Merge branch 'linus' into sched/urgent, to resolve conflicts

Conflicts:
	arch/arm64/kernel/entry.S
	arch/x86/Kconfig
	include/linux/sched/mm.h
	kernel/fork.c

Signed-off-by: Ingo Molnar <[email protected]>

arch/arm64/Kconfig

@@ -60,6 +60,7 @@ config ARM64
 	select COMMON_CLK
 	select CPU_PM if (SUSPEND || CPU_IDLE)
 	select DCACHE_WORD_ACCESS
+	select DMA_DIRECT_OPS
 	select EDAC_SUPPORT
 	select FRAME_POINTER
 	select GENERIC_ALLOCATOR
@@ -91,6 +92,7 @@ config ARM64
 	select HAVE_ARCH_MMAP_RND_BITS
 	select HAVE_ARCH_MMAP_RND_COMPAT_BITS if COMPAT
 	select HAVE_ARCH_SECCOMP_FILTER
+	select HAVE_ARCH_THREAD_STRUCT_WHITELIST
 	select HAVE_ARCH_TRACEHOOK
 	select HAVE_ARCH_TRANSPARENT_HUGEPAGE
 	select HAVE_ARCH_VMAP_STACK
@@ -228,7 +230,7 @@ config GENERIC_CSUM
 config GENERIC_CALIBRATE_DELAY
 	def_bool y
 
-config ZONE_DMA
+config ZONE_DMA32
 	def_bool y
 
 config HAVE_GENERIC_GUP
@@ -523,20 +525,13 @@ config CAVIUM_ERRATUM_30115
 config QCOM_FALKOR_ERRATUM_1003
 	bool "Falkor E1003: Incorrect translation due to ASID change"
 	default y
-	select ARM64_PAN if ARM64_SW_TTBR0_PAN
 	help
 	  On Falkor v1, an incorrect ASID may be cached in the TLB when ASID
-	  and BADDR are changed together in TTBRx_EL1. The workaround for this
-	  issue is to use a reserved ASID in cpu_do_switch_mm() before
-	  switching to the new ASID. Saying Y here selects ARM64_PAN if
-	  ARM64_SW_TTBR0_PAN is selected. This is done because implementing and
-	  maintaining the E1003 workaround in the software PAN emulation code
-	  would be an unnecessary complication. The affected Falkor v1 CPU
-	  implements ARMv8.1 hardware PAN support and using hardware PAN
-	  support versus software PAN emulation is mutually exclusive at
-	  runtime.
-
-	  If unsure, say Y.
+	  and BADDR are changed together in TTBRx_EL1. Since we keep the ASID
+	  in TTBR1_EL1, this situation only occurs in the entry trampoline and
+	  then only for entries in the walk cache, since the leaf translation
+	  is unchanged. Work around the erratum by invalidating the walk cache
+	  entries for the trampoline before entering the kernel proper.
 
 config QCOM_FALKOR_ERRATUM_1009
 	bool "Falkor E1009: Prematurely complete a DSB after a TLBI"
@@ -657,6 +652,35 @@ config ARM64_VA_BITS
 	default 47 if ARM64_VA_BITS_47
 	default 48 if ARM64_VA_BITS_48
 
+choice
+	prompt "Physical address space size"
+	default ARM64_PA_BITS_48
+	help
+	  Choose the maximum physical address range that the kernel will
+	  support.
+
+config ARM64_PA_BITS_48
+	bool "48-bit"
+
+config ARM64_PA_BITS_52
+	bool "52-bit (ARMv8.2)"
+	depends on ARM64_64K_PAGES
+	depends on ARM64_PAN || !ARM64_SW_TTBR0_PAN
+	help
+	  Enable support for a 52-bit physical address space, introduced as
+	  part of the ARMv8.2-LPA extension.
+
+	  With this enabled, the kernel will also continue to work on CPUs that
+	  do not support ARMv8.2-LPA, but with some added memory overhead (and
+	  minor performance overhead).
+
+endchoice
+
+config ARM64_PA_BITS
+	int
+	default 48 if ARM64_PA_BITS_48
+	default 52 if ARM64_PA_BITS_52
+
 config CPU_BIG_ENDIAN
        bool "Build big-endian kernel"
        help
@@ -851,6 +875,35 @@ config FORCE_MAX_ZONEORDER
 	  However for 4K, we choose a higher default value, 11 as opposed to 10, giving us
 	  4M allocations matching the default size used by generic code.
 
+config UNMAP_KERNEL_AT_EL0
+	bool "Unmap kernel when running in userspace (aka \"KAISER\")" if EXPERT
+	default y
+	help
+	  Speculation attacks against some high-performance processors can
+	  be used to bypass MMU permission checks and leak kernel data to
+	  userspace. This can be defended against by unmapping the kernel
+	  when running in userspace, mapping it back in on exception entry
+	  via a trampoline page in the vector table.
+
+	  If unsure, say Y.
+
+config HARDEN_BRANCH_PREDICTOR
+	bool "Harden the branch predictor against aliasing attacks" if EXPERT
+	default y
+	help
+	  Speculation attacks against some high-performance processors rely on
+	  being able to manipulate the branch predictor for a victim context by
+	  executing aliasing branches in the attacker context.  Such attacks
+	  can be partially mitigated against by clearing internal branch
+	  predictor state and limiting the prediction logic in some situations.
+
+	  This config option will take CPU-specific actions to harden the
+	  branch predictor against aliasing attacks and may rely on specific
+	  instruction sequences or control bits being set by the system
+	  firmware.
+
+	  If unsure, say Y.
+
 menuconfig ARMV8_DEPRECATED
 	bool "Emulate deprecated/obsolete ARMv8 instructions"
 	depends on COMPAT
@@ -1022,6 +1075,22 @@ config ARM64_PMEM
 	  operations if DC CVAP is not supported (following the behaviour of
 	  DC CVAP itself if the system does not define a point of persistence).
 
+config ARM64_RAS_EXTN
+	bool "Enable support for RAS CPU Extensions"
+	default y
+	help
+	  CPUs that support the Reliability, Availability and Serviceability
+	  (RAS) Extensions, part of ARMv8.2 are able to track faults and
+	  errors, classify them and report them to software.
+
+	  On CPUs with these extensions system software can use additional
+	  barriers to determine if faults are pending and read the
+	  classification from a new set of registers.
+
+	  Selecting this feature will allow the kernel to use these barriers
+	  and access the new registers if the system supports the extension.
+	  Platform RAS features may additionally depend on firmware support.
+
 endmenu
 
 config ARM64_SVE

arch/arm64/Kconfig.platforms

@@ -105,6 +105,7 @@ config ARCH_MESON
 	select PINCTRL_MESON
 	select COMMON_CLK_AMLOGIC
 	select COMMON_CLK_GXBB
+	select COMMON_CLK_AXG
 	select MESON_IRQ_GPIO
 	help
 	  This enables support for the Amlogic S905 SoCs.

arch/arm64/boot/dts/actions/Makefile

@@ -1 +1,3 @@
+dtb-$(CONFIG_ARCH_ACTIONS) += s700-cubieboard7.dtb
+
 dtb-$(CONFIG_ARCH_ACTIONS) += s900-bubblegum-96.dtb

arch/arm64/boot/dts/actions/s700-cubieboard7.dts

@@ -0,0 +1,46 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2017 Andreas Färber
+ */
+
+/dts-v1/;
+
+#include "s700.dtsi"
+
+/ {
+	compatible = "cubietech,cubieboard7", "actions,s700";
+	model = "CubieBoard7";
+
+	aliases {
+		serial3 = &uart3;
+	};
+
+	chosen {
+		stdout-path = "serial3:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x0 0x0 0x80000000>;
+	};
+
+	memory@1,e0000000 {
+		device_type = "memory";
+		reg = <0x1 0xe0000000 0x0 0x0>;
+	};
+
+	uart3_clk: uart3-clk {
+		compatible = "fixed-clock";
+		clock-frequency = <921600>;
+		#clock-cells = <0>;
+	};
+};
+
+&timer {
+	clocks = <&hosc>;
+};
+
+&uart3 {
+	status = "okay";
+	clocks = <&uart3_clk>;
+};

arch/arm64/boot/dts/actions/s700.dtsi

@@ -0,0 +1,169 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2017 Andreas Färber
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+/ {
+	compatible = "actions,s700";
+	interrupt-parent = <&gic>;
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	cpus {
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cpu0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53", "arm,armv8";
+			reg = <0x0 0x0>;
+			enable-method = "psci";
+		};
+
+		cpu1: cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53", "arm,armv8";
+			reg = <0x0 0x1>;
+			enable-method = "psci";
+		};
+
+		cpu2: cpu@2 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53", "arm,armv8";
+			reg = <0x0 0x2>;
+			enable-method = "psci";
+		};
+
+		cpu3: cpu@3 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53", "arm,armv8";
+			reg = <0x0 0x3>;
+			enable-method = "psci";
+		};
+	};
+
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		secmon@1f000000 {
+			reg = <0x0 0x1f000000 0x0 0x1000000>;
+			no-map;
+		};
+	};
+
+	psci {
+		compatible = "arm,psci-0.2";
+		method = "smc";
+	};
+
+	arm-pmu {
+		compatible = "arm,cortex-a53-pmu";
+		interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
+		             <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>,
+		             <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>,
+		             <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>;
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		interrupts = <GIC_PPI 13
+			(GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 14
+			(GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 11
+			(GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 10
+			(GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
+	};
+
+	hosc: hosc {
+		compatible = "fixed-clock";
+		clock-frequency = <24000000>;
+		#clock-cells = <0>;
+	};
+
+	soc {
+		compatible = "simple-bus";
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		gic: interrupt-controller@e00f1000 {
+			compatible = "arm,gic-400";
+			reg = <0x0 0xe00f1000 0x0 0x1000>,
+			      <0x0 0xe00f2000 0x0 0x2000>,
+			      <0x0 0xe00f4000 0x0 0x2000>,
+			      <0x0 0xe00f6000 0x0 0x2000>;
+			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
+			interrupt-controller;
+			#interrupt-cells = <3>;
+		};
+
+		uart0: serial@e0120000 {
+			compatible = "actions,s900-uart", "actions,owl-uart";
+			reg = <0x0 0xe0120000 0x0 0x2000>;
+			interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+		};
+
+		uart1: serial@e0122000 {
+			compatible = "actions,s900-uart", "actions,owl-uart";
+			reg = <0x0 0xe0122000 0x0 0x2000>;
+			interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+		};
+
+		uart2: serial@e0124000 {
+			compatible = "actions,s900-uart", "actions,owl-uart";
+			reg = <0x0 0xe0124000 0x0 0x2000>;
+			interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+		};
+
+		uart3: serial@e0126000 {
+			compatible = "actions,s900-uart", "actions,owl-uart";
+			reg = <0x0 0xe0126000 0x0 0x2000>;
+			interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+		};
+
+		uart4: serial@e0128000 {
+			compatible = "actions,s900-uart", "actions,owl-uart";
+			reg = <0x0 0xe0128000 0x0 0x2000>;
+			interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+		};
+
+		uart5: serial@e012a000 {
+			compatible = "actions,s900-uart", "actions,owl-uart";
+			reg = <0x0 0xe012a000 0x0 0x2000>;
+			interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+		};
+
+		uart6: serial@e012c000 {
+			compatible = "actions,s900-uart", "actions,owl-uart";
+			reg = <0x0 0xe012c000 0x0 0x2000>;
+			interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+		};
+
+		sps: power-controller@e01b0100 {
+			compatible = "actions,s700-sps";
+			reg = <0x0 0xe01b0100 0x0 0x100>;
+			#power-domain-cells = <1>;
+		};
+
+		timer: timer@e024c000 {
+			compatible = "actions,s700-timer";
+			reg = <0x0 0xe024c000 0x0 0x4000>;
+			interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "timer1";
+		};
+	};
+};

arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts

@@ -60,6 +60,26 @@
 		stdout-path = "serial0:115200n8";
 	};
 
+	leds {
+		compatible = "gpio-leds";
+
+		pwr-led {
+			label = "bananapi-m64:red:pwr";
+			gpios = <&pio 3 24 GPIO_ACTIVE_HIGH>; /* PD24 */
+			default-state = "on";
+		};
+
+		green {
+			label = "bananapi-m64:green:user";
+			gpios = <&pio 4 14 GPIO_ACTIVE_HIGH>; /* PE14 */
+		};
+
+		blue {
+			label = "bananapi-m64:blue:user";
+			gpios = <&pio 4 15 GPIO_ACTIVE_HIGH>; /* PE15 */
+		};
+	};
+
 	wifi_pwrseq: wifi_pwrseq {
 		compatible = "mmc-pwrseq-simple";
 		reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 */
@@ -153,6 +173,17 @@
 
 #include "axp803.dtsi"
 
+&reg_aldo1 {
+	/*
+	 * This regulator also drives the PE pingroup GPIOs,
+	 * which also controls two LEDs.
+	 */
+	regulator-always-on;
+	regulator-min-microvolt = <2800000>;
+	regulator-max-microvolt = <2800000>;
+	regulator-name = "afvcc-csi";
+};
+
 &reg_aldo2 {
 	regulator-always-on;
 	regulator-min-microvolt = <1800000>;
@@ -168,6 +199,11 @@
 };
 
 &reg_dc1sw {
+	/*
+	 * This regulator also indirectly drives the PD pingroup GPIOs,
+	 * which also controls the power LED.
+	 */
+	regulator-always-on;
 	regulator-name = "vcc-phy";
 };
 

arch/arm64/boot/dts/allwinner/sun50i-a64-olinuxino.dts

@@ -57,6 +57,11 @@
 	chosen {
 		stdout-path = "serial0:115200n8";
 	};
+
+	wifi_pwrseq: wifi_pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 */
+	};
 };
 
 &mmc0 {
@@ -70,6 +75,24 @@
 	status = "okay";
 };
 
+&mmc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc1_pins>;
+	vmmc-supply = <&reg_aldo2>;
+	vqmmc-supply = <&reg_dldo4>;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	bus-width = <4>;
+	non-removable;
+	status = "okay";
+
+	rtl8723bs: wifi@1 {
+		reg = <1>;
+		interrupt-parent = <&r_pio>;
+		interrupts = <0 3 IRQ_TYPE_LEVEL_LOW>; /* PL3 */
+		interrupt-names = "host-wake";
+	};
+};
+
 &r_rsb {
 	status = "okay";
 

arch/arm64/boot/dts/allwinner/sun50i-a64-orangepi-win.dts

@@ -57,13 +57,6 @@
 	chosen {
 		stdout-path = "serial0:115200n8";
 	};
-
-	reg_vcc3v3: vcc3v3 {
-		compatible = "regulator-fixed";
-		regulator-name = "vcc3v3";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-	};
 };
 
 &ehci1 {
@@ -73,7 +66,7 @@
 &mmc0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc0_pins>;
-	vmmc-supply = <&reg_vcc3v3>;
+	vmmc-supply = <&reg_dcdc1>;
 	cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>;
 	cd-inverted;
 	status = "okay";
@@ -83,6 +76,122 @@
 	status = "okay";
 };
 
+&r_rsb {
+	status = "okay";
+
+	axp803: pmic@3a3 {
+		compatible = "x-powers,axp803";
+		reg = <0x3a3>;
+		interrupt-parent = <&r_intc>;
+		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+	};
+};
+
+#include "axp803.dtsi"
+
+&reg_aldo1 {
+	regulator-always-on;
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "afvcc-csi";
+};
+
+&reg_aldo2 {
+	regulator-always-on;
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-pl";
+};
+
+&reg_aldo3 {
+	regulator-always-on;
+	regulator-min-microvolt = <3000000>;
+	regulator-max-microvolt = <3000000>;
+	regulator-name = "vcc-pll-avcc";
+};
+
+&reg_dcdc1 {
+	regulator-always-on;
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-3v3";
+};
+
+&reg_dcdc2 {
+	regulator-always-on;
+	regulator-min-microvolt = <1040000>;
+	regulator-max-microvolt = <1300000>;
+	regulator-name = "vdd-cpux";
+};
+
+/* DCDC3 is polyphased with DCDC2 */
+
+&reg_dcdc5 {
+	regulator-always-on;
+	regulator-min-microvolt = <1500000>;
+	regulator-max-microvolt = <1500000>;
+	regulator-name = "vcc-dram";
+};
+
+&reg_dcdc6 {
+	regulator-always-on;
+	regulator-min-microvolt = <1100000>;
+	regulator-max-microvolt = <1100000>;
+	regulator-name = "vdd-sys";
+};
+
+&reg_dldo1 {
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-hdmi-dsi";
+};
+
+&reg_dldo2 {
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-wifi";
+};
+
+&reg_dldo3 {
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "avdd-csi";
+};
+
+&reg_dldo4 {
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-wifi-io";
+};
+
+&reg_eldo1 {
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <1800000>;
+	regulator-name = "cpvdd";
+};
+
+&reg_fldo1 {
+	regulator-min-microvolt = <1200000>;
+	regulator-max-microvolt = <1200000>;
+	regulator-name = "vcc-1v2-hsic";
+};
+
+/*
+ * The A64 chip cannot work without this regulator off, although
+ * it seems to be only driving the AR100 core.
+ * Maybe we don't still know well about CPUs domain.
+ */
+&reg_fldo2 {
+	regulator-always-on;
+	regulator-min-microvolt = <1100000>;
+	regulator-max-microvolt = <1100000>;
+	regulator-name = "vdd-cpus";
+};
+
+&reg_rtc_ldo {
+	regulator-name = "vcc-rtc";
+};
+
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_pins_a>;

arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-neo-plus2.dts

@@ -53,6 +53,7 @@
 	compatible = "friendlyarm,nanopi-neo-plus2", "allwinner,sun50i-h5";
 
 	aliases {
+		ethernet0 = &emac;
 		serial0 = &uart0;
 	};
 
@@ -133,9 +134,25 @@
 	status = "okay";
 };
 
+&emac {
+	pinctrl-names = "default";
+	pinctrl-0 = <&emac_rgmii_pins>;
+	phy-supply = <&reg_gmac_3v3>;
+	phy-handle = <&ext_rgmii_phy>;
+	phy-mode = "rgmii";
+	status = "okay";
+};
+
+&external_mdio {
+	ext_rgmii_phy: ethernet-phy@7 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <7>;
+	};
+};
+
 &mmc0 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
+	pinctrl-0 = <&mmc0_pins_a>;
 	vmmc-supply = <&reg_vcc3v3>;
 	bus-width = <4>;
 	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */

arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-neo2.dts

@@ -127,7 +127,7 @@
 
 &mmc0 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
+	pinctrl-0 = <&mmc0_pins_a>;
 	vmmc-supply = <&reg_vcc3v3>;
 	bus-width = <4>;
 	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */

arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts

@@ -161,7 +161,7 @@
 
 &mmc0 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
+	pinctrl-0 = <&mmc0_pins_a>;
 	vmmc-supply = <&reg_vcc3v3>;
 	bus-width = <4>;
 	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */

arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-prime.dts

@@ -168,7 +168,7 @@
 
 &mmc0 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
+	pinctrl-0 = <&mmc0_pins_a>;
 	vmmc-supply = <&reg_vcc3v3>;
 	bus-width = <4>;
 	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */

arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-zero-plus2.dts

@@ -64,17 +64,43 @@
 		regulator-min-microvolt = <3300000>;
 		regulator-max-microvolt = <3300000>;
 	};
+
+	wifi_pwrseq: wifi_pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		pinctrl-names = "default";
+		reset-gpios = <&pio 0 9 GPIO_ACTIVE_LOW>; /* PA9 */
+		post-power-on-delay-ms = <200>;
+	};
 };
 
 &mmc0 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
+	pinctrl-0 = <&mmc0_pins_a>;
 	vmmc-supply = <&reg_vcc3v3>;
 	bus-width = <4>;
 	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
 	status = "okay";
 };
 
+&mmc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc1_pins_a>;
+	vmmc-supply = <&reg_vcc3v3>;
+	vqmmc-supply = <&reg_vcc3v3>;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	bus-width = <4>;
+	non-removable;
+	status = "okay";
+
+	brcmf: wifi@1 {
+		reg = <1>;
+		compatible = "brcm,bcm4329-fmac";
+		interrupt-parent = <&r_pio>;
+		interrupts = <0 7 IRQ_TYPE_LEVEL_LOW>;	/* PL7 */
+		interrupt-names = "host-wake";
+	};
+};
+
 &mmc2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc2_8bit_pins>;
@@ -90,3 +116,9 @@
 	pinctrl-0 = <&uart0_pins_a>;
 	status = "okay";
 };
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
+	status = "okay";
+};

arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi

@@ -98,6 +98,10 @@
 	compatible = "allwinner,sun50i-h5-ccu";
 };
 
+&display_clocks {
+	compatible = "allwinner,sun50i-h5-de2-clk";
+};
+
 &mmc0 {
 	compatible = "allwinner,sun50i-h5-mmc",
 		     "allwinner,sun50i-a64-mmc";

arch/arm64/boot/dts/altera/socfpga_stratix10.dtsi

@@ -249,7 +249,9 @@
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <0xffda4000 0x1000>;
-			interrupts = <0 101 4>;
+			interrupts = <0 99 4>;
+			resets = <&rst SPIM0_RESET>;
+			reg-io-width = <4>;
 			num-chipselect = <4>;
 			bus-num = <0>;
 			status = "disabled";
@@ -260,7 +262,9 @@
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <0xffda5000 0x1000>;
-			interrupts = <0 102 4>;
+			interrupts = <0 100 4>;
+			resets = <&rst SPIM1_RESET>;
+			reg-io-width = <4>;
 			num-chipselect = <4>;
 			bus-num = <0>;
 			status = "disabled";
@@ -336,8 +340,8 @@
 			interrupts = <0 93 4>;
 			phys = <&usbphy0>;
 			phy-names = "usb2-phy";
-			resets = <&rst USB0_RESET>;
-			reset-names = "dwc2";
+			resets = <&rst USB0_RESET>, <&rst USB0_OCP_RESET>;
+			reset-names = "dwc2", "dwc2-ecc";
 			status = "disabled";
 		};
 
@@ -347,8 +351,8 @@
 			interrupts = <0 94 4>;
 			phys = <&usbphy0>;
 			phy-names = "usb2-phy";
-			resets = <&rst USB1_RESET>;
-			reset-names = "dwc2";
+			resets = <&rst USB1_RESET>, <&rst USB1_OCP_RESET>;
+			reset-names = "dwc2", "dwc2-ecc";
 			status = "disabled";
 		};
 

arch/arm64/boot/dts/altera/socfpga_stratix10_socdk.dts

@@ -97,3 +97,7 @@
 &uart0 {
 	status = "okay";
 };
+
+&usb0 {
+	status = "okay";
+};

arch/arm64/boot/dts/amlogic/meson-axg-s400.dts

@@ -17,6 +17,19 @@
 	};
 };
 
+&ethmac {
+	status = "okay";
+	phy-mode = "rgmii";
+	pinctrl-0 = <&eth_rgmii_y_pins>;
+	pinctrl-names = "default";
+};
+
 &uart_AO {
 	status = "okay";
 };
+
+&ir {
+	status = "okay";
+	pinctrl-0 = <&remote_input_ao_pins>;
+	pinctrl-names = "default";
+};

arch/arm64/boot/dts/amlogic/meson-axg.dtsi

@@ -7,6 +7,7 @@
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/clock/axg-clkc.h>
 
 / {
 	compatible = "amlogic,meson-axg";
@@ -113,13 +114,55 @@
 		#size-cells = <2>;
 		ranges;
 
-		cbus: cbus@ffd00000 {
+		cbus: bus@ffd00000 {
 			compatible = "simple-bus";
 			reg = <0x0 0xffd00000 0x0 0x25000>;
 			#address-cells = <2>;
 			#size-cells = <2>;
 			ranges = <0x0 0x0 0x0 0xffd00000 0x0 0x25000>;
 
+			pwm_ab: pwm@1b000 {
+				compatible = "amlogic,meson-axg-ee-pwm";
+				reg = <0x0 0x1b000 0x0 0x20>;
+				#pwm-cells = <3>;
+				status = "disabled";
+			};
+
+			pwm_cd: pwm@1a000 {
+				compatible = "amlogic,meson-axg-ee-pwm";
+				reg = <0x0 0x1a000 0x0 0x20>;
+				#pwm-cells = <3>;
+				status = "disabled";
+			};
+
+			reset: reset-controller@1004 {
+				compatible = "amlogic,meson-axg-reset";
+				reg = <0x0 0x01004 0x0 0x9c>;
+				#reset-cells = <1>;
+			};
+
+			spicc0: spi@13000 {
+				compatible = "amlogic,meson-axg-spicc";
+				reg = <0x0 0x13000 0x0 0x3c>;
+				interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clkc CLKID_SPICC0>;
+				clock-names = "core";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			spicc1: spi@15000 {
+				compatible = "amlogic,meson-axg-spicc";
+				reg = <0x0 0x15000 0x0 0x3c>;
+				interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clkc CLKID_SPICC1>;
+				clock-names = "core";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
 			uart_A: serial@24000 {
 				compatible = "amlogic,meson-gx-uart", "amlogic,meson-uart";
 				reg = <0x0 0x24000 0x0 0x14>;
@@ -135,6 +178,19 @@
 			};
 		};
 
+		ethmac: ethernet@ff3f0000 {
+			compatible = "amlogic,meson-gxbb-dwmac", "snps,dwmac";
+			reg = <0x0 0xff3f0000 0x0 0x10000
+				0x0 0xff634540 0x0 0x8>;
+			interrupts = <GIC_SPI 8 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "macirq";
+			clocks = <&clkc CLKID_ETH>,
+				 <&clkc CLKID_FCLK_DIV2>,
+				 <&clkc CLKID_MPLL2>;
+			clock-names = "stmmaceth", "clkin0", "clkin1";
+			status = "disabled";
+		};
+
 		gic: interrupt-controller@ffc01000 {
 			compatible = "arm,gic-400";
 			reg = <0x0 0xffc01000 0 0x1000>,
@@ -148,6 +204,20 @@
 			#address-cells = <0>;
 		};
 
+		hiubus: bus@ff63c000 {
+			compatible = "simple-bus";
+			reg = <0x0 0xff63c000 0x0 0x1c00>;
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges = <0x0 0x0 0x0 0xff63c000 0x0 0x1c00>;
+
+			clkc: clock-controller@0 {
+				compatible = "amlogic,axg-clkc";
+				#clock-cells = <1>;
+				reg = <0x0 0x0 0x0 0x320>;
+			};
+		};
+
 		mailbox: mailbox@ff63dc00 {
 			compatible = "amlogic,meson-gx-mhu", "amlogic,meson-gxbb-mhu";
 			reg = <0 0xff63dc00 0 0x400>;
@@ -157,6 +227,226 @@
 			#mbox-cells = <1>;
 		};
 
+		periphs: periphs@ff634000 {
+			compatible = "simple-bus";
+			reg = <0x0 0xff634000 0x0 0x2000>;
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges = <0x0 0x0 0x0 0xff634000 0x0 0x2000>;
+
+			pinctrl_periphs: pinctrl@480 {
+				compatible = "amlogic,meson-axg-periphs-pinctrl";
+				#address-cells = <2>;
+				#size-cells = <2>;
+				ranges;
+
+				gpio: bank@480 {
+					reg = <0x0 0x00480 0x0 0x40>,
+						<0x0 0x004e8 0x0 0x14>,
+						<0x0 0x00520 0x0 0x14>,
+						<0x0 0x00430 0x0 0x3c>;
+					reg-names = "mux", "pull", "pull-enable", "gpio";
+					gpio-controller;
+					#gpio-cells = <2>;
+					gpio-ranges = <&pinctrl_periphs 0 0 86>;
+				};
+
+				eth_rgmii_x_pins: eth-x-rgmii {
+					mux {
+						groups = "eth_mdio_x",
+						       "eth_mdc_x",
+						       "eth_rgmii_rx_clk_x",
+						       "eth_rx_dv_x",
+						       "eth_rxd0_x",
+						       "eth_rxd1_x",
+						       "eth_rxd2_rgmii",
+						       "eth_rxd3_rgmii",
+						       "eth_rgmii_tx_clk",
+						       "eth_txen_x",
+						       "eth_txd0_x",
+						       "eth_txd1_x",
+						       "eth_txd2_rgmii",
+						       "eth_txd3_rgmii";
+						function = "eth";
+					};
+				};
+
+				eth_rgmii_y_pins: eth-y-rgmii {
+					mux {
+						groups = "eth_mdio_y",
+						       "eth_mdc_y",
+						       "eth_rgmii_rx_clk_y",
+						       "eth_rx_dv_y",
+						       "eth_rxd0_y",
+						       "eth_rxd1_y",
+						       "eth_rxd2_rgmii",
+						       "eth_rxd3_rgmii",
+						       "eth_rgmii_tx_clk",
+						       "eth_txen_y",
+						       "eth_txd0_y",
+						       "eth_txd1_y",
+						       "eth_txd2_rgmii",
+						       "eth_txd3_rgmii";
+						function = "eth";
+					};
+				};
+
+				pwm_a_a_pins: pwm_a_a {
+					mux {
+						groups = "pwm_a_a";
+						function = "pwm_a";
+					};
+				};
+
+				pwm_a_x18_pins: pwm_a_x18 {
+					mux {
+						groups = "pwm_a_x18";
+						function = "pwm_a";
+					};
+				};
+
+				pwm_a_x20_pins: pwm_a_x20 {
+					mux {
+						groups = "pwm_a_x20";
+						function = "pwm_a";
+					};
+				};
+
+				pwm_a_z_pins: pwm_a_z {
+					mux {
+						groups = "pwm_a_z";
+						function = "pwm_a";
+					};
+				};
+
+				pwm_b_a_pins: pwm_b_a {
+					mux {
+						groups = "pwm_b_a";
+						function = "pwm_b";
+					};
+				};
+
+				pwm_b_x_pins: pwm_b_x {
+					mux {
+						groups = "pwm_b_x";
+						function = "pwm_b";
+					};
+				};
+
+				pwm_b_z_pins: pwm_b_z {
+					mux {
+						groups = "pwm_b_z";
+						function = "pwm_b";
+					};
+				};
+
+				pwm_c_a_pins: pwm_c_a {
+					mux {
+						groups = "pwm_c_a";
+						function = "pwm_c";
+					};
+				};
+
+				pwm_c_x10_pins: pwm_c_x10 {
+					mux {
+						groups = "pwm_c_x10";
+						function = "pwm_c";
+					};
+				};
+
+				pwm_c_x17_pins: pwm_c_x17 {
+					mux {
+						groups = "pwm_c_x17";
+						function = "pwm_c";
+					};
+				};
+
+				pwm_d_x11_pins: pwm_d_x11 {
+					mux {
+						groups = "pwm_d_x11";
+						function = "pwm_d";
+					};
+				};
+
+				pwm_d_x16_pins: pwm_d_x16 {
+					mux {
+						groups = "pwm_d_x16";
+						function = "pwm_d";
+					};
+				};
+
+				spi0_pins: spi0 {
+					mux {
+						groups = "spi0_miso",
+							"spi0_mosi",
+							"spi0_clk";
+						function = "spi0";
+					};
+				};
+
+				spi0_ss0_pins: spi0_ss0 {
+					mux {
+						groups = "spi0_ss0";
+						function = "spi0";
+					};
+				};
+
+				spi0_ss1_pins: spi0_ss1 {
+					mux {
+						groups = "spi0_ss1";
+						function = "spi0";
+					};
+				};
+
+				spi0_ss2_pins: spi0_ss2 {
+					mux {
+						groups = "spi0_ss2";
+						function = "spi0";
+					};
+				};
+
+
+				spi1_a_pins: spi1_a {
+					mux {
+						groups = "spi1_miso_a",
+							"spi1_mosi_a",
+							"spi1_clk_a";
+						function = "spi1";
+					};
+				};
+
+				spi1_ss0_a_pins: spi1_ss0_a {
+					mux {
+						groups = "spi1_ss0_a";
+						function = "spi1";
+					};
+				};
+
+				spi1_ss1_pins: spi1_ss1 {
+					mux {
+						groups = "spi1_ss1";
+						function = "spi1";
+					};
+				};
+
+				spi1_x_pins: spi1_x {
+					mux {
+						groups = "spi1_miso_x",
+							"spi1_mosi_x",
+							"spi1_clk_x";
+						function = "spi1";
+					};
+				};
+
+				spi1_ss0_x_pins: spi1_ss0_x {
+					mux {
+						groups = "spi1_ss0_x";
+						function = "spi1";
+					};
+				};
+			};
+		};
+
 		sram: sram@fffc0000 {
 			compatible = "amlogic,meson-axg-sram", "mmio-sram";
 			reg = <0x0 0xfffc0000 0x0 0x20000>;
@@ -175,18 +465,56 @@
 			};
 		};
 
-		aobus: aobus@ff800000 {
+		aobus: bus@ff800000 {
 			compatible = "simple-bus";
 			reg = <0x0 0xff800000 0x0 0x100000>;
 			#address-cells = <2>;
 			#size-cells = <2>;
 			ranges = <0x0 0x0 0x0 0xff800000 0x0 0x100000>;
 
+			pinctrl_aobus: pinctrl@14 {
+				compatible = "amlogic,meson-axg-aobus-pinctrl";
+				#address-cells = <2>;
+				#size-cells = <2>;
+				ranges;
+
+				gpio_ao: bank@14 {
+					reg = <0x0 0x00014 0x0 0x8>,
+						<0x0 0x0002c 0x0 0x4>,
+						<0x0 0x00024 0x0 0x8>;
+					reg-names = "mux", "pull", "gpio";
+					gpio-controller;
+					#gpio-cells = <2>;
+					gpio-ranges = <&pinctrl_aobus 0 0 15>;
+				};
+
+				remote_input_ao_pins: remote_input_ao {
+					mux {
+						groups = "remote_input_ao";
+						function = "remote_input_ao";
+					};
+				};
+			};
+
+			pwm_AO_ab: pwm@7000 {
+				compatible = "amlogic,meson-axg-ao-pwm";
+				reg = <0x0 0x07000 0x0 0x20>;
+				#pwm-cells = <3>;
+				status = "disabled";
+			};
+
+			pwm_AO_cd: pwm@2000 {
+				compatible = "amlogic,axg-ao-pwm";
+				reg = <0x0 0x02000  0x0 0x20>;
+				#pwm-cells = <3>;
+				status = "disabled";
+			};
+
 			uart_AO: serial@3000 {
 				compatible = "amlogic,meson-gx-uart", "amlogic,meson-ao-uart";
 				reg = <0x0 0x3000 0x0 0x18>;
 				interrupts = <GIC_SPI 193 IRQ_TYPE_EDGE_RISING>;
-				clocks = <&xtal>, <&xtal>, <&xtal>;
+				clocks = <&xtal>, <&clkc CLKID_CLK81>, <&xtal>;
 				clock-names = "xtal", "pclk", "baud";
 				status = "disabled";
 			};
@@ -195,10 +523,17 @@
 				compatible = "amlogic,meson-gx-uart", "amlogic,meson-ao-uart";
 				reg = <0x0 0x4000 0x0 0x18>;
 				interrupts = <GIC_SPI 197 IRQ_TYPE_EDGE_RISING>;
-				clocks = <&xtal>, <&xtal>, <&xtal>;
+				clocks = <&xtal>, <&clkc CLKID_CLK81>, <&xtal>;
 				clock-names = "xtal", "pclk", "baud";
 				status = "disabled";
 			};
+
+			ir: ir@8000 {
+				compatible = "amlogic,meson-gxbb-ir";
+				reg = <0x0 0x8000 0x0 0x20>;
+				interrupts = <GIC_SPI 196 IRQ_TYPE_EDGE_RISING>;
+				status = "disabled";
+			};
 		};
 	};
 };

arch/arm64/boot/dts/amlogic/meson-gx-p23x-q20x.dtsi

@@ -59,6 +59,18 @@
 		reg = <0x0 0x0 0x0 0x80000000>;
 	};
 
+	hdmi_5v: regulator-hdmi-5v {
+		compatible = "regulator-fixed";
+
+		regulator-name = "HDMI_5V";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+
+		gpio = <&gpio GPIOH_3 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-always-on;
+	};
+
 	vddio_boot: regulator-vddio_boot {
 		compatible = "regulator-fixed";
 		regulator-name = "VDDIO_BOOT";

arch/arm64/boot/dts/amlogic/meson-gx.dtsi

@@ -211,7 +211,7 @@
 		#size-cells = <2>;
 		ranges;
 
-		cbus: cbus@c1100000 {
+		cbus: bus@c1100000 {
 			compatible = "simple-bus";
 			reg = <0x0 0xc1100000 0x0 0x100000>;
 			#address-cells = <2>;
@@ -229,7 +229,7 @@
 
 			reset: reset-controller@4404 {
 				compatible = "amlogic,meson-gx-reset", "amlogic,meson-gxbb-reset";
-				reg = <0x0 0x04404 0x0 0x20>;
+				reg = <0x0 0x04404 0x0 0x9c>;
 				#reset-cells = <1>;
 			};
 
@@ -366,7 +366,7 @@
 			};
 		};
 
-		aobus: aobus@c8100000 {
+		aobus: bus@c8100000 {
 			compatible = "simple-bus";
 			reg = <0x0 0xc8100000 0x0 0x100000>;
 			#address-cells = <2>;
@@ -377,6 +377,12 @@
 				compatible = "amlogic,meson-gx-ao-sysctrl", "syscon", "simple-mfd";
 				reg =  <0x0 0x0 0x0 0x100>;
 
+				pwrc_vpu: power-controller-vpu {
+					compatible = "amlogic,meson-gx-pwrc-vpu";
+					#power-domain-cells = <0>;
+					amlogic,hhi-sysctrl = <&sysctrl>;
+				};
+
 				clkc_AO: clock-controller {
 					compatible = "amlogic,meson-gx-aoclkc";
 					#clock-cells = <1>;
@@ -447,13 +453,18 @@
 			};
 		};
 
