The buffer size on nxt200x is not enough:
...
> Dec 20 10:52:04 rich kernel: [ 31.747949] nxt200x: nxt200x_writebytes: i2c wr reg=002c: len=255 is too big!
...
Increase it to 256 bytes.
Reported-by: Rich Freeman <rich0@gentoo.org>
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
On ARM-based SHMOBILE, the rspi driver builds and works fine without the
DMA controller driver, hence relax the dependencies.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Some old AD codecs don't like the independent HP handling, either it
contains a single DAC (AD1981) or it mandates the mixer routing
(AD1986A). This patch removes the indep_hp flag for such codecs.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=68081
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We have a spi_sh_clear_bit() function, there's no reason not to use it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
- Rephrase the comments about tx/rx_nbits validity checks,
- Remove the stale comment about SPI_3WIRE (the code it refers to was
removed in commit 368ca4e0c7 ("spi:
Eliminate 3WIRE spi_transfer check")).
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
spi_write_then_read() takes a "void *" for rxbuf, so there's no need to
cast the buffer pointer to "u8 *".
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
In futex_wake() there is clearly no point in taking the hb->lock
if we know beforehand that there are no tasks to be woken. While
the hash bucket's plist head is a cheap way of knowing this, we
cannot rely 100% on it as there is a racy window between the
futex_wait call and when the task is actually added to the
plist. To this end, we couple it with the spinlock check as
tasks trying to enter the critical region are most likely
potential waiters that will be added to the plist, thus
preventing tasks sleeping forever if wakers don't acknowledge
all possible waiters.
Furthermore, the futex ordering guarantees are preserved,
ensuring that waiters either observe the changed user space
value before blocking or is woken by a concurrent waker. For
wakers, this is done by relying on the barriers in
get_futex_key_refs() -- for archs that do not have implicit mb
in atomic_inc(), we explicitly add them through a new
futex_get_mm function. For waiters we rely on the fact that
spin_lock calls already update the head counter, so spinners
are visible even if the lock hasn't been acquired yet.
For more details please refer to the updated comments in the
code and related discussion:
https://lkml.org/lkml/2013/11/26/556
Special thanks to tglx for careful review and feedback.
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Reviewed-by: Darren Hart <dvhart@linux.intel.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Davidlohr Bueso <davidlohr@hp.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Jeff Mahoney <jeffm@suse.com>
Cc: Scott Norton <scott.norton@hp.com>
Cc: Tom Vaden <tom.vaden@hp.com>
Cc: Aswin Chandramouleeswaran <aswin@hp.com>
Cc: Waiman Long <Waiman.Long@hp.com>
Cc: Jason Low <jason.low2@hp.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: http://lkml.kernel.org/r/1389569486-25487-5-git-send-email-davidlohr@hp.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
That's essential, if you want to hack on futexes.
Reviewed-by: Darren Hart <dvhart@linux.intel.com>
Reviewed-by: Peter Zijlstra <peterz@infradead.org>
Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Davidlohr Bueso <davidlohr@hp.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Jeff Mahoney <jeffm@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Scott Norton <scott.norton@hp.com>
Cc: Tom Vaden <tom.vaden@hp.com>
Cc: Aswin Chandramouleeswaran <aswin@hp.com>
Cc: Waiman Long <Waiman.Long@hp.com>
Cc: Jason Low <jason.low2@hp.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: http://lkml.kernel.org/r/1389569486-25487-4-git-send-email-davidlohr@hp.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Currently, the futex global hash table suffers from its fixed,
smallish (for today's standards) size of 256 entries, as well as
its lack of NUMA awareness. Large systems, using many futexes,
can be prone to high amounts of collisions; where these futexes
hash to the same bucket and lead to extra contention on the same
hb->lock. Furthermore, cacheline bouncing is a reality when we
have multiple hb->locks residing on the same cacheline and
different futexes hash to adjacent buckets.
