Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus

Pull MIPS updates from Ralf Baechle:
 "This is the main pull request for MIPS for Linux 4.1.  Most
  noteworthy:

   - Add more Octeon-optimized crypto functions
   - Octeon crypto preemption and locking fixes
   - Little endian support for Octeon
   - Use correct CSR to soft reset Octeons
   - Support LEDs on the Octeon-based DSR-1000N
   - Fix PCI interrupt mapping for the Octeon-based DSR-1000N
   - Mark prom_free_prom_memory() as __init for a number of systems
   - Support for Imagination's Pistachio SOC.  This includes arch and
     CLK bits.  I'd like to merge pinctrl bits later
   - Improve parallelism of csum_partial for certain pipelines
   - Organize DTB files in subdirs like other architectures
   - Implement read_sched_clock for all MIPS platforms other than
     Octeon
   - Massive series of 38 fixes and cleanups for the FPU emulator /
     kernel
   - Further FPU remulator work to support new features.  This sits on a
     separate branch which also has been pulled into the 4.1 KVM branch
   - Clean up and fixes for the SEAD3 eval board; remove unused file
   - Various updates for Netlogic platforms
   - A number of small updates for Loongson 3 platforms
   - Increase the memory limit for ATH79 platforms to 256MB
   - A fair number of fixes and updates for BCM47xx platforms
   - Finish the implementation of XPA support
   - MIPS FDC support.  No, not floppy controller but Fast Debug Channel :)
   - Detect the R16000 used in SGI legacy platforms
   - Fix Kconfig dependencies for the SSB bus support"

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (265 commits)
  MIPS: Makefile: Fix MIPS ASE detection code
  MIPS: asm: elf: Set O32 default FPU flags
  MIPS: BCM47XX: Fix detecting Microsoft MN-700 & Asus WL500G
  MIPS: Kconfig: Disable SMP/CPS for 64-bit
  MIPS: Hibernate: flush TLB entries earlier
  MIPS: smp-cps: cpu_set FPU mask if FPU present
  MIPS: lose_fpu(): Disable FPU when MSA enabled
  MIPS: ralink: add missing symbol for RALINK_ILL_ACC
  MIPS: ralink: Fix bad config symbol in PCI makefile.
  SSB: fix Kconfig dependencies
  MIPS: Malta: Detect and fix bad memsize values
  Revert "MIPS: Avoid pipeline stalls on some MIPS32R2 cores."
  MIPS: Octeon: Delete override of cpu_has_mips_r2_exec_hazard.
  MIPS: Fix cpu_has_mips_r2_exec_hazard.
  MIPS: kernel: entry.S: Set correct ISA level for mips_ihb
  MIPS: asm: spinlock: Fix addiu instruction for R10000_LLSC_WAR case
  MIPS: r4kcache: Use correct base register for MIPS R6 cache flushes
  MIPS: Kconfig: Fix typo for the r2-to-r6 emulator kernel parameter
  MIPS: unaligned: Fix regular load/store instruction emulation for EVA
  MIPS: unaligned: Surround load/store macros in do {} while statements
  ...

drivers/tty/Kconfig

@@ -419,4 +419,51 @@ config DA_CONSOLE
 	help
 	  This enables a console on a Dash channel.
 
+config MIPS_EJTAG_FDC_TTY
+	bool "MIPS EJTAG Fast Debug Channel TTY"
+	depends on MIPS_CDMM
+	help
+	  This enables a TTY and console on the MIPS EJTAG Fast Debug Channels,
+	  if they are present. This can be useful when working with an EJTAG
+	  probe which supports it, to get console output and a login prompt via
+	  EJTAG without needing to connect a serial cable.
+
+	  TTY devices are named e.g. ttyFDC3c2 (for FDC channel 2 of the FDC on
+	  CPU3).
+
+	  The console can be enabled with console=fdc1 (for FDC channel 1 on all
+	  CPUs). Do not use the console unless there is a debug probe attached
+	  to drain the FDC TX FIFO.
+
+	  If unsure, say N.
+
+config MIPS_EJTAG_FDC_EARLYCON
+	bool "Early FDC console"
+	depends on MIPS_EJTAG_FDC_TTY
+	help
+	  This registers a console on FDC channel 1 very early during boot (from
+	  MIPS arch code). This is useful for bring-up and debugging early boot
+	  issues.
+
+	  Do not enable unless there is a debug probe attached to drain the FDC
+	  TX FIFO.
+
+	  If unsure, say N.
+
+config MIPS_EJTAG_FDC_KGDB
+	bool "Use KGDB over an FDC channel"
+	depends on MIPS_EJTAG_FDC_TTY && KGDB
+	default y
+	help
+          This enables the use of KGDB over an FDC channel, allowing KGDB to be
+          used remotely or when a serial port isn't available.
+
+config MIPS_EJTAG_FDC_KGDB_CHAN
+	int "KGDB FDC channel"
+	depends on MIPS_EJTAG_FDC_KGDB
+	range 2 15
+	default 3
+	help
+	  FDC channel number to use for KGDB.
+
 endif # TTY

drivers/tty/Makefile

@@ -29,5 +29,6 @@ obj-$(CONFIG_SYNCLINK)		+= synclink.o
 obj-$(CONFIG_PPC_EPAPR_HV_BYTECHAN) += ehv_bytechan.o
 obj-$(CONFIG_GOLDFISH_TTY)	+= goldfish.o
 obj-$(CONFIG_DA_TTY)		+= metag_da.o
+obj-$(CONFIG_MIPS_EJTAG_FDC_TTY) += mips_ejtag_fdc.o
 
 obj-y += ipwireless/