-		hiubus: hiubus@c883c000 {
+		hiubus: bus@c883c000 {
 			compatible = "simple-bus";
 			reg = <0x0 0xc883c000 0x0 0x2000>;
 			#address-cells = <2>;
 			#size-cells = <2>;
 			ranges = <0x0 0x0 0x0 0xc883c000 0x0 0x2000>;
 
+			sysctrl: system-controller@0 {
+				compatible = "amlogic,meson-gx-hhi-sysctrl", "syscon", "simple-mfd";
+				reg = <0 0 0 0x400>;
+			};
+
 			mailbox: mailbox@404 {
 				compatible = "amlogic,meson-gx-mhu", "amlogic,meson-gxbb-mhu";
 				reg = <0 0x404 0 0x4c>;

arch/arm64/boot/dts/amlogic/meson-gxbb-nanopi-k2.dts

@@ -169,6 +169,7 @@
 			/* Realtek RTL8211F (0x001cc916) */
 			reg = <0>;
 			interrupt-parent = <&gpio_intc>;
+			/* MAC_INTR on GPIOZ_15 */
 			interrupts = <29 IRQ_TYPE_LEVEL_LOW>;
 		};
 	};

arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts

@@ -135,6 +135,24 @@
 		compatible = "mmc-pwrseq-emmc";
 		reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
 	};
+
+	hdmi-connector {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_connector_in: endpoint {
+				remote-endpoint = <&hdmi_tx_tmds_out>;
+			};
+		};
+	};
+};
+
+&cec_AO {
+	status = "okay";
+	pinctrl-0 = <&ao_cec_pins>;
+	pinctrl-names = "default";
+	hdmi-phandle = <&hdmi_tx>;
 };
 
 &ethmac {
@@ -156,8 +174,10 @@
 		#size-cells = <0>;
 
 		eth_phy0: ethernet-phy@0 {
+			/* Realtek RTL8211F (0x001cc916) */
 			reg = <0>;
 			interrupt-parent = <&gpio_intc>;
+			/* MAC_INTR on GPIOZ_15 */
 			interrupts = <29 IRQ_TYPE_LEVEL_LOW>;
 			eee-broken-1000t;
 		};
@@ -179,6 +199,18 @@
 	};
 };
 
+&hdmi_tx {
+	status = "okay";
+	pinctrl-0 = <&hdmi_hpd_pins>, <&hdmi_i2c_pins>;
+	pinctrl-names = "default";
+};
+
+&hdmi_tx_tmds_port {
+	hdmi_tx_tmds_out: endpoint {
+		remote-endpoint = <&hdmi_connector_in>;
+	};
+};
+
 &i2c_A {
 	status = "okay";
 	pinctrl-0 = <&i2c_a_pins>;

arch/arm64/boot/dts/amlogic/meson-gxbb-p200.dts

@@ -118,6 +118,7 @@
 			/* Micrel KSZ9031 (0x00221620) */
 			reg = <3>;
 			interrupt-parent = <&gpio_intc>;
+			/* MAC_INTR on GPIOZ_15 */
 			interrupts = <29 IRQ_TYPE_LEVEL_LOW>;
 		};
 	};

arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi

@@ -694,14 +694,55 @@
 	};
 };
 
+&pwrc_vpu {
+	resets = <&reset RESET_VIU>,
+		 <&reset RESET_VENC>,
+		 <&reset RESET_VCBUS>,
+		 <&reset RESET_BT656>,
+		 <&reset RESET_DVIN_RESET>,
+		 <&reset RESET_RDMA>,
+		 <&reset RESET_VENCI>,
+		 <&reset RESET_VENCP>,
+		 <&reset RESET_VDAC>,
+		 <&reset RESET_VDI6>,
+		 <&reset RESET_VENCL>,
+		 <&reset RESET_VID_LOCK>;
+	clocks = <&clkc CLKID_VPU>,
+	         <&clkc CLKID_VAPB>;
+	clock-names = "vpu", "vapb";
+	/*
+	 * VPU clocking is provided by two identical clock paths
+	 * VPU_0 and VPU_1 muxed to a single clock by a glitch
+	 * free mux to safely change frequency while running.
+	 * Same for VAPB but with a final gate after the glitch free mux.
+	 */
+	assigned-clocks = <&clkc CLKID_VPU_0_SEL>,
+			  <&clkc CLKID_VPU_0>,
+			  <&clkc CLKID_VPU>, /* Glitch free mux */
+			  <&clkc CLKID_VAPB_0_SEL>,
+			  <&clkc CLKID_VAPB_0>,
+			  <&clkc CLKID_VAPB_SEL>; /* Glitch free mux */
+	assigned-clock-parents = <&clkc CLKID_FCLK_DIV3>,
+				 <0>, /* Do Nothing */
+				 <&clkc CLKID_VPU_0>,
+				 <&clkc CLKID_FCLK_DIV4>,
+				 <0>, /* Do Nothing */
+				 <&clkc CLKID_VAPB_0>;
+	assigned-clock-rates = <0>, /* Do Nothing */
+			       <666666666>,
+			       <0>, /* Do Nothing */
+			       <0>, /* Do Nothing */
+			       <250000000>,
+			       <0>; /* Do Nothing */
+};
+
 &saradc {
 	compatible = "amlogic,meson-gxbb-saradc", "amlogic,meson-saradc";
 	clocks = <&xtal>,
 		 <&clkc CLKID_SAR_ADC>,
-		 <&clkc CLKID_SANA>,
 		 <&clkc CLKID_SAR_ADC_CLK>,
 		 <&clkc CLKID_SAR_ADC_SEL>;
-	clock-names = "clkin", "core", "sana", "adc_clk", "adc_sel";
+	clock-names = "clkin", "core", "adc_clk", "adc_sel";
 };
 
 &sd_emmc_a {
@@ -763,4 +804,5 @@
 
 &vpu {
 	compatible = "amlogic,meson-gxbb-vpu", "amlogic,meson-gx-vpu";
+	power-domains = <&pwrc_vpu>;
 };

arch/arm64/boot/dts/amlogic/meson-gxl-s905x-libretech-cc.dts

@@ -72,6 +72,18 @@
 		reg = <0x0 0x0 0x0 0x80000000>;
 	};
 
+	hdmi_5v: regulator-hdmi-5v {
+		compatible = "regulator-fixed";
+
+		regulator-name = "HDMI_5V";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+
+		gpio = <&gpio GPIOH_3 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-always-on;
+	};
+
 	vcc_3v3: regulator-vcc_3v3 {
 		compatible = "regulator-fixed";
 		regulator-name = "VCC_3V3";

arch/arm64/boot/dts/amlogic/meson-gxl-s905x-p212.dtsi

@@ -28,6 +28,18 @@
 		reg = <0x0 0x0 0x0 0x80000000>;
 	};
 
+	hdmi_5v: regulator-hdmi-5v {
+		compatible = "regulator-fixed";
+
+		regulator-name = "HDMI_5V";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+
+		gpio = <&gpio GPIOH_3 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-always-on;
+	};
+
 	vddio_boot: regulator-vddio_boot {
 		compatible = "regulator-fixed";
 		regulator-name = "VDDIO_BOOT";

arch/arm64/boot/dts/amlogic/meson-gxl.dtsi

@@ -644,14 +644,55 @@
 	};
 };
 
+&pwrc_vpu {
+	resets = <&reset RESET_VIU>,
+		 <&reset RESET_VENC>,
+		 <&reset RESET_VCBUS>,
+		 <&reset RESET_BT656>,
+		 <&reset RESET_DVIN_RESET>,
+		 <&reset RESET_RDMA>,
+		 <&reset RESET_VENCI>,
+		 <&reset RESET_VENCP>,
+		 <&reset RESET_VDAC>,
+		 <&reset RESET_VDI6>,
+		 <&reset RESET_VENCL>,
+		 <&reset RESET_VID_LOCK>;
+	clocks = <&clkc CLKID_VPU>,
+	         <&clkc CLKID_VAPB>;
+	clock-names = "vpu", "vapb";
+	/*
+	 * VPU clocking is provided by two identical clock paths
+	 * VPU_0 and VPU_1 muxed to a single clock by a glitch
+	 * free mux to safely change frequency while running.
+	 * Same for VAPB but with a final gate after the glitch free mux.
+	 */
+	assigned-clocks = <&clkc CLKID_VPU_0_SEL>,
+			  <&clkc CLKID_VPU_0>,
+			  <&clkc CLKID_VPU>, /* Glitch free mux */
+			  <&clkc CLKID_VAPB_0_SEL>,
+			  <&clkc CLKID_VAPB_0>,
+			  <&clkc CLKID_VAPB_SEL>; /* Glitch free mux */
+	assigned-clock-parents = <&clkc CLKID_FCLK_DIV3>,
+				 <0>, /* Do Nothing */
+				 <&clkc CLKID_VPU_0>,
+				 <&clkc CLKID_FCLK_DIV4>,
+				 <0>, /* Do Nothing */
+				 <&clkc CLKID_VAPB_0>;
+	assigned-clock-rates = <0>, /* Do Nothing */
+			       <666666666>,
+			       <0>, /* Do Nothing */
+			       <0>, /* Do Nothing */
+			       <250000000>,
+			       <0>; /* Do Nothing */
+};
+
 &saradc {
 	compatible = "amlogic,meson-gxl-saradc", "amlogic,meson-saradc";
 	clocks = <&xtal>,
 		 <&clkc CLKID_SAR_ADC>,
-		 <&clkc CLKID_SANA>,
 		 <&clkc CLKID_SAR_ADC_CLK>,
 		 <&clkc CLKID_SAR_ADC_SEL>;
-	clock-names = "clkin", "core", "sana", "adc_clk", "adc_sel";
+	clock-names = "clkin", "core", "adc_clk", "adc_sel";
 };
 
 &sd_emmc_a {
@@ -713,4 +754,5 @@
 
 &vpu {
 	compatible = "amlogic,meson-gxl-vpu", "amlogic,meson-gx-vpu";
+	power-domains = <&pwrc_vpu>;
 };

arch/arm64/boot/dts/amlogic/meson-gxm-khadas-vim2.dts

@@ -153,6 +153,18 @@
 		};
 	};
 
+	hdmi_5v: regulator-hdmi-5v {
+		compatible = "regulator-fixed";
+
+		regulator-name = "HDMI_5V";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+
+		gpio = <&gpio GPIOH_3 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-always-on;
+	};
+
 	vcc_3v3: regulator-vcc_3v3 {
 		compatible = "regulator-fixed";
 		regulator-name = "VCC_3V3";
@@ -232,6 +244,9 @@
 	external_phy: ethernet-phy@0 {
 		/* Realtek RTL8211F (0x001cc916) */
 		reg = <0>;
+		interrupt-parent = <&gpio_intc>;
+		/* MAC_INTR on GPIOZ_15 */
+		interrupts = <25 IRQ_TYPE_LEVEL_LOW>;
 	};
 };
 

arch/arm64/boot/dts/amlogic/meson-gxm-q200.dts

@@ -111,7 +111,8 @@
 		reg = <0>;
 		max-speed = <1000>;
 		interrupt-parent = <&gpio_intc>;
-		interrupts = <29 IRQ_TYPE_LEVEL_LOW>;
+		/* MAC_INTR on GPIOZ_15 */
+		interrupts = <25 IRQ_TYPE_LEVEL_LOW>;
 	};
 };
 

arch/arm64/boot/dts/exynos/exynos5433-bus.dtsi

@@ -1,12 +1,9 @@
+// SPDX-License-Identifier: GPL-2.0
 /*
  * Samsung's Exynos5433 SoC Memory interface and AMBA bus device tree source
  *
  * Copyright (c) 2016 Samsung Electronics Co., Ltd.
  * Chanwoo Choi <cw00.choi@samsung.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
  */
 
 &soc {

arch/arm64/boot/dts/exynos/exynos5433-pinctrl.dtsi

@@ -1,3 +1,4 @@
+// SPDX-License-Identifier: GPL-2.0
 /*
  * Samsung's Exynos5433 SoC pin-mux and pin-config device tree source
  *
@@ -6,10 +7,6 @@
  *
  * Samsung's Exynos5433 SoC pin-mux and pin-config options are listed as device
  * tree nodes are listed in this file.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
  */
 
 #include <dt-bindings/pinctrl/samsung.h>

arch/arm64/boot/dts/exynos/exynos5433-tm2-common.dtsi

@@ -1,3 +1,4 @@
+// SPDX-License-Identifier: GPL-2.0
 /*
  * SAMSUNG Exynos5433 TM2 board device tree source
  *
@@ -5,10 +6,6 @@
  *
  * Common device tree source file for Samsung's TM2 and TM2E boards
  * which are based on Samsung Exynos5433 SoC.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
  */
 
 /dts-v1/;
@@ -741,6 +738,19 @@
 	};
 };
 
+&hsi2c_4 {
+	status = "okay";
+
+	s3fwrn5: nfc@27 {
+		compatible = "samsung,s3fwrn5-i2c";
+		reg = <0x27>;
+		interrupt-parent = <&gpa1>;
+		interrupts = <3 IRQ_TYPE_LEVEL_HIGH>;
+		s3fwrn5,en-gpios = <&gpf1 4 GPIO_ACTIVE_HIGH>;
+		s3fwrn5,fw-gpios = <&gpj0 2 GPIO_ACTIVE_HIGH>;
+	};
+};
+
 &hsi2c_5 {
 	status = "okay";
 
@@ -756,6 +766,7 @@
 
 &hsi2c_7 {
 	status = "okay";
+	clock-frequency = <1000000>;
 
 	sii8620@39 {
 		reg = <0x39>;

arch/arm64/boot/dts/exynos/exynos5433-tm2.dts

@@ -1,3 +1,4 @@
+// SPDX-License-Identifier: GPL-2.0
 /*
  * SAMSUNG Exynos5433 TM2 board device tree source
  *
@@ -5,10 +6,6 @@
  *
  * Device tree source file for Samsung's TM2 board which is based on
  * Samsung Exynos5433 SoC.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
  */
 
 #include "exynos5433-tm2-common.dtsi"

arch/arm64/boot/dts/exynos/exynos5433-tm2e.dts

@@ -1,3 +1,4 @@
+// SPDX-License-Identifier: GPL-2.0
 /*
  * SAMSUNG Exynos5433 TM2E board device tree source
  *
@@ -5,10 +6,6 @@
  *
  * Device tree source file for Samsung's TM2E(TM2 EDGE) board which is based on
  * Samsung Exynos5433 SoC.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
  */
 
 #include "exynos5433-tm2-common.dtsi"

arch/arm64/boot/dts/exynos/exynos5433-tmu-g3d-sensor-conf.dtsi

@@ -1,11 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0
 /*
  * Device tree sources for Exynos5433 TMU sensor configuration
  *
  * Copyright (c) 2016 Jonghwa Lee <jonghwa3.lee@samsung.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
  */
 
 #include <dt-bindings/thermal/thermal_exynos.h>

arch/arm64/boot/dts/exynos/exynos5433-tmu-sensor-conf.dtsi

@@ -1,11 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0
 /*
  * Device tree sources for Exynos5433 TMU sensor configuration
  *
  * Copyright (c) 2016 Chanwoo Choi <cw00.choi@samsung.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
  */
 
 #include <dt-bindings/thermal/thermal_exynos.h>

arch/arm64/boot/dts/exynos/exynos5433-tmu.dtsi

@@ -1,11 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0
 /*
  * Device tree sources for Exynos5433 thermal zone
  *
  * Copyright (c) 2016 Chanwoo Choi <cw00.choi@samsung.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
  */
 
 #include <dt-bindings/thermal/thermal.h>

arch/arm64/boot/dts/exynos/exynos5433.dtsi

@@ -1,3 +1,4 @@
+// SPDX-License-Identifier: GPL-2.0
 /*
  * Samsung's Exynos5433 SoC device tree source
  *
@@ -10,10 +11,6 @@
  * Note: This file does not include device nodes for all the controllers in
  * Exynos5433 SoC. As device tree coverage for Exynos5433 increases,
  * additional nodes can be added to this file.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
  */
 
 #include <dt-bindings/clock/exynos5433.h>
@@ -247,6 +244,24 @@
 		#size-cells = <1>;
 		ranges = <0x0 0x0 0x0 0x18000000>;
 
+		arm_a53_pmu {
+			compatible = "arm,cortex-a53-pmu", "arm,armv8-pmuv3";
+			interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>;
+		};
+
+		arm_a57_pmu {
+			compatible = "arm,cortex-a57-pmu", "arm,armv8-pmuv3";
+			interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-affinity = <&cpu4>, <&cpu5>, <&cpu6>, <&cpu7>;
+		};
+
 		chipid@10000000 {
 			compatible = "samsung,exynos4210-chipid";
 			reg = <0x10000000 0x100>;
@@ -343,6 +358,7 @@
 			clocks = <&xxti>,
 				<&cmu_top CLK_ACLK_G2D_266>,
 				<&cmu_top CLK_ACLK_G2D_400>;
+			power-domains = <&pd_g2d>;
 		};
 
 		cmu_disp: clock-controller@13b90000 {
@@ -368,6 +384,7 @@
 				<&cmu_mif CLK_SCLK_DECON_ECLK_DISP>,
 				<&cmu_mif CLK_SCLK_DECON_TV_VCLK_DISP>,
 				<&cmu_mif CLK_ACLK_DISP_333>;
+			power-domains = <&pd_disp>;
 		};
 
 		cmu_aud: clock-controller@114c0000 {
@@ -376,6 +393,7 @@
 			#clock-cells = <1>;
 			clock-names = "oscclk", "fout_aud_pll";
 			clocks = <&xxti>, <&cmu_top CLK_FOUT_AUD_PLL>;
+			power-domains = <&pd_aud>;
 		};
 
 		cmu_bus0: clock-controller@13600000 {
@@ -412,6 +430,7 @@
 
 			clock-names = "oscclk", "aclk_g3d_400";
 			clocks = <&xxti>, <&cmu_top CLK_ACLK_G3D_400>;
+			power-domains = <&pd_g3d>;
 		};
 
 		cmu_gscl: clock-controller@13cf0000 {
@@ -425,6 +444,7 @@
 			clocks = <&xxti>,
 				<&cmu_top CLK_ACLK_GSCL_111>,
 				<&cmu_top CLK_ACLK_GSCL_333>;
+			power-domains = <&pd_gscl>;
 		};
 
 		cmu_apollo: clock-controller@11900000 {
@@ -445,7 +465,7 @@
 			clocks = <&xxti>, <&cmu_mif CLK_SCLK_BUS_PLL_ATLAS>;
 		};
 
-		cmu_mscl: clock-controller@105d0000 {
+		cmu_mscl: clock-controller@150d0000 {
 			compatible = "samsung,exynos5433-cmu-mscl";
 			reg = <0x150d0000 0x1000>;
 			#clock-cells = <1>;
@@ -456,6 +476,7 @@
 			clocks = <&xxti>,
 				<&cmu_top CLK_SCLK_JPEG_MSCL>,
 				<&cmu_top CLK_ACLK_MSCL_400>;
+			power-domains = <&pd_mscl>;
 		};
 
 		cmu_mfc: clock-controller@15280000 {
@@ -465,6 +486,7 @@
 
 			clock-names = "oscclk", "aclk_mfc_400";
 			clocks = <&xxti>, <&cmu_top CLK_ACLK_MFC_400>;
+			power-domains = <&pd_mfc>;
 		};
 
 		cmu_hevc: clock-controller@14f80000 {
@@ -474,6 +496,7 @@
 
 			clock-names = "oscclk", "aclk_hevc_400";
 			clocks = <&xxti>, <&cmu_top CLK_ACLK_HEVC_400>;
+			power-domains = <&pd_hevc>;
 		};
 
 		cmu_isp: clock-controller@146d0000 {
@@ -487,6 +510,7 @@
 			clocks = <&xxti>,
 				<&cmu_top CLK_ACLK_ISP_DIS_400>,
 				<&cmu_top CLK_ACLK_ISP_400>;
+			power-domains = <&pd_isp>;
 		};
 
 		cmu_cam0: clock-controller@120d0000 {
@@ -502,6 +526,7 @@
 				<&cmu_top CLK_ACLK_CAM0_333>,
 				<&cmu_top CLK_ACLK_CAM0_400>,
 				<&cmu_top CLK_ACLK_CAM0_552>;
+			power-domains = <&pd_cam0>;
 		};
 
 		cmu_cam1: clock-controller@145d0000 {
@@ -523,6 +548,86 @@
 				<&cmu_top CLK_ACLK_CAM1_333>,
 				<&cmu_top CLK_ACLK_CAM1_400>,
 				<&cmu_top CLK_ACLK_CAM1_552>;
+			power-domains = <&pd_cam1>;
+		};
+
+		pd_gscl: power-domain@105c4000 {
+			compatible = "samsung,exynos5433-pd";
+			reg = <0x105c4000 0x20>;
+			#power-domain-cells = <0>;
+			label = "GSCL";
+		};
+
+		pd_cam0: power-domain@105c4020 {
+			compatible = "samsung,exynos5433-pd";
+			reg = <0x105c4020 0x20>;
+			#power-domain-cells = <0>;
+			power-domains = <&pd_cam1>;
+			label = "CAM0";
+		};
+
+		pd_mscl: power-domain@105c4040 {
+			compatible = "samsung,exynos5433-pd";
+			reg = <0x105c4040 0x20>;
+			#power-domain-cells = <0>;
+			label = "MSCL";
+		};
+
+		pd_g3d: power-domain@105c4060 {
+			compatible = "samsung,exynos5433-pd";
+			reg = <0x105c4060 0x20>;
+			#power-domain-cells = <0>;
+			label = "G3D";
+		};
+
+		pd_disp: power-domain@105c4080 {
+			compatible = "samsung,exynos5433-pd";
+			reg = <0x105c4080 0x20>;
+			#power-domain-cells = <0>;
+			label = "DISP";
+		};
+
+		pd_cam1: power-domain@105c40a0 {
+			compatible = "samsung,exynos5433-pd";
+			reg = <0x105c40a0 0x20>;
+			#power-domain-cells = <0>;
+			label = "CAM1";
+		};
+
+		pd_aud: power-domain@105c40c0 {
+			compatible = "samsung,exynos5433-pd";
+			reg = <0x105c40c0 0x20>;
+			#power-domain-cells = <0>;
+			label = "AUD";
+		};
+
+		pd_g2d: power-domain@105c4120 {
+			compatible = "samsung,exynos5433-pd";
+			reg = <0x105c4120 0x20>;
+			#power-domain-cells = <0>;
+			label = "G2D";
+		};
+
+		pd_isp: power-domain@105c4140 {
+			compatible = "samsung,exynos5433-pd";
+			reg = <0x105c4140 0x20>;
+			#power-domain-cells = <0>;
+			power-domains = <&pd_cam0>;
+			label = "ISP";
+		};
+
+		pd_mfc: power-domain@105c4180 {
+			compatible = "samsung,exynos5433-pd";
+			reg = <0x105c4180 0x20>;
+			#power-domain-cells = <0>;
+			label = "MFC";
+		};
+
+		pd_hevc: power-domain@105c41c0 {
+			compatible = "samsung,exynos5433-pd";
+			reg = <0x105c41c0 0x20>;
+			#power-domain-cells = <0>;
+			label = "HEVC";
 		};
 
 		tmu_atlas0: tmu@10060000 {
@@ -637,6 +742,7 @@
 			compatible = "samsung,exynos5433-pinctrl";
 			reg = <0x114b0000 0x1000>;
 			interrupts = <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>;
+			power-domains = <&pd_aud>;
 		};
 
 		pinctrl_cpif: pinctrl@10fe0000 {
@@ -728,6 +834,7 @@
 			clock-names = "pclk", "aclk_decon", "aclk_smmu_decon0x",
 				"aclk_xiu_decon0x", "pclk_smmu_decon0x",
 				"sclk_decon_vclk", "sclk_decon_eclk";
+			power-domains = <&pd_disp>;
 			interrupt-names = "fifo", "vsync", "lcd_sys";
 			interrupts = <GIC_SPI 201 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 202 IRQ_TYPE_LEVEL_HIGH>,
@@ -765,6 +872,7 @@
 				      "aclk_xiu_decon0x", "pclk_smmu_decon0x",
 				      "sclk_decon_vclk", "sclk_decon_eclk";
 			samsung,disp-sysreg = <&syscon_disp>;
+			power-domains = <&pd_disp>;
 			interrupt-names = "fifo", "vsync", "lcd_sys";
 			interrupts = <GIC_SPI 210 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 211 IRQ_TYPE_LEVEL_HIGH>,
@@ -790,6 +898,7 @@
 					"phyclk_mipidphy0_rxclkesc0",
 					"sclk_rgb_vclk_to_dsim0",
 					"sclk_mipi";
+			power-domains = <&pd_disp>;
 			status = "disabled";
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -813,6 +922,7 @@
 			clocks = <&cmu_disp CLK_PCLK_MIC0>,
 				<&cmu_disp CLK_SCLK_RGB_VCLK_TO_MIC0>;
 			clock-names = "pclk_mic0", "sclk_rgb_vclk_to_mic0";
+			power-domains = <&pd_disp>;
 			samsung,disp-syscon = <&syscon_disp>;
 			status = "disabled";
 
@@ -881,7 +991,7 @@
 			reg = <0x145f0000 0x1038>;
 		};
 
-		gsc_0: video-scaler@13C00000 {
+		gsc_0: video-scaler@13c00000 {
 			compatible = "samsung,exynos5433-gsc";
 			reg = <0x13c00000 0x1000>;
 			interrupts = <GIC_SPI 297 IRQ_TYPE_LEVEL_HIGH>;
@@ -892,9 +1002,10 @@
 				 <&cmu_gscl CLK_ACLK_XIU_GSCLX>,
 				 <&cmu_gscl CLK_ACLK_GSCLBEND_333>;
 			iommus = <&sysmmu_gscl0>;
+			power-domains = <&pd_gscl>;
 		};
 
-		gsc_1: video-scaler@13C10000 {
+		gsc_1: video-scaler@13c10000 {
 			compatible = "samsung,exynos5433-gsc";
 			reg = <0x13c10000 0x1000>;
 			interrupts = <GIC_SPI 298 IRQ_TYPE_LEVEL_HIGH>;
@@ -905,9 +1016,10 @@
 				 <&cmu_gscl CLK_ACLK_XIU_GSCLX>,
 				 <&cmu_gscl CLK_ACLK_GSCLBEND_333>;
 			iommus = <&sysmmu_gscl1>;
+			power-domains = <&pd_gscl>;
 		};
 
-		gsc_2: video-scaler@13C20000 {
+		gsc_2: video-scaler@13c20000 {
 			compatible = "samsung,exynos5433-gsc";
 			reg = <0x13c20000 0x1000>;
 			interrupts = <GIC_SPI 299 IRQ_TYPE_LEVEL_HIGH>;
@@ -918,6 +1030,7 @@
 				 <&cmu_gscl CLK_ACLK_XIU_GSCLX>,
 				 <&cmu_gscl CLK_ACLK_GSCLBEND_333>;
 			iommus = <&sysmmu_gscl2>;
+			power-domains = <&pd_gscl>;
 		};
 
 		jpeg: codec@15020000 {
@@ -930,9 +1043,10 @@
 				 <&cmu_mscl CLK_ACLK_XIU_MSCLX>,
 				 <&cmu_mscl CLK_SCLK_JPEG>;
 			iommus = <&sysmmu_jpeg>;
+			power-domains = <&pd_mscl>;
 		};
 
-		mfc: codec@152E0000 {
+		mfc: codec@152e0000 {
 			compatible = "samsung,exynos5433-mfc";
 			reg = <0x152E0000 0x10000>;
 			interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
@@ -942,6 +1056,7 @@
 				 <&cmu_mfc CLK_ACLK_XIU_MFCX>;
 			iommus = <&sysmmu_mfc_0>, <&sysmmu_mfc_1>;
 			iommu-names = "left", "right";
+			power-domains = <&pd_mfc>;
 		};
 
 		sysmmu_decon0x: sysmmu@13a00000 {
@@ -951,6 +1066,7 @@
 			clock-names = "pclk", "aclk";
 			clocks = <&cmu_disp CLK_PCLK_SMMU_DECON0X>,
 				<&cmu_disp CLK_ACLK_SMMU_DECON0X>;
+			power-domains = <&pd_disp>;
 			#iommu-cells = <0>;
 		};
 
@@ -962,6 +1078,7 @@
 			clocks = <&cmu_disp CLK_PCLK_SMMU_DECON1X>,
 				<&cmu_disp CLK_ACLK_SMMU_DECON1X>;
 			#iommu-cells = <0>;
+			power-domains = <&pd_disp>;
 		};
 
 		sysmmu_tv0x: sysmmu@13a20000 {
@@ -972,6 +1089,7 @@
 			clocks = <&cmu_disp CLK_PCLK_SMMU_TV0X>,
 				<&cmu_disp CLK_ACLK_SMMU_TV0X>;
 			#iommu-cells = <0>;
+			power-domains = <&pd_disp>;
 		};
 
 		sysmmu_tv1x: sysmmu@13a30000 {
@@ -982,6 +1100,7 @@
 			clocks = <&cmu_disp CLK_PCLK_SMMU_TV1X>,
 				<&cmu_disp CLK_ACLK_SMMU_TV1X>;
 			#iommu-cells = <0>;
+			power-domains = <&pd_disp>;
 		};
 
 		sysmmu_gscl0: sysmmu@13c80000 {
@@ -992,6 +1111,7 @@
 			clocks = <&cmu_gscl CLK_ACLK_SMMU_GSCL0>,
 				 <&cmu_gscl CLK_PCLK_SMMU_GSCL0>;
 			#iommu-cells = <0>;
+			power-domains = <&pd_gscl>;
 		};
 
 		sysmmu_gscl1: sysmmu@13c90000 {
@@ -1002,6 +1122,7 @@
 			clocks = <&cmu_gscl CLK_ACLK_SMMU_GSCL1>,
 				 <&cmu_gscl CLK_PCLK_SMMU_GSCL1>;
 			#iommu-cells = <0>;
+			power-domains = <&pd_gscl>;
 		};
 
 		sysmmu_gscl2: sysmmu@13ca0000 {
@@ -1012,6 +1133,7 @@
 			clocks = <&cmu_gscl CLK_ACLK_SMMU_GSCL2>,
 				 <&cmu_gscl CLK_PCLK_SMMU_GSCL2>;
 			#iommu-cells = <0>;
+			power-domains = <&pd_gscl>;
 		};
 
 		sysmmu_jpeg: sysmmu@15060000 {
@@ -1022,6 +1144,7 @@
 			clocks = <&cmu_mscl CLK_PCLK_SMMU_JPEG>,
 				 <&cmu_mscl CLK_ACLK_SMMU_JPEG>;
 			#iommu-cells = <0>;
+			power-domains = <&pd_mscl>;
 		};
 
 		sysmmu_mfc_0: sysmmu@15200000 {
@@ -1032,6 +1155,7 @@
 			clocks = <&cmu_mfc CLK_PCLK_SMMU_MFC_0>,
 				 <&cmu_mfc CLK_ACLK_SMMU_MFC_0>;
 			#iommu-cells = <0>;
+			power-domains = <&pd_mfc>;
 		};
 
 		sysmmu_mfc_1: sysmmu@15210000 {
@@ -1042,6 +1166,7 @@
 			clocks = <&cmu_mfc CLK_PCLK_SMMU_MFC_1>,
 				 <&cmu_mfc CLK_ACLK_SMMU_MFC_1>;
 			#iommu-cells = <0>;
+			power-domains = <&pd_mfc>;
 		};
 
 		serial_0: serial@14c10000 {
@@ -1497,6 +1622,7 @@
 			clocks = <&cmu_aud CLK_PCLK_SFR0_CTRL>;
 			clock-names = "sfr0_ctrl";
 			samsung,pmu-syscon = <&pmu_system_controller>;
+			power-domains = <&pd_aud>;
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges;
@@ -1510,6 +1636,7 @@
 				#dma-cells = <1>;
 				#dma-channels = <8>;
 				#dma-requests = <32>;
+				power-domains = <&pd_aud>;
 			};
 
 			i2s0: i2s0@11440000 {
@@ -1526,6 +1653,7 @@
 				clock-names = "iis", "i2s_opclk0", "i2s_opclk1";
 				pinctrl-names = "default";
 				pinctrl-0 = <&i2s0_bus>;
+				power-domains = <&pd_aud>;
 				status = "disabled";
 			};
 
@@ -1538,6 +1666,7 @@
 				clock-names = "uart", "clk_uart_baud0";
 				pinctrl-names = "default";
 				pinctrl-0 = <&uart_aud_bus>;
+				power-domains = <&pd_aud>;
 				status = "disabled";
 			};
 		};

arch/arm64/boot/dts/exynos/exynos7-espresso.dts

@@ -1,13 +1,10 @@
+// SPDX-License-Identifier: GPL-2.0
 /*
  * SAMSUNG Exynos7 Espresso board device tree source
  *
  * Copyright (c) 2014 Samsung Electronics Co., Ltd.
  *		http://www.samsung.com
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
-*/
+ */
 
 /dts-v1/;
 #include "exynos7.dtsi"

arch/arm64/boot/dts/exynos/exynos7-pinctrl.dtsi

@@ -1,3 +1,4 @@
+// SPDX-License-Identifier: GPL-2.0
 /*
  * Samsung's Exynos7 SoC pin-mux and pin-config device tree source
  *
@@ -6,11 +7,7 @@
  *
  * Samsung's Exynos7 SoC pin-mux and pin-config options are listed as
  * device tree nodes in this file.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
-*/
+ */
 
 #include <dt-bindings/pinctrl/samsung.h>
 

arch/arm64/boot/dts/exynos/exynos7-tmu-sensor-conf.dtsi

@@ -1,13 +1,9 @@
+// SPDX-License-Identifier: GPL-2.0
 /*
  * Device tree sources for Exynos7 TMU sensor configuration
  *
  * Copyright (c) 2016 Samsung Electronics Co., Ltd.
  *		http://www.samsung.com
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
  */
 
 #include <dt-bindings/thermal/thermal_exynos.h>

arch/arm64/boot/dts/exynos/exynos7-trip-points.dtsi

@@ -1,13 +1,9 @@
+// SPDX-License-Identifier: GPL-2.0
 /*
  * Device tree sources for default Exynos7 thermal zone definition
  *
  * Copyright (c) 2016 Samsung Electronics Co., Ltd.
  *		http://www.samsung.com
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
  */
 
 trips {

arch/arm64/boot/dts/exynos/exynos7.dtsi

@@ -1,12 +1,9 @@
+// SPDX-License-Identifier: GPL-2.0
 /*
  * SAMSUNG EXYNOS7 SoC device tree source
  *
  * Copyright (c) 2014 Samsung Electronics Co., Ltd.
  *		http://www.samsung.com
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
  */
 
 #include <dt-bindings/clock/exynos7-clk.h>
@@ -103,7 +100,7 @@
 			#size-cells = <1>;
 			ranges;
 
-			pdma0: pdma@10E10000 {
+			pdma0: pdma@10e10000 {
 				compatible = "arm,pl330", "arm,primecell";
 				reg = <0x10E10000 0x1000>;
 				interrupts = <GIC_SPI 225 IRQ_TYPE_LEVEL_HIGH>;
@@ -114,7 +111,7 @@
 				#dma-requests = <32>;
 			};
 
-			pdma1: pdma@10EB0000 {
+			pdma1: pdma@10eb0000 {
 				compatible = "arm,pl330", "arm,primecell";
 				reg = <0x10EB0000 0x1000>;
 				interrupts = <GIC_SPI 226 IRQ_TYPE_LEVEL_HIGH>;

arch/arm64/boot/dts/freescale/fsl-ls1088a-rdb.dts

@@ -125,3 +125,11 @@
 &sata {
 	status = "okay";
 };
+
+&usb0 {
+	status = "okay";
+};
+
+&usb1 {
+	status = "okay";
+};

arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi

@@ -166,6 +166,77 @@
 			     <1 10 IRQ_TYPE_LEVEL_LOW>;/* Hypervisor PPI */
 	};
 
+	fsl_mc: fsl-mc@80c000000 {
+		compatible = "fsl,qoriq-mc";
+		reg = <0x00000008 0x0c000000 0 0x40>,	 /* MC portal base */
+		      <0x00000000 0x08340000 0 0x40000>; /* MC control reg */
+		msi-parent = <&its>;
+		#address-cells = <3>;
+		#size-cells = <1>;
+
+		/*
+		 * Region type 0x0 - MC portals
+		 * Region type 0x1 - QBMAN portals
+		 */
+		ranges = <0x0 0x0 0x0 0x8 0x0c000000 0x4000000
+			  0x1 0x0 0x0 0x8 0x18000000 0x8000000>;
+
+		dpmacs {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			dpmac1: dpmac@1 {
+				compatible = "fsl,qoriq-mc-dpmac";
+				reg = <1>;
+			};
+
+			dpmac2: dpmac@2 {
+				compatible = "fsl,qoriq-mc-dpmac";
+				reg = <2>;
+			};
+
+			dpmac3: dpmac@3 {
+				compatible = "fsl,qoriq-mc-dpmac";
+				reg = <3>;
+			};
+
+			dpmac4: dpmac@4 {
+				compatible = "fsl,qoriq-mc-dpmac";
+				reg = <4>;
+			};
+
+			dpmac5: dpmac@5 {
+				compatible = "fsl,qoriq-mc-dpmac";
+				reg = <5>;
+			};
+
+			dpmac6: dpmac@6 {
+				compatible = "fsl,qoriq-mc-dpmac";
+				reg = <6>;
+			};
+
+			dpmac7: dpmac@7 {
+				compatible = "fsl,qoriq-mc-dpmac";
+				reg = <7>;
+			};
+
+			dpmac8: dpmac@8 {
+				compatible = "fsl,qoriq-mc-dpmac";
+				reg = <8>;
+			};
+
+			dpmac9: dpmac@9 {
+				compatible = "fsl,qoriq-mc-dpmac";
+				reg = <9>;
+			};
+
+			dpmac10: dpmac@a {
+				compatible = "fsl,qoriq-mc-dpmac";
+				reg = <0xa>;
+			};
+		};
+	};
+
 	psci {
 		compatible = "arm,psci-0.2";
 		method = "smc";
@@ -191,6 +262,12 @@
 			clocks = <&sysclk>;
 		};
 