This patch keeps the current static size of 16 entries for small
systems, or otherwise, 256 * ncpus (or larger as we need to
round the number to a power of 2). Note that this number of CPUs
accounts for all CPUs that can ever be available in the system,
taking into consideration things like hotpluging. While we do
impose extra overhead at bootup by making the hash table larger,
this is a one time thing, and does not shadow the benefits of
this patch.
Furthermore, as suggested by tglx, by cache aligning the hash
buckets we can avoid access across cacheline boundaries and also
avoid massive cache line bouncing if multiple cpus are hammering
away at different hash buckets which happen to reside in the
same cache line.
Also, similar to other core kernel components (pid, dcache,
tcp), by using alloc_large_system_hash() we benefit from its
NUMA awareness and thus the table is distributed among the nodes
instead of in a single one.
For a custom microbenchmark that pounds on the uaddr hashing --
making the wait path fail at futex_wait_setup() returning
-EWOULDBLOCK for large amounts of futexes, we can see the
following benefits on a 80-core, 8-socket 1Tb server:
+---------+--------------------+------------------------+-----------------------+-------------------------------+
| threads | baseline (ops/sec) | aligned-only (ops/sec) | large table (ops/sec) | large table+aligned (ops/sec) |
+---------+--------------------+------------------------+-----------------------+-------------------------------+
| 512 | 32426 | 50531 (+55.8%) | 255274 (+687.2%) | 292553 (+802.2%) |
| 256 | 65360 | 99588 (+52.3%) | 443563 (+578.6%) | 508088 (+677.3%) |
| 128 | 125635 | 200075 (+59.2%) | 742613 (+491.1%) | 835452 (+564.9%) |
| 80 | 193559 | 323425 (+67.1%) | 1028147 (+431.1%) | 1130304 (+483.9%) |
| 64 | 247667 | 443740 (+79.1%) | 997300 (+302.6%) | 1145494 (+362.5%) |
| 32 | 628412 | 721401 (+14.7%) | 965996 (+53.7%) | 1122115 (+78.5%) |
+---------+--------------------+------------------------+-----------------------+-------------------------------+
Reviewed-by: Darren Hart <dvhart@linux.intel.com>
Reviewed-by: Peter Zijlstra <peterz@infradead.org>
Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Waiman Long <Waiman.Long@hp.com>
Reviewed-and-tested-by: Jason Low <jason.low2@hp.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Davidlohr Bueso <davidlohr@hp.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Jeff Mahoney <jeffm@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Scott Norton <scott.norton@hp.com>
Cc: Tom Vaden <tom.vaden@hp.com>
Cc: Aswin Chandramouleeswaran <aswin@hp.com>
Link: http://lkml.kernel.org/r/1389569486-25487-3-git-send-email-davidlohr@hp.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJS0miqAAoJEHm+PkMAQRiGbfgIAJSWEfo8ludknhPcHJabBtxu
75SQAKJlL3sBVnxEc58Rtt8gsKYQIrm4IY5Slunklsn04RxuDUIQMgFoAYR5gQwz
+Myqkw/HOqDe5VStGxtLYpWnfglxVwGDCd7ISfL9AOVy5adMWBxh4Tv+qqQc7aIZ
eF7dy+DD+C6Q3Z5OoV8s0FZDxse29vOf17Nki7+7t8WMqyegYwjoOqNeqocGKsPi
eHLrJgTl4T6jB4l9LKKC154DSKjKOTSwZMWgwK8mToyNLT/ufCiKgXloIjEvZZcY
VVKUtncdHiTf+iqVojgpGBzOEeB5DM83iiapFeDiJg8C9yBzvT8lBtA9aPb5Wgw=
=lEeV
-----END PGP SIGNATURE-----
Merge tag 'v3.13-rc8' into core/locking
Refresh the tree with the latest fixes, before applying new changes.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The locking in the acx565akm panel driver was getting too complex. Clean
it up by making new functions, acx565akm_bl_get_intensity_locked and
acx565akm_bl_update_status_locked, which are called by the backlight
subsystem. This way the non-locked versions can be called by the panel's
other funcs, simplifying the lock management.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
DISPC pipeline DMAs preload some bytes of pixel data in the vertical blanking
region before the start of each frame. The preload ensures the pipeline doesn't
underflow when the active region of the display starts.
