s390 does not map the vdso for statically linked binaries, assuming
that this doesn't make sense. See commit fc5243d98a ("[S390]
arch_setup_additional_pages arguments").
However with glibc commit d665367f596d ("linux: Enable vDSO for static
linking as default (BZ#19767)") and commit 5e855c895401 ("s390: Enable
VDSO for static linking") the vdso is also used for statically linked
binaries - if the kernel would make it available.
Therefore map the vdso always, just like all other architectures.
Reported-by: Stefan Liebler <[email protected]>
Signed-off-by: Heiko Carstens <[email protected]>
Signed-off-by: Vasily Gorbik <[email protected]>
A HW mapped level sensitive interrupt asserted by a device will not be put
into the ap_list if it is disabled at the VGIC level. When it is enabled
again, it will be inserted into the ap_list and written to a list register
on guest entry regardless of the state of the device.
We could argue that this can also happen on real hardware, when the command
to enable the interrupt reached the GIC before the device had the chance to
de-assert the interrupt signal; however, we emulate the distributor and
redistributors in software and we can do better than that.
Signed-off-by: Alexandru Elisei <[email protected]>
Signed-off-by: Marc Zyngier <[email protected]>
At the moment, the way we reset CP15 registers is mildly insane:
We write junk to them, call the reset functions, and then check that
we have something else in them.
The "fun" thing is that this can happen while the guest is running
(PSCI, for example). If anything in KVM has to evaluate the state
of a CP15 register while junk is in there, bad thing may happen.
Let's stop doing that. Instead, we track that we have called a
reset function for that register, and assume that the reset
function has done something.
In the end, the very need of this reset check is pretty dubious,
as it doesn't check everything (a lot of the CP15 reg leave outside
of the cp15_regs[] array). It may well be axed in the near future.
Signed-off-by: Marc Zyngier <[email protected]>
At the moment, the way we reset system registers is mildly insane:
We write junk to them, call the reset functions, and then check that
we have something else in them.
The "fun" thing is that this can happen while the guest is running
(PSCI, for example). If anything in KVM has to evaluate the state
of a system register while junk is in there, bad thing may happen.
Let's stop doing that. Instead, we track that we have called a
reset function for that register, and assume that the reset
function has done something. This requires fixing a couple of
sysreg refinition in the trap table.
In the end, the very need of this reset check is pretty dubious,
as it doesn't check everything (a lot of the sysregs leave outside of
the sys_regs[] array). It may well be axed in the near future.
Tested-by: Zenghui Yu <[email protected]>
Signed-off-by: Marc Zyngier <[email protected]>
This should never have landed in the first place: it was added as part
of 64-bit divide support for 32-bit systems, but the kernel doesn't
allow this sort of division. I must have forgotten to remove it.
This patch removes the support. Since this routine only worked on
64-bit platforms but was only built on 32-bit platforms, it's
essentially just nonsense anyway.
Signed-off-by: Palmer Dabbelt <[email protected]>
Acked-by: Nicolas Pitre <[email protected]>
Link: https://lore.kernel.org/linux-riscv/[email protected]/T/#t
Reported-by: Eric Lin <[email protected]>
Signed-off-by: Paul Walmsley <[email protected]>
In preparation for removing __udivdi3() from the RISC-V
architecture-specific files, convert its one user to use do_div().
This avoids breaking the RV32 build after __udivdi3() is removed.
This second version removes the assignment of the remainder to an
unused temporary variable. Thanks to Nicolas Pitre <[email protected]>
for the suggestion.
Signed-off-by: Paul Walmsley <[email protected]>
Cc: Nicolas Pitre <[email protected]>
Since the RISC-V specification states that ISA description strings are
case-insensitive, there's no functional difference between mixed-case,
upper-case, and lower-case ISA strings. Thus, to simplify parsing,
specify that the letters present in "riscv,isa" must be all lowercase.
Suggested-by: Paul Walmsley <[email protected]>
Signed-off-by: Atish Patra <[email protected]>
Signed-off-by: Paul Walmsley <[email protected]>
Highlights include:
Stable fixes:
- NFSv4: Ensure we check the return value of update_open_stateid() so we
correctly track active open state.
- NFSv4: Fix for delegation state recovery to ensure we recover all open
modes that are active.