+		dcfg: dcfg@1e00000 {
+			compatible = "fsl,ls1088a-dcfg", "syscon";
+			reg = <0x0 0x1e00000 0x0 0x10000>;
+			little-endian;
+		};
+
 		tmu: tmu@1f80000 {
 			compatible = "fsl,qoriq-tmu";
 			reg = <0x0 0x1f80000 0x0 0x10000>;
@@ -394,6 +471,26 @@
 			status = "disabled";
 		};
 
+		usb0: usb3@3100000 {
+			compatible = "snps,dwc3";
+			reg = <0x0 0x3100000 0x0 0x10000>;
+			interrupts = <0 80 IRQ_TYPE_LEVEL_HIGH>;
+			dr_mode = "host";
+			snps,quirk-frame-length-adjustment = <0x20>;
+			snps,dis_rxdet_inp3_quirk;
+			status = "disabled";
+		};
+
+		usb1: usb3@3110000 {
+			compatible = "snps,dwc3";
+			reg = <0x0 0x3110000 0x0 0x10000>;
+			interrupts = <0 81 IRQ_TYPE_LEVEL_HIGH>;
+			dr_mode = "host";
+			snps,quirk-frame-length-adjustment = <0x20>;
+			snps,dis_rxdet_inp3_quirk;
+			status = "disabled";
+		};
+
 		sata: sata@3200000 {
 			compatible = "fsl,ls1088a-ahci";
 			reg = <0x0 0x3200000 0x0 0x10000>,

arch/arm64/boot/dts/freescale/fsl-ls208xa-rdb.dtsi

@@ -95,6 +95,18 @@
 			};
 		};
 
+		i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x02>;
+
+			ina220@40 {
+				compatible = "ti,ina220";
+				reg = <0x40>;
+				shunt-resistor = <500>;
+			};
+		};
+
 		i2c@3 {
 			#address-cells = <1>;
 			#size-cells = <0>;

arch/arm64/boot/dts/hisilicon/hi3660-hikey960.dts

@@ -109,6 +109,7 @@
 			label = "user_led4";
 			/* gpio_190_user_led4 */
 			gpios = <&gpio23 6 0>;
+			panic-indicator;
 			linux,default-trigger = "cpu0";
 		};
 

arch/arm64/boot/dts/hisilicon/hi3660.dtsi

@@ -61,6 +61,7 @@
 			enable-method = "psci";
 			next-level-cache = <&A53_L2>;
 			cpu-idle-states = <&CPU_SLEEP &CLUSTER_SLEEP_0>;
+			capacity-dmips-mhz = <592>;
 		};
 
 		cpu1: cpu@1 {
@@ -70,6 +71,7 @@
 			enable-method = "psci";
 			next-level-cache = <&A53_L2>;
 			cpu-idle-states = <&CPU_SLEEP &CLUSTER_SLEEP_0>;
+			capacity-dmips-mhz = <592>;
 		};
 
 		cpu2: cpu@2 {
@@ -79,6 +81,7 @@
 			enable-method = "psci";
 			next-level-cache = <&A53_L2>;
 			cpu-idle-states = <&CPU_SLEEP &CLUSTER_SLEEP_0>;
+			capacity-dmips-mhz = <592>;
 		};
 
 		cpu3: cpu@3 {
@@ -88,6 +91,7 @@
 			enable-method = "psci";
 			next-level-cache = <&A53_L2>;
 			cpu-idle-states = <&CPU_SLEEP &CLUSTER_SLEEP_0>;
+			capacity-dmips-mhz = <592>;
 		};
 
 		cpu4: cpu@100 {
@@ -101,6 +105,7 @@
 					&CPU_SLEEP
 					&CLUSTER_SLEEP_1
 			>;
+			capacity-dmips-mhz = <1024>;
 		};
 
 		cpu5: cpu@101 {
@@ -114,6 +119,7 @@
 					&CPU_SLEEP
 					&CLUSTER_SLEEP_1
 			>;
+			capacity-dmips-mhz = <1024>;
 		};
 
 		cpu6: cpu@102 {
@@ -127,6 +133,7 @@
 					&CPU_SLEEP
 					&CLUSTER_SLEEP_1
 			>;
+			capacity-dmips-mhz = <1024>;
 		};
 
 		cpu7: cpu@103 {
@@ -140,6 +147,7 @@
 					&CPU_SLEEP
 					&CLUSTER_SLEEP_1
 			>;
+			capacity-dmips-mhz = <1024>;
 		};
 
 		idle-states {
@@ -203,21 +211,25 @@
 					 IRQ_TYPE_LEVEL_HIGH)>;
 	};
 
-	pmu {
-		compatible = "arm,armv8-pmuv3";
+	a53-pmu {
+		compatible = "arm,cortex-a53-pmu";
 		interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>,
 			     <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>,
 			     <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>,
-			     <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>,
-			     <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>,
-			     <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
-			     <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
-			     <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
+			     <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>;
 		interrupt-affinity = <&cpu0>,
 				     <&cpu1>,
 				     <&cpu2>,
-				     <&cpu3>,
-				     <&cpu4>,
+				     <&cpu3>;
+	};
+
+	a73-pmu {
+		compatible = "arm,cortex-a73-pmu";
+		interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&cpu4>,
 				     <&cpu5>,
 				     <&cpu6>,
 				     <&cpu7>;

arch/arm64/boot/dts/hisilicon/hi3798cv200-poplar.dts

@@ -146,6 +146,12 @@
 	status = "okay";
 };
 
+&sd0 {
+	bus-width = <4>;
+	cap-sd-highspeed;
+	status = "okay";
+};
+
 &spi0 {
 	status = "okay";
 	label = "LS-SPI0";

arch/arm64/boot/dts/hisilicon/hi3798cv200.dtsi

@@ -192,6 +192,18 @@
 			status = "disabled";
 		};
 
+		sd0: mmc@9820000 {
+			compatible = "snps,dw-mshc";
+			reg = <0x9820000 0x10000>;
+			interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&crg HISTB_SDIO0_CIU_CLK>,
+				 <&crg HISTB_SDIO0_BIU_CLK>;
+			clock-names = "ciu", "biu";
+			resets = <&crg 0x9c 4>;
+			reset-names = "reset";
+			status = "disabled";
+		};
+
 		emmc: mmc@9830000 {
 			compatible = "snps,dw-mshc";
 			reg = <0x9830000 0x10000>;

arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts

@@ -359,6 +359,7 @@
 		user_led1 {
 			label = "user_led1";
 			gpios = <&gpio4 3 0>; /* <&gpio_user_led_4>; */
+			panic-indicator;
 			linux,default-trigger = "cpu0";
 		};
 

arch/arm64/boot/dts/marvell/armada-372x.dtsi

@@ -56,6 +56,7 @@
 			device_type = "cpu";
 			compatible = "arm,cortex-a53","arm,armv8";
 			reg = <0x1>;
+			clocks = <&nb_periph_clk 16>;
 			enable-method = "psci";
 		};
 	};

arch/arm64/boot/dts/marvell/armada-37xx.dtsi

@@ -65,6 +65,7 @@
 			device_type = "cpu";
 			compatible = "arm,cortex-a53", "arm,armv8";
 			reg = <0>;
+			clocks = <&nb_periph_clk 16>;
 			enable-method = "psci";
 		};
 	};
@@ -234,6 +235,12 @@
 				};
 			};
 
+			nb_pm: syscon@14000 {
+				compatible = "marvell,armada-3700-nb-pm",
+					     "syscon";
+				reg = <0x14000 0x60>;
+			};
+
 			pinctrl_sb: pinctrl@18800 {
 				compatible = "marvell,armada3710-sb-pinctrl",
 					     "syscon", "simple-mfd";
@@ -309,6 +316,20 @@
 				};
 			};
 
+			crypto: crypto@90000 {
+				compatible = "inside-secure,safexcel-eip97";
+				reg = <0x90000 0x20000>;
+				interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "mem", "ring0", "ring1",
+						  "ring2", "ring3", "eip";
+				clocks = <&nb_periph_clk 15>;
+			};
+
 			sdhci1: sdhci@d0000 {
 				compatible = "marvell,armada-3700-sdhci",
 					     "marvell,sdhci-xenon";

arch/arm64/boot/dts/marvell/armada-7040-db.dts

@@ -61,7 +61,13 @@
 		reg = <0x0 0x0 0x0 0x80000000>;
 	};
 
-	cpm_reg_usb3_0_vbus: cpm-usb3-0-vbus {
+	aliases {
+		ethernet0 = &cp0_eth0;
+		ethernet1 = &cp0_eth1;
+		ethernet2 = &cp0_eth2;
+	};
+
+	cp0_reg_usb3_0_vbus: cp0-usb3-0-vbus {
 		compatible = "regulator-fixed";
 		regulator-name = "usb3h0-vbus";
 		regulator-min-microvolt = <5000000>;
@@ -70,7 +76,7 @@
 		gpio = <&expander0 0 GPIO_ACTIVE_HIGH>;
 	};
 
-	cpm_reg_usb3_1_vbus: cpm-usb3-1-vbus {
+	cp0_reg_usb3_1_vbus: cp0-usb3-1-vbus {
 		compatible = "regulator-fixed";
 		regulator-name = "usb3h1-vbus";
 		regulator-min-microvolt = <5000000>;
@@ -79,14 +85,14 @@
 		gpio = <&expander0 1 GPIO_ACTIVE_HIGH>;
 	};
 
-	cpm_usb3_0_phy: cpm-usb3-0-phy {
+	cp0_usb3_0_phy: cp0-usb3-0-phy {
 		compatible = "usb-nop-xceiv";
-		vcc-supply = <&cpm_reg_usb3_0_vbus>;
+		vcc-supply = <&cp0_reg_usb3_0_vbus>;
 	};
 
-	cpm_usb3_1_phy: cpm-usb3-1-phy {
+	cp0_usb3_1_phy: cp0-usb3-1-phy {
 		compatible = "usb-nop-xceiv";
-		vcc-supply = <&cpm_reg_usb3_1_vbus>;
+		vcc-supply = <&cp0_reg_usb3_1_vbus>;
 	};
 };
 
@@ -129,11 +135,11 @@
 };
 
 
-&cpm_pcie2 {
+&cp0_pcie2 {
 	status = "okay";
 };
 
-&cpm_i2c0 {
+&cp0_i2c0 {
 	status = "okay";
 	clock-frequency = <100000>;
 
@@ -156,7 +162,7 @@
 	};
 };
 
-&cpm_nand {
+&cp0_nand {
 	/*
 	 * SPI on CPM and NAND have common pins on this board. We can
 	 * use only one at a time. To enable the NAND (whihch will
@@ -186,7 +192,7 @@
 };
 
 
-&cpm_spi1 {
+&cp0_spi1 {
 	status = "okay";
 
 	spi-flash@0 {
@@ -214,17 +220,17 @@
 	};
 };
 
-&cpm_sata0 {
+&cp0_sata0 {
 	status = "okay";
 };
 
-&cpm_usb3_0 {
-	usb-phy = <&cpm_usb3_0_phy>;
+&cp0_usb3_0 {
+	usb-phy = <&cp0_usb3_0_phy>;
 	status = "okay";
 };
 
-&cpm_usb3_1 {
-	usb-phy = <&cpm_usb3_1_phy>;
+&cp0_usb3_1 {
+	usb-phy = <&cp0_usb3_1_phy>;
 	status = "okay";
 };
 
@@ -235,14 +241,14 @@
 	non-removable;
 };
 
-&cpm_sdhci0 {
+&cp0_sdhci0 {
 	status = "okay";
 	bus-width = <4>;
 	no-1-8-v;
 	cd-gpios = <&expander0 12 GPIO_ACTIVE_LOW>;
 };
 
-&cpm_mdio {
+&cp0_mdio {
 	status = "okay";
 
 	phy0: ethernet-phy@0 {
@@ -253,28 +259,28 @@
 	};
 };
 
-&cpm_ethernet {
+&cp0_ethernet {
 	status = "okay";
 };
 
-&cpm_eth0 {
+&cp0_eth0 {
 	status = "okay";
 	/* Network PHY */
 	phy-mode = "10gbase-kr";
 	/* Generic PHY, providing serdes lanes */
-	phys = <&cpm_comphy2 0>;
+	phys = <&cp0_comphy2 0>;
 };
 
-&cpm_eth1 {
+&cp0_eth1 {
 	status = "okay";
 	/* Network PHY */
 	phy = <&phy0>;
 	phy-mode = "sgmii";
 	/* Generic PHY, providing serdes lanes */
-	phys = <&cpm_comphy0 1>;
+	phys = <&cp0_comphy0 1>;
 };
 
-&cpm_eth2 {
+&cp0_eth2 {
 	status = "okay";
 	phy = <&phy1>;
 	phy-mode = "rgmii-id";

arch/arm64/boot/dts/marvell/armada-70x0.dtsi

@@ -44,25 +44,46 @@
  * Device Tree file for the Armada 70x0 SoC
  */
 
-#include "armada-cp110-master.dtsi"
-
 / {
 	aliases {
-		gpio1 = &cpm_gpio1;
-		gpio2 = &cpm_gpio2;
+		gpio1 = &cp0_gpio1;
+		gpio2 = &cp0_gpio2;
+		spi1 = &cp0_spi0;
+		spi2 = &cp0_spi1;
 	};
 };
 
-&cpm_gpio1 {
+/*
+ * Instantiate the CP110
+ */
+#define CP110_NAME		cp0
+#define CP110_BASE		f2000000
+#define CP110_PCIE_IO_BASE	0xf9000000
+#define CP110_PCIE_MEM_BASE	0xf6000000
+#define CP110_PCIE0_BASE	f2600000
+#define CP110_PCIE1_BASE	f2620000
+#define CP110_PCIE2_BASE	f2640000
+
+#include "armada-cp110.dtsi"
+
+#undef CP110_NAME
+#undef CP110_BASE
+#undef CP110_PCIE_IO_BASE
+#undef CP110_PCIE_MEM_BASE
+#undef CP110_PCIE0_BASE
+#undef CP110_PCIE1_BASE
+#undef CP110_PCIE2_BASE
+
+&cp0_gpio1 {
 	status = "okay";
 };
 
-&cpm_gpio2 {
+&cp0_gpio2 {
 	status = "okay";
 };
 
-&cpm_syscon0 {
-	cpm_pinctrl: pinctrl {
+&cp0_syscon0 {
+	cp0_pinctrl: pinctrl {
 		compatible = "marvell,armada-7k-pinctrl";
 
 		nand_pins: nand-pins {

arch/arm64/boot/dts/marvell/armada-8020.dtsi

@@ -60,6 +60,6 @@
  * oscillator so this one is let enabled.
  */
 
-&cpm_rtc {
+&cp0_rtc {
 	status = "disabled";
 };

arch/arm64/boot/dts/marvell/armada-8040-db.dts

@@ -61,46 +61,53 @@
 		reg = <0x0 0x0 0x0 0x80000000>;
 	};
 
-	cpm_reg_usb3_0_vbus: cpm-usb3-0-vbus {
+	aliases {
+		ethernet0 = &cp0_eth0;
+		ethernet1 = &cp0_eth2;
+		ethernet2 = &cp1_eth0;
+		ethernet3 = &cp1_eth1;
+	};
+
+	cp0_reg_usb3_0_vbus: cp0-usb3-0-vbus {
 		compatible = "regulator-fixed";
-		regulator-name = "cpm-usb3h0-vbus";
+		regulator-name = "cp0-usb3h0-vbus";
 		regulator-min-microvolt = <5000000>;
 		regulator-max-microvolt = <5000000>;
 		enable-active-high;
 		gpio = <&expander0 0 GPIO_ACTIVE_HIGH>;
 	};
 
-	cpm_reg_usb3_1_vbus: cpm-usb3-1-vbus {
+	cp0_reg_usb3_1_vbus: cp0-usb3-1-vbus {
 		compatible = "regulator-fixed";
-		regulator-name = "cpm-usb3h1-vbus";
+		regulator-name = "cp0-usb3h1-vbus";
 		regulator-min-microvolt = <5000000>;
 		regulator-max-microvolt = <5000000>;
 		enable-active-high;
 		gpio = <&expander0 1 GPIO_ACTIVE_HIGH>;
 	};
 
-	cpm_usb3_0_phy: cpm-usb3-0-phy {
+	cp0_usb3_0_phy: cp0-usb3-0-phy {
 		compatible = "usb-nop-xceiv";
-		vcc-supply = <&cpm_reg_usb3_0_vbus>;
+		vcc-supply = <&cp0_reg_usb3_0_vbus>;
 	};
 
-	cpm_usb3_1_phy: cpm-usb3-1-phy {
+	cp0_usb3_1_phy: cp0-usb3-1-phy {
 		compatible = "usb-nop-xceiv";
-		vcc-supply = <&cpm_reg_usb3_1_vbus>;
+		vcc-supply = <&cp0_reg_usb3_1_vbus>;
 	};
 
-	cps_reg_usb3_0_vbus: cps-usb3-0-vbus {
+	cp1_reg_usb3_0_vbus: cp1-usb3-0-vbus {
 		compatible = "regulator-fixed";
-		regulator-name = "cps-usb3h0-vbus";
+		regulator-name = "cp1-usb3h0-vbus";
 		regulator-min-microvolt = <5000000>;
 		regulator-max-microvolt = <5000000>;
 		enable-active-high;
 		gpio = <&expander1 0 GPIO_ACTIVE_HIGH>;
 	};
 
-	cps_usb3_0_phy: cps-usb3-0-phy {
+	cp1_usb3_0_phy: cp1-usb3-0-phy {
 		compatible = "usb-nop-xceiv";
-		vcc-supply = <&cps_reg_usb3_0_vbus>;
+		vcc-supply = <&cp1_reg_usb3_0_vbus>;
 	};
 };
 
@@ -144,16 +151,16 @@
 };
 
 /* CON6 on CP0 expansion */
-&cpm_pcie0 {
+&cp0_pcie0 {
 	status = "okay";
 };
 
 /* CON5 on CP0 expansion */
-&cpm_pcie2 {
+&cp0_pcie2 {
 	status = "okay";
 };
 
-&cpm_i2c0 {
+&cp0_i2c0 {
 	status = "okay";
 	clock-frequency = <100000>;
 
@@ -178,23 +185,23 @@
 };
 
 /* CON4 on CP0 expansion */
-&cpm_sata0 {
+&cp0_sata0 {
 	status = "okay";
 };
 
 /* CON9 on CP0 expansion */
-&cpm_usb3_0 {
-	usb-phy = <&cpm_usb3_0_phy>;
+&cp0_usb3_0 {
+	usb-phy = <&cp0_usb3_0_phy>;
 	status = "okay";
 };
 
 /* CON10 on CP0 expansion */
-&cpm_usb3_1 {
-	usb-phy = <&cpm_usb3_1_phy>;
+&cp0_usb3_1 {
+	usb-phy = <&cp0_usb3_1_phy>;
 	status = "okay";
 };
 
-&cpm_mdio {
+&cp0_mdio {
 	status = "okay";
 
 	phy1: ethernet-phy@1 {
@@ -202,42 +209,42 @@
 	};
 };
 
-&cpm_ethernet {
+&cp0_ethernet {
 	status = "okay";
 };
 
-&cpm_eth0 {
+&cp0_eth0 {
 	status = "okay";
 	phy-mode = "10gbase-kr";
 };
 
-&cpm_eth2 {
+&cp0_eth2 {
 	status = "okay";
 	phy = <&phy1>;
 	phy-mode = "rgmii-id";
 };
 
 /* CON6 on CP1 expansion */
-&cps_pcie0 {
+&cp1_pcie0 {
 	status = "okay";
 };
 
 /* CON7 on CP1 expansion */
-&cps_pcie1 {
+&cp1_pcie1 {
 	status = "okay";
 };
 
 /* CON5 on CP1 expansion */
-&cps_pcie2 {
+&cp1_pcie2 {
 	status = "okay";
 };
 
-&cps_i2c0 {
+&cp1_i2c0 {
 	status = "okay";
 	clock-frequency = <100000>;
 };
 
-&cps_spi1 {
+&cp1_spi1 {
 	status = "okay";
 
 	spi-flash@0 {
@@ -268,23 +275,51 @@
 	};
 };
 
+/*
+ * Proper NAND usage will require DPR-76 to be in position 1-2, which disables
+ * MDIO signal of CP1.
+ */
+&cp1_nand {
+	num-cs = <1>;
+	pinctrl-0 = <&nand_pins>, <&nand_rb>;
+	pinctrl-names = "default";
+	nand-ecc-strength = <4>;
+	nand-ecc-step-size = <512>;
+	marvell,nand-enable-arbiter;
+	marvell,system-controller = <&cp1_syscon0>;
+	nand-on-flash-bbt;
+
+	partition@0 {
+		label = "U-Boot";
+		reg = <0 0x200000>;
+	};
+	partition@200000 {
+		label = "Linux";
+		reg = <0x200000 0xe00000>;
+	};
+	partition@1000000 {
+		label = "Filesystem";
+		reg = <0x1000000 0x3f000000>;
+	};
+};
+
 /* CON4 on CP1 expansion */
-&cps_sata0 {
+&cp1_sata0 {
 	status = "okay";
 };
 
 /* CON9 on CP1 expansion */
-&cps_usb3_0 {
-	usb-phy = <&cps_usb3_0_phy>;
+&cp1_usb3_0 {
+	usb-phy = <&cp1_usb3_0_phy>;
 	status = "okay";
 };
 
 /* CON10 on CP1 expansion */
-&cps_usb3_1 {
+&cp1_usb3_1 {
 	status = "okay";
 };
 
-&cps_mdio {
+&cp1_mdio {
 	status = "okay";
 
 	phy0: ethernet-phy@0 {
@@ -292,16 +327,16 @@
 	};
 };
 
-&cps_ethernet {
+&cp1_ethernet {
 	status = "okay";
 };
 
-&cps_eth0 {
+&cp1_eth0 {
 	status = "okay";
 	phy-mode = "10gbase-kr";
 };
 
-&cps_eth1 {
+&cp1_eth1 {
 	status = "okay";
 	phy = <&phy0>;
 	phy-mode = "rgmii-id";
@@ -313,7 +348,7 @@
 	non-removable;
 };
 
-&cpm_sdhci0 {
+&cp0_sdhci0 {
 	status = "okay";
 	bus-width = <8>;
 	non-removable;

arch/arm64/boot/dts/marvell/armada-8040-mcbin.dts

@@ -62,6 +62,12 @@
 		reg = <0x0 0x0 0x0 0x80000000>;
 	};
 
+	aliases {
+		ethernet0 = &cp0_eth0;
+		ethernet1 = &cp1_eth0;
+		ethernet2 = &cp1_eth1;
+	};
+
 	/* Regulator labels correspond with schematics */
 	v_3_3: regulator-3-3v {
 		compatible = "regulator-fixed";
@@ -84,9 +90,9 @@
 	v_5v0_usb3_hst_vbus: regulator-usb3-vbus0 {
 		compatible = "regulator-fixed";
 		enable-active-high;
-		gpio = <&cpm_gpio2 15 GPIO_ACTIVE_HIGH>;
+		gpio = <&cp0_gpio2 15 GPIO_ACTIVE_HIGH>;
 		pinctrl-names = "default";
-		pinctrl-0 = <&cpm_xhci_vbus_pins>;
+		pinctrl-0 = <&cp0_xhci_vbus_pins>;
 		regulator-name = "v_5v0_usb3_hst_vbus";
 		regulator-min-microvolt = <5000000>;
 		regulator-max-microvolt = <5000000>;
@@ -120,17 +126,17 @@
 	vqmmc-supply = <&v_vddo_h>;
 };
 
-&cpm_i2c0 {
+&cp0_i2c0 {
 	clock-frequency = <100000>;
 	pinctrl-names = "default";
-	pinctrl-0 = <&cpm_i2c0_pins>;
+	pinctrl-0 = <&cp0_i2c0_pins>;
 	status = "okay";
 };
 
-&cpm_i2c1 {
+&cp0_i2c1 {
 	clock-frequency = <100000>;
 	pinctrl-names = "default";
-	pinctrl-0 = <&cpm_i2c1_pins>;
+	pinctrl-0 = <&cp0_i2c1_pins>;
 	status = "okay";
 
 	i2c-switch@70 {
@@ -157,9 +163,9 @@
 	};
 };
 
-&cpm_mdio {
+&cp0_mdio {
 	pinctrl-names = "default";
-	pinctrl-0 = <&cpm_ge_mdio_pins>;
+	pinctrl-0 = <&cp0_ge_mdio_pins>;
 	status = "okay";
 
 	ge_phy: ethernet-phy@0 {
@@ -167,44 +173,44 @@
 	};
 };
 
-&cpm_pcie0 {
+&cp0_pcie0 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&cpm_pcie_pins>;
+	pinctrl-0 = <&cp0_pcie_pins>;
 	num-lanes = <4>;
 	num-viewport = <8>;
-	reset-gpio = <&cpm_gpio1 20 GPIO_ACTIVE_LOW>;
+	reset-gpio = <&cp0_gpio1 20 GPIO_ACTIVE_LOW>;
 	status = "okay";
 };
 
-&cpm_pinctrl {
-	cpm_ge_mdio_pins: ge-mdio-pins {
+&cp0_pinctrl {
+	cp0_ge_mdio_pins: ge-mdio-pins {
 		marvell,pins = "mpp32", "mpp34";
 		marvell,function = "ge";
 	};
-	cpm_i2c1_pins: i2c1-pins {
+	cp0_i2c1_pins: i2c1-pins {
 		marvell,pins = "mpp35", "mpp36";
 		marvell,function = "i2c1";
 	};
-	cpm_i2c0_pins: i2c0-pins {
+	cp0_i2c0_pins: i2c0-pins {
 		marvell,pins = "mpp37", "mpp38";
 		marvell,function = "i2c0";
 	};
-	cpm_xhci_vbus_pins: xhci0-vbus-pins {
+	cp0_xhci_vbus_pins: xhci0-vbus-pins {
 		marvell,pins = "mpp47";
 		marvell,function = "gpio";
 	};
-	cpm_pcie_pins: pcie-pins {
+	cp0_pcie_pins: pcie-pins {
 		marvell,pins = "mpp52";
 		marvell,function = "gpio";
 	};
-	cpm_sdhci_pins: sdhci-pins {
+	cp0_sdhci_pins: sdhci-pins {
 		marvell,pins = "mpp55", "mpp56", "mpp57", "mpp58", "mpp59",
 			       "mpp60", "mpp61";
 		marvell,function = "sdio";
 	};
 };
 
-&cpm_xmdio {
+&cp0_xmdio {
 	status = "okay";
 
 	phy0: ethernet-phy@0 {
@@ -218,83 +224,83 @@
 	};
 };
 
-&cpm_ethernet {
+&cp0_ethernet {
 	status = "okay";
 };
 
-&cpm_eth0 {
+&cp0_eth0 {
 	status = "okay";
 	/* Network PHY */
 	phy = <&phy0>;
 	phy-mode = "10gbase-kr";
 	/* Generic PHY, providing serdes lanes */
-	phys = <&cpm_comphy4 0>;
+	phys = <&cp0_comphy4 0>;
 };
 
-&cpm_sata0 {
+&cp0_sata0 {
 	/* CPM Lane 0 - U29 */
 	status = "okay";
 };
 
-&cpm_sdhci0 {
+&cp0_sdhci0 {
 	/* U6 */
 	broken-cd;
 	bus-width = <4>;
 	pinctrl-names = "default";
-	pinctrl-0 = <&cpm_sdhci_pins>;
+	pinctrl-0 = <&cp0_sdhci_pins>;
 	status = "okay";
 	vqmmc-supply = <&v_3_3>;
 };
 
-&cpm_usb3_0 {
+&cp0_usb3_0 {
 	/* J38? - USB2.0 only */
 	status = "okay";
 };
 
-&cpm_usb3_1 {
+&cp0_usb3_1 {
 	/* J38? - USB2.0 only */
 	status = "okay";
 };
 
-&cps_ethernet {
+&cp1_ethernet {
 	status = "okay";
 };
 
-&cps_eth0 {
+&cp1_eth0 {
 	status = "okay";
 	/* Network PHY */
 	phy = <&phy8>;
 	phy-mode = "10gbase-kr";
 	/* Generic PHY, providing serdes lanes */
-	phys = <&cps_comphy4 0>;
+	phys = <&cp1_comphy4 0>;
 };
 
-&cps_eth1 {
+&cp1_eth1 {
 	/* CPS Lane 0 - J5 (Gigabit RJ45) */
 	status = "okay";
 	/* Network PHY */
 	phy = <&ge_phy>;
 	phy-mode = "sgmii";
 	/* Generic PHY, providing serdes lanes */
-	phys = <&cps_comphy0 1>;
+	phys = <&cp1_comphy0 1>;
 };
 
-&cps_pinctrl {
-	cps_spi1_pins: spi1-pins {
+&cp1_pinctrl {
+	cp1_spi1_pins: spi1-pins {
 		marvell,pins = "mpp12", "mpp13", "mpp14", "mpp15", "mpp16";
 		marvell,function = "spi1";
 	};
 };
 
-&cps_sata0 {
+&cp1_sata0 {
 	/* CPS Lane 1 - U32 */
 	/* CPS Lane 3 - U31 */
 	status = "okay";
 };
 
-&cps_spi1 {
+&cp1_spi1 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&cps_spi1_pins>;
+	pinctrl-0 = <&cp1_spi1_pins>;
 	status = "okay";
 
 	spi-flash@0 {
@@ -304,7 +310,7 @@
 	};
 };
 
-&cps_usb3_0 {
+&cp1_usb3_0 {
 	/* CPS Lane 2 - CON7 */
 	usb-phy = <&usb3h0_phy>;
 	status = "okay";

arch/arm64/boot/dts/marvell/armada-8040.dtsi

@@ -59,6 +59,6 @@
  * disable it. However, the RTC clock in CP slave is connected to the
  * oscillator so this one is let enabled.
  */
-&cpm_rtc {
+&cp0_rtc {
 	status = "disabled";
 };

arch/arm64/boot/dts/marvell/armada-80x0.dtsi

@@ -44,33 +44,104 @@
  * Device Tree file for the Armada 80x0 SoC family
  */
 
-#include "armada-cp110-master.dtsi"
-#include "armada-cp110-slave.dtsi"
-
 / {
 	aliases {
-		gpio1 = &cps_gpio1;
-		gpio2 = &cpm_gpio2;
+		gpio1 = &cp1_gpio1;
+		gpio2 = &cp0_gpio2;
+		spi1 = &cp0_spi0;
+		spi2 = &cp0_spi1;
+		spi3 = &cp1_spi0;
+		spi4 = &cp1_spi1;
 	};
 };
 
+/*
+ * Instantiate the master CP110
+ */
+#define CP110_NAME		cp0
+#define CP110_BASE		f2000000
+#define CP110_PCIE_IO_BASE	0xf9000000
+#define CP110_PCIE_MEM_BASE	0xf6000000
+#define CP110_PCIE0_BASE	f2600000
+#define CP110_PCIE1_BASE	f2620000
+#define CP110_PCIE2_BASE	f2640000
+
+#include "armada-cp110.dtsi"
+
+#undef CP110_NAME
+#undef CP110_BASE
+#undef CP110_PCIE_IO_BASE
+#undef CP110_PCIE_MEM_BASE
+#undef CP110_PCIE0_BASE
+#undef CP110_PCIE1_BASE
+#undef CP110_PCIE2_BASE
+
+/*
+ * Instantiate the slave CP110
+ */
+#define CP110_NAME		cp1
+#define CP110_BASE		f4000000
+#define CP110_PCIE_IO_BASE	0xfd000000
+#define CP110_PCIE_MEM_BASE	0xfa000000
+#define CP110_PCIE0_BASE	f4600000
+#define CP110_PCIE1_BASE	f4620000
+#define CP110_PCIE2_BASE	f4640000
+
+#include "armada-cp110.dtsi"
+
+#undef CP110_NAME
+#undef CP110_BASE
+#undef CP110_PCIE_IO_BASE
+#undef CP110_PCIE_MEM_BASE
+#undef CP110_PCIE0_BASE
+#undef CP110_PCIE1_BASE
+#undef CP110_PCIE2_BASE
+
 /* The 80x0 has two CP blocks, but uses only one block from each. */
-&cps_gpio1 {
+&cp1_gpio1 {
 	status = "okay";
 };
 
-&cpm_gpio2 {
+&cp0_gpio2 {
 	status = "okay";
 };
 
-&cpm_syscon0 {
-	cpm_pinctrl: pinctrl {
+&cp0_syscon0 {
+	cp0_pinctrl: pinctrl {
 		compatible = "marvell,armada-8k-cpm-pinctrl";
 	};
 };
 
-&cps_syscon0 {
-	cps_pinctrl: pinctrl {
+&cp1_syscon0 {
+	cp1_pinctrl: pinctrl {
 		compatible = "marvell,armada-8k-cps-pinctrl";
+
+		nand_pins: nand-pins {
+			marvell,pins =
+			"mpp0", "mpp1", "mpp2", "mpp3",
+			"mpp4", "mpp5", "mpp6", "mpp7",
+			"mpp8", "mpp9", "mpp10", "mpp11",
+			"mpp15", "mpp16", "mpp17", "mpp18",
+			"mpp19", "mpp20", "mpp21", "mpp22",
+			"mpp23", "mpp24", "mpp25", "mpp26",
+			"mpp27";
+			marvell,function = "dev";
+		};
+
+		nand_rb: nand-rb {
+			marvell,pins = "mpp13", "mpp12";
+			marvell,function = "nf";
+		};
 	};
 };
+
+&cp1_crypto {
+	/*
+	 * The cryptographic engine found on the cp110
+	 * master is enabled by default at the SoC
+	 * level. Because it is not possible as of now
+	 * to enable two cryptographic engines in
+	 * parallel, disable this one by default.
+	 */
+	status = "disabled";
+};

arch/arm64/boot/dts/marvell/armada-ap806.dtsi

@@ -58,6 +58,7 @@
 		serial0 = &uart0;
 		serial1 = &uart1;
 		gpio0 = &ap_gpio;
+		spi0 = &spi0;
 	};
 
 	psci {
@@ -203,7 +204,6 @@
 				reg = <0x510600 0x50>;
 				#address-cells = <1>;
 				#size-cells = <0>;
-				cell-index = <0>;
 				interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&ap_clk 3>;
 				status = "disabled";
@@ -241,7 +241,7 @@
 
 			};
 
