Because of the missing return, the macVersion value was being
overwritten with an invalid register read
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
FCC long pulse radar (type 5) requires pulses to be
checked for chirping. This patch implements chirp
detection based on the FFT data provided for long
pulses.
A chirp is detected when a set of criteria defined
by FCC pulse characteristics is met, including
* have at least 4 FFT samples
* max_bin index moves equidistantly between samples
* the gradient is within defined range
The chirp detection has been tested with reference
radar generating devices and proved to work reliably.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The chip reports radar pulses on extension channel
even if operating in HT20 mode. This patch adds a
sanity check for HT40 mode before it feeds pulses
on extension channel to the pattern detector.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
commit 2c86c27501 ("Add ipw2100 wireless driver.") introduced
HW_PHY_OFF_LOOP_DELAY (HZ / 5000) which always evaluated to 0. Clarified
by Stanislav Yakovlev <stas.yakovlev@gmail.com> that it should be 50
milliseconds thus fixed up to msecs_to_jiffies(50).
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Acked-by: Stanislav Yakovlev <stas.yakovlev@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Concurrent AP/GO operation on different channels
isn't really supported well by the firmware so
it's better to remove it from being advertised.
Also tune the way station and p2p client interface
limits are expressed to allow station + 2x p2p
client or station + p2p client + p2p go.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Whenever any vdev was supposed to be paused all Tx
queues were stopped (except offchannel) instead of
only these associated with the given vdev.
This caused subtle issues with
multi-channel/multi-vif scenarios, e.g.
authentication of station vif could sometimes fail
depending on fw tx pause request timing.
Fixes: b4aa539dd8 ("ath10k: implement tx pause wmi event")
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Psmode can be forcefully enabled when vdev isn't
started. It isn't guaranteed that mac80211 will
re-issue psmode setting after vdev is started
unless actual bss_conf.ps value has changed.
Even if this doesn't fix any problems now it may
prevent future breakage.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The expiration function must not be called when
roc is explicitly cancelled by mac80211. However
since fcf9844636 ("ath10k: fix hw roc
expiration") the notification was never sent when
roc actually expired.
This fixes some P2P connection setup issues.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Further testing proved that multi-channel AP+STA
on QCA6174 with RM.2.0-00088 should have powersave
force-disabled to avoid beacon misses/skipping on
either side which in turn could disrupt
communication.
Since AP never has arvif->ps don't even bother
checking it. Other combinations may be broken as
well so disallow powersave with multivif outright
unless firmware advertises otherwise.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
mac80211 already does provide complete IEs for
Probe Requests for hw scan and ath10k firmware was
appending duplicate Supported Rates IEs
unnecessarily.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In commit 418ca5992e ("ath10k: Make target cpu address to
CE address conversion chip specific") mask 0x7fff is added
by mistake instead of 0x7ff. Fix this regression.
Fixes: 418ca5992e ("ath10k: Make target cpu address to CE address conversion chip specific")
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
commit a521ee983d ("ath10k: Add new reg_address/mask to hw register
table") broke QCA61x4 support by providing wrong
fw_indicator_address, which should have been 0x0003a028 instead of 0x00009028.
User experience was a failing boot up sequence (crashing device during
initialization):
[ 181.663874] ath10k_pci 0000:02:00.0: enabling device (0000 -> 0002)
[ 181.664787] ath10k_pci 0000:02:00.0: pci irq msi-x interrupts 8 irq_mode 0 reset_mode 0
[ 181.688886] ath10k_pci 0000:02:00.0: device has crashed during init
[ 181.688897] ath10k_pci 0000:02:00.0: failed to wait for target after cold reset: -70
[ 181.688902] ath10k_pci 0000:02:00.0: failed to reset chip: -70
[ 181.689774] ath10k_pci: probe of 0000:02:00.0 failed with error -70
Fix it by updating the address with correct value.
Fixes: a521ee983d ("ath10k: Add new reg_address/mask to hw register table")
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This is horribly confusing, it breaks the flow of the code without
it being apparent in the caller.
Signed-off-by: Jens Axboe <axboe@fb.com>
Acked-by: Christoph Hellwig <hch@lst.de>
It is OK for layout segments to remain hashed even if no-one holds any
references to them, provided that the segments are still valid.
