packed should always exist without calling its cleanup function
explicitly. Moreover, we have use it when preparing packed list.
So I don't believe we should ever fall into this check again when
doing mmc_blk_packed_hdr_wrq_prep or mmc_blk_end_packed_req,etc.
And the code of mmc_blk_end_packed_req is trying to use packed before
checking it which makes it quite weird. This patch is trying to
remove these two checks and move it to the mmc_blk_prep_packed_list.
If we find packed is null, then we should never use MMC_BLK_PACKED_CMD.
By doing this, we could fall back to non-packed request if finding null
packed, though it's impossible theoretically.
After removing these two BUG_ONs, we also remove all other similar
checks within the routine of mmc_blk_issue_rw_rq which checks the
error handling of packed request.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The switch failure message in mmc_select_timing() had been removed
since that is invalid: commit 0400ed0a08 ("mmc: core: remove the
invalid message in mmc_select_timing")
Now, in the case when mmc_select_hs() return error in mmc_select_timing(),
there is nothing to print failure message.
Let's make for mmc_select_hs() print message itself in the failure case.
Signed-off-by: Jungseung Lee <js07.lee@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Populating card_busy caused a side-effect on a chip variant we don't
have documentation for (r8a73a4). So, enable it and voltage switching
only on devices known to support those features.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fixes: 452e5eef6d ("mmc: tmio: Add UHS-I mode support")
card_busy is only used/tested on SDHI for R-Car Gen2 and later.
Move it to the SDHI driver, so we can then activate it conditionally
depending on the SDHI type.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The sunxi-mmc driver does not take into account the processor may be big
endian when writing the DMA descriptors. This causes cards not to be
detected when running a big-endian kernel. Change the descriptors for
IDMA to use __le32 and ensure they are suitably swapped before writing.
Tested successfully on the Cubieboard2.
Signed-off-by: Michael Weiser <michael.weiser@gmx.de>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: linux-mmc@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
clk_round_rate() may return an error. Check it.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
PHY intended to be used with the Arasan SDHCI 5.1 controller has trouble
turning on when the card clock is slow or off. Strangely these problems
appear to show up consistently on some boards while other boards work
fine, but on the boards where it shows up the problem reproduces 100% of
the time and is quite consistent in its behavior.
These problems can be fixed by always making sure that we power on the
PHY (and turn on its DLL) when the card clock is faster than about 50
MHz. Once on, we need to make sure that we never power down the PHY /
turn off its DLL until the clock is faster again.
We'll add logic for handling this into the sdhci-of-arasan driver. Note
that right now the only user of a PHY in the sdhci-of-arasan driver is
arasan,sdhci-5.1. It's presumed that all arasan,sdhci-5.1 PHY
implementations need this workaround, so the logic is only contingent on
having a PHY to control. If future Arasan controllers don't have this
problem we can add code to decide if we want this flow or not.
Also note that we check for slow clocks by checking for <= 400 kHz
rather than checking for 50 MHz. This keeps things the most consistent
and also means we can power the PHY on at max speed (where the DLL will
lock fastest). Presumably anyone who intends to run with a card clock
of < 50 MHz and > 400 kHz will be running on a device where this problem
is fixed anyway.
I believe this brings some resolution to the problems reported before.
See the commit 6fc09244d7 ("mmc: sdhci-of-arasan: Revert: Always power
the PHY off/on when clock changes").
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
wait_event_interruptible_timeout() will return early if the blocked
process receives a signal, causing the driver to abort the tuning
procedure and possibly leaving the controller in a bad state. Since the
tuning command is expected to complete quickly (<50ms) and we've set a
timeout, use wait_event_timeout() instead.
Signed-off-by: Christopher Freeman <cfreeman@nvidia.com>
Tested-by: Robert Foss <robert.foss@collabora.com>
Signed-off-by: Robert Foss <robert.foss@collabora.com>
Reviewed-by: Benson Leung <bleung@chromium.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
i.MX USDHC Reference Manual has a mistake, for the register SYS_CTRL,
the DTOCV(bit 19~16) means the data timeout counter value. When DTOCV
is set to 0xF, it means SDCLK << 29, not SDCLK << 28.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Now, when call esdhc_set_timeout() to set the data timeout counter value,
IPP_RST_N(bit 23) is wrongly affected. This patch add a mask to avoid this.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The field "owner" is set by core. Thus delete an extra initialisation.
