After reset SGMII Autoneg timer is set to 2us (bits 6 and 5 are 01).
That is not enough to finalize autonegatiation on some devices.
Increase this timer duration to maximum supported 16ms.
Signed-off-by: Max Uvarov <muvarov@gmail.com>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For supporting 10Mps speed in SGMII mode DP83867_10M_SGMII_RATE_ADAPT bit
of DP83867_10M_SGMII_CFG register has to be cleared by software.
That does not affect speeds 100 and 1000 so can be done on init.
Signed-off-by: Max Uvarov <muvarov@gmail.com>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some boards do not have the PHY firmware programmed in the 3310's flash,
which leads to the PHY not working as expected. Warn the user when the
PHY fails to boot the firmware and refuse to initialise.
Fixes: 20b2af32ff ("net: phy: add Marvell Alaska X 88X3310 10Gigabit PHY support")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ensure that we supply the same phy interface mode to mac_link_down() as
we did for the corresponding mac_link_up() call. This ensures that MAC
drivers that use the phy interface mode in these methods can depend on
mac_link_down() always corresponding to a mac_link_up() call for the
same interface mode.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
A PF_EXITING task can stay associated with an offline css. If such
task calls task_get_css(), it can get stuck indefinitely. This can be
triggered by BSD process accounting which writes to a file with
PF_EXITING set when racing against memcg disable as in the backtrace
at the end.
After this change, task_get_css() may return a css which was already
offline when the function was called. None of the existing users are
affected by this change.
INFO: rcu_sched self-detected stall on CPU
INFO: rcu_sched detected stalls on CPUs/tasks:
...
NMI backtrace for cpu 0
...
Call Trace:
<IRQ>
dump_stack+0x46/0x68
nmi_cpu_backtrace.cold.2+0x13/0x57
nmi_trigger_cpumask_backtrace+0xba/0xca
rcu_dump_cpu_stacks+0x9e/0xce
rcu_check_callbacks.cold.74+0x2af/0x433
update_process_times+0x28/0x60
tick_sched_timer+0x34/0x70
__hrtimer_run_queues+0xee/0x250
hrtimer_interrupt+0xf4/0x210
smp_apic_timer_interrupt+0x56/0x110
apic_timer_interrupt+0xf/0x20
</IRQ>
RIP: 0010:balance_dirty_pages_ratelimited+0x28f/0x3d0
...
btrfs_file_write_iter+0x31b/0x563
__vfs_write+0xfa/0x140
__kernel_write+0x4f/0x100
do_acct_process+0x495/0x580
acct_process+0xb9/0xdb
do_exit+0x748/0xa00
do_group_exit+0x3a/0xa0
get_signal+0x254/0x560
do_signal+0x23/0x5c0
exit_to_usermode_loop+0x5d/0xa0
prepare_exit_to_usermode+0x53/0x80
retint_user+0x8/0x8
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org # v4.2+
Fixes: ec438699a9 ("cgroup, block: implement task_get_css() and use it in bio_associate_current()")
If blk_mq_init_allocated_queue() fails, make sure to free the poll
stat callback struct allocated.
Signed-off-by: Jes Sorensen <jsorensen@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Fix the following sparse context imbalance regression introduced in
a patch that fixed sleeping function called from invalid context bug.
kbuild test robot reported on:
tree/branch: https://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb.git usb-linus
Regressions in current branch:
drivers/usb/usbip/stub_dev.c:399:9: sparse: sparse: context imbalance in 'stub_probe' - different lock contexts for basic block
drivers/usb/usbip/stub_dev.c:418:13: sparse: sparse: context imbalance in 'stub_disconnect' - different lock contexts for basic block
drivers/usb/usbip/stub_dev.c:464:1-10: second lock on line 476
Error ids grouped by kconfigs:
recent_errors
├── i386-allmodconfig
│ └── drivers-usb-usbip-stub_dev.c:second-lock-on-line
├── x86_64-allmodconfig
│ ├── drivers-usb-usbip-stub_dev.c:sparse:sparse:context-imbalance-in-stub_disconnect-different-lock-contexts-for-basic-block
│ └── drivers-usb-usbip-stub_dev.c:sparse:sparse:context-imbalance-in-stub_probe-different-lock-contexts-for-basic-block
└── x86_64-allyesconfig
└── drivers-usb-usbip-stub_dev.c:second-lock-on-line
This is a real problem in an error leg where spin_lock() is called on an
already held lock.
