A memory clock value (MCLK) is changed to a minimum required by a current
mode bandwidth. This usually lowers the MCLK to its minimum (50 MHz) thus
decreasing the card performance. Just leave the MCLK value set by card
BIOS.
The CL-GD5446 Technical Reference Manual point 9.9.1.3 states that if a
pixclock value is close (~1%) to the MCLK or MCLK/2 this may result in a
jitter on the screen. A countermeasure is to use the MCLK as pixclock
source instead of a VCLK. The patch implements this as well.
Signed-off-by: Krzysztof Helt <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
The 16bpp mode did not work on the Cirrus cards as the visual type was set
to DIRECTCOLOR instead of TRUECOLOR. The Alpine family used one incorrect
register setting so this 16bpp modes generated wrong horizontal frequency.
Signed-off-by: Krzysztof Helt <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
The noaccel parameter is already handled if the driver is not built as
module.
Signed-off-by: Krzysztof Helt <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
Move call to pixclock calculation into the cirrusfb_set_par_foo(). It
makes copy of clock registers redundant.
Simplify clock calculations further.
Signed-off-by: Krzysztof Helt <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
Move calculations of CRT register values into the cirrusfb_set_par_foo()
where the values are used.
Signed-off-by: Krzysztof Helt <[email protected]>
Cc: Geert Uytterhoeven <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
Add __devinit attribute to probing functions. This fixed section mismatch
warning from my previous patch.
Kill one redundant forward declaration.
Signed-off-by: Krzysztof Helt <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
Use modedb for initial mode instead of table of few predefined modes.
Add mode_option module parameter as a step toward unification of frame
buffers' parameters.
Signed-off-by: Krzysztof Helt <[email protected]>
Cc: Geert Uytterhoeven <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
The device pointer can be easily obtained from fb_info->device if needed.
Signed-off-by: Krzysztof Helt <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
The 24 bpp mode is not implemented. Disallow it in the
cirrusfb_check_var() and remove it from checks.
Signed-off-by: Krzysztof Helt <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
Remove information about memory size displayed twice each time a display
mode change.
Signed-off-by: Krzysztof Helt <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
Add support for Intel's 945GME graphics chip to the intelfb driver. I
have assumed that the 945GME is identical to the already-supported 945GM
apart from its PCI IDs; this is based on a quick look at the X driver for
these chips which seems to treat them identically.
The 945GME is used in the ASUS Eee 901, and I coded this in the hope that
I'd be able to use it to get a console at the native 1024x600 resolution
which is not known to the BIOS. I realised too late that the intelfb
driver does not support mode changing on laptops, so it won't be any
use for me.
Signed-off-by: Phil Endecott <[email protected]>
Acked-by: Krzysztof Helt <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
This was suggested by Geert Uytterhoeven to avoid overwriting of default
values from the tdfx_fix.
Signed-off-by: Krzysztof Helt <[email protected]>
Cc: Geert Uytterhoeven <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
Remove mutex from the fb_open/fb_release functions as these operations are
mutexed at fb layer.
Signed-off-by: Krzysztof Helt <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
Remove mutex from the fb_open/fb_release functions as these operations are
mutexed at fb layer.
Signed-off-by: Krzysztof Helt <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
Move common code outside if/else or switch/case clauses.
Drop checks done twice inside the neofb_check_var().
Signed-off-by: Krzysztof Helt <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
via_utility.c, via_utility.h: support user mode application with
additional information vt1636.c, vt1636.h: setting for chip vt1636
Signed-off-by: Joseph Chan <[email protected]>
Cc: Krzysztof Helt <[email protected]>
Cc: Geert Uytterhoeven <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
Remove the macro MMIO_OUT32, and replace it with writel() function.
And replace "u32" with "unsigned long" in writel() function (original
MMIO_OUT32 marco) for avoiding warning message in 64bit OS.