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The SD Status register contains several important fields related to the
SD Card proprietary features.
Those fields may be used by user space applications for vendor specific
usage.
None of those fields are exported today by the driver to user space.
In this patch, we are reading the SD Status register and exporting
(using MMC_DEV_ATTR) the SD Status register to the user space.
Signed-off-by: Uri Yanai <uri.yanai@sandisk.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use of_property_read_bool to check for the existence of a property.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e1,e2;
statement S2,S1;
@@
- if (of_get_property(e1,e2,NULL))
+ if (of_property_read_bool(e1,e2))
S1 else S2
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The core MMC code adds two (optional) regulator properites that drivers
should use to get their supplies. This is not documented anywhere so add
information on it.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In clk_set_rate() or clk_prepare_enable() error handling case, the
error return code ret is not set, so sdhci_bcm_kona_probe() return
0 in those error cases.
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Acked-by: Ray Jui <ray.jui@broadcom.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
wait_for_completion_timeout_interruptible returns long not unsigned long
so dma_time, which is used exclusively here, is changed to long.
Fixes: 1b66e94e6b ("mmc: moxart: Add MOXA ART SD/MMC driver")
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some devices need a while to boot their firmware after providing clks /
de-asserting resets before they are ready to receive sdio commands.
This commits adds a post-power-on-delay-ms devicetree property to
mmc-pwrseq-simple for use with such devices.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
On some boards (android tablets) different batches use different sdio
wifi modules. This is not a problem since mmc/sdio is an enumerable bus,
so we only need to describe and activate the mmc controller in dt and
then the kernel will automatically load the right driver.
Sometimes it is useful to specify certain ethernet properties for these
"unknown" sdio devices, specifically we want the boot-loader to be able
to set "local-mac-address" as some of these sdio wifi modules come without
an eeprom / without a factory programmed mac address.
Since the exact device is unknown (differs per batch) we cannot use
a wifi-chip specific compatible, thus sometimes it is desirable to have a
mmc function node, without having to make up an otherwise unused compatible
for the node, so make the compatible property optional.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use the new sun7i-a20-mmc compatible for the mmc controllers on sun7i
and newer.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It turns out that sun4i (A10) and sun5i (A13 & co) do not have sample
clocks, so add a new sun7i-a20-mmc compatible and do not try to use
sample clocks on sun4i / sun5i.
Since sun4i / sun5i do not have sample clocks, they cannot (reliably) do
DDR rates, so only set MMC_CAP_1_8V_DDR when we do have sample clks.
Note this patch leaves the clk_prepare_enable() / clk_disable_unprepare()
calls to the sample clks as-is, without adding checks for them being
NULL. All the clk_foo calls accept a NULL clk and will return success when
called with a NULL clk.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add a sunxi_mmc_clk_set_phase() helper function.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Create a struct to hold the various model / compatible string dependend
settings.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When support for the sample clks was added calls to prepare_enable
were added to the probe path, but matching calls to disable_unprepare
were forgotten in the remove path, this fixes this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
A setclientid_confirm with (clientid, verifier) both matching an
existing confirmed record is assumed to be a replay, but if the verifier
doesn't match, it shouldn't be.
This would be a very rare case, except that clients following
https://tools.ietf.org/html/rfc7931#section-5.8 may depend on the
failure.
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
NFSv4.1 has built-in trunking support that allows a client to determine
whether two connections to two different IP addresses are actually to
the same server. NFSv4.0 does not, but RFC 7931 attempts to provide
clients a means to do this, basically by performing a SETCLIENTID to one
address and confirming it with a SETCLIENTID_CONFIRM to the other.
Linux clients since 05f4c350ee "NFS: Discover NFSv4 server trunking
when mounting" implement a variation on this suggestion. It is possible
that other clients do too.
