When parallel bus is used and data-active is being parsed, incorrect
flags are cleared.
Clear the correct flag bits.
Fixes: e9be1b863e (media: v4l: fwnode:
Use default parallel flags).
Cc: stable@vger.kernel.org # for Kernel 4.20
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When support for bonding of RoCE devices was added, there was
necessarily a link between the RoCE device and the paired netdevice that
was part of the bond. If you remove the mlx4_en module, that paired
association is broken (the RoCE device is still present but the paired
netdevice has been released). We need to account for this in
is_upper_ndev_bond_master_filter() and filter out those links with a
broken pairing or else we later oops in netdev_next_upper_dev_rcu().
Fixes: 408f1242d9 ("IB/core: Delete lower netdevice default GID entries in bonding scenario")
Signed-off-by: Mark Zhang <markz@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The Video Engine (VE) embedded in the Aspeed AST2400 and AST2500 SOCs
can capture and compress video data from digital or analog sources. With
the Aspeed chip acting a service processor, the Video Engine can capture
the host processor graphics output.
Add a V4L2 driver to capture video data and compress it to JPEG images.
Make the video frames available through the V4L2 streaming interface.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add documentation for regulator modes and suspend states.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Implement shutdown method to make sure the PMIC will not enter the suspend
state when the system is shutdown.
This work is based on work done by Borris Brezillon on [1].
[1] https://www.spinics.net/lists/kernel/msg2942960.html
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix line over 80 chars checkpatch.pl warning.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The regulator supports a dedicated suspend mode.
Implement the appropriate ->set_suspend_xx() hooks, add support for
->set_mode(), and provide basic PM ops functionalities to setup the
regulator in a suspend state when the system is entering suspend.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
[claudiu.beznea@microchip.com: remove shutdown function, use dev_pm_ops,
fix checkpatch warning, adapt commit message, add LDO modes support,
move modes constants to active-semi,8945a-regulator.h, remove rdevs from
struct act8945a_pmic, add op_mode to act8945a_pmic]
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Unlock expert registers for act8945a.
This is based on orginal work of Boris Brezillon at [1].
[1] https://www.spinics.net/lists/kernel/msg2942960.html
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
After making sure that the regulator core always take over
handling of the GPIO descriptors, the gpiod_put()
on the errorpath of the Arizona LDO1 driver becomes
redundant.
Reported-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
After making sure that the regulator core always take over
handling of the GPIO descriptors, the gpiod_put()
on the errorpath of the wm8994 driver becomes redundant.
Reported-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Document the bindings.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Current rsnd is using RSND_REG_xxx for register naming,
and using RSND_REG_##f style macro for read/write.
The biggest reason why it uses this style is that
we can avoid non-existing register access.
But, its demerit is sequential register access code will
be very ugly.
Current rsnd driver is well tested, so, let's remove RSND_REG_
from rsnd_reg, and cleanup sequential register access code.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch fixes I2C transfers in Cadence I3C master driver.
There was no way to queue more than one I2C transfer before.
Fixes: 603f2bee2c ("i3c: master: Add driver for Cadence IP")
Signed-off-by: Przemyslaw Gaj <pgaj@cadence.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Wire up the basic support for hot-adding memory. Since memory hotplug
is fairly tightly coupled to sparsemem, we tweak pfn_valid() to also
cross-check the presence of a section in the manner of the generic
implementation, before falling back to memblock to check for no-map
regions within a present section as before. By having arch_add_memory(()
create the linear mapping first, this then makes everything work in the
way that __add_section() expects.
We expect hotplug to be ACPI-driven, so the swapper_pg_dir updates
should be safe from races by virtue of the global device hotplug lock.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Commit 959bf2fd03 ("arm64: percpu: Rewrite per-cpu ops to allow use of
LSE atomics") introduced alternative code sequences for the arm64 percpu
atomics, so that the LSE instructions can be patched in at runtime if
they are supported by the CPU.
Unfortunately, when patching in the LSE sequence for a value-returning
pcpu atomic, the argument registers are the wrong way round. The
implementation of this_cpu_add_return() therefore ends up adding
uninitialised stack to the percpu variable and returning garbage.
As it turns out, there aren't very many users of the value-returning
percpu atomics in mainline and we only spotted this due to a failure in
the kprobes selftests. In this case, when attempting to single-step over
the out-of-line instruction slot, the debug monitors would not be
enabled because calling this_cpu_inc_return() on the kernel debug
monitor refcount would fail to detect the transition from 0. We would
consequently execute past the slot and take an undefined instruction
exception from the kernel, resulting in a BUG:
| kernel BUG at arch/arm64/kernel/traps.c:421!
| PREEMPT SMP
| pc : do_undefinstr+0x268/0x278
| lr : do_undefinstr+0x124/0x278
| Process swapper/0 (pid: 1, stack limit = 0x(____ptrval____))
| Call trace:
| do_undefinstr+0x268/0x278
| el1_undef+0x10/0x78
| 0xffff00000803c004
| init_kprobes+0x150/0x180
| do_one_initcall+0x74/0x178
| kernel_init_freeable+0x188/0x224
| kernel_init+0x10/0x100
| ret_from_fork+0x10/0x1c
Fix the argument order to get the value-returning pcpu atomics working
correctly when implemented using the LSE instructions.