Fix the imbalance in stub_probe() and stub_disconnect().
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Fixes: 0c9e8b3cad ("usbip: usbip_host: fix BUG: sleeping function called from invalid context")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sh_eth_close() resets the MAC and then calls phy_stop()
so that mdio read access result is incorrect without any error
according to kernel trace like below:
ifconfig-216 [003] .n.. 109.133124: mdio_access: ee700000.ethernet-ffffffff read phy:0x01 reg:0x00 val:0xffff
According to the hardware manual, the RMII mode should be set to 1
before operation the Ethernet MAC. However, the previous code was not
set to 1 after the driver issued the soft_reset in sh_eth_dev_exit()
so that the mdio read access result seemed incorrect. To fix the issue,
this patch adds a condition and set the RMII mode register in
sh_eth_dev_exit() for R-Car Gen2 and RZ/A1 SoCs.
Note that when I have tried to move the sh_eth_dev_exit() calling
after phy_stop() on sh_eth_close(), but it gets worse (kernel panic
happened and it seems that a register is accessed while the clock is
off).
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
arch/mips/kernel/uprobes.c: In function 'arch_uprobe_pre_xol':
arch/mips/kernel/uprobes.c:115:17: warning: variable 'epc' set but not used [-Wunused-but-set-variable]
It's never used since introduction in
commit 40e084a506 ("MIPS: Add uprobes support.")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: <ralf@linux-mips.org>
Cc: <jhogan@kernel.org>
Cc: <linux-kernel@vger.kernel.org>
Cc: <linux-mips@vger.kernel.org>
This Kselftest update for Linux 5.2-rc3 consists of
- Alexandre Belloni's fixes to rtc regressions introduced in kselftest
Makefile test run output refactoring work from Kees Cook.
- ftrace test checkbashisms fixes from Masami Hiramatsu
-----BEGIN PGP SIGNATURE-----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=zYD6
-----END PGP SIGNATURE-----
Merge tag 'linux-kselftest-5.2-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull Kselftest fixes from Shuah Khan:
- Alexandre Belloni's fixes to rtc regressions introduced in kselftest
Makefile test run output refactoring work from Kees Cook.
- ftrace test checkbashisms fixes from Masami Hiramatsu
* tag 'linux-kselftest-5.2-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
selftests: rtc: rtctest: specify timeouts
selftests/harness: Allow test to configure timeout
selftests/ftrace: Add checkbashisms meta-testcase
selftests/ftrace: Make a script checkbashisms clean
This patch fixes a complain about possible sleep during
spinlock aquired
"BUG: sleeping function called from invalid context at
include/crypto/algapi.h:426"
for the ctr(aes) and ctr(des) s390 specific ciphers.
Instead of using a spinlock this patch introduces a mutex
which is save to be held in sleeping context. Please note
a deadlock is not possible as mutex_trylock() is used.
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Reported-by: Julian Wiedmann <jwi@linux.ibm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
The pistachio platform uses the U-Boot bootloader & generally boots a
kernel in the uImage format. As such it's useful to build one when
building the kernel, but to do so currently requires the user to
manually specify a uImage target on the make command line.
Make uImage.gz the pistachio platform's default build target, so that
the default is to build a kernel image that we can actually boot on a
board such as the MIPS Creator Ci40.
Marked for stable backport as far as v4.1 where pistachio support was
introduced. This is primarily useful for CI systems such as kernelci.org
which will benefit from us building a suitable image which can then be
booted as part of automated testing, extending our test coverage to the
affected stable branches.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
URL: https://groups.io/g/kernelci/message/388
Cc: stable@vger.kernel.org # v4.1+
Cc: linux-mips@vger.kernel.org
virt_addr_valid() really returns a boolean value, but currently uses an
integer to represent it. Switch to the bool type to make it clearer that
we really are returning a true or false value.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Cc: linux-mips@vger.kernel.org
The virt_addr_valid() function is meant to return true iff
virt_to_page() will return a valid struct page reference. This is true
iff the address provided is found within the unmapped address range
between PAGE_OFFSET & MAP_BASE, but we don't currently check for that
condition. Instead we simply mask the address to obtain what will be a
physical address if the virtual address is indeed in the desired range,
shift it to form a PFN & then call pfn_valid(). This can incorrectly
return true if called with a virtual address which, after masking,
happens to form a physical address corresponding to a valid PFN.
