When the driver notices that PCIe link is gone by reading 0xffffffff
from a register it clears hw->hw_addr and then calls netif_device_detach().
This happens when the PCIe device is physically unplugged for example
the user disconnected the Thunderbolt cable.
However, netif_device_detach() prevents netif_unregister() from bringing
the device down properly including tearing down MSI-X vectors. This
triggers following crash during the driver removal:
igb 0000:0b:00.0 enp11s0f0: PCIe link lost, device now detached
------------[ cut here ]------------
kernel BUG at drivers/pci/msi.c:352!
invalid opcode: 0000 [#1] PREEMPT SMP PTI
...
Call Trace:
pci_disable_msix+0xc9/0xf0
igb_reset_interrupt_capability+0x58/0x60 [igb]
igb_remove+0x90/0x100 [igb]
pci_device_remove+0x31/0xa0
device_release_driver_internal+0x152/0x210
pci_stop_bus_device+0x78/0xa0
pci_stop_bus_device+0x38/0xa0
pci_stop_bus_device+0x38/0xa0
pci_stop_bus_device+0x26/0xa0
pci_stop_bus_device+0x38/0xa0
pci_stop_and_remove_bus_device+0x9/0x20
trim_stale_devices+0xee/0x130
? _raw_spin_unlock_irqrestore+0xf/0x30
trim_stale_devices+0x8f/0x130
? _raw_spin_unlock_irqrestore+0xf/0x30
trim_stale_devices+0xa1/0x130
? get_slot_status+0x8b/0xc0
acpiphp_check_bridge.part.7+0xf9/0x140
acpiphp_hotplug_notify+0x170/0x1f0
...
To prevent the crash do not call netif_device_detach() in igb_rd32().
This should be fine because hw->hw_addr is set to NULL preventing future
hardware access of the now missing device.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=198181
Reported-by: Ferenc Boldog <ferenc.boldog@gmail.com>
Reported-by: Nikolay Bogoychev <nheart@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* Add a per-VF value to know if a VF is trusted, by default don't
trust VFs.
* Implement netdev op to trust VFs (igb_ndo_set_vf_trust) and add
trust status to ndo_get_vf_config output.
* Allow a trusted VF to change MAC and MAC filters even if MAC
has been administratively set.
Signed-off-by: Corinna Vinschen <vinschen@redhat.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Kirill Tkhai says:
====================
Converting pernet_operations (part #4)
this series continues to review and to convert pernet_operations
to make them possible to be executed in parallel for several
net namespaces in the same time. The patches touch mostly netfilter,
also there are small number of changes in other places.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
These pernet_operations register and unregister sysctl.
nf_conntrack_l4proto_gre4->init_net is simple memory
initializer. Also, exit method removes gre keymap_list,
which is per-net. This looks safe to be executed
in parallel with other pernet_operations.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These pernet_operations register and unregister
two conntrack notifiers, and they seem to be safe
to be executed in parallel.
General/not related to async pernet_operations JFI:
ctnetlink_net_exit_batch() actions are grouped in batch,
and this could look like there is synchronize_rcu()
is forgotten. But there is synchronize_rcu() on module
exit patch (in ctnetlink_exit()), so this batch may
be reworked as simple .exit method.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These pernet_operations register and unregister sysctl and /proc
entries. Exit batch method also waits till all per-net conntracks
are dead. Thus, they are safe to be marked as async.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These pernet_operations initialize and destroy
net_generic(net, ip_set_net_id)-related data.
Since ip_set is under CONFIG_IP_SET, it's easy
to watch drivers, which depend on this config.
All of them are in net/netfilter/ipset directory,
except of net/netfilter/xt_set.c. There are no
more drivers, which use ip_set, and all of
the above don't register another pernet_operations.
Also, there are is no indirect users, as header
file include/linux/netfilter/ipset/ip_set.h does
not define indirect users by something like this:
#ifdef CONFIG_IP_SET
extern func(void);
#else
static inline func(void);
#endif
So, there are no more pernet operations, dereferencing
net_generic(net, ip_set_net_id).
ip_set_net_ops are OK to be executed in parallel
for several net, so we mark them as async.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These pernet_operations initialize and destroy
pernet net_generic(net, fou_net_id) list.
