We already have the DEFINE_SHOW_ATTRIBUTE, There is no need to define
such a macro, so remove define_genpd_open_function and
define_genpd_debugfs_fops.
Convert them to DEFINE_SHOW_ATTRIBUTE.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
PM-runtime uses the timer infrastructure for autosuspend. This implies
that the minimum time before autosuspending a device is in the range
of 1 tick included to 2 ticks excluded
-On arm64 this means between 4ms and 8ms with default jiffies
configuration
-And on arm, it is between 10ms and 20ms
These values are quite high for embedded systems which sometimes want
the duration to be in the range of 1 ms.
It is possible to switch autosuspend over to using hrtimers to get
finer granularity for short durations and take advantage of slack to
retain some margins and get long timeouts with minimum wakeups.
On an arm64 platform that uses 1ms for autosuspending timeout of its
GPU, idle power is reduced by 10% with hrtimer.
The latency impact on arm64 hikey octo cores is:
- mark_last_busy: from 1.11 us to 1.25 us
- rpm_suspend: from 15.54 us to 15.38 us
[Only the code path of rpm_suspend() that starts hrtimer has been
measured.]
arm64 image (arm64 default defconfig) decreases by around 3KB
with following details:
$ size vmlinux-timer
text data bss dec hex filename
12034646 6869268 386840 19290754 1265a82 vmlinux
$ size vmlinux-hrtimer
text data bss dec hex filename
12030550 6870164 387032 19287746 1264ec2 vmlinux
The latency impact on arm 32bits snowball dual cores is :
- mark_last_busy: from 0.31 us usec to 0.77 us
- rpm_suspend: from 6.83 us to 6.67 usec
The increase of the image for snowball platform that I used for
testing performance impact, is neglictable (244B).
$ size vmlinux-timer
text data bss dec hex filename
7157961 2119580 264120 9541661 91981d build-ux500/vmlinux
size vmlinux-hrtimer
text data bss dec hex filename
7157773 2119884 264248 9541905 919911 vmlinux-hrtimer
And arm 32bits image (multi_v7_defconfig) increases by around 1.7KB
with following details:
$ size vmlinux-timer
text data bss dec hex filename
13304443 6803420 402768 20510631 138f7a7 vmlinux
$ size vmlinux-hrtimer
text data bss dec hex filename
13304299 6805276 402768 20512343 138fe57 vmlinux
Signed-off-by: Vincent Guittot <vincent.guittot@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The radiotap vendor data might be placed after some other
radiotap elements, and thus when accessing it, need to access
the correct offset in the skb data. Fix the code accordingly.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fix two bugs in ieee80211_get_vht_max_nss():
* the spec says we should round down
(reported by Nissim)
* there's a double condition, the first one is wrong,
supp_width == 0 / ext_nss_bw == 2 is valid in 80+80
(found by smatch)
Fixes: b0aa75f0b1 ("ieee80211: add new VHT capability fields/parsing")
Reported-by: Nissim Bendanan <nissimx.bendanan@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
mac80211 uses the frag list to build AMSDU. When freeing
the skb, it may not be really freed, since someone is still
holding a reference to it.
In that case, when TCP skb is being retransmitted, the
pointer to the frag list is being reused, while the data
in there is no longer valid.
Since we will never get frag list from the network stack,
as mac80211 doesn't advertise the capability, we can safely
free and nullify it before releasing the SKB.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If validate_pae_over_nl80211() were to fail in nl80211_crypto_settings(),
we might leak the 'connkeys' allocation. Fix this.
Fixes: 64bf3d4bc2 ("nl80211: Add CONTROL_PORT_OVER_NL80211 attribute")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Due to the alignment handling, it actually matters where in the code
we add the 4 bytes for the presence bitmap to the length; the first
field is the timestamp with 8 byte alignment so we need to add the
space for the extra vendor namespace presence bitmap *before* we do
any alignment for the fields.
Move the presence bitmap length accounting to the right place to fix
the alignment for the data properly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The 603 doesn't have a HASH table, TLB misses are handled by
software. It is then possible to generate page fault when
_PAGE_EXEC is not set like in nohash/32.
There is one "reserved" PTE bit available, this patch uses
it for _PAGE_EXEC.