For example we may vmalloc an address in the kernel mapped region
starting a MAP_BASE & obtain the virtual address:
addr = 0xc000000000002000
When masked by virt_to_phys(), which uses __pa() & in turn CPHYSADDR(),
we obtain the following (bogus) physical address:
addr = 0x2000
In a common system with PHYS_OFFSET=0 this will correspond to a valid
struct page which should really be accessed by virtual address
PAGE_OFFSET+0x2000, causing virt_addr_valid() to incorrectly return 1
indicating that the original address corresponds to a struct page.
This is equivalent to the ARM64 change made in commit ca219452c6
("arm64: Correctly bounds check virt_addr_valid").
This fixes fallout when hardened usercopy is enabled caused by the
related commit 517e1fbeb6 ("mm/usercopy: Drop extra
is_vmalloc_or_module() check") which removed a check for the vmalloc
range that was present from the introduction of the hardened usercopy
feature.
Signed-off-by: Paul Burton <paul.burton@mips.com>
References: ca219452c6 ("arm64: Correctly bounds check virt_addr_valid")
References: 517e1fbeb6 ("mm/usercopy: Drop extra is_vmalloc_or_module() check")
Reported-by: Julien Cristau <jcristau@debian.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: YunQiang Su <ysu@wavecomp.com>
URL: https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=929366
Cc: stable@vger.kernel.org # v4.12+
Cc: linux-mips@vger.kernel.org
Cc: Yunqiang Su <ysu@wavecomp.com>
In cifs_read_allocate_pages, in case of ENOMEM, we go through
whole rdata->pages array but we have failed the allocation before
nr_pages, therefore we may end up calling put_page with NULL
pointer, causing oops
Signed-off-by: Roberto Bergantinos Corpas <rbergant@redhat.com>
Acked-by: Pavel Shilovsky <pshilov@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
CC: Stable <stable@vger.kernel.org>
-----BEGIN PGP SIGNATURE-----
iIoEABYIADIWIQRRSw7ePDh/lE+zeZMp5XQQmuv6qgUCXO303xQccm9zdGVkdEBn
b29kbWlzLm9yZwAKCRAp5XQQmuv6qlb7AP4179SWPy9RFxvxyjTmpPFPL9oR0Q26
sOTyIBN99MUTsgEA0FNWz7/FWtFDa1wbh0tEVreaTQlKEeoIYF96dkN0iwE=
=BJgg
-----END PGP SIGNATURE-----
Merge tag 'trace-v5.2-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fix from Steven Rostedt:
"This fixes a memory leak from the error path in the event filter
logic"
* tag 'trace-v5.2-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Avoid memory leak in predicate_parse()
MAYEXEC test was mistakenly added, remove it. Checking MAYEXEC in the
driver prevents it from working with userspace that uses things like EXEC
STACK. (ie some Fortran and other runtimes)
Fixes: 40909f664d ("RDMA/efa: Add EFA verbs implementation")
Reported-by: Jason Gunthorpe <jgg@ziepe.ca>
Reviewed-by: Firas JahJah <firasj@amazon.com>
Reviewed-by: Yossi Leybovich <sleybo@amazon.com>
Signed-off-by: Gal Pressman <galpress@amazon.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Commit 25c13324d0 ("IB/mlx5: Add steering SW ICM device memory type")
breaks i386 build by introducing three 64-bit divisions. As the divisor is
MLX5_SW_ICM_BLOCK_SIZE() which is always a power of 2, we can replace the
division with bit operations.
Fixes: 25c13324d0 ("IB/mlx5: Add steering SW ICM device memory type")
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
User applications can register memory regions for TID buffers that are not
aligned on page boundaries. Hfi1 is expected to pin those pages in memory
and cache the pages with mmu_rb. The rb tree will fail to insert pages
that are not aligned correctly.
Validate whether a given virtual address is page aligned before pinning.
Fixes: 7e7a436ecb ("staging/hfi1: Add TID entry program function body")
Reviewed-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Kamenee Arumugam <kamenee.arumugam@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
The command 'ibv_devinfo -v' reports 0 for max_mr.