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
If a process reopens the file before we can send off the CLOSE/DELEGRETURN,
then pnfs_roc_drain() may end up waiting for a new set of layout segments
that are marked as return-on-close, but haven't yet been returned.
Fix this by only waiting for those layout segments that were invalidated in
pnfs_roc().
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
If one or more of the layout segments reports an error during I/O, then
we may have to send a layoutreturn to report the error back to the NFS
metadata server.
This patch ensures that the return-on-close code can detect the
outstanding layoutreturn, and not preempt it.
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Dan reported that the recent changes to the broadcast code introduced
a potential NULL dereference.
Add the proper check.
Fixes: e045431190 "tick/broadcast: Sanity check the shutdown of the local clock_event"
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch fix a spelling typo found in API-z8530-sync-txdma-open.html.
It is because this file was generated from comment in source,
I have to fix comment in source.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reconsidering my commit 20462155 "net: inet_diag: export IPV6_V6ONLY
sockopt", I am not happy with the limitations it causes for socket
analysing code in userspace. Exporting the value only if it is set makes
it hard for userspace to decide whether the option is not set or the
kernel does not support exporting the option at all.
>From an auditor's perspective, the interesting question for listening
AF_INET6 sockets is: "Does it NOT have IPV6_V6ONLY set?" Because it is
the unexpected case. This patch allows to answer this question reliably.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sathya Perla says:
====================
be2net: patch set
Hi David, the following patch set has code cleanup patches, minor enhancements
and non-critical fixes. Pls consider applying to the net-next tree. Thanks!
Patch 1 removes duplicate code in be_setup_wol() routine making it simpler
and more readable.
Patch 2 fixes the the bridge mode return value for the ndo_bridge_getlink()
call. Instead of just relying on the SRIOV enabled state, the driver now
queries the FW, for the actual mode of bridge.
Patch 3 removes code for setting D0 power state as it's already done
in pci_enable_device()
Patch 4 fixes a bad return value in be_check_ufi_compatibility() routine
introduced by an earlier commit.
Patch 5 fixes a field in udp header being accessed while in network endian
format.
Patch 6 fixes the be_mcc_notify() routine to return an error status when
the FW/HW is in an error state.
Patch 7 fixes the be_cmd_rx_filter() routine to issue the RX_FILTER cmd
and not wait for a completion from the FW. If the FW/adapter
is in an error state, this change helps in not holding up the rtnl_lock
and keeping bottom halves disabled while the driver timesout waiting for
a response from the FW.
Patch 8 fixes the be_cmd_set_loopback() routine to issue the LOOPBACK cmd
and not wait for the FW completion while spin_lock_bh() is held on the
mcc_lock. As the cmd is always issued from ethtool in a process context,
it can sleep till the FW completion is received.
Patch 9 bumps up the driver version to 10.6.0.3
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The SET_LOOPBACK_MODE command is always issued from ethtool only in a
process context. So, while waiting for the cmd to complete, the driver
can sleep instead of holding spin_lock_bh() on the mcc_lock. This is done
by calling be_mcc_notify() instead of be_mcc_notify_wait() (that returns
only after the cmd completes while the MCCQ is locked).
Signed-off-by: Suresh Reddy <suresh.reddy@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fix makes the RX_FILTER cmd asynchronous, i.e., the caller issues
this cmd and doesn't wait for a completion from the FW. If the FW/adapter
is in an error state, this change helps in not holding up the rtnl_lock
and keeping bottom halves disabled while the driver timesout waiting for
a response from the FW.
Signed-off-by: Suresh Reddy <suresh.reddy@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the adapter is in error state, return error from be_mcc_notify()
so that the caller routines need not sleep waiting for a response.
Signed-off-by: Suresh Reddy <suresh.reddy@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "dest" field in the UDP-hdr of a TX skb is in network endian format.
Convert it to host endian before accessing it. The os2bmc patch,
mentioned below introduced this code.
Fixes: 760c295e0e ("be2net: Support for OS2BMC")
Signed-off-by: Venkat Duvvuru <VenkatKumar.Duvvuru@Emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the commit a6e6ff6eee
("be2net: simplify UFI compatibility checking"), a return value of "-1"
was incorrectly used in place of "false". This patch fixes it.
