The OLinuXino Lime2 has a big capacitor on its LDO3 output. It is
actually too large, causing the PMIC to shutdown when toggling the LDO3.
By enabling soft-start and ramp delay we increase the time for the
capacitor to charge lowering the current drain on the power regulator.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
In the past, there have been words on various lists that if LDO3 is
disabled in u-boot, but enabled in the DTS, the axp209 driver would
fail to continue/hang. Several enable/disable patches have been
issues to devicetree's in both the kernel and u-boot to address
this issue.
What really happened however, was that the AXP209 shuts down without
a notice and without setting an interrupt. This is caused when LDO3
gets overloaded, for example with large capacitors on the LDO3 output.
Normally, we would expect that AXP209 would source 200 mA as per
datasheet and set and trigger an interrupt when being overloaded.
For some reason however, this does not happen.
As a work-around, implement software-based 'regulator-soft-start'
property for AXP209 LDO3 regulator, which is used to first bring up
the LDO3 to the lowest possible voltage and then enable the LDO.
After that, we can set the requested voltage as usual.
Combining this setting with the regulator-ramp-delay allows LDO3 to
come up slowly and staggered, potentially reducing overall inrush current.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
In the past, there have been words on various lists that if LDO3 is
disabled in u-boot, but enabled in the DTS, the axp209 driver would
fail to continue/hang. Several enable/disable patches have been
issues to devicetree's in both the kernel and u-boot to address
this issue.
What really happened however, was that the AXP209 shuts down without
a notice and without setting an interrupt. This is caused when LDO3
gets overloaded, for example with large capacitors on the LDO3 output.
Normally, we would expect that AXP209 would source 200 mA as per
datasheet and set and trigger an interrupt when being overloaded.
For some reason however, this does not happen.
As a work-around, we use the soft-start constraint of the regulator
node to first bring up the LDO3 to the lowest possible voltage and
then enable the LDO. After that, we can set the requested voltage
as usual.
Combining this setting with the regulator-ramp-delay allows LDO3 to
enable voltage slowly and staggered, potentially reducing overall
inrush current.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The AXP209 supports ramping up voltages on several regulators such as
DCDC2 and LDO3, therefore we can use the standard 'regulator-ramp-delay'
property for those 2 regulators.
Note that the voltage ramp only works when the regulator is already
enabled. E.g. when going from say 0.7 V to 3.6 V.
When turning on the regulator, no voltage ramp is performed in hardware.
What this means, is that if the bootloader brings up the voltage at 0.7 V,
the ramp delay property is properly applied. If however, the bootloader
leaves the power off, no ramp delay is applied when the power is
enabled by the regulator framework.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Priit Laes <plaes@plaes.org>
Acked-for-MFD-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The AXP209 supports ramping up voltages on several regulators such as
DCDC2 and LDO3.
This patch adds preliminary support for the regulator-ramp-delay property
for these 2 regulators. Note that the voltage ramp only works when
regulator is already enabled. E.g. when going from say 0.7 V to 3.6 V.
When turning on the regulator, no voltage ramp is performed in hardware.
What this means, is that if the bootloader brings up the voltage at 0.7 V,
the ramp delay property is properly applied. If however, the bootloader
leaves the power off, no ramp delay is applied when the power is
enabled by the regulator framework.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The current axp20x names the ramping register 'scal' which probably
means scaling. Since the register really has nothing to do with
scaling, but really is the voltage ramp we rename it appropriately.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Priit Laes <plaes@plaes.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Even if this spdif input driver is only supposed to be used on 64bits
platform, there is possible problem with 32bits and do_div, as reported
by the kbuild robot. Just fix it.
Fixes: 5ce5658375 ("ASoC: meson: add axg spdif input")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add error logs to make probe debug easier.
Also remove hard-coded dependency on NHLT. NHLT literally stands for
NonHdaudioLinkTable and is only required for SSP/DMIC interfaces.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
bus->ppcap is now tested upfront, there is no need to re-check if the
hardware is exposed as needed. Remove tests and remove indentation.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Check immediately if required HDaudio capabilities can't be found (no
PPCAP or no streams exposed in GCAP), and move all DMA inits after the
error tests.
PPCAP and GCAP are not reliable indicators of DSP presence, but if
they don't exist then the driver will not work.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The existing PPCAP and GCAP fields cannot be used reliably to
determine if the DSP is enabled by the BIOS. Instead rely on the
class/subclass information to find out if this driver can run or
not. The values in the code don't seem to be documented in publicly
available documents but are part of recommendations made to BIOS
writers and have been verified to be accurate on a number of
platforms.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It's with CNP, supposed to be equivalent with CNL entry.
