From 1ff4023aabffd4efbc4fa80fbed8b1e43c40ac55 Mon Sep 17 00:00:00 2001 From: Hans de Goede Date: Fri, 15 Jul 2016 08:54:19 +0200 Subject: [PATCH 01/31] ARM: dts: sun6i-a31s-colorfly-e708-q1: Add full otg support Now that we've all the necessary bits in place we can enable full otg support on these tablets. Signed-off-by: Hans de Goede Signed-off-by: Maxime Ripard --- .../boot/dts/sun6i-a31s-colorfly-e708-q1.dts | 32 ++++++++++++++----- 1 file changed, 24 insertions(+), 8 deletions(-) diff --git a/arch/arm/boot/dts/sun6i-a31s-colorfly-e708-q1.dts b/arch/arm/boot/dts/sun6i-a31s-colorfly-e708-q1.dts index e182eec6d878..9040bb9f80f3 100644 --- a/arch/arm/boot/dts/sun6i-a31s-colorfly-e708-q1.dts +++ b/arch/arm/boot/dts/sun6i-a31s-colorfly-e708-q1.dts @@ -106,6 +106,13 @@ allwinner,drive = ; allwinner,pull = ; }; + + usb0_id_detect_pin: usb0_id_detect_pin@0 { + allwinner,pins = "PA15"; + allwinner,function = "gpio_in"; + allwinner,drive = ; + allwinner,pull = ; + }; }; &p2wi { @@ -116,6 +123,8 @@ reg = <0x68>; interrupt-parent = <&nmi_intc>; interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + drivevbus-supply = <®_vcc5v0>; + x-powers,drive-vbus-en; }; }; @@ -185,24 +194,31 @@ regulator-name = "vcc-pg"; }; +®_drivevbus { + regulator-name = "usb0-vbus"; + status = "okay"; +}; + &simplefb_lcd { vcc-lcd-supply = <®_dc1sw>; vcc-pg-supply = <®_dldo2>; }; -/* - * FIXME for now we only support host mode and rely on u-boot to have - * turned on Vbus which is controlled by the axp221 pmic on the board. - * - * Once we have axp221 power-supply and vbus-usb support we should switch - * to fully supporting otg. - */ &usb_otg { - dr_mode = "host"; + dr_mode = "otg"; + status = "okay"; +}; + +&usb_power_supply { status = "okay"; }; &usbphy { + pinctrl-names = "default"; + pinctrl-0 = <&usb0_id_detect_pin>; + usb0_id_det-gpio = <&pio 0 15 GPIO_ACTIVE_HIGH>; /* PA15 */ + usb0_vbus_power-supply = <&usb_power_supply>; + usb0_vbus-supply = <®_drivevbus>; usb1_vbus-supply = <®_dldo1>; status = "okay"; }; From 97c6d82b0f0a5a5e3f80a1554ae96c07aaa75dfe Mon Sep 17 00:00:00 2001 From: Hans de Goede Date: Tue, 26 Jul 2016 23:04:31 +0200 Subject: [PATCH 02/31] ARM: dts: sun8i: Add dts file for the Orange Pi PC Plus SBC There is a new Orange Pi PC *Plus* version available now, this is an extended version of the regular Orange Pi PC with sdio wifi and an eMMC. Signed-off-by: Hans de Goede [Maxime: Fix model and compatible] Signed-off-by: Maxime Ripard --- arch/arm/boot/dts/Makefile | 1 + .../boot/dts/sun8i-h3-orangepi-pc-plus.dts | 88 +++++++++++++++++++ 2 files changed, 89 insertions(+) create mode 100644 arch/arm/boot/dts/sun8i-h3-orangepi-pc-plus.dts diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index faacd52370d2..6b3bdb6f7e7f 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -791,6 +791,7 @@ dtb-$(CONFIG_MACH_SUN8I) += \ sun8i-h3-orangepi-2.dtb \ sun8i-h3-orangepi-one.dtb \ sun8i-h3-orangepi-pc.dtb \ + sun8i-h3-orangepi-pc-plus.dtb \ sun8i-h3-orangepi-plus.dtb \ sun8i-r16-parrot.dtb dtb-$(CONFIG_MACH_SUN9I) += \ diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-pc-plus.dts b/arch/arm/boot/dts/sun8i-h3-orangepi-pc-plus.dts new file mode 100644 index 000000000000..851fd2c2cc8c --- /dev/null +++ b/arch/arm/boot/dts/sun8i-h3-orangepi-pc-plus.dts @@ -0,0 +1,88 @@ +/* + * Copyright (C) 2016 Hans de Goede + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/* The Orange Pi PC Plus is an extended version of the regular PC */ +#include "sun8i-h3-orangepi-pc.dts" + +/ { + model = "Xunlong Orange Pi PC Plus"; + compatible = "xunlong,orangepi-pc-plus", "allwinner,sun8i-h3"; + + aliases { + /* ethernet0 is the H3 emac, defined in sun8i-h3.dtsi */ + ethernet1 = &rtl8189ftv; + }; +}; + +&mmc1 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc1_pins_a>; + vmmc-supply = <®_vcc3v3>; + bus-width = <4>; + non-removable; + status = "okay"; + + /* + * Explicitly define the sdio device, so that we can add an ethernet + * alias for it (which e.g. makes u-boot set a mac-address). + */ + rtl8189ftv: sdio_wifi@1 { + reg = <1>; + }; +}; + +&mmc2 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc2_8bit_pins>; + vmmc-supply = <®_vcc3v3>; + bus-width = <8>; + non-removable; + cap-mmc-hw-reset; + status = "okay"; +}; + +&mmc2_8bit_pins { + /* Increase drive strength for DDR modes */ + allwinner,drive = ; + /* eMMC is missing pull-ups */ + allwinner,pull = ; +}; From fbd073102c6910cc3b2f35b98ddc1fea5eb12795 Mon Sep 17 00:00:00 2001 From: Hans de Goede Date: Sat, 9 Jul 2016 22:21:57 +0200 Subject: [PATCH 03/31] ARM: dts: sun8i: Add ethernet1 alias to Orange Pi 2 dts This will allow u-boot to fill in a mac-address for Orange Pi 2 variants which use an sdio wifi without an eeprom for the mac. Signed-off-by: Hans de Goede Signed-off-by: Maxime Ripard --- arch/arm/boot/dts/sun8i-h3-orangepi-2.dts | 10 ++++++++++ 1 file changed, 10 insertions(+) diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-2.dts b/arch/arm/boot/dts/sun8i-h3-orangepi-2.dts index f93f5d1695c4..f89fe00ddec5 100644 --- a/arch/arm/boot/dts/sun8i-h3-orangepi-2.dts +++ b/arch/arm/boot/dts/sun8i-h3-orangepi-2.dts @@ -54,6 +54,8 @@ aliases { serial0 = &uart0; + /* ethernet0 is the H3 emac, defined in sun8i-h3.dtsi */ + ethernet1 = &rtl8189; }; chosen { @@ -131,6 +133,14 @@ bus-width = <4>; non-removable; status = "okay"; + + /* + * Explicitly define the sdio device, so that we can add an ethernet + * alias for it (which e.g. makes u-boot set a mac-address). + */ + rtl8189: sdio_wifi@1 { + reg = <1>; + }; }; &pio { From 614a749a1050fc87bad09ac5d155f269ed66aa80 Mon Sep 17 00:00:00 2001 From: Maxime Ripard Date: Sat, 27 Feb 2016 15:55:29 -0800 Subject: [PATCH 04/31] ARM: dt: axp209: Add AXP209 GPIO driver Add the AXP209 GPIO node to our AXP209 DTSI so that boards can use it. Signed-off-by: Maxime Ripard Acked-by: Linus Walleij --- arch/arm/boot/dts/axp209.dtsi | 6 ++++++ 1 file changed, 6 insertions(+) diff --git a/arch/arm/boot/dts/axp209.dtsi b/arch/arm/boot/dts/axp209.dtsi index afbe89c01df5..675bb0f30825 100644 --- a/arch/arm/boot/dts/axp209.dtsi +++ b/arch/arm/boot/dts/axp209.dtsi @@ -53,6 +53,12 @@ interrupt-controller; #interrupt-cells = <1>; + axp_gpio: gpio { + compatible = "x-powers,axp209-gpio"; + gpio-controller; + #gpio-cells = <2>; + }; + regulators { /* Default work frequency for buck regulators */ x-powers,dcdc-freq = <1500>; From 3d3f05e643dbe79c996803fff8de97cb7209d057 Mon Sep 17 00:00:00 2001 From: Maxime Ripard Date: Sat, 27 Feb 2016 15:56:21 -0800 Subject: [PATCH 05/31] ARM: sun5i: chip: Add status LED The CHIP has a status LED connected to one of the AXP GPIOs. Add the gpio-leds node to be able to use the proper LED framework to control it. Signed-off-by: Maxime Ripard --- arch/arm/boot/dts/sun5i-r8-chip.dts | 10 ++++++++++ 1 file changed, 10 insertions(+) diff --git a/arch/arm/boot/dts/sun5i-r8-chip.dts b/arch/arm/boot/dts/sun5i-r8-chip.dts index f694482bdeb6..b68a12374b35 100644 --- a/arch/arm/boot/dts/sun5i-r8-chip.dts +++ b/arch/arm/boot/dts/sun5i-r8-chip.dts @@ -64,6 +64,16 @@ chosen { stdout-path = "serial0:115200n8"; }; + + leds { + compatible = "gpio-leds"; + + status { + label = "chip:white:status"; + gpios = <&axp_gpio 2 GPIO_ACTIVE_HIGH>; + default-state = "on"; + }; + }; }; &be0 { From 4b09a6faa83705864ff53f3c287800b7244f5a6a Mon Sep 17 00:00:00 2001 From: Stefan Mavrodiev Date: Mon, 15 Aug 2016 10:36:33 +0300 Subject: [PATCH 06/31] ARM: dts: sun8i: Add dts file for Olimex A33-OLinuXino A33-OLinuXino is A33 development board designed by Olimex LTD. It has AXP223 PMU, 1GB DRAM, a micro SD card, one USB-OTG connector, headphone and mic jacks, connector for LiPo battery and optional 4GB NAND Flash. It has two 40-pin headers. One for LCD panel, and one for additional modules. Also there is CSI/DSI connector. Signed-off-by: Stefan Mavrodiev Signed-off-by: Maxime Ripard --- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/sun8i-a33-olinuxino.dts | 226 ++++++++++++++++++++++ 2 files changed, 227 insertions(+) create mode 100644 arch/arm/boot/dts/sun8i-a33-olinuxino.dts diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 6b3bdb6f7e7f..75cd98a86707 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -783,6 +783,7 @@ dtb-$(CONFIG_MACH_SUN8I) += \ sun8i-a33-et-q8-v1.6.dtb \ sun8i-a33-ga10h-v1.1.dtb \ sun8i-a33-ippo-q8h-v1.2.dtb \ + sun8i-a33-olinuxino.dtb \ sun8i-a33-q8-tablet.dtb \ sun8i-a33-sinlinx-sina33.dtb \ sun8i-a83t-allwinner-h8homlet-v2.dtb \ diff --git a/arch/arm/boot/dts/sun8i-a33-olinuxino.dts b/arch/arm/boot/dts/sun8i-a33-olinuxino.dts new file mode 100644 index 000000000000..9ea637e82b2d --- /dev/null +++ b/arch/arm/boot/dts/sun8i-a33-olinuxino.dts @@ -0,0 +1,226 @@ +/* + * Copyright 2016 - Stefan Mavrodiev + * Olimex LTD. + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; +#include "sun8i-a33.dtsi" +#include "sunxi-common-regulators.dtsi" + +#include +#include + +/ { + model = "Olimex A33-OLinuXino"; + compatible = "olimex,a33-olinuxino","allwinner,sun8i-a33"; + + aliases { + serial0 = &uart0; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&led_pin_olinuxino>; + + green { + label = "a33-olinuxino:green:usr"; + gpios = <&pio 1 7 GPIO_ACTIVE_HIGH>; + }; + }; +}; + +&ehci0 { + status = "okay"; +}; + +&mmc0 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_olinuxino>; + vmmc-supply = <®_dcdc1>; + bus-width = <4>; + cd-gpios = <&pio 1 4 GPIO_ACTIVE_HIGH>; /* PB4 */ + cd-inverted; + status = "okay"; +}; + +&ohci0 { + status = "okay"; +}; + +&pio { + led_pin_olinuxino: led_pins@0 { + allwinner,pins = "PB7"; + allwinner,function = "gpio_out"; + allwinner,drive = ; + allwinner,pull = ; + }; + + mmc0_cd_pin_olinuxino: mmc0_cd_pin@0 { + allwinner,pins = "PB4"; + allwinner,function = "gpio_in"; + allwinner,drive = ; + allwinner,pull = ; + }; + + usb0_id_detect_pin: usb0_id_detect_pin@0 { + allwinner,pins = "PB3"; + allwinner,function = "gpio_in"; + allwinner,drive = ; + allwinner,pull = ; + }; +}; + +&r_rsb { + status = "okay"; + + axp22x: pmic@3a3 { + compatible = "x-powers,axp223"; + reg = <0x3a3>; + interrupt-parent = <&nmi_intc>; + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + eldoin-supply = <®_dcdc1>; + x-powers,drive-vbus-en; + }; +}; + +#include "axp22x.dtsi" + +®_aldo1 { + regulator-always-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-io"; +}; + +®_aldo2 { + regulator-always-on; + regulator-min-microvolt = <2350000>; + regulator-max-microvolt = <2650000>; + regulator-name = "vdd-dll"; +}; + +®_aldo3 { + regulator-always-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-avcc"; +}; + +®_dc1sw { + regulator-name = "vcc-lcd"; +}; + +®_dc5ldo { + regulator-always-on; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1400000>; + regulator-name = "vdd-cpus"; +}; + +®_dcdc1 { + regulator-always-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-3v3"; +}; + +®_dcdc2 { + regulator-always-on; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1400000>; + regulator-name = "vdd-sys"; +}; + +®_dcdc3 { + regulator-always-on; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1400000>; + regulator-name = "vdd-cpu"; +}; + +®_dcdc5 { + regulator-always-on; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <1500000>; + regulator-name = "vcc-dram"; +}; + +®_drivevbus { + regulator-name = "usb0-vbus"; + status = "okay"; +}; + +®_rtc_ldo { + regulator-name = "vcc-rtc"; +}; + +&simplefb_lcd { + vcc-lcd-supply = <®_dc1sw>; +}; + +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_pins_b>; + status = "okay"; +}; + +&usb_otg { + dr_mode = "otg"; + status = "okay"; +}; + +&usb_power_supply { + status = "okay"; +}; + +&usbphy { + pinctrl-names = "default"; + pinctrl-0 = <&usb0_id_detect_pin>; + usb0_id_det-gpios = <&pio 1 3 GPIO_ACTIVE_HIGH>; /* PB3 */ + usb0_vbus_power-supply = <&usb_power_supply>; + usb0_vbus-supply = <®_drivevbus>; + status = "okay"; +}; From dc36787fedf0248c752cf1c53092104d54489617 Mon Sep 17 00:00:00 2001 From: Hans de Goede Date: Sun, 7 Aug 2016 16:16:44 +0200 Subject: [PATCH 07/31] ARM: dts: sun8i: Add dts file for the Orange Pi Lite SBC The Orange Pi Lite SBC is a small H3 based SBC, with 512MB RAM, micro-sd slot, HDMI out, 2 USB-A connectors, 1 micro-USB connector, sdio attached rtl8189ftv wifi and an ir receiver. Signed-off-by: Hans de Goede Acked-by: Chen-Yu Tsai Signed-off-by: Maxime Ripard --- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/sun8i-h3-orangepi-lite.dts | 178 +++++++++++++++++++ 2 files changed, 179 insertions(+) create mode 100644 arch/arm/boot/dts/sun8i-h3-orangepi-lite.dts diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 75cd98a86707..55a3e9d8545a 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -790,6 +790,7 @@ dtb-$(CONFIG_MACH_SUN8I) += \ sun8i-a83t-cubietruck-plus.dtb \ sun8i-h3-bananapi-m2-plus.dtb \ sun8i-h3-orangepi-2.dtb \ + sun8i-h3-orangepi-lite.dtb \ sun8i-h3-orangepi-one.dtb \ sun8i-h3-orangepi-pc.dtb \ sun8i-h3-orangepi-pc-plus.dtb \ diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-lite.dts b/arch/arm/boot/dts/sun8i-h3-orangepi-lite.dts new file mode 100644 index 000000000000..1550fee1ec68 --- /dev/null +++ b/arch/arm/boot/dts/sun8i-h3-orangepi-lite.dts @@ -0,0 +1,178 @@ +/* + * Copyright (C) 2016 Hans de Goede + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; +#include "sun8i-h3.dtsi" +#include "sunxi-common-regulators.dtsi" + +#include +#include +#include + +/ { + model = "Xunlong Orange Pi Lite"; + compatible = "xunlong,orangepi-lite", "allwinner,sun8i-h3"; + + aliases { + /* The H3 emac is not used so the wifi is ethernet0 */ + ethernet0 = &rtl8189ftv; + serial0 = &uart0; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&leds_opc>, <&leds_r_opc>; + + pwr_led { + label = "orangepi:green:pwr"; + gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; + default-state = "on"; + }; + + status_led { + label = "orangepi:red:status"; + gpios = <&pio 0 15 GPIO_ACTIVE_HIGH>; + }; + }; + + r_gpio_keys { + compatible = "gpio-keys"; + pinctrl-names = "default"; + pinctrl-0 = <&sw_r_opc>; + + sw4 { + label = "sw4"; + linux,code = ; + gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>; + }; + }; +}; + +&ehci1 { + status = "okay"; +}; + +&ehci2 { + status = "okay"; +}; + +&ir { + pinctrl-names = "default"; + pinctrl-0 = <&ir_pins_a>; + status = "okay"; +}; + +&mmc0 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>; + vmmc-supply = <®_vcc3v3>; + bus-width = <4>; + cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */ + cd-inverted; + status = "okay"; +}; + +&mmc1 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc1_pins_a>; + vmmc-supply = <®_vcc3v3>; + bus-width = <4>; + non-removable; + status = "okay"; + + /* + * Explicitly define the sdio device, so that we can add an ethernet + * alias for it (which e.g. makes u-boot set a mac-address). + */ + rtl8189ftv: sdio_wifi@1 { + reg = <1>; + }; +}; + +&ohci1 { + status = "okay"; +}; + +&ohci2 { + status = "okay"; +}; + +&pio { + leds_opc: led_pins@0 { + allwinner,pins = "PA15"; + allwinner,function = "gpio_out"; + allwinner,drive = ; + allwinner,pull = ; + }; +}; + +&r_pio { + leds_r_opc: led_pins@0 { + allwinner,pins = "PL10"; + allwinner,function = "gpio_out"; + allwinner,drive = ; + allwinner,pull = ; + }; + + sw_r_opc: key_pins@0 { + allwinner,pins = "PL3"; + allwinner,function = "gpio_in"; + allwinner,drive = ; + allwinner,pull = ; + }; +}; + +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_pins_a>; + status = "okay"; +}; + +&usbphy { + /* USB VBUS is always on */ + status = "okay"; +}; From 9d3ee5754335416bde2e75e93048294b8423e7c6 Mon Sep 17 00:00:00 2001 From: Hans de Goede Date: Mon, 8 Aug 2016 21:43:11 +0200 Subject: [PATCH 08/31] ARM: dts: sun8i: Use sun8i-reference-design-tablet for gt90h dts This results in quite a nice cleanup for this dts file. As an added bonus this also enables full otg support. I've tested that this works as advertised. Signed-off-by: Hans de Goede Acked-by: Chen-Yu Tsai Signed-off-by: Maxime Ripard --- arch/arm/boot/dts/sun8i-a23-gt90h-v4.dts | 192 +---------------------- 1 file changed, 1 insertion(+), 191 deletions(-) diff --git a/arch/arm/boot/dts/sun8i-a23-gt90h-v4.dts b/arch/arm/boot/dts/sun8i-a23-gt90h-v4.dts index b2ce284a65a2..f27ebbbeac09 100644 --- a/arch/arm/boot/dts/sun8i-a23-gt90h-v4.dts +++ b/arch/arm/boot/dts/sun8i-a23-gt90h-v4.dts @@ -42,70 +42,18 @@ /dts-v1/; #include "sun8i-a23.dtsi" -#include "sunxi-common-regulators.dtsi" - -#include -#include -#include -#include +#include "sun8i-reference-design-tablet.dtsi" / { model = "Allwinner GT90H Dual Core Tablet (v4)"; compatible = "allwinner,gt90h-v4", "allwinner,sun8i-a23"; - - aliases { - serial0 = &r_uart; - }; - - backlight: backlight { - compatible = "pwm-backlight"; - pinctrl-names = "default"; - pinctrl-0 = <&bl_en_pin_gt90h>; - pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>; - brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>; - default-brightness-level = <8>; - enable-gpios = <&pio 7 6 GPIO_ACTIVE_HIGH>; /* PH6 */ - }; - - chosen { - stdout-path = "serial0:115200n8"; - }; }; &ehci0 { status = "okay"; }; -&i2c0 { - pinctrl-names = "default"; - pinctrl-0 = <&i2c0_pins_a>; - status = "okay"; -}; - -&i2c1 { - pinctrl-names = "default"; - pinctrl-0 = <&i2c1_pins_a>; - status = "okay"; -}; - &lradc { - vref-supply = <®_vcc3v0>; - status = "okay"; - - button@200 { - label = "Volume Up"; - linux,code = ; - channel = <0>; - voltage = <200000>; - }; - - button@400 { - label = "Volume Down"; - linux,code = ; - channel = <0>; - voltage = <400000>; - }; - button@600 { label = "Back"; linux,code = ; @@ -114,144 +62,6 @@ }; }; -&mmc0 { - pinctrl-names = "default"; - pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_gt90h>; - vmmc-supply = <®_aldo1>; - bus-width = <4>; - cd-gpios = <&pio 1 4 GPIO_ACTIVE_HIGH>; /* PB4 */ - cd-inverted; - status = "okay"; -}; - -&pio { - bl_en_pin_gt90h: bl_en_pin@0 { - allwinner,pins = "PH6"; - allwinner,function = "gpio_in"; - allwinner,drive = ; - allwinner,pull = ; - }; - - mmc0_cd_pin_gt90h: mmc0_cd_pin@0 { - allwinner,pins = "PB4"; - allwinner,function = "gpio_in"; - allwinner,drive = ; - allwinner,pull = ; - }; -}; - -&pwm { - pinctrl-names = "default"; - pinctrl-0 = <&pwm0_pins>; - status = "okay"; -}; - -&r_rsb { - status = "okay"; - - axp22x: pmic@3a3 { - compatible = "x-powers,axp223"; - reg = <0x3a3>; - interrupt-parent = <&nmi_intc>; - interrupts = <0 IRQ_TYPE_LEVEL_LOW>; - eldoin-supply = <®_dcdc1>; - }; -}; - -&r_uart { - pinctrl-names = "default"; - pinctrl-0 = <&r_uart_pins_a>; - status = "okay"; -}; - -#include "axp22x.dtsi" - -®_aldo1 { - regulator-always-on; - regulator-min-microvolt = <3000000>; - regulator-max-microvolt = <3000000>; - regulator-name = "vcc-io"; -}; - -®_aldo2 { - regulator-always-on; - regulator-min-microvolt = <2350000>; - regulator-max-microvolt = <2650000>; - regulator-name = "vdd-dll"; -}; - -®_aldo3 { - regulator-always-on; - regulator-min-microvolt = <2700000>; - regulator-max-microvolt = <3300000>; - regulator-name = "vcc-pll-avcc"; -}; - -®_dc1sw { - regulator-name = "vcc-lcd"; -}; - -®_dc5ldo { - regulator-always-on; - regulator-min-microvolt = <900000>; - regulator-max-microvolt = <1400000>; - regulator-name = "vdd-cpus"; -}; - -®_dcdc1 { - regulator-always-on; - regulator-min-microvolt = <3000000>; - regulator-max-microvolt = <3000000>; - regulator-name = "vcc-3v0"; -}; - -®_dcdc2 { - regulator-always-on; - regulator-min-microvolt = <900000>; - regulator-max-microvolt = <1400000>; - regulator-name = "vdd-sys"; -}; - -®_dcdc3 { - regulator-always-on; - regulator-min-microvolt = <900000>; - regulator-max-microvolt = <1400000>; - regulator-name = "vdd-cpu"; -}; - -®_dcdc5 { - regulator-always-on; - regulator-min-microvolt = <1500000>; - regulator-max-microvolt = <1500000>; - regulator-name = "vcc-dram"; -}; - -®_dldo1 { - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - regulator-name = "vcc-wifi"; -}; - -®_rtc_ldo { - regulator-name = "vcc-rtc"; -}; - -&simplefb_lcd { - vcc-lcd-supply = <®_dc1sw>; -}; - -/* - * FIXME for now we only support host mode and rely on u-boot to have - * turned on Vbus which is controlled by the axp223 pmic on the board. - * - * Once we have axp223 support we should switch to fully supporting otg. - */ -&usb_otg { - dr_mode = "host"; - status = "okay"; -}; - &usbphy { usb1_vbus-supply = <®_dldo1>; - status = "okay"; }; From 835dbe8ffafa45907495811cb2f3a57b2cccfa27 Mon Sep 17 00:00:00 2001 From: Hans de Goede Date: Mon, 8 Aug 2016 21:43:12 +0200 Subject: [PATCH 09/31] ARM: dts: sun8i: Add dt node for rtl8703as wifi chip on ga10h The ga10h tablet has a rtl8703as wifi chip, add a dt node describing it. This enables usage of wifi on this tablet (together with the out of tree rtl8732bs driver). Signed-off-by: Hans de Goede Acked-by: Chen-Yu Tsai Signed-off-by: Maxime Ripard --- arch/arm/boot/dts/sun8i-a33-ga10h-v1.1.dts | 18 ++++++++++++++++++ 1 file changed, 18 insertions(+) diff --git a/arch/arm/boot/dts/sun8i-a33-ga10h-v1.1.dts b/arch/arm/boot/dts/sun8i-a33-ga10h-v1.1.dts index 65660324005c..de6269dcac3a 100644 --- a/arch/arm/boot/dts/sun8i-a33-ga10h-v1.1.dts +++ b/arch/arm/boot/dts/sun8i-a33-ga10h-v1.1.dts @@ -47,6 +47,11 @@ / { model = "Allwinner GA10H Quad Core Tablet (v1.1)"; compatible = "allwinner,ga10h-v1.1", "allwinner,sun8i-a33"; + + aliases { + /* Make u-boot set mac-address for rtl8703as (no eeprom) */ + ethernet0 = &rtl8703as; + }; }; &ehci0 { @@ -62,6 +67,19 @@ }; }; +&mmc1 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc1_pins_a>; + vmmc-supply = <®_dldo1>; + bus-width = <4>; + non-removable; + status = "okay"; + + rtl8703as: sdio_wifi@1 { + reg = <1>; + }; +}; + &ohci0 { status = "okay"; }; From e8552107ae5845dd1d281cddca026ef0e4d30c80 Mon Sep 17 00:00:00 2001 From: Hans de Goede Date: Mon, 8 Aug 2016 21:43:13 +0200 Subject: [PATCH 10/31] ARM: dts: sun8i: reference-design-tablet: Add gsl1680 touchscreen node Almost all sun8i tablets use a gsl1680 touchscreen controller, so add a node describing it to reference-design-tablet.dtsi. Almost all, but not all, so mark it as disabled by default (dts files will also need to supply a firmware-name and resolution info). Signed-off-by: Hans de Goede Acked-by: Chen-Yu Tsai Signed-off-by: Maxime Ripard --- .../dts/sun8i-reference-design-tablet.dtsi | 28 +++++++++++++++++++ 1 file changed, 28 insertions(+) diff --git a/arch/arm/boot/dts/sun8i-reference-design-tablet.dtsi b/arch/arm/boot/dts/sun8i-reference-design-tablet.dtsi index 9d9036140511..f29897c40ae8 100644 --- a/arch/arm/boot/dts/sun8i-reference-design-tablet.dtsi +++ b/arch/arm/boot/dts/sun8i-reference-design-tablet.dtsi @@ -63,6 +63,27 @@ }; }; +&i2c0 { + /* + * The gsl1680 is rated at 400KHz and it will not work reliable at + * 100KHz, this has been confirmed on multiple different q8 tablets. + * The gsl1680 is the only device on this bus. + */ + clock-frequency = <400000>; + + gsl1680: touchscreen@40 { + compatible = "silead,gsl1680"; + reg = <0x40>; + interrupt-parent = <&pio>; + interrupts = <1 5 IRQ_TYPE_EDGE_FALLING>; /* PB5 */ + pinctrl-names = "default"; + pinctrl-0 = <&ts_power_pin>; + power-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */ + /* Most tablets use this touchscreen, but not all */ + status = "disabled"; + }; +}; + &mmc0 { pinctrl-names = "default"; pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>; @@ -88,6 +109,13 @@ allwinner,pull = ; }; + ts_power_pin: ts_power_pin@0 { + allwinner,pins = "PH1"; + allwinner,function = "gpio_out"; + allwinner,drive = ; + allwinner,pull = ; + }; + usb0_id_detect_pin: usb0_id_detect_pin@0 { allwinner,pins = "PH8"; allwinner,function = "gpio_in"; From 9caf39bfb98a59848ffe05f19a0bbab65220f7e5 Mon Sep 17 00:00:00 2001 From: Chen-Yu Tsai Date: Fri, 19 Aug 2016 15:42:24 +0800 Subject: [PATCH 11/31] ARM: dts: sun9i: a80-optimus: Add device node for AC100 Signed-off-by: Chen-Yu Tsai Signed-off-by: Maxime Ripard --- arch/arm/boot/dts/sun9i-a80-optimus.dts | 24 ++++++++++++++++++++++++ 1 file changed, 24 insertions(+) diff --git a/arch/arm/boot/dts/sun9i-a80-optimus.dts b/arch/arm/boot/dts/sun9i-a80-optimus.dts index 7fd22e888602..e35c06c162a7 100644 --- a/arch/arm/boot/dts/sun9i-a80-optimus.dts +++ b/arch/arm/boot/dts/sun9i-a80-optimus.dts @@ -322,6 +322,30 @@ }; }; }; + + ac100: codec@e89 { + compatible = "x-powers,ac100"; + reg = <0xe89>; + + ac100_codec: codec { + compatible = "x-powers,ac100-codec"; + interrupt-parent = <&r_pio>; + interrupts = <0 9 IRQ_TYPE_LEVEL_LOW>; /* PL9 */ + #clock-cells = <0>; + clock-output-names = "4M_adda"; + }; + + ac100_rtc: rtc { + compatible = "x-powers,ac100-rtc"; + interrupt-parent = <&nmi_intc>; + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + clocks = <&ac100_codec>; + #clock-cells = <1>; + clock-output-names = "cko1_rtc", + "cko2_rtc", + "cko3_rtc"; + }; + }; }; #include "axp809.dtsi" From 38f151d410056149c0a539bbaa2873db4d3fc9a4 Mon Sep 17 00:00:00 2001 From: Chen-Yu Tsai Date: Fri, 19 Aug 2016 15:42:25 +0800 Subject: [PATCH 12/31] ARM: dts: sun9i: cubieboard4: Add device node for AC100 Signed-off-by: Chen-Yu Tsai Signed-off-by: Maxime Ripard --- arch/arm/boot/dts/sun9i-a80-cubieboard4.dts | 24 +++++++++++++++++++++ 1 file changed, 24 insertions(+) diff --git a/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts b/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts index 1526b41c70f1..cf2f4b72a841 100644 --- a/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts +++ b/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts @@ -250,6 +250,30 @@ }; }; }; + + ac100: codec@e89 { + compatible = "x-powers,ac100"; + reg = <0xe89>; + + ac100_codec: codec { + compatible = "x-powers,ac100-codec"; + interrupt-parent = <&r_pio>; + interrupts = <0 9 IRQ_TYPE_LEVEL_LOW>; /* PL9 */ + #clock-cells = <0>; + clock-output-names = "4M_adda"; + }; + + ac100_rtc: rtc { + compatible = "x-powers,ac100-rtc"; + interrupt-parent = <&nmi_intc>; + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + clocks = <&ac100_codec>; + #clock-cells = <1>; + clock-output-names = "cko1_rtc", + "cko2_rtc", + "cko3_rtc"; + }; + }; }; #include "axp809.dtsi" From 162669876bbecf6fb4d5b69f2cc79635565c6c3f Mon Sep 17 00:00:00 2001 From: Chen-Yu Tsai Date: Fri, 19 Aug 2016 15:42:26 +0800 Subject: [PATCH 13/31] ARM: dts: sun9i: Switch to the AC100 RTC clock outputs for osc32k The 32.768 kHz clock inside the A80 SoC is fed from an external source, typically the AC100 RTC module. Make the osc32k placeholder a fixed-factor clock so board dts files can specify its source. Signed-off-by: Chen-Yu Tsai Signed-off-by: Maxime Ripard --- arch/arm/boot/dts/sun9i-a80-cubieboard4.dts | 5 +++++ arch/arm/boot/dts/sun9i-a80-optimus.dts | 5 +++++ arch/arm/boot/dts/sun9i-a80.dtsi | 11 +++++------ 3 files changed, 15 insertions(+), 6 deletions(-) diff --git a/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts b/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts index cf2f4b72a841..04b014603659 100644 --- a/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts +++ b/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts @@ -103,6 +103,11 @@ allwinner,drive = ; }; +&osc32k { + /* osc32k input is from AC100 */ + clocks = <&ac100_rtc 0>; +}; + &pio { led_pins_cubieboard4: led-pins@0 { allwinner,pins = "PH6", "PH17"; diff --git a/arch/arm/boot/dts/sun9i-a80-optimus.dts b/arch/arm/boot/dts/sun9i-a80-optimus.dts index e35c06c162a7..fd874ded890e 100644 --- a/arch/arm/boot/dts/sun9i-a80-optimus.dts +++ b/arch/arm/boot/dts/sun9i-a80-optimus.dts @@ -152,6 +152,11 @@ status = "okay"; }; +&osc32k { + /* osc32k input is from AC100 */ + clocks = <&ac100_rtc 0>; +}; + &pio { led_pins_optimus: led-pins@0 { allwinner,pins = "PH0", "PH1"; diff --git a/arch/arm/boot/dts/sun9i-a80.dtsi b/arch/arm/boot/dts/sun9i-a80.dtsi index f68b3242b33a..24e3cac4f571 100644 --- a/arch/arm/boot/dts/sun9i-a80.dtsi +++ b/arch/arm/boot/dts/sun9i-a80.dtsi @@ -148,15 +148,14 @@ /* * The 32k clock is from an external source, normally the - * AC100 codec/RTC chip. This clock is by default enabled - * and clocked at 32768 Hz, from the oscillator connected - * to the AC100. It is configurable, but no such driver or - * bindings exist yet. + * AC100 codec/RTC chip. This serves as a placeholder for + * board dts files to specify the source. */ osc32k: osc32k_clk { #clock-cells = <0>; - compatible = "fixed-clock"; - clock-frequency = <32768>; + compatible = "fixed-factor-clock"; + clock-div = <1>; + clock-mult = <1>; clock-output-names = "osc32k"; }; From a343dfdd9612855395cb6a65a8907dd7256ef80e Mon Sep 17 00:00:00 2001 From: Hans de Goede Date: Thu, 18 Aug 2016 20:02:15 +0200 Subject: [PATCH 14/31] ARM: dts: sun6i: colorfly-e708-q1: Remove unused mma8452_int_e708_q1 node The presence of the mma8452_int_e708_q1 node is a copy and paste error, remove it. Signed-off-by: Hans de Goede Acked-by: Chen-Yu Tsai Signed-off-by: Maxime Ripard --- arch/arm/boot/dts/sun6i-a31s-colorfly-e708-q1.dts | 7 ------- 1 file changed, 7 deletions(-) diff --git a/arch/arm/boot/dts/sun6i-a31s-colorfly-e708-q1.dts b/arch/arm/boot/dts/sun6i-a31s-colorfly-e708-q1.dts index 9040bb9f80f3..34d8710a7c46 100644 --- a/arch/arm/boot/dts/sun6i-a31s-colorfly-e708-q1.dts +++ b/arch/arm/boot/dts/sun6i-a31s-colorfly-e708-q1.dts @@ -93,13 +93,6 @@ }; &pio { - mma8452_int_e708_q1: mma8452_int_pin@0 { - allwinner,pins = "PA9"; - allwinner,function = "gpio_in"; - allwinner,drive = ; - allwinner,pull = ; - }; - mmc0_cd_pin_e708_q1: mmc0_cd_pin@0 { allwinner,pins = "PA8"; allwinner,function = "gpio_in"; From b32aea85144ff046b2f8f40c48113d1a06086239 Mon Sep 17 00:00:00 2001 From: Hans de Goede Date: Thu, 18 Aug 2016 20:02:16 +0200 Subject: [PATCH 15/31] ARM: dts: sun6i: Add sun6i-reference-design-tablet.dtsi Just like with a13/a23/a33 most a31 tablets are derived from the same reference design. Add a .dtsi file with all the common bits to avoid endless copy and pasting of these. The sun6i-reference-design-tablet.dtsi this commit adds is a copy of sun6i-a31s-colorfly-e708-q1.dts with a few tablet specific bits removed / left in sun6i-a31s-colorfly-e708-q1.dts. Signed-off-by: Hans de Goede Acked-by: Chen-Yu Tsai Signed-off-by: Maxime Ripard --- .../boot/dts/sun6i-a31s-colorfly-e708-q1.dts | 147 +------------ .../dts/sun6i-reference-design-tablet.dtsi | 193 ++++++++++++++++++ 2 files changed, 194 insertions(+), 146 deletions(-) create mode 100644 arch/arm/boot/dts/sun6i-reference-design-tablet.dtsi diff --git a/arch/arm/boot/dts/sun6i-a31s-colorfly-e708-q1.dts b/arch/arm/boot/dts/sun6i-a31s-colorfly-e708-q1.dts index 34d8710a7c46..882a4d89fa22 100644 --- a/arch/arm/boot/dts/sun6i-a31s-colorfly-e708-q1.dts +++ b/arch/arm/boot/dts/sun6i-a31s-colorfly-e708-q1.dts @@ -42,32 +42,11 @@ /dts-v1/; #include "sun6i-a31s.dtsi" -#include "sunxi-common-regulators.dtsi" - -#include -#include -#include +#include "sun6i-reference-design-tablet.dtsi" / { model = "Colorfly E708 Q1 tablet"; compatible = "colorfly,e708-q1", "allwinner,sun6i-a31s"; - - aliases { - serial0 = &uart0; - }; - - chosen { - stdout-path = "serial0:115200n8"; - }; -}; - -&cpu0 { - cpu-supply = <®_dcdc3>; -}; - -&ehci0 { - /* rtl8188etv wifi is connected here */ - status = "okay"; }; &lradc { @@ -82,136 +61,12 @@ }; }; -&mmc0 { - pinctrl-names = "default"; - pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_e708_q1>; - vmmc-supply = <®_dcdc1>; - bus-width = <4>; - cd-gpios = <&pio 0 8 GPIO_ACTIVE_HIGH>; /* PA8 */ - cd-inverted; - status = "okay"; -}; - -&pio { - mmc0_cd_pin_e708_q1: mmc0_cd_pin@0 { - allwinner,pins = "PA8"; - allwinner,function = "gpio_in"; - allwinner,drive = ; - allwinner,pull = ; - }; - - usb0_id_detect_pin: usb0_id_detect_pin@0 { - allwinner,pins = "PA15"; - allwinner,function = "gpio_in"; - allwinner,drive = ; - allwinner,pull = ; - }; -}; - -&p2wi { - status = "okay"; - - axp22x: pmic@68 { - compatible = "x-powers,axp221"; - reg = <0x68>; - interrupt-parent = <&nmi_intc>; - interrupts = <0 IRQ_TYPE_LEVEL_LOW>; - drivevbus-supply = <®_vcc5v0>; - x-powers,drive-vbus-en; - }; -}; - -#include "axp22x.dtsi" - -®_aldo3 { - regulator-always-on; - regulator-min-microvolt = <2700000>; - regulator-max-microvolt = <3300000>; - regulator-name = "avcc"; -}; - -®_dc1sw { - regulator-name = "vcc-lcd"; -}; - -®_dc5ldo { - regulator-always-on; - regulator-min-microvolt = <700000>; - regulator-max-microvolt = <1320000>; - regulator-name = "vdd-cpus"; /* This is an educated guess */ -}; - -®_dcdc1 { - regulator-always-on; - regulator-min-microvolt = <3000000>; - regulator-max-microvolt = <3000000>; - regulator-name = "vcc-3v0"; -}; - -®_dcdc2 { - regulator-min-microvolt = <700000>; - regulator-max-microvolt = <1320000>; - regulator-name = "vdd-gpu"; -}; - -®_dcdc3 { - regulator-always-on; - regulator-min-microvolt = <700000>; - regulator-max-microvolt = <1320000>; - regulator-name = "vdd-cpu"; -}; - -®_dcdc4 { - regulator-always-on; - regulator-min-microvolt = <700000>; - regulator-max-microvolt = <1320000>; - regulator-name = "vdd-sys-dll"; -}; - -®_dcdc5 { - regulator-always-on; - regulator-min-microvolt = <1500000>; - regulator-max-microvolt = <1500000>; - regulator-name = "vcc-dram"; -}; - -®_dldo1 { - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - regulator-name = "vcc-wifi"; -}; - ®_dldo2 { regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; regulator-name = "vcc-pg"; }; -®_drivevbus { - regulator-name = "usb0-vbus"; - status = "okay"; -}; - &simplefb_lcd { - vcc-lcd-supply = <®_dc1sw>; vcc-pg-supply = <®_dldo2>; }; - -&usb_otg { - dr_mode = "otg"; - status = "okay"; -}; - -&usb_power_supply { - status = "okay"; -}; - -&usbphy { - pinctrl-names = "default"; - pinctrl-0 = <&usb0_id_detect_pin>; - usb0_id_det-gpio = <&pio 0 15 GPIO_ACTIVE_HIGH>; /* PA15 */ - usb0_vbus_power-supply = <&usb_power_supply>; - usb0_vbus-supply = <®_drivevbus>; - usb1_vbus-supply = <®_dldo1>; - status = "okay"; -}; diff --git a/arch/arm/boot/dts/sun6i-reference-design-tablet.dtsi b/arch/arm/boot/dts/sun6i-reference-design-tablet.dtsi new file mode 100644 index 000000000000..0c434304e040 --- /dev/null +++ b/arch/arm/boot/dts/sun6i-reference-design-tablet.dtsi @@ -0,0 +1,193 @@ +/* + * Copyright 2016 Hans de Goede + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +#include "sunxi-common-regulators.dtsi" + +#include +#include +#include + +/ { + aliases { + serial0 = &uart0; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; +}; + +&cpu0 { + cpu-supply = <®_dcdc3>; +}; + +&ehci0 { + /* Wifi is connected here */ + status = "okay"; +}; + +&mmc0 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_e708_q1>; + vmmc-supply = <®_dcdc1>; + bus-width = <4>; + cd-gpios = <&pio 0 8 GPIO_ACTIVE_HIGH>; /* PA8 */ + cd-inverted; + status = "okay"; +}; + +&pio { + mmc0_cd_pin_e708_q1: mmc0_cd_pin@0 { + allwinner,pins = "PA8"; + allwinner,function = "gpio_in"; + allwinner,drive = ; + allwinner,pull = ; + }; + + usb0_id_detect_pin: usb0_id_detect_pin@0 { + allwinner,pins = "PA15"; + allwinner,function = "gpio_in"; + allwinner,drive = ; + allwinner,pull = ; + }; +}; + +&p2wi { + status = "okay"; + + axp22x: pmic@68 { + compatible = "x-powers,axp221"; + reg = <0x68>; + interrupt-parent = <&nmi_intc>; + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + drivevbus-supply = <®_vcc5v0>; + x-powers,drive-vbus-en; + }; +}; + +#include "axp22x.dtsi" + +®_aldo3 { + regulator-always-on; + regulator-min-microvolt = <2700000>; + regulator-max-microvolt = <3300000>; + regulator-name = "avcc"; +}; + +®_dc1sw { + regulator-name = "vcc-lcd"; +}; + +®_dc5ldo { + regulator-always-on; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1320000>; + regulator-name = "vdd-cpus"; /* This is an educated guess */ +}; + +®_dcdc1 { + regulator-always-on; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-name = "vcc-3v0"; +}; + +®_dcdc2 { + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1320000>; + regulator-name = "vdd-gpu"; +}; + +®_dcdc3 { + regulator-always-on; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1320000>; + regulator-name = "vdd-cpu"; +}; + +®_dcdc4 { + regulator-always-on; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1320000>; + regulator-name = "vdd-sys-dll"; +}; + +®_dcdc5 { + regulator-always-on; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <1500000>; + regulator-name = "vcc-dram"; +}; + +®_dldo1 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-wifi"; +}; + +®_drivevbus { + regulator-name = "usb0-vbus"; + status = "okay"; +}; + +&simplefb_lcd { + vcc-lcd-supply = <®_dc1sw>; +}; + +&usb_otg { + dr_mode = "otg"; + status = "okay"; +}; + +&usb_power_supply { + status = "okay"; +}; + +&usbphy { + pinctrl-names = "default"; + pinctrl-0 = <&usb0_id_detect_pin>; + usb0_id_det-gpio = <&pio 0 15 GPIO_ACTIVE_HIGH>; /* PA15 */ + usb0_vbus_power-supply = <&usb_power_supply>; + usb0_vbus-supply = <®_drivevbus>; + usb1_vbus-supply = <®_dldo1>; + status = "okay"; +}; From f0b631edb8a1f66e6171150d54c1533accb10b04 Mon Sep 17 00:00:00 2001 From: Hans de Goede Date: Thu, 18 Aug 2016 20:02:17 +0200 Subject: [PATCH 16/31] ARM: dts: sun6i: Add new dts file for tablets using the inet-q972 PCB Add a dts file for tablets using the generic inet-q972 PCB. Tablets with this PCB feature a mini-hdmi output, micro-usb usb-host, micro-usb usb-otg, 3.5mm headphone jack, a micro sd slot, (mini) power-barrel and an usb wifi module. This has been tested on a 9.7" 1024x768 qware qw tb9718-qhd tablet. Signed-off-by: Hans de Goede Acked-by: Chen-Yu Tsai Signed-off-by: Maxime Ripard --- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/sun6i-a31s-inet-q972.dts | 100 +++++++++++++++++++++ 2 files changed, 101 insertions(+) create mode 100644 arch/arm/boot/dts/sun6i-a31s-inet-q972.dts diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 55a3e9d8545a..1ec7fe99de33 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -743,6 +743,7 @@ dtb-$(CONFIG_MACH_SUN6I) += \ sun6i-a31-mele-a1000g-quad.dtb \ sun6i-a31s-colorfly-e708-q1.dtb \ sun6i-a31s-cs908.dtb \ + sun6i-a31s-inet-q972.dtb \ sun6i-a31s-primo81.dtb \ sun6i-a31s-sina31s.dtb \ sun6i-a31s-sinovoip-bpi-m2.dtb \ diff --git a/arch/arm/boot/dts/sun6i-a31s-inet-q972.dts b/arch/arm/boot/dts/sun6i-a31s-inet-q972.dts new file mode 100644 index 000000000000..e584e6b186a7 --- /dev/null +++ b/arch/arm/boot/dts/sun6i-a31s-inet-q972.dts @@ -0,0 +1,100 @@ +/* + * Copyright 2016 Hans de Goede + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; +#include "sun6i-a31s.dtsi" +#include "sun6i-reference-design-tablet.dtsi" + +/ { + model = "iNet Q972 tablet"; + compatible = "inet-tek,inet-q972", "allwinner,sun6i-a31s"; +}; + +&ehci1 { + status = "okay"; +}; + +&i2c1 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_pins_a>; + status = "okay"; + + ft5406ee8: touchscreen@38 { + compatible = "edt,edt-ft5406"; + reg = <0x38>; + interrupt-parent = <&pio>; + interrupts = <0 3 IRQ_TYPE_LEVEL_HIGH>; /* PA3 */ + touchscreen-size-x = <768>; + touchscreen-size-y = <1024>; + touchscreen-swapped-x-y; + }; +}; + +&lradc { + vref-supply = <®_aldo3>; + status = "okay"; + + button@200 { + label = "Volume Down"; + linux,code = ; + channel = <0>; + voltage = <200000>; + }; + + button@900 { + label = "Volume Up"; + linux,code = ; + channel = <0>; + voltage = <900000>; + }; + + button@1200 { + label = "Back"; + linux,code = ; + channel = <0>; + voltage = <1200000>; + }; +}; + +&ohci1 { + status = "okay"; +}; From d7b843df13ea3a19580bf5eb109b1fa5a89a338c Mon Sep 17 00:00:00 2001 From: Icenowy Zheng Date: Tue, 23 Aug 2016 21:55:46 +0800 Subject: [PATCH 17/31] ARM: dts: sun8i: add NAND controller node for A23/A33 A23/A33 has a NAND controller which can now be used properly. Add a device node for it. The DMA function cannot work because of changed DMA IP block, so it's temporarily removed in the device node. However, with PIO mode it can still work. Tested on an Aoson M751s tablet with Boris Brezillon's "mtd: nand: allow vendor specific detection/initialization" patchset, which is needed for the large-block MLC chip to be recognized correctly. ( http://lists.infradead.org/pipermail/linux-mtd/2016-June/068198.html ) Signed-off-by: Icenowy Zheng Signed-off-by: Maxime Ripard --- arch/arm/boot/dts/sun8i-a23-a33.dtsi | 21 +++++++++++++++++++++ 1 file changed, 21 insertions(+) diff --git a/arch/arm/boot/dts/sun8i-a23-a33.dtsi b/arch/arm/boot/dts/sun8i-a23-a33.dtsi index 7e05e09e61c7..6d6509c71009 100644 --- a/arch/arm/boot/dts/sun8i-a23-a33.dtsi +++ b/arch/arm/boot/dts/sun8i-a23-a33.dtsi @@ -239,6 +239,14 @@ "mmc2_sample"; }; + nand_clk: clk@01c20080 { + #clock-cells = <0>; + compatible = "allwinner,sun4i-a10-mod0-clk"; + reg = <0x01c20080 0x4>; + clocks = <&osc24M>, <&pll6 1>; + clock-output-names = "nand"; + }; + usb_clk: clk@01c200cc { #clock-cells = <1>; #reset-cells = <1>; @@ -322,6 +330,19 @@ #size-cells = <0>; }; + nfc: nand@01c03000 { + compatible = "allwinner,sun4i-a10-nand"; + reg = <0x01c03000 0x1000>; + interrupts = ; + clocks = <&ahb1_gates 13>, <&nand_clk>; + clock-names = "ahb", "mod"; + resets = <&ahb1_rst 13>; + reset-names = "ahb"; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; + }; + ehci0: usb@01c1a000 { compatible = "allwinner,sun8i-a23-ehci", "generic-ehci"; reg = <0x01c1a000 0x100>; From 1e03325af6a570ff7e6621b7eb1b3108ca67d8f9 Mon Sep 17 00:00:00 2001 From: Hans de Goede Date: Fri, 26 Aug 2016 16:52:34 +0200 Subject: [PATCH 18/31] ARM: dts: sun8i: Add dt node for esp8089 wifi chip on polaroid-mid2407 The polaroid-mid2407 tablet has an esp8089 wifi chip, add a dt node describing it. Signed-off-by: Hans de Goede Signed-off-by: Maxime Ripard --- .../dts/sun8i-a23-polaroid-mid2407pxe03.dts | 42 +++++++++++++++++++ 1 file changed, 42 insertions(+) diff --git a/arch/arm/boot/dts/sun8i-a23-polaroid-mid2407pxe03.dts b/arch/arm/boot/dts/sun8i-a23-polaroid-mid2407pxe03.dts index e3004428e7a7..4789aac89955 100644 --- a/arch/arm/boot/dts/sun8i-a23-polaroid-mid2407pxe03.dts +++ b/arch/arm/boot/dts/sun8i-a23-polaroid-mid2407pxe03.dts @@ -47,4 +47,46 @@ / { model = "Polaroid MID2407PXE03 tablet"; compatible = "polaroid,mid2407pxe03", "allwinner,sun8i-a23"; + + aliases { + ethernet0 = &esp8089; + }; + + wifi_pwrseq: wifi_pwrseq { + compatible = "mmc-pwrseq-simple"; + pinctrl-names = "default"; + pinctrl-0 = <&wifi_pwrseq_pin_mid2407>; + reset-gpios = <&r_pio 0 6 GPIO_ACTIVE_LOW>; /* PL6 */ + /* The esp8089 needs 200 ms after driving wifi-en high */ + post-power-on-delay-ms = <200>; + }; +}; + +&mmc1 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc1_pins_a>; + vmmc-supply = <®_dldo1>; + mmc-pwrseq = <&wifi_pwrseq>; + bus-width = <4>; + non-removable; + status = "okay"; + + esp8089: sdio_wifi@1 { + compatible = "esp,esp8089"; + reg = <1>; + esp,crystal-26M-en = <2>; + }; +}; + +&mmc1_pins_a { + allwinner,pull = ; +}; + +&r_pio { + wifi_pwrseq_pin_mid2407: wifi_pwrseq_pin@0 { + allwinner,pins = "PL6"; + allwinner,function = "gpio_out"; + allwinner,drive = ; + allwinner,pull = ; + }; }; From b44a0a72dfd5fc5e3194f0c8eeec5b43d33ae792 Mon Sep 17 00:00:00 2001 From: Hans de Goede Date: Fri, 26 Aug 2016 16:52:35 +0200 Subject: [PATCH 19/31] ARM: dts: sun8i: Add dt node for esp8089 wifi chip on polaroid-mid2809 The polaroid-mid2809 tablet has an esp8089 wifi chip, add a dt node describing it. Signed-off-by: Hans de Goede Signed-off-by: Maxime Ripard --- .../dts/sun8i-a23-polaroid-mid2809pxe04.dts | 42 +++++++++++++++++++ 1 file changed, 42 insertions(+) diff --git a/arch/arm/boot/dts/sun8i-a23-polaroid-mid2809pxe04.dts b/arch/arm/boot/dts/sun8i-a23-polaroid-mid2809pxe04.dts index 6d06e24d446b..c9213caf7424 100644 --- a/arch/arm/boot/dts/sun8i-a23-polaroid-mid2809pxe04.dts +++ b/arch/arm/boot/dts/sun8i-a23-polaroid-mid2809pxe04.dts @@ -47,4 +47,46 @@ / { model = "Polaroid MID2809PXE04 tablet"; compatible = "polaroid,mid2809pxe04", "allwinner,sun8i-a23"; + + aliases { + ethernet0 = &esp8089; + }; + + wifi_pwrseq: wifi_pwrseq { + compatible = "mmc-pwrseq-simple"; + pinctrl-names = "default"; + pinctrl-0 = <&wifi_pwrseq_pin_mid2809>; + reset-gpios = <&r_pio 0 6 GPIO_ACTIVE_LOW>; /* PL6 */ + /* The esp8089 needs 200 ms after driving wifi-en high */ + post-power-on-delay-ms = <200>; + }; +}; + +&mmc1 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc1_pins_a>; + vmmc-supply = <®_dldo1>; + mmc-pwrseq = <&wifi_pwrseq>; + bus-width = <4>; + non-removable; + status = "okay"; + + esp8089: sdio_wifi@1 { + compatible = "esp,esp8089"; + reg = <1>; + esp,crystal-26M-en = <2>; + }; +}; + +&mmc1_pins_a { + allwinner,pull = ; +}; + +&r_pio { + wifi_pwrseq_pin_mid2809: wifi_pwrseq_pin@0 { + allwinner,pins = "PL6"; + allwinner,function = "gpio_out"; + allwinner,drive = ; + allwinner,pull = ; + }; }; From 593d5f3a4a25da1f2d974d7ed5f92cd4fe0c8a36 Mon Sep 17 00:00:00 2001 From: Hans de Goede Date: Fri, 26 Aug 2016 16:42:23 +0200 Subject: [PATCH 20/31] ARM: dts: sun4i: Disable ohci1 on ba10-tv-box The ehci1/ohci1 pair on the ba10-tv-box is connected to an USB-2 wifi module soldered on the PCB, so there enabling ohci1 is not necessary. Signed-off-by: Hans de Goede Signed-off-by: Maxime Ripard --- arch/arm/boot/dts/sun4i-a10-ba10-tvbox.dts | 4 ---- 1 file changed, 4 deletions(-) diff --git a/arch/arm/boot/dts/sun4i-a10-ba10-tvbox.dts b/arch/arm/boot/dts/sun4i-a10-ba10-tvbox.dts index f3cb297fd1db..5f98582232d6 100644 --- a/arch/arm/boot/dts/sun4i-a10-ba10-tvbox.dts +++ b/arch/arm/boot/dts/sun4i-a10-ba10-tvbox.dts @@ -121,10 +121,6 @@ status = "okay"; }; -&ohci1 { - status = "okay"; -}; - &otg_sram { status = "okay"; }; From 1b09d23d30222988b7871293e36074a87b21ab6b Mon Sep 17 00:00:00 2001 From: Hans de Goede Date: Fri, 26 Aug 2016 16:42:24 +0200 Subject: [PATCH 21/31] ARM: dts: sun5i: Convert inet-98v-rev2 dts to use reference-design-tablet.dtsi This results in a nice cleanup :) Signed-off-by: Hans de Goede Signed-off-by: Maxime Ripard --- arch/arm/boot/dts/sun5i-a13-inet-98v-rev2.dts | 164 +----------------- 1 file changed, 1 insertion(+), 163 deletions(-) diff --git a/arch/arm/boot/dts/sun5i-a13-inet-98v-rev2.dts b/arch/arm/boot/dts/sun5i-a13-inet-98v-rev2.dts index 1b11ec95ae53..439ae3b537df 100644 --- a/arch/arm/boot/dts/sun5i-a13-inet-98v-rev2.dts +++ b/arch/arm/boot/dts/sun5i-a13-inet-98v-rev2.dts @@ -42,171 +42,9 @@ /dts-v1/; #include "sun5i-a13.dtsi" -#include "sunxi-common-regulators.dtsi" -#include -#include -#include -#include +#include "sun5i-reference-design-tablet.dtsi" / { model = "INet-98V Rev 02"; compatible = "primux,inet98v-rev2", "allwinner,sun5i-a13"; - - aliases { - serial0 = &uart1; - }; - - chosen { - stdout-path = "serial0:115200n8"; - }; - -}; - -&cpu0 { - cpu-supply = <®_dcdc2>; -}; - -&ehci0 { - status = "okay"; -}; - -&i2c0 { - pinctrl-names = "default"; - pinctrl-0 = <&i2c0_pins_a>; - status = "okay"; - - axp209: pmic@34 { - reg = <0x34>; - interrupts = <0>; - }; -}; - -#include "axp209.dtsi" - -&i2c1 { - pinctrl-names = "default"; - pinctrl-0 = <&i2c1_pins_a>; - status = "okay"; - - pcf8563: rtc@51 { - compatible = "nxp,pcf8563"; - reg = <0x51>; - }; -}; - -&lradc { - vref-supply = <®_ldo2>; - status = "okay"; - - button@200 { - label = "Volume Up"; - linux,code = ; - channel = <0>; - voltage = <200000>; - }; - - button@400 { - label = "Volume Down"; - linux,code = ; - channel = <0>; - voltage = <400000>; - }; -}; - -&mmc0 { - pinctrl-names = "default"; - pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_inet98fv2>; - vmmc-supply = <®_vcc3v3>; - bus-width = <4>; - cd-gpios = <&pio 6 0 GPIO_ACTIVE_HIGH>; /* PG0 */ - cd-inverted; - status = "okay"; -}; - -&otg_sram { - status = "okay"; -}; - -&pio { - mmc0_cd_pin_inet98fv2: mmc0_cd_pin@0 { - allwinner,pins = "PG0"; - allwinner,function = "gpio_in"; - allwinner,drive = ; - allwinner,pull = ; - }; - - usb0_vbus_detect_pin: usb0_vbus_detect_pin@0 { - allwinner,pins = "PG1"; - allwinner,function = "gpio_in"; - allwinner,drive = ; - allwinner,pull = ; - }; - - usb0_id_detect_pin: usb0_id_detect_pin@0 { - allwinner,pins = "PG2"; - allwinner,function = "gpio_in"; - allwinner,drive = ; - allwinner,pull = ; - }; -}; - -®_dcdc2 { - regulator-always-on; - regulator-min-microvolt = <1000000>; - regulator-max-microvolt = <1400000>; - regulator-name = "vdd-cpu"; -}; - -®_dcdc3 { - regulator-always-on; - regulator-min-microvolt = <1250000>; - regulator-max-microvolt = <1250000>; - regulator-name = "vdd-int-pll"; -}; - -®_ldo1 { - regulator-name = "vdd-rtc"; -}; - -®_ldo2 { - regulator-always-on; - regulator-min-microvolt = <3000000>; - regulator-max-microvolt = <3000000>; - regulator-name = "avcc"; -}; - -®_ldo3 { - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - regulator-name = "vcc-wifi"; -}; - -®_usb0_vbus { - gpio = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */ - status = "okay"; -}; - -&uart1 { - pinctrl-names = "default"; - pinctrl-0 = <&uart1_pins_b>; - status = "okay"; -}; - -&usb_otg { - dr_mode = "otg"; - status = "okay"; -}; - -&usb0_vbus_pin_a { - allwinner,pins = "PG12"; -}; - -&usbphy { - pinctrl-names = "default"; - pinctrl-0 = <&usb0_id_detect_pin>, <&usb0_vbus_detect_pin>; - usb0_id_det-gpio = <&pio 6 2 GPIO_ACTIVE_HIGH>; /* PG2 */ - usb0_vbus_det-gpio = <&pio 6 1 GPIO_ACTIVE_HIGH>; /* PG1 */ - usb0_vbus-supply = <®_usb0_vbus>; - usb1_vbus-supply = <®_ldo3>; - status = "okay"; }; From cb0db11afe72eb5206ba35cd9afa2868d0550cbe Mon Sep 17 