diff --git a/bindings/input/qpnp-power-on.txt b/bindings/input/qpnp-power-on.txt new file mode 100644 index 000000000000..d935a2a443d3 --- /dev/null +++ b/bindings/input/qpnp-power-on.txt @@ -0,0 +1,247 @@ +Qualcomm Technologies, Inc. QPNP Power-on PMIC Peripheral Device Tree Bindings + +qpnp-power-on devices support the power-on (PON) peripheral found on +Qualcomm Technologies, Inc. PMICs. The supported functionality includes power +on/off reason, key press/release detection, PMIC reset configurations and other +PON specific features. The PON module supports multiple physical power-on +(KPDPWR_N, CBLPWR) and reset (KPDPWR_N, RESIN, KPDPWR+RESIN) sources. This +peripheral is connected to the host processor via the SPMI interface. + +Required properties: +- compatible: Must be "qcom,qpnp-power-on" +- reg: Specifies the SPMI base address for this PON + (power-on) peripheral. + +Optional properties: +- interrupts: Specifies the interrupts associated with PON. +- interrupt-names: Specifies the interrupt names associated with + the interrupts property. Must be a subset of + "kpdpwr", "kpdpwr-bark", "resin", "resin-bark", + "cblpwr", "kpdpwr-resin-bark", and + "pmic-wd-bark". Bark interrupts are associated + with system reset configuration to allow default + reset configuration to be activated. If system + reset configuration is not supported then bark + interrupts are nops. Additionally, the + "pmic-wd-bark" interrupt can be added if the + system needs to handle PMIC watchdog barks. +- qcom,pon-dbc-delay: The debounce delay for the power-key interrupt + specified in us. + Possible values for GEN1 PON are: + 15625, 31250, 62500, 125000, 250000, 500000, + 1000000 and 2000000. + Possible values for GEN2 PON are: + 62, 123, 245, 489, 977, 1954, 3907, 7813, + 15625, 31250, 62500, 125000 and 250000. + Intermediate value is rounded down to the + nearest valid value. +- qcom,system-reset: Boolean which specifies that this PON peripheral + can be used to reset the system. This property + can only be used by one device on the system. It + is an error to include it more than once. +- qcom,modem-reset: Boolean which specifies that this PON peripheral + can be used to reset the attached modem chip. + This property can only be used by one PON device + on the system. qcom,modem-reset and + qcom,system-reset cannot be specified for the + same PON device. +- qcom,s3-debounce: The debounce delay for stage 3 reset trigger in + secs. The values range from 0 to 128. +- qcom,s3-src: The source for stage 3 reset. It can be one of + "kpdpwr", "resin", "kpdpwr-or-resin" or + "kpdpwr-and-resin". +- qcom,uvlo-panic: Boolean indicating that the device should + trigger a controlled panic shutdown if a restart + was caused by under voltage lock-out (UVLO). +- qcom,clear-warm-reset: Boolean which specifies that the WARM_RESET + reason registers need to be cleared for this + target. The property is used for the targets + which have a hardware feature to catch resets + which aren't triggered by the application + processor. In such cases clearing WARM_REASON + registers across processor resets keeps the + registers in a useful state. +- qcom,secondary-pon-reset: Boolean property which indicates that the PON + peripheral is a secondary PON device which + needs to be configured during reset in addition + to the primary PON device that is configured + for system reset through qcom,system-reset + property. + This should not be defined along with the + qcom,system-reset or qcom,modem-reset property. +- qcom,store-hard-reset-reason: Boolean property which if set will store the + hardware reset reason to SOFT_RB_SPARE register + of the core PMIC PON peripheral. +- qcom,warm-reset-poweroff-type: Poweroff type required to be configured + on PS_HOLD reset control register when the + system goes for warm reset. If this property is + not specified, then the default type, warm reset + will be configured to PS_HOLD reset control + register. + Supported values: PON_POWER_OFF_TYPE_* found in + include/dt-bindings/input/qcom,qpnp-power-on.h +- qcom,hard-reset-poweroff-type: Same description as + qcom,warm-reset-poweroff-type but this applies + for the system hard reset case. +- qcom,shutdown-poweroff-type: Same description as qcom,warm-reset-poweroff- + type but this applies for the system shutdown + case. +- qcom,kpdpwr-sw-debounce: Boolean property to enable the debounce logic + on the KPDPWR_N rising edge. +- qcom,resin-pon-reset: Boolean property which indicates that resin + needs to be configured during reset in addition + to the primary PON device that is configured + for system reset through qcom,system-reset + property. +- qcom,resin-warm-reset-type: Poweroff type required to be configured on + RESIN reset control register when the system + initiates warm reset. If this property is not + specified, then the default type, warm reset + will be configured to RESIN reset control + register. This property is effective only if + qcom,resin-pon-reset is defined. + Supported values: PON_POWER_OFF_TYPE_* found in + include/dt-bindings/input/qcom,qpnp-power-on.h +- qcom,resin-hard-reset-type: Same description as qcom,resin-warm-reset-type + but this applies for the system hard reset case. +- qcom,resin-shutdown-type: Same description as qcom,resin-warm-reset-type + but this applies for the system shutdown case. +- qcom,resin-shutdown-disable: Boolean property to disable RESIN power off + trigger during system shutdown case. + This property is effective only if + qcom,resin-pon-reset is defined. +- qcom,resin-hard-reset-disable: Boolean property to disable RESIN power + off trigger during system hard reset case. + This property is effective only if + qcom,resin-pon-reset is defined. +- qcom,ps-hold-shutdown-disable: Boolean property to disable PS_HOLD + power off trigger during system shutdown case. +- qcom,ps-hold-hard-reset-disable: Boolean property to disable PS_HOLD + power off trigger during system hard reset case. + +Optional Sub-nodes: +- qcom,pon_1 ... qcom,pon_n: These PON child nodes correspond to features + supported by the PON peripheral including reset + configurations, pushbutton keys, and regulators. + +Sub-node properties: + +Sub-nodes (if defined) should belong to either a PON configuration or a +regulator configuration. + +Regulator sub-node required properties: +- regulator-name: Regulator name for the PON regulator that is + being configured. +- qcom,pon-spare-reg-addr: Register offset from the base address of the + PON peripheral that needs to be configured for + the regulator being controlled. +- qcom,pon-spare-reg-bit: Bit position in the specified register that + needs to be configured for the regulator being + controlled. + +PON sub-node required