Fix by assigning the query values after the mr lkey_table has been built
rather than early on in the driver.
Fixes: 7b1e2099ad ("IB/rdmavt: Move memory registration into rdmavt")
Reviewed-by: Josh Collier <josh.d.collier@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
By code inspection, the freeze_work is never canceled.
Fix by adding a cancel_work_sync in the shutdown path to insure it is no
longer running.
Fixes: 7724105686 ("IB/hfi1: add driver files")
Reviewed-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
The qpn allocation logic has a WARN_ON() that intends to detect the use of
an index that will introduce bits in the lower order bits of the QOS bits
in the QPN.
Unfortunately, it has the following bugs:
- it misfires when wrapping QPN allocation for non-QOS
- it doesn't correctly detect low order QOS bits (despite the comment)
The WARN_ON() should not be applied to non-QOS (qos_shift == 1).
Additionally, it SHOULD test the qpn bits per the table below:
2 data VLs: [qp7, qp6, qp5, qp4, qp3, qp2, qp1] ^
[ 0, 0, 0, 0, 0, 0, sc0], qp bit 1 always 0*
3-4 data VLs: [qp7, qp6, qp5, qp4, qp3, qp2, qp1] ^
[ 0, 0, 0, 0, 0, sc1, sc0], qp bits [21] always 0
5-8 data VLs: [qp7, qp6, qp5, qp4, qp3, qp2, qp1] ^
[ 0, 0, 0, 0, sc2, sc1, sc0] qp bits [321] always 0
Fix by qualifying the warning for qos_shift > 1 and producing the correct
mask to insure the above bits are zero without generating a superfluous
warning.
Fixes: 501edc4244 ("IB/rdmavt: Correct warning during QPN allocation")
Reviewed-by: Kaike Wan <kaike.wan@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Allwinner DAC seems to have a delay in the Speaker audio routing. When
playing a sound for the first time, the sound gets chopped. On a second
play the sound is played correctly. After some time (~5s) the issue gets
back.
This commit seems to be fixing the same issue as bf14da7 but
for another codepath.
This is the DTS that was used to debug the problem.
&codec {
allwinner,pa-gpios = <&r_pio 0 11 GPIO_ACTIVE_HIGH>; /* PL11 */
allwinner,audio-routing =
"Speaker", "LINEOUT";
status = "okay";
}
Signed-off-by: Georgii Staroselskii <georgii.staroselskii@emlid.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
to avoid screen corruption during modprobe.
Signed-off-by: Flora Cui <flora.cui@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Calling sys_ni_syscall through a syscall_fn_t pointer trips indirect
call Control-Flow Integrity checking due to a function type
mismatch. Use SYSCALL_DEFINE0 for __arm64_sys_ni_syscall instead and
remove the now unnecessary casts.
Signed-off-by: Sami Tolvanen <samitolvanen@google.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Although a syscall defined using SYSCALL_DEFINE0 doesn't accept
parameters, use the correct function type to avoid indirect call
type mismatches with Control-Flow Integrity checking.
Signed-off-by: Sami Tolvanen <samitolvanen@google.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Syscall wrappers in <asm/syscall_wrapper.h> use const struct pt_regs *
as the argument type. Use const in syscall_fn_t as well to fix indirect
call type mismatches with Control-Flow Integrity checking.
Signed-off-by: Sami Tolvanen <samitolvanen@google.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Now a063057d7c ("block: Fix a race between request queue removal and
the block cgroup controller") has been reverted, and blkcg_exit_queue()
won't be called in blk_cleanup_queue() any more.
So don't need to protect generic_make_request_checks() with
blk_queue_enter(), then the total mess can be cleaned.
37f9579f4c ("blk-mq: Avoid that submitting a bio concurrently with device
removal triggers a crash") is reverted.
Cc: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Commit 498f6650ae ("block: Fix a race between the cgroup code and
request queue initialization") moves what blk_exit_queue does into
blk_cleanup_queue() for fixing issue caused by changing back
queue lock.
However, after legacy request IO path is killed, driver queue lock
won't be used at all, and there isn't story for changing back
queue lock. Then the issue addressed by Commit 498f6650ae doesn't
exist any more.
So move move blk_exit_queue into __blk_release_queue.