00:00:00 2001 From: Hans de Goede Date: Fri, 26 Aug 2016 16:42:25 +0200 Subject: [PATCH 22/31] ARM: dts: sun5i: Add dts file for the Empire Electronix M712 tablet Add a dts file for the Empire Electronix M712 tablet, this is a 7" A13 tablet, with micro-usb (otg), headphone and micro-sd slots on the outside. It uses a Goodix gt811 touchscreen controller, a RTL8188CTV wifi chip and a DMART06 (1238a4) accelerometer. Note currently the dts for this is somewhat empty. This will change once we add support for the touchscreen and accelerometer. Signed-off-by: Hans de Goede Signed-off-by: Maxime Ripard --- arch/arm/boot/dts/Makefile | 1 + .../dts/sun5i-a13-empire-electronix-m712.dts | 51 +++++++++++++++++++ 2 files changed, 52 insertions(+) create mode 100644 arch/arm/boot/dts/sun5i-a13-empire-electronix-m712.dts diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 1ec7fe99de33..94d5591188b1 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -727,6 +727,7 @@ dtb-$(CONFIG_MACH_SUN5I) += \ sun5i-a10s-wobo-i5.dtb \ sun5i-a13-difrnce-dit4350.dtb \ sun5i-a13-empire-electronix-d709.dtb \ + sun5i-a13-empire-electronix-m712.dtb \ sun5i-a13-hsg-h702.dtb \ sun5i-a13-inet-98v-rev2.dtb \ sun5i-a13-olinuxino.dtb \ diff --git a/arch/arm/boot/dts/sun5i-a13-empire-electronix-m712.dts b/arch/arm/boot/dts/sun5i-a13-empire-electronix-m712.dts new file mode 100644 index 000000000000..b1e2afd9de52 --- /dev/null +++ b/arch/arm/boot/dts/sun5i-a13-empire-electronix-m712.dts @@ -0,0 +1,51 @@ +/* + * Copyright 2016 Hans de Goede + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; +#include "sun5i-a13.dtsi" +#include "sun5i-reference-design-tablet.dtsi" +#include + +/ { + model = "Empire Electronix M712 tablet"; + compatible = "empire-electronix,m712", "allwinner,sun5i-a13"; +}; From c224d20db77b944a7aed1c4f8723508ee409af48 Mon Sep 17 00:00:00 2001 From: Hans de Goede Date: Fri, 26 Aug 2016 16:42:26 +0200 Subject: [PATCH 23/31] ARM: dts: sun8i: Rename reference-design-tablet touchscreen node Rename the reference-design-tablet touchscreen node from gsl1680 to touchscreen, all? tablets seem to use the same power and interrupt gpio-s, but not all tablets use a gsl1680 controller making the gsl1680 name somewhat misleading. Also move the reg and compatible property to the actual tablet dts as they may differ per tablet. Signed-off-by: Hans de Goede Signed-off-by: Maxime Ripard --- arch/arm/boot/dts/sun8i-reference-design-tablet.dtsi | 6 ++---- 1 file changed, 2 insertions(+), 4 deletions(-) diff --git a/arch/arm/boot/dts/sun8i-reference-design-tablet.dtsi b/arch/arm/boot/dts/sun8i-reference-design-tablet.dtsi index f29897c40ae8..08cd00143635 100644 --- a/arch/arm/boot/dts/sun8i-reference-design-tablet.dtsi +++ b/arch/arm/boot/dts/sun8i-reference-design-tablet.dtsi @@ -71,15 +71,13 @@ */ clock-frequency = <400000>; - gsl1680: touchscreen@40 { - compatible = "silead,gsl1680"; - reg = <0x40>; + touchscreen: touchscreen@0 { interrupt-parent = <&pio>; interrupts = <1 5 IRQ_TYPE_EDGE_FALLING>; /* PB5 */ pinctrl-names = "default"; pinctrl-0 = <&ts_power_pin>; power-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */ - /* Most tablets use this touchscreen, but not all */ + /* Tablet dts must provide reg and compatible */ status = "disabled"; }; }; From 06ad11be7a9e13499ff8e55e46f09d22f9ee6fc0 Mon Sep 17 00:00:00 2001 From: Chen-Yu Tsai Date: Sat, 27 Aug 2016 15:59:50 +0800 Subject: [PATCH 24/31] ARM: dts: sun9i: Add missing #interrupt-cells to R_PIO pinctrl device node The R_PIO device node is missing #interrupt-cells, which causes interrupt parsing to fail to match it as a valid interrupt controller. Add #interrupt-cells to it. Also remove the unnecesary #address-cells and #size-cells. Fixes: 1ac56a6da9e1 ("ARM: dts: sun9i: Add A80 R_PIO pin controller device node") Signed-off-by: Chen-Yu Tsai Signed-off-by: Maxime Ripard --- arch/arm/boot/dts/sun9i-a80.dtsi | 3 +-- 1 file changed, 1 insertion(+), 2 deletions(-) diff --git a/arch/arm/boot/dts/sun9i-a80.dtsi b/arch/arm/boot/dts/sun9i-a80.dtsi index 24e3cac4f571..3c5214cbe4e6 100644 --- a/arch/arm/boot/dts/sun9i-a80.dtsi +++ b/arch/arm/boot/dts/sun9i-a80.dtsi @@ -898,8 +898,7 @@ resets = <&apbs_rst 0>; gpio-controller; interrupt-controller; - #address-cells = <1>; - #size-cells = <0>; + #interrupt-cells = <3>; #gpio-cells = <3>; r_ir_pins: r_ir { From 01f222dfcf7f301035ed104029bc51710d4ce4e5 Mon Sep 17 00:00:00 2001 From: Icenowy Zheng Date: Fri, 26 Aug 2016 18:23:56 +0800 Subject: [PATCH 25/31] ARM: dts: sun8i: Add dts file for inet-d978_rev2 tablets The inet-d978_rev2 is a pcb used in generic A33 based tablets. It features volume buttons, micro-usb otg, headphone connector and a power button. On the board a Realtek RTL8723BS SDIO Wi-Fi module are soldered, and there is also a accompanied board which has a Goodix GT9271 soldered. As this board is desired to create tablets with a Home key dealed by GT9271, a LED is present at the front panel at the position of the Home key. Signed-off-by: Icenowy Zheng Signed-off-by: Maxime Ripard --- arch/arm/boot/dts/Makefile | 1 + .../arm/boot/dts/sun8i-a33-inet-d978-rev2.dts | 88 +++++++++++++++++++ 2 files changed, 89 insertions(+) create mode 100644 arch/arm/boot/dts/sun8i-a33-inet-d978-rev2.dts diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 94d5591188b1..7dd4a07c4784 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -784,6 +784,7 @@ dtb-$(CONFIG_MACH_SUN8I) += \ sun8i-a23-q8-tablet.dtb \ sun8i-a33-et-q8-v1.6.dtb \ sun8i-a33-ga10h-v1.1.dtb \ + sun8i-a33-inet-d978-rev2.dtb \ sun8i-a33-ippo-q8h-v1.2.dtb \ sun8i-a33-olinuxino.dtb \ sun8i-a33-q8-tablet.dtb \ diff --git a/arch/arm/boot/dts/sun8i-a33-inet-d978-rev2.dts b/arch/arm/boot/dts/sun8i-a33-inet-d978-rev2.dts new file mode 100644 index 000000000000..0f52cd9dfa41 --- /dev/null +++ b/arch/arm/boot/dts/sun8i-a33-inet-d978-rev2.dts @@ -0,0 +1,88 @@ +/* + * Copyright 2015 Hans de Goede + * Copyright 2016 Icenowy Zheng + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; +#include "sun8i-a33.dtsi" +#include "sun8i-reference-design-tablet.dtsi" + +/ { + model = "INet-D978 Rev 02"; + compatible = "primux,inet-d978-rev2", "allwinner,sun8i-a33"; + + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&led_pin_d978>; + + home { + label = "d978:blue:home"; + gpios = <&r_pio 0 5 GPIO_ACTIVE_HIGH>; /* PL5 */ + }; + }; +}; + +&mmc1_pins_a { + allwinner,pull = ; +}; + +&mmc1 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc1_pins_a>; + vmmc-supply = <®_dldo1>; + bus-width = <4>; + non-removable; + status = "okay"; + + rtl8723bs: sdio_wifi@1 { + reg = <1>; + }; +}; + +&r_pio { + led_pin_d978: led_pin_d978@0 { + allwinner,pins = "PL5"; + allwinner,function = "gpio_out"; + allwinner,drive = ; + allwinner,pull = ; + }; +}; From a37b7a5a86d5455d9b1dc840de1946312fa51b23 Mon Sep 17 00:00:00 2001 From: Milo Kim Date: Wed, 31 Aug 2016 17:25:18 +0900 Subject: [PATCH 26/31] ARM: dts: sun8i: Add PWM controller node in H3 Acked-by: Chen-Yu Tsai Signed-off-by: Milo Kim Signed-off-by: Maxime Ripard --- arch/arm/boot/dts/sun8i-h3.dtsi | 8 ++++++++ 1 file changed, 8 insertions(+) diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/sun8i-h3.dtsi index fdf9fdbda267..6d83b8674201 100644 --- a/arch/arm/boot/dts/sun8i-h3.dtsi +++ b/arch/arm/boot/dts/sun8i-h3.dtsi @@ -389,6 +389,14 @@ interrupts = ; }; + pwm: pwm@01c21400 { + compatible = "allwinner,sun8i-h3-pwm"; + reg = <0x01c21400 0x8>; + clocks = <&osc24M>; + #pwm-cells = <3>; + status = "disabled"; + }; + uart0: serial@01c28000 { compatible = "snps,dw-apb-uart"; reg = <0x01c28000 0x400>; From 19635b0c13a0eb3bc6f5352134b8b4846ab88afe Mon Sep 17 00:00:00 2001 From: Hans de Goede Date: Sat, 3 Sep 2016 13:05:17 +0200 Subject: [PATCH 27/31] ARM: dts: sun8i: Orange Pi Plus dts is for the Plus and Plus 2 Update the sun8i-h3-orangepi-plus.dts model string to reflect that it is valid for both the Orange Pi Plus and the Orange Pi Plus 2. This is also meant to help users realize that it is not valid for the new Orange Pi Plus 2E, which will get its own dts. Signed-off-by: Hans de Goede Signed-off-by: Maxime Ripard --- arch/arm/boot/dts/sun8i-h3-orangepi-plus.dts | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-plus.dts