USB: Disable hub-initiated LPM for comms devices.

Hub-initiated LPM is not good for USB communications devices.  Comms
devices should be able to tell when their link can go into a lower power
state, because they know when an incoming transmission is finished.
Ideally, these devices would slam their links into a lower power state,
using the device-initiated LPM, after finishing the last packet of their
data transfer.

If we enable the idle timeouts for the parent hubs to enable
hub-initiated LPM, we will get a lot of useless LPM packets on the bus
as the devices reject LPM transitions when they're in the middle of
receiving data.  Worse, some devices might blindly accept the
hub-initiated LPM and power down their radios while they're in the
middle of receiving a transmission.

The Intel Windows folks are disabling hub-initiated LPM for all USB
communications devices under a xHCI USB 3.0 host.  In order to keep
the Linux behavior as close as possible to Windows, we need to do the
same in Linux.

Set the disable_hub_initiated_lpm flag for for all USB communications
drivers.  I know there aren't currently any USB 3.0 devices that
implement these class specifications, but we should be ready if they do.

Signed-off-by: Sarah Sharp <[email protected]>
Cc: Marcel Holtmann <[email protected]>
Cc: Gustavo Padovan <[email protected]>
Cc: Johan Hedberg <[email protected]>
Cc: Hansjoerg Lipp <[email protected]>
Cc: Tilman Schmidt <[email protected]>
Cc: Karsten Keil <[email protected]>
Cc: Peter Korsgaard <[email protected]>
Cc: Jan Dumon <[email protected]>
Cc: Petko Manolov <[email protected]>
Cc: Steve Glendinning <[email protected]>
Cc: "John W. Linville" <[email protected]>
Cc: Kalle Valo <[email protected]>
Cc: "Luis R. Rodriguez" <[email protected]>
Cc: Jouni Malinen <[email protected]>
Cc: Vasanthakumar Thiagarajan <[email protected]>
Cc: Senthil Balasubramanian <[email protected]>
Cc: Christian Lamparter <[email protected]>
Cc: Brett Rudley <[email protected]>
Cc: Roland Vossen <[email protected]>
Cc: Arend van Spriel <[email protected]>
Cc: "Franky (Zhenhui) Lin" <[email protected]>
Cc: Kan Yan <[email protected]>
Cc: Dan Williams <[email protected]>
Cc: Jussi Kivilinna <[email protected]>
Cc: Ivo van Doorn <[email protected]>
Cc: Gertjan van Wingerde <[email protected]>
Cc: Helmut Schaa <[email protected]>
Cc: Herton Ronaldo Krzesinski <[email protected]>
Cc: Hin-Tak Leung <[email protected]>
Cc: Larry Finger <[email protected]>
Cc: Chaoming Li <[email protected]>
Cc: Daniel Drake <[email protected]>
Cc: Ulrich Kunitz <[email protected]>
Signed-off-by: Sarah Sharp <[email protected]>

drivers/bluetooth/ath3k.c

@@ -439,6 +439,7 @@ static struct usb_driver ath3k_driver = {
 	.probe		= ath3k_probe,
 	.disconnect	= ath3k_disconnect,
 	.id_table	= ath3k_table,
+	.disable_hub_initiated_lpm = 1,
 };
 
 module_usb_driver(ath3k_driver);

drivers/bluetooth/bcm203x.c

@@ -279,6 +279,7 @@ static struct usb_driver bcm203x_driver = {
 	.probe		= bcm203x_probe,
 	.disconnect	= bcm203x_disconnect,
 	.id_table	= bcm203x_table,
+	.disable_hub_initiated_lpm = 1,
 };
 
 module_usb_driver(bcm203x_driver);

drivers/bluetooth/bfusb.c

@@ -749,6 +749,7 @@ static struct usb_driver bfusb_driver = {
 	.probe		= bfusb_probe,
 	.disconnect	= bfusb_disconnect,
 	.id_table	= bfusb_table,
+	.disable_hub_initiated_lpm = 1,
 };
 
 module_usb_driver(bfusb_driver);

drivers/bluetooth/bpa10x.c

@@ -508,6 +508,7 @@ static struct usb_driver bpa10x_driver = {
 	.probe		= bpa10x_probe,
 	.disconnect	= bpa10x_disconnect,
 	.id_table	= bpa10x_table,
+	.disable_hub_initiated_lpm = 1,
 };
 
 module_usb_driver(bpa10x_driver);

drivers/bluetooth/btusb.c

@@ -1218,6 +1218,7 @@ static struct usb_driver btusb_driver = {
 #endif
 	.id_table	= btusb_table,
 	.supports_autosuspend = 1,
+	.disable_hub_initiated_lpm = 1,
 };
 
 module_usb_driver(btusb_driver);