-			watchdog: watchdog@600000 {
+			watchdog: watchdog@610000 {
 				compatible = "arm,sbsa-gwdt";
 				reg = <0x610000 0x1000>, <0x600000 0x1000>;
 				interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
@@ -285,6 +285,12 @@
 					gpio-ranges = <&ap_pinctrl 0 0 20>;
 				};
 			};
+
+			ap_thermal: thermal@6f808c {
+				compatible = "marvell,armada-ap806-thermal";
+				reg = <0x6f808c 0x4>,
+				      <0x6f8084 0x8>;
+			};
 		};
 	};
 };

arch/arm64/boot/dts/marvell/armada-common.dtsi

@@ -0,0 +1,10 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR X11)
+/*
+ * Copyright (C) 2016 Marvell Technology Group Ltd.
+ */
+
+/* Common definitions used by Armada 7K/8K DTs */
+#define PASTER(x, y) x ## y
+#define EVALUATOR(x, y) PASTER(x, y)
+#define CP110_LABEL(name) EVALUATOR(CP110_NAME, EVALUATOR(_, name))
+#define ADDRESSIFY(addr) EVALUATOR(0x, addr)

arch/arm64/boot/dts/marvell/armada-cp110-master.dtsi

@@ -1,446 +0,0 @@
-/*
- * Copyright (C) 2016 Marvell Technology Group Ltd.
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPLv2 or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This library is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License as
- *     published by the Free Software Foundation; either version 2 of the
- *     License, or (at your option) any later version.
- *
- *     This library is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
- */
-
-/*
- * Device Tree file for Marvell Armada CP110 Master.
- */
-
-#define ICU_GRP_NSR 0x0
-
-/ {
-	cp110-master {
-		#address-cells = <2>;
-		#size-cells = <2>;
-		compatible = "simple-bus";
-		interrupt-parent = <&cpm_icu>;
-		ranges;
-
-		config-space@f2000000 {
-			#address-cells = <1>;
-			#size-cells = <1>;
-			compatible = "simple-bus";
-			ranges = <0x0 0x0 0xf2000000 0x2000000>;
-
-			cpm_ethernet: ethernet@0 {
-				compatible = "marvell,armada-7k-pp22";
-				reg = <0x0 0x100000>, <0x129000 0xb000>;
-				clocks = <&cpm_clk 1 3>, <&cpm_clk 1 9>,
-					 <&cpm_clk 1 5>, <&cpm_clk 1 18>;
-				clock-names = "pp_clk", "gop_clk",
-					      "mg_clk","axi_clk";
-				marvell,system-controller = <&cpm_syscon0>;
-				status = "disabled";
-				dma-coherent;
-
-				cpm_eth0: eth0 {
-					interrupts = <ICU_GRP_NSR 39 IRQ_TYPE_LEVEL_HIGH>,
-						     <ICU_GRP_NSR 43 IRQ_TYPE_LEVEL_HIGH>,
-						     <ICU_GRP_NSR 47 IRQ_TYPE_LEVEL_HIGH>,
-						     <ICU_GRP_NSR 51 IRQ_TYPE_LEVEL_HIGH>,
-						     <ICU_GRP_NSR 55 IRQ_TYPE_LEVEL_HIGH>,
-						     <ICU_GRP_NSR 129 IRQ_TYPE_LEVEL_HIGH>;
-					interrupt-names = "tx-cpu0", "tx-cpu1", "tx-cpu2",
-							  "tx-cpu3", "rx-shared", "link";
-					port-id = <0>;
-					gop-port-id = <0>;
-					status = "disabled";
-				};
-
-				cpm_eth1: eth1 {
-					interrupts = <ICU_GRP_NSR 40 IRQ_TYPE_LEVEL_HIGH>,
-						     <ICU_GRP_NSR 44 IRQ_TYPE_LEVEL_HIGH>,
-						     <ICU_GRP_NSR 48 IRQ_TYPE_LEVEL_HIGH>,
-						     <ICU_GRP_NSR 52 IRQ_TYPE_LEVEL_HIGH>,
-						     <ICU_GRP_NSR 56 IRQ_TYPE_LEVEL_HIGH>,
-						     <ICU_GRP_NSR 128 IRQ_TYPE_LEVEL_HIGH>;
-					interrupt-names = "tx-cpu0", "tx-cpu1", "tx-cpu2",
-							  "tx-cpu3", "rx-shared", "link";
-					port-id = <1>;
-					gop-port-id = <2>;
-					status = "disabled";
-				};
-
-				cpm_eth2: eth2 {
-					interrupts = <ICU_GRP_NSR 41 IRQ_TYPE_LEVEL_HIGH>,
-						     <ICU_GRP_NSR 45 IRQ_TYPE_LEVEL_HIGH>,
-						     <ICU_GRP_NSR 49 IRQ_TYPE_LEVEL_HIGH>,
-						     <ICU_GRP_NSR 53 IRQ_TYPE_LEVEL_HIGH>,
-						     <ICU_GRP_NSR 57 IRQ_TYPE_LEVEL_HIGH>,
-						     <ICU_GRP_NSR 127 IRQ_TYPE_LEVEL_HIGH>;
-					interrupt-names = "tx-cpu0", "tx-cpu1", "tx-cpu2",
-							  "tx-cpu3", "rx-shared", "link";
-					port-id = <2>;
-					gop-port-id = <3>;
-					status = "disabled";
-				};
-			};
-
-			cpm_comphy: phy@120000 {
-				compatible = "marvell,comphy-cp110";
-				reg = <0x120000 0x6000>;
-				marvell,system-controller = <&cpm_syscon0>;
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				cpm_comphy0: phy@0 {
-					reg = <0>;
-					#phy-cells = <1>;
-				};
-
-				cpm_comphy1: phy@1 {
-					reg = <1>;
-					#phy-cells = <1>;
-				};
-
-				cpm_comphy2: phy@2 {
-					reg = <2>;
-					#phy-cells = <1>;
-				};
-
-				cpm_comphy3: phy@3 {
-					reg = <3>;
-					#phy-cells = <1>;
-				};
-
-				cpm_comphy4: phy@4 {
-					reg = <4>;
-					#phy-cells = <1>;
-				};
-
-				cpm_comphy5: phy@5 {
-					reg = <5>;
-					#phy-cells = <1>;
-				};
-			};
-
-			cpm_mdio: mdio@12a200 {
-				#address-cells = <1>;
-				#size-cells = <0>;
-				compatible = "marvell,orion-mdio";
-				reg = <0x12a200 0x10>;
-				clocks = <&cpm_clk 1 9>, <&cpm_clk 1 5>,
-					 <&cpm_clk 1 6>, <&cpm_clk 1 18>;
-				status = "disabled";
-			};
-
-			cpm_xmdio: mdio@12a600 {
-				#address-cells = <1>;
-				#size-cells = <0>;
-				compatible = "marvell,xmdio";
-				reg = <0x12a600 0x10>;
-				status = "disabled";
-			};
-
-			cpm_icu: interrupt-controller@1e0000 {
-				compatible = "marvell,cp110-icu";
-				reg = <0x1e0000 0x10>;
-				#interrupt-cells = <3>;
-				interrupt-controller;
-				msi-parent = <&gicp>;
-			};
-
-			cpm_rtc: rtc@284000 {
-				compatible = "marvell,armada-8k-rtc";
-				reg = <0x284000 0x20>, <0x284080 0x24>;
-				reg-names = "rtc", "rtc-soc";
-				interrupts = <ICU_GRP_NSR 77 IRQ_TYPE_LEVEL_HIGH>;
-			};
-
-			cpm_syscon0: system-controller@440000 {
-				compatible = "syscon", "simple-mfd";
-				reg = <0x440000 0x2000>;
-
-				cpm_clk: clock {
-					compatible = "marvell,cp110-clock";
-					#clock-cells = <2>;
-				};
-
-				cpm_gpio1: gpio@100 {
-					compatible = "marvell,armada-8k-gpio";
-					offset = <0x100>;
-					ngpios = <32>;
-					gpio-controller;
-					#gpio-cells = <2>;
-					gpio-ranges = <&cpm_pinctrl 0 0 32>;
-					interrupt-controller;
-					interrupts = <ICU_GRP_NSR 86 IRQ_TYPE_LEVEL_HIGH>,
-						     <ICU_GRP_NSR 85 IRQ_TYPE_LEVEL_HIGH>,
-						     <ICU_GRP_NSR 84 IRQ_TYPE_LEVEL_HIGH>,
-						     <ICU_GRP_NSR 83 IRQ_TYPE_LEVEL_HIGH>;
-					status = "disabled";
-				};
-
-				cpm_gpio2: gpio@140 {
-					compatible = "marvell,armada-8k-gpio";
-					offset = <0x140>;
-					ngpios = <31>;
-					gpio-controller;
-					#gpio-cells = <2>;
-					gpio-ranges = <&cpm_pinctrl 0 32 31>;
-					interrupt-controller;
-					interrupts = <ICU_GRP_NSR 82 IRQ_TYPE_LEVEL_HIGH>,
-						     <ICU_GRP_NSR 81 IRQ_TYPE_LEVEL_HIGH>,
-						     <ICU_GRP_NSR 80 IRQ_TYPE_LEVEL_HIGH>,
-						     <ICU_GRP_NSR 79 IRQ_TYPE_LEVEL_HIGH>;
-					status = "disabled";
-				};
-			};
-
-			cpm_usb3_0: usb3@500000 {
-				compatible = "marvell,armada-8k-xhci",
-					     "generic-xhci";
-				reg = <0x500000 0x4000>;
-				dma-coherent;
-				interrupts = <ICU_GRP_NSR 106 IRQ_TYPE_LEVEL_HIGH>;
-				clocks = <&cpm_clk 1 22>;
-				status = "disabled";
-			};
-
-			cpm_usb3_1: usb3@510000 {
-				compatible = "marvell,armada-8k-xhci",
-					     "generic-xhci";
-				reg = <0x510000 0x4000>;
-				dma-coherent;
-				interrupts = <ICU_GRP_NSR 105 IRQ_TYPE_LEVEL_HIGH>;
-				clocks = <&cpm_clk 1 23>;
-				status = "disabled";
-			};
-
-			cpm_sata0: sata@540000 {
-				compatible = "marvell,armada-8k-ahci",
-					     "generic-ahci";
-				reg = <0x540000 0x30000>;
-				interrupts = <ICU_GRP_NSR 107 IRQ_TYPE_LEVEL_HIGH>;
-				clocks = <&cpm_clk 1 15>;
-				status = "disabled";
-			};
-
-			cpm_xor0: xor@6a0000 {
-				compatible = "marvell,armada-7k-xor", "marvell,xor-v2";
-				reg = <0x6a0000 0x1000>,
-				      <0x6b0000 0x1000>;
-				dma-coherent;
-				msi-parent = <&gic_v2m0>;
-				clocks = <&cpm_clk 1 8>;
-			};
-
-			cpm_xor1: xor@6c0000 {
-				compatible = "marvell,armada-7k-xor", "marvell,xor-v2";
-				reg = <0x6c0000 0x1000>,
-				      <0x6d0000 0x1000>;
-				dma-coherent;
-				msi-parent = <&gic_v2m0>;
-				clocks = <&cpm_clk 1 7>;
-			};
-
-			cpm_spi0: spi@700600 {
-				compatible = "marvell,armada-380-spi";
-				reg = <0x700600 0x50>;
-				#address-cells = <0x1>;
-				#size-cells = <0x0>;
-				cell-index = <1>;
-				clocks = <&cpm_clk 1 21>;
-				status = "disabled";
-			};
-
-			cpm_spi1: spi@700680 {
-				compatible = "marvell,armada-380-spi";
-				reg = <0x700680 0x50>;
-				#address-cells = <1>;
-				#size-cells = <0>;
-				cell-index = <2>;
-				clocks = <&cpm_clk 1 21>;
-				status = "disabled";
-			};
-
-			cpm_i2c0: i2c@701000 {
-				compatible = "marvell,mv78230-i2c";
-				reg = <0x701000 0x20>;
-				#address-cells = <1>;
-				#size-cells = <0>;
-				interrupts = <ICU_GRP_NSR 120 IRQ_TYPE_LEVEL_HIGH>;
-				clocks = <&cpm_clk 1 21>;
-				status = "disabled";
-			};
-
-			cpm_i2c1: i2c@701100 {
-				compatible = "marvell,mv78230-i2c";
-				reg = <0x701100 0x20>;
-				#address-cells = <1>;
-				#size-cells = <0>;
-				interrupts = <ICU_GRP_NSR 121 IRQ_TYPE_LEVEL_HIGH>;
-				clocks = <&cpm_clk 1 21>;
-				status = "disabled";
-			};
-
-			cpm_nand: nand@720000 {
-				/*
-				 * Due to the limiation of the pin available
-				 * this controller is only usable on the CPM
-				 * for A7K and on the CPS for A8K.
-				 */
-				compatible = "marvell,armada-8k-nand",
-					     "marvell,armada370-nand";
-				reg = <0x720000 0x54>;
-				#address-cells = <1>;
-				#size-cells = <1>;
-				interrupts = <ICU_GRP_NSR 115 IRQ_TYPE_LEVEL_HIGH>;
-				clocks = <&cpm_clk 1 2>;
-				marvell,system-controller = <&cpm_syscon0>;
-				status = "disabled";
-			};
-
-			cpm_trng: trng@760000 {
-				compatible = "marvell,armada-8k-rng", "inside-secure,safexcel-eip76";
-				reg = <0x760000 0x7d>;
-				interrupts = <ICU_GRP_NSR 95 IRQ_TYPE_LEVEL_HIGH>;
-				clocks = <&cpm_clk 1 25>;
-				status = "okay";
-			};
-
-			cpm_sdhci0: sdhci@780000 {
-				compatible = "marvell,armada-cp110-sdhci";
-				reg = <0x780000 0x300>;
-				interrupts = <ICU_GRP_NSR 27 IRQ_TYPE_LEVEL_HIGH>;
-				clock-names = "core","axi";
-				clocks = <&cpm_clk 1 4>, <&cpm_clk 1 18>;
-				dma-coherent;
-				status = "disabled";
-			};
-
-			cpm_crypto: crypto@800000 {
-				compatible = "inside-secure,safexcel-eip197";
-				reg = <0x800000 0x200000>;
-				interrupts = <ICU_GRP_NSR 87 IRQ_TYPE_LEVEL_HIGH>,
-					     <ICU_GRP_NSR 88 IRQ_TYPE_LEVEL_HIGH>,
-					     <ICU_GRP_NSR 89 IRQ_TYPE_LEVEL_HIGH>,
-					     <ICU_GRP_NSR 90 IRQ_TYPE_LEVEL_HIGH>,
-					     <ICU_GRP_NSR 91 IRQ_TYPE_LEVEL_HIGH>,
-					     <ICU_GRP_NSR 92 IRQ_TYPE_LEVEL_HIGH>;
-				interrupt-names = "mem", "ring0", "ring1",
-				"ring2", "ring3", "eip";
-				clocks = <&cpm_clk 1 26>;
-				dma-coherent;
-			};
-		};
-
-		cpm_pcie0: pcie@f2600000 {
-			compatible = "marvell,armada8k-pcie", "snps,dw-pcie";
-			reg = <0 0xf2600000 0 0x10000>,
-			      <0 0xf6f00000 0 0x80000>;
-			reg-names = "ctrl", "config";
-			#address-cells = <3>;
-			#size-cells = <2>;
-			#interrupt-cells = <1>;
-			device_type = "pci";
-			dma-coherent;
-			msi-parent = <&gic_v2m0>;
-
-			bus-range = <0 0xff>;
-			ranges =
-				/* downstream I/O */
-				<0x81000000 0 0xf9000000 0  0xf9000000 0 0x10000
-				/* non-prefetchable memory */
-				0x82000000 0 0xf6000000 0  0xf6000000 0 0xf00000>;
-			interrupt-map-mask = <0 0 0 0>;
-			interrupt-map = <0 0 0 0 &cpm_icu ICU_GRP_NSR 22 IRQ_TYPE_LEVEL_HIGH>;
-			interrupts = <ICU_GRP_NSR 22 IRQ_TYPE_LEVEL_HIGH>;
-			num-lanes = <1>;
-			clocks = <&cpm_clk 1 13>;
-			status = "disabled";
-		};
-
-		cpm_pcie1: pcie@f2620000 {
-			compatible = "marvell,armada8k-pcie", "snps,dw-pcie";
-			reg = <0 0xf2620000 0 0x10000>,
-			      <0 0xf7f00000 0 0x80000>;
-			reg-names = "ctrl", "config";
-			#address-cells = <3>;
-			#size-cells = <2>;
-			#interrupt-cells = <1>;
-			device_type = "pci";
-			dma-coherent;
-			msi-parent = <&gic_v2m0>;
-
-			bus-range = <0 0xff>;
-			ranges =
-				/* downstream I/O */
-				<0x81000000 0 0xf9010000 0  0xf9010000 0 0x10000
-				/* non-prefetchable memory */
-				0x82000000 0 0xf7000000 0  0xf7000000 0 0xf00000>;
-			interrupt-map-mask = <0 0 0 0>;
-			interrupt-map = <0 0 0 0 &cpm_icu ICU_GRP_NSR 24 IRQ_TYPE_LEVEL_HIGH>;
-			interrupts = <ICU_GRP_NSR 24 IRQ_TYPE_LEVEL_HIGH>;
-
-			num-lanes = <1>;
-			clocks = <&cpm_clk 1 11>;
-			status = "disabled";
-		};
-
-		cpm_pcie2: pcie@f2640000 {
-			compatible = "marvell,armada8k-pcie", "snps,dw-pcie";
-			reg = <0 0xf2640000 0 0x10000>,
-			      <0 0xf8f00000 0 0x80000>;
-			reg-names = "ctrl", "config";
-			#address-cells = <3>;
-			#size-cells = <2>;
-			#interrupt-cells = <1>;
-			device_type = "pci";
-			dma-coherent;
-			msi-parent = <&gic_v2m0>;
-
-			bus-range = <0 0xff>;
-			ranges =
-				/* downstream I/O */
-				<0x81000000 0 0xf9020000 0  0xf9020000 0 0x10000
-				/* non-prefetchable memory */
-				0x82000000 0 0xf8000000 0  0xf8000000 0 0xf00000>;
-			interrupt-map-mask = <0 0 0 0>;
-			interrupt-map = <0 0 0 0 &cpm_icu ICU_GRP_NSR 23 IRQ_TYPE_LEVEL_HIGH>;
-			interrupts = <ICU_GRP_NSR 23 IRQ_TYPE_LEVEL_HIGH>;
-
-			num-lanes = <1>;
-			clocks = <&cpm_clk 1 12>;
-			status = "disabled";
-		};
-	};
-};

arch/arm64/boot/dts/marvell/armada-cp110-slave.dtsi

@@ -1,444 +0,0 @@
-/*
- * Copyright (C) 2016 Marvell Technology Group Ltd.
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPLv2 or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This library is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License as
- *     published by the Free Software Foundation; either version 2 of the
- *     License, or (at your option) any later version.
- *
- *     This library is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
- */
-
-/*
- * Device Tree file for Marvell Armada CP110 Slave.
- */
-
-#define ICU_GRP_NSR 0x0
-
-/ {
-	cp110-slave {
-		#address-cells = <2>;
-		#size-cells = <2>;
-		compatible = "simple-bus";
-		interrupt-parent = <&cps_icu>;
-		ranges;
-
-		config-space@f4000000 {
-			#address-cells = <1>;
-			#size-cells = <1>;
-			compatible = "simple-bus";
-			ranges = <0x0 0x0 0xf4000000 0x2000000>;
-
-			cps_ethernet: ethernet@0 {
-				compatible = "marvell,armada-7k-pp22";
-				reg = <0x0 0x100000>, <0x129000 0xb000>;
-				clocks = <&cps_clk 1 3>, <&cps_clk 1 9>,
-					 <&cps_clk 1 5>, <&cps_clk 1 18>;
-				clock-names = "pp_clk", "gop_clk",
-					      "mg_clk", "axi_clk";
-				marvell,system-controller = <&cps_syscon0>;
-				status = "disabled";
-				dma-coherent;
-
-				cps_eth0: eth0 {
-					interrupts = <ICU_GRP_NSR 39 IRQ_TYPE_LEVEL_HIGH>,
-						     <ICU_GRP_NSR 43 IRQ_TYPE_LEVEL_HIGH>,
-						     <ICU_GRP_NSR 47 IRQ_TYPE_LEVEL_HIGH>,
-						     <ICU_GRP_NSR 51 IRQ_TYPE_LEVEL_HIGH>,
-						     <ICU_GRP_NSR 55 IRQ_TYPE_LEVEL_HIGH>,
-						     <ICU_GRP_NSR 129 IRQ_TYPE_LEVEL_HIGH>;
-					interrupt-names = "tx-cpu0", "tx-cpu1", "tx-cpu2",
-							  "tx-cpu3", "rx-shared", "link";
-					port-id = <0>;
-					gop-port-id = <0>;
-					status = "disabled";
-				};
-
-				cps_eth1: eth1 {
-					interrupts = <ICU_GRP_NSR 40 IRQ_TYPE_LEVEL_HIGH>,
-						     <ICU_GRP_NSR 44 IRQ_TYPE_LEVEL_HIGH>,
-						     <ICU_GRP_NSR 48 IRQ_TYPE_LEVEL_HIGH>,
-						     <ICU_GRP_NSR 52 IRQ_TYPE_LEVEL_HIGH>,
-						     <ICU_GRP_NSR 56 IRQ_TYPE_LEVEL_HIGH>,
-						     <ICU_GRP_NSR 128 IRQ_TYPE_LEVEL_HIGH>;
-					interrupt-names = "tx-cpu0", "tx-cpu1", "tx-cpu2",
-							  "tx-cpu3", "rx-shared", "link";
-					port-id = <1>;
-					gop-port-id = <2>;
-					status = "disabled";
-				};
-
-				cps_eth2: eth2 {
-					interrupts = <ICU_GRP_NSR 41 IRQ_TYPE_LEVEL_HIGH>,
-						     <ICU_GRP_NSR 45 IRQ_TYPE_LEVEL_HIGH>,
-						     <ICU_GRP_NSR 49 IRQ_TYPE_LEVEL_HIGH>,
-						     <ICU_GRP_NSR 53 IRQ_TYPE_LEVEL_HIGH>,
-						     <ICU_GRP_NSR 57 IRQ_TYPE_LEVEL_HIGH>,
-						     <ICU_GRP_NSR 127 IRQ_TYPE_LEVEL_HIGH>;
-					interrupt-names = "tx-cpu0", "tx-cpu1", "tx-cpu2",
-							  "tx-cpu3", "rx-shared", "link";
-					port-id = <2>;
-					gop-port-id = <3>;
-					status = "disabled";
-				};
-			};
-
-			cps_comphy: phy@120000 {
-				compatible = "marvell,comphy-cp110";
-				reg = <0x120000 0x6000>;
-				marvell,system-controller = <&cps_syscon0>;
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				cps_comphy0: phy@0 {
-					reg = <0>;
-					#phy-cells = <1>;
-				};
-
-				cps_comphy1: phy@1 {
-					reg = <1>;
-					#phy-cells = <1>;
-				};
-
-				cps_comphy2: phy@2 {
-					reg = <2>;
-					#phy-cells = <1>;
-				};
-
-				cps_comphy3: phy@3 {
-					reg = <3>;
-					#phy-cells = <1>;
-				};
-
-				cps_comphy4: phy@4 {
-					reg = <4>;
-					#phy-cells = <1>;
-				};
-
-				cps_comphy5: phy@5 {
-					reg = <5>;
-					#phy-cells = <1>;
-				};
-			};
-
-			cps_mdio: mdio@12a200 {
-				#address-cells = <1>;
-				#size-cells = <0>;
-				compatible = "marvell,orion-mdio";
-				reg = <0x12a200 0x10>;
-				clocks = <&cps_clk 1 9>, <&cps_clk 1 5>,
-					 <&cps_clk 1 6>, <&cps_clk 1 18>;
-				status = "disabled";
-			};
-
-			cps_xmdio: mdio@12a600 {
-				#address-cells = <1>;
-				#size-cells = <0>;
-				compatible = "marvell,xmdio";
-				reg = <0x12a600 0x10>;
-				status = "disabled";
-			};
-
-			cps_icu: interrupt-controller@1e0000 {
-				compatible = "marvell,cp110-icu";
-				reg = <0x1e0000 0x10>;
-				#interrupt-cells = <3>;
-				interrupt-controller;
-				msi-parent = <&gicp>;
-			};
-
-			cps_rtc: rtc@284000 {
-				compatible = "marvell,armada-8k-rtc";
-				reg = <0x284000 0x20>, <0x284080 0x24>;
-				reg-names = "rtc", "rtc-soc";
-				interrupts = <ICU_GRP_NSR 77 IRQ_TYPE_LEVEL_HIGH>;
-			};
-
-			cps_syscon0: system-controller@440000 {
-				compatible = "syscon", "simple-mfd";
-				reg = <0x440000 0x2000>;
-
-				cps_clk: clock {
-					compatible = "marvell,cp110-clock";
-					#clock-cells = <2>;
-				};
-
-				cps_gpio1: gpio@100 {
-					compatible = "marvell,armada-8k-gpio";
-					offset = <0x100>;
-					ngpios = <32>;
-					gpio-controller;
-					#gpio-cells = <2>;
-					gpio-ranges = <&cps_pinctrl 0 0 32>;
-					interrupt-controller;
-					interrupts = <ICU_GRP_NSR 86 IRQ_TYPE_LEVEL_HIGH>,
-						     <ICU_GRP_NSR 85 IRQ_TYPE_LEVEL_HIGH>,
-						     <ICU_GRP_NSR 84 IRQ_TYPE_LEVEL_HIGH>,
-						     <ICU_GRP_NSR 83 IRQ_TYPE_LEVEL_HIGH>;
-					status = "disabled";
-				};
-
-				cps_gpio2: gpio@140 {
-					compatible = "marvell,armada-8k-gpio";
-					offset = <0x140>;
-					ngpios = <31>;
-					gpio-controller;
-					#gpio-cells = <2>;
-					gpio-ranges = <&cps_pinctrl 0 32 31>;
-					interrupt-controller;
-					interrupts = <ICU_GRP_NSR 82 IRQ_TYPE_LEVEL_HIGH>,
-						     <ICU_GRP_NSR 81 IRQ_TYPE_LEVEL_HIGH>,
-						     <ICU_GRP_NSR 80 IRQ_TYPE_LEVEL_HIGH>,
-						     <ICU_GRP_NSR 79 IRQ_TYPE_LEVEL_HIGH>;
-					status = "disabled";
-				};
-
-			};
-
-			cps_usb3_0: usb3@500000 {
-				compatible = "marvell,armada-8k-xhci",
-					     "generic-xhci";
-				reg = <0x500000 0x4000>;
-				dma-coherent;
-				interrupts = <ICU_GRP_NSR 106 IRQ_TYPE_LEVEL_HIGH>;
-				clocks = <&cps_clk 1 22>;
-				status = "disabled";
-			};
-
-			cps_usb3_1: usb3@510000 {
-				compatible = "marvell,armada-8k-xhci",
-					     "generic-xhci";
-				reg = <0x510000 0x4000>;
-				dma-coherent;
-				interrupts = <ICU_GRP_NSR 105 IRQ_TYPE_LEVEL_HIGH>;
-				clocks = <&cps_clk 1 23>;
-				status = "disabled";
-			};
-
-			cps_sata0: sata@540000 {
-				compatible = "marvell,armada-8k-ahci",
-					     "generic-ahci";
-				reg = <0x540000 0x30000>;
-				interrupts = <ICU_GRP_NSR 107 IRQ_TYPE_LEVEL_HIGH>;
-				clocks = <&cps_clk 1 15>;
-				status = "disabled";
-			};
-
-			cps_xor0: xor@6a0000 {
-				compatible = "marvell,armada-7k-xor", "marvell,xor-v2";
-				reg = <0x6a0000 0x1000>,
-				      <0x6b0000 0x1000>;
-				dma-coherent;
-				msi-parent = <&gic_v2m0>;
-				clocks = <&cps_clk 1 8>;
-			};
-
-			cps_xor1: xor@6c0000 {
-				compatible = "marvell,armada-7k-xor", "marvell,xor-v2";
-				reg = <0x6c0000 0x1000>,
-				      <0x6d0000 0x1000>;
-				dma-coherent;
-				msi-parent = <&gic_v2m0>;
-				clocks = <&cps_clk 1 7>;
-			};
-
-			cps_spi0: spi@700600 {
-				compatible = "marvell,armada-380-spi";
-				reg = <0x700600 0x50>;
-				#address-cells = <0x1>;
-				#size-cells = <0x0>;
-				cell-index = <3>;
-				clocks = <&cps_clk 1 21>;
-				status = "disabled";
-			};
-
-			cps_spi1: spi@700680 {
-				compatible = "marvell,armada-380-spi";
-				reg = <0x700680 0x50>;
-				#address-cells = <1>;
-				#size-cells = <0>;
-				cell-index = <4>;
-				clocks = <&cps_clk 1 21>;
-				status = "disabled";
-			};
-
-			cps_i2c0: i2c@701000 {
-				compatible = "marvell,mv78230-i2c";
-				reg = <0x701000 0x20>;
-				#address-cells = <1>;
-				#size-cells = <0>;
-				interrupts = <ICU_GRP_NSR 120 IRQ_TYPE_LEVEL_HIGH>;
-				clocks = <&cps_clk 1 21>;
-				status = "disabled";
-			};
-
-			cps_i2c1: i2c@701100 {
-				compatible = "marvell,mv78230-i2c";
-				reg = <0x701100 0x20>;
-				#address-cells = <1>;
-				#size-cells = <0>;
-				interrupts = <ICU_GRP_NSR 121 IRQ_TYPE_LEVEL_HIGH>;
-				clocks = <&cps_clk 1 21>;
-				status = "disabled";
-			};
-
-			cps_nand: nand@720000 {
-				/*
-				 * Due to the limiation of the pin available
-				 * this controller is only usable on the CPM
-				 * for A7K and on the CPS for A8K.
-				 */
-				compatible = "marvell,armada370-nand",
-					     "marvell,armada370-nand";
-				reg = <0x720000 0x54>;
-				#address-cells = <1>;
-				#size-cells = <1>;
-				interrupts = <ICU_GRP_NSR 115 IRQ_TYPE_LEVEL_HIGH>;
-				clocks = <&cps_clk 1 2>;
-				status = "disabled";
-			};
-
-			cps_trng: trng@760000 {
-				compatible = "marvell,armada-8k-rng", "inside-secure,safexcel-eip76";
-				reg = <0x760000 0x7d>;
-				interrupts = <ICU_GRP_NSR 95 IRQ_TYPE_LEVEL_HIGH>;
-				clocks = <&cps_clk 1 25>;
-				status = "okay";
-			};
-
-			cps_crypto: crypto@800000 {
-				compatible = "inside-secure,safexcel-eip197";
-				reg = <0x800000 0x200000>;
-				interrupts = <ICU_GRP_NSR 87 IRQ_TYPE_LEVEL_HIGH>,
-					     <ICU_GRP_NSR 88 IRQ_TYPE_LEVEL_HIGH>,
-					     <ICU_GRP_NSR 89 IRQ_TYPE_LEVEL_HIGH>,
-					     <ICU_GRP_NSR 90 IRQ_TYPE_LEVEL_HIGH>,
-					     <ICU_GRP_NSR 91 IRQ_TYPE_LEVEL_HIGH>,
-					     <ICU_GRP_NSR 92 IRQ_TYPE_LEVEL_HIGH>;
-				interrupt-names = "mem", "ring0", "ring1",
-						  "ring2", "ring3", "eip";
-				clocks = <&cps_clk 1 26>;
-				dma-coherent;
-				/*
-				 * The cryptographic engine found on the cp110
-				 * master is enabled by default at the SoC
-				 * level. Because it is not possible as of now
-				 * to enable two cryptographic engines in
-				 * parallel, disable this one by default.
-				 */
-				status = "disabled";
-			};
-		};
-
-		cps_pcie0: pcie@f4600000 {
-			compatible = "marvell,armada8k-pcie", "snps,dw-pcie";
-			reg = <0 0xf4600000 0 0x10000>,
-			      <0 0xfaf00000 0 0x80000>;
-			reg-names = "ctrl", "config";
-			#address-cells = <3>;
-			#size-cells = <2>;
-			#interrupt-cells = <1>;
-			device_type = "pci";
-			dma-coherent;
-			msi-parent = <&gic_v2m0>;
-
-			bus-range = <0 0xff>;
-			ranges =
-				/* downstream I/O */
-				<0x81000000 0 0xfd000000 0  0xfd000000 0 0x10000
-				/* non-prefetchable memory */
-				0x82000000 0 0xfa000000 0  0xfa000000 0 0xf00000>;
-			interrupt-map-mask = <0 0 0 0>;
-			interrupt-map = <0 0 0 0 &cps_icu ICU_GRP_NSR 22 IRQ_TYPE_LEVEL_HIGH>;
-			interrupts = <ICU_GRP_NSR 22 IRQ_TYPE_LEVEL_HIGH>;
-			num-lanes = <1>;
-			clocks = <&cps_clk 1 13>;
-			status = "disabled";
-		};
-
-		cps_pcie1: pcie@f4620000 {
-			compatible = "marvell,armada8k-pcie", "snps,dw-pcie";
-			reg = <0 0xf4620000 0 0x10000>,
-			      <0 0xfbf00000 0 0x80000>;
-			reg-names = "ctrl", "config";
-			#address-cells = <3>;
-			#size-cells = <2>;
-			#interrupt-cells = <1>;
-			device_type = "pci";
-			dma-coherent;
-			msi-parent = <&gic_v2m0>;
-
-			bus-range = <0 0xff>;
-			ranges =
-				/* downstream I/O */
-				<0x81000000 0 0xfd010000 0  0xfd010000 0 0x10000
-				/* non-prefetchable memory */
-				0x82000000 0 0xfb000000 0  0xfb000000 0 0xf00000>;
-			interrupt-map-mask = <0 0 0 0>;
-			interrupt-map = <0 0 0 0 &cps_icu ICU_GRP_NSR 24 IRQ_TYPE_LEVEL_HIGH>;
-			interrupts = <ICU_GRP_NSR 24 IRQ_TYPE_LEVEL_HIGH>;
-
-			num-lanes = <1>;
-			clocks = <&cps_clk 1 11>;
-			status = "disabled";
-		};
-
-		cps_pcie2: pcie@f4640000 {
-			compatible = "marvell,armada8k-pcie", "snps,dw-pcie";
-			reg = <0 0xf4640000 0 0x10000>,
-			      <0 0xfcf00000 0 0x80000>;
-			reg-names = "ctrl", "config";
-			#address-cells = <3>;
-			#size-cells = <2>;
-			#interrupt-cells = <1>;
-			device_type = "pci";
-			dma-coherent;
-			msi-parent = <&gic_v2m0>;
-
-			bus-range = <0 0xff>;
-			ranges =
-				/* downstream I/O */
-				<0x81000000 0 0xfd020000 0  0xfd020000 0 0x10000
-				/* non-prefetchable memory */
-				0x82000000 0 0xfc000000 0  0xfc000000 0 0xf00000>;
-			interrupt-map-mask = <0 0 0 0>;
-			interrupt-map = <0 0 0 0 &cps_icu ICU_GRP_NSR 23 IRQ_TYPE_LEVEL_HIGH>;
-			interrupts = <ICU_GRP_NSR 23 IRQ_TYPE_LEVEL_HIGH>;
-
-			num-lanes = <1>;
-			clocks = <&cps_clk 1 12>;
-			status = "disabled";
-		};
-	};
-};