The rest of net_generic(net, fou_net_id) accesses
may happen after netlink message, and in-tree
pernet_operations do not send FOU_GENL_NAME messages.
So, these pernet_operations are safe to be marked
as async.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These pernet_operations looks similar to dccp_v4_ops,
and they are also safe to be marked as async.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These pernet_operations create and destroy net::dccp::v4_ctl_sk.
It looks like another pernet_operations don't want to send
dccp packets to dying or creating net. Batch method similar
to ipv4/ipv6 sockets and it has to be safe to be executed
in parallel with anything else. So, we mark them as async.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These pernet_operations have a deal with cgw_list,
and the rest of accesses are made under rtnl_lock().
The only exception is cgw_dump_jobs(), which is
accessed under rcu_read_lock(). cgw_dump_jobs() is
called on netlink request, and it does not seem,
foreign pernet_operations want to send a net such
the messages. So, we mark them as async.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Init method just allocates memory for new cfg, and
assigns net_generic(net, caif_net_id). Despite there is
synchronize_rcu() on error path in cfcnfg_create(),
in real this function does not use global lists,
so it looks like this synchronize_rcu() is some legacy
inheritance. Exit method removes caif devices under
rtnl_lock().
There could be a problem, if someone from foreign net
pernet_operations dereference caif_net_id of this net.
It's dereferenced in get_cfcnfg() and caif_device_list().
get_cfcnfg() is used from netdevice notifiers, where
they are called under rtnl_lock(). The notifiers can't
be called from foreign nets pernet_operations. Also,
it's used from caif_disconnect_client() and from
caif_connect_client(). The both of the functions work
with caif socket, and there is the only possibility
to have a socket, when the net is dead. This may happen
only of the socket was created as kern using sk_alloc().
Grep by PF_CAIF shows we do not create kern caif sockets,
so get_cfcnfg() is safe.
caif_device_list() is used in netdevice notifiers and exit
method under rtnl lock. Also, from caif_get() used in
the netdev notifiers and in caif_flow_cb(). The last item
is skb destructor. Since there are no kernel caif sockets
nobody can send net a packet in parallel with init/exit,
so this is also safe.
So, these pernet_operations are safe to be async.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These pernet_operations call xt_proto_init() and xt_proto_fini(),
which just register and unregister /proc entries.
They are safe to be marked as async.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These pernet_operations use nf_log_set() and nf_log_unset()
in their methods:
nf_log_bridge_net_ops
nf_log_arp_net_ops
nf_log_ipv4_net_ops
nf_log_ipv6_net_ops
nf_log_netdev_net_ops
Nobody can send such a packet to a net before it's became
registered, nobody can send a packet after all netdevices
are unregistered. So, these pernet_operations are able
to be marked as async.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These pernet_operations use ebt_register_table() and
ebt_unregister_table() to act on the tables, which
are used as argument in ebt_do_table(), called from
ebtables hooks.
Since there are no net-related bridge packets in-flight,
when the init and exit methods are called, these
pernet_operations are safe to be executed in parallel
with any other.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For tests using veth interfaces, the test infrastructure can create
the netdevs if they do not exist. Arguably this is a preferred approach
since the tests require p$N and p$(N+1) to be pairs.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a generic netlink family for NCSI. This supports three commands;
NCSI_CMD_PKG_INFO which returns information on packages and their
associated channels, NCSI_CMD_SET_INTERFACE which allows a specific
package or package/channel combination to be set as the preferred
choice, and NCSI_CMD_CLEAR_INTERFACE which clears any preferred setting.
Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds TCP_NLA_CA_STATE stat into SCM_TIMESTAMPING_OPT_STATS.
It reports ca_state of socket, when timestamp is generated.
Signed-off-by: Priyaranjan Jha <priyarjha@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds TCP_NLA_SENDQ_SIZE stat into SCM_TIMESTAMPING_OPT_STATS.
It reports no. of bytes present in send queue, when timestamp is
generated.