Signed-off-by: Joseph Chan <[email protected]>
Acked-by: Krzysztof Helt <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
iface.c, iface.h: support getting video memory from backdoor.
ioctl.c, ioctl.h: support user mode application with additional information
Signed-off-by: Joseph Chan <[email protected]>
Cc: Krzysztof Helt <[email protected]>
Cc: Geert Uytterhoeven <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
Correct via_fb_ to viafb_ and remove the Kconfig part in viafb.txt.
viafb.modes: supported mode table
viafb.txt: documentation of viafb driver
Signed-off-by: Joseph Chan <[email protected]>
Cc: Krzysztof Helt <[email protected]>
Cc: Geert Uytterhoeven <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
Reduce panning function by deleting checks done by higher layer and
folding remaining function into the called one.
Signed-off-by: Krzysztof Helt <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
The bug was in fb_ddc and was fixed by commit
b64d70825a (fb_ddc: fix DDC lines quirk) so
the workaround in radeonfb can be removed now.
Signed-off-by: Jean Delvare <[email protected]>
Cc: Benjamin Herrenschmidt <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
Add a new internal mechanism to gpiolib to support low power
operations by letting gpio_chip instances see when their GPIOs
are in use. When no GPIOs are active, chips may be able to
enter lower powered runtime states by disabling clocks and/or
power domains.
Signed-off-by: David Brownell <[email protected]>
Cc: "Magnus Damm" <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
This updates most of the OMAP drivers which are in mainline to switch to
using the cross-platform GPIO calls instead of the older OMAP-specific
ones.
This is all fairly brainless/obvious stuff. Probably the most interesting
bit is to observe that the omap-keypad code seems to now have a portable
core that could work with non-OMAP matrix keypads. (That would improve
with hardware IRQ debouncing enabled, of course...)
Signed-off-by: David Brownell <[email protected]>
Signed-off-by: Tony Lindgren <[email protected]>
Cc: Dmitry Torokhov <[email protected]>
Cc: Antonino Daplas <[email protected]>
Cc: David Woodhouse <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
Add a new gpiolib mechanism: gpio_chip instances can provide mappings
between their (input) GPIOs and any associated IRQs. This makes it easier
for platforms to support IRQs that are provided by board-specific external
chips instead of as part of their core (such as SOC-integrated GPIOs).
Also update the irq_to_gpio() description, saying to avoid it because it's
not always supported.
Signed-off-by: David Brownell <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
Make the I2C external GPIO expander drivers register themselves at
subsys_initcall() time when they're statically linked.
SOC-integrated GPIOs are available starting very early -- early in
arch_initcall() at latest, but often even before initcalls start to run --
so this improves consistency, so more subsystems can rely on GPIOs in
their own subsys_initcall() code.
(This isn't a theoretical problem. This is one of several patches needed
to resolve oopsing observed when statically linking kernels on a DaVinci
EVM. Its pcf857x GPIOs needed to be available well before some other
drivers initialized.)
Signed-off-by: David Brownell <[email protected]>
Cc: Jean Delvare <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
According to the documentation gpio_free should only be called from task
context only. To make this more explicit add a might sleep to all
implementations.
This is the generic part which changes gpiolib and the fallback
implementation only.
Signed-off-by: Uwe Kleine-König <[email protected]>
Cc: David Brownell <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
There is a small race and code ugliness in max7301: pins are reconfigured
after the chip is registered. Swap these calls so that the device is
registered in correct state.
Also this fixes the comile-time warning about unchecked gpiochip_remove.
Signed-off-by: Dmitry Baryshkov <[email protected]>
Cc: Juergen Beisert <[email protected]>
Cc: Guennadi Liakhovetski <[email protected]>
Cc: Russell King <[email protected]>
Cc: David Brownell <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
Mark gpiochip label as a const char pointer. Fixes things like
arch/arm/common/scoop.c: In function `scoop_probe':
arch/arm/common/scoop.c:250: warning: assignment discards qualifiers from pointer target type
Signed-off-by: Dmitry Baryshkov <[email protected]>
Acked-by: David Brownell <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
The non-functional periodic IRQ support was previously removed from the
AT91RM9200 RTC driver. Remove the remaining AT91_RTC_FREQ definition.