arch/arm64/boot/dts/marvell/armada-cp110.dtsi

@@ -0,0 +1,424 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR X11)
+/*
+ * Copyright (C) 2016 Marvell Technology Group Ltd.
+ */
+
+/*
+ * Device Tree file for Marvell Armada CP110.
+ */
+
+#include <dt-bindings/interrupt-controller/mvebu-icu.h>
+
+#include "armada-common.dtsi"
+
+#define CP110_PCIEx_IO_BASE(iface)	(CP110_PCIE_IO_BASE + (iface *  0x10000))
+#define CP110_PCIEx_MEM_BASE(iface)	(CP110_PCIE_MEM_BASE + (iface *  0x1000000))
+#define CP110_PCIEx_CONF_BASE(iface)	(CP110_PCIEx_MEM_BASE(iface) + 0xf00000)
+
+/ {
+	/*
+	 * The contents of the node are defined below, in order to
+	 * save one indentation level
+	 */
+	CP110_NAME: CP110_NAME { };
+};
+
+&CP110_NAME {
+	#address-cells = <2>;
+	#size-cells = <2>;
+	compatible = "simple-bus";
+	interrupt-parent = <&CP110_LABEL(icu)>;
+	ranges;
+
+	config-space@CP110_BASE {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "simple-bus";
+		ranges = <0x0 0x0 ADDRESSIFY(CP110_BASE) 0x2000000>;
+
+		CP110_LABEL(ethernet): ethernet@0 {
+			compatible = "marvell,armada-7k-pp22";
+			reg = <0x0 0x100000>, <0x129000 0xb000>;
+			clocks = <&CP110_LABEL(clk) 1 3>, <&CP110_LABEL(clk) 1 9>,
+				 <&CP110_LABEL(clk) 1 5>, <&CP110_LABEL(clk) 1 18>;
+			clock-names = "pp_clk", "gop_clk",
+				      "mg_clk", "axi_clk";
+			marvell,system-controller = <&CP110_LABEL(syscon0)>;
+			status = "disabled";
+			dma-coherent;
+
+			CP110_LABEL(eth0): eth0 {
+				interrupts = <ICU_GRP_NSR 39 IRQ_TYPE_LEVEL_HIGH>,
+					<ICU_GRP_NSR 43 IRQ_TYPE_LEVEL_HIGH>,
+					<ICU_GRP_NSR 47 IRQ_TYPE_LEVEL_HIGH>,
+					<ICU_GRP_NSR 51 IRQ_TYPE_LEVEL_HIGH>,
+					<ICU_GRP_NSR 55 IRQ_TYPE_LEVEL_HIGH>,
+					<ICU_GRP_NSR 129 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "tx-cpu0", "tx-cpu1", "tx-cpu2",
+					"tx-cpu3", "rx-shared", "link";
+				port-id = <0>;
+				gop-port-id = <0>;
+				status = "disabled";
+			};
+
+			CP110_LABEL(eth1): eth1 {
+				interrupts = <ICU_GRP_NSR 40 IRQ_TYPE_LEVEL_HIGH>,
+					<ICU_GRP_NSR 44 IRQ_TYPE_LEVEL_HIGH>,
+					<ICU_GRP_NSR 48 IRQ_TYPE_LEVEL_HIGH>,
+					<ICU_GRP_NSR 52 IRQ_TYPE_LEVEL_HIGH>,
+					<ICU_GRP_NSR 56 IRQ_TYPE_LEVEL_HIGH>,
+					<ICU_GRP_NSR 128 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "tx-cpu0", "tx-cpu1", "tx-cpu2",
+					"tx-cpu3", "rx-shared", "link";
+				port-id = <1>;
+				gop-port-id = <2>;
+				status = "disabled";
+			};
+
+			CP110_LABEL(eth2): eth2 {
+				interrupts = <ICU_GRP_NSR 41 IRQ_TYPE_LEVEL_HIGH>,
+					<ICU_GRP_NSR 45 IRQ_TYPE_LEVEL_HIGH>,
+					<ICU_GRP_NSR 49 IRQ_TYPE_LEVEL_HIGH>,
+					<ICU_GRP_NSR 53 IRQ_TYPE_LEVEL_HIGH>,
+					<ICU_GRP_NSR 57 IRQ_TYPE_LEVEL_HIGH>,
+					<ICU_GRP_NSR 127 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "tx-cpu0", "tx-cpu1", "tx-cpu2",
+					"tx-cpu3", "rx-shared", "link";
+				port-id = <2>;
+				gop-port-id = <3>;
+				status = "disabled";
+			};
+		};
+
+		CP110_LABEL(comphy): phy@120000 {
+			compatible = "marvell,comphy-cp110";
+			reg = <0x120000 0x6000>;
+			marvell,system-controller = <&CP110_LABEL(syscon0)>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			CP110_LABEL(comphy0): phy@0 {
+				reg = <0>;
+				#phy-cells = <1>;
+			};
+
+			CP110_LABEL(comphy1): phy@1 {
+				reg = <1>;
+				#phy-cells = <1>;
+			};
+
+			CP110_LABEL(comphy2): phy@2 {
+				reg = <2>;
+				#phy-cells = <1>;
+			};
+
+			CP110_LABEL(comphy3): phy@3 {
+				reg = <3>;
+				#phy-cells = <1>;
+			};
+
+			CP110_LABEL(comphy4): phy@4 {
+				reg = <4>;
+				#phy-cells = <1>;
+			};
+
+			CP110_LABEL(comphy5): phy@5 {
+				reg = <5>;
+				#phy-cells = <1>;
+			};
+		};
+
+		CP110_LABEL(mdio): mdio@12a200 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "marvell,orion-mdio";
+			reg = <0x12a200 0x10>;
+			clocks = <&CP110_LABEL(clk) 1 9>, <&CP110_LABEL(clk) 1 5>,
+				 <&CP110_LABEL(clk) 1 6>, <&CP110_LABEL(clk) 1 18>;
+			status = "disabled";
+		};
+
+		CP110_LABEL(xmdio): mdio@12a600 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "marvell,xmdio";
+			reg = <0x12a600 0x10>;
+			status = "disabled";
+		};
+
+		CP110_LABEL(icu): interrupt-controller@1e0000 {
+			compatible = "marvell,cp110-icu";
+			reg = <0x1e0000 0x10>;
+			#interrupt-cells = <3>;
+			interrupt-controller;
+			msi-parent = <&gicp>;
+		};
+
+		CP110_LABEL(rtc): rtc@284000 {
+			compatible = "marvell,armada-8k-rtc";
+			reg = <0x284000 0x20>, <0x284080 0x24>;
+			reg-names = "rtc", "rtc-soc";
+			interrupts = <ICU_GRP_NSR 77 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		CP110_LABEL(thermal): thermal@400078 {
+			compatible = "marvell,armada-cp110-thermal";
+			reg = <0x400078 0x4>,
+			<0x400070 0x8>;
+		};
+
+		CP110_LABEL(syscon0): system-controller@440000 {
+			compatible = "syscon", "simple-mfd";
+			reg = <0x440000 0x2000>;
+
+			CP110_LABEL(clk): clock {
+				compatible = "marvell,cp110-clock";
+				#clock-cells = <2>;
+			};
+
+			CP110_LABEL(gpio1): gpio@100 {
+				compatible = "marvell,armada-8k-gpio";
+				offset = <0x100>;
+				ngpios = <32>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				gpio-ranges = <&CP110_LABEL(pinctrl) 0 0 32>;
+				interrupt-controller;
+				interrupts = <ICU_GRP_NSR 86 IRQ_TYPE_LEVEL_HIGH>,
+					<ICU_GRP_NSR 85 IRQ_TYPE_LEVEL_HIGH>,
+					<ICU_GRP_NSR 84 IRQ_TYPE_LEVEL_HIGH>,
+					<ICU_GRP_NSR 83 IRQ_TYPE_LEVEL_HIGH>;
+				status = "disabled";
+			};
+
+			CP110_LABEL(gpio2): gpio@140 {
+				compatible = "marvell,armada-8k-gpio";
+				offset = <0x140>;
+				ngpios = <31>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				gpio-ranges = <&CP110_LABEL(pinctrl) 0 32 31>;
+				interrupt-controller;
+				interrupts = <ICU_GRP_NSR 82 IRQ_TYPE_LEVEL_HIGH>,
+					<ICU_GRP_NSR 81 IRQ_TYPE_LEVEL_HIGH>,
+					<ICU_GRP_NSR 80 IRQ_TYPE_LEVEL_HIGH>,
+					<ICU_GRP_NSR 79 IRQ_TYPE_LEVEL_HIGH>;
+				status = "disabled";
+			};
+		};
+
+		CP110_LABEL(usb3_0): usb3@500000 {
+			compatible = "marvell,armada-8k-xhci",
+			"generic-xhci";
+			reg = <0x500000 0x4000>;
+			dma-coherent;
+			interrupts = <ICU_GRP_NSR 106 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&CP110_LABEL(clk) 1 22>;
+			status = "disabled";
+		};
+
+		CP110_LABEL(usb3_1): usb3@510000 {
+			compatible = "marvell,armada-8k-xhci",
+			"generic-xhci";
+			reg = <0x510000 0x4000>;
+			dma-coherent;
+			interrupts = <ICU_GRP_NSR 105 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&CP110_LABEL(clk) 1 23>;
+			status = "disabled";
+		};
+
+		CP110_LABEL(sata0): sata@540000 {
+			compatible = "marvell,armada-8k-ahci",
+			"generic-ahci";
+			reg = <0x540000 0x30000>;
+			interrupts = <ICU_GRP_NSR 107 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&CP110_LABEL(clk) 1 15>;
+			status = "disabled";
+		};
+
+		CP110_LABEL(xor0): xor@6a0000 {
+			compatible = "marvell,armada-7k-xor", "marvell,xor-v2";
+			reg = <0x6a0000 0x1000>, <0x6b0000 0x1000>;
+			dma-coherent;
+			msi-parent = <&gic_v2m0>;
+			clocks = <&CP110_LABEL(clk) 1 8>;
+		};
+
+		CP110_LABEL(xor1): xor@6c0000 {
+			compatible = "marvell,armada-7k-xor", "marvell,xor-v2";
+			reg = <0x6c0000 0x1000>, <0x6d0000 0x1000>;
+			dma-coherent;
+			msi-parent = <&gic_v2m0>;
+			clocks = <&CP110_LABEL(clk) 1 7>;
+		};
+
+		CP110_LABEL(spi0): spi@700600 {
+			compatible = "marvell,armada-380-spi";
+			reg = <0x700600 0x50>;
+			#address-cells = <0x1>;
+			#size-cells = <0x0>;
+			clocks = <&CP110_LABEL(clk) 1 21>;
+			status = "disabled";
+		};
+
+		CP110_LABEL(spi1): spi@700680 {
+			compatible = "marvell,armada-380-spi";
+			reg = <0x700680 0x50>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			clocks = <&CP110_LABEL(clk) 1 21>;
+			status = "disabled";
+		};
+
+		CP110_LABEL(i2c0): i2c@701000 {
+			compatible = "marvell,mv78230-i2c";
+			reg = <0x701000 0x20>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			interrupts = <ICU_GRP_NSR 120 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&CP110_LABEL(clk) 1 21>;
+			status = "disabled";
+		};
+
+		CP110_LABEL(i2c1): i2c@701100 {
+			compatible = "marvell,mv78230-i2c";
+			reg = <0x701100 0x20>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			interrupts = <ICU_GRP_NSR 121 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&CP110_LABEL(clk) 1 21>;
+			status = "disabled";
+		};
+
+		CP110_LABEL(nand): nand@720000 {
+			/*
+			* Due to the limitation of the pins available
+			* this controller is only usable on the CPM
+			* for A7K and on the CPS for A8K.
+			*/
+			compatible = "marvell,armada-8k-nand",
+			"marvell,armada370-nand";
+			reg = <0x720000 0x54>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			interrupts = <ICU_GRP_NSR 115 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&CP110_LABEL(clk) 1 2>;
+			marvell,system-controller = <&CP110_LABEL(syscon0)>;
+			status = "disabled";
+		};
+
+		CP110_LABEL(trng): trng@760000 {
+			compatible = "marvell,armada-8k-rng",
+			"inside-secure,safexcel-eip76";
+			reg = <0x760000 0x7d>;
+			interrupts = <ICU_GRP_NSR 95 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&CP110_LABEL(clk) 1 25>;
+			status = "okay";
+		};
+
+		CP110_LABEL(sdhci0): sdhci@780000 {
+			compatible = "marvell,armada-cp110-sdhci";
+			reg = <0x780000 0x300>;
+			interrupts = <ICU_GRP_NSR 27 IRQ_TYPE_LEVEL_HIGH>;
+			clock-names = "core", "axi";
+			clocks = <&CP110_LABEL(clk) 1 4>, <&CP110_LABEL(clk) 1 18>;
+			dma-coherent;
+			status = "disabled";
+		};
+
+		CP110_LABEL(crypto): crypto@800000 {
+			compatible = "inside-secure,safexcel-eip197";
+			reg = <0x800000 0x200000>;
+			interrupts = <ICU_GRP_NSR 87 IRQ_TYPE_LEVEL_HIGH>,
+				<ICU_GRP_NSR 88 IRQ_TYPE_LEVEL_HIGH>,
+				<ICU_GRP_NSR 89 IRQ_TYPE_LEVEL_HIGH>,
+				<ICU_GRP_NSR 90 IRQ_TYPE_LEVEL_HIGH>,
+				<ICU_GRP_NSR 91 IRQ_TYPE_LEVEL_HIGH>,
+				<ICU_GRP_NSR 92 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "mem", "ring0", "ring1",
+				"ring2", "ring3", "eip";
+			clocks = <&CP110_LABEL(clk) 1 26>;
+			dma-coherent;
+		};
+	};
+
+	CP110_LABEL(pcie0): pcie@CP110_PCIE0_BASE {
+		compatible = "marvell,armada8k-pcie", "snps,dw-pcie";
+		reg = <0 ADDRESSIFY(CP110_PCIE0_BASE) 0 0x10000>,
+		      <0 CP110_PCIEx_CONF_BASE(0) 0 0x80000>;
+		reg-names = "ctrl", "config";
+		#address-cells = <3>;
+		#size-cells = <2>;
+		#interrupt-cells = <1>;
+		device_type = "pci";
+		dma-coherent;
+		msi-parent = <&gic_v2m0>;
+
+		bus-range = <0 0xff>;
+		ranges =
+		/* downstream I/O */
+		<0x81000000 0 CP110_PCIEx_IO_BASE(0) 0  CP110_PCIEx_IO_BASE(0) 0 0x10000
+		/* non-prefetchable memory */
+		0x82000000 0 CP110_PCIEx_MEM_BASE(0) 0  CP110_PCIEx_MEM_BASE(0) 0 0xf00000>;
+		interrupt-map-mask = <0 0 0 0>;
+		interrupt-map = <0 0 0 0 &CP110_LABEL(icu) ICU_GRP_NSR 22 IRQ_TYPE_LEVEL_HIGH>;
+		interrupts = <ICU_GRP_NSR 22 IRQ_TYPE_LEVEL_HIGH>;
+		num-lanes = <1>;
+		clocks = <&CP110_LABEL(clk) 1 13>;
+		status = "disabled";
+	};
+
+	CP110_LABEL(pcie1): pcie@CP110_PCIE1_BASE {
+		compatible = "marvell,armada8k-pcie", "snps,dw-pcie";
+		reg = <0 ADDRESSIFY(CP110_PCIE1_BASE) 0 0x10000>,
+		      <0 CP110_PCIEx_CONF_BASE(1) 0 0x80000>;
+		reg-names = "ctrl", "config";
+		#address-cells = <3>;
+		#size-cells = <2>;
+		#interrupt-cells = <1>;
+		device_type = "pci";
+		dma-coherent;
+		msi-parent = <&gic_v2m0>;
+
+		bus-range = <0 0xff>;
+		ranges =
+		/* downstream I/O */
+		<0x81000000 0 CP110_PCIEx_IO_BASE(1) 0  CP110_PCIEx_IO_BASE(1) 0 0x10000
+		/* non-prefetchable memory */
+		0x82000000 0 CP110_PCIEx_MEM_BASE(1) 0  CP110_PCIEx_MEM_BASE(1) 0 0xf00000>;
+		interrupt-map-mask = <0 0 0 0>;
+		interrupt-map = <0 0 0 0 &CP110_LABEL(icu) ICU_GRP_NSR 24 IRQ_TYPE_LEVEL_HIGH>;
+		interrupts = <ICU_GRP_NSR 24 IRQ_TYPE_LEVEL_HIGH>;
+
+		num-lanes = <1>;
+		clocks = <&CP110_LABEL(clk) 1 11>;
+		status = "disabled";
+	};
+
+	CP110_LABEL(pcie2): pcie@CP110_PCIE2_BASE {
+		compatible = "marvell,armada8k-pcie", "snps,dw-pcie";
+		reg = <0 ADDRESSIFY(CP110_PCIE2_BASE) 0 0x10000>,
+		      <0 CP110_PCIEx_CONF_BASE(2) 0 0x80000>;
+		reg-names = "ctrl", "config";
+		#address-cells = <3>;
+		#size-cells = <2>;
+		#interrupt-cells = <1>;
+		device_type = "pci";
+		dma-coherent;
+		msi-parent = <&gic_v2m0>;
+
+		bus-range = <0 0xff>;
+		ranges =
+		/* downstream I/O */
+		<0x81000000 0 CP110_PCIEx_IO_BASE(2) 0  CP110_PCIEx_IO_BASE(2) 0 0x10000
+		/* non-prefetchable memory */
+		0x82000000 0 CP110_PCIEx_MEM_BASE(2) 0  CP110_PCIEx_MEM_BASE(2) 0 0xf00000>;
+		interrupt-map-mask = <0 0 0 0>;
+		interrupt-map = <0 0 0 0 &CP110_LABEL(icu) ICU_GRP_NSR 23 IRQ_TYPE_LEVEL_HIGH>;
+		interrupts = <ICU_GRP_NSR 23 IRQ_TYPE_LEVEL_HIGH>;
+
+		num-lanes = <1>;
+		clocks = <&CP110_LABEL(clk) 1 12>;
+		status = "disabled";
+	};
+};

arch/arm64/boot/dts/mediatek/mt2712-evb.dts

@@ -24,6 +24,33 @@
 	chosen {
 		stdout-path = "serial0:921600n8";
 	};
+
+	cpus_fixed_vproc0: fixedregulator@0 {
+		compatible = "regulator-fixed";
+		regulator-name = "vproc_buck0";
+		regulator-min-microvolt = <1000000>;
+		regulator-max-microvolt = <1000000>;
+	};
+
+	cpus_fixed_vproc1: fixedregulator@1 {
+		compatible = "regulator-fixed";
+		regulator-name = "vproc_buck1";
+		regulator-min-microvolt = <1000000>;
+		regulator-max-microvolt = <1000000>;
+	};
+
+};
+
+&cpu0 {
+	proc-supply = <&cpus_fixed_vproc0>;
+};
+
+&cpu1 {
+	proc-supply = <&cpus_fixed_vproc0>;
+};
+
+&cpu2 {
+	proc-supply = <&cpus_fixed_vproc1>;
 };
 
 &uart0 {

arch/arm64/boot/dts/mediatek/mt2712e.dtsi

@@ -5,8 +5,10 @@
  * SPDX-License-Identifier: (GPL-2.0 OR MIT)
  */
 
+#include <dt-bindings/clock/mt2712-clk.h>
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/power/mt2712-power.h>
 
 / {
 	compatible = "mediatek,mt2712";
@@ -14,6 +16,48 @@
 	#address-cells = <2>;
 	#size-cells = <2>;
 
+	cluster0_opp: opp_table0 {
+		compatible = "operating-points-v2";
+		opp-shared;
+		opp00 {
+			opp-hz = /bits/ 64 <598000000>;
+			opp-microvolt = <1000000>;
+		};
+		opp01 {
+			opp-hz = /bits/ 64 <702000000>;
+			opp-microvolt = <1000000>;
+		};
+		opp02 {
+			opp-hz = /bits/ 64 <793000000>;
+			opp-microvolt = <1000000>;
+		};
+	};
+
+	cluster1_opp: opp_table1 {
+		compatible = "operating-points-v2";
+		opp-shared;
+		opp00 {
+			opp-hz = /bits/ 64 <598000000>;
+			opp-microvolt = <1000000>;
+		};
+		opp01 {
+			opp-hz = /bits/ 64 <702000000>;
+			opp-microvolt = <1000000>;
+		};
+		opp02 {
+			opp-hz = /bits/ 64 <793000000>;
+			opp-microvolt = <1000000>;
+		};
+		opp03 {
+			opp-hz = /bits/ 64 <897000000>;
+			opp-microvolt = <1000000>;
+		};
+		opp04 {
+			opp-hz = /bits/ 64 <1001000000>;
+			opp-microvolt = <1000000>;
+		};
+	};
+
 	cpus {
 		#address-cells = <1>;
 		#size-cells = <0>;
@@ -39,6 +83,11 @@
 			device_type = "cpu";
 			compatible = "arm,cortex-a35";
 			reg = <0x000>;
+			clocks = <&mcucfg CLK_MCU_MP0_SEL>,
+				<&topckgen CLK_TOP_F_MP0_PLL1>;
+			clock-names = "cpu", "intermediate";
+			proc-supply = <&cpus_fixed_vproc0>;
+			operating-points-v2 = <&cluster0_opp>;
 			cpu-idle-states = <&CPU_SLEEP_0 &CLUSTER_SLEEP_0>;
 		};
 
@@ -47,6 +96,11 @@
 			compatible = "arm,cortex-a35";
 			reg = <0x001>;
 			enable-method = "psci";
+			clocks = <&mcucfg CLK_MCU_MP0_SEL>,
+				<&topckgen CLK_TOP_F_MP0_PLL1>;
+			clock-names = "cpu", "intermediate";
+			proc-supply = <&cpus_fixed_vproc0>;
+			operating-points-v2 = <&cluster0_opp>;
 			cpu-idle-states = <&CPU_SLEEP_0 &CLUSTER_SLEEP_0>;
 		};
 
@@ -55,6 +109,11 @@
 			compatible = "arm,cortex-a72";
 			reg = <0x200>;
 			enable-method = "psci";
+			clocks = <&mcucfg CLK_MCU_MP2_SEL>,
+				<&topckgen CLK_TOP_F_BIG_PLL1>;
+			clock-names = "cpu", "intermediate";
+			proc-supply = <&cpus_fixed_vproc1>;
+			operating-points-v2 = <&cluster1_opp>;
 			cpu-idle-states = <&CPU_SLEEP_0 &CLUSTER_SLEEP_0>;
 		};
 
@@ -98,6 +157,48 @@
 		#clock-cells = <0>;
 	};
 
+	clk26m: oscillator@0 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <26000000>;
+		clock-output-names = "clk26m";
+	};
+
+	clk32k: oscillator@1 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+		clock-output-names = "clk32k";
+	};
+
+	clkfpc: oscillator@2 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <50000000>;
+		clock-output-names = "clkfpc";
+	};
+
+	clkaud_ext_i_0: oscillator@3 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <6500000>;
+		clock-output-names = "clkaud_ext_i_0";
+	};
+
+	clkaud_ext_i_1: oscillator@4 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <196608000>;
+		clock-output-names = "clkaud_ext_i_1";
+	};
+
+	clkaud_ext_i_2: oscillator@5 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <180633600>;
+		clock-output-names = "clkaud_ext_i_2";
+	};
+
 	timer {
 		compatible = "arm,armv8-timer";
 		interrupt-parent = <&gic>;
@@ -111,6 +212,39 @@
 			      (GIC_CPU_MASK_RAW(0x13) | IRQ_TYPE_LEVEL_LOW)>;
 	};
 
+	topckgen: syscon@10000000 {
+		compatible = "mediatek,mt2712-topckgen", "syscon";
+		reg = <0 0x10000000 0 0x1000>;
+		#clock-cells = <1>;
+	};
+
+	infracfg: syscon@10001000 {
+		compatible = "mediatek,mt2712-infracfg", "syscon";
+		reg = <0 0x10001000 0 0x1000>;
+		#clock-cells = <1>;
+	};
+
+	pericfg: syscon@10003000 {
+		compatible = "mediatek,mt2712-pericfg", "syscon";
+		reg = <0 0x10003000 0 0x1000>;
+		#clock-cells = <1>;
+	};
+
+	scpsys: scpsys@10006000 {
+		compatible = "mediatek,mt2712-scpsys", "syscon";
+		#power-domain-cells = <1>;
+		reg = <0 0x10006000 0 0x1000>;
+		clocks = <&topckgen CLK_TOP_MM_SEL>,
+			 <&topckgen CLK_TOP_MFG_SEL>,
+			 <&topckgen CLK_TOP_VENC_SEL>,
+			 <&topckgen CLK_TOP_JPGDEC_SEL>,
+			 <&topckgen CLK_TOP_A1SYS_HP_SEL>,
+			 <&topckgen CLK_TOP_VDEC_SEL>;
+		clock-names = "mm", "mfg", "venc",
+			"jpgdec", "audio", "vdec";
+		infracfg = <&infracfg>;
+	};
+
 	uart5: serial@1000f000 {
 		compatible = "mediatek,mt2712-uart",
 			     "mediatek,mt6577-uart";
@@ -121,6 +255,18 @@
 		status = "disabled";
 	};
 
+	apmixedsys: syscon@10209000 {
+		compatible = "mediatek,mt2712-apmixedsys", "syscon";
+		reg = <0 0x10209000 0 0x1000>;
+		#clock-cells = <1>;
+	};
+
+	mcucfg: syscon@10220000 {
+		compatible = "mediatek,mt2712-mcucfg", "syscon";
+		reg = <0 0x10220000 0 0x1000>;
+		#clock-cells = <1>;
+	};
+
 	sysirq: interrupt-controller@10220a80 {
 		compatible = "mediatek,mt2712-sysirq",
 			     "mediatek,mt6577-sysirq";
@@ -192,5 +338,47 @@
 		clock-names = "baud", "bus";
 		status = "disabled";
 	};
+
+	mfgcfg: syscon@13000000 {
+		compatible = "mediatek,mt2712-mfgcfg", "syscon";
+		reg = <0 0x13000000 0 0x1000>;
+		#clock-cells = <1>;
+	};
+
+	mmsys: syscon@14000000 {
+		compatible = "mediatek,mt2712-mmsys", "syscon";
+		reg = <0 0x14000000 0 0x1000>;
+		#clock-cells = <1>;
+	};
+
+	imgsys: syscon@15000000 {
+		compatible = "mediatek,mt2712-imgsys", "syscon";
+		reg = <0 0x15000000 0 0x1000>;
+		#clock-cells = <1>;
+	};
+
+	bdpsys: syscon@15010000 {
+		compatible = "mediatek,mt2712-bdpsys", "syscon";
+		reg = <0 0x15010000 0 0x1000>;
+		#clock-cells = <1>;
+	};
+
+	vdecsys: syscon@16000000 {
+		compatible = "mediatek,mt2712-vdecsys", "syscon";
+		reg = <0 0x16000000 0 0x1000>;
+		#clock-cells = <1>;
+	};
+
+	vencsys: syscon@18000000 {
+		compatible = "mediatek,mt2712-vencsys", "syscon";
+		reg = <0 0x18000000 0 0x1000>;
+		#clock-cells = <1>;
+	};
+
+	jpgdecsys: syscon@19000000 {
+		compatible = "mediatek,mt2712-jpgdecsys", "syscon";
+		reg = <0 0x19000000 0 0x1000>;
+		#clock-cells = <1>;
+	};
 };
 

arch/arm64/boot/dts/mediatek/mt8173-evb.dts

@@ -74,6 +74,24 @@
 	status = "okay";
 };
 
+&cpu0 {
+	proc-supply = <&mt6397_vpca15_reg>;
+};
+
+&cpu1 {
+	proc-supply = <&mt6397_vpca15_reg>;
+};
+
+&cpu2 {
+	proc-supply = <&da9211_vcpu_reg>;
+	sram-supply = <&mt6397_vsramca7_reg>;
+};
+
+&cpu3 {
+	proc-supply = <&da9211_vcpu_reg>;
+	sram-supply = <&mt6397_vsramca7_reg>;
+};
+
 &dpi0 {
 	status = "okay";
 };
@@ -505,7 +523,7 @@
 	vbus-supply = <&usb_p0_vbus>;
 	extcon = <&extcon_usb>;
 	dr_mode = "otg";
-	mediatek,enable-wakeup;
+	wakeup-source;
 	pinctrl-names = "default", "id_float", "id_ground";
 	pinctrl-0 = <&usb_id_pins_float>;
 	pinctrl-1 = <&usb_id_pins_float>;

arch/arm64/boot/dts/mediatek/mt8173.dtsi

@@ -51,6 +51,80 @@
 		mdp_wrot1 = &mdp_wrot1;
 	};
 
+	cluster0_opp: opp_table0 {
+		compatible = "operating-points-v2";
+		opp-shared;
+		opp-507000000 {
+			opp-hz = /bits/ 64 <507000000>;
+			opp-microvolt = <859000>;
+		};
+		opp-702000000 {
+			opp-hz = /bits/ 64 <702000000>;
+			opp-microvolt = <908000>;
+		};
+		opp-1001000000 {
+			opp-hz = /bits/ 64 <1001000000>;
+			opp-microvolt = <983000>;
+		};
+		opp-1105000000 {
+			opp-hz = /bits/ 64 <1105000000>;
+			opp-microvolt = <1009000>;
+		};
+		opp-1209000000 {
+			opp-hz = /bits/ 64 <1209000000>;
+			opp-microvolt = <1034000>;
+		};
+		opp-1300000000 {
+			opp-hz = /bits/ 64 <1300000000>;
+			opp-microvolt = <1057000>;
+		};
+		opp-1508000000 {
+			opp-hz = /bits/ 64 <1508000000>;
+			opp-microvolt = <1109000>;
+		};
+		opp-1703000000 {
+			opp-hz = /bits/ 64 <1703000000>;
+			opp-microvolt = <1125000>;
+		};
+	};
+
+	cluster1_opp: opp_table1 {
+		compatible = "operating-points-v2";
+		opp-shared;
+		opp-507000000 {
+			opp-hz = /bits/ 64 <507000000>;
+			opp-microvolt = <828000>;
+		};
+		opp-702000000 {
+			opp-hz = /bits/ 64 <702000000>;
+			opp-microvolt = <867000>;
+		};
+		opp-1001000000 {
+			opp-hz = /bits/ 64 <1001000000>;
+			opp-microvolt = <927000>;
+		};
+		opp-1209000000 {
+			opp-hz = /bits/ 64 <1209000000>;
+			opp-microvolt = <968000>;
+		};
+		opp-1404000000 {
+			opp-hz = /bits/ 64 <1404000000>;
+			opp-microvolt = <1007000>;
+		};
+		opp-1612000000 {
+			opp-hz = /bits/ 64 <1612000000>;
+			opp-microvolt = <1049000>;
+		};
+		opp-1807000000 {
+			opp-hz = /bits/ 64 <1807000000>;
+			opp-microvolt = <1089000>;
+		};
+		opp-2106000000 {
+			opp-hz = /bits/ 64 <2106000000>;
+			opp-microvolt = <1125000>;
+		};
+	};
+
 	cpus {
 		#address-cells = <1>;
 		#size-cells = <0>;
@@ -81,6 +155,11 @@
 			reg = <0x000>;
 			enable-method = "psci";
 			cpu-idle-states = <&CPU_SLEEP_0>;
+			#cooling-cells = <2>;
+			clocks = <&infracfg CLK_INFRA_CA53SEL>,
+				 <&apmixedsys CLK_APMIXED_MAINPLL>;
+			clock-names = "cpu", "intermediate";
+			operating-points-v2 = <&cluster0_opp>;
 		};
 
 		cpu1: cpu@1 {
@@ -89,6 +168,10 @@
 			reg = <0x001>;
 			enable-method = "psci";
 			cpu-idle-states = <&CPU_SLEEP_0>;
+			clocks = <&infracfg CLK_INFRA_CA53SEL>,
+				 <&apmixedsys CLK_APMIXED_MAINPLL>;
+			clock-names = "cpu", "intermediate";
+			operating-points-v2 = <&cluster0_opp>;
 		};
 
 		cpu2: cpu@100 {
@@ -97,6 +180,11 @@
 			reg = <0x100>;
 			enable-method = "psci";
 			cpu-idle-states = <&CPU_SLEEP_0>;
+			#cooling-cells = <2>;
+			clocks = <&infracfg CLK_INFRA_CA57SEL>,
+				 <&apmixedsys CLK_APMIXED_MAINPLL>;
+			clock-names = "cpu", "intermediate";
+			operating-points-v2 = <&cluster1_opp>;
 		};
 
 		cpu3: cpu@101 {
@@ -105,6 +193,10 @@
 			reg = <0x101>;
 			enable-method = "psci";
 			cpu-idle-states = <&CPU_SLEEP_0>;
+			clocks = <&infracfg CLK_INFRA_CA57SEL>,
+				 <&apmixedsys CLK_APMIXED_MAINPLL>;
+			clock-names = "cpu", "intermediate";
+			operating-points-v2 = <&cluster1_opp>;
 		};
 
 		idle-states {
@@ -731,15 +823,9 @@
 			       <&u3port0 PHY_TYPE_USB3>,
 			       <&u2port1 PHY_TYPE_USB2>;
 			power-domains = <&scpsys MT8173_POWER_DOMAIN_USB>;
-			clocks = <&topckgen CLK_TOP_USB30_SEL>,
-				 <&clk26m>,
-				 <&pericfg CLK_PERI_USB0>,
-				 <&pericfg CLK_PERI_USB1>;
-			clock-names = "sys_ck",
-				      "ref_ck",
-				      "wakeup_deb_p0",
-				      "wakeup_deb_p1";
-			mediatek,syscon-wakeup = <&pericfg>;
+			clocks = <&topckgen CLK_TOP_USB30_SEL>, <&clk26m>;
+			clock-names = "sys_ck", "ref_ck";
+			mediatek,syscon-wakeup = <&pericfg 0x400 1>;
 			#address-cells = <2>;
 			#size-cells = <2>;
 			ranges;

arch/arm64/boot/dts/nvidia/tegra186-p2771-0000.dts

@@ -74,6 +74,43 @@
 		};
 	};
 
+	host1x@13e00000 {
+		status = "okay";
+
+		dpaux@15040000 {
+			status = "okay";
+		};
+
+		display-hub@15200000 {
+			status = "okay";
+		};
+
+		dsi@15300000 {
+			status = "disabled";
+		};
+
+		sor@15540000 {
+			status = "disabled";
+
+			nvidia,dpaux = <&dpaux1>;
+		};
+
+		sor@15580000 {
+			status = "okay";
+
+			avdd-io-supply = <&vdd_hdmi_1v05>;
+			vdd-pll-supply = <&vdd_1v8_ap>;
+			hdmi-supply = <&vdd_hdmi>;
+
+			nvidia,ddc-i2c-bus = <&ddc>;
+			nvidia,hpd-gpio = <&gpio TEGRA_MAIN_GPIO(P, 1) GPIO_ACTIVE_LOW>;
+		};
+
+		dpaux@155c0000 {
+			status = "okay";
+		};
+	};
+
 	gpio-keys {
 		compatible = "gpio-keys";
 
@@ -120,5 +157,19 @@
 
 			vin-supply = <&vdd_3v3_sys>;
 		};
+
+		vdd_hdmi: regulator@101 {
+			compatible = "regulator-fixed";
+			reg = <101>;
+
+			regulator-name = "VDD_HDMI_5V0";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+
+			gpio = <&exp1 14 GPIO_ACTIVE_HIGH>;
+			enable-active-high;
+
+			vin-supply = <&vdd_5v0_sys>;
+		};
 	};
 };

arch/arm64/boot/dts/nvidia/tegra186-p3310.dtsi

@@ -51,6 +51,10 @@
 		};
 	};
 
+	memory-controller@2c00000 {
+		status = "okay";
+	};
+
 	serial@3100000 {
 		status = "okay";
 	};
@@ -73,7 +77,7 @@
 		status = "okay";
 	};
 
-	i2c@3190000 {
+	ddc: i2c@3190000 {
 		status = "okay";
 	};
 
@@ -88,7 +92,7 @@
 	/* SDMMC1 (SD/MMC) */
 	sdhci@3400000 {
 		cd-gpios = <&gpio TEGRA_MAIN_GPIO(P, 5) GPIO_ACTIVE_LOW>;
-		wp-gpios = <&gpio TEGRA_MAIN_GPIO(P, 4) GPIO_ACTIVE_LOW>;
+		wp-gpios = <&gpio TEGRA_MAIN_GPIO(P, 4) GPIO_ACTIVE_HIGH>;
 
 		vqmmc-supply = <&vddio_sdmmc1>;
 	};
@@ -317,7 +321,7 @@
 						regulator-max-microvolt = <2800000>;
 					};
 
-					avdd_1v05: ldo7 {
+					vdd_hdmi_1v05: ldo7 {
 						regulator-name = "VDD_HDMI_1V05";
 						regulator-min-microvolt = <1050000>;
 						regulator-max-microvolt = <1050000>;

arch/arm64/boot/dts/nvidia/tegra186.dtsi

@@ -3,6 +3,7 @@
 #include <dt-bindings/gpio/tegra186-gpio.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/mailbox/tegra186-hsp.h>
+#include <dt-bindings/memory/tegra186-mc.h>
 #include <dt-bindings/power/tegra186-powergate.h>
 #include <dt-bindings/reset/tegra186-reset.h>
 #include <dt-bindings/thermal/tegra186-bpmp-thermal.h>
@@ -13,6 +14,12 @@
 	#address-cells = <2>;
 	#size-cells = <2>;
 
+	misc@100000 {
+		compatible = "nvidia,tegra186-misc";
+		reg = <0x0 0x00100000 0x0 0xf000>,
+		      <0x0 0x0010f000 0x0 0x1000>;
+	};
+
 	gpio: gpio@2200000 {
 		compatible = "nvidia,tegra186-gpio";
 		reg-names = "security", "gpio";
@@ -61,6 +68,12 @@
 		snps,rxpbl = <8>;
 	};
 
+	memory-controller@2c00000 {
+		compatible = "nvidia,tegra186-mc";
+		reg = <0x0 0x02c00000 0x0 0xb0000>;
+		status = "disabled";
+	};
+
 	uarta: serial@3100000 {
 		compatible = "nvidia,tegra186-uart", "nvidia,tegra20-uart";
 		reg = <0x0 0x03100000 0x0 0x40>;
@@ -259,6 +272,13 @@
 		status = "disabled";
 	};
 
+	fuse@3820000 {
+		compatible = "nvidia,tegra186-efuse";
+		reg = <0x0 0x03820000 0x0 0x10000>;
+		clocks = <&bpmp TEGRA186_CLK_FUSE>;
+		clock-names = "fuse";
+	};
+
 	gic: interrupt-controller@3881000 {
 		compatible = "arm,gic-400";
 		#interrupt-cells = <3>;
@@ -437,6 +457,79 @@
 		};
 	};
 