In order to support it, set_pte_filter() and
set_access_flags_filter() are made common, and the handling
is made dependent on MMU_FTR_HPTE_TABLE
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Define slice_init_new_context_exec() at all time to avoid
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
With the following piece of code, the following compilation warning
is encountered:
if (_IOC_DIR(ioc) != _IOC_NONE) {
int verify = _IOC_DIR(ioc) & _IOC_READ ? VERIFY_WRITE : VERIFY_READ;
if (!access_ok(verify, ioarg, _IOC_SIZE(ioc))) {
drivers/platform/test/dev.c: In function 'my_ioctl':
drivers/platform/test/dev.c:219:7: warning: unused variable 'verify' [-Wunused-variable]
int verify = _IOC_DIR(ioc) & _IOC_READ ? VERIFY_WRITE : VERIFY_READ;
This patch fixes it by referencing 'type' in the macro allthough
doing nothing with it.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
commit f21f49ea63 ("[POWERPC] Remove the dregs of APUS support from
arch/powerpc") removed CONFIG_APUS, but forgot to remove the logic
which adapts tophys() and tovirt() for it.
This patch removes the last stale pieces.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch fixes the loop in p_block_mapped() and v_block_mapped()
to scan the entire bat_addrs[] array.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Depending on the CONFIG selected, many of the MMU features are
not possible. Lets only get the possible ones in MMU_FTRS_POSSIBLE.
This allows gcc to get rid at compile time of code related to
not possible features.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Use patch sites and associated helpers to manage TLB handlers
patching instead of hardcoding.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Instead of hardcoding the TLB handlers patching, use
the newly created modify_instruction_site() helper.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Use patch_sites and the new modify_instruction_site() function
instead of hardcoding hash functions patching.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Instead of manually patching a blr at hash_page() entry in
MMU_init_hw(), this patch adds a features section in head_32.S
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Use patch_site_addr() instead of hardcoding the
address calculation in machine_init()
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add two helpers to avoid hardcoding of instructions modifications.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Using patch_site_addr() helper, patch_instruction_site() and
patch_branch_site() can be simplified and inlined.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In file included from ./include/linux/hugetlb.h:445:0,
from arch/powerpc/kernel/setup-common.c:37:
./arch/powerpc/include/asm/hugetlb.h: In function ‘huge_ptep_clear_flush’:
./arch/powerpc/include/asm/hugetlb.h:154:8: error: variable ‘pte’ set but not used [-Werror=unused-but-set-variable]
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Alexei Starovoitov says:
====================
pull-request: bpf 2018-12-18
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) promote bpf_perf_event.h to mandatory UAPI header, from Masahiro.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
After phy_start() phylib takes care of all needed actions, including
aneg settings and checking link state. There's no need to set state
PHY_CHANGELINK in drivers.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
clcsock can be released while kernel_accept() references it in TCP
listen worker. Also, clcsock needs to wake up before released if TCP
fallback is used and the clcsock is blocked by accept. Add a lock to
safely release clcsock and call kernel_sock_shutdown() to wake up
clcsock from accept in smc_release().
Reported-by: syzbot+0bf2e01269f1274b4b03@syzkaller.appspotmail.com
Reported-by: syzbot+e3132895630f957306bc@syzkaller.appspotmail.com
Signed-off-by: Myungho Jung <mhjungk@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently variable data0 is not being initialized so a garbage value is
being passed to vxge_hw_vpath_fw_api and this value is being written to
the rts_access_steer_data0 register. There are other occurrances where
data0 is being initialized to zero (e.g. in function
vxge_hw_upgrade_read_version) so I think it makes sense to ensure data0
is initialized likewise to 0.
Detected by CoverityScan, CID#140696 ("Uninitialized scalar variable")
Fixes: 8424e00dfd ("vxge: serialize access to steering control register")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At least old Xen net backends seem to send frags with no real data
sometimes. In case such a fragment happens to occur with the frag limit
already reached the frontend will BUG currently even if this situation
is easily recoverable.
Modify the BUG_ON() condition accordingly.
Tested-by: Dietmar Hahn <dietmar.hahn@ts.fujitsu.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Microsemi has been bought by Microchip and Microchip is supporting those
switches.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Woojung Huh <Woojung.Huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NAME_DISTRIBUTOR messages are transmitted through unicast link on TIPC
2.0, by contrast, the messages are delivered through broadcast link on
TIPC 1.7. But at present, NAME_DISTRIBUTOR messages received by
broadcast link cannot be handled in tipc_rcv() until an unicast message
arrives, which may lead to a significant delay to update name table.