Fixes: a6e6ff6eee ("be2net: simplify UFI compatibility checking")
Signed-off-by: Vasundhara Volam <vasundhara.volam@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pci_enable_device() call sets device power state to D0; there is no need
doing it again.
Signed-off-by: Kalesh AP <kalesh.purayil@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code assumes that bridge functionality (EVB) in the adapter
is enabled only when SR-IOV is enabled. This is not always true.
This patch uses the GET_HSW_CONFIG FW cmd to query this from the FW.
Signed-off-by: Kalesh AP <kalesh.purayil@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change will make be_setup_wol() routine more compact and readable
by removing some duplicate code.
Signed-off-by: Kalesh AP <kalesh.purayil@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If outgoing interface is specified and the candidate address is
restricted to the outgoing interface, it is enough to iterate
over that given interface only.
Signed-off-by: YOSHIFUJI Hideaki <hideaki.yoshifuji@miraclelinux.com>
Acked-by: Erik Kline <ek@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
platform_driver does not need to set an owner because
platform_driver_register() will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support manually setting the polarity to mdi or mdix
Signed-off-by: David Thomson <david.thomson@alliedtelesis.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass the mdix setting from ethtool down to the phy driver, to allow
driver specific implementations of manually setting the polarity.
Signed-off-by: David Thomson <david.thomson@alliedtelesis.co.nz>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Until now when a querier was present static entries couldn't be deleted.
Fix this and allow the user to manipulate the mdb with or without a
querier.
Signed-off-by: Satish Ashok <sashok@cumulusnetworks.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Anastasov says:
====================
net: fixes for device unregistration
Test script from Eric W. Biederman can catch a problem
where packets from backlog are processed long after the last
synchronize_net call. This can be reproduced after few tests
if commit 381c759d99 ("ipv4: Avoid crashing in ip_error")
is reverted for the test. Incoming packets do not hold
reference to device but even if they do, subsystems do not
expect packets to fly during and after the NETDEV_UNREGISTER
event.
The first fix has the cost of netif_running check in fast path.
The second fix calls rcu_read_lock while local IRQ is disabled,
I hope this is not against the rules.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Incoming packet should be either in backlog queue or
in RCU read-side section. Otherwise, the final sequence of
flush_backlog() and synchronize_net() may miss packets
that can run without device reference:
CPU 1 CPU 2
skb->dev: no reference
process_backlog:__skb_dequeue
process_backlog:local_irq_enable
on_each_cpu for
flush_backlog => IPI(hardirq): flush_backlog
- packet not found in backlog
CPU delayed ...
synchronize_net
- no ongoing RCU
read-side sections
netdev_run_todo,
rcu_barrier: no
ongoing callbacks
__netif_receive_skb_core:rcu_read_lock
- too late
free dev
process packet for freed dev
Fixes: 6e583ce524 ("net: eliminate refcounting in backlog queue")
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 381c759d99 ("ipv4: Avoid crashing in ip_error")
fixes a problem where processed packet comes from device
with destroyed inetdev (dev->ip_ptr). This is not expected
because inetdev_destroy is called in NETDEV_UNREGISTER
phase and packets should not be processed after
dev_close_many() and synchronize_net(). Above fix is still
required because inetdev_destroy can be called for other
reasons. But it shows the real problem: backlog can keep
packets for long time and they do not hold reference to
device. Such packets are then delivered to upper levels
at the same time when device is unregistered.
Calling flush_backlog after NETDEV_UNREGISTER_FINAL still
accounts all packets from backlog but before that some packets
continue to be delivered to upper levels long after the
synchronize_net call which is supposed to wait the last
ones. Also, as Eric pointed out, processed packets, mostly
from other devices, can continue to add new packets to backlog.
Fix the problem by moving flush_backlog early, after the
device driver is stopped and before the synchronize_net() call.
Then use netif_running check to make sure we do not add more
packets to backlog. We have to do it in enqueue_to_backlog
context when the local IRQ is disabled. As result, after the
flush_backlog and synchronize_net sequence all packets
should be accounted.