This patch basically reverts the following two commits:
498f6650ae block: Fix a race between the cgroup code and request queue initialization
24ecc35853 block: Ensure that a request queue is dissociated from the cgroup controller
Cc: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Overlapping overlay layers are not supported and can cause unexpected
behavior, but overlayfs does not currently check or warn about these
configurations.
User is not supposed to specify the same directory for upper and
lower dirs or for different lower layers and user is not supposed to
specify directories that are descendants of each other for overlay
layers, but that is exactly what this zysbot repro did:
https://syzkaller.appspot.com/x/repro.syz?x=12c7a94f400000
Moving layer root directories into other layers while overlayfs
is mounted could also result in unexpected behavior.
This commit places "traps" in the overlay inode hash table.
Those traps are dummy overlay inodes that are hashed by the layers
root inodes.
On mount, the hash table trap entries are used to verify that overlay
layers are not overlapping. While at it, we also verify that overlay
layers are not overlapping with directories "in-use" by other overlay
instances as upperdir/workdir.
On lookup, the trap entries are used to verify that overlay layers
root inodes have not been moved into other layers after mount.
Some examples:
$ ./run --ov --samefs -s
...
( mkdir -p base/upper/0/u base/upper/0/w base/lower lower upper mnt
mount -o bind base/lower lower
mount -o bind base/upper upper
mount -t overlay none mnt ...
-o lowerdir=lower,upperdir=upper/0/u,workdir=upper/0/w)
$ umount mnt
$ mount -t overlay none mnt ...
-o lowerdir=base,upperdir=upper/0/u,workdir=upper/0/w
[ 94.434900] overlayfs: overlapping upperdir path
mount: mount overlay on mnt failed: Too many levels of symbolic links
$ mount -t overlay none mnt ...
-o lowerdir=upper/0/u,upperdir=upper/0/u,workdir=upper/0/w
[ 151.350132] overlayfs: conflicting lowerdir path
mount: none is already mounted or mnt busy
$ mount -t overlay none mnt ...
-o lowerdir=lower:lower/a,upperdir=upper/0/u,workdir=upper/0/w
[ 201.205045] overlayfs: overlapping lowerdir path
mount: mount overlay on mnt failed: Too many levels of symbolic links
$ mount -t overlay none mnt ...
-o lowerdir=lower,upperdir=upper/0/u,workdir=upper/0/w
$ mv base/upper/0/ base/lower/
$ find mnt/0
mnt/0
mnt/0/w
find: 'mnt/0/w/work': Too many levels of symbolic links
find: 'mnt/0/u': Too many levels of symbolic links
Reported-by: syzbot+9c69c282adc4edd2b540@syzkaller.appspotmail.com
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
With gcc 4.1:
sound/firewire/fireface/ff-protocol-latter.c: In function ‘latter_switch_fetching_mode’:
sound/firewire/fireface/ff-protocol-latter.c:97: warning: integer constant is too large for ‘long’ type
sound/firewire/fireface/ff-protocol-latter.c: In function ‘latter_begin_session’:
sound/firewire/fireface/ff-protocol-latter.c:170: warning: integer constant is too large for ‘long’ type
sound/firewire/fireface/ff-protocol-latter.c:197: warning: integer constant is too large for ‘long’ type
sound/firewire/fireface/ff-protocol-latter.c:205: warning: integer constant is too large for ‘long’ type
sound/firewire/fireface/ff-protocol-latter.c: In function ‘latter_finish_session’:
sound/firewire/fireface/ff-protocol-latter.c:214: warning: integer constant is too large for ‘long’ type
Fix this by adding the missing "ULL" suffixes.
Add the same suffix to the last constant, to maintain consistency.
Fixes: fd1cc9de64 ("ALSA: fireface: add support for Fireface UCX")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
I don't think this is userspace visible but SIGKILL does not have
any si_codes that use the fault member of the siginfo union. Correct
this the simple way and call force_sig instead of force_sig_fault when
the signal is SIGKILL.
The two know places where synchronous SIGKILL are generated are
do_bad_area and fpsimd_save. The call paths to force_sig_fault are:
do_bad_area
arm64_force_sig_fault
force_sig_fault
force_signal_inject
arm64_notify_die
arm64_force_sig_fault
force_sig_fault
Which means correcting this in arm64_force_sig_fault is enough
to ensure the arm64 code is not misusing the generic code, which
could lead to maintenance problems later.