- NFSv4: Fix an Oops in nfs4_do_setattr
Bugfixes:
- NFS: Fix regression whereby fscache errors are appearing on 'nofsc' mounts
- NFSv4: Fix a potential sleep while atomic in nfs4_do_reclaim()
- NFSv4: Fix a credential refcount leak in nfs41_check_delegation_stateid
- pNFS: Report errors from the call to nfs4_select_rw_stateid()
- NFSv4: Various other delegation and open stateid recovery fixes
- NFSv4: Fix state recovery behaviour when server connection times out
-----BEGIN PGP SIGNATURE-----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=IXqc
-----END PGP SIGNATURE-----
Merge tag 'nfs-for-5.3-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client fixes from Trond Myklebust:
"Highlights include:
Stable fixes:
- NFSv4: Ensure we check the return value of update_open_stateid() so
we correctly track active open state.
- NFSv4: Fix for delegation state recovery to ensure we recover all
open modes that are active.
- NFSv4: Fix an Oops in nfs4_do_setattr
Fixes:
- NFS: Fix regression whereby fscache errors are appearing on 'nofsc'
mounts
- NFSv4: Fix a potential sleep while atomic in nfs4_do_reclaim()
- NFSv4: Fix a credential refcount leak in nfs41_check_delegation_stateid
- pNFS: Report errors from the call to nfs4_select_rw_stateid()
- NFSv4: Various other delegation and open stateid recovery fixes
- NFSv4: Fix state recovery behaviour when server connection times
out"
* tag 'nfs-for-5.3-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
NFSv4: Ensure state recovery handles ETIMEDOUT correctly
NFS: Fix regression whereby fscache errors are appearing on 'nofsc' mounts
NFSv4: Fix an Oops in nfs4_do_setattr
NFSv4: Fix a potential sleep while atomic in nfs4_do_reclaim()
NFSv4: Check the return value of update_open_stateid()
NFSv4.1: Only reap expired delegations
NFSv4.1: Fix open stateid recovery
NFSv4: Report the error from nfs4_select_rw_stateid()
NFSv4: When recovering state fails with EAGAIN, retry the same recovery
NFSv4: Print an error in the syslog when state is marked as irrecoverable
NFSv4: Fix delegation state recovery
NFSv4: Fix a credential refcount leak in nfs41_check_delegation_stateid
db-export:
Adrian Hunter:
- Fix thread__exec_comm() picking of main thread COMM for pre-existing,
synthesized from /proc data records.
annotate:
Arnaldo Carvalho de Melo:
- Fix printing of unaugmented disassembled instructions from BPF, some
lines were leaving leftovers from the previous screen, due to use of
newlines by binutils's libopcode disassembler.
perf ftrace:
He Zhe:
- Fix cpumask problems when only one CPU is present.
PMU events:
Jin Yao:
- Add missing "cpu_clk_unhalted.core" event.
perf bench:
Jiri Olsa:
- Fix cpu0 binding in the NUMA benchmarks.
s390:
Thomas Richter:
- Fix module size calculations.
build system:
Masanari Iida:
- Fix a typo in a variable name in the Documentation Makefile
misc:
Ian Rogers:
- Fix include paths in ui directory.
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQR2GiIUctdOfX2qHhGyPKLppCJ+JwUCXUxu6gAKCRCyPKLppCJ+
J3aBAQDRhogUJcsWbDlEE0lnWoSLyxh5Q0uDbtsF+wwL8kwFjAD+Ne9VDyaa36ay
xRydbjQmxMXCvOWkJcHWCx/JEDGkFg4=
=bi5a
-----END PGP SIGNATURE-----
Merge tag 'perf-urgent-for-mingo-5.3-20190808' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/urgent
perf/urgent fixes:
db-export:
Adrian Hunter:
- Fix thread__exec_comm() picking of main thread COMM for pre-existing,
synthesized from /proc data records.
annotate:
Arnaldo Carvalho de Melo:
- Fix printing of unaugmented disassembled instructions from BPF, some
lines were leaving leftovers from the previous screen, due to use of
newlines by binutils's libopcode disassembler.
perf ftrace:
He Zhe:
- Fix cpumask problems when only one CPU is present.