b/arch/arm/boot/dts/sun8i-h3-orangepi-plus.dts index b0cb41787e09..bb585918cf54 100644 --- a/arch/arm/boot/dts/sun8i-h3-orangepi-plus.dts +++ b/arch/arm/boot/dts/sun8i-h3-orangepi-plus.dts @@ -44,7 +44,7 @@ #include "sun8i-h3-orangepi-2.dts" / { - model = "Xunlong Orange Pi Plus"; + model = "Xunlong Orange Pi Plus / Plus 2"; compatible = "xunlong,orangepi-plus", "allwinner,sun8i-h3"; reg_usb3_vbus: usb3-vbus { From 2ea3c34bc2ee83d2ae9701d5194054be62a05105 Mon Sep 17 00:00:00 2001 From: Hans de Goede Date: Sat, 3 Sep 2016 13:05:18 +0200 Subject: [PATCH 28/31] ARM: dts: sun8i: Add dts file for the Orange Pi Plus2E SBC The Orange Pi Plus2E is an extended version of the Orange Pi Pc Plus, with 2G RAM and an external gbit ethernet phy. Note currently the dts is pretty much empty (except for including the pc-plus dts), I've a local patch which enables the emac actually making this dts different from the pc-plus one, but that needs the h3 emac driver to get merged first. Signed-off-by: Hans de Goede Signed-off-by: Maxime Ripard --- arch/arm/boot/dts/Makefile | 1 + .../arm/boot/dts/sun8i-h3-orangepi-plus2e.dts | 53 +++++++++++++++++++ 2 files changed, 54 insertions(+) create mode 100644 arch/arm/boot/dts/sun8i-h3-orangepi-plus2e.dts diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 7dd4a07c4784..bb906f23d161 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -798,6 +798,7 @@ dtb-$(CONFIG_MACH_SUN8I) += \ sun8i-h3-orangepi-pc.dtb \ sun8i-h3-orangepi-pc-plus.dtb \ sun8i-h3-orangepi-plus.dtb \ + sun8i-h3-orangepi-plus2e.dtb \ sun8i-r16-parrot.dtb dtb-$(CONFIG_MACH_SUN9I) += \ sun9i-a80-optimus.dtb \ diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-plus2e.dts b/arch/arm/boot/dts/sun8i-h3-orangepi-plus2e.dts new file mode 100644 index 000000000000..5851a47a3089 --- /dev/null +++ b/arch/arm/boot/dts/sun8i-h3-orangepi-plus2e.dts @@ -0,0 +1,53 @@ +/* + * Copyright (C) 2016 Hans de Goede + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/* + * The Orange Pi Plus 2E is an extended version of the Orange Pi PC Plus, + * with 2G RAM and an external gbit ethernet phy. + */ + +#include "sun8i-h3-orangepi-pc-plus.dts" + +/ { + model = "Xunlong Orange Pi Plus 2E"; + compatible = "xunlong,orangepi-plus2e", "allwinner,sun8i-h3"; +}; From 621efefc9b3135408de818c01528bc3adacd557c Mon Sep 17 00:00:00 2001 From: Hans de Goede Date: Fri, 26 Aug 2016 16:52:36 +0200 Subject: [PATCH 29/31] ARM: dts: sun8i-q8-common: Add support for SDIO wifi controllers Most of the sun8i q8 boards have an SDIO wifi controller, on the variants which use an USB wifi controller, this will result in a couple of error msg-s in dmesg when proving the sdio bus and an used mmc controller. The best way to deal with wifi on this boards really is to simply let the kernel auto-detect usb or sdio wifi controllers, so we will just have to live with the few errors in dmesg. This has been tested on a23 based q8 tablets with ESP8089, RTL8703AS and RTL8189FTV wifi controllers. Signed-off-by: Hans de Goede Signed-off-by: Maxime Ripard --- arch/arm/boot/dts/sun8i-q8-common.dtsi | 49 ++++++++++++++++++++++++++ 1 file changed, 49 insertions(+) diff --git a/arch/arm/boot/dts/sun8i-q8-common.dtsi b/arch/arm/boot/dts/sun8i-q8-common.dtsi index 60fa9585022b..29f837a47771 100644 --- a/arch/arm/boot/dts/sun8i-q8-common.dtsi +++ b/arch/arm/boot/dts/sun8i-q8-common.dtsi @@ -42,10 +42,59 @@ #include "sunxi-reference-design-tablet.dtsi" #include "sun8i-reference-design-tablet.dtsi" +/ { + aliases { + serial0 = &r_uart; + /* Make u-boot set mac-address for wifi without an eeprom */ + ethernet0 = &sdio_wifi; + }; + + wifi_pwrseq: wifi_pwrseq { + compatible = "mmc-pwrseq-simple"; + /* + * Q8 boards use various PL# pins as wifi-en. On other boards + * these may be connected to a wifi module output pin. To avoid + * short-circuits we configure these as inputs with pull-ups via + * pinctrl, instead of listing them as active-low reset-gpios. + */ + pinctrl-names = "default"; + pinctrl-0 = <&wifi_pwrseq_pin_q8>; + /* The esp8089 needs 200 ms after driving wifi-en high */ + post-power-on-delay-ms = <200>; + }; +}; + &ehci0 { status = "okay"; }; +&mmc1 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc1_pins_a>; + vmmc-supply = <®_dldo1>; + mmc-pwrseq = <&wifi_pwrseq>; + bus-width = <4>; + non-removable; + status = "okay"; + + sdio_wifi: sdio_wifi@1 { + reg = <1>; + }; +}; + +&mmc1_pins_a { + allwinner,pull = ; +}; + +&r_pio { + wifi_pwrseq_pin_q8: wifi_pwrseq_pin@0 { + allwinner,pins = "PL6", "PL7", "PL11"; + allwinner,function = "gpio_in"; + allwinner,drive = ; + allwinner,pull = ; + }; +}; + &usbphy { usb1_vbus-supply = <®_dldo1>; }; From 6d2ce1c01cc6a6506e7206d58ffed2aa4caed5e7 Mon Sep 17 00:00:00 2001 From: James Pettigrew Date: Tue, 6 Sep 2016 08:15:56 +1000 Subject: [PATCH 30/31] ARM: dts: sun8i: Add dts file for the NanoPi NEO SBC The NanoPi NEO is a minimal H3 based SBC. It comes with 256/512M RAM, a micro SD slot, 10/100Mbit ethernet and a single USB-A port. Signed-off-by: James Pettigrew Reviewed-by: Rask Ingemann Lambertsen Signed-off-by: Maxime Ripard --- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/sun8i-h3-nanopi-neo.dts | 125 ++++++++++++++++++++++ 2 files changed, 126 insertions(+) create mode 100644 arch/arm/boot/dts/sun8i-h3-nanopi-neo.dts diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index bb906f23d161..d5b7d9003bd2 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -792,6 +792,7 @@ dtb-$(CONFIG_MACH_SUN8I) += \ sun8i-a83t-allwinner-h8homlet-v2.dtb \ sun8i-a83t-cubietruck-plus.dtb \ sun8i-h3-bananapi-m2-plus.dtb \ + sun8i-h3-nanopi-neo.dtb \ sun8i-h3-orangepi-2.dtb \ sun8i-h3-orangepi-lite.dtb \ sun8i-h3-orangepi-one.dtb \ diff --git a/arch/arm/boot/dts/sun8i-h3-nanopi-neo.dts b/arch/arm/boot/dts/sun8i-h3-nanopi-neo.dts new file mode 100644 index 000000000000..3d64cafc1e90 --- /dev/null +++ b/arch/arm/boot/dts/sun8i-h3-nanopi-neo.dts @@ -0,0 +1,125 @@ +/* + * Copyright (C) 2016 James Pettigrew + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; +#include "sun8i-h3.dtsi" +#include "sunxi-common-regulators.dtsi" + +#include +#include + +/ { + model = "FriendlyARM NanoPi NEO"; + compatible = "friendlyarm,nanopi-neo", "allwinner,sun8i-h3"; + + aliases { + serial0 = &uart0; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&leds_opc>, <&leds_r_opc>; + + pwr { + label = "nanopi:green:pwr"; + gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; /* PL10 */ + default-state = "on"; + }; + + status { + label = "nanopi:blue:status"; + gpios = <&pio 0 10 GPIO_ACTIVE_HIGH>; /* PA10 */ + }; + }; +}; + +&ehci3 { + status = "okay"; +}; + +&mmc0 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>; + vmmc-supply = <®_vcc3v3>; + bus-width = <4>; + cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */ + cd-inverted; + status = "okay"; +}; + +&ohci3 { + status = "okay"; +}; + +&pio { + leds_opc: led-pins { + allwinner,pins = "PA10"; + allwinner,function = "gpio_out"; + allwinner,drive = ; + allwinner,pull = ; + }; +}; + +&r_pio { + leds_r_opc: led-pins { + allwinner,pins = "PL10"; + allwinner,function = "gpio_out"; + allwinner,drive = ; + allwinner,pull = ; + }; +}; + +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_pins_a>; + status = "okay"; +}; + +&usbphy { + /* USB VBUS is always on */ + status = "okay"; +}; From accfb2f19d185628858dc0c063c69c8b75b32724 Mon Sep 17 00:00:00 2001 From: James Pettigrew Date: Tue, 6 Sep 2016 08:15:57 +1000 Subject: [PATCH 31/31] devicetree: Add vendor prefix for FriendlyARM Guangzhou FriendlyARM Computer Tech Co., Ltd is a Chinese ARM board vendor. Signed-off-by: James Pettigrew Reviewed-by: Rask Ingemann Lambertsen Acked-by: Chen-Yu Tsai Signed-off-by: Maxime Ripard --- Documentation/devicetree/bindings/vendor-prefixes.txt | 1 + 1 file changed, 1 insertion(+) diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index 1992aa97d45a..7b6bda3b4189 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -98,6 +98,7 @@ ezchip EZchip Semiconductor fcs Fairchild Semiconductor firefly Firefly focaltech FocalTech Systems Co.,Ltd +friendlyarm Guangzhou FriendlyARM Computer Tech Co., Ltd fsl Freescale Semiconductor ge General Electric Company geekbuying GeekBuying