Cc: stable@vger.kernel.org
Cc: Dave Martin <Dave.Martin@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Fixes: af40ff687b ("arm64: signal: Ensure si_code is valid for all fault signals")
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
display hardware clock will not unprepare when
crtc is disable, until crtc is destroyed.
with this patch, hard clock will disable and unprepare
at the same time.
Signed-off-by: Yongqiang Niu <yongqiang.niu@mediatek.com>
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Signed-off-by: CK Hu <ck.hu@mediatek.com>
We met another Acer Aspire laptop which has the problem on the
headset-mic, the Pin 0x19 is not set the corret configuration for a
mic and the pin presence can't be detected too after plugging a
headset. Kailang suggested that we should set the coeff to enable the
mic and apply the ALC269_FIXUP_LIFEBOOK_EXTMIC. After doing that,
both headset-mic presence and headset-mic work well.
The existing ALC255_FIXUP_ACER_MIC_NO_PRESENCE set the headset-mic
jack to be a phantom jack. Now since the jack can support presence
unsol event, let us imporve it to set the jack to be a normal jack.
https://bugs.launchpad.net/bugs/1821269
Fixes: 5824ce8de7 ("ALSA: hda/realtek - Add support for Acer Aspire E5-475 headset mic")
Cc: Chris Chiu <chiu@endlessm.com>
CC: Daniel Drake <drake@endlessm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When a vCPU is connected to the KVM device, it is done using its vCPU
identifier in the guest. Fix the enforced limit on the vCPU identifier
by taking into account the SMT mode.
Reported-by: Satheesh Rajendran <sathnaga@linux.vnet.ibm.com>
Tested-by: Satheesh Rajendran <sathnaga@linux.vnet.ibm.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
When a CPU is hot-unplugged, the EQ is deconfigured using a zero size
and a zero address. In this case, there is no need to check the flag
and queue size validity. Move the checks after the queue reset code
section to fix CPU hot-unplug.
Reported-by: Satheesh Rajendran <sathnaga@linux.vnet.ibm.com>
Tested-by: Satheesh Rajendran <sathnaga@linux.vnet.ibm.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Improve the release of the XIVE KVM device by clearing the file
address_space, which is used to unmap the interrupt ESB pages when a
device is passed-through.
Suggested-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Currently the HV KVM code takes the kvm->lock around calls to
kvm_for_each_vcpu() and kvm_get_vcpu_by_id() (which can call
kvm_for_each_vcpu() internally). However, that leads to a lock
order inversion problem, because these are called in contexts where
the vcpu mutex is held, but the vcpu mutexes nest within kvm->lock
according to Documentation/virtual/kvm/locking.txt. Hence there
is a possibility of deadlock.
To fix this, we simply don't take the kvm->lock mutex around these
calls. This is safe because the implementations of kvm_for_each_vcpu()
and kvm_get_vcpu_by_id() have been designed to be able to be called
locklessly.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Currently the Book 3S KVM code uses kvm->lock to synchronize access
to the kvm->arch.rtas_tokens list. Because this list is scanned
inside kvmppc_rtas_hcall(), which is called with the vcpu mutex held,
taking kvm->lock cause a lock inversion problem, which could lead to
a deadlock.
To fix this, we add a new mutex, kvm->arch.rtas_token_lock, which nests
inside the vcpu mutexes, and use that instead of kvm->lock when
accessing the rtas token list.
This removes the lockdep_assert_held() in kvmppc_rtas_tokens_free().
At this point we don't hold the new mutex, but that is OK because
kvmppc_rtas_tokens_free() is only called when the whole VM is being
destroyed, and at that point nothing can be looking up a token in
the list.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Currently the HV KVM code uses kvm->lock in conjunction with a flag,
kvm->arch.mmu_ready, to synchronize MMU setup and hold off vcpu
execution until the MMU-related data structures are ready. However,
this means that kvm->lock is being taken inside vcpu->mutex, which
is contrary to Documentation/virtual/kvm/locking.txt and results in
lockdep warnings.
To fix this, we add a new mutex, kvm->arch.mmu_setup_lock, which nests
inside the vcpu mutexes, and is taken in the places where kvm->lock
was taken that are related to MMU setup.