Reported-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Decoupled version bump from commit f6c367585d ("dm thin: send event
about thin-pool state change _after_ making it") because version bumps
just create conflicts when backporting to the stable trees.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
While we can export symbols from assembly files, CONFIG_MODVERIONS requires C
declarations of anyhting that's exported.
Let's account for this as other architectures do by placing these declarations
in <asm/asm-prototypes.h>, which kbuild will automatically use to generate
modversion information for assembly files.
Since we already define most prototypes in existing headers, we simply need to
include those headers in <asm/asm-prototypes.h>, and don't need to duplicate
these.
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Fix up licensing to be inline with Linux conventions.
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
NULL check before some freeing functions is not needed.
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
With the introduction of 52-bit virtual addressing for userspace, we are
now in a position where the virtual addressing capability of userspace
may exceed that of the kernel. Consequently, the VA_BITS definition
cannot be used blindly, since it reflects only the size of kernel
virtual addresses.
This patch introduces MAX_USER_VA_BITS which is either VA_BITS or 52
depending on whether 52-bit virtual addressing has been configured at
build time, removing a few places where the 52 is open-coded based on
explicit CONFIG_ guards.
Signed-off-by: Will Deacon <will.deacon@arm.com>
The return statement is redundant as there is a return statement
immediately before it so we have dead code that can be removed.
Also remove the unused declaration of ret.
Detected by CoverityScan, CID#1473793 ("Structurally dead code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
The API to configure a PWM using pwm_enable(), pwm_disable(),
pwm_config() and pwm_set_polarity() is superseeded by atomically setting
the parameters using pwm_apply_state(). To get forward with deprecating
the former set of functions use the opportunity that there is no current
user of pwm_set_polarity() and remove it.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Implement the get_state() function and set the initial state to reflect
real state of the hardware. This allows to keep the PWM running if it was
enabled in bootloader. It is very similar to the GPIO behavior. GPIO pin
set as output in bootloader keep the same setting in Linux unless it is
reconfigured.
If we find the PWM block enabled we need to prepare and enable its source
clock otherwise the clock will be disabled late in the boot as unused.
That will leave the PWM in enabled state but with disabled clock. That has
a side effect that the PWM output is left at its current level at which
the clock was disabled. It is totally non-deterministic and it may be LOW
or HIGH.
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Use existing macros to define register fields instead of manually shifting
the bit masks. Also define some more register bits.
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Adding an extra MI_STORE_DWORD_IMM to the gpu relocation path for gen3
was good, but still not good enough. To survive 24+ hours under test we
needed to perform not one, not two but three extra store-dw. Doing so
for each GPU relocation was a little unsightly and since we need to
worry about userspace hitting the same issues, we should apply the dummy
store-dw into the EMIT_FLUSH.
Fixes: 7dd4f6729f ("drm/i915: Async GPU relocation processing")
References: 7fa28e1469 ("drm/i915: Write GPU relocs harder with gen3")
Testcase: igt/gem_tiled_fence_blits # blb/pnv
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181207134037.11848-1-chris@chris-wilson.co.uk
(cherry picked from commit a889580c08)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Currently we allocate a scratch page for each engine, but since we only
ever write into it for post-sync operations, it is not exposed to
userspace nor do we care for coherency. As we then do not care about its
contents, we can use one page for all, reducing our allocations and
avoid complications by not assuming per-engine isolation.
For later use, it simplifies engine initialisation (by removing the
allocation that required struct_mutex!) and means that we can always rely
on there being a scratch page.
v2: Check that we allocated a large enough scratch for I830 w/a
Fixes: 06e562e7f515 ("drm/i915/ringbuffer: Delay after EMIT_INVALIDATE for gen4/gen5") # v4.18.20
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=108850
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181204141522.13640-1-chris@chris-wilson.co.uk
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: <stable@vger.kernel.org> # v4.18.20+
(cherry picked from commit 5179749925)
[Joonas: Use new function in gen9_init_indirectctx_bb too]
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Braswell is really picky about having our writes posted to memory before
we execute or else the GPU may see stale values. A wmb() is insufficient
as it only ensures the writes are visible to other cores, we need a full
mb() to ensure the writes are in memory and visible to the GPU.
The most frequent failure in flushing before execution is that we see
stale PTE values and execute the wrong pages.