To avoid this delay, we will also deal with broadcast NAME_DISTRIBUTOR
message on broadcast receive path.
Signed-off-by: Zhenbo Gao <zhenbo.gao@windriver.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Even though the link is down before entering hibernation,
there is an issue that the network interface always links up after resuming
from hibernation.
If the link is still down before enabling the network interface,
and after resuming from hibernation, the phydev->state is forcibly set
to PHY_UP in mdio_bus_phy_restore(), and the link becomes up.
In suspend sequence, only if the PHY is attached, mdio_bus_phy_suspend()
calls phy_stop_machine(), and mdio_bus_phy_resume() calls
phy_start_machine().
In resume sequence, it's enough to do the same as mdio_bus_phy_resume()
because the state has been preserved.
This patch fixes the issue by calling phy_start_machine() in
mdio_bus_phy_restore() in the same way as mdio_bus_phy_resume().
Fixes: bc87922ff5 ("phy: Move PHY PM operations into phy_device")
Suggested-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current state for the lan78xx driver does not allow for changing the
MAC address of the interface, without either removing the module (if
you compiled it that way) or rebooting the machine. If you attempt to
change the MAC address, ifconfig will show the new address, however,
the system/interface will not respond to any traffic using that
configuration. A few short-term options to work around this are to
unload the module and reload it with the new MAC address, change the
interface to "promisc", or reboot with the correct configuration to
change the MAC.
This patch enables the ability to change the MAC address via fairly normal means...
ifdown <interface>
modify entry in /etc/network/interfaces OR a similar method
ifup <interface>
Then test via any network communication, such as ICMP requests to gateway.
My only test platform for this patch has been a raspberry pi model 3b+.
Signed-off-by: Jason Martinsen <jasonmartinsen@msn.com>
-----
Signed-off-by: David S. Miller <davem@davemloft.net>
3c1bcc8614 ("net: ethernet: Convert phydev advertize and supported
from u32 to link mode") left some unused code in phy_probe(), remove it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The LAN7431 uses an external phy, and it can be found anywhere in
the phy address space. This patch uses phy address 1 for LAN7430
only. And searches all addresses otherwise.
Signed-off-by: Bryan Whitehead <Bryan.Whitehead@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata says:
====================
vxlan: Various fixes
This patch set contains three fixes for the vxlan driver.
Patch #1 fixes handling of offload mark on replaced VXLAN FDB entries. A
way to trigger this is to replace the FDB entry with one that can not be
offloaded. A future patch set should make it possible to veto such FDB
changes. However the FDB might still fail to be offloaded due to another
issue, and the offload mark should reflect that.
Patch #2 fixes problems in __vxlan_dev_create() when a call to
rtnl_configure_link() fails. These failures would be tricky to hit on a
real system, the most likely vector is through an error in vxlan_open().
However, with the abovementioned vetoing patchset, vetoing the created
entry would trigger the same problems (and be easier to reproduce).
Patch #3 fixes a problem in vxlan_changelink(). In situations where the
default remote configured in the FDB table (if any) does not exactly
match the remote address configured at the VXLAN device, changing the
remote address breaks the default FDB entry. Patch #4 is then a self
test for this issue.
v3:
- Patch #2:
- Reuse the same errout block for both cleanup paths. Use a bool to
decide whether the unregister_netdevice() call should be made.
v2:
- Drop former patch #3
- Patch #2:
- Delete the default entry before calling unregister_netdevice(). That
takes care of former patch #3, hence tweak the commit message to
mention that problem as well.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a test to exercise the fix from the previous patch.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Default remotes are stored as FDB entries with an Ethernet address of
00:00:00:00:00:00. When a request is made to change a remote address of
a VXLAN device, vxlan_changelink() first deletes the existing default
remote, and then creates a new FDB entry.
This works well as long as the list of default remotes matches exactly
the configuration of a VXLAN remote address. Thus when the VXLAN device
has a remote of X, there should be exactly one default remote FDB entry
X. If the VXLAN device has no remote address, there should be no such
entry.
Besides using "ip link set", it is possible to manipulate the list of
default remotes by using the "bridge fdb". It is therefore easy to break
the above condition. Under such circumstances, the __vxlan_fdb_delete()
call doesn't delete the FDB entry itself, but just one remote. The
following vxlan_fdb_create() then creates a new FDB entry, leading to a
situation where two entries exist for the address 00:00:00:00:00:00,
each with a different subset of default remotes.