Keep the existing declaration style for now, at a later point we may
transition and use PCI_DEVICE_DATA().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Although the upper 32 bits of the PMEVTYPER<n>_EL0 registers are RES0,
we should treat the EXCLUDE_EL* bit definitions as unsigned so that we
avoid accidentally sign-extending the privilege filtering bit (bit 31)
into the upper half of the register.
Signed-off-by: Will Deacon <will.deacon@arm.com>
I2S IP instance can work in transmitter/playback or receiver/capture mode
exclusively. The patch registers corresponding instance as ASoC component
with audio framework.
Signed-off-by: Maruthi Srinivas Bayyavarapu <maruthi.srinivas.bayyavarapu@xilinx.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Added documentation for I2S IP core DT bindings.
Signed-off-by: Maruthi Srinivas Bayyavarapu <maruthi.srinivas.bayyavarapu@xilinx.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/realtek/rtlwifi/rtl8821ae/trx.c: In function 'translate_rx_signal_stuff':
drivers/net/wireless/realtek/rtlwifi/rtl8821ae/trx.c:309:6: warning:
variable 'type' set but not used [-Wunused-but-set-variable]
It never used since commit 21e4b0726d ("rtlwifi: rtl8821ae: Move driver from
staging to regular tree")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
entry is released via usb_put_urb just after calling usb_submit_urb.
However, entry is used if the submission fails, resulting in a use after
free bug. The patch fixes this.
Signed-off-by: Pan Bian <bianpan2016@163.com>
ACKed-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/broadcom/b43/phy_n.c: In function 'b43_nphy_op_recalc_txpower':
drivers/net/wireless/broadcom/b43/phy_n.c:5898:7: warning:
variable 'tx_pwr_state' set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/b43/phy_n.c:6047:20: warning:
variable 'tmp2' set but not used [-Wunused-but-set-variable]
'tx_pwr_state' never used since introduction in commit
8615eb2870 ("b43: N-PHY: support setting custom TX power")
'tmp2' not used any more since commit c002831a07 ("b43: N-PHY: use helper
for checking IPA")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When CONFIG_NO_AUTO_INLINE is set, we get a false-postive warning
for the brcmf_fw_request_nvram_done() function, after gcc figures
out that brcmf_fw_nvram_from_efi() might not set the 'data_len'
variable, but fails to notice that it always returns NULL:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/firmware.c: In function 'brcmf_fw_request_nvram_done':
drivers/net/wireless/broadcom/brcm80211/brcmfmac/firmware.c:560:11: error: 'data_len' may be used uninitialized in this function [-Werror=maybe-uninitialized]
Mark it 'inline' to force gcc to understand this.
Fixes: ce2e6db554 ("brcmfmac: Add support for getting nvram contents from EFI variables")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
AOS is a part of the SDIOD core that becomes active when the rest of
SDIOD is sleeping to keep SDIO bus alive responding to reduced set of
commands.
Transaction between AOS and SDIOD is not protected, and if cmd 52 is
received in AOS and in the middle of response state changed from AOS to
SDIOD, response is corrupted and it causes to SDIO Host controller to
hang.
Command decode for below chips are disabled in this commit:
- 4339
- 4345
- 4354
- 4373
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Double Lo <double.lo@cypress.com>
Signed-off-by: Madhan Mohan R <madhanmohan.r@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use chipcommon sr_control0 register to check 4373 sr support.
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The number of words that the read FIFO has to contain except
the end of frame before sends data back to the host.
Max watermark = (512B - 2* (BurstLength))/4 =
(512 - 128)/4 = 384/4 = 0x60
so if burst length (i.e. BurstLength = 64) is increased,
watermark has to be reduced. This is the optimal setting for this chip.
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Naveen Gupta <naveen.gupta@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
GCI core is needed for ULP operation. Allow GCI core enumuration with
below changes:
- Allow GCI to be added to core list even when it doesn't have a wrapper.
- Allow 8K address space size.
- Don't overwrite the address value when an additional size descriptor
is in place.
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
CYW43012 is a 1x1 802.11a/b/g/n Dual-Band HT20, 256-QAM/Turbo QAM. It
is an Ultra Low Power WLAN+BT combo chip.
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Praveen Babu C <praveen.chandran@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Along with F2 watermark (existing) configuration, F1 MesBusyCtrl
should be enabled & sdio device RX FIFO watermark should be
configured to avoid overflow errors.
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Madhan Mohan R <madhanmohan.r@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We got SDIO_CRC_ERROR with 4373 on SDR104 when doing bi-directional
throughput test. Enable watermark to 256 to guarantee the operation
stability.
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add the raw 4354 PCIe device ID for unprogrammed Cypress boards.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Winnie Chang <winnie.chang@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Firmware inform the driver about tx status by normal tx status signal
or compressed tx status signal. This patch adds support to handle the
compressed tx status signal.