+	smmu: iommu@12000000 {
+		compatible = "arm,mmu-500";
+		reg = <0 0x12000000 0 0x800000>;
+		interrupts = <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>;
+		stream-match-mask = <0x7f80>;
+		#global-interrupts = <1>;
+		#iommu-cells = <1>;
+	};
+
 	host1x@13e00000 {
 		compatible = "nvidia,tegra186-host1x", "simple-bus";
 		reg = <0x0 0x13e00000 0x0 0x10000>,
@@ -453,6 +546,129 @@
 		#size-cells = <1>;
 
 		ranges = <0x15000000 0x0 0x15000000 0x01000000>;
+		iommus = <&smmu TEGRA186_SID_HOST1X>;
+
+		dpaux1: dpaux@15040000 {
+			compatible = "nvidia,tegra186-dpaux";
+			reg = <0x15040000 0x10000>;
+			interrupts = <GIC_SPI 160 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&bpmp TEGRA186_CLK_DPAUX1>,
+				 <&bpmp TEGRA186_CLK_PLLDP>;
+			clock-names = "dpaux", "parent";
+			resets = <&bpmp TEGRA186_RESET_DPAUX1>;
+			reset-names = "dpaux";
+			status = "disabled";
+
+			power-domains = <&bpmp TEGRA186_POWER_DOMAIN_DISP>;
+
+			state_dpaux1_aux: pinmux-aux {
+				groups = "dpaux-io";
+				function = "aux";
+			};
+
+			state_dpaux1_i2c: pinmux-i2c {
+				groups = "dpaux-io";
+				function = "i2c";
+			};
+
+			state_dpaux1_off: pinmux-off {
+				groups = "dpaux-io";
+				function = "off";
+			};
+
+			i2c-bus {
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+
+		display-hub@15200000 {
+			compatible = "nvidia,tegra186-display", "simple-bus";
+			resets = <&bpmp TEGRA186_RESET_NVDISPLAY0_MISC>,
+				 <&bpmp TEGRA186_RESET_NVDISPLAY0_WGRP0>,
+				 <&bpmp TEGRA186_RESET_NVDISPLAY0_WGRP1>,
+				 <&bpmp TEGRA186_RESET_NVDISPLAY0_WGRP2>,
+				 <&bpmp TEGRA186_RESET_NVDISPLAY0_WGRP3>,
+				 <&bpmp TEGRA186_RESET_NVDISPLAY0_WGRP4>,
+				 <&bpmp TEGRA186_RESET_NVDISPLAY0_WGRP5>;
+			reset-names = "misc", "wgrp0", "wgrp1", "wgrp2",
+				      "wgrp3", "wgrp4", "wgrp5";
+			clocks = <&bpmp TEGRA186_CLK_NVDISPLAY_DISP>,
+				 <&bpmp TEGRA186_CLK_NVDISPLAY_DSC>,
+				 <&bpmp TEGRA186_CLK_NVDISPLAYHUB>;
+			clock-names = "disp", "dsc", "hub";
+			status = "disabled";
+
+			power-domains = <&bpmp TEGRA186_POWER_DOMAIN_DISP>;
+
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			ranges = <0x15200000 0x15200000 0x40000>;
+
+			display@15200000 {
+				compatible = "nvidia,tegra186-dc";
+				reg = <0x15200000 0x10000>;
+				interrupts = <GIC_SPI 153 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&bpmp TEGRA186_CLK_NVDISPLAY_P0>;
+				clock-names = "dc";
+				resets = <&bpmp TEGRA186_RESET_NVDISPLAY0_HEAD0>;
+				reset-names = "dc";
+
+				power-domains = <&bpmp TEGRA186_POWER_DOMAIN_DISP>;
+				iommus = <&smmu TEGRA186_SID_NVDISPLAY>;
+
+				nvidia,outputs = <&dsia &dsib &sor0 &sor1>;
+				nvidia,head = <0>;
+			};
+
+			display@15210000 {
+				compatible = "nvidia,tegra186-dc";
+				reg = <0x15210000 0x10000>;
+				interrupts = <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&bpmp TEGRA186_CLK_NVDISPLAY_P1>;
+				clock-names = "dc";
+				resets = <&bpmp TEGRA186_RESET_NVDISPLAY0_HEAD1>;
+				reset-names = "dc";
+
+				power-domains = <&bpmp TEGRA186_POWER_DOMAIN_DISPB>;
+				iommus = <&smmu TEGRA186_SID_NVDISPLAY>;
+
+				nvidia,outputs = <&dsia &dsib &sor0 &sor1>;
+				nvidia,head = <1>;
+			};
+
+			display@15220000 {
+				compatible = "nvidia,tegra186-dc";
+				reg = <0x15220000 0x10000>;
+				interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&bpmp TEGRA186_CLK_NVDISPLAY_P2>;
+				clock-names = "dc";
+				resets = <&bpmp TEGRA186_RESET_NVDISPLAY0_HEAD2>;
+				reset-names = "dc";
+
+				power-domains = <&bpmp TEGRA186_POWER_DOMAIN_DISPC>;
+				iommus = <&smmu TEGRA186_SID_NVDISPLAY>;
+
+				nvidia,outputs = <&sor0 &sor1>;
+				nvidia,head = <2>;
+			};
+		};
+
+		dsia: dsi@15300000 {
+			compatible = "nvidia,tegra186-dsi";
+			reg = <0x15300000 0x10000>;
+			interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&bpmp TEGRA186_CLK_DSI>,
+				 <&bpmp TEGRA186_CLK_DSIA_LP>,
+				 <&bpmp TEGRA186_CLK_PLLD>;
+			clock-names = "dsi", "lp", "parent";
+			resets = <&bpmp TEGRA186_RESET_DSI>;
+			reset-names = "dsi";
+			status = "disabled";
+
+			power-domains = <&bpmp TEGRA186_POWER_DOMAIN_DISP>;
+		};
 
 		vic@15340000 {
 			compatible = "nvidia,tegra186-vic";
@@ -465,6 +681,141 @@
 
 			power-domains = <&bpmp TEGRA186_POWER_DOMAIN_VIC>;
 		};
+
+		dsib: dsi@15400000 {
+			compatible = "nvidia,tegra186-dsi";
+			reg = <0x15400000 0x10000>;
+			interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&bpmp TEGRA186_CLK_DSIB>,
+				 <&bpmp TEGRA186_CLK_DSIB_LP>,
+				 <&bpmp TEGRA186_CLK_PLLD>;
+			clock-names = "dsi", "lp", "parent";
+			resets = <&bpmp TEGRA186_RESET_DSIB>;
+			reset-names = "dsi";
+			status = "disabled";
+
+			power-domains = <&bpmp TEGRA186_POWER_DOMAIN_DISP>;
+		};
+
+		sor0: sor@15540000 {
+			compatible = "nvidia,tegra186-sor";
+			reg = <0x15540000 0x10000>;
+			interrupts = <GIC_SPI 157 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&bpmp TEGRA186_CLK_SOR0>,
+				 <&bpmp TEGRA186_CLK_SOR0_OUT>,
+				 <&bpmp TEGRA186_CLK_PLLD2>,
+				 <&bpmp TEGRA186_CLK_PLLDP>,
+				 <&bpmp TEGRA186_CLK_SOR_SAFE>,
+				 <&bpmp TEGRA186_CLK_SOR0_PAD_CLKOUT>;
+			clock-names = "sor", "out", "parent", "dp", "safe",
+				      "pad";
+			resets = <&bpmp TEGRA186_RESET_SOR0>;
+			reset-names = "sor";
+			pinctrl-0 = <&state_dpaux_aux>;
+			pinctrl-1 = <&state_dpaux_i2c>;
+			pinctrl-2 = <&state_dpaux_off>;
+			pinctrl-names = "aux", "i2c", "off";
+			status = "disabled";
+
+			power-domains = <&bpmp TEGRA186_POWER_DOMAIN_DISP>;
+			nvidia,interface = <0>;
+		};
+
+		sor1: sor@15580000 {
+			compatible = "nvidia,tegra186-sor1";
+			reg = <0x15580000 0x10000>;
+			interrupts = <GIC_SPI 158 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&bpmp TEGRA186_CLK_SOR1>,
+				 <&bpmp TEGRA186_CLK_SOR1_OUT>,
+				 <&bpmp TEGRA186_CLK_PLLD3>,
+				 <&bpmp TEGRA186_CLK_PLLDP>,
+				 <&bpmp TEGRA186_CLK_SOR_SAFE>,
+				 <&bpmp TEGRA186_CLK_SOR1_PAD_CLKOUT>;
+			clock-names = "sor", "out", "parent", "dp", "safe",
+				      "pad";
+			resets = <&bpmp TEGRA186_RESET_SOR1>;
+			reset-names = "sor";
+			pinctrl-0 = <&state_dpaux1_aux>;
+			pinctrl-1 = <&state_dpaux1_i2c>;
+			pinctrl-2 = <&state_dpaux1_off>;
+			pinctrl-names = "aux", "i2c", "off";
+			status = "disabled";
+
+			power-domains = <&bpmp TEGRA186_POWER_DOMAIN_DISP>;
+			nvidia,interface = <1>;
+		};
+
+		dpaux: dpaux@155c0000 {
+			compatible = "nvidia,tegra186-dpaux";
+			reg = <0x155c0000 0x10000>;
+			interrupts = <GIC_SPI 159 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&bpmp TEGRA186_CLK_DPAUX>,
+				 <&bpmp TEGRA186_CLK_PLLDP>;
+			clock-names = "dpaux", "parent";
+			resets = <&bpmp TEGRA186_RESET_DPAUX>;
+			reset-names = "dpaux";
+			status = "disabled";
+
+			power-domains = <&bpmp TEGRA186_POWER_DOMAIN_DISP>;
+
+			state_dpaux_aux: pinmux-aux {
+				groups = "dpaux-io";
+				function = "aux";
+			};
+
+			state_dpaux_i2c: pinmux-i2c {
+				groups = "dpaux-io";
+				function = "i2c";
+			};
+
+			state_dpaux_off: pinmux-off {
+				groups = "dpaux-io";
+				function = "off";
+			};
+
+			i2c-bus {
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+
+		padctl@15880000 {
+			compatible = "nvidia,tegra186-dsi-padctl";
+			reg = <0x15880000 0x10000>;
+			resets = <&bpmp TEGRA186_RESET_DSI>;
+			reset-names = "dsi";
+			status = "disabled";
+		};
+
+		dsic: dsi@15900000 {
+			compatible = "nvidia,tegra186-dsi";
+			reg = <0x15900000 0x10000>;
+			interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&bpmp TEGRA186_CLK_DSIC>,
+				 <&bpmp TEGRA186_CLK_DSIC_LP>,
+				 <&bpmp TEGRA186_CLK_PLLD>;
+			clock-names = "dsi", "lp", "parent";
+			resets = <&bpmp TEGRA186_RESET_DSIC>;
+			reset-names = "dsi";
+			status = "disabled";
+
+			power-domains = <&bpmp TEGRA186_POWER_DOMAIN_DISP>;
+		};
+
+		dsid: dsi@15940000 {
+			compatible = "nvidia,tegra186-dsi";
+			reg = <0x15940000 0x10000>;
+			interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&bpmp TEGRA186_CLK_DSID>,
+				 <&bpmp TEGRA186_CLK_DSID_LP>,
+				 <&bpmp TEGRA186_CLK_PLLD>;
+			clock-names = "dsi", "lp", "parent";
+			resets = <&bpmp TEGRA186_RESET_DSID>;
+			reset-names = "dsi";
+			status = "disabled";
+
+			power-domains = <&bpmp TEGRA186_POWER_DOMAIN_DISP>;
+		};
 	};
 
 	gpu@17000000 {

arch/arm64/boot/dts/nvidia/tegra210-p2180.dtsi

@@ -297,6 +297,29 @@
 		};
 	};
 
+	cpus {
+		cpu@0 {
+			enable-method = "psci";
+		};
+
+		cpu@1 {
+			enable-method = "psci";
+		};
+
+		cpu@2 {
+			enable-method = "psci";
+		};
+
+		cpu@3 {
+			enable-method = "psci";
+		};
+	};
+
+	psci {
+		compatible = "arm,psci-0.2";
+		method = "smc";
+	};
+
 	regulators {
 		vdd_gpu: regulator@100 {
 			compatible = "pwm-regulator";

arch/arm64/boot/dts/nvidia/tegra210-p2530.dtsi

@@ -52,4 +52,27 @@
 			clock-frequency = <32768>;
 		};
 	};
+
+	cpus {
+		cpu@0 {
+			enable-method = "psci";
+		};
+
+		cpu@1 {
+			enable-method = "psci";
+		};
+
+		cpu@2 {
+			enable-method = "psci";
+		};
+
+		cpu@3 {
+			enable-method = "psci";
+		};
+	};
+
+	psci {
+		compatible = "arm,psci-0.2";
+		method = "smc";
+	};
 };

arch/arm64/boot/dts/nvidia/tegra210.dtsi

@@ -266,11 +266,11 @@
 			reg = <0x0 0x54580000 0x0 0x00040000>;
 			interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&tegra_car TEGRA210_CLK_SOR1>,
-				 <&tegra_car TEGRA210_CLK_SOR1_SRC>,
+				 <&tegra_car TEGRA210_CLK_SOR1_OUT>,
 				 <&tegra_car TEGRA210_CLK_PLL_D2_OUT0>,
 				 <&tegra_car TEGRA210_CLK_PLL_DP>,
 				 <&tegra_car TEGRA210_CLK_SOR_SAFE>;
-			clock-names = "sor", "source", "parent", "dp", "safe";
+			clock-names = "sor", "out", "parent", "dp", "safe";
 			resets = <&tegra_car 183>;
 			reset-names = "sor";
 			pinctrl-0 = <&state_dpaux1_aux>;

arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi

@@ -324,6 +324,7 @@
 				label = "apq8016-sbc:green:user4";
 				gpios = <&pm8916_gpios 2 GPIO_ACTIVE_HIGH>;
 				linux,default-trigger = "none";
+				panic-indicator;
 				default-state = "off";
 			};
 

arch/arm64/boot/dts/qcom/msm8916-pins.dtsi

@@ -278,7 +278,7 @@
 		pinconf {
 			pins = "gpio6", "gpio7";
 			drive-strength = <16>;
-			bias-disable = <0>;
+			bias-disable;
 		};
 	};
 
@@ -290,7 +290,7 @@
 		pinconf {
 			pins = "gpio6", "gpio7";
 			drive-strength = <2>;
-			bias-disable = <0>;
+			bias-disable;
 		};
 	};
 
@@ -302,7 +302,7 @@
 		pinconf {
 			pins = "gpio14", "gpio15";
 			drive-strength = <16>;
-			bias-disable = <0>;
+			bias-disable;
 		};
 	};
 
@@ -314,7 +314,7 @@
 		pinconf {
 			pins = "gpio14", "gpio15";
 			drive-strength = <2>;
-			bias-disable = <0>;
+			bias-disable;
 		};
 	};
 
@@ -326,7 +326,7 @@
 		pinconf {
 			pins = "gpio22", "gpio23";
 			drive-strength = <16>;
-			bias-disable = <0>;
+			bias-disable;
 		};
 	};
 
@@ -338,32 +338,7 @@
 		pinconf {
 			pins = "gpio22", "gpio23";
 			drive-strength = <2>;
-			bias-disable = <0>;
-		};
-	};
-
-	sdhc2_cd_pin {
-		sdc2_cd_on: cd_on {
-			pinmux {
-				function = "gpio";
-				pins = "gpio38";
-			};
-			pinconf {
-				pins = "gpio38";
-				drive-strength = <2>;
-				bias-pull-up;
-			};
-		};
-		sdc2_cd_off: cd_off {
-			pinmux {
-				function = "gpio";
-				pins = "gpio38";
-			};
-			pinconf {
-				pins = "gpio38";
-				drive-strength = <2>;
-				bias-disable;
-			};
+			bias-disable;
 		};
 	};
 
@@ -505,26 +480,25 @@
 		};
 	};
 
-	ext-codec-lines {
-		ext_codec_lines_act: lines_on {
+	pmx_sdc2_cd_pin {
+		sdc2_cd_on: cd_on {
 			pinmux {
 				function = "gpio";
-				pins = "gpio67";
+				pins = "gpio38";
 			};
 			pinconf {
-				pins = "gpio67";
-				drive-strength = <8>;
-				bias-disable;
-				output-high;
+				pins = "gpio38";
+				drive-strength = <2>;
+				bias-pull-up;
 			};
 		};
-		ext_codec_lines_sus: lines_off {
+		sdc2_cd_off: cd_off {
 			pinmux {
 				function = "gpio";
-				pins = "gpio67";
+				pins = "gpio38";
 			};
 			pinconf {
-				pins = "gpio67";
+				pins = "gpio38";
 				drive-strength = <2>;
 				bias-disable;
 			};
@@ -687,6 +661,14 @@
 			};
 		};
 		cdc_dmic_lines_sus: dmic_lines_off {
+			pinmux_dmic0_clk {
+				function = "dmic0_clk";
+				pins = "gpio0";
+			};
+			pinmux_dmic0_data {
+				function = "dmic0_data";
+				pins = "gpio1";
+			};
 			pinconf {
 				pins = "gpio0", "gpio1";
 				drive-strength = <2>;
@@ -695,32 +677,6 @@
 		};
 	};
 
-	cross-conn-det {
-		cross_conn_det_act: lines_on {
-			pinmux {
-				function = "gpio";
-				pins = "gpio120";
-			};
-			pinconf {
-				pins = "gpio120";
-				drive-strength = <8>;
-				output-low;
-				bias-pull-down;
-			};
-		};
-		cross_conn_det_sus: lines_off {
-			pinmux {
-				function = "gpio";
-				pins = "gpio120";
-			};
-			pinconf {
-				pins = "gpio120";
-				drive-strength = <2>;
-				bias-disable;
-			};
-		};
-	};
-
 	wcnss_pin_a: wcnss-active {
 		pinmux {
 			pins = "gpio40", "gpio41", "gpio42", "gpio43", "gpio44";

arch/arm64/boot/dts/qcom/msm8916.dtsi

@@ -355,7 +355,7 @@
 
 		blsp_spi1: spi@78b5000 {
 			compatible = "qcom,spi-qup-v2.2.1";
-			reg = <0x078b5000 0x600>;
+			reg = <0x078b5000 0x500>;
 			interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&gcc GCC_BLSP1_QUP1_SPI_APPS_CLK>,
 				 <&gcc GCC_BLSP1_AHB_CLK>;
@@ -372,7 +372,7 @@
 
 		blsp_spi2: spi@78b6000 {
 			compatible = "qcom,spi-qup-v2.2.1";
-			reg = <0x078b6000 0x600>;
+			reg = <0x078b6000 0x500>;
 			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&gcc GCC_BLSP1_QUP2_SPI_APPS_CLK>,
 				 <&gcc GCC_BLSP1_AHB_CLK>;
@@ -389,7 +389,7 @@
 
 		blsp_spi3: spi@78b7000 {
 			compatible = "qcom,spi-qup-v2.2.1";
-			reg = <0x078b7000 0x600>;
+			reg = <0x078b7000 0x500>;
 			interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&gcc GCC_BLSP1_QUP3_SPI_APPS_CLK>,
 				 <&gcc GCC_BLSP1_AHB_CLK>;
@@ -406,7 +406,7 @@
 
 		blsp_spi4: spi@78b8000 {
 			compatible = "qcom,spi-qup-v2.2.1";
-			reg = <0x078b8000 0x600>;
+			reg = <0x078b8000 0x500>;
 			interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&gcc GCC_BLSP1_QUP4_SPI_APPS_CLK>,
 				 <&gcc GCC_BLSP1_AHB_CLK>;
@@ -423,7 +423,7 @@
 
 		blsp_spi5: spi@78b9000 {
 			compatible = "qcom,spi-qup-v2.2.1";
-			reg = <0x078b9000 0x600>;
+			reg = <0x078b9000 0x500>;
 			interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&gcc GCC_BLSP1_QUP5_SPI_APPS_CLK>,
 				 <&gcc GCC_BLSP1_AHB_CLK>;
@@ -440,7 +440,7 @@
 
 		blsp_spi6: spi@78ba000 {
 			compatible = "qcom,spi-qup-v2.2.1";
-			reg = <0x078ba000 0x600>;
+			reg = <0x078ba000 0x500>;
 			interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&gcc GCC_BLSP1_QUP6_SPI_APPS_CLK>,
 				 <&gcc GCC_BLSP1_AHB_CLK>;
@@ -457,10 +457,10 @@
 
 		blsp_i2c2: i2c@78b6000 {
 			compatible = "qcom,i2c-qup-v2.2.1";
-			reg = <0x78b6000 0x1000>;
+			reg = <0x078b6000 0x500>;
 			interrupts = <GIC_SPI 96 0>;
 			clocks = <&gcc GCC_BLSP1_AHB_CLK>,
-				<&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>;
+				 <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>;
 			clock-names = "iface", "core";
 			pinctrl-names = "default", "sleep";
 			pinctrl-0 = <&i2c2_default>;
@@ -472,10 +472,10 @@
 
 		blsp_i2c4: i2c@78b8000 {
 			compatible = "qcom,i2c-qup-v2.2.1";
-			reg = <0x78b8000 0x1000>;
+			reg = <0x078b8000 0x500>;
 			interrupts = <GIC_SPI 98 0>;
 			clocks = <&gcc GCC_BLSP1_AHB_CLK>,
-				<&gcc GCC_BLSP1_QUP4_I2C_APPS_CLK>;
+				 <&gcc GCC_BLSP1_QUP4_I2C_APPS_CLK>;
 			clock-names = "iface", "core";
 			pinctrl-names = "default", "sleep";
 			pinctrl-0 = <&i2c4_default>;
@@ -487,10 +487,10 @@
 
 		blsp_i2c6: i2c@78ba000 {
 			compatible = "qcom,i2c-qup-v2.2.1";
-			reg = <0x78ba000 0x1000>;
+			reg = <0x078ba000 0x500>;
 			interrupts = <GIC_SPI 100 0>;
 			clocks = <&gcc GCC_BLSP1_AHB_CLK>,
-				<&gcc GCC_BLSP1_QUP6_I2C_APPS_CLK>;
+				 <&gcc GCC_BLSP1_QUP6_I2C_APPS_CLK>;
 			clock-names = "iface", "core";
 			pinctrl-names = "default", "sleep";
 			pinctrl-0 = <&i2c6_default>;
@@ -906,6 +906,7 @@
 					    "dsi_phy_regulator";
 
 				#clock-cells = <1>;
+				#phy-cells = <0>;
 
 				clocks = <&gcc GCC_MDSS_AHB_CLK>;
 				clock-names = "iface_clk";
@@ -1435,8 +1436,8 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 
-		qcom,ipc-1 = <&apcs 0 13>;
-		qcom,ipc-6 = <&apcs 0 19>;
+		qcom,ipc-1 = <&apcs 8 13>;
+		qcom,ipc-3 = <&apcs 8 19>;
 
 		apps_smsm: apps@0 {
 			reg = <0>;

arch/arm64/boot/dts/qcom/pm8916.dtsi

@@ -97,47 +97,45 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 
-                wcd_codec: codec@f000 {
-                       compatible = "qcom,pm8916-wcd-analog-codec";
-	               reg = <0xf000 0x200>;
-	               reg-names = "pmic-codec-core";
-	               clocks = <&gcc GCC_CODEC_DIGCODEC_CLK>;
-	               clock-names = "mclk";
-	               interrupt-parent = <&spmi_bus>;
-	               interrupts = <0x1 0xf0 0x0 IRQ_TYPE_NONE>,
-	                            <0x1 0xf0 0x1 IRQ_TYPE_NONE>,
-	                            <0x1 0xf0 0x2 IRQ_TYPE_NONE>,
-	                            <0x1 0xf0 0x3 IRQ_TYPE_NONE>,
-	                            <0x1 0xf0 0x4 IRQ_TYPE_NONE>,
-	                            <0x1 0xf0 0x5 IRQ_TYPE_NONE>,
-	                            <0x1 0xf0 0x6 IRQ_TYPE_NONE>,
-	                            <0x1 0xf0 0x7 IRQ_TYPE_NONE>,
-	                            <0x1 0xf1 0x0 IRQ_TYPE_NONE>,
-	                            <0x1 0xf1 0x1 IRQ_TYPE_NONE>,
-	                            <0x1 0xf1 0x2 IRQ_TYPE_NONE>,
-	                            <0x1 0xf1 0x3 IRQ_TYPE_NONE>,
-	                            <0x1 0xf1 0x4 IRQ_TYPE_NONE>,
-	                            <0x1 0xf1 0x5 IRQ_TYPE_NONE>;
-	               interrupt-names = "cdc_spk_cnp_int",
-	                                 "cdc_spk_clip_int",
-	                                 "cdc_spk_ocp_int",
-	                                 "mbhc_ins_rem_det1",
-	                                 "mbhc_but_rel_det",
-	                                 "mbhc_but_press_det",
-	                                 "mbhc_ins_rem_det",
-	                                 "mbhc_switch_int",
-	                                 "cdc_ear_ocp_int",
-	                                 "cdc_hphr_ocp_int",
-	                                 "cdc_hphl_ocp_det",
-	                                 "cdc_ear_cnp_int",
-	                                 "cdc_hphr_cnp_int",
-	                                 "cdc_hphl_cnp_int";
-	               vdd-cdc-io-supply = <&pm8916_l5>;
-	               vdd-cdc-tx-rx-cx-supply = <&pm8916_l5>;
-	               vdd-micbias-supply = <&pm8916_l13>;
-	               #sound-dai-cells = <1>;
-
-                };
-
+		wcd_codec: codec@f000 {
+			compatible = "qcom,pm8916-wcd-analog-codec";
+			reg = <0xf000 0x200>;
+			reg-names = "pmic-codec-core";
+			clocks = <&gcc GCC_CODEC_DIGCODEC_CLK>;
+			clock-names = "mclk";
+			interrupt-parent = <&spmi_bus>;
+			interrupts = <0x1 0xf0 0x0 IRQ_TYPE_NONE>,
+				     <0x1 0xf0 0x1 IRQ_TYPE_NONE>,
+				     <0x1 0xf0 0x2 IRQ_TYPE_NONE>,
+				     <0x1 0xf0 0x3 IRQ_TYPE_NONE>,
+				     <0x1 0xf0 0x4 IRQ_TYPE_NONE>,
+				     <0x1 0xf0 0x5 IRQ_TYPE_NONE>,
+				     <0x1 0xf0 0x6 IRQ_TYPE_NONE>,
+				     <0x1 0xf0 0x7 IRQ_TYPE_NONE>,
+				     <0x1 0xf1 0x0 IRQ_TYPE_NONE>,
+				     <0x1 0xf1 0x1 IRQ_TYPE_NONE>,
+				     <0x1 0xf1 0x2 IRQ_TYPE_NONE>,
+				     <0x1 0xf1 0x3 IRQ_TYPE_NONE>,
+				     <0x1 0xf1 0x4 IRQ_TYPE_NONE>,
+				     <0x1 0xf1 0x5 IRQ_TYPE_NONE>;
+			interrupt-names = "cdc_spk_cnp_int",
+					  "cdc_spk_clip_int",
+					  "cdc_spk_ocp_int",
+					  "mbhc_ins_rem_det1",
+					  "mbhc_but_rel_det",
+					  "mbhc_but_press_det",
+					  "mbhc_ins_rem_det",
+					  "mbhc_switch_int",
+					  "cdc_ear_ocp_int",
+					  "cdc_hphr_ocp_int",
+					  "cdc_hphl_ocp_det",
+					  "cdc_ear_cnp_int",
+					  "cdc_hphr_cnp_int",
+					  "cdc_hphl_cnp_int";
+			vdd-cdc-io-supply = <&pm8916_l5>;
+			vdd-cdc-tx-rx-cx-supply = <&pm8916_l5>;
+			vdd-micbias-supply = <&pm8916_l13>;
+			#sound-dai-cells = <1>;
+		};
 	};
 };

arch/arm64/boot/dts/renesas/Makefile

@@ -6,5 +6,6 @@ dtb-$(CONFIG_ARCH_R8A7795) += r8a7795-es1-salvator-x.dtb r8a7795-es1-h3ulcb.dtb
 dtb-$(CONFIG_ARCH_R8A7795) += r8a7795-es1-h3ulcb-kf.dtb
 dtb-$(CONFIG_ARCH_R8A7796) += r8a7796-salvator-x.dtb r8a7796-m3ulcb.dtb
 dtb-$(CONFIG_ARCH_R8A7796) += r8a7796-m3ulcb-kf.dtb
-dtb-$(CONFIG_ARCH_R8A77970) += r8a77970-eagle.dtb
+dtb-$(CONFIG_ARCH_R8A7796) += r8a7796-salvator-xs.dtb
+dtb-$(CONFIG_ARCH_R8A77970) += r8a77970-eagle.dtb r8a77970-v3msk.dtb
 dtb-$(CONFIG_ARCH_R8A77995) += r8a77995-draak.dtb

arch/arm64/boot/dts/renesas/r8a7795-es1-salvator-x.dts

@@ -1,5 +1,5 @@
 /*
- * Device Tree Source for the Salvator-X board
+ * Device Tree Source for the Salvator-X board with R-Car H3 ES1.x
  *
  * Copyright (C) 2015 Renesas Electronics Corp.
  *

arch/arm64/boot/dts/renesas/r8a7795-es1.dtsi

@@ -21,6 +21,26 @@
 		status = "disabled";
 	};
 
+	/delete-node/ mmu@febe0000;
+	/delete-node/ mmu@fe980000;
+	/delete-node/ mmu@fd960000;
+	/delete-node/ mmu@fd970000;
+
+	ipmmu_mp1: mmu@ec680000 {
+		compatible = "renesas,ipmmu-r8a7795";
+		reg = <0 0xec680000 0 0x1000>;
+		renesas,ipmmu-main = <&ipmmu_mm 5>;
+		#iommu-cells = <1>;
+	};
+
+	ipmmu_sy: mmu@e7730000 {
+		compatible = "renesas,ipmmu-r8a7795";
+		reg = <0 0xe7730000 0 0x1000>;
+		renesas,ipmmu-main = <&ipmmu_mm 8>;
+		#iommu-cells = <1>;
+		status = "disabled";
+	};
+
 	/delete-node/ usb-phy@ee0e0200;
 	/delete-node/ usb@ee0e0100;
 	/delete-node/ usb@ee0e0000;
@@ -35,6 +55,7 @@
 		clocks = <&cpg CPG_MOD 613>;
 		power-domains = <&sysc R8A7795_PD_A3VP>;
 		resets = <&cpg 613>;
+		iommus = <&ipmmu_vp0 2>;
 	};
 
 	vspi2: vsp@fe9c0000 {
@@ -54,6 +75,7 @@
 		clocks = <&cpg CPG_MOD 609>;
 		power-domains = <&sysc R8A7795_PD_A3VP>;
 		resets = <&cpg 609>;
+		iommus = <&ipmmu_vp0 10>;
 	};
 
 	vspd3: vsp@fea38000 {
@@ -73,6 +95,7 @@
 		clocks = <&cpg CPG_MOD 600>;
 		power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
 		resets = <&cpg 600>;
+		iommus = <&ipmmu_vi0 11>;
 	};
 
 	fdp1@fe948000 {
@@ -86,6 +109,68 @@
 	};
 };
 
+&gpio1 {
+	gpio-ranges = <&pfc 0 32 28>;
+};
+
+&ipmmu_vi0 {
+	renesas,ipmmu-main = <&ipmmu_mm 11>;
+};
+
+&ipmmu_vp0 {
+	renesas,ipmmu-main = <&ipmmu_mm 12>;
+};
+
+&ipmmu_vc0 {
+	renesas,ipmmu-main = <&ipmmu_mm 9>;
+};
+
+&ipmmu_vc1 {
+	renesas,ipmmu-main = <&ipmmu_mm 10>;
+};
+
+&ipmmu_rt {
+	renesas,ipmmu-main = <&ipmmu_mm 7>;
+};
+
+&audma0 {
+	iommus = <&ipmmu_mp1 0>, <&ipmmu_mp1 1>,
+	       <&ipmmu_mp1 2>, <&ipmmu_mp1 3>,
+	       <&ipmmu_mp1 4>, <&ipmmu_mp1 5>,
+	       <&ipmmu_mp1 6>, <&ipmmu_mp1 7>,
+	       <&ipmmu_mp1 8>, <&ipmmu_mp1 9>,
+	       <&ipmmu_mp1 10>, <&ipmmu_mp1 11>,
+	       <&ipmmu_mp1 12>, <&ipmmu_mp1 13>,
+	       <&ipmmu_mp1 14>, <&ipmmu_mp1 15>;
+};
+
+&audma1 {
+	iommus = <&ipmmu_mp1 16>, <&ipmmu_mp1 17>,
+	       <&ipmmu_mp1 18>, <&ipmmu_mp1 19>,
+	       <&ipmmu_mp1 20>, <&ipmmu_mp1 21>,
+	       <&ipmmu_mp1 22>, <&ipmmu_mp1 23>,
+	       <&ipmmu_mp1 24>, <&ipmmu_mp1 25>,
+	       <&ipmmu_mp1 26>, <&ipmmu_mp1 27>,
+	       <&ipmmu_mp1 28>, <&ipmmu_mp1 29>,
+	       <&ipmmu_mp1 30>, <&ipmmu_mp1 31>;
+};
+
+&fcpvb1 {
+	iommus = <&ipmmu_vp0 7>;
+};
+
+&fcpf1 {
+	iommus = <&ipmmu_vp0 1>;
+};
+
+&fcpvi1 {
+	iommus = <&ipmmu_vp0 9>;
+};
+
+&fcpvd2 {
+	iommus = <&ipmmu_vi0 10>;
+};
+
 &du {
 	vsps = <&vspd0 &vspd1 &vspd2 &vspd3>;
 };

arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts

@@ -1,5 +1,5 @@
 /*
- * Device Tree Source for the Salvator-X board
+ * Device Tree Source for the Salvator-X board with R-Car H3 ES2.0
  *
  * Copyright (C) 2015 Renesas Electronics Corp.
  *

arch/arm64/boot/dts/renesas/r8a7795-salvator-xs.dts

@@ -1,5 +1,5 @@
 /*
- * Device Tree Source for the Salvator-X 2nd version board
+ * Device Tree Source for the Salvator-X 2nd version board with R-Car H3 ES2.0
  *
  * Copyright (C) 2015-2017 Renesas Electronics Corp.
  *

arch/arm64/boot/dts/renesas/r8a7795.dtsi

@@ -30,11 +30,6 @@
 		i2c7 = &i2c_dvfs;
 	};
 
-	psci {
-		compatible = "arm,psci-1.0", "arm,psci-0.2";
-		method = "smc";
-	};
-
 	cpus {
 		#address-cells = <1>;
 		#size-cells = <0>;
@@ -184,6 +179,35 @@
 		clock-frequency = <0>;
 	};
 
+	pmu_a57 {
+		compatible = "arm,cortex-a57-pmu";
+		interrupts-extended = <&gic GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>,
+		                      <&gic GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>,
+				      <&gic GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>,
+				      <&gic GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&a57_0>,
+				     <&a57_1>,
+				     <&a57_2>,
+				     <&a57_3>;
+	};
+
+	pmu_a53 {
+		compatible = "arm,cortex-a53-pmu";
+		interrupts-extended = <&gic GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>,
+				      <&gic GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>,
+				      <&gic GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>,
+				      <&gic GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&a53_0>,
+				     <&a53_1>,
+				     <&a53_2>,
+				     <&a53_3>;
+	};
+
+	psci {
+		compatible = "arm,psci-1.0", "arm,psci-0.2";
+		method = "smc";
+	};
+
 	soc: soc {
 		compatible = "simple-bus";
 		interrupt-parent = <&gic>;
@@ -240,7 +264,7 @@
 			interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
 			#gpio-cells = <2>;
 			gpio-controller;
-			gpio-ranges = <&pfc 0 32 28>;
+			gpio-ranges = <&pfc 0 32 29>;
 			#interrupt-cells = <2>;
 			interrupt-controller;
 			clocks = <&cpg CPG_MOD 911>;
@@ -338,42 +362,6 @@
 			resets = <&cpg 905>;
 		};
 
-		pmu_a57 {
-			compatible = "arm,cortex-a57-pmu";
-			interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-affinity = <&a57_0>,
-					     <&a57_1>,
-					     <&a57_2>,
-					     <&a57_3>;
-		};
-
-		pmu_a53 {
-			compatible = "arm,cortex-a53-pmu";
-			interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-affinity = <&a53_0>,
-					     <&a53_1>,
-					     <&a53_2>,
-					     <&a53_3>;
-		};
-
-		timer {
-			compatible = "arm,armv8-timer";
-			interrupts = <GIC_PPI 13
-					(GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
-				     <GIC_PPI 14
-					(GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
-				     <GIC_PPI 11
-					(GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
-				     <GIC_PPI 10
-					(GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>;
-		};
-
 		cpg: clock-controller@e6150000 {
 			compatible = "renesas,r8a7795-cpg-mssr";
 			reg = <0 0xe6150000 0 0x1000>;
@@ -421,6 +409,146 @@
 			resets = <&cpg 407>;
 		};
 