Signed-off-by: Andrew Victor <[email protected]>
Cc: David Brownell: <[email protected]>
Cc: Alessandro Zummo: <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
Add support for M41T65 Real Time Clock chip.
The main differences I see between the M41T65 and M41T80 are that:
1) The M41T65 watchdog timer has three bits controlling resolution
(versus two for the M41T80).
2) There is no register 0x13 for controlling square-wave output.
Signed-off-by: Steven A. Falco <[email protected]>
Acked-by: Alessandro Zummo <[email protected]>
Cc: "Maciej W. Rozycki" <[email protected]>
Acked-by: Atsushi Nemoto <[email protected]>
Cc: David Brownell <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
Make the rtc framework consistent about disabling 1/second update IRQs
that may have been activated through the /dev interface, when that /dev
file is closed. (It may have closed because of coredump, etc.) This was
previously done only for emulated update IRQs ... now, do it always.
Also comment the current policy: repeating IRQs (periodic, update) that
userspace enabled will be cleanly disabled, but alarms are left alone.
Such repeating IRQs are a constant and pointless system load.
Update some RTC drivers to remove now-needless release() methods. Most
such methods just enforce that policy. The others all seem to be buggy,
and mistreat in-kernel clients of periodic or alarm IRQs.
Signed-off-by: David Brownell <[email protected]>
Acked-by: Andrew Sharp <[email protected]>
Cc: Angelo Castello <[email protected]>
Acked-by: Atsushi Nemoto <[email protected]>
Acked-by: Paul Mundt <[email protected]>
Cc: Thomas Hommel <[email protected]>
Acked-by: Alessandro Zummo <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
rtc-rs5c372 presently depends on I2C master mode transfers, despite the
fact that these RTCs frequently find themselves on SMBus-only adapters.
Given that the only capabilities that were checked were for I2C_FUNC_I2C,
it's assumed that most of the adapters that are currently using this
driver are fairly sane, and are able to handle SMBus emulation (though we
adjust the default capabilities to check for I2C_FUNC_SMBUS_EMUL anyways,
which is the vast majority of them. The adapters that don't have their
own ->smbus_xfer() fall back on the ->master_xfer() through the emulated
transfer).
The special case is iop3xx, which has more than its fair share of hacks
within this driver, it remains untested -- though also claims to support
emulated SMBus accesses. The corner case there is rs5c_get_regs() which
uses access mode #3 for transferring the register state, while we use mode
#1 for SMBus.
Signed-off-by: Paul Mundt <[email protected]>
Acked-by: David Brownell <[email protected]>
Tested-by: Riku Voipio <[email protected]>
Acked-by: Alessandro Zummo <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
HPET_RTC_IRQ is no longer needed; HPET_EMULATE_RTC suffices and is more
correct. (http://bugzilla.kernel.org/show_bug.cgi?id=11111)
Note that when using the legacy RTC driver, platforms don't really do a
dynamic switch between HPET and non-HPET modes based on whether HPET
hardware actually exists ... only rtc-cmos (using the new RTC framework)
currently switches that way.
So this reflects bitrot in that legacy code, for x86/ia64: kernels with
HPET support configured (e.g. for a clocksource) can't get IRQs from the
legacy RTC driver unless they really have HPET hardware. (The obvious
workaround is to not use the legacy RTC driver on those platforms when you
configure HPET ... unless you know the target really has a HPET.)
Signed-off-by: David Brownell <[email protected]>
Cc: Alessandro Zummo <[email protected]>
Cc: Ingo Molnar <[email protected]>
Cc: Thomas Gleixner <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