Signed-off-by: Priyaranjan Jha <priyarjha@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the tc action test is used only to test mirred redirect
action. This patch extends it for mirred mirror.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
LRO and RX-FCS offloads cannot be enabled at the same time since it is
not clear what should happen to the FCS of each coalesced packet.
The FCS is not really part of the TCP payload, hence cannot be merged
into one big packet. On the other hand, providing one big LRO packet
with one FCS contradicts the RX-FCS feature goal.
Use the fix features mechanism in order to prevent intersection of the
features and drop LRO in case RX-FCS is requested.
Enabling RX-FCS while LRO is enabled will result in:
$ ethtool -K ens6 rx-fcs on
Actual changes:
large-receive-offload: off [requested on]
rx-fcs: on
Signed-off-by: Gal Pressman <galp@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Corrected stats mismatch between Host Tx and its peer Rx stats
Signed-off-by: Intiyaz Basha <intiyaz.basha@cavium.com>
Acked-by: Derek Chickles <derek.chickles@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The changes in dd84441a79 ("x86/speculation: Use IBRS if available
before calling into firmware") don't need any kind of special treatment
in the current tools/perf/ codebase, so just update the copy to get rid
of the perf build warning:
BUILD: Doing 'make -j4' parallel build
Warning: Kernel ABI header at 'tools/arch/x86/include/asm/cpufeatures.h' differs from latest version at 'arch/x86/include/asm/cpufeatures.h'
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: David Woodhouse <dwmw@amazon.co.uk>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: https://lkml.kernel.org/n/tip-mzmuxocrf96v922xkerey3ns@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Currently we can crash perf record when running in pipe mode, like:
$ perf record ls | perf report
# To display the perf.data header info, please use --header/--header-only options.
#
perf: Segmentation fault
Error:
The - file has no samples!
The callstack of the crash is:
0x0000000000515242 in perf_event__synthesize_event_update_name
3513 ev = event_update_event__new(len + 1, PERF_EVENT_UPDATE__NAME, evsel->id[0]);
(gdb) bt
#0 0x0000000000515242 in perf_event__synthesize_event_update_name
#1 0x00000000005158a4 in perf_event__synthesize_extra_attr
#2 0x0000000000443347 in record__synthesize
#3 0x00000000004438e3 in __cmd_record
#4 0x000000000044514e in cmd_record
#5 0x00000000004cbc95 in run_builtin
#6 0x00000000004cbf02 in handle_internal_command
#7 0x00000000004cc054 in run_argv
#8 0x00000000004cc422 in main
The reason of the crash is that the evsel does not have ids array
allocated and the pipe's synthesize code tries to access it.
We don't force evsel ids allocation when we have single event, because
it's not needed. However we need it when we are in pipe mode even for
single event as a key for evsel update event.
Fixing this by forcing evsel ids allocation event for single event, when
we are in pipe mode.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20180302161354.30192-1-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
This first happened with a gcc function, _cpp_lex_token, that has the
usual jumps:
│1159e6c: ↓ jne 115aa32 <_cpp_lex_token@@Base+0xf92>
I.e. jumps to a label inside that function (_cpp_lex_token), and those
works, but also this kind:
│1159e8b: ↓ jne c469be <cpp_named_operator2name@@Base+0xa72>
I.e. jumps to another function, outside _cpp_lex_token, which are not
being correctly handled generating as a side effect references to
ab->offset[] entries that are set to NULL, so to make this code more
robust, check that here.
A proper fix for will be put in place, looking at the function name
right after the '<' token and probably treating this like a 'call'
instruction.
For now just don't draw the arrow.
Reported-by: Ingo Molnar <mingo@kernel.org>
Tested-by: Ingo Molnar <mingo@kernel.org>
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Wang Nan <wangnan0@huawei.com>
Cc: Jin Yao <yao.jin@intel.com>
Cc: Kan Liang <kan.liang@intel.com>
Link: https://lkml.kernel.org/n/tip-5tzvb875ep2sel03aeefgmud@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
On older (e.g. v4.4) kernels, an annoying fallback message can be
observed in 'perf top':
┌─Warning:──────────────────────┐
│fall back to non-overwrite mode│
│ │
│ │
│Press any key... │
└───────────────────────────────┘
The 'perf top' utility has been changed to overwrite mode since commit
ebebbf0823 ("perf top: Switch default mode to overwrite mode").