Additionally we take the new mutex in the vcpu creation code at the
point where we are creating a new vcore, in order to provide mutual
exclusion with kvmppc_update_lpcr() and ensure that an update to
kvm->arch.lpcr doesn't get missed, which could otherwise lead to a
stale vcore->lpcr value.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Currently, kvmppc_xive_release() and kvmppc_xive_native_release() clear
kvm->arch.mmu_ready and call kick_all_cpus_sync() as a way of ensuring
that no vcpus are executing in the guest. However, future patches will
change the mutex associated with kvm->arch.mmu_ready to a new mutex that
nests inside the vcpu mutexes, making it difficult to continue to use
this method.
In fact, taking the vcpu mutex for a vcpu excludes execution of that
vcpu, and we already take the vcpu mutex around the call to
kvmppc_xive_[native_]cleanup_vcpu(). Once the cleanup function is
done and we release the vcpu mutex, the vcpu can execute once again,
but because we have cleared vcpu->arch.xive_vcpu, vcpu->arch.irq_type,
vcpu->arch.xive_esc_vaddr and vcpu->arch.xive_esc_raddr, that vcpu will
not be going into XIVE code any more. Thus, once we have cleaned up
all of the vcpus, we are safe to clean up the rest of the XIVE state,
and we don't need to use kvm->arch.mmu_ready to hold off vcpu execution.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This reverts commit 3e6a8fb330.
Cc: Andy Gross <agross@kernel.org>
Cc: David Brown <david.brown@linaro.org>
Cc: Amit Kucheria <amit.kucheria@linaro.org>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Suggested-by: Amit Kucheria <amit.kucheria@linaro.org>
Reported-by: Andy Gross <andygro@gmail.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
When CQE compression is enabled (Multi-host systems), compressed CQEs
might arrive to the driver rx, compressed CQEs don't have a valid hash
offload and the driver already reports a hash value of 0 and invalid hash
type on the skb for compressed CQEs, but this is not good enough.
On a congested PCIe, where CQE compression will kick in aggressively,
gro will deliver lots of out of order packets due to the invalid hash
and this might cause a serious performance drop.
The only valid solution, is to disable rxhash offload at all when CQE
compression is favorable (Multi-host systems).
Fixes: 7219ab34f1 ("net/mlx5e: CQE compression")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When register indr block for vlan device, it should check the real_dev
of vlan device is same as uplink device. Or it will set offload rule
to mlx5e which will never hit.
Fixes: 35a605db16 ("net/mlx5e: Offload TC e-switch rules with ingress VLAN device")
Signed-off-by: wenxu <wenxu@ucloud.cn>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
root ns is yet another fs core node which is freed using kfree() by
tree_put_node().
Rest of the other fs core objects are also allocated using kmalloc
variants.
However, root ns memory is allocated using kvzalloc().
Hence allocate root ns memory using kzalloc().
Fixes: 2530236303 ("net/mlx5_core: Flow steering tree initialization")
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
In below code flow, for ingress acl table root ns memory leads
to double free.
mlx5_init_fs
init_ingress_acls_root_ns()
init_ingress_acl_root_ns
kfree(steering->esw_ingress_root_ns);
/* steering->esw_ingress_root_ns is not marked NULL */
mlx5_cleanup_fs
cleanup_ingress_acls_root_ns
steering->esw_ingress_root_ns non NULL check passes.
kfree(steering->esw_ingress_root_ns);
/* double free */
Similar issue exist for other tables.
Hence zero out the pointers to not process the table again.
Fixes: 9b93ab981e ("net/mlx5: Separate ingress/egress namespaces for each vport")
Fixes: 40c3eebb49e51 ("net/mlx5: Add support in RDMA RX steering")
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When root ns setup for rdma, sniffer tx and sniffer rx fails,
such root ns cleanup is done by the error unwinding path of
mlx5_cleanup_fs().
Below call graph shows an example for sniffer_rx_root_ns.
mlx5_init_fs()
init_sniffer_rx_root_ns()
cleanup_root_ns(steering->sniffer_rx_root_ns);
mlx5_cleanup_fs()
cleanup_root_ns(steering->sniffer_rx_root_ns);
/* double free of sniffer_rx_root_ns */
Hence, use the existing cleanup_fs to cleanup.
Fixes: d83eb50e29 ("net/mlx5: Add support in RDMA RX steering")
Fixes: 87d22483ce ("net/mlx5: Add sniffer namespaces")
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