Signed-off-by: Chung-Hsien Hsu <stanley.hsu@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The frameburst feature can enable per-packet framebursting in firmware
side and get higher TX throughput in High Throughput(HT) mode. To enhance
TX throughput, we enable frameburst mode in default firmware setting.
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The credit numbers are static and tunable per chip in firmware side.
However the credit number may be changed that is based on packet pool
length and will send BRCMF_E_FIFO_CREDIT_MAP event to notify host driver
updates the credit numbers during interface up.
The purpose of this patch is making host driver has ability of updating
the credit numbers when receiving the BRCMF_E_FIFO_CREDIT_MAP event.
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Comparing the existing TX_BITRATE parsing code (in
mwifiex_parse_htinfo()) with the RX bitrate histograms in debugfs.c, it
appears that the rxpd_rate and rxpd_htinfo fields have the same format.
At least, they give reasonable results when I parse them this way.
So this patch adds support for RX_BITRATE to our station info dump.
Along the way, I add legacy bitrate parsing into the same function,
using the debugfs code (mwifiex_histogram_read() and
mwifiex_adjust_data_rate()) as reference.
Additionally, to satisfy the requirements of
NL80211_STA_INFO_RX_BITRATE, I skip logging the bitrate of multicast
packets. This shouldn't add a lot of overhead to the RX path, as there
are already several similar 802.3 header checks in this same codepath.
We can also bias the branch behavior to favor unicast, as that's the
common performance-sensitive case.
I'd consider this support somewhat experimental, as I have zero
documentation from Marvell. But the existing driver code gives me good
reason to think this is correct.
I've tested this on a few different 802.11{a,b,g,n,ac} networks, and the
reported bitrates look good to me.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This function converts some firmware-specific parameters into cfg80211
'rate_info' structures. It currently assumes it's dealing only with TX
bitrate, but the RX bitrate looks to be the same, so refactor this
function to be reusable.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently, snippets of this file look like:
rx rates (in Mbps): 0=1M 1=2M2=5.5M 3=11M 4=6M 5=9M 6=12M
7=18M 8=24M 9=36M 10=48M 11=54M12-27=MCS0-15(BW20) 28-43=MCS0-15(BW40)
44-53=MCS0-9(VHT:BW20)54-63=MCS0-9(VHT:BW40)64-73=MCS0-9(VHT:BW80)
...
noise_flr[--96dBm] = 22
noise_flr[--95dBm] = 149
noise_flr[--94dBm] = 9
noise_flr[--93dBm] = 2
We're missing some spaces, and we're adding a minus sign ('-') on values
that are already negative signed integers.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There are two defects: (1) passing a NULL bss to
mwifiex_save_hidden_ssid_channels will result in NULL dereference,
(2) using bss after dropping the reference to it via cfg80211_put_bss.
To fix them, the patch moves the buggy code to the branch that bss is
not NULL and puts it before cfg80211_put_bss.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The new Dell IoT platform uses kabylake + alc3277 codec, and alc3277
shares the driver with the codec rt5660, here we generate a new
machine driver based on kbl_da7219_max98357a.
The audio design on this IoT platform is as below:
- Intel kabylake platform
- connect the codec ALC3277 via SSP0
- line-out and line-in with Micbias jacks
- line-out mute control and jack detection of line-out and line-in
- two HDMI ports with audio capability
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add entry for mt76 driver in MAINTAINERS file
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Starting from mac80211 commit adf8ed01e4 ("mac80211: add an optional
TXQ for other PS-buffered frames") and commit 0eeb2b674f ("mac80211:
add an option for station management TXQ") a new per-sta queue has been
introduced for bufferable management frames.
sta->txq[IEEE80211_NUM_TIDS] is initialized just if the driver reports
the following hw flags:
- IEEE80211_HW_STA_MMPDU_TXQ
- IEEE80211_HW_BUFF_MMPDU_TXQ
This can produce a NULL pointer dereference in mt76_stop_tx_queues
since mt76 iterates on all available sta tx queues assuming they are
initialized by mac80211. This issue has been spotted analyzing the code
(it has not triggered any crash yet)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
While the CSV3 field of the ID_AA64_PFR0 CPU ID register can be checked
to see if a CPU is susceptible to Meltdown and therefore requires kpti
to be enabled, existing CPUs do not implement this field.
We therefore whitelist all unaffected Cortex-A CPUs that do not implement
the CSV3 field.