Thanks to Eric W. Biederman for the test script and his
valuable feedback!
Reported-by: Vittorio Gambaletta <linuxbugs@vittgam.net>
Fixes: 6e583ce524 ("net: eliminate refcounting in backlog queue")
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull parisc fixes from Helge Deller:
"We have one important patch from Dave Anglin and myself which fixes
PTE/TLB race conditions which caused random segmentation faults on our
debian buildd servers, and one patch from Alex Ivanov which speeds up
the graphical text console on the STI framebuffer driver"
* 'parisc-4.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Fix some PTE/TLB race conditions and optimize __flush_tlb_range based on timing results
stifb: Implement hardware accelerated copyarea
commit 66fc130394 ("mm: shmem_zero_setup
skip security check and lockdep conflict with XFS") caused a regression
for SELinux by disabling any SELinux checking of mprotect PROT_EXEC on
shared anonymous mappings. However, even before that regression, the
checking on such mprotect PROT_EXEC calls was inconsistent with the
checking on a mmap PROT_EXEC call for a shared anonymous mapping. On a
mmap, the security hook is passed a NULL file and knows it is dealing
with an anonymous mapping and therefore applies an execmem check and no
file checks. On a mprotect, the security hook is passed a vma with a
non-NULL vm_file (as this was set from the internally-created shmem
file during mmap) and therefore applies the file-based execute check
and no execmem check. Since the aforementioned commit now marks the
shmem zero inode with the S_PRIVATE flag, the file checks are disabled
and we have no checking at all on mprotect PROT_EXEC. Add a test to
the mprotect hook logic for such private inodes, and apply an execmem
check in that case. This makes the mmap and mprotect checking
consistent for shared anonymous mappings, as well as for /dev/zero and
ashmem.
Cc: <stable@vger.kernel.org> # 4.1.x
Signed-off-by: Stephen Smalley <sds@tycho.nsa.gov>
Signed-off-by: Paul Moore <pmoore@redhat.com>
The increased use of pdtlb/pitlb instructions seemed to increase the
frequency of random segmentation faults building packages. Further, we
had a number of cases where TLB inserts would repeatedly fail and all
forward progress would stop. The Haskell ghc package caused a lot of
trouble in this area. The final indication of a race in pte handling was
this syslog entry on sibaris (C8000):
swap_free: Unused swap offset entry 00000004
BUG: Bad page map in process mysqld pte:00000100 pmd:019bbec5
addr:00000000ec464000 vm_flags:00100073 anon_vma:0000000221023828 mapping: (null) index:ec464
CPU: 1 PID: 9176 Comm: mysqld Not tainted 4.0.0-2-parisc64-smp #1 Debian 4.0.5-1
Backtrace:
[<0000000040173eb0>] show_stack+0x20/0x38
[<0000000040444424>] dump_stack+0x9c/0x110
[<00000000402a0d38>] print_bad_pte+0x1a8/0x278
[<00000000402a28b8>] unmap_single_vma+0x3d8/0x770
[<00000000402a4090>] zap_page_range+0xf0/0x198
[<00000000402ba2a4>] SyS_madvise+0x404/0x8c0
Note that the pte value is 0 except for the accessed bit 0x100. This bit
shouldn't be set without the present bit.
It should be noted that the madvise system call is probably a trigger for many
of the random segmentation faults.
In looking at the kernel code, I found the following problems:
1) The pte_clear define didn't take TLB lock when clearing a pte.
2) We didn't test pte present bit inside lock in exception support.
3) The pte and tlb locks needed to merged in order to ensure consistency
between page table and TLB. This also has the effect of serializing TLB
broadcasts on SMP systems.
The attached change implements the above and a few other tweaks to try
to improve performance. Based on the timing code, TLB purges are very
slow (e.g., ~ 209 cycles per page on rp3440). Thus, I think it
beneficial to test the split_tlb variable to avoid duplicate purges.
Probably, all PA 2.0 machines have combined TLBs.
I dropped using __flush_tlb_range in flush_tlb_mm as I realized all
applications and most threads have a stack size that is too large to
make this useful. I added some comments to this effect.