An even more obvious breakage rooted in the same cause can be observed
when a remote address is configured for a VXLAN device that did not have
one before. In that case vxlan_changelink() doesn't remove any remote,
and just creates a new FDB entry for the new address:
$ ip link add name vx up type vxlan id 2000 dstport 4789
$ bridge fdb ap dev vx 00:00:00:00:00:00 dst 192.0.2.20 self permanent
$ bridge fdb ap dev vx 00:00:00:00:00:00 dst 192.0.2.30 self permanent
$ ip link set dev vx type vxlan remote 192.0.2.30
$ bridge fdb sh dev vx | grep 00:00:00:00:00:00
00:00:00:00:00:00 dst 192.0.2.30 self permanent <- new entry, 1 rdst
00:00:00:00:00:00 dst 192.0.2.20 self permanent <- orig. entry, 2 rdsts
00:00:00:00:00:00 dst 192.0.2.30 self permanent
To fix this, instead of calling vxlan_fdb_create() directly, defer to
vxlan_fdb_update(). That has logic to handle the duplicates properly.
Additionally, it also handles notifications, so drop that call from
changelink as well.
Fixes: 0241b83673 ("vxlan: fix default fdb entry netlink notify ordering during netdev create")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a failure occurs in rtnl_configure_link(), the current code
calls unregister_netdevice() to roll back the earlier call to
register_netdevice(), and jumps to errout, which calls
vxlan_fdb_destroy().
However unregister_netdevice() calls transitively ndo_uninit, which is
vxlan_uninit(), and that already takes care of deleting the default FDB
entry by calling vxlan_fdb_delete_default(). Since the entry added
earlier in __vxlan_dev_create() is exactly the default entry, the
cleanup code in the errout block always leads to double free and thus a
panic.
Besides, since vxlan_fdb_delete_default() always destroys the FDB entry
with notification enabled, the deletion of the default entry is notified
even before the addition was notified.
Instead, move the unregister_netdevice() call after the manual destroy,
which solves both problems.
Fixes: 0241b83673 ("vxlan: fix default fdb entry netlink notify ordering during netdev create")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When rdst of an offloaded FDB entry is replaced, it certainly isn't
offloaded anymore. Drivers are notified about such replacements, and can
re-mark the entry as offloaded again if they so wish. However until a
driver does so explicitly, assume a replaced FDB entry is not offloaded.
Note that replaces coming via vxlan_fdb_external_learn_add() are always
immediately followed by an explicit offload marking.
Fixes: 0efe117333 ("vxlan: Support marking RDSTs as offloaded")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Or Gerlitz says:
This series is essentially a cleanup to align with the rest of the NIC
switchdev drivers and make us
more robust and clear/n: currently the PF netdev serves as the mlx5
e-switch uplink netdev
representor when going into switchdev mode and back as plain NIC
netdev when going out.
This causes some irregularities and misc troubles.
Move to use dedicated uplink rep, as we have for the VF vports.
The uplink rep netdev does has sysfs link and supports the sriov vf
mac ndo, these two are in
use by libvirt and other orchestrators, It also has richer ethtool
support to allow controlling the
port link & mtu along with supporting dcb and plugging into the mlx5
lag logic.
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJcF/MBAAoJEEg/ir3gV/o+apkIAKVeB/ha8qiY+9ntA9B8HVxO
cYb+fv4+DuYjTg/nN5QdYSAisN4SwFDA5ukz/ckr6XwV65EgTjAtlon/fHg/rDyz
YT3dJRP9yjNXKxRvxa0K4PmTasmXGXzaJzsXYemHsfCDdnkNknZsqA+yoNe+2c40
HoNsdy/Pvr18PjzYtpX0BiuSjH623daBmdFH0o+rwuwsApkAUlBJfosTg/7xyU7v
TAjy8S1HCloJ7OAjOlzXVmYr65sAlQoFr860vLDQ7Og7JemxjSXQ+AdNb6mSAvZ5
LBEvCA3G5tb4OkFX+1i/alxOcuG8/FoO+O3ZQWve1DNxoS76po851bgHXIdZCPg=
=pqTq
-----END PGP SIGNATURE-----
Merge tag 'mlx5-uplink-rep-2018-12-15' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed:
====================
mlx5-uplink-rep-2018-12-15
Or Gerlitz says:
This series is essentially a cleanup to align with the rest of the NIC
switchdev drivers and make us
more robust and clear/n: currently the PF netdev serves as the mlx5
e-switch uplink netdev
representor when going into switchdev mode and back as plain NIC
netdev when going out.