This depends on the clientid and verifier not being accepted by an
unrelated server. Since both are 64-bit values, that would be very
unlikely if they were random numbers. But they aren't:
knfsd generates the 64-bit clientid by concatenating the 32-bit boot
time (in seconds) and a counter. This makes collisions between
clientids generated by the same server extremely unlikely. But
collisions are very likely between clientids generated by servers that
boot at the same time, and it's quite common for multiple servers to
boot at the same time. The verifier is a concatenation of the
SETCLIENTID time (in seconds) and a counter, so again collisions between
different servers are likely if multiple SETCLIENTIDs are done at the
same time, which is a common case.
Therefore recent NFSv4.0 clients may decide two different servers are
really the same, and mount a filesystem from the wrong server.
Fortunately the Linux client, since 55b9df93dd "nfsv4/v4.1: Verify the
client owner id during trunking detection", only does this when given
the non-default "migration" mount option.
The fault is really with RFC 7931, and needs a client fix, but in the
meantime we can mitigate the chance of these collisions by randomizing
the starting value of the counters used to generate clientids and
verifiers.
Reported-by: Frank Sorenson <fsorenso@redhat.com>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
If we are using v4.1+, then we can send notification when contended
locks become free. Inform the client of that fact.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
It's possible for a client to call in on a lock that is blocked for a
long time, but discontinue polling for it. A malicious client could
even set a lock on a file, and then spam the server with failing lock
requests from different lockowners that pile up in a DoS attack.
Add the blocked lock structures to a per-net namespace LRU when hashing
them, and timestamp them. If the lock request is not revisited after a
lease period, we'll drop it under the assumption that the client is no
longer interested.
This also gives us a mechanism to clean up these objects at server
shutdown time as well.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Create a new per-lockowner+per-inode structure that contains a
file_lock. Have nfsd4_lock add this structure to the lockowner's list
prior to setting the lock. Then call the vfs and request a blocking lock
(by setting FL_SLEEP). If we get anything besides FILE_LOCK_DEFERRED
back, then we dequeue the block structure and free it. When the next
lock request comes in, we'll look for an existing block for the same
filehandle and dequeue and reuse it if there is one.
When the lock comes free (a'la an lm_notify call), we dequeue it
from the lockowner's list and kick off a CB_NOTIFY_LOCK callback to
inform the client that it should retry the lock request.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Add the encoding/decoding for CB_NOTIFY_LOCK operations.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Add an entry for the GPIO mockup driver with myself as maintainer.
Signed-off-by: Bamvor Jian Zhang <bamvor.zhangjian@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch add basic structure of a virtual gpio device(gpio-mockup)
for testing gpio subsystem. The tester could manipulate such device
through userspace(sysfs or char device) and check the result from
debugfs.
Currently, it support one or more gpiochip(determined by module
parameters with base,ngpio pair). One could test the overlap of
different gpiochip and test the direction and/or output values of
these chips.
Signed-off-by: Kamlakant Patel <kamlakant.patel@broadcom.com>
Signed-off-by: Bamvor Jian Zhang <bamvor.zhangjian@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix for commit 719ee344: initialize atime of I_NEW inodes to 0 so that
the timestamps read from disk will always be more recent than the
initial timestamp, and the atime in the I_NEW inode will be set correctly.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
In gfs2_page_mkwrite, grab the inode glock in EX mode before calling
file_update_time: grabbing the lock may result in a call to
gfs2_dinode_in, which will reset the file times to their on-disk state.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
By design notifier can be registered once only, however nfsd registers
the same inetaddr notifiers per net-namespace. When this happen it
corrupts list of notifiers, as result some notifiers can be not called
on proper event, traverse on list can be cycled forever, and second
unregister can access already freed memory.
Cc: stable@vger.kernel.org
fixes: 36684996 ("nfsd: Register callbacks on the inetaddr_chain and inet6addr_chain")
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
They seem to be there from the first day. We calculate these values but
never use them.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When we're not able to get enough space through splitting leaf,
we'd create a new sibling leaf instead, and it's possible that we return
a zero-nritem sibling leaf and mark it dirty before it's in a consistent
state. With CONFIG_BTRFS_FS_CHECK_INTEGRITY=y, the integrity check of
check_leaf will report panic due to this zero-nritem non-root leaf.
This removes the unnecessary btrfs_mark_buffer_dirty.