properties: +- qcom,pon-type: The type of PON/RESET source. Supported values: + 0 = KPDPWR + 1 = RESIN + 2 = CBLPWR + 3 = KPDPWR_RESIN + These values are PON_POWER_ON_TYPE_* found in + include/dt-bindings/input/qcom,qpnp-power-on.h + +PON sub-node optional properties: +- qcom,pull-up: Boolean flag indicating if a pull-up resistor + should be enabled for the input. +- qcom,support-reset: Indicates if this PON source supports + reset functionality. + 0 = Not supported + 1 = Supported + If this property is not defined, then default S2 + reset configurations should not be modified. +- qcom,use-bark: Specify if this PON type needs to handle a bark + interrupt. +- linux,code: The input key-code associated with the reset + source. The reset source in its default + configuration can be used to support standard + keys. + +The below mentioned properties are required only when qcom,support-reset DT +property is defined and is set to 1. + +- qcom,s1-timer: The debounce timer for the BARK interrupt for + the reset source. Value is specified in ms. + Supported values are: + 0, 32, 56, 80, 128, 184, 272, 408, 608, 904, + 1352, 2048, 3072, 4480, 6720, 10256 +- qcom,s2-timer: The debounce timer for the S2 reset specified + in ms. On the expiry of this timer, the PMIC + executes the reset sequence. + Supported values are: + 0, 10, 50, 100, 250, 500, 1000, 2000 +- qcom,s2-type: The type of reset associated with this source. + Supported values: + 0 = SOFT_RESET (legacy) + 1 = WARM_RESET + 4 = SHUTDOWN + 5 = DVDD_SHUTDOWN + 7 = HARD_RESET + 8 = DVDD_HARD_RESET + These values are PON_POWER_OFF_TYPE_* found in + include/dt-bindings/input/qcom,qpnp-power-on.h + +Examples: + qcom,power-on@800 { + compatible = "qcom,qpnp-power-on"; + reg = <0x800>; + interrupts = <0x0 0x8 0x0 IRQ_TYPE_EDGE_BOTH>, + <0x0 0x8 0x1 IRQ_TYPE_EDGE_BOTH>, + <0x0 0x8 0x4 IRQ_TYPE_EDGE_RISING>, + <0x0 0x8 0x5 IRQ_TYPE_EDGE_RISING>; + interrupt-names = "kpdpwr", "resin", "resin-bark", + "kpdpwr-resin-bark"; + qcom,pon-dbc-delay = <15625>; + qcom,system-reset; + qcom,s3-debounce = <32>; + qcom,s3-src = "resin"; + qcom,clear-warm-reset; + qcom,store-hard-reset-reason; + + qcom,pon_1 { + qcom,pon-type = ; + qcom,pull-up; + linux,code = ; + }; + + qcom,pon_2 { + qcom,pon-type = ; + qcom,support-reset = <1>; + qcom,pull-up; + qcom,s1-timer = <0>; + qcom,s2-timer = <2000>; + qcom,s2-type = ; + linux,code = ; + qcom,use-bark; + }; + + qcom,pon_3 { + qcom,pon-type = ; + qcom,support-reset = <1>; + qcom,s1-timer = <6720>; + qcom,s2-timer = <2000>; + qcom,s2-type = ; + qcom,pull-up; + qcom,use-bark; + }; + }; + + qcom,power-on@800 { + compatible = "qcom,qpnp-power-on"; + reg = <0x800>; + qcom,secondary-pon-reset; + qcom,hard-reset-poweroff-type = ; + + pon_perph_reg: qcom,pon_perph_reg { + regulator-name = "pon_spare_reg"; + qcom,pon-spare-reg-addr = <0x8c>; + qcom,pon-spare-reg-bit = <1>; + }; + }; diff --git a/bindings/mfd/qcom-pm8xxx.txt b/bindings/mfd/qcom-pm8xxx.txt index 9e5eba4a4f0d..07f49254f366 100644 --- a/bindings/mfd/qcom-pm8xxx.txt +++ b/bindings/mfd/qcom-pm8xxx.txt @@ -64,6 +64,7 @@ The below bindings specify the set of valid subnodes. "qcom,pm8921-rtc" "qcom,pm8941-rtc" "qcom,pm8018-rtc" + "qcom,pmk8350-rtc" - reg: Usage: required diff --git a/qcom/lahaina-cdp.dtsi b/qcom/lahaina-cdp.dtsi index e69de29bb2d1..2e3ab49ddbbe 100644 --- a/qcom/lahaina-cdp.dtsi +++ b/qcom/lahaina-cdp.dtsi @@ -0,0 +1,5 @@ +#include "lahaina-pmic-overlay.dtsi" + +&spmi_debug_bus { + status = "ok"; +}; diff --git a/qcom/lahaina-mtp.dtsi b/qcom/lahaina-mtp.dtsi index e69de29bb2d1..2e3ab49ddbbe 100644 --- a/qcom/lahaina-mtp.dtsi +++ b/qcom/lahaina-mtp.dtsi @@ -0,0 +1,5 @@ +#include "lahaina-pmic-overlay.dtsi" + +&spmi_debug_bus { + status = "ok"; +}; diff --git a/qcom/lahaina-pmic-overlay.dtsi b/qcom/lahaina-pmic-overlay.dtsi new file mode 100644 index 000000000000..e01ee2450d01 --- /dev/null +++ b/qcom/lahaina-pmic-overlay.dtsi @@ -0,0 +1,8 @@ +#include + +#include "pmk8350.dtsi" +#include "pm8350.dtsi" +#include "pm8350c.dtsi" +#include "pm8350b.dtsi" +#include "pmr735a.dtsi" +#include "pmr735b.dtsi" diff --git a/qcom/lahaina-qrd.dtsi b/qcom/lahaina-qrd.dtsi index e69de29bb2d1..2e3ab49ddbbe 100644 --- a/qcom/lahaina-qrd.dtsi +++ b/qcom/lahaina-qrd.dtsi @@ -0,0 +1,5 @@ +#include "lahaina-pmic-overlay.dtsi" + +&spmi_debug_bus { + status = "ok"; +}; diff --git a/qcom/lahaina-rumi.dtsi b/qcom/lahaina-rumi.dtsi index baf5e635a33c..25f5de69b125 100644 --- a/qcom/lahaina-rumi.dtsi +++ b/qcom/lahaina-rumi.dtsi @@ -1,4 +1,9 @@ #include "lahaina.dtsi" +#include "lahaina-pmic-overlay.dtsi" + +&spmi_debug_bus { + status = "ok"; +}; &ufsphy_mem { compatible = "qcom,ufs-phy-qrbtc-sdm845"; diff --git a/qcom/lahaina.dtsi b/qcom/lahaina.dtsi index 9cef92ca4931..ea605fe98df2 100644 --- a/qcom/lahaina.dtsi +++ b/qcom/lahaina.dtsi @@ -10,6 +10,7 @@ #include #include #include +#include #include #include @@ -876,6 +877,9 @@ qcom,retain-regs; }; + thermal_zones: thermal-zones { + }; + cache-controller@9200000 { compatible = "qcom,lahaina-llcc", "qcom,llcc-v2"; reg = <0x9200000 0x1d0000> , <0x9600000 0x50000>; @@ -1202,6 +1206,66 @@ qcom,ee = <0>; }; + spmi_debug_bus: qcom,spmi-debug@6b12000 { + compatible = "qcom,spmi-pmic-arb-debug"; + reg = <0x6b12000 0x60>, <0x7820a8 0x4>; + reg-names = "core", "fuse"; + clocks = <&clock_aop QDSS_CLK>; + clock-names = "core_clk"; + qcom,fuse-disable-bit = <24>; + #address-cells = <2>; + #size-cells = <0>; + status = "disabled"; + + qcom,pmk8350-debug@0 { + compatible = "qcom,spmi-pmic"; + reg = <0 SPMI_USID>; + #address-cells = <2>; + #size-cells = <0>; + qcom,can-sleep; + }; + + qcom,pm8350-debug@1 { + compatible = "qcom,spmi-pmic"; + reg = <1 SPMI_USID>; + #address-cells = <2>; + #size-cells = <0>; + qcom,can-sleep; + }; + + qcom,pm8350c-debug@2 { + compatible = "qcom,spmi-pmic"; + reg = <2 SPMI_USID>; + #address-cells = <2>; + #size-cells = <0>; + qcom,can-sleep; + }; + + qcom,pm8350b-debug@3 { + compatible = "qcom,spmi-pmic"; + reg = <3 SPMI_USID>; + #address-cells = <2>; + #size-cells = <0>; + qcom,can-sleep; + }; + + qcom,pmr735a-debug@4 { + compatible = "qcom,spmi-pmic"; + reg = <4 SPMI_USID>; + #address-cells = <2>; + #size-cells = <0>; + qcom,can-sleep; + }; + + qcom,pmr735b-debug@5 { + compatible = "qcom,spmi-pmic"; + reg = <5 SPMI_USID>; + #address-cells = <2>; + #size-cells = <0>; + qcom,can-sleep; + }; + }; + qcom,msm-cdsp-loader { compatible = "qcom,cdsp-loader"; qcom,proc-img-to-load = "cdsp"; diff --git a/qcom/pm8350.dtsi b/qcom/pm8350.dtsi new file mode 100644 index 000000000000..1b79409a0e74 --- /dev/null +++ b/qcom/pm8350.dtsi @@ -0,0 +1,61 @@ +#include +#include + +&spmi_bus { + #address-cells = <2>; + #size-cells = <0>; + interrupt-controller; + #interrupt-cells = <4>; + + qcom,pm8350@1 { + compatible = "qcom,spmi-pmic"; + reg = <1 SPMI_USID>; + #address-cells = <1>; + #size-cells = <0>; + + pm8350_tz: qcom,temp-alarm@a00 { + compatible = "qcom,spmi-temp-alarm"; + reg = <0xa00>; + interrupts = <0x1 0xa 0x0 IRQ_TYPE_EDGE_BOTH>; + #thermal-sensor-cells = <0>; + }; + + pm8350_gpios: pinctrl@8800 { + compatible = "qcom,pm8350-gpio"; + reg = <0x8800>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + }; +}; + +&thermal_zones { + pm8350_temp_alarm: pm8350_tz { + polling-delay-passive = <100>; + polling-delay = <0>; + thermal-governor = "step_wise"; + thermal-sensors = <&pm8350_tz>; + + trips { + pm8350_trip0: trip0 { + temperature = <95000>; + hysteresis = <0>; + type = "passive"; + }; + + pm8350_trip1: trip1 { + temperature = <115000>; + hysteresis = <0>; + type = "passive"; + }; + + pm8350_trip2: trip2 { + temperature = <145000>; + hysteresis = <0>; + type = "passive"; + }; + }; + }; +}; diff --git a/qcom/pm8350b.dtsi b/qcom/pm8350b.dtsi new file mode 100644 index 000000000000..aeeb5680dc75 --- /dev/null +++ b/qcom/pm8350b.dtsi @@ -0,0 +1,61 @@ +#include +#include + +&spmi_bus { + #address-cells = <2>; + #size-cells = <0>; + interrupt-controller; + #interrupt-cells = <4>; + + qcom,pm8350b@3 { + compatible = "qcom,spmi-pmic"; + reg = <3 SPMI_USID>; + #address-cells = <1>; + #size-cells = <0>; + + pm8350b_tz: qcom,temp-alarm@a00 { + compatible = "qcom,spmi-temp-alarm"; + reg = <0xa00>; + interrupts = <0x3 0xa 0x0 IRQ_TYPE_EDGE_BOTH>; + #thermal-sensor-cells = <0>; + }; + + pm8350b_gpios: pinctrl@8800 { + compatible = "qcom,pm8350b-gpio"; + reg = <0x8800>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + }; +}; + +&thermal_zones { + pm8350b_temp_alarm: pm8350b_tz { + polling-delay-passive = <100>; + polling-delay = <0>; + thermal-governor = "step_wise"; + thermal-sensors = <&pm8350b_tz>; + + trips { + pm8350b_trip0: trip0 { + temperature = <95000>; + hysteresis = <0>; + type = "passive"; + }; + + pm8350b_trip1: trip1 { + temperature = <115000>; + hysteresis = <0>; + type = "passive"; + }; + + pm8350b_trip2: trip2 { + temperature = <145000>; + hysteresis = <0>; + type = "passive"; + }; + }; + }; +}; diff --git a/qcom/pm8350c.dtsi b/qcom/pm8350c.dtsi new file mode 100644 index 000000000000..ed51205ade31 --- /dev/null +++ b/qcom/pm8350c.dtsi @@ -0,0 +1,61 @@ +#include +#include + +&spmi_bus { + #address-cells = <2>; + #size-cells = <0>; + interrupt-controller; + #interrupt-cells = <4>; + + qcom,pm8350c@2 { + compatible = "qcom,spmi-pmic"; + reg = <2 SPMI_USID>; + #address-cells = <1>; + #size-cells = <0>; + + pm8350c_tz: qcom,temp-alarm@a00 { + compatible = "qcom,spmi-temp-alarm"; + reg = <0xa00>; + interrupts = <0x2 0xa 0x0 IRQ_TYPE_EDGE_BOTH>; + #thermal-sensor-cells = <0>; + }; + + pm8350c_gpios: pinctrl@8800 { + compatible = "qcom,pm8350c-gpio"; + reg = <0x8800>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + }; +}; + +&thermal_zones { + pm8350c_temp_alarm: pm8350c_tz { + polling-delay-passive = <100>; + polling-delay = <0>; + thermal-governor = "step_wise"; + thermal-sensors = <&pm8350c_tz>; + + trips { + pm8350c_trip0: trip0 { + temperature = <95000>; + hysteresis = <0>; + type = "passive"; + }; + + pm8350c_trip1: trip1 { + temperature = <115000>; + hysteresis = <0>; + type = "passive"; + }; + + pm8350c_trip2: trip2 { + temperature = <145000>; + hysteresis = <0>; + type = "passive"; + }; + }; + }; +}; diff --git a/qcom/pmk8350.dtsi b/qcom/pmk8350.dtsi new file mode 100644 index 000000000000..355dedbd2c30 --- /dev/null +++ b/qcom/pmk8350.dtsi @@ -0,0 +1,38 @@ +#include +#include +#include + +&spmi_bus { + #address-cells = <2>; + #size-cells = <0>; + interrupt-controller; + #interrupt-cells = <4>; + + qcom,pmk8350@0 { + compatible = "qcom,spmi-pmic"; + reg = <0 SPMI_USID>; + #address-cells = <1>; + #size-cells = <0>; + + pmk8350_sdam_2: sdam@7100 { + compatible = "qcom,spmi-sdam"; + reg = <0x7100>; + }; + + pmk8350_gpios: pinctrl@b000 { + compatible = "qcom,pmk8350-gpio"; + reg = <0xb000>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + pmk8350_rtc: rtc@6100 { + compatible = "qcom,pmk8350-rtc"; + reg = <0x6100>, <0x6200>; + reg-names = "rtc", "alarm"; + interrupts = <0x0 0x62 0x1 IRQ_TYPE_EDGE_RISING>; + }; + }; +}; diff --git a/qcom/pmr735a.dtsi b/qcom/pmr735a.dtsi new file mode 100644 index 000000000000..3e8ca911ad2a --- /dev/null +++ b/qcom/pmr735a.dtsi @@ -0,0 +1,61 @@ +#include +#include + +&spmi_bus { + #address-cells = <2>; + #size-cells = <0>; + interrupt-controller; + #interrupt-cells = <4>; + + qcom,pmr735a@4 { + compatible = "qcom,spmi-pmic"; + reg = <4 SPMI_USID>; + #address-cells = <1>; + #size-cells = <0>; + + pmr735a_tz: qcom,temp-alarm@a00 { + compatible = "qcom,spmi-temp-alarm"; + reg = <0xa00>; + interrupts = <0x4 0xa 0x0 IRQ_TYPE_EDGE_BOTH>; + #thermal-sensor-cells = <0>; + }; + + pmr735a_gpios: pinctrl@8800 { + compatible = "qcom,pmr735a-gpio"; + reg = <0x8800>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + }; +}; + +&thermal_zones { + pmr735a_temp_alarm: pmr735a_tz { + polling-delay-passive = <100>; + polling-delay = <0>; + thermal-governor = "step_wise"; + thermal-sensors = <&pmr735a_tz>; + + trips { + pmr735a_trip0: trip0 { + temperature = <95000>; + hysteresis = <0>; + type = "passive"; + }; + + pmr735a_trip1: trip1 { + temperature = <115000>; + hysteresis = <0>; + type = "passive"; + }; + + pmr735a_trip2: trip2 { + temperature = <145000>; + hysteresis = <0>; + type = "passive"; + }; + }; + }; +}; diff --git a/qcom/pmr735b.dtsi b/qcom/pmr735b.dtsi new file mode 100644 index 000000000000..b1050bf06072 --- /dev/null +++ b/qcom/pmr735b.dtsi @@ -0,0 +1,61 @@ +#include +#include + +&spmi_bus { + #address-cells = <2>; + #size-cells = <0>; + interrupt-controller; + #interrupt-cells = <4>; + + qcom,pmr735b@5 { + compatible = "qcom,spmi-pmic"; + reg = <5 SPMI_USID>; + #address-cells = <1>; + #size-cells = <0>; + + pmr735b_tz: qcom,temp-alarm@a00 { + compatible = "qcom,spmi-temp-alarm"; + reg = <0xa00>; + interrupts = <0x5 0xa 0x0 IRQ_TYPE_EDGE_BOTH>; + #thermal-sensor-cells = <0>; + }; + + pmr735b_gpios: pinctrl@8800 { + compatible = "qcom,pmr735b-gpio"; + reg = <0x8800>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + }; +}; + +&thermal_zones { + pmr735b_temp_alarm: pmr735b_tz { + polling-delay-passive = <100>; + polling-delay = <0>; + thermal-governor = "step_wise"; + thermal-sensors = <&pmr735b_tz>; + + trips { + pmr735b_trip0: trip0 { + temperature = <95000>; + hysteresis = <0>; + type = "passive"; + }; + + pmr735b_trip1: trip1 { + temperature = <115000>; + hysteresis = <0>; + type = "passive"; + }; + + pmr735b_trip2: trip2 { + temperature = <145000>; + hysteresis = <0>; + type = "passive"; + }; + }; + }; +};