PMU events:
Jin Yao:
- Add missing "cpu_clk_unhalted.core" event.
perf bench:
Jiri Olsa:
- Fix cpu0 binding in the NUMA benchmarks.
s390:
Thomas Richter:
- Fix module size calculations.
build system:
Masanari Iida:
- Fix a typo in a variable name in the Documentation Makefile
misc:
Ian Rogers:
- Fix include paths in ui directory.
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
The events defined in pmu-events JSON are parsed and added into perf
tool. For fixed counters, we handle the encodings between JSON and perf
by using a static array fixed[].
But the fixed[] has missed an important event "cpu_clk_unhalted.core".
For example, on the Tremont platform,
[root@localhost ~]# perf stat -e cpu_clk_unhalted.core -a
event syntax error: 'cpu_clk_unhalted.core'
\___ parser error
With this patch, the event cpu_clk_unhalted.core can be parsed.
[root@localhost perf]# ./perf stat -e cpu_clk_unhalted.core -a -vvv
------------------------------------------------------------
perf_event_attr:
type 4
size 112
config 0x3c
sample_type IDENTIFIER
read_format TOTAL_TIME_ENABLED|TOTAL_TIME_RUNNING
disabled 1
inherit 1
exclude_guest 1
------------------------------------------------------------
...
Signed-off-by: Jin Yao <[email protected]>
Cc: Alexander Shishkin <[email protected]>
Cc: Andi Kleen <[email protected]>
Cc: Jin Yao <[email protected]>
Cc: Jiri Olsa <[email protected]>
Cc: Kan Liang <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
During execution of command 'perf top' the error message:
Not enough memory for annotating '__irf_end' symbol!)
is emitted from this call sequence:
__cmd_top
perf_top__mmap_read
perf_top__mmap_read_idx
perf_event__process_sample
hist_entry_iter__add
hist_iter__top_callback
perf_top__record_precise_ip
hist_entry__inc_addr_samples
symbol__inc_addr_samples
symbol__get_annotation
symbol__alloc_hist
In this function the size of symbol __irf_end is calculated. The size of
a symbol is the difference between its start and end address.
When the symbol was read the first time, its start and end was set to:
symbol__new: __irf_end 0xe954d0-0xe954d0
which is correct and maps with /proc/kallsyms:
root@s8360046:~/linux-4.15.0/tools/perf# fgrep _irf_end /proc/kallsyms
0000000000e954d0 t __irf_end
root@s8360046:~/linux-4.15.0/tools/perf#
In function symbol__alloc_hist() the end of symbol __irf_end is
symbol__alloc_hist sym:__irf_end start:0xe954d0 end:0x3ff80045a8
which is identical with the first module entry in /proc/kallsyms
This results in a symbol size of __irf_req for histogram analyses of
70334140059072 bytes and a malloc() for this requested size fails.
The root cause of this is function
__dso__load_kallsyms()
+-> symbols__fixup_end()
Function symbols__fixup_end() enlarges the last symbol in the kallsyms
map:
# fgrep __irf_end /proc/kallsyms
0000000000e954d0 t __irf_end
#
to the start address of the first module:
# cat /proc/kallsyms | sort | egrep ' [tT] '
....
0000000000e952d0 T __security_initcall_end
0000000000e954d0 T __initramfs_size
0000000000e954d0 t __irf_end
000003ff800045a8 T fc_get_event_number [scsi_transport_fc]
000003ff800045d0 t store_fc_vport_disable [scsi_transport_fc]
000003ff800046a8 T scsi_is_fc_rport [scsi_transport_fc]
000003ff800046d0 t fc_target_setup [scsi_transport_fc]
On s390 the kernel is located around memory address 0x200, 0x10000 or
0x100000, depending on linux version. Modules however start some- where
around 0x3ff xxxx xxxx.
This is different than x86 and produces a large gap for which histogram
allocation fails.
Fix this by detecting the kernel's last symbol and do no adjustment for
it. Introduce a weak function and handle s390 specifics.
Reported-by: Klaus Theurich <[email protected]>
Signed-off-by: Thomas Richter <[email protected]>
Acked-by: Heiko Carstens <[email protected]>
Cc: Hendrik Brueckner <[email protected]>
Cc: Vasily Gorbik <[email protected]>
Cc: [email protected]
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
On s390 the modules loaded in memory have the text segment located after
the GOT and Relocation table. This can be seen with this output:
[root@m35lp76 perf]# fgrep qeth /proc/modules
qeth 151552 1 qeth_l2, Live 0x000003ff800b2000
...