DISPC_GFX/VIDp_PRELOAD registers allow us to program how many bytes of data
should be preloaded for each pipeline. Calculating a precise preload value
would be a complex function of the pixel clock of the connected display, the
vertical blanking duration and the interconnect traffic at that instance. If
the register is left untouched, a default value is preloaded.
We observe underflows for OMAP4+ SoCs for certain bandwidth intensive use cases
with many other initiators active, and in situations where memory access isn't
very efficient(like accessing Tiler mapped buffers and EMIF configured in
non-interleaved more). The cause of the underflow is because the default preload
value isn't sufficient for the DMA to reach a steady state. We configure the
PRELOAD register such that the pipelines preload data up to the high threshold
of the FIFO.
Preloading lot of data for older SoCs can have a negative impact. Due to slower
interconnects, it's possible that the DISPC DMA cannot preload up to the high
threshold within the vertical blanking region of the panel. We leave the PRELOAD
registers to their reset values since we haven't faced underflows with these
SoCs because of low value of PRELOAD.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
When omapfb module is removed, the driver will turn off all the displays
it manages. However, it leaves the overlays enabled. While the overlays
are obviously disabled as the displays are disabled, it causes issues
when the driver module is loaded again, as at that point the overlays
are still enabled on the hardware level. The result is that even if the
SW thinks overlays are disabled, they are actually enabled.
Fix this by making sure the overlays are disabled at module removal.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Nowadays it's normal to get -EPROBE_DEFER from, e.g., regulator_get. As
-EPROBE_DEFER is not really an error, and the driver will be probed fine
a bit later, printing an error message will just confuse the user.
This patch changes omapdss to print an error for regulator_gets only if
the error code is something else than -EPROBE_DEFER.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
It is quite common to have omapfb probe deferred because of a missing
resource, and to get omapfb probed succesfully a bit later. This works
fine. However, omapfb does not give any print on a successful probe, so
if the omapfb is actually never probed again after deferral, this is not
shown in the log.
To help debugging, add a simple print from omapfb at the end of its
probe, saying which display it is using and in which resolution.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The HDMI driver tries to get the needed memory resources by name and by
ID. Resources by name are not currently defined, and will be used with
DT boot.
The resource names used in the driver are not quite perfect, and as they
are not used yet, we can change them. This patch removes the unneeded
"hdmi_" prefix from the names, and simplifies the names (e.g. hdmi_txphy
-> phy).
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
DSI contains three separate blocks: protocol engine, PHY and PLL. At the
moment, all these are memory mapped in one big chunk. We need to split
that memory map into smaller pieces so that we can add proper 'reg'
properties into the DT data for each block.
This patch changes the driver to map the blocks separately. It first
tries to get the memory resource using name, used when booting with DT,
and if that fails, it gets the memory resource by ID, in which case the
driver gets the big chunk from platform data. That big chunk is then
split into the smaller blocks manually.
After DSS DT code has been merged and the old platform code removed, we
can clean up the memory resource management.
Instead of changing the driver in all the places where a register is
read or written, this patch takes a shortcut: it adds an additional
number to the struct which represents the register index. This number is
used to decide which base address to use. In the future we should
consider other approaches.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
hdmi_wait_for_bit_change() has two issues:
The register index was passed as u16, even if the register index may be
u32. Fix the index to u32.
The function was copied from wait_for_bit_change() which waits for a
single bit to change, but the hdmi version was changed to wait for a bit
field. This change was not done correctly.