Since implementing 1 through 3, I haven't had any random segmentation
faults on mx3210 (rp3440) in about one week of building code and running
as a Debian buildd.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Cc: stable@vger.kernel.org # v3.18+
Signed-off-by: Helge Deller <deller@gmx.de>
This patch adds hardware assisted scrolling. The code is based upon the
following investigation: https://parisc.wiki.kernel.org/index.php/NGLE#Blitter
A simple 'time ls -la /usr/bin' test shows 1.6x speed increase over soft
copy and 2.3x increase over FBINFO_READS_FAST (prefer soft copy over
screen redraw) on Artist framebuffer.
Signed-off-by: Alex Ivanov <lausgans@gmail.com>
Signed-off-by: Helge Deller <deller@gmx.de>
Here's an idr memory-leak fix and a couple of new device ids.
Included is also a build fix for mos7720 on the mn10300 architecture,
which has a register with the same name as one of the driver defines.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=K/L7
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.2-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for v4.2-rc2
Here's an idr memory-leak fix and a couple of new device ids.
Included is also a build fix for mos7720 on the mn10300 architecture,
which has a register with the same name as one of the driver defines.
Signed-off-by: Johan Hovold <johan@kernel.org>
- opal-prd mmap fix from Vaidy.
- Set kernel taint for MCEs from Daniel.
- Alignment exception description from Anton.
- ppc4xx_hsta_msi build fix from Daniel
- opal-elog interrupt fix from Alistair.
- core_idle_state race fix from Shreyas.
- hv-24x7 lockdep fix from Sukadev.
- Multiple cxl fixes from Daniel, Ian, Mikey & Maninder.
- Update MAINTAINERS to point at shared tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=+CJX
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- opal-prd mmap fix from Vaidy
- set kernel taint for MCEs from Daniel
- alignment exception description from Anton
- ppc4xx_hsta_msi build fix from Daniel
- opal-elog interrupt fix from Alistair
- core_idle_state race fix from Shreyas
- hv-24x7 lockdep fix from Sukadev
- multiple cxl fixes from Daniel, Ian, Mikey & Maninder
- update MAINTAINERS to point at shared tree
* tag 'powerpc-4.2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
cxl: Check if afu is not null in cxl_slbia
powerpc: Update MAINTAINERS to point at shared tree
powerpc/perf/24x7: Fix lockdep warning
cxl: Fix off by one error allowing subsequent mmap page to be accessed
cxl: Fail mmap if requested mapping is larger than assigned problem state area
cxl: Fix refcounting in kernel API
powerpc/powernv: Fix race in updating core_idle_state
powerpc/powernv: Fix opal-elog interrupt handler
powerpc/ppc4xx_hsta_msi: Include ppc-pci.h to fix reference to hose_list
powerpc: Add plain English description for alignment exception oopses
cxl: Test the correct mmio space before unmapping
powerpc: Set the correct kernel taint on machine check errors
cxl/vphb.c: Use phb pointer after NULL check
powerpc/powernv: Fix vma page prot flags in opal-prd driver
Add support in the NFIT BLK I/O path for the "latch" flag
defined in the "Get Block NVDIMM Flags" _DSM function:
http://pmem.io/documents/NVDIMM_DSM_Interface_Example.pdf
This flag requires the driver to read back the command register after it
is written in the block I/O path. This ensures that the hardware has
fully processed the new command and moved the aperture appropriately.
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Update the nfit block I/O path to use the new PMEM API and to adhere to
the read/write flows outlined in the "NVDIMM Block Window Driver
Writer's Guide":
http://pmem.io/documents/NVDIMM_Driver_Writers_Guide.pdf
This includes adding support for targeted NVDIMM flushes called "flush
hints" in the ACPI 6.0 specification:
http://www.uefi.org/sites/default/files/resources/ACPI_6.0.pdf
For performance and media durability the mapping for a BLK aperture is
moved to a write-combining mapping which is consistent with
memcpy_to_pmem() and wmb_blk().
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
In preparation for fixing the BLK path to properly use "directed
pcommit" enable the unit test infrastructure to emit mock "flush"
tables. Writes to these flush addresses trigger a memory controller to
flush its internal buffers to persistent media, similar to the x86
"pcommit" instruction.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