[root@m35lp76 perf]# cat /sys/module/qeth/sections/.text
0x000003ff800b3990
[root@m35lp76 perf]#
There is an offset of 0x1990 bytes. The size of the qeth module is
151552 bytes (0x25000 in hex).
The location of the GOT/relocation table at the beginning of a module is
unique to s390.
commit 203d8a4aa6 ("perf s390: Fix 'start' address of module's map")
adjusts the start address of a module in the map structures, but does
not adjust the size of the modules. This leads to overlapping of module
maps as this example shows:
[root@m35lp76 perf] # ./perf report -D
0 0 0xfb0 [0xa0]: PERF_RECORD_MMAP -1/0: [0x3ff800b3990(0x25000)
@ 0]: x /lib/modules/.../qeth.ko.xz
0 0 0x1050 [0xb0]: PERF_RECORD_MMAP -1/0: [0x3ff800d85a0(0x8000)
@ 0]: x /lib/modules/.../ip6_tables.ko.xz
The module qeth.ko has an adjusted start address modified to b3990, but
its size is unchanged and the module ends at 0x3ff800d8990. This end
address overlaps with the next modules start address of 0x3ff800d85a0.
When the size of the leading GOT/Relocation table stored in the
beginning of the text segment (0x1990 bytes) is subtracted from module
qeth end address, there are no overlaps anymore:
0x3ff800d8990 - 0x1990 = 0x0x3ff800d7000
which is the same as
0x3ff800b2000 + 0x25000 = 0x0x3ff800d7000.
To fix this issue, also adjust the modules size in function
arch__fix_module_text_start(). Add another function parameter named size
and reduce the size of the module when the text segment start address is
changed.
Output after:
0 0 0xfb0 [0xa0]: PERF_RECORD_MMAP -1/0: [0x3ff800b3990(0x23670)
@ 0]: x /lib/modules/.../qeth.ko.xz
0 0 0x1050 [0xb0]: PERF_RECORD_MMAP -1/0: [0x3ff800d85a0(0x7a60)
@ 0]: x /lib/modules/.../ip6_tables.ko.xz
Reported-by: Stefan Liebler <[email protected]>
Signed-off-by: Thomas Richter <[email protected]>
Acked-by: Heiko Carstens <[email protected]>
Cc: Hendrik Brueckner <[email protected]>
Cc: Vasily Gorbik <[email protected]>
Cc: [email protected]
Fixes: 203d8a4aa6 ("perf s390: Fix 'start' address of module's map")
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
The code to disassemble BPF programs uses binutil's disassembling
routines, and those use in turn fprintf to print to a memstream FILE,
adding a newline at the end of each line, which ends up confusing the
TUI routines called from:
annotate_browser__write()
annotate_line__write()
annotate_browser__printf()
ui_browser__vprintf()
SLsmg_vprintf()
The SLsmg_vprintf() function in the slang library gets confused with the
terminating newline, so make the disasm_line__parse() function that
parses the lines produced by the BPF specific disassembler (that uses
binutil's libopcodes) and the lines produced by the objdump based
disassembler used for everything else (and that doesn't adds this
terminating newline) trim the end of the line in addition of the
beginning.
This way when disasm_line->ops.raw, i.e. for instructions without a
special scnprintf() method, we'll not have that \n getting in the way of
filling the screen right after the instruction with spaces to avoid
leaving what was on the screen before and thus garbling the annotation
screen, breaking scrolling, etc.
Cc: Adrian Hunter <[email protected]>
Cc: Jiri Olsa <[email protected]>
Cc: Namhyung Kim <[email protected]>
Cc: Song Liu <[email protected]>
Fixes: 6987561c9e ("perf annotate: Enable annotation of BPF programs")
Link: https://lkml.kernel.org/n/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
Add kernel header sanitizer check to drop struct epoll_event.
This struct epoll_event is not following the POSIX standard
and defining element in opaque data type.
