NXP Semiconductors
+onnn	ON Semiconductor Corp.
 picochip	Picochip Ltd
-powervr	Imagination Technologies
+powervr	PowerVR (deprecated, use img)
 qcom	Qualcomm, Inc.
 ramtron	Ramtron International
 realtek Realtek Semiconductor Corp.
@@ -45,6 +48,7 @@ schindler	Schindler
 sil	Silicon Image
 simtek
 sirf	SiRF Technology, Inc.
+snps 	Synopsys, Inc.
 st	STMicroelectronics
 stericsson	ST-Ericsson
 ti	Texas Instruments

Documentation/devicetree/usage-model.txt

@@ -347,7 +347,7 @@ later), which will happily live at the base of the Linux /sys/devices
 tree.  Therefore, if a DT node is at the root of the tree, then it
 really probably is best registered as a platform_device.
 
-Linux board support code calls of_platform_populate(NULL, NULL, NULL)
+Linux board support code calls of_platform_populate(NULL, NULL, NULL, NULL)
 to kick off discovery of devices at the root of the tree.  The
 parameters are all NULL because when starting from the root of the
 tree, there is no need to provide a starting node (the first NULL), a