diff --git a/qcom/pm8150.dtsi b/qcom/pm8150.dtsi new file mode 100644 index 000000000000..21683a4ecffb --- /dev/null +++ b/qcom/pm8150.dtsi @@ -0,0 +1,164 @@ +#include +#include +#include +#include +#include + +&spmi_bus { + #address-cells = <2>; + #size-cells = <0>; + interrupt-controller; + #interrupt-cells = <4>; + + qcom,pm8150@0 { + compatible = "qcom,spmi-pmic"; + reg = <0 SPMI_USID>; + #address-cells = <1>; + #size-cells = <0>; + + pm8150_tz: qcom,temp-alarm@2400 { + compatible = "qcom,spmi-temp-alarm"; + reg = <0x2400>; + interrupts = <0x0 0x24 0x0 IRQ_TYPE_EDGE_BOTH>; + io-channels = <&pm8150_vadc ADC5_DIE_TEMP>; + io-channel-names = "thermal"; + #thermal-sensor-cells = <0>; + }; + + qcom,power-on@800 { + compatible = "qcom,qpnp-power-on"; + reg = <0x800 0x100>; + interrupts = <0x0 0x8 0x0 IRQ_TYPE_NONE>, + <0x0 0x8 0x1 IRQ_TYPE_NONE>; + interrupt-names = "kpdpwr", "resin"; + qcom,pon-dbc-delay = <15625>; + qcom,kpdpwr-sw-debounce; + qcom,system-reset; + qcom,store-hard-reset-reason; + + qcom,pon_1 { + qcom,pon-type = ; + qcom,pull-up; + linux,code = ; + }; + + qcom,pon_2 { + qcom,pon-type = ; + qcom,pull-up; + linux,code = ; + }; + }; + + pm8150_clkdiv: clock-controller@5b00 { + compatible = "qcom,spmi-clkdiv"; + reg = <0x5b00>; + #clock-cells = <1>; + qcom,num-clkdivs = <2>; + clock-output-names = "pm8150_div_clk1", + "pm8150_div_clk2"; + clocks = <&rpmhcc RPMH_CXO_CLK>; + clock-names = "xo"; + }; + + pm8150_rtc: qcom,pm8150_rtc { + compatible = "qcom,pm8941-rtc"; + reg = <0x6000>, <0x6100>; + reg-names = "rtc", "alarm"; + interrupts = <0x0 0x61 0x1 IRQ_TYPE_NONE>; + }; + + pm8150_gpios: pinctrl@c000 { + compatible = "qcom,pm8150-gpio"; + reg = <0xc000>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + pm8150_sdam_2: sdam@b100 { + compatible = "qcom,spmi-sdam"; + reg = <0xb100>; + }; + + pm8150_vadc: vadc@3100 { + compatible = "qcom,spmi-adc5"; + reg = <0x3100>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>; + interrupt-names = "eoc-int-en-set"; + #io-channel-cells = <1>; + io-channel-ranges; + + /* Channel node */ + ref_gnd { + reg = ; + label = "ref_gnd"; + qcom,pre-scaling = <1 1>; + }; + + vref_1p25 { + reg = ; + label = "vref_1p25"; + qcom,pre-scaling = <1 1>; + }; + + die_temp { + reg = ; + label = "die_temp"; + qcom,pre-scaling = <1 1>; + }; + }; + + pm8150_adc_tm: adc_tm@3500 { + compatible = "qcom,adc-tm5"; + reg = <0x3500>; + interrupts = <0x0 0x35 0x0 IRQ_TYPE_EDGE_RISING>; + interrupt-names = "thr-int-en"; + #address-cells = <1>; + #size-cells = <0>; + #thermal-sensor-cells = <1>; + io-channels = <&pm8150_vadc ADC5_XO_THERM_100K_PU>, + <&pm8150_vadc ADC5_AMUX_THM1_100K_PU>, + <&pm8150_vadc ADC5_AMUX_THM2_100K_PU>; + }; + }; + + qcom,pm8150@1 { + compatible ="qcom,spmi-pmic"; + reg = <1 SPMI_USID>; + #address-cells = <2>; + #size-cells = <0>; + }; +}; + +&thermal_zones { + pm8150_temp_alarm: pm8150_tz { + polling-delay-passive = <100>; + polling-delay = <0>; + thermal-governor = "step_wise"; + thermal-sensors = <&pm8150_tz>; + wake-capable-sensor; + + trips { + pm8150_trip0: trip0 { + temperature = <95000>; + hysteresis = <0>; + type = "passive"; + }; + + pm8150_trip1: trip1 { + temperature = <115000>; + hysteresis = <0>; + type = "passive"; + }; + + trip2 { + temperature = <145000>; + hysteresis = <0>; + type = "passive"; + }; + }; + }; +}; diff --git a/qcom/sa8155-adp-common.dtsi b/qcom/sa8155-adp-common.dtsi index fc99f15ac51c..b7e203419cc2 100644 --- a/qcom/sa8155-adp-common.dtsi +++ b/qcom/sa8155-adp-common.dtsi @@ -1,6 +1,8 @@ #include #include +#include "sa8155-pmic-overlay.dtsi" + &ufsphy_mem { compatible = "qcom,ufs-phy-qmp-v4"; diff --git a/qcom/sa8155-pmic-overlay.dtsi b/qcom/sa8155-pmic-overlay.dtsi new file mode 100644 index 000000000000..4c4fd12fe728 --- /dev/null +++ b/qcom/sa8155-pmic-overlay.dtsi @@ -0,0 +1,169 @@ + +#include "pm8150.dtsi" + +pm8150_1_tz: &pm8150_tz { +}; + +pm8150_1_clkdiv: &pm8150_clkdiv { + clock-output-names = "pm8150_1_div_clk1", "pm8150_1_div_clk2"; +}; + +pm8150_1_rtc: &pm8150_rtc { +}; + +pm8150_1_gpios: &pm8150_gpios { +}; + +/* PM8150_2: */ +&spmi_bus { + #address-cells = <2>; + #size-cells = <0>; + interrupt-controller; + #interrupt-cells = <4>; + + qcom,pm8150@4 { + compatible = "qcom,spmi-pmic"; + reg = <4 SPMI_USID>; + #address-cells = <1>; + #size-cells = <0>; + + pm8150_2_tz: qcom,temp-alarm@2400 { + compatible = "qcom,spmi-temp-alarm"; + reg = <0x2400>; + interrupts = <0x4 0x24 0x0 IRQ_TYPE_EDGE_RISING>; + io-channels = <&pm8150_2_vadc ADC5_DIE_TEMP>; + io-channel-names = "thermal"; + #thermal-sensor-cells = <0>; + qcom,temperature-threshold-set = <1>; + }; + + qcom,power-on@800 { + compatible = "qcom,qpnp-power-on"; + reg = <0x800>; + }; + + pm8150_2_clkdiv: clock-controller@5b00 { + compatible = "qcom,spmi-clkdiv"; + reg = <0x5b00>; + #clock-cells = <1>; + qcom,num-clkdivs = <2>; + clock-output-names = "pm8150_2_div_clk1", + "pm8150_2_div_clk2"; + clocks = <&rpmhcc RPMH_CXO_CLK>; + clock-names = "xo"; + }; + + pm8150_2_gpios: pinctrl@c000 { + compatible = "qcom,pm8150-gpio"; + reg = <0xc000>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + pm8150_2_vadc: vadc@3100 { + compatible = "qcom,spmi-adc5"; + reg = <0x3100>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <0x4 0x31 0x0 IRQ_TYPE_EDGE_RISING>; + interrupt-names = "eoc-int-en-set"; + #io-channel-cells = <1>; + io-channel-ranges; + + /* Channel node */ + ref_gnd { + reg = ; + label = "ref_gnd"; + qcom,pre-scaling = <1 1>; + }; + + vref_1p25 { + reg = ; + label = "vref_1p25"; + qcom,pre-scaling = <1 1>; + }; + + die_temp { + reg = ; + label = "die_temp"; + qcom,pre-scaling = <1 1>; + }; + }; + }; + + qcom,pm8150@5 { + compatible ="qcom,spmi-pmic"; + reg = <5 SPMI_USID>; + #address-cells = <1>; + #size-cells = <1>; + }; +}; + +/* PMIC GPIO pin control configurations: */ +&pm8150_1_gpios { + key_home { + key_home_default: key_home_default { + pins = "gpio1"; + function = "normal"; + input-enable; + bias-pull-up; + power-source = <0>; + }; + }; + + storage_sd_detect { + storage_cd_default: storage_cd_default { + pins = "gpio4"; + function = "normal"; + input-enable; + bias-pull-up; + power-source = <0>; + }; + }; + + key_vol_up { + key_vol_up_default: key_vol_up_default { + pins = "gpio6"; + function = "normal"; + input-enable; + bias-pull-up; + power-source = <1>; + }; + }; +}; + +#include + +&thermal_zones { + pm8150_2_temp_alarm: pm8150_2_tz { + polling-delay-passive = <100>; + polling-delay = <0>; + thermal-governor = "step_wise"; + thermal-sensors = <&pm8150_2_tz>; + wake-capable-sensor; + + trips { + pm8150_2_trip0: trip0 { + temperature = <95000>; + hysteresis = <0>; + type = "passive"; + }; + + pm8150_2_trip1: trip1 { + temperature = <115000>; + hysteresis = <0>; + type = "passive"; + }; + + trip2 { + temperature = <145000>; + hysteresis = <0>; + type = "passive"; + }; + }; + + }; + +}; diff --git a/qcom/sm8150.dtsi b/qcom/sm8150.dtsi index 961e4e0fb6e2..b8e9208d6ec6 100644 --- a/qcom/sm8150.dtsi +++ b/qcom/sm8150.dtsi @@ -13,6 +13,8 @@ #include #include #include +#include +#include / { model = "Qualcomm Technologies, Inc. SM8150"; @@ -871,6 +873,88 @@ #freq-domain-cells = <2>; }; + spmi_bus: qcom,spmi@c440000 { + compatible = "qcom,spmi-pmic-arb"; + reg = <0xc440000 0x1100>, + <0xc600000 0x2000000>, + <0xe600000 0x100000>, + <0xe700000 0xa0000>, + <0xc40a000 0x26000>; + reg-names = "core", "chnls", "obsrvr", "intr", "cnfg"; + interrupts-extended = <&pdc 1 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "periph_irq"; + interrupt-controller; + #interrupt-cells = <4>; + #address-cells = <2>; + #size-cells = <0>; + cell-index = <0>; + qcom,channel = <0>; + qcom,ee = <0>; + }; + + spmi_debug_bus: qcom,spmi-debug@6b22000 { + compatible = "qcom,spmi-pmic-arb-debug"; + reg = <0x6b22000 0x60>, <0x7820a8 0x4>; + reg-names = "core", "fuse"; + clocks = <&aopcc QDSS_CLK>; + clock-names = "core_clk"; + qcom,fuse-disable-bit = <24>; + #address-cells = <2>; + #size-cells = <0>; + status = "disabled"; + + qcom,pm8150-debug@0 { + compatible = "qcom,spmi-pmic"; + reg = <0 SPMI_USID>; + #address-cells = <2>; + #size-cells = <0>; + qcom,can-sleep; + }; + + qcom,pm8150-debug@1 { + compatible = "qcom,spmi-pmic"; + reg = <1 SPMI_USID>; + #address-cells = <2>; + #size-cells = <0>; + qcom,can-sleep; + }; + + qcom,pm8150b-debug@2 { + compatible = "qcom,spmi-pmic"; + reg = <2 SPMI_USID>; + #address-cells = <2>; + #size-cells = <0>; + qcom,can-sleep; + }; + + qcom,pm8150b-debug@3 { + compatible = "qcom,spmi-pmic"; + reg = <3 SPMI_USID>; + #address-cells = <2>; + #size-cells = <0>; + qcom,can-sleep; + }; + + qcom,pm8150l-debug@4 { + compatible = "qcom,spmi-pmic"; + reg = <4 SPMI_USID>; + #address-cells = <2>; + #size-cells = <0>; + qcom,can-sleep; + }; + + qcom,pm8150l-debug@5 { + compatible = "qcom,spmi-pmic"; + reg = <5 SPMI_USID>; + #address-cells = <2>; + #size-cells = <0>; + qcom,can-sleep; + }; + }; + + thermal_zones: thermal-zones { + }; + osm_l3: interconnect@0x18321000 { reg = <0x18321000 0x1400>; compatible = "qcom,sm8150-osm-l3";