For older kernels which don't have overwrite mode support, 'perf top'
will fall back to non-overwrite mode and print out the fallback message
using ui__warning(), which needs user's input to close.
The fallback message is not critical for end users. Turning it to debug
message which is printed when running with -vv.
Reported-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Kan Liang <kan.liang@intel.com>
Cc: Kan Liang <kan.liang@intel.com>
Fixes: ebebbf0823 ("perf top: Switch default mode to overwrite mode")
Link: http://lkml.kernel.org/r/1519669030-176549-1-git-send-email-kan.liang@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
First, all man pages highlight only perf and subcommands except 'perf
kallsyms', which includes the full usage. Fix it for commands to
monopolize underlines.
Second, options can be ommited when executing 'perf kallsyms', so add
square brackets between <option>.
Signed-off-by: Sangwon Hong <qpakzk@gmail.com>
Acked-by: Namhyung Kim <namhyung@kernel.org>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Taeung Song <treeze.taeung@gmail.com>
Link: http://lkml.kernel.org/r/1518377864-20353-1-git-send-email-qpakzk@gmail.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
kconfig.h was excluded from consideration by fixdep by
6a5be57f0f (fixdep: fix extraneous dependencies) to avoid some false
positive hits
(1) include/config/.h
(2) include/config/h.h
(3) include/config/foo.h
(1) occurred because kconfig.h contains the string CONFIG_ in a
comment. However, since dee81e9886 (fixdep: faster CONFIG_ search), we
have a check that the part after CONFIG_ is non-empty, so this does not
happen anymore (and CONFIG_ appears by itself elsewhere, so that check
is worthwhile).
(2) comes from the include guard, __LINUX_KCONFIG_H. But with the
previous patch, we no longer match that either.
That leaves (3), which amounts to one [1] false dependency (aka stat() call
done by make), which I think we can live with:
We've already had one case [2] where the lack of include/linux/kconfig.h in
the .o.cmd file caused a missing rebuild, and while I originally thought
we should just put kconfig.h in the dependency list without parsing it
for the CONFIG_ pattern, we actually do have some real CONFIG_ symbols
mentioned in it, and one can imagine some translation unit that just
does '#ifdef __BIG_ENDIAN' but doesn't through some other header
actually depend on CONFIG_CPU_BIG_ENDIAN - so changing the target
endianness could end up rebuilding the world, minus that small
TU. Quoting Linus,
... when missing dependencies cause a missed re-compile, the resulting
bugs can be _really_ subtle.
[1] well, two, we now also have CONFIG_BOOGER/booger.h - we could change
that to FOO if we care
[2] https://lkml.org/lkml/2018/2/22/838
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The string CONFIG_ quite often appears after other alphanumerics,
meaning that that instance cannot be referencing a Kconfig
symbol. Omitting these means make has fewer files to stat() when
deciding what needs to be rebuilt - for a defconfig build, this seems to
remove about 2% of the (wildcard ...) lines from the .o.cmd files.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
uml-config.h hasn't existed in this decade (87e299e5c7 - x86, um: get
rid of uml-config.h). The few remaining UML_CONFIG instances are defined
directly in terms of their real CONFIG symbol in common-offsets.h, so
unlike when the symbols got defined via a sed script, anything that uses
UML_CONFIG_FOO now should also automatically pick up a dependency on
CONFIG_FOO via the normal fixdep mechanism (since common-offsets.h
should at least recursively be a dependency). Hence I believe we should
actually be able to ignore the HELLO_CONFIG_BOOM cases.
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Richard Weinberger <richard@nod.at>
Cc: user-mode-linux-devel@lists.sourceforge.net
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Commit 7a407aa5e0 ("MIPS: Push ARCH_MIGHT_HAVE_PC_SERIO down to
platform level") moves the global MIPS ARCH_MIGHT_HAVE_PC_SERIO select
down to various platforms, but doesn't add it to Loongson64 platforms
which need it, so add the selects to these platforms too.