Change-Id: I1eecef1b64eb1fb8f0dd6999263093a453e7b9fb
Signed-off-by: Prasad Sodagudi <[email protected]>
Signed-off-by: Elliot Berman <[email protected]>
The command DB may be initialized outside the AOP, indicated by the
reserved bit 0. Export this information through a function.
Change-Id: I7b8c685cc03d919c5adb1b91134078bd96599bbd
Signed-off-by: Lina Iyer <[email protected]>
Add support for compiling commandDB as module. Since the command DB data
is written to DDR by a remote processor and exists while the system is
active, removing the module does not make sense. Initialize the driver
as builtin platform driver.
Change-Id: I3e8909f556815b6831947661531f1e4d3c464a86
Signed-off-by: Lina Iyer <[email protected]>
Enable PDC irqchip for Qualcomm's Lahaina SoC. Increase the maximum
number of PDC pins to match the hardware.
Change-Id: I1c80d4c81c63a66c2a8dbf854e403b4b8c687060
Signed-off-by: Lina Iyer <[email protected]>
Modify spdx tag for power drivers for Lahaina. Update year in copyright
information.
Change-Id: Icac12f1ff1a46f6498212b1ed12c183d2af28ee8
Signed-off-by: Lina Iyer <[email protected]>
Pull cifs fixes from Steve French:
"Six small SMB3 fixes, two for stable"
* tag '5.3-rc3-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6:
SMB3: Kernel oops mounting a encryptData share with CONFIG_DEBUG_VIRTUAL
smb3: update TODO list of missing features
smb3: send CAP_DFS capability during session setup
SMB3: Fix potential memory leak when processing compound chain
SMB3: Fix deadlock in validate negotiate hits reconnect
cifs: fix rmmod regression in cifs.ko caused by force_sig changes
A deadlock with this stacktrace was observed.
The loop thread does a GFP_KERNEL allocation, it calls into dm-bufio
shrinker and the shrinker depends on I/O completion in the dm-bufio
subsystem.
In order to fix the deadlock (and other similar ones), we set the flag
PF_MEMALLOC_NOIO at loop thread entry.
PID: 474 TASK: ffff8813e11f4600 CPU: 10 COMMAND: "kswapd0"
#0 [ffff8813dedfb938] __schedule at ffffffff8173f405
#1 [ffff8813dedfb990] schedule at ffffffff8173fa27
#2 [ffff8813dedfb9b0] schedule_timeout at ffffffff81742fec
#3 [ffff8813dedfba60] io_schedule_timeout at ffffffff8173f186
#4 [ffff8813dedfbaa0] bit_wait_io at ffffffff8174034f
#5 [ffff8813dedfbac0] __wait_on_bit at ffffffff8173fec8
#6 [ffff8813dedfbb10] out_of_line_wait_on_bit at ffffffff8173ff81
#7 [ffff8813dedfbb90] __make_buffer_clean at ffffffffa038736f [dm_bufio]
#8 [ffff8813dedfbbb0] __try_evict_buffer at ffffffffa0387bb8 [dm_bufio]
#9 [ffff8813dedfbbd0] dm_bufio_shrink_scan at ffffffffa0387cc3 [dm_bufio]
#10 [ffff8813dedfbc40] shrink_slab at ffffffff811a87ce
#11 [ffff8813dedfbd30] shrink_zone at ffffffff811ad778
#12 [ffff8813dedfbdc0] kswapd at ffffffff811ae92f
#13 [ffff8813dedfbec0] kthread at ffffffff810a8428
#14 [ffff8813dedfbf50] ret_from_fork at ffffffff81745242
PID: 14127 TASK: ffff881455749c00 CPU: 11 COMMAND: "loop1"
#0 [ffff88272f5af228] __schedule at ffffffff8173f405
#1 [ffff88272f5af280] schedule at ffffffff8173fa27
#2 [ffff88272f5af2a0] schedule_preempt_disabled at ffffffff8173fd5e
#3 [ffff88272f5af2b0] __mutex_lock_slowpath at ffffffff81741fb5
#4 [ffff88272f5af330] mutex_lock at ffffffff81742133
#5 [ffff88272f5af350] dm_bufio_shrink_count at ffffffffa03865f9 [dm_bufio]
#6 [ffff88272f5af380] shrink_slab at ffffffff811a86bd
#7 [ffff88272f5af470] shrink_zone at ffffffff811ad778