+		ipmmu_vi0: mmu@febd0000 {
+			compatible = "renesas,ipmmu-r8a7795";
+			reg = <0 0xfebd0000 0 0x1000>;
+			renesas,ipmmu-main = <&ipmmu_mm 14>;
+			power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
+			#iommu-cells = <1>;
+		};
+
+		ipmmu_vi1: mmu@febe0000 {
+			compatible = "renesas,ipmmu-r8a7795";
+			reg = <0 0xfebe0000 0 0x1000>;
+			renesas,ipmmu-main = <&ipmmu_mm 15>;
+			power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
+			#iommu-cells = <1>;
+			status = "disabled";
+		};
+
+		ipmmu_vp0: mmu@fe990000 {
+			compatible = "renesas,ipmmu-r8a7795";
+			reg = <0 0xfe990000 0 0x1000>;
+			renesas,ipmmu-main = <&ipmmu_mm 16>;
+			power-domains = <&sysc R8A7795_PD_A3VP>;
+			#iommu-cells = <1>;
+			status = "disabled";
+		};
+
+		ipmmu_vp1: mmu@fe980000 {
+			compatible = "renesas,ipmmu-r8a7795";
+			reg = <0 0xfe980000 0 0x1000>;
+			renesas,ipmmu-main = <&ipmmu_mm 17>;
+			power-domains = <&sysc R8A7795_PD_A3VP>;
+			#iommu-cells = <1>;
+		};
+
+		ipmmu_vc0: mmu@fe6b0000 {
+			compatible = "renesas,ipmmu-r8a7795";
+			reg = <0 0xfe6b0000 0 0x1000>;
+			renesas,ipmmu-main = <&ipmmu_mm 12>;
+			power-domains = <&sysc R8A7795_PD_A3VC>;
+			#iommu-cells = <1>;
+			status = "disabled";
+		};
+
+		ipmmu_vc1: mmu@fe6f0000 {
+			compatible = "renesas,ipmmu-r8a7795";
+			reg = <0 0xfe6f0000 0 0x1000>;
+			renesas,ipmmu-main = <&ipmmu_mm 13>;
+			power-domains = <&sysc R8A7795_PD_A3VC>;
+			#iommu-cells = <1>;
+			status = "disabled";
+		};
+
+		ipmmu_pv0: mmu@fd800000 {
+			compatible = "renesas,ipmmu-r8a7795";
+			reg = <0 0xfd800000 0 0x1000>;
+			renesas,ipmmu-main = <&ipmmu_mm 6>;
+			power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
+			#iommu-cells = <1>;
+			status = "disabled";
+		};
+
+		ipmmu_pv2: mmu@fd960000 {
+			compatible = "renesas,ipmmu-r8a7795";
+			reg = <0 0xfd960000 0 0x1000>;
+			renesas,ipmmu-main = <&ipmmu_mm 8>;
+			power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
+			#iommu-cells = <1>;
+			status = "disabled";
+		};
+
+		ipmmu_pv3: mmu@fd970000 {
+			compatible = "renesas,ipmmu-r8a7795";
+			reg = <0 0xfd970000 0 0x1000>;
+			renesas,ipmmu-main = <&ipmmu_mm 9>;
+			power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
+			#iommu-cells = <1>;
+			status = "disabled";
+		};
+
+		ipmmu_ir: mmu@ff8b0000 {
+			compatible = "renesas,ipmmu-r8a7795";
+			reg = <0 0xff8b0000 0 0x1000>;
+			renesas,ipmmu-main = <&ipmmu_mm 3>;
+			power-domains = <&sysc R8A7795_PD_A3IR>;
+			#iommu-cells = <1>;
+			status = "disabled";
+		};
+
+		ipmmu_hc: mmu@e6570000 {
+			compatible = "renesas,ipmmu-r8a7795";
+			reg = <0 0xe6570000 0 0x1000>;
+			renesas,ipmmu-main = <&ipmmu_mm 2>;
+			power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
+			#iommu-cells = <1>;
+			status = "disabled";
+		};
+
+		ipmmu_rt: mmu@ffc80000 {
+			compatible = "renesas,ipmmu-r8a7795";
+			reg = <0 0xffc80000 0 0x1000>;
+			renesas,ipmmu-main = <&ipmmu_mm 10>;
+			power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
+			#iommu-cells = <1>;
+			status = "disabled";
+		};
+
+		ipmmu_mp0: mmu@ec670000 {
+			compatible = "renesas,ipmmu-r8a7795";
+			reg = <0 0xec670000 0 0x1000>;
+			renesas,ipmmu-main = <&ipmmu_mm 4>;
+			power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
+			#iommu-cells = <1>;
+			status = "disabled";
+		};
+
+		ipmmu_ds0: mmu@e6740000 {
+			compatible = "renesas,ipmmu-r8a7795";
+			reg = <0 0xe6740000 0 0x1000>;
+			renesas,ipmmu-main = <&ipmmu_mm 0>;
+			power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
+			#iommu-cells = <1>;
+		};
+
+		ipmmu_ds1: mmu@e7740000 {
+			compatible = "renesas,ipmmu-r8a7795";
+			reg = <0 0xe7740000 0 0x1000>;
+			renesas,ipmmu-main = <&ipmmu_mm 1>;
+			power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
+			#iommu-cells = <1>;
+		};
+
+		ipmmu_mm: mmu@e67b0000 {
+			compatible = "renesas,ipmmu-r8a7795";
+			reg = <0 0xe67b0000 0 0x1000>;
+			interrupts = <GIC_SPI 196 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 197 IRQ_TYPE_LEVEL_HIGH>;
+			power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
+			#iommu-cells = <1>;
+		};
+
 		dmac0: dma-controller@e6700000 {
 			compatible = "renesas,dmac-r8a7795",
 				     "renesas,rcar-dmac";
@@ -453,6 +581,14 @@
 			resets = <&cpg 219>;
 			#dma-cells = <1>;
 			dma-channels = <16>;
+			iommus = <&ipmmu_ds0 0>, <&ipmmu_ds0 1>,
+			       <&ipmmu_ds0 2>, <&ipmmu_ds0 3>,
+			       <&ipmmu_ds0 4>, <&ipmmu_ds0 5>,
+			       <&ipmmu_ds0 6>, <&ipmmu_ds0 7>,
+			       <&ipmmu_ds0 8>, <&ipmmu_ds0 9>,
+			       <&ipmmu_ds0 10>, <&ipmmu_ds0 11>,
+			       <&ipmmu_ds0 12>, <&ipmmu_ds0 13>,
+			       <&ipmmu_ds0 14>, <&ipmmu_ds0 15>;
 		};
 
 		dmac1: dma-controller@e7300000 {
@@ -487,6 +623,14 @@
 			resets = <&cpg 218>;
 			#dma-cells = <1>;
 			dma-channels = <16>;
+			iommus = <&ipmmu_ds1 0>, <&ipmmu_ds1 1>,
+			       <&ipmmu_ds1 2>, <&ipmmu_ds1 3>,
+			       <&ipmmu_ds1 4>, <&ipmmu_ds1 5>,
+			       <&ipmmu_ds1 6>, <&ipmmu_ds1 7>,
+			       <&ipmmu_ds1 8>, <&ipmmu_ds1 9>,
+			       <&ipmmu_ds1 10>, <&ipmmu_ds1 11>,
+			       <&ipmmu_ds1 12>, <&ipmmu_ds1 13>,
+			       <&ipmmu_ds1 14>, <&ipmmu_ds1 15>;
 		};
 
 		dmac2: dma-controller@e7310000 {
@@ -521,6 +665,14 @@
 			resets = <&cpg 217>;
 			#dma-cells = <1>;
 			dma-channels = <16>;
+			iommus = <&ipmmu_ds1 16>, <&ipmmu_ds1 17>,
+			       <&ipmmu_ds1 18>, <&ipmmu_ds1 19>,
+			       <&ipmmu_ds1 20>, <&ipmmu_ds1 21>,
+			       <&ipmmu_ds1 22>, <&ipmmu_ds1 23>,
+			       <&ipmmu_ds1 24>, <&ipmmu_ds1 25>,
+			       <&ipmmu_ds1 26>, <&ipmmu_ds1 27>,
+			       <&ipmmu_ds1 28>, <&ipmmu_ds1 29>,
+			       <&ipmmu_ds1 30>, <&ipmmu_ds1 31>;
 		};
 
 		audma0: dma-controller@ec700000 {
@@ -555,6 +707,14 @@
 			resets = <&cpg 502>;
 			#dma-cells = <1>;
 			dma-channels = <16>;
+			iommus = <&ipmmu_mp0 0>, <&ipmmu_mp0 1>,
+			       <&ipmmu_mp0 2>, <&ipmmu_mp0 3>,
+			       <&ipmmu_mp0 4>, <&ipmmu_mp0 5>,
+			       <&ipmmu_mp0 6>, <&ipmmu_mp0 7>,
+			       <&ipmmu_mp0 8>, <&ipmmu_mp0 9>,
+			       <&ipmmu_mp0 10>, <&ipmmu_mp0 11>,
+			       <&ipmmu_mp0 12>, <&ipmmu_mp0 13>,
+			       <&ipmmu_mp0 14>, <&ipmmu_mp0 15>;
 		};
 
 		audma1: dma-controller@ec720000 {
@@ -589,6 +749,14 @@
 			resets = <&cpg 501>;
 			#dma-cells = <1>;
 			dma-channels = <16>;
+			iommus = <&ipmmu_mp0 16>, <&ipmmu_mp0 17>,
+			       <&ipmmu_mp0 18>, <&ipmmu_mp0 19>,
+			       <&ipmmu_mp0 20>, <&ipmmu_mp0 21>,
+			       <&ipmmu_mp0 22>, <&ipmmu_mp0 23>,
+			       <&ipmmu_mp0 24>, <&ipmmu_mp0 25>,
+			       <&ipmmu_mp0 26>, <&ipmmu_mp0 27>,
+			       <&ipmmu_mp0 28>, <&ipmmu_mp0 29>,
+			       <&ipmmu_mp0 30>, <&ipmmu_mp0 31>;
 		};
 
 		avb: ethernet@e6800000 {
@@ -631,6 +799,7 @@
 			power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
 			resets = <&cpg 812>;
 			phy-mode = "rgmii-txid";
+			iommus = <&ipmmu_ds0 16>;
 			#address-cells = <1>;
 			#size-cells = <0>;
 			status = "disabled";
@@ -1459,6 +1628,20 @@
 			power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
 			resets = <&cpg 815>;
 			status = "disabled";
+			iommus = <&ipmmu_hc 2>;
+		};
+
+		usb3_phy0: usb-phy@e65ee000 {
+			compatible = "renesas,r8a7795-usb3-phy",
+				     "renesas,rcar-gen3-usb3-phy";
+			reg = <0 0xe65ee000 0 0x90>;
+			clocks = <&cpg CPG_MOD 328>, <&usb3s0_clk>,
+				 <&usb_extal_clk>;
+			clock-names = "usb3-if", "usb3s_clk", "usb_extal";
+			power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
+			resets = <&cpg 328>;
+			#phy-cells = <0>;
+			status = "disabled";
 		};
 
 		xhci0: usb@ee000000 {
@@ -1539,7 +1722,8 @@
 		};
 
 		sdhi0: sd@ee100000 {
-			compatible = "renesas,sdhi-r8a7795";
+			compatible = "renesas,sdhi-r8a7795",
+				     "renesas,rcar-gen3-sdhi";
 			reg = <0 0xee100000 0 0x2000>;
 			interrupts = <GIC_SPI 165 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 314>;
@@ -1550,7 +1734,8 @@
 		};
 
 		sdhi1: sd@ee120000 {
-			compatible = "renesas,sdhi-r8a7795";
+			compatible = "renesas,sdhi-r8a7795",
+				     "renesas,rcar-gen3-sdhi";
 			reg = <0 0xee120000 0 0x2000>;
 			interrupts = <GIC_SPI 166 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 313>;
@@ -1561,7 +1746,8 @@
 		};
 
 		sdhi2: sd@ee140000 {
-			compatible = "renesas,sdhi-r8a7795";
+			compatible = "renesas,sdhi-r8a7795",
+				     "renesas,rcar-gen3-sdhi";
 			reg = <0 0xee140000 0 0x2000>;
 			interrupts = <GIC_SPI 167 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 312>;
@@ -1572,7 +1758,8 @@
 		};
 
 		sdhi3: sd@ee160000 {
-			compatible = "renesas,sdhi-r8a7795";
+			compatible = "renesas,sdhi-r8a7795",
+				     "renesas,rcar-gen3-sdhi";
 			reg = <0 0xee160000 0 0x2000>;
 			interrupts = <GIC_SPI 168 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 311>;
@@ -1873,6 +2060,7 @@
 			clocks = <&cpg CPG_MOD 606>;
 			power-domains = <&sysc R8A7795_PD_A3VP>;
 			resets = <&cpg 606>;
+			iommus = <&ipmmu_vp1 7>;
 		};
 
 		fcpf0: fcp@fe950000 {
@@ -1881,6 +2069,7 @@
 			clocks = <&cpg CPG_MOD 615>;
 			power-domains = <&sysc R8A7795_PD_A3VP>;
 			resets = <&cpg 615>;
+			iommus = <&ipmmu_vp0 0>;
 		};
 
 		fcpf1: fcp@fe951000 {
@@ -1889,6 +2078,7 @@
 			clocks = <&cpg CPG_MOD 614>;
 			power-domains = <&sysc R8A7795_PD_A3VP>;
 			resets = <&cpg 614>;
+			iommus = <&ipmmu_vp1 1>;
 		};
 
 		vspbd: vsp@fe960000 {
@@ -1908,6 +2098,7 @@
 			clocks = <&cpg CPG_MOD 607>;
 			power-domains = <&sysc R8A7795_PD_A3VP>;
 			resets = <&cpg 607>;
+			iommus = <&ipmmu_vp0 5>;
 		};
 
 		vspi0: vsp@fe9a0000 {
@@ -1927,6 +2118,7 @@
 			clocks = <&cpg CPG_MOD 611>;
 			power-domains = <&sysc R8A7795_PD_A3VP>;
 			resets = <&cpg 611>;
+			iommus = <&ipmmu_vp0 8>;
 		};
 
 		vspi1: vsp@fe9b0000 {
@@ -1946,6 +2138,7 @@
 			clocks = <&cpg CPG_MOD 610>;
 			power-domains = <&sysc R8A7795_PD_A3VP>;
 			resets = <&cpg 610>;
+			iommus = <&ipmmu_vp1 9>;
 		};
 
 		vspd0: vsp@fea20000 {
@@ -1965,6 +2158,7 @@
 			clocks = <&cpg CPG_MOD 603>;
 			power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
 			resets = <&cpg 603>;
+			iommus = <&ipmmu_vi0 8>;
 		};
 
 		vspd1: vsp@fea28000 {
@@ -1984,6 +2178,7 @@
 			clocks = <&cpg CPG_MOD 602>;
 			power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
 			resets = <&cpg 602>;
+			iommus = <&ipmmu_vi0 9>;
 		};
 
 		vspd2: vsp@fea30000 {
@@ -2003,6 +2198,7 @@
 			clocks = <&cpg CPG_MOD 601>;
 			power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
 			resets = <&cpg 601>;
+			iommus = <&ipmmu_vi1 10>;
 		};
 
 		fdp1@fe940000 {
@@ -2136,49 +2332,78 @@
 			#thermal-sensor-cells = <1>;
 			status = "okay";
 		};
+	};
 
-		thermal-zones {
-			sensor_thermal1: sensor-thermal1 {
-				polling-delay-passive = <250>;
-				polling-delay = <1000>;
-				thermal-sensors = <&tsc 0>;
+	timer {
+		compatible = "arm,armv8-timer";
+		interrupts-extended = <&gic GIC_PPI 13
+				       (GIC_CPU_MASK_SIMPLE(8) |
+				       IRQ_TYPE_LEVEL_LOW)>,
+				      <&gic GIC_PPI 14
+				       (GIC_CPU_MASK_SIMPLE(8) |
+				       IRQ_TYPE_LEVEL_LOW)>,
+				      <&gic GIC_PPI 11
+				       (GIC_CPU_MASK_SIMPLE(8) |
+				       IRQ_TYPE_LEVEL_LOW)>,
+				      <&gic GIC_PPI 10
+				       (GIC_CPU_MASK_SIMPLE(8) |
+				       IRQ_TYPE_LEVEL_LOW)>;
+	};
 
-				trips {
-					sensor1_crit: sensor1-crit {
-						temperature = <120000>;
-						hysteresis = <2000>;
-						type = "critical";
-					};
+	thermal-zones {
+		sensor_thermal1: sensor-thermal1 {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+			thermal-sensors = <&tsc 0>;
+
+			trips {
+				sensor1_crit: sensor1-crit {
+					temperature = <120000>;
+					hysteresis = <2000>;
+					type = "critical";
 				};
 			};
+		};
 
-			sensor_thermal2: sensor-thermal2 {
-				polling-delay-passive = <250>;
-				polling-delay = <1000>;
-				thermal-sensors = <&tsc 1>;
+		sensor_thermal2: sensor-thermal2 {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+			thermal-sensors = <&tsc 1>;
 
-				trips {
-					sensor2_crit: sensor2-crit {
-						temperature = <120000>;
-						hysteresis = <2000>;
-						type = "critical";
-					};
+			trips {
+				sensor2_crit: sensor2-crit {
+					temperature = <120000>;
+					hysteresis = <2000>;
+					type = "critical";
 				};
 			};
+		};
 
-			sensor_thermal3: sensor-thermal3 {
-				polling-delay-passive = <250>;
-				polling-delay = <1000>;
-				thermal-sensors = <&tsc 2>;
+		sensor_thermal3: sensor-thermal3 {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+			thermal-sensors = <&tsc 2>;
 
-				trips {
-					sensor3_crit: sensor3-crit {
-						temperature = <120000>;
-						hysteresis = <2000>;
-						type = "critical";
-					};
+			trips {
+				sensor3_crit: sensor3-crit {
+					temperature = <120000>;
+					hysteresis = <2000>;
+					type = "critical";
 				};
 			};
 		};
 	};
+
+	/* External USB clocks - can be overridden by the board */
+	usb3s0_clk: usb3s0 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <0>;
+	};
+
+	usb_extal_clk: usb_extal {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <0>;
+	};
 };

arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts

@@ -1,5 +1,5 @@
 /*
- * Device Tree Source for the Salvator-X board
+ * Device Tree Source for the Salvator-X board with R-Car M3-W
  *
  * Copyright (C) 2016 Renesas Electronics Corp.
  *

arch/arm64/boot/dts/renesas/r8a7796-salvator-xs.dts

@@ -0,0 +1,58 @@
+/*
+ * Device Tree Source for the Salvator-X 2nd version board with R-Car M3-W
+ *
+ * Copyright (C) 2015-2017 Renesas Electronics Corp.
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2.  This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ */
+
+/dts-v1/;
+#include "r8a7796.dtsi"
+#include "salvator-xs.dtsi"
+
+/ {
+	model = "Renesas Salvator-X 2nd version board based on r8a7796";
+	compatible = "renesas,salvator-xs", "renesas,r8a7796";
+
+	memory@48000000 {
+		device_type = "memory";
+		/* first 128MB is reserved for secure area. */
+		reg = <0x0 0x48000000 0x0 0x78000000>;
+	};
+
+	memory@600000000 {
+		device_type = "memory";
+		reg = <0x6 0x00000000 0x0 0x80000000>;
+	};
+};
+
+&du {
+	clocks = <&cpg CPG_MOD 724>,
+		 <&cpg CPG_MOD 723>,
+		 <&cpg CPG_MOD 722>,
+		 <&cpg CPG_MOD 727>,
+		 <&versaclock6 1>,
+		 <&x21_clk>,
+		 <&versaclock6 2>;
+	clock-names = "du.0", "du.1", "du.2", "lvds.0",
+		      "dclkin.0", "dclkin.1", "dclkin.2";
+};
+
+&hdmi0 {
+	status = "okay";
+
+	ports {
+		port@1 {
+			reg = <1>;
+			rcar_dw_hdmi0_out: endpoint {
+				remote-endpoint = <&hdmi0_con>;
+			};
+		};
+	};
+};
+
+&hdmi0_con {
+	remote-endpoint = <&rcar_dw_hdmi0_out>;
+};

arch/arm64/boot/dts/renesas/r8a7796.dtsi

@@ -30,9 +30,34 @@
 		i2c7 = &i2c_dvfs;
 	};
 
-	psci {
-		compatible = "arm,psci-1.0", "arm,psci-0.2";
-		method = "smc";
+	/*
+	 * The external audio clocks are configured as 0 Hz fixed frequency
+	 * clocks by default.
+	 * Boards that provide audio clocks should override them.
+	 */
+	audio_clk_a: audio_clk_a {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <0>;
+	};
+
+	audio_clk_b: audio_clk_b {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <0>;
+	};
+
+	audio_clk_c: audio_clk_c {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <0>;
+	};
+
+	/* External CAN clock - to be overridden by boards that provide it */
+	can_clk: can {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <0>;
 	};
 
 	cpus {
@@ -122,34 +147,32 @@
 		clock-frequency = <0>;
 	};
 
-	/*
-	 * The external audio clocks are configured as 0 Hz fixed frequency
-	 * clocks by default.
-	 * Boards that provide audio clocks should override them.
-	 */
-	audio_clk_a: audio_clk_a {
+	/* External PCIe clock - can be overridden by the board */
+	pcie_bus_clk: pcie_bus {
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
 		clock-frequency = <0>;
 	};
 
-	audio_clk_b: audio_clk_b {
-		compatible = "fixed-clock";
-		#clock-cells = <0>;
-		clock-frequency = <0>;
+	pmu_a57 {
+		compatible = "arm,cortex-a57-pmu";
+		interrupts-extended = <&gic GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>,
+				      <&gic GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&a57_0>, <&a57_1>;
 	};
 
-	audio_clk_c: audio_clk_c {
-		compatible = "fixed-clock";
-		#clock-cells = <0>;
-		clock-frequency = <0>;
+	pmu_a53 {
+		compatible = "arm,cortex-a53-pmu";
+		interrupts-extended = <&gic GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>,
+				      <&gic GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>,
+				      <&gic GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>,
+				      <&gic GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&a53_0>, <&a53_1>, <&a53_2>, <&a53_3>;
 	};
 
-	/* External CAN clock - to be overridden by boards that provide it */
-	can_clk: can {
-		compatible = "fixed-clock";
-		#clock-cells = <0>;
-		clock-frequency = <0>;
+	psci {
+		compatible = "arm,psci-1.0", "arm,psci-0.2";
+		method = "smc";
 	};
 
 	/* External SCIF clock - to be overridden by boards that provide it */
@@ -159,13 +182,6 @@
 		clock-frequency = <0>;
 	};
 
-	/* External PCIe clock - can be overridden by the board */
-	pcie_bus_clk: pcie_bus {
-		compatible = "fixed-clock";
-		#clock-cells = <0>;
-		clock-frequency = <0>;
-	};
-
 	soc {
 		compatible = "simple-bus";
 		interrupt-parent = <&gic>;
@@ -190,18 +206,6 @@
 			resets = <&cpg 408>;
 		};
 
-		timer {
-			compatible = "arm,armv8-timer";
-			interrupts = <GIC_PPI 13
-					(GIC_CPU_MASK_SIMPLE(6) | IRQ_TYPE_LEVEL_LOW)>,
-				     <GIC_PPI 14
-					(GIC_CPU_MASK_SIMPLE(6) | IRQ_TYPE_LEVEL_LOW)>,
-				     <GIC_PPI 11
-					(GIC_CPU_MASK_SIMPLE(6) | IRQ_TYPE_LEVEL_LOW)>,
-				     <GIC_PPI 10
-					(GIC_CPU_MASK_SIMPLE(6) | IRQ_TYPE_LEVEL_LOW)>;
-		};
-
 		wdt0: watchdog@e6020000 {
 			compatible = "renesas,r8a7796-wdt",
 				     "renesas,rcar-gen3-wdt";
@@ -337,24 +341,98 @@
 			reg = <0 0xe6060000 0 0x50c>;
 		};
 
-		pmu_a57 {
-			compatible = "arm,cortex-a57-pmu";
-			interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-affinity = <&a57_0>,
-					     <&a57_1>;
+		ipmmu_vi0: mmu@febd0000 {
+			compatible = "renesas,ipmmu-r8a7796";
+			reg = <0 0xfebd0000 0 0x1000>;
+			renesas,ipmmu-main = <&ipmmu_mm 9>;
+			power-domains = <&sysc R8A7796_PD_ALWAYS_ON>;
+			#iommu-cells = <1>;
 		};
 
-		pmu_a53 {
-			compatible = "arm,cortex-a53-pmu";
-			interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-affinity = <&a53_0>,
-					     <&a53_1>,
-					     <&a53_2>,
-					     <&a53_3>;
+		ipmmu_vc0: mmu@fe6b0000 {
+			compatible = "renesas,ipmmu-r8a7796";
+			reg = <0 0xfe6b0000 0 0x1000>;
+			renesas,ipmmu-main = <&ipmmu_mm 8>;
+			power-domains = <&sysc R8A7796_PD_A3VC>;
+			#iommu-cells = <1>;
+			status = "disabled";
+		};
+
+		ipmmu_pv0: mmu@fd800000 {
+			compatible = "renesas,ipmmu-r8a7796";
+			reg = <0 0xfd800000 0 0x1000>;
+			renesas,ipmmu-main = <&ipmmu_mm 5>;
+			power-domains = <&sysc R8A7796_PD_ALWAYS_ON>;
+			#iommu-cells = <1>;
+		};
+
+		ipmmu_pv1: mmu@fd950000 {
+			compatible = "renesas,ipmmu-r8a7796";
+			reg = <0 0xfd950000 0 0x1000>;
+			renesas,ipmmu-main = <&ipmmu_mm 6>;
+			power-domains = <&sysc R8A7796_PD_ALWAYS_ON>;
+			#iommu-cells = <1>;
+			status = "disabled";
+		};
+
+		ipmmu_ir: mmu@ff8b0000 {
+			compatible = "renesas,ipmmu-r8a7796";
+			reg = <0 0xff8b0000 0 0x1000>;
+			renesas,ipmmu-main = <&ipmmu_mm 3>;
+			power-domains = <&sysc R8A7796_PD_A3IR>;
+			#iommu-cells = <1>;
+			status = "disabled";
+		};
+
+		ipmmu_hc: mmu@e6570000 {
+			compatible = "renesas,ipmmu-r8a7796";
+			reg = <0 0xe6570000 0 0x1000>;
+			renesas,ipmmu-main = <&ipmmu_mm 2>;
+			power-domains = <&sysc R8A7796_PD_ALWAYS_ON>;
+			#iommu-cells = <1>;
+			status = "disabled";
+		};
+
+		ipmmu_rt: mmu@ffc80000 {
+			compatible = "renesas,ipmmu-r8a7796";
+			reg = <0 0xffc80000 0 0x1000>;
+			renesas,ipmmu-main = <&ipmmu_mm 7>;
+			power-domains = <&sysc R8A7796_PD_ALWAYS_ON>;
+			#iommu-cells = <1>;
+			status = "disabled";
+		};
+
+		ipmmu_mp: mmu@ec670000 {
+			compatible = "renesas,ipmmu-r8a7796";
+			reg = <0 0xec670000 0 0x1000>;
+			renesas,ipmmu-main = <&ipmmu_mm 4>;
+			power-domains = <&sysc R8A7796_PD_ALWAYS_ON>;
+			#iommu-cells = <1>;
+		};
+
+		ipmmu_ds0: mmu@e6740000 {
+			compatible = "renesas,ipmmu-r8a7796";
+			reg = <0 0xe6740000 0 0x1000>;
+			renesas,ipmmu-main = <&ipmmu_mm 0>;
+			power-domains = <&sysc R8A7796_PD_ALWAYS_ON>;
+			#iommu-cells = <1>;
+		};
+
+		ipmmu_ds1: mmu@e7740000 {
+			compatible = "renesas,ipmmu-r8a7796";
+			reg = <0 0xe7740000 0 0x1000>;
+			renesas,ipmmu-main = <&ipmmu_mm 1>;
+			power-domains = <&sysc R8A7796_PD_ALWAYS_ON>;
+			#iommu-cells = <1>;
+		};
+
+		ipmmu_mm: mmu@e67b0000 {
+			compatible = "renesas,ipmmu-r8a7796";
+			reg = <0 0xe67b0000 0 0x1000>;
+			interrupts = <GIC_SPI 196 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 197 IRQ_TYPE_LEVEL_HIGH>;
+			power-domains = <&sysc R8A7796_PD_ALWAYS_ON>;
+			#iommu-cells = <1>;
 		};
 
 		cpg: clock-controller@e6150000 {
@@ -817,6 +895,7 @@
 			power-domains = <&sysc R8A7796_PD_ALWAYS_ON>;
 			resets = <&cpg 812>;
 			phy-mode = "rgmii-txid";
+			iommus = <&ipmmu_ds0 16>;
 			#address-cells = <1>;
 			#size-cells = <0>;
 			status = "disabled";
@@ -1101,6 +1180,14 @@
 			resets = <&cpg 219>;
 			#dma-cells = <1>;
 			dma-channels = <16>;
+			iommus = <&ipmmu_ds0 0>, <&ipmmu_ds0 1>,
+			       <&ipmmu_ds0 2>, <&ipmmu_ds0 3>,
+			       <&ipmmu_ds0 4>, <&ipmmu_ds0 5>,
+			       <&ipmmu_ds0 6>, <&ipmmu_ds0 7>,
+			       <&ipmmu_ds0 8>, <&ipmmu_ds0 9>,
+			       <&ipmmu_ds0 10>, <&ipmmu_ds0 11>,
+			       <&ipmmu_ds0 12>, <&ipmmu_ds0 13>,
+			       <&ipmmu_ds0 14>, <&ipmmu_ds0 15>;
 		};
 
 		dmac1: dma-controller@e7300000 {
@@ -1135,6 +1222,14 @@
 			resets = <&cpg 218>;
 			#dma-cells = <1>;
 			dma-channels = <16>;
+			iommus = <&ipmmu_ds1 0>, <&ipmmu_ds1 1>,
+			       <&ipmmu_ds1 2>, <&ipmmu_ds1 3>,
+			       <&ipmmu_ds1 4>, <&ipmmu_ds1 5>,
+			       <&ipmmu_ds1 6>, <&ipmmu_ds1 7>,
+			       <&ipmmu_ds1 8>, <&ipmmu_ds1 9>,
+			       <&ipmmu_ds1 10>, <&ipmmu_ds1 11>,
+			       <&ipmmu_ds1 12>, <&ipmmu_ds1 13>,
+			       <&ipmmu_ds1 14>, <&ipmmu_ds1 15>;
 		};
 
 		dmac2: dma-controller@e7310000 {
@@ -1169,6 +1264,14 @@
 			resets = <&cpg 217>;
 			#dma-cells = <1>;
 			dma-channels = <16>;
+			iommus = <&ipmmu_ds1 16>, <&ipmmu_ds1 17>,
+			       <&ipmmu_ds1 18>, <&ipmmu_ds1 19>,
+			       <&ipmmu_ds1 20>, <&ipmmu_ds1 21>,
+			       <&ipmmu_ds1 22>, <&ipmmu_ds1 23>,
+			       <&ipmmu_ds1 24>, <&ipmmu_ds1 25>,
+			       <&ipmmu_ds1 26>, <&ipmmu_ds1 27>,
+			       <&ipmmu_ds1 28>, <&ipmmu_ds1 29>,
+			       <&ipmmu_ds1 30>, <&ipmmu_ds1 31>;
 		};
 
 		audma0: dma-controller@ec700000 {
@@ -1203,6 +1306,14 @@
 			resets = <&cpg 502>;
 			#dma-cells = <1>;
 			dma-channels = <16>;
+			iommus = <&ipmmu_mp 0>, <&ipmmu_mp 1>,
+			       <&ipmmu_mp 2>, <&ipmmu_mp 3>,
+			       <&ipmmu_mp 4>, <&ipmmu_mp 5>,
+			       <&ipmmu_mp 6>, <&ipmmu_mp 7>,
+			       <&ipmmu_mp 8>, <&ipmmu_mp 9>,
+			       <&ipmmu_mp 10>, <&ipmmu_mp 11>,
+			       <&ipmmu_mp 12>, <&ipmmu_mp 13>,
+			       <&ipmmu_mp 14>, <&ipmmu_mp 15>;
 		};
 
 		audma1: dma-controller@ec720000 {
@@ -1237,6 +1348,14 @@
 			resets = <&cpg 501>;
 			#dma-cells = <1>;
 			dma-channels = <16>;
+			iommus = <&ipmmu_mp 16>, <&ipmmu_mp 17>,
+			       <&ipmmu_mp 18>, <&ipmmu_mp 19>,
+			       <&ipmmu_mp 20>, <&ipmmu_mp 21>,
+			       <&ipmmu_mp 22>, <&ipmmu_mp 23>,
+			       <&ipmmu_mp 24>, <&ipmmu_mp 25>,
+			       <&ipmmu_mp 26>, <&ipmmu_mp 27>,
+			       <&ipmmu_mp 28>, <&ipmmu_mp 29>,
+			       <&ipmmu_mp 30>, <&ipmmu_mp 31>;
 		};
 
 		usb_dmac0: dma-controller@e65a0000 {
@@ -1284,6 +1403,19 @@
 			status = "disabled";
 		};
 
+		usb3_phy0: usb-phy@e65ee000 {
+			compatible = "renesas,r8a7796-usb3-phy",
+				     "renesas,rcar-gen3-usb3-phy";
+			reg = <0 0xe65ee000 0 0x90>;
+			clocks = <&cpg CPG_MOD 328>, <&usb3s0_clk>,
+				 <&usb_extal_clk>;
+			clock-names = "usb3-if", "usb3s_clk", "usb_extal";
+			power-domains = <&sysc R8A7796_PD_ALWAYS_ON>;
+			resets = <&cpg 328>;
+			#phy-cells = <0>;
+			status = "disabled";
+		};
+
 		xhci0: usb@ee000000 {
 			compatible = "renesas,xhci-r8a7796",
 				     "renesas,rcar-gen3-xhci";
@@ -1380,7 +1512,8 @@
 		};
 
 		sdhi0: sd@ee100000 {
-			compatible = "renesas,sdhi-r8a7796";
+			compatible = "renesas,sdhi-r8a7796",
+				     "renesas,rcar-gen3-sdhi";
 			reg = <0 0xee100000 0 0x2000>;
 			interrupts = <GIC_SPI 165 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 314>;
@@ -1391,7 +1524,8 @@
 		};
 
 		sdhi1: sd@ee120000 {
-			compatible = "renesas,sdhi-r8a7796";
+			compatible = "renesas,sdhi-r8a7796",
+				     "renesas,rcar-gen3-sdhi";
 			reg = <0 0xee120000 0 0x2000>;
 			interrupts = <GIC_SPI 166 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 313>;
@@ -1402,7 +1536,8 @@
 		};
 
 		sdhi2: sd@ee140000 {
-			compatible = "renesas,sdhi-r8a7796";
+			compatible = "renesas,sdhi-r8a7796",
+				     "renesas,rcar-gen3-sdhi";
 			reg = <0 0xee140000 0 0x2000>;
 			interrupts = <GIC_SPI 167 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 312>;
@@ -1413,7 +1548,8 @@
 		};
 
 		sdhi3: sd@ee160000 {
-			compatible = "renesas,sdhi-r8a7796";
+			compatible = "renesas,sdhi-r8a7796",
+				     "renesas,rcar-gen3-sdhi";
 			reg = <0 0xee160000 0 0x2000>;
 			interrupts = <GIC_SPI 168 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 311>;
@@ -1438,50 +1574,6 @@
 			status = "okay";
 		};
 
-		thermal-zones {
-			sensor_thermal1: sensor-thermal1 {
-				polling-delay-passive = <250>;
-				polling-delay = <1000>;
-				thermal-sensors = <&tsc 0>;
-
-				trips {
-					sensor1_crit: sensor1-crit {
-						temperature = <120000>;
-						hysteresis = <2000>;
-						type = "critical";
-					};
-				};
-			};
-
-			sensor_thermal2: sensor-thermal2 {
-				polling-delay-passive = <250>;
-				polling-delay = <1000>;
-				thermal-sensors = <&tsc 1>;
-
-				trips {
-					sensor2_crit: sensor2-crit {
-						temperature = <120000>;
-						hysteresis = <2000>;
-						type = "critical";
-					};
-				};
-			};
-
-			sensor_thermal3: sensor-thermal3 {
-				polling-delay-passive = <250>;
-				polling-delay = <1000>;
-				thermal-sensors = <&tsc 2>;
-
-				trips {
-					sensor3_crit: sensor3-crit {
-						temperature = <120000>;
-						hysteresis = <2000>;
-						type = "critical";
-					};
-				};
-			};
-		};
-
 		rcar_sound: sound@ec500000 {
 			/*
 			 * #sound-dai-cells is required
@@ -1679,10 +1771,12 @@
 		};
 
 		pciec0: pcie@fe000000 {
+			reg = <0 0xfe000000 0 0x80000>;
 			/* placeholder */
 		};
 
 		pciec1: pcie@ee800000 {
+			reg = <0 0xee800000 0 0x80000>;
 			/* placeholder */
 		};
 
@@ -1740,6 +1834,7 @@
 			clocks = <&cpg CPG_MOD 611>;
 			power-domains = <&sysc R8A7796_PD_A3VC>;
 			resets = <&cpg 611>;
+			iommus = <&ipmmu_vc0 19>;
 		};
 
 		vspd0: vsp@fea20000 {
@@ -1759,6 +1854,7 @@
 			clocks = <&cpg CPG_MOD 603>;
 			power-domains = <&sysc R8A7796_PD_ALWAYS_ON>;
 			resets = <&cpg 603>;
+			iommus = <&ipmmu_vi0 8>;
 		};
 
 		vspd1: vsp@fea28000 {
@@ -1778,6 +1874,7 @@
 			clocks = <&cpg CPG_MOD 602>;
 			power-domains = <&sysc R8A7796_PD_ALWAYS_ON>;
 			resets = <&cpg 602>;
+			iommus = <&ipmmu_vi0 9>;
 		};
 
 		vspd2: vsp@fea30000 {
@@ -1797,6 +1894,7 @@
 			clocks = <&cpg CPG_MOD 601>;
 			power-domains = <&sysc R8A7796_PD_ALWAYS_ON>;
 			resets = <&cpg 601>;
+			iommus = <&ipmmu_vi0 10>;
 		};
 
 		hdmi0: hdmi@fead0000 {
@@ -1884,4 +1982,69 @@
 			resets = <&cpg 822>;
 		};
 	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		interrupts-extended = <&gic GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(6) | IRQ_TYPE_LEVEL_LOW)>,
+				      <&gic GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(6) | IRQ_TYPE_LEVEL_LOW)>,
+				      <&gic GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(6) | IRQ_TYPE_LEVEL_LOW)>,
+				      <&gic GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(6) | IRQ_TYPE_LEVEL_LOW)>;
+	};
+
+	thermal-zones {
+		sensor_thermal1: sensor-thermal1 {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+			thermal-sensors = <&tsc 0>;
+
+			trips {
+				sensor1_crit: sensor1-crit {
+					temperature = <120000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+
+		sensor_thermal2: sensor-thermal2 {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+			thermal-sensors = <&tsc 1>;
+
+			trips {
+				sensor2_crit: sensor2-crit {
+					temperature = <120000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+
+		sensor_thermal3: sensor-thermal3 {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+			thermal-sensors = <&tsc 2>;
+
+			trips {
+				sensor3_crit: sensor3-crit {
+					temperature = <120000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+	};
+
+	/* External USB clocks - can be overridden by the board */
+	usb3s0_clk: usb3s0 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <0>;
+	};
+
+	usb_extal_clk: usb_extal {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <0>;
+	};
 };

arch/arm64/boot/dts/renesas/r8a77970-eagle.dts

@@ -33,18 +33,6 @@
 	};
 };
 
-&extal_clk {
-	clock-frequency = <16666666>;
-};
-
-&extalr_clk {
-	clock-frequency = <32768>;
-};
-
-&scif0 {
-	status = "okay";
-};
-
 &avb {
 	renesas,no-ether-link;
 	phy-handle = <&phy0>;
@@ -55,3 +43,20 @@
 		reg = <0>;
 	};
 };
+
+&extal_clk {
+	clock-frequency = <16666666>;
+};
+
+&extalr_clk {
+	clock-frequency = <32768>;
+};
+
+&rwdt {
+	timeout-sec = <60>;
+	status = "okay";
+};
+
+&scif0 {
+	status = "okay";
+};

arch/arm64/boot/dts/renesas/r8a77970-v3msk.dts

@@ -0,0 +1,55 @@
+/*
+ * Device Tree Source for the V3M Starter Kit board
+ *
+ * Copyright (C) 2017 Renesas Electronics Corp.
+ * Copyright (C) 2017 Cogent Embedded, Inc.
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2.  This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ */
+
+/dts-v1/;
+#include "r8a77970.dtsi"
+
+/ {
+	model = "Renesas V3M Starter Kit board";
+	compatible = "renesas,v3msk", "renesas,r8a77970";
+
+	aliases {
+		serial0 = &scif0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@48000000 {
+		device_type = "memory";
+		/* first 128MB is reserved for secure area. */
+		reg = <0x0 0x48000000 0x0 0x38000000>;
+	};
+};
+
+&avb {
+	renesas,no-ether-link;
+	phy-handle = <&phy0>;
+	status = "okay";
+
+	phy0: ethernet-phy@0 {
+		rxc-skew-ps = <1500>;
+		reg = <0>;
+	};
+};
+
+&extal_clk {
+	clock-frequency = <16666666>;
+};
+
+&extalr_clk {
+	clock-frequency = <32768>;
+};
+
+&scif0 {
+	status = "okay";
+};

arch/arm64/boot/dts/renesas/r8a77970.dtsi

@@ -9,9 +9,10 @@
  * kind, whether express or implied.
  */
 
-#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/clock/r8a77970-cpg-mssr.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
-#include <dt-bindings/clock/renesas-cpg-mssr.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/power/r8a77970-sysc.h>
 
 / {
 	compatible = "renesas,r8a77970";
@@ -31,15 +32,15 @@
 			device_type = "cpu";
 			compatible = "arm,cortex-a53", "arm,armv8";
 			reg = <0>;
-			clocks = <&cpg CPG_CORE 0>;
-			power-domains = <&sysc 5>;
+			clocks = <&cpg CPG_CORE R8A77970_CLK_Z2>;
+			power-domains = <&sysc R8A77970_PD_CA53_CPU0>;
 			next-level-cache = <&L2_CA53>;
 			enable-method = "psci";
 		};
 