Fixes: 7a407aa5e0 ("MIPS: Push ARCH_MIGHT_HAVE_PC_SERIO down to platform level")
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/18704/
Signed-off-by: James Hogan <jhogan@kernel.org>
Commit a211a0820d ("MIPS: Push ARCH_MIGHT_HAVE_PC_PARPORT down to
platform level") moves the global MIPS ARCH_MIGHT_HAVE_PC_PARPORT select
down to various platforms, but doesn't add it to Loongson64 platforms
which need it, so add the selects to these platforms too.
Fixes: a211a0820d ("MIPS: Push ARCH_MIGHT_HAVE_PC_PARPORT down to platform level")
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/18703/
Signed-off-by: James Hogan <jhogan@kernel.org>
This patch fixes compatible for STM32F7 USB OTG HS and consistently rename
dw2_set_params function.
The v2 former patch [1] had been acked by Paul Young, but v1 was merged.
[1] https://patchwork.kernel.org/patch/9925573/
Fixes: d8fae8b936 ("usb: dwc2: add support for STM32F7xx USB OTG HS")
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch fixes binding documentation for DWC2 controller in HS mode
found on STMicroelectronics STM32F7 SoC.
The v2 former patch [1] had been acked by Rob Herring, but v1 was merged.
[1] https://patchwork.kernel.org/patch/9925575/
Fixes: 000777dadc ("dt-bindings: usb: Document the STM32F7xx DWC2 ...")
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When I debug a kernel crash issue in funcitonfs, found ffs_data.ref
overflowed, While functionfs is unmounting, ffs_data is put twice.
Commit 43938613c6 ("drivers, usb: convert ffs_data.ref from atomic_t to
refcount_t") can avoid refcount overflow, but that is risk some situations.
So no need put ffs data in ffs_fs_kill_sb, already put in ffs_data_closed.
The issue can be reproduced in Mediatek mt6763 SoC, ffs for ADB device.
KASAN enabled configuration reports use-after-free errro.
BUG: KASAN: use-after-free in refcount_dec_and_test+0x14/0xe0 at addr ffffffc0579386a0
Read of size 4 by task umount/4650
====================================================
BUG kmalloc-512 (Tainted: P W O ): kasan: bad access detected
-----------------------------------------------------------------------------
INFO: Allocated in ffs_fs_mount+0x194/0x844 age=22856 cpu=2 pid=566
alloc_debug_processing+0x1ac/0x1e8
___slab_alloc.constprop.63+0x640/0x648
__slab_alloc.isra.57.constprop.62+0x24/0x34
kmem_cache_alloc_trace+0x1a8/0x2bc
ffs_fs_mount+0x194/0x844
mount_fs+0x6c/0x1d0
vfs_kern_mount+0x50/0x1b4
do_mount+0x258/0x1034
INFO: Freed in ffs_data_put+0x25c/0x320 age=0 cpu=3 pid=4650
free_debug_processing+0x22c/0x434
__slab_free+0x2d8/0x3a0
kfree+0x254/0x264
ffs_data_put+0x25c/0x320
ffs_data_closed+0x124/0x15c
ffs_fs_kill_sb+0xb8/0x110
deactivate_locked_super+0x6c/0x98
deactivate_super+0xb0/0xbc
INFO: Object 0xffffffc057938600 @offset=1536 fp=0x (null)
......