The function is supposed to return the (last) value of the bit field,
but it returned !val in case of timeout. This was correct for the single
bit version, but not for the hdmi version. Fix the function to return
the actual value in the register.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
DISPC_MSTANDBY_CTRL register is used in the driver, but it's not
restored in dispc_restore_context(), causing problems after resume.
Instead of adding DISPC_MSTANDBY_CTRL to dispc_restore_context(), let's
call _omap_dispc_initial_config() as the first thing in
dispc_runtime_resume(). This will initialize the DISPC core registers
properly, and will avoid similar issues in the future.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
For some reason the hdmi driver first turns off the video output when
it's about to enable the video output. This serves no purpose, and can
be removed.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The hdmi4 driver currently rejects any timing which is not from the CEA or VESA
standards. This leads hdmi rejecting any non-standard mode. A non standard
timing may not have a valid code corresponding to it. In such cases, the HDMI
spec suggests to set the code to 0.
Modify the driver to check if the timings fall within the range of the DISPC
TV overlay manager, and remove the check for an invalid code. Add a debug print
specifying the mode and code in hdmi_display_set_timing.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The driver name in current code looks like a compatible string which is not
the naming convention for platform drivers.
Fix it and also add modalias since this driver can be built as a module.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Make the unit of wlen to be byte, and simplify the code to avoid duplicate
code for different wlen cases.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Trent Piepho observed that since the current realistic maximum number of
data lines is four we can pack the spi_transfer struct more efficiently
if we use a bitfield for the number of bits, allowing the fields to fit
in a single byte along with cs_change.
If space becomes an issue further optimiation is possible by only using
the constants and packing the values chosen for them.
Reported-by: Trent Piepho <tpiepho@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
We already has NULL test for master after calling spi_alloc_master().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
i.MX series have inner firmware in its ROM code: when SDMA isn't provided
any firmware from Kernel or rootfs, the default inner ROM firmware will be
activated. However the current driver doesn't assign any script number to
this situation, and those platform running in this case would be broken.
Thus this patch adds a default script number when no external firmware being
loaded so that people would continue to be able to use basic scripts to run
their platform without any firmware.
Reported-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This reverts commit b1d27c79c8.
Previously we switched the SSI scriprt to dual-fifo mode to reduce playback
underrun issue, which is only included by SDMA firmware version 2. However,
there are quite a lot people still using version 1 or default firmware in
the ROM code of SoC while these two kinds of firmwares do not support the
dual-fifo script and the audio function on their platform would be broken.
Thus this patch provisionally reverts the dual-fifo script to the original
single fifo script to meet all kinds of users' requirements, including the
version 1/2 or inner ROM firmware.
Reported-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Some Atari hardware has no capacity to raise interrupts (e.g.
network or USB adapter hardware attached via ROM port). The driver
interrupt routine is called from a timer interrupt (timer D) in
these cases, using chained device specific pseudo interrupts
(IRQ_MFP_TIMER1 ff.)
These interrupts will more often than not, return IRQ_NONE as
there is not always work for the device handler when called.
Too many unhandled interrupts will result in the interrupt
being disabled by the stuck interrupt watchdog.
As preferred option to flag interrupts as needing exclusion
from the watchdog mechanism, tglx added the IRQ_IS_POLLED flag
for use in such a case. Currently, two interrupts need to use
this flag. Add more users as needed.
Signed-off-by: Michael Schmitz <schmitz@debian.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Commit c02cecb92e ("ARM: orion: move platform_data definitions")
moved the file to the current location but forgot to remove the pointer
to its previous location. Clean it up. While at it also change the header
file protection macros appropriately.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Commit 293b2da1b6 ("ARM: pxa: move platform_data definitions")
moved the file to the current location but forgot to remove the pointer
to its previous location. Clean it up. While at it also change the header
file protection macros appropriately.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
