remove the mg_disk driver

This drivers was added in 2008, but as far as a I can tell we never had a
single platform that actually registered resources for the platform driver.

It's also been unmaintained for a long time and apparently has a ATA mode
that can be driven using the IDE/libata subsystem.

Signed-off-by: Christoph Hellwig <[email protected]>
Reviewed-by: Hannes Reinecke <[email protected]>
Signed-off-by: Jens Axboe <[email protected]>

Documentation/blockdev/mflash.txt

@@ -1,84 +0,0 @@
-This document describes m[g]flash support in linux.
-
-Contents
-  1. Overview
-  2. Reserved area configuration
-  3. Example of mflash platform driver registration
-
-1. Overview
-
-Mflash and gflash are embedded flash drive. The only difference is mflash is
-MCP(Multi Chip Package) device. These two device operate exactly same way.
-So the rest mflash repersents mflash and gflash altogether.
-
-Internally, mflash has nand flash and other hardware logics and supports
-2 different operation (ATA, IO) modes. ATA mode doesn't need any new
-driver and currently works well under standard IDE subsystem. Actually it's
-one chip SSD. IO mode is ATA-like custom mode for the host that doesn't have
-IDE interface.
-
-Following are brief descriptions about IO mode.
-A. IO mode based on ATA protocol and uses some custom command. (read confirm,
-write confirm)
-B. IO mode uses SRAM bus interface.
-C. IO mode supports 4kB boot area, so host can boot from mflash.
-
-2. Reserved area configuration
-If host boot from mflash, usually needs raw area for boot loader image. All of
-the mflash's block device operation will be taken this value as start offset.
-Note that boot loader's size of reserved area and kernel configuration value
-must be same.
-
-3. Example of mflash platform driver registration
-Working mflash is very straight forward. Adding platform device stuff to board
-configuration file is all. Here is some pseudo example.
-
-static struct mg_drv_data mflash_drv_data = {
-	/* If you want to polling driver set to 1 */
-	.use_polling = 0,
-	/* device attribution */
-	.dev_attr = MG_BOOT_DEV
-};
-
-static struct resource mg_mflash_rsc[] = {
-	/* Base address of mflash */
-	[0] = {
-		.start = 0x08000000,
-		.end = 0x08000000 + SZ_64K - 1,
-		.flags = IORESOURCE_MEM
-	},
-	/* mflash interrupt pin */
-	[1] = {
-		.start = IRQ_GPIO(84),
-		.end = IRQ_GPIO(84),
-		.flags = IORESOURCE_IRQ
-	},
-	/* mflash reset pin */
-	[2] = {
-		.start = 43,
-		.end = 43,
-		.name = MG_RST_PIN,
-		.flags = IORESOURCE_IO
-	},
-	/* mflash reset-out pin
-	 * If you use mflash as storage device (i.e. other than MG_BOOT_DEV),
-	 * should assign this */
-	[3] = {
-		.start = 51,
-		.end = 51,
-		.name = MG_RSTOUT_PIN,
-		.flags = IORESOURCE_IO
-	}
-};
-
-static struct platform_device mflash_dev = {
-	.name = MG_DEV_NAME,
-	.id = -1,
-	.dev = {
-		.platform_data = &mflash_drv_data,
-	},
-	.num_resources = ARRAY_SIZE(mg_mflash_rsc),
-	.resource = mg_mflash_rsc
-};
-
-platform_device_register(&mflash_dev);