Call trace:
[<ffffff900808cf5c>] dump_backtrace+0x0/0x250
[<ffffff900808d3a0>] show_stack+0x14/0x1c
[<ffffff90084a8c04>] dump_stack+0xa0/0xc8
[<ffffff900826c2b4>] print_trailer+0x158/0x260
[<ffffff900826d9d8>] object_err+0x3c/0x40
[<ffffff90082745f0>] kasan_report_error+0x2a8/0x754
[<ffffff9008274f84>] kasan_report+0x5c/0x60
[<ffffff9008273208>] __asan_load4+0x70/0x88
[<ffffff90084cd81c>] refcount_dec_and_test+0x14/0xe0
[<ffffff9008d98f9c>] ffs_data_put+0x80/0x320
[<ffffff9008d9d904>] ffs_fs_kill_sb+0xc8/0x110
[<ffffff90082852a0>] deactivate_locked_super+0x6c/0x98
[<ffffff900828537c>] deactivate_super+0xb0/0xbc
[<ffffff90082af0c0>] cleanup_mnt+0x64/0xec
[<ffffff90082af1b0>] __cleanup_mnt+0x10/0x18
[<ffffff90080d9e68>] task_work_run+0xcc/0x124
[<ffffff900808c8c0>] do_notify_resume+0x60/0x70
[<ffffff90080866e4>] work_pending+0x10/0x14
Cc: stable@vger.kernel.org
Signed-off-by: Xinyong <xinyong.fang@linux.alibaba.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The commit 9d9491a7da ("mmc: dw_mmc: Fix the DTO timeout calculation")
and commit 4c2357f57d ("mmc: dw_mmc: Fix the CTO timeout calculation")
made changes, which cause multiply overflow for 32-bit systems. The broken
timeout calculations leads to unexpected ETIMEDOUT errors and causes
stacktrace splat (such as below) during normal data exchange with SD-card.
| Running : 4M-check-reassembly-tcp-cmykw2-rotatew2.out -v0 -w1
| - Info: Finished target initialization.
| mmcblk0: error -110 transferring data, sector 320544, nr 2048, cmd
| response 0x900, card status 0x0
DIV_ROUND_UP_ULL helps to escape usage of __udivdi3() from libgcc and so
code gets compiled on all 32-bit platforms as opposed to usage of
DIV_ROUND_UP when we may only compile stuff on a very few arches.
Lets cast this multiply to u64 type to prevent the overflow.
Fixes: 9d9491a7da ("mmc: dw_mmc: Fix the DTO timeout calculation")
Fixes: 4c2357f57d ("mmc: dw_mmc: Fix the CTO timeout calculation")
Tested-by: Vineet Gupta <Vineet.Gupta1@synopsys.com>
Reported-by: Vineet Gupta <Vineet.Gupta1@synopsys.com> # ARC STAR 9001306872 HSDK, sdio: board crashes when copying big files
Signed-off-by: Evgeniy Didin <Evgeniy.Didin@synopsys.com>
Cc: <stable@vger.kernel.org> # 4.14
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Since commit ab82fa7da4 ("gpio: rcar: Prevent module clock disable
when wake-up is enabled"), when a GPIO is used for wakeup, the GPIO
block's module clock (if exists) is manually kept running during system
suspend, to make sure the device stays active.
However, this explicit clock handling is merely a workaround for a
failure to properly communicate wakeup information to the device core.
Instead, set the device's power.wakeup_path field, to indicate this
device is part of the wakeup path. Depending on the PM Domain's
active_wakeup configuration, the genpd core code will keep the device
enabled (and the clock running) during system suspend when needed.
This allows for the removal of all explicit clock handling code from the
driver.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Stephen Hemminger says:
====================
hv_netvsc: minor fixes
These are improvements to netvsc driver. They aren't functionality
changes so not targeting net-next; and they are not show stopper
bugs that need to go to stable either.
v2
- drop the irq flags patch, defer it to net-next
- split the multicast filter flag patch out
- change propogate rx mode patch to handle startup of vf
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The netvsc device should propagate filters to the SR-IOV VF
device (if present). The flags also need to be propagated to the
VF device as well. This only really matters on local Hyper-V
since Azure does not support multiple addresses.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netvsc driver was always enabling all multicast and broadcast
even if netdevice flag had not enabled it.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When VF is used for accelerated networking it will likely have
more queues (and different policy) than the synthetic NIC.
This patch defers the queue policy to the VF so that all the
queues can be used. This impacts workloads like local generate UDP.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the netvsc_channel_cb is already called in interrupt
context from vmbus, there is no need to do irqsave/restore.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a race between napi_reschedule and re-enabling interrupts
which could lead to missed host interrrupts. This occurs when
interrupts are re-enabled (hv_end_read) and vmbus irq callback
(netvsc_channel_cb) has already scheduled NAPI.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Block setup of multiple channels earlier in the teardown
process. This avoids possible races between halt and subchannel
initialization.
Suggested-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Need to delete NAPI association if vmbus_open fails.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't wake transmit queues if link is not up yet.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