Signed-off-by: Will Deacon <will.deacon@arm.com>
* use the same firmware for mt76x2e and mt76x2u
* mt76x2 fixes
* mt76x0 fixes
* mt76x0e survey support
* more unification between mt76x2 and mt76x0
* mt76x0e AP mode support
* mt76x0e DFS support
* rework and fix tx status handling for mt76x0 and mt76x2
-----BEGIN PGP SIGNATURE-----
Version: GnuPG/MacGPG2 v2
Comment: GPGTools - http://gpgtools.org
iEYEABECAAYFAlwBH4oACgkQ130UHQKnbvUdQwCdFL9rDWnaX1nvSwLZrp3DC7qD
CywAoJaygMHs0YVmXWHQ9tdEAY5i4VAO
=qF8w
-----END PGP SIGNATURE-----
Merge tag 'mt76-for-kvalo-2018-11-30' of https://github.com/nbd168/wireless
first batch of mt76 patches for 4.21
* use the same firmware for mt76x2e and mt76x2u
* mt76x2 fixes
* mt76x0 fixes
* mt76x0e survey support
* more unification between mt76x2 and mt76x0
* mt76x0e AP mode support
* mt76x0e DFS support
* rework and fix tx status handling for mt76x0 and mt76x2
kvalo: fixed a conflict in drivers/net/wireless/mediatek/mt76/mt76x2/pci_main.c
and a build problem in drivers/net/wireless/mediatek/mt76/mt76x02_util.c
This reverts commit 5188d5453b, because it
introduced lock recursion:
BUG: spinlock recursion on CPU#2, kworker/u13:1/395
lock: 0xffffffc0e28a47f0, .magic: dead4ead, .owner: kworker/u13:1/395, .owner_cpu: 2
CPU: 2 PID: 395 Comm: kworker/u13:1 Not tainted 4.20.0-rc4+ #2
Hardware name: Google Kevin (DT)
Workqueue: MWIFIEX_RX_WORK_QUEUE mwifiex_rx_work_queue [mwifiex]
Call trace:
dump_backtrace+0x0/0x140
show_stack+0x20/0x28
dump_stack+0x84/0xa4
spin_bug+0x98/0xa4
do_raw_spin_lock+0x5c/0xdc
_raw_spin_lock_irqsave+0x38/0x48
mwifiex_flush_data+0x2c/0xa4 [mwifiex]
call_timer_fn+0xcc/0x1c4
run_timer_softirq+0x264/0x4f0
__do_softirq+0x1a8/0x35c
do_softirq+0x54/0x64
netif_rx_ni+0xe8/0x120
mwifiex_recv_packet+0xfc/0x10c [mwifiex]
mwifiex_process_rx_packet+0x1d4/0x238 [mwifiex]
mwifiex_11n_dispatch_pkt+0x190/0x1ac [mwifiex]
mwifiex_11n_rx_reorder_pkt+0x28c/0x354 [mwifiex]
mwifiex_process_sta_rx_packet+0x204/0x26c [mwifiex]
mwifiex_handle_rx_packet+0x15c/0x16c [mwifiex]
mwifiex_rx_work_queue+0x104/0x134 [mwifiex]
worker_thread+0x4cc/0x72c
kthread+0x134/0x13c
ret_from_fork+0x10/0x18
This was clearly not tested well at all. I simply performed 'wget' in a
loop and it fell over within a few seconds.
Fixes: 5188d5453b ("mwifiex: restructure rx_reorder_tbl_lock usage")
Cc: <stable@vger.kernel.org>
Cc: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With commit 0a9f8f0a1b ("rtlwifi: fix btmpinfo timeout while processing
C2H_BT_INFO"), calling rtl_c2hcmd_enqueue() with rtl_c2h_fast_cmd() true,
the routine returns without freeing that skb, thereby leaking it.
This issue has been discussed at https://github.com/lwfinger/rtlwifi_new/issues/401
and the fix tested there.
Fixes: 0a9f8f0a1b ("rtlwifi: fix btmpinfo timeout while processing C2H_BT_INFO")
Reported-and-tested-by: Francisco Machado Magalhães Neto <franmagneto@gmail.com>
Cc: Francisco Machado Magalhães Neto <franmagneto@gmail.com>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Stable <stable@vger.kernel.org> # 4.18+
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds a regulator driver for the MCP16502 PMIC.
This drivers supports basic operations through the
regulator interface such as:
- setting/reading voltage
- setting/reading operating mode
- reading current status
Signed-off-by: Andrei Stefanescu <andrei.stefanescu@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds a maintainer for the MCP16502 PMIC
driver.
Signed-off-by: Andrei Stefanescu <andrei.stefanescu@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch describes the compatible and the device tree
bindings necessary for the MCP16502 PMIC.
Signed-off-by: Andrei Stefanescu <andrei.stefanescu@microchip.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for the spdif input decoder of the axg SoC family
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