#8 [ffff88272f5af500] do_try_to_free_pages at ffffffff811adb34
#9 [ffff88272f5af590] try_to_free_pages at ffffffff811adef8
#10 [ffff88272f5af610] __alloc_pages_nodemask at ffffffff811a09c3
#11 [ffff88272f5af710] alloc_pages_current at ffffffff811e8b71
#12 [ffff88272f5af760] new_slab at ffffffff811f4523
#13 [ffff88272f5af7b0] __slab_alloc at ffffffff8173a1b5
#14 [ffff88272f5af880] kmem_cache_alloc at ffffffff811f484b
#15 [ffff88272f5af8d0] do_blockdev_direct_IO at ffffffff812535b3
#16 [ffff88272f5afb00] __blockdev_direct_IO at ffffffff81255dc3
#17 [ffff88272f5afb30] xfs_vm_direct_IO at ffffffffa01fe3fc [xfs]
#18 [ffff88272f5afb90] generic_file_read_iter at ffffffff81198994
#19 [ffff88272f5afc50] __dta_xfs_file_read_iter_2398 at ffffffffa020c970 [xfs]
#20 [ffff88272f5afcc0] lo_rw_aio at ffffffffa0377042 [loop]
#21 [ffff88272f5afd70] loop_queue_work at ffffffffa0377c3b [loop]
#22 [ffff88272f5afe60] kthread_worker_fn at ffffffff810a8a0c
#23 [ffff88272f5afec0] kthread at ffffffff810a8428
#24 [ffff88272f5aff50] ret_from_fork at ffffffff81745242
Signed-off-by: Mikulas Patocka <[email protected]>
Cc: [email protected]
Signed-off-by: Jens Axboe <[email protected]>
Currently, the authorized_default and interface_authorized_default
attributes for HCD are set up after the uevent has been sent to userland.
This creates a race condition where userland may fail to access this
file when processing the event. Move the appending of these attributes
earlier relying on the usb_bus_notify dispatcher.
Signed-off-by: Thiébaud Weksteen <[email protected]>
Cc: stable <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
Commit 89e524c04f ("loop: Fix mount(2) failure due to race with
LOOP_SET_FD") converted blkdev_get() to use the new helpers for
finishing claiming of a block device. However the conversion botched the
error handling in blkdev_get() and thus the bdev has been marked as held
even in case __blkdev_get() returned error. This led to occasional
warnings with block/001 test from blktests like:
kernel: WARNING: CPU: 5 PID: 907 at fs/block_dev.c:1899 __blkdev_put+0x396/0x3a0
Correct the error handling.
CC: [email protected]
Fixes: 89e524c04f ("loop: Fix mount(2) failure due to race with LOOP_SET_FD")
Signed-off-by: Jan Kara <[email protected]>
Signed-off-by: Jens Axboe <[email protected]>
Since commit 13a857a4c4 ("block, bfq: detect wakers and
unconditionally inject their I/O"), every bfq_queue has a pointer to a
waker bfq_queue and a list of the bfq_queues it may wake. In this
respect, when a bfq_queue, say Q, remains with no I/O source attached
to it, Q cannot be woken by any other bfq_queue, and cannot wake any
other bfq_queue. Then Q must be removed from the woken list of its
possible waker bfq_queue, and all bfq_queues in the woken list of Q
must stop having a waker bfq_queue.
Q remains with no I/O source in two cases: when the last process
associated with Q exits or when such a process gets associated with a
different bfq_queue. Unfortunately, commit 13a857a4c4 ("block, bfq:
detect wakers and unconditionally inject their I/O") performed the
above updates only in the first case.
This commit fixes this bug by moving these updates to when Q gets
freed. This is a simple and safe way to handle all cases, as both the
above events, process exit and re-association, lead to Q being freed
soon, and because dangling references would come out only after Q gets
freed (if no update were performed).