 		L2_CA53: cache-controller {
 			compatible = "cache";
-			power-domains = <&sysc 21>;
+			power-domains = <&sysc R8A77970_PD_CA53_SCU>;
 			cache-unified;
 			cache-level = <2>;
 		};
@@ -87,7 +88,7 @@
 				      IRQ_TYPE_LEVEL_HIGH)>;
 			clocks = <&cpg CPG_MOD 408>;
 			clock-names = "clk";
-			power-domains = <&sysc 32>;
+			power-domains = <&sysc R8A77970_PD_ALWAYS_ON>;
 			resets = <&cpg 408>;
 		};
 
@@ -103,6 +104,16 @@
 						  IRQ_TYPE_LEVEL_LOW)>;
 		};
 
+		rwdt: watchdog@e6020000 {
+			compatible = "renesas,r8a77970-wdt",
+				     "renesas,rcar-gen3-wdt";
+			reg = <0 0xe6020000 0 0x0c>;
+			clocks = <&cpg CPG_MOD 402>;
+			power-domains = <&sysc R8A77970_PD_ALWAYS_ON>;
+			resets = <&cpg 402>;
+			status = "disabled";
+		};
+
 		cpg: clock-controller@e6150000 {
 			compatible = "renesas,r8a77970-cpg-mssr";
 			reg = <0 0xe6150000 0 0x1000>;
@@ -124,6 +135,49 @@
 			#power-domain-cells = <1>;
 		};
 
+		ipmmu_vi0: mmu@febd0000 {
+			compatible = "renesas,ipmmu-r8a77970";
+			reg = <0 0xfebd0000 0 0x1000>;
+			renesas,ipmmu-main = <&ipmmu_mm 9>;
+			power-domains = <&sysc R8A77970_PD_ALWAYS_ON>;
+			#iommu-cells = <1>;
+			status = "disabled";
+		};
+
+		ipmmu_ir: mmu@ff8b0000 {
+			compatible = "renesas,ipmmu-r8a77970";
+			reg = <0 0xff8b0000 0 0x1000>;
+			renesas,ipmmu-main = <&ipmmu_mm 3>;
+			power-domains = <&sysc R8A77970_PD_A3IR>;
+			#iommu-cells = <1>;
+			status = "disabled";
+		};
+
+		ipmmu_rt: mmu@ffc80000 {
+			compatible = "renesas,ipmmu-r8a77970";
+			reg = <0 0xffc80000 0 0x1000>;
+			renesas,ipmmu-main = <&ipmmu_mm 7>;
+			power-domains = <&sysc R8A77970_PD_ALWAYS_ON>;
+			#iommu-cells = <1>;
+		};
+
+		ipmmu_ds1: mmu@e7740000 {
+			compatible = "renesas,ipmmu-r8a77970";
+			reg = <0 0xe7740000 0 0x1000>;
+			renesas,ipmmu-main = <&ipmmu_mm 1>;
+			power-domains = <&sysc R8A77970_PD_ALWAYS_ON>;
+			#iommu-cells = <1>;
+		};
+
+		ipmmu_mm: mmu@e67b0000 {
+			compatible = "renesas,ipmmu-r8a77970";
+			reg = <0 0xe67b0000 0 0x1000>;
+			interrupts = <GIC_SPI 196 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 197 IRQ_TYPE_LEVEL_HIGH>;
+			power-domains = <&sysc R8A77970_PD_ALWAYS_ON>;
+			#iommu-cells = <1>;
+		};
+
 		intc_ex: interrupt-controller@e61c0000 {
 			compatible = "renesas,intc-ex-r8a77970", "renesas,irqc";
 			#interrupt-cells = <2>;
@@ -136,7 +190,7 @@
 				      GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH
 				      GIC_SPI 161 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 407>;
-			power-domains = <&sysc 32>;
+			power-domains = <&sysc R8A77970_PD_ALWAYS_ON>;
 			resets = <&cpg 407>;
 		};
 
@@ -163,10 +217,14 @@
 					  "ch4", "ch5", "ch6", "ch7";
 			clocks = <&cpg CPG_MOD 218>;
 			clock-names = "fck";
-			power-domains = <&sysc 32>;
+			power-domains = <&sysc R8A77970_PD_ALWAYS_ON>;
 			resets = <&cpg 218>;
 			#dma-cells = <1>;
 			dma-channels = <8>;
+			iommus = <&ipmmu_ds1 0>, <&ipmmu_ds1 1>,
+			       <&ipmmu_ds1 2>, <&ipmmu_ds1 3>,
+			       <&ipmmu_ds1 4>, <&ipmmu_ds1 5>,
+			       <&ipmmu_ds1 6>, <&ipmmu_ds1 7>;
 		};
 
 		dmac2: dma-controller@e7310000 {
@@ -187,10 +245,14 @@
 					  "ch4", "ch5", "ch6", "ch7";
 			clocks = <&cpg CPG_MOD 217>;
 			clock-names = "fck";
-			power-domains = <&sysc 32>;
+			power-domains = <&sysc R8A77970_PD_ALWAYS_ON>;
 			resets = <&cpg 217>;
 			#dma-cells = <1>;
 			dma-channels = <8>;
+			iommus = <&ipmmu_ds1 16>, <&ipmmu_ds1 17>,
+			       <&ipmmu_ds1 18>, <&ipmmu_ds1 19>,
+			       <&ipmmu_ds1 20>, <&ipmmu_ds1 21>,
+			       <&ipmmu_ds1 22>, <&ipmmu_ds1 23>;
 		};
 
 		hscif0: serial@e6540000 {
@@ -200,13 +262,13 @@
 			reg = <0 0xe6540000 0 96>;
 			interrupts = <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 520>,
-				 <&cpg CPG_CORE 9>,
+				 <&cpg CPG_CORE R8A77970_CLK_S2D1>,
 				 <&scif_clk>;
 			clock-names = "fck", "brg_int", "scif_clk";
 			dmas = <&dmac1 0x31>, <&dmac1 0x30>,
 			       <&dmac2 0x31>, <&dmac2 0x30>;
 			dma-names = "tx", "rx", "tx", "rx";
-			power-domains = <&sysc 32>;
+			power-domains = <&sysc R8A77970_PD_ALWAYS_ON>;
 			resets = <&cpg 520>;
 			status = "disabled";
 		};
@@ -218,13 +280,13 @@
 			reg = <0 0xe6550000 0 96>;
 			interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 519>,
-				 <&cpg CPG_CORE 9>,
+				 <&cpg CPG_CORE R8A77970_CLK_S2D1>,
 				 <&scif_clk>;
 			clock-names = "fck", "brg_int", "scif_clk";
 			dmas = <&dmac1 0x33>, <&dmac1 0x32>,
 			       <&dmac2 0x33>, <&dmac2 0x32>;
 			dma-names = "tx", "rx", "tx", "rx";
-			power-domains = <&sysc 32>;
+			power-domains = <&sysc R8A77970_PD_ALWAYS_ON>;
 			resets = <&cpg 519>;
 			status = "disabled";
 		};
@@ -236,13 +298,13 @@
 			reg = <0 0xe6560000 0 96>;
 			interrupts = <GIC_SPI 144 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 518>,
-				 <&cpg CPG_CORE 9>,
+				 <&cpg CPG_CORE R8A77970_CLK_S2D1>,
 				 <&scif_clk>;
 			clock-names = "fck", "brg_int", "scif_clk";
 			dmas = <&dmac1 0x35>, <&dmac1 0x34>,
 			       <&dmac2 0x35>, <&dmac2 0x34>;
 			dma-names = "tx", "rx", "tx", "rx";
-			power-domains = <&sysc 32>;
+			power-domains = <&sysc R8A77970_PD_ALWAYS_ON>;
 			resets = <&cpg 518>;
 			status = "disabled";
 		};
@@ -253,13 +315,13 @@
 			reg = <0 0xe66a0000 0 96>;
 			interrupts = <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 517>,
-				 <&cpg CPG_CORE 9>,
+				 <&cpg CPG_CORE R8A77970_CLK_S2D1>,
 				 <&scif_clk>;
 			clock-names = "fck", "brg_int", "scif_clk";
 			dmas = <&dmac1 0x37>, <&dmac1 0x36>,
 			       <&dmac2 0x37>, <&dmac2 0x36>;
 			dma-names = "tx", "rx", "tx", "rx";
-			power-domains = <&sysc 32>;
+			power-domains = <&sysc R8A77970_PD_ALWAYS_ON>;
 			resets = <&cpg 517>;
 			status = "disabled";
 		};
@@ -271,13 +333,13 @@
 			reg = <0 0xe6e60000 0 64>;
 			interrupts = <GIC_SPI 152 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 207>,
-				 <&cpg CPG_CORE 9>,
+				 <&cpg CPG_CORE R8A77970_CLK_S2D1>,
 				 <&scif_clk>;
 			clock-names = "fck", "brg_int", "scif_clk";
 			dmas = <&dmac1 0x51>, <&dmac1 0x50>,
 			       <&dmac2 0x51>, <&dmac2 0x50>;
 			dma-names = "tx", "rx", "tx", "rx";
-			power-domains = <&sysc 32>;
+			power-domains = <&sysc R8A77970_PD_ALWAYS_ON>;
 			resets = <&cpg 207>;
 			status = "disabled";
 		};
@@ -289,13 +351,13 @@
 			reg = <0 0xe6e68000 0 64>;
 			interrupts = <GIC_SPI 153 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 206>,
-				 <&cpg CPG_CORE 9>,
+				 <&cpg CPG_CORE R8A77970_CLK_S2D1>,
 				 <&scif_clk>;
 			clock-names = "fck", "brg_int", "scif_clk";
 			dmas = <&dmac1 0x53>, <&dmac1 0x52>,
 			       <&dmac2 0x53>, <&dmac2 0x52>;
 			dma-names = "tx", "rx", "tx", "rx";
-			power-domains = <&sysc 32>;
+			power-domains = <&sysc R8A77970_PD_ALWAYS_ON>;
 			resets = <&cpg 206>;
 			status = "disabled";
 		};
@@ -307,13 +369,13 @@
 			reg = <0 0xe6c50000 0 64>;
 			interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 204>,
-				 <&cpg CPG_CORE 9>,
+				 <&cpg CPG_CORE R8A77970_CLK_S2D1>,
 				 <&scif_clk>;
 			clock-names = "fck", "brg_int", "scif_clk";
 			dmas = <&dmac1 0x57>, <&dmac1 0x56>,
 			       <&dmac2 0x57>, <&dmac2 0x56>;
 			dma-names = "tx", "rx", "tx", "rx";
-			power-domains = <&sysc 32>;
+			power-domains = <&sysc R8A77970_PD_ALWAYS_ON>;
 			resets = <&cpg 204>;
 			status = "disabled";
 		};
@@ -324,13 +386,13 @@
 			reg = <0 0xe6c40000 0 64>;
 			interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 203>,
-				 <&cpg CPG_CORE 9>,
+				 <&cpg CPG_CORE R8A77970_CLK_S2D1>,
 				 <&scif_clk>;
 			clock-names = "fck", "brg_int", "scif_clk";
 			dmas = <&dmac1 0x59>, <&dmac1 0x58>,
 			       <&dmac2 0x59>, <&dmac2 0x58>;
 			dma-names = "tx", "rx", "tx", "rx";
-			power-domains = <&sysc 32>;
+			power-domains = <&sysc R8A77970_PD_ALWAYS_ON>;
 			resets = <&cpg 203>;
 			status = "disabled";
 		};
@@ -372,9 +434,10 @@
 					  "ch20", "ch21", "ch22", "ch23",
 					  "ch24";
 			clocks = <&cpg CPG_MOD 812>;
-			power-domains = <&sysc 32>;
+			power-domains = <&sysc R8A77970_PD_ALWAYS_ON>;
 			resets = <&cpg 812>;
 			phy-mode = "rgmii-id";
+			iommus = <&ipmmu_rt 3>;
 			#address-cells = <1>;
 			#size-cells = <0>;
 		};

arch/arm64/boot/dts/renesas/r8a77995.dtsi

@@ -51,6 +51,13 @@
 		clock-frequency = <0>;
 	};
 
+	/* External CAN clock - to be overridden by boards that provide it */
+	can_clk: can {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <0>;
+	};
+
 	scif_clk: scif {
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
@@ -108,6 +115,88 @@
 			interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
 		};
 
+		ipmmu_vi0: mmu@febd0000 {
+			compatible = "renesas,ipmmu-r8a77995";
+			reg = <0 0xfebd0000 0 0x1000>;
+			renesas,ipmmu-main = <&ipmmu_mm 14>;
+			#iommu-cells = <1>;
+			status = "disabled";
+		};
+
+		ipmmu_vp0: mmu@fe990000 {
+			compatible = "renesas,ipmmu-r8a77995";
+			reg = <0 0xfe990000 0 0x1000>;
+			renesas,ipmmu-main = <&ipmmu_mm 16>;
+			#iommu-cells = <1>;
+			status = "disabled";
+		};
+
+		ipmmu_vc0: mmu@fe6b0000 {
+			compatible = "renesas,ipmmu-r8a77995";
+			reg = <0 0xfe6b0000 0 0x1000>;
+			renesas,ipmmu-main = <&ipmmu_mm 12>;
+			#iommu-cells = <1>;
+			status = "disabled";
+		};
+
+		ipmmu_pv0: mmu@fd800000 {
+			compatible = "renesas,ipmmu-r8a77995";
+			reg = <0 0xfd800000 0 0x1000>;
+			renesas,ipmmu-main = <&ipmmu_mm 6>;
+			#iommu-cells = <1>;
+			status = "disabled";
+		};
+
+		ipmmu_hc: mmu@e6570000 {
+			compatible = "renesas,ipmmu-r8a77995";
+			reg = <0 0xe6570000 0 0x1000>;
+			renesas,ipmmu-main = <&ipmmu_mm 2>;
+			#iommu-cells = <1>;
+			status = "disabled";
+		};
+
+		ipmmu_rt: mmu@ffc80000 {
+			compatible = "renesas,ipmmu-r8a77995";
+			reg = <0 0xffc80000 0 0x1000>;
+			renesas,ipmmu-main = <&ipmmu_mm 10>;
+			#iommu-cells = <1>;
+			status = "disabled";
+		};
+
+		ipmmu_mp: mmu@ec670000 {
+			compatible = "renesas,ipmmu-r8a77995";
+			reg = <0 0xec670000 0 0x1000>;
+			renesas,ipmmu-main = <&ipmmu_mm 4>;
+			#iommu-cells = <1>;
+			status = "disabled";
+		};
+
+		ipmmu_ds0: mmu@e6740000 {
+			compatible = "renesas,ipmmu-r8a77995";
+			reg = <0 0xe6740000 0 0x1000>;
+			renesas,ipmmu-main = <&ipmmu_mm 0>;
+			#iommu-cells = <1>;
+			status = "disabled";
+		};
+
+		ipmmu_ds1: mmu@e7740000 {
+			compatible = "renesas,ipmmu-r8a77995";
+			reg = <0 0xe7740000 0 0x1000>;
+			renesas,ipmmu-main = <&ipmmu_mm 1>;
+			#iommu-cells = <1>;
+			status = "disabled";
+		};
+
+		ipmmu_mm: mmu@e67b0000 {
+			compatible = "renesas,ipmmu-r8a77995";
+			reg = <0 0xe67b0000 0 0x1000>;
+			interrupts = <GIC_SPI 196 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 197 IRQ_TYPE_LEVEL_HIGH>;
+			#iommu-cells = <1>;
+			status = "disabled";
+		};
+
+
 		cpg: clock-controller@e6150000 {
 			compatible = "renesas,r8a77995-cpg-mssr";
 			reg = <0 0xe6150000 0 0x1000>;
@@ -155,6 +244,78 @@
 			resets = <&cpg 407>;
 		};
 
+		dmac0: dma-controller@e6700000 {
+			compatible = "renesas,dmac-r8a77995",
+				     "renesas,rcar-dmac";
+			reg = <0 0xe6700000 0 0x10000>;
+			interrupts = <GIC_SPI 199 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 200 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 201 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 202 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 203 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 204 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 205 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 206 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 207 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "error",
+					"ch0", "ch1", "ch2", "ch3",
+					"ch4", "ch5", "ch6", "ch7";
+			clocks = <&cpg CPG_MOD 219>;
+			clock-names = "fck";
+			power-domains = <&sysc R8A77995_PD_ALWAYS_ON>;
+			resets = <&cpg 219>;
+			#dma-cells = <1>;
+			dma-channels = <8>;
+		};
+
+		dmac1: dma-controller@e7300000 {
+			compatible = "renesas,dmac-r8a77995",
+				     "renesas,rcar-dmac";
+			reg = <0 0xe7300000 0 0x10000>;
+			interrupts = <GIC_SPI 220 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 216 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 217 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 218 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 219 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 308 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 309 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 310 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 311 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "error",
+					"ch0", "ch1", "ch2", "ch3",
+					"ch4", "ch5", "ch6", "ch7";
+			clocks = <&cpg CPG_MOD 218>;
+			clock-names = "fck";
+			power-domains = <&sysc R8A77995_PD_ALWAYS_ON>;
+			resets = <&cpg 218>;
+			#dma-cells = <1>;
+			dma-channels = <8>;
+		};
+
+		dmac2: dma-controller@e7310000 {
+			compatible = "renesas,dmac-r8a77995",
+				     "renesas,rcar-dmac";
+			reg = <0 0xe7310000 0 0x10000>;
+			interrupts = <GIC_SPI 416 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 417 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 418 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 419 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 420 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 421 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 422 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 423 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 424 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "error",
+					"ch0", "ch1", "ch2", "ch3",
+					"ch4", "ch5", "ch6", "ch7";
+			clocks = <&cpg CPG_MOD 217>;
+			clock-names = "fck";
+			power-domains = <&sysc R8A77995_PD_ALWAYS_ON>;
+			resets = <&cpg 217>;
+			#dma-cells = <1>;
+			dma-channels = <8>;
+		};
+
 		gpio0: gpio@e6050000 {
 			compatible = "renesas,gpio-r8a77995",
 				     "renesas,rcar-gen3-gpio",
@@ -267,6 +428,63 @@
 			resets = <&cpg 906>;
 		};
 
+		can0: can@e6c30000 {
+			compatible = "renesas,can-r8a77995",
+				     "renesas,rcar-gen3-can";
+			reg = <0 0xe6c30000 0 0x1000>;
+			interrupts = <GIC_SPI 186 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 916>,
+			       <&cpg CPG_CORE R8A77995_CLK_CANFD>,
+			       <&can_clk>;
+			clock-names = "clkp1", "clkp2", "can_clk";
+			assigned-clocks = <&cpg CPG_CORE R8A77995_CLK_CANFD>;
+			assigned-clock-rates = <40000000>;
+			power-domains = <&sysc R8A77995_PD_ALWAYS_ON>;
+			resets = <&cpg 916>;
+			status = "disabled";
+		};
+
+		can1: can@e6c38000 {
+			compatible = "renesas,can-r8a77995",
+				     "renesas,rcar-gen3-can";
+			reg = <0 0xe6c38000 0 0x1000>;
+			interrupts = <GIC_SPI 187 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 915>,
+			       <&cpg CPG_CORE R8A77995_CLK_CANFD>,
+			       <&can_clk>;
+			clock-names = "clkp1", "clkp2", "can_clk";
+			assigned-clocks = <&cpg CPG_CORE R8A77995_CLK_CANFD>;
+			assigned-clock-rates = <40000000>;
+			power-domains = <&sysc R8A77995_PD_ALWAYS_ON>;
+			resets = <&cpg 915>;
+			status = "disabled";
+		};
+
+		canfd: can@e66c0000 {
+			compatible = "renesas,r8a77995-canfd",
+				     "renesas,rcar-gen3-canfd";
+			reg = <0 0xe66c0000 0 0x8000>;
+			interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>,
+				   <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 914>,
+			       <&cpg CPG_CORE R8A77995_CLK_CANFD>,
+			       <&can_clk>;
+			clock-names = "fck", "canfd", "can_clk";
+			assigned-clocks = <&cpg CPG_CORE R8A77995_CLK_CANFD>;
+			assigned-clock-rates = <40000000>;
+			power-domains = <&sysc R8A77995_PD_ALWAYS_ON>;
+			resets = <&cpg 914>;
+			status = "disabled";
+
+			channel0 {
+				status = "disabled";
+			};
+
+			channel1 {
+				status = "disabled";
+			};
+		};
+
 		avb: ethernet@e6800000 {
 			compatible = "renesas,etheravb-r8a77995",
 				     "renesas,etheravb-rcar-gen3";
@@ -307,6 +525,7 @@
 			power-domains = <&sysc R8A77995_PD_ALWAYS_ON>;
 			resets = <&cpg 812>;
 			phy-mode = "rgmii-txid";
+			iommus = <&ipmmu_ds0 16>;
 			#address-cells = <1>;
 			#size-cells = <0>;
 			status = "disabled";
@@ -321,6 +540,9 @@
 				 <&cpg CPG_CORE R8A77995_CLK_S3D1C>,
 				 <&scif_clk>;
 			clock-names = "fck", "brg_int", "scif_clk";
+			dmas = <&dmac1 0x13>, <&dmac1 0x12>,
+			       <&dmac2 0x13>, <&dmac2 0x12>;
+			dma-names = "tx", "rx", "tx", "rx";
 			power-domains = <&sysc R8A77995_PD_ALWAYS_ON>;
 			resets = <&cpg 310>;
 			status = "disabled";
@@ -366,6 +588,18 @@
 			status = "disabled";
 		};
 
+		sdhi2: sd@ee140000 {
+			compatible = "renesas,sdhi-r8a77995",
+				     "renesas,rcar-gen3-sdhi";
+			reg = <0 0xee140000 0 0x2000>;
+			interrupts = <GIC_SPI 167 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 312>;
+			max-frequency = <200000000>;
+			power-domains = <&sysc R8A77995_PD_ALWAYS_ON>;
+			resets = <&cpg 312>;
+			status = "disabled";
+		};
+
 		ehci0: usb@ee080100 {
 			compatible = "generic-ehci";
 			reg = <0 0xee080100 0 0x100>;

arch/arm64/boot/dts/renesas/salvator-common.dtsi

@@ -263,6 +263,7 @@
 		reg = <0>;
 		interrupt-parent = <&gpio2>;
 		interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+		reset-gpios = <&gpio2 10 GPIO_ACTIVE_LOW>;
 	};
 };
 
@@ -354,6 +355,30 @@
 
 &i2c_dvfs {
 	status = "okay";
+
+	pmic: pmic@30 {
+		pinctrl-0 = <&irq0_pins>;
+		pinctrl-names = "default";
+
+		compatible = "rohm,bd9571mwv";
+		reg = <0x30>;
+		interrupt-parent = <&intc_ex>;
+		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		regulators {
+			dvfs: dvfs {
+				regulator-name = "dvfs";
+				regulator-min-microvolt = <750000>;
+				regulator-max-microvolt = <1030000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+		};
+	};
 };
 
 &ohci0 {
@@ -409,6 +434,11 @@
 		function = "i2c2";
 	};
 
+	irq0_pins: irq0 {
+		groups = "intc_ex_irq0";
+		function = "intc_ex";
+	};
+
 	pwm1_pins: pwm1 {
 		groups = "pwm1_a";
 		function = "pwm1";
@@ -595,6 +625,7 @@
 	bus-width = <8>;
 	mmc-hs200-1_8v;
 	non-removable;
+	fixed-emmc-driver-type = <1>;
 	status = "okay";
 };
 
@@ -616,6 +647,10 @@
 	shared-pin;
 };
 
+&usb_extal_clk {
+	clock-frequency = <50000000>;
+};
+
 &usb2_phy0 {
 	pinctrl-0 = <&usb0_pins>;
 	pinctrl-names = "default";
@@ -631,6 +666,21 @@
 	status = "okay";
 };
 
+&usb3_peri0 {
+	phys = <&usb3_phy0>;
+	phy-names = "usb";
+
+	status = "okay";
+};
+
+&usb3_phy0 {
+	status = "okay";
+};
+
+&usb3s0_clk {
+	clock-frequency = <100000000>;
+};
+
 &wdt0 {
 	timeout-sec = <60>;
 	status = "okay";

arch/arm64/boot/dts/renesas/ulcb-kf.dtsi

@@ -29,6 +29,7 @@
 };
 
 &ehci0 {
+	dr_mode = "otg";
 	status = "okay";
 };
 
@@ -41,6 +42,7 @@
 };
 
 &hsusb {
+	dr_mode = "otg";
 	status = "okay";
 };
 
@@ -67,6 +69,20 @@
 			output-high;
 			line-name = "HUB rst";
 		};
+
+		otg_offvbusn {
+			gpio-hog;
+			gpios = <8 GPIO_ACTIVE_HIGH>;
+			output-low;
+			line-name = "OTG OFFVBUSn";
+		};
+
+		otg_extlpn {
+			gpio-hog;
+			gpios = <9 GPIO_ACTIVE_HIGH>;
+			output-high;
+			line-name = "OTG EXTLPn";
+		};
 	};
 
 	gpio_exp_75: gpio@75 {
@@ -119,6 +135,7 @@
 };
 
 &ohci0 {
+	dr_mode = "otg";
 	status = "okay";
 };
 
@@ -154,6 +171,11 @@
 		groups = "scif1_data_b", "scif1_ctrl";
 		function = "scif1";
 	};
+
+	usb0_pins: usb0 {
+		groups = "usb0";
+		function = "usb0";
+	};
 };
 
 &scif1 {
@@ -164,6 +186,13 @@
 	status = "okay";
 };
 
+&usb2_phy0 {
+	pinctrl-0 = <&usb0_pins>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
+
 &xhci0 {
 	status = "okay";
 };

arch/arm64/boot/dts/renesas/ulcb.dtsi

@@ -153,6 +153,7 @@
 		reg = <0>;
 		interrupt-parent = <&gpio2>;
 		interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+		reset-gpios = <&gpio2 10 GPIO_ACTIVE_LOW>;
 	};
 };
 

arch/arm64/boot/dts/rockchip/rk3328.dtsi

@@ -531,6 +531,31 @@
 		status = "disabled";
 	};
 
+	efuse: efuse@ff260000 {
+		compatible = "rockchip,rk3328-efuse";
+		reg = <0x0 0xff260000 0x0 0x50>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		clocks = <&cru SCLK_EFUSE>;
+		clock-names = "pclk_efuse";
+		rockchip,efuse-size = <0x20>;
+
+		/* Data cells */
+		efuse_id: id@7 {
+			reg = <0x07 0x10>;
+		};
+		cpu_leakage: cpu-leakage@17 {
+			reg = <0x17 0x1>;
+		};
+		logic_leakage: logic-leakage@19 {
+			reg = <0x19 0x1>;
+		};
+		efuse_cpu_version: cpu-version@1a {
+			reg = <0x1a 0x1>;
+			bits = <3 3>;
+		};
+	};
+
 	saradc: adc@ff280000 {
 		compatible = "rockchip,rk3328-saradc", "rockchip,rk3399-saradc";
 		reg = <0x0 0xff280000 0x0 0x100>;
@@ -543,6 +568,28 @@
 		status = "disabled";
 	};
 
+	gpu: gpu@ff300000 {
+		compatible = "rockchip,rk3328-mali", "arm,mali-450";
+		reg = <0x0 0xff300000 0x0 0x40000>;
+		interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "gp",
+				  "gpmmu",
+				  "pp",
+				  "pp0",
+				  "ppmmu0",
+				  "pp1",
+				  "ppmmu1";
+		clocks = <&cru ACLK_GPU>, <&cru ACLK_GPU>;
+		clock-names = "bus", "core";
+		resets = <&cru SRST_GPU_A>;
+	};
+
 	h265e_mmu: iommu@ff330200 {
 		compatible = "rockchip,iommu";
 		reg = <0x0 0xff330200 0 0x100>;

arch/arm64/boot/dts/rockchip/rk3399-gru-kevin.dts

@@ -93,6 +93,18 @@
 		pwm-delay-us = <10000>;
 	};
 
+	edp_panel: edp-panel {
+		compatible = "sharp,lq123p1jx31", "simple-panel";
+		backlight = <&backlight>;
+		power-supply = <&pp3300_disp>;
+
+		ports {
+			panel_in_edp: endpoint {
+				remote-endpoint = <&edp_out_panel>;
+			};
+		};
+	};
+
 	thermistor_ppvar_bigcpu: thermistor-ppvar-bigcpu {
 		compatible = "murata,ncp15wb473";
 		pullup-uv = <1800000>;
@@ -268,6 +280,23 @@ ap_i2c_dig: &i2c2 {
 	};
 };
 
+&edp {
+	status = "okay";
+
+	ports {
+		edp_out: port@1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			edp_out_panel: endpoint@0 {
+				reg = <0>;
+				remote-endpoint = <&panel_in_edp>;
+			};
+		};
+	};
+};
+
 &ppvar_bigcpu_pwm {
 	regulator-min-microvolt = <798674>;
 	regulator-max-microvolt = <1302172>;

arch/arm64/boot/dts/rockchip/rk3399-gru.dtsi

@@ -855,6 +855,20 @@ ap_i2c_audio: &i2c8 {
 			compatible = "google,cros-ec-pwm";
 			#pwm-cells = <1>;
 		};
+
+		usbc_extcon0: extcon@0 {
+			compatible = "google,extcon-usbc-cros-ec";
+			google,usb-port-id = <0>;
+
+			#extcon-cells = <0>;
+		};
+
+		usbc_extcon1: extcon@1 {
+			compatible = "google,extcon-usbc-cros-ec";
+			google,usb-port-id = <1>;
+
+			#extcon-cells = <0>;
+		};
 	};
 };
 
@@ -865,6 +879,16 @@ ap_i2c_audio: &i2c8 {
 	rockchip,hw-tshut-polarity = <1>; /* tshut polarity 0:LOW 1:HIGH */
 };
 
+&tcphy0 {
+	status = "okay";
+	extcon = <&usbc_extcon0>;
+};
+
+&tcphy1 {
+	status = "okay";
+	extcon = <&usbc_extcon1>;
+};
+
 &u2phy0 {
 	status = "okay";
 };
@@ -911,6 +935,7 @@ ap_i2c_audio: &i2c8 {
 
 &usbdrd3_0 {
 	status = "okay";
+	extcon = <&usbc_extcon0>;
 };
 
 &usbdrd_dwc3_0 {
@@ -920,6 +945,7 @@ ap_i2c_audio: &i2c8 {
 
 &usbdrd3_1 {
 	status = "okay";
+	extcon = <&usbc_extcon1>;
 };
 
 &usbdrd_dwc3_1 {
@@ -927,6 +953,22 @@ ap_i2c_audio: &i2c8 {
 	dr_mode = "host";
 };
 
+&vopb {
+	status = "okay";
+};
+
+&vopb_mmu {
+	status = "okay";
+};
+
+&vopl {
+	status = "okay";
+};
+
+&vopl_mmu {
+	status = "okay";
+};
+
 #include <arm/cros-ec-keyboard.dtsi>
 #include <arm/cros-ec-sbs.dtsi>
 

arch/arm64/boot/dts/rockchip/rk3399.dtsi

@@ -397,9 +397,13 @@
 		#size-cells = <2>;
 		ranges;
 		clocks = <&cru SCLK_USB3OTG0_REF>, <&cru SCLK_USB3OTG0_SUSPEND>,
-			 <&cru ACLK_USB3OTG0>, <&cru ACLK_USB3_GRF>;
+			 <&cru ACLK_USB3OTG0>, <&cru ACLK_USB3_RKSOC_AXI_PERF>,
+			 <&cru ACLK_USB3>, <&cru ACLK_USB3_GRF>;
 		clock-names = "ref_clk", "suspend_clk",
-			      "bus_clk", "grf_clk";
+			      "bus_clk", "aclk_usb3_rksoc_axi_perf",
+			      "aclk_usb3", "grf_clk";
+		resets = <&cru SRST_A_USB3_OTG0>;
+		reset-names = "usb3-otg";
 		status = "disabled";
 
 		usbdrd_dwc3_0: dwc3 {
@@ -407,14 +411,15 @@
 			reg = <0x0 0xfe800000 0x0 0x100000>;
 			interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH 0>;
 			dr_mode = "otg";
-			phys = <&u2phy0_otg>;
-			phy-names = "usb2-phy";
+			phys = <&u2phy0_otg>, <&tcphy0_usb3>;
+			phy-names = "usb2-phy", "usb3-phy";
 			phy_type = "utmi_wide";
 			snps,dis_enblslpm_quirk;
 			snps,dis-u2-freeclk-exists-quirk;
 			snps,dis_u2_susphy_quirk;
 			snps,dis-del-phy-power-chg-quirk;
 			snps,dis-tx-ipgap-linecheck-quirk;
+			power-domains = <&power RK3399_PD_USB3>;
 			status = "disabled";
 		};
 	};
@@ -425,9 +430,13 @@
 		#size-cells = <2>;
 		ranges;
 		clocks = <&cru SCLK_USB3OTG1_REF>, <&cru SCLK_USB3OTG1_SUSPEND>,
-			 <&cru ACLK_USB3OTG1>, <&cru ACLK_USB3_GRF>;
+			 <&cru ACLK_USB3OTG1>, <&cru ACLK_USB3_RKSOC_AXI_PERF>,
+			 <&cru ACLK_USB3>, <&cru ACLK_USB3_GRF>;
 		clock-names = "ref_clk", "suspend_clk",
-			      "bus_clk", "grf_clk";
+			      "bus_clk", "aclk_usb3_rksoc_axi_perf",
+			      "aclk_usb3", "grf_clk";
+		resets = <&cru SRST_A_USB3_OTG1>;
+		reset-names = "usb3-otg";
 		status = "disabled";
 
 		usbdrd_dwc3_1: dwc3 {
@@ -435,14 +444,15 @@
 			reg = <0x0 0xfe900000 0x0 0x100000>;
 			interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH 0>;
 			dr_mode = "otg";
-			phys = <&u2phy1_otg>;
-			phy-names = "usb2-phy";
+			phys = <&u2phy1_otg>, <&tcphy1_usb3>;
+			phy-names = "usb2-phy", "usb3-phy";
 			phy_type = "utmi_wide";
 			snps,dis_enblslpm_quirk;
 			snps,dis-u2-freeclk-exists-quirk;
 			snps,dis_u2_susphy_quirk;
 			snps,dis-del-phy-power-chg-quirk;
 			snps,dis-tx-ipgap-linecheck-quirk;
+			power-domains = <&power RK3399_PD_USB3>;
 			status = "disabled";
 		};
 	};
@@ -991,6 +1001,12 @@
 				clocks = <&cru HCLK_SDIO>;
 				pm_qos = <&qos_sdioaudio>;
 			};
+			pd_usb3@RK3399_PD_USB3 {
+				reg = <RK3399_PD_USB3>;
+				clocks = <&cru ACLK_USB3>;
+				pm_qos = <&qos_usb_otg0>,
+					 <&qos_usb_otg1>;
+			};
 			pd_vio@RK3399_PD_VIO {
 				reg = <RK3399_PD_VIO>;
 				#address-cells = <1>;
@@ -1526,6 +1542,11 @@
 				reg = <2>;
 				remote-endpoint = <&hdmi_in_vopl>;
 			};
+
+			vopl_out_mipi1: endpoint@3 {
+				reg = <3>;
+				remote-endpoint = <&mipi1_in_vopl>;
+			};
 		};
 	};
 
@@ -1573,6 +1594,11 @@
 				reg = <2>;
 				remote-endpoint = <&hdmi_in_vopb>;
 			};
+
+			vopb_out_mipi1: endpoint@3 {
+				reg = <3>;
+				remote-endpoint = <&mipi1_in_vopb>;
+			};
 		};
 	};
 
@@ -1648,11 +1674,17 @@
 			 <&cru SCLK_DPHY_TX0_CFG>, <&cru PCLK_VIO_GRF>;
 		clock-names = "ref", "pclk", "phy_cfg", "grf";
 		power-domains = <&power RK3399_PD_VIO>;
+		resets = <&cru SRST_P_MIPI_DSI0>;
+		reset-names = "apb";
 		rockchip,grf = <&grf>;
 		status = "disabled";
 
 		ports {
-			mipi_in: port {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			mipi_in: port@0 {
+				reg = <0>;
 				#address-cells = <1>;
 				#size-cells = <0>;
 
@@ -1668,6 +1700,41 @@
 		};
 	};
 
+	mipi_dsi1: mipi@ff968000 {
+		compatible = "rockchip,rk3399-mipi-dsi", "snps,dw-mipi-dsi";
+		reg = <0x0 0xff968000 0x0 0x8000>;
+		interrupts = <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH 0>;
+		clocks = <&cru SCLK_DPHY_PLL>, <&cru PCLK_MIPI_DSI1>,
+			 <&cru SCLK_DPHY_TX1RX1_CFG>, <&cru PCLK_VIO_GRF>;
+		clock-names = "ref", "pclk", "phy_cfg", "grf";
+		power-domains = <&power RK3399_PD_VIO>;
+		resets = <&cru SRST_P_MIPI_DSI1>;
+		reset-names = "apb";
+		rockchip,grf = <&grf>;
+		status = "disabled";
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			mipi1_in: port@0 {
+				reg = <0>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				mipi1_in_vopb: endpoint@0 {
+					reg = <0>;
+					remote-endpoint = <&vopb_out_mipi1>;
+				};
+
+				mipi1_in_vopl: endpoint@1 {
+					reg = <1>;
+					remote-endpoint = <&vopl_out_mipi1>;
+				};
+			};
+		};
+	};
+
 	edp: edp@ff970000 {
 		compatible = "rockchip,rk3399-edp";
 		reg = <0x0 0xff970000 0x0 0x8000>;

arch/arm64/boot/dts/socionext/uniphier-ld11-ref.dts

@@ -50,7 +50,7 @@
 &gpio {
 	xirq0 {
 		gpio-hog;
-		gpios = <120 0>;
+		gpios = <UNIPHIER_GPIO_IRQ(0) 0>;
 		input;
 	};
 };