Reported-by: Filipe Manana <fdmanana@gmail.com>
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
This function is called from get_station callback which means that every
time user space was getting/dumping station(s) we were leaking 2 KiB.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Fixes: 1f0dc59a6d ("brcmfmac: rework .get_station() callback")
Cc: stable@vger.kernel.org # 4.2+
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The A83T SoC has the same dma engine as the A31 (sun6i), with a reduced
amount of endpoints and physical channels.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch updates the s3c24xx dma driver to be able to pass a
dma_slave_map array via the platform data. This is needed to
be able to use the new, simpler dmaengine API [1].
I used the virtual DMA channels as a parameter for the dma_filter
function. By doing that, I could reuse the existing filter function in
drivers/dma/s3c24xx-dma.c.
I have tested this on my mini2440 board with the audio driver.
According to my observations, dma_request_slave_channel in the
function dmaengine_pcm_new in the file
sound/soc/soc-generic-dmaengine-pcm.c now returns a valid DMA channel
whereas before no DMA channel was returned at that point.
Entries for DMACH_XD0, DMACH_XD1 and DMACH_TIMER are missing because I
don't realy know which driver to use for these.
[1]
http://lists.infradead.org/pipermail/linux-arm-kernel/2015-December/393635.html
Signed-off-by: Sam Van Den Berge <sam.van.den.berge@telenet.be>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
As soon as debugging is turned on, the logs are filled with messages
reporting the interrupt status. As this quantity is usually zero, this
output is not needed. In fact, there will be a report if the status is
not zero, thus the debug line in question could probably be deleted.
Rather than taking that action, I have changed it to only be printed
when the newly added RTL8XXXU_DEBUG_INTERRUPT bit is set in the debug
mask.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This saves some 217, or about, derefences of priv->fops.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Remove last_tx_page argument from the llt_init() function. The
rtl8xxxu_fileops structure contains the correct TX_TOTAL_PAGE_NUM
value for the device, and rtl8xxxu_auto_llt_table() doesn't need to
know the value in the first place.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This was detected tracing the 8188eu driver, but doesn't seem to make
any difference when using it.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch helps get rid of goto statement and improves readability.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It's been observed that in a corner case mwifiex_usb_tx_complete()
gets called before we exit from mwifiex_usb_host_to_card() after
submitting the urb. 'data_sent' flag remains set in this case. It
blocks further Tx packets and triggers watchdog timeout.
The problem is fixed by setting data_sent and port_block flag at
correct place.
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Shengzhen Li <szli@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Following crash issue is observed during TCP traffic stress
test
[ 2253.625439] NMI watchdog: BUG: soft lockup - CPU#3 stuck for 22s!
[kworker/u17:1:5191]
[ 2253.625520] Call Trace:
[ 2253.625527] [<ffffffffc0b47030>] ? moal_spin_lock+0x30/0x30
[usb8xxx]
[ 2253.625533] [<ffffffffc0ac3ceb>] ? wlan_wmm_lists_empty+0xb/0xf0
[mlan]
[ 2253.625537] [<ffffffffc0ab0ea3>] mlan_main_process+0x1b3/0x720
[mlan]
[ 2253.625540] [<ffffffffc0b337f5>] woal_main_work_queue+0x45/0x80
[usb8xxx]
[ 2253.625543] [<ffffffff8108aaf0>] process_one_work+0x150/0x3f0
[ 2253.625545] [<ffffffff8108b1e1>] worker_thread+0x121/0x520
[ 2253.625547] [<ffffffff8108b0c0>] ? rescuer_thread+0x330/0x330
[ 2253.625549] [<ffffffff81090222>] kthread+0xd2/0xf0
[ 2253.625551] [<ffffffff81090150>] ?
kthread_create_on_node+0x1c0/0x1c0
[ 2253.625553] [<ffffffff8179423c>] ret_from_fork+0x7c/0xb0
[ 2253.625555] [<ffffffff81090150>] ?
kthread_create_on_node+0x1c0/0x1c0
In mwifiex_usb_tx_complete(), we are updating port->block_status first
and then freeing the skb attached to that URB. We may end up attaching
new skb to URB in a corner case and same will be freed. This results in
the kernel crash. The problem is solved by changing the sequence.
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Shengzhen Li <szli@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Adjust a jump label according to the current Linux coding style convention.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Adjust a jump label according to the current Linux coding style convention.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