Fixes: 13a857a4c4 ("block, bfq: detect wakers and unconditionally inject their I/O")
Reported-by: Douglas Anderson <[email protected]>
Tested-by: Douglas Anderson <[email protected]>
Signed-off-by: Paolo Valente <[email protected]>
Signed-off-by: Jens Axboe <[email protected]>
Since commit 13a857a4c4 ("block, bfq: detect wakers and
unconditionally inject their I/O"), BFQ stores, in a per-device
pointer last_completed_rq_bfqq, the last bfq_queue that had an I/O
request completed. If some bfq_queue receives new I/O right after the
last request of last_completed_rq_bfqq has been completed, then
last_completed_rq_bfqq may be a waker bfq_queue.
But if the bfq_queue last_completed_rq_bfqq points to is freed, then
last_completed_rq_bfqq becomes a dangling reference. This commit
resets last_completed_rq_bfqq if the pointed bfq_queue is freed.
Fixes: 13a857a4c4 ("block, bfq: detect wakers and unconditionally inject their I/O")
Reported-by: Douglas Anderson <[email protected]>
Tested-by: Douglas Anderson <[email protected]>
Signed-off-by: Paolo Valente <[email protected]>
Signed-off-by: Jens Axboe <[email protected]>
Currently empty .bss checks performed do not pay attention to "common
objects" in object files which end up in .bss section eventually.
The "size" tool is a part of binutils and since version 2.18 provides
"--common" command line option, which allows to account "common objects"
sizes in .bss section size. Utilize "size --common" to perform accurate
check that .bss section is unused. Besides that the size tool handles
object files without .bss section gracefully and doesn't require
additional objdump run.
The linux kernel requires binutils 2.20 since 4.13.
Kbuild exports OBJSIZE to reference the right size tool.
Link: http://lkml.kernel.org/r/patch-2.thread-2257a1.git-2257a1c53d4a.your-ad-here.call-01565088755-ext-5120@work.hours
Reported-and-tested-by: Heiko Carstens <[email protected]>
Acked-by: Heiko Carstens <[email protected]>
Signed-off-by: Vasily Gorbik <[email protected]>
Define and export OBJSIZE variable for "size" tool from binutils to be
used in architecture specific Makefiles (naming the variable just "SIZE"
would be too risky). In particular this tool is useful to perform checks
that early boot code is not using bss section (which might have not been
zeroed yet or intersects with initrd or other files boot loader might
have put right after the linux kernel).
Link: http://lkml.kernel.org/r/patch-1.thread-2257a1.git-188f5a3d81d5.your-ad-here.call-01565088755-ext-5120@work.hours
Acked-by: Masahiro Yamada <[email protected]>
Signed-off-by: Vasily Gorbik <[email protected]>
Commit 4a6ef8e37c ("pwm: Add support referencing PWMs from ACPI")
made pwm_get unconditionally return the acpi_pwm_get return value if
the device passed to pwm_get has an ACPI fwnode.
But even if the passed in device has an ACPI fwnode, it does not
necessarily have the necessary ACPI package defining its pwm bindings,
especially since the binding / API of this ACPI package has only been
introduced very recently.
Up until now X86/ACPI devices which use a separate pwm controller for
controlling their LCD screen's backlight brightness have been relying
on the static lookup-list to get their pwm.
pwm_get unconditionally returning the acpi_pwm_get return value breaks
this, breaking backlight control on these devices.
This commit fixes this by making pwm_get fall back to the static
lookup-list if acpi_pwm_get returns -ENOENT.
BugLink: https://bugs.freedesktop.org/show_bug.cgi?id=96571
Reported-by: [email protected]
Fixes: 4a6ef8e37c ("pwm: Add support referencing PWMs from ACPI")
Cc: Nikolaus Voss <[email protected]>
Signed-off-by: Hans de Goede <[email protected]>
Reviewed-by: Andy Shevchenko <[email protected]>
Acked-by: Nikolaus Voss <[email protected]>
Signed-off-by: Thierry Reding <[email protected]>
Currently when too many retries have occurred there is a memory
leak on the allocation for reply on the error return path. Fix
this by kfree'ing reply before returning.
Addresses-Coverity: ("Resource leak")
Fixes: a9cd9c044a ("drm/vmwgfx: Add a check to handle host message failure")
Signed-off-by: Colin Ian King <[email protected]>
Reviewed-by: Deepak Rawat <[email protected]>
Signed-off-by: Deepak Rawat <[email protected]>
Signed-off-by: Thomas Hellstrom <[email protected]>