This causes some irregularities and misc troubles.
Move to use dedicated uplink rep, as we have for the VF vports.
The uplink rep netdev does has sysfs link and supports the sriov vf
mac ndo, these two are in
use by libvirt and other orchestrators, It also has richer ethtool
support to allow controlling the
port link & mtu along with supporting dcb and plugging into the mlx5
lag logic.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Anssi Hannula says:
====================
net: macb: DMA race condition fixes
Here are a couple of race condition fixes for the macb driver. The first
two are for issues observed at runtime on real HW.
v2:
- added received Tested-bys and Acked-bys to the first two patches
- in patch 3/3, moved the timestamp protection barrier closer to the
timestamp reads
- in patch 3/3, removed unnecessary move of the addr assignment in
gem_rx() to keep the patch minimal for maximum clarity
- in patch 3/3, clarified commit message and comments
The 3/3 is the same one I improperly sent last week as a standalone
patch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When reading buffer descriptors on RX or on TX completion, an
RX_USED/TX_USED bit is checked first to ensure that the descriptors have
been populated, i.e. the ownership has been transferred. However, there
are no memory barriers to ensure that the data protected by the
RX_USED/TX_USED bit is up-to-date with respect to that bit.
Specifically:
- TX timestamp descriptors may be loaded before ctrl is loaded for the
TX_USED check, which is racy as the descriptors may be updated between
the loads, causing old timestamp descriptor data to be used.
- RX ctrl may be loaded before addr is loaded for the RX_USED check,
which is racy as a new frame may be written between the loads, causing
old ctrl descriptor data to be used.
This issue exists for both macb_rx() and gem_rx() variants.
Fix the races by adding DMA read memory barriers on those paths and
reordering the reads in macb_rx().
I have not observed any actual problems in practice caused by these
being missing, though.
Tested on a ZynqMP based system.
Fixes: 89e5785fc8 ("[PATCH] Atmel MACB ethernet driver")
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bit RX_USED set to 0 in the address field allows the controller to write
data to the receive buffer descriptor.
The driver does not ensure the ctrl field is ready (cleared) when the
controller sees the RX_USED=0 written by the driver. The ctrl field might
only be cleared after the controller has already updated it according to
a newly received frame, causing the frame to be discarded in gem_rx() due
to unexpected ctrl field contents.
A message is logged when the above scenario occurs:
macb ff0b0000.ethernet eth0: not whole frame pointed by descriptor
Fix the issue by ensuring that when the controller sees RX_USED=0 the
ctrl field is already cleared.
This issue was observed on a ZynqMP based system.
Fixes: 4df95131ea ("net/macb: change RX path for GEM")
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Tested-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
64-bit DMA addresses are split in upper and lower halves that are
written in separate fields on GEM. For RX, bit 0 of the address is used
as the ownership bit (RX_USED). When the RX_USED bit is unset the
controller is allowed to write data to the buffer.
The driver does not guarantee that the controller already sees the upper
half when the RX_USED bit is cleared, possibly resulting in the
controller writing an incoming frame to an address with an incorrect
upper half and therefore possibly corrupting unrelated system memory.
Fix that by adding the necessary DMA memory barrier between the writes.
This corruption was observed on a ZynqMP based system.
Fixes: fff8019a08 ("net: macb: Add 64 bit addressing support for GEM")
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Acked-by: Harini Katakam <harini.katakam@xilinx.com>
Tested-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Herton reports the following error when building a userspace program that
includes net_stamp.h:
In file included from foo.c:2:
/usr/include/linux/net_tstamp.h:158:2: error: unknown type name
‘clockid_t’
clockid_t clockid; /* reference clockid */
^~~~~~~~~
Fix it by using __kernel_clockid_t in place of clockid_t.
Fixes: 80b14dee2b ("net: Add a new socket option for a future transmit time.")
Cc: Timothy Redaelli <tredaelli@redhat.com>
Reported-by: Herton R. Krzesinski <herton@redhat.com>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Tested-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