References: 987abd5c62 ("drm/i915/execlists: Force write serialisation into context image vs execution")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181206084431.9805-3-chris@chris-wilson.co.uk
(cherry picked from commit 490b8c65b9)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Ido Schimmel says:
====================
mlxsw: Add Spectrum-2 multicast routing support
Nir says:
In Spectrum the firmware provided an abstraction for multicast routing
on top of the policy engine. In Spectrum-2 this is no longer the case
and the driver must interact directly with the policy engine in order to
program multicast routes. Every route is written as an ACL rule, its
priority set according to route type (*,G) or (S,G) and its action is an
appropriate multicast routing action. Multicast routes are written to a
specific ACL group which is bound to the appropriate IP protocol
IPv4/IPv6.
Patch #1 adds PEMRBT register needed to declare which ACL group is
dedicated for each IP protocol multicast routing function.
Patch #2 Changes initialization order and puts ACL before router as
multicast router now uses ACL module.
Patch #3 adds Spectrum-2 ACL keys needed for multicast route matching.
Patch #4 adds another ACL profile - in addition to existing flower
profile - which allows the multicast routing module to program rules
directly into the ACL block.
Patch #5 adds the ability to update ACL rules' action, since multicast
routes actions may be updated after being configured.
Patch #6 separates rule creation operation and rule action creation
operation as in multicast router the action is created before the route
is inserted.
Patch #7 sharpens priority handling in Spectrum-2, to ensure incorrect
values are not set to rule's priority.
Patch #8 adds the implementation of multicast routing for IPv4 and IPv6
over existing ACL rule programming
Finally, patch #9 adds a test for IPv4/IPv6 multicast routing.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce basic testing for both IPv4 and IPv6 multicast. The test creates
an (S,G) type route, sends traffic and verifies traffic arrives when the
route is present and then verifies traffic does not arrive after deleting
the route.
This test requires smcroute - https://github.com/troglobit/smcroute which
is a tool that allows creation of static multicast routes.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add implementation of Spectrum-2 multicast routes for both IPv4 and IPv6 by
using ACL module explicitly.
In Spectrum-2, multicast routes are set as ACL rules, so initialization
takes care of creating dedicated ACL groups and binding them to the
appropriate multicast routing protocol IPv4/IPv6, and afterwards routes
configuration translates to setting explicit ACL rules.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In Spectrum-2, higher priority value wins and priority valid values are in
the range of {1,cap_kvd_size-1}. mlxsw_sp_acl_tcam_priority_get converts
from lower-bound priorities alike tc flower to Spectrum-2 HW range. Up
until now tc flower did not provide priority 0 or reached the maximal
value, however multicast routing does provide priority 0.
Therefore, Change mlxsw_sp_acl_tcam_priority_get to verify priority is in
the correct range. Make sure priority is never set to zero and never
exceeds the maximal allowed value.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Up until now, when ACL rule was created its action was created with it.
It suits well for tc flower where ACL rule always needs an action, however
it does not suit multicast router, where the action is created prior to
setting a route, which in Spectrum-2 is actually an ACL rule.
Add support for rule creation without action creation. Do it by adding
afa_block argument to mlxsw_sp_acl_rule_create, which if NULL then an
action would be created, also add an indication within struct
mlxsw_sp_acl_rule_info that tells if the action should be destroyed when
the rule is destroyed.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Multicast routes actions may be updated after creation. An example for that
is an addition of an egress interface to an existing route.
So far, as tc flower API dictated, ACL rules were either created or
deleted. Since multicast routes in Spectrum-2 are written to ACL as any
rule, it is required to allow the update of a rule's action as it may
change.
Add methods and operations to support updating rule's action. This is
supported only for Spectrum-2.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add specific ACL operations needed for programming multicast routing ACL
groups and routes.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add virtual router ID fields to Spectrum-2 key blocks set, as the field is
required for multicast routing.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In Spectrum-2, MC routing is implemented using ACL block explicitly, so
router initialization should take place after ACL initialization.
Set the initialization of the ACL block before IP router initizalization
takes place, so multicast router will be able to allocate ACL data
structures and create its required chains.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In Spectrum-2, multicast routing is implemented explicitly using policy
engine (ACL) block. PEMRBT register is used to bind a dedicated ACL group
to a specific IP protocol.
Add the register to be later used in multicast router implementation.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Noticed this while working on redoing the reference counting scheme in
the DP MST helpers. Nouveau doesn't attempt to call
drm_dp_mst_topology_mgr_destroy() at all, which leaves it leaking all of
the resources for drm_dp_mst_topology_mgr and it's children mstbs+ports.
Fixes: f479c0ba4a ("drm/nouveau/kms/nv50: initial support for DP 1.2 multi-stream")
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: <stable@vger.kernel.org> # v4.10+
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Should hopefully fix a regression some people have been seeing since EVO
push buffers were moved to VRAM by default on Pascal GPUs.
Fixes: d00ddd9da ("drm/nouveau/kms/nv50-: allocate push buffers in vidmem on pascal")
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Cc: <stable@vger.kernel.org> # 4.19+
If CONFIG_DEBUG_SHIRQ is enabled __free_irq() intentionally fires
a spurious interrupt. This interrupt causes a crash because
tp->dev->phydev is NULL at that time.
Fixes: 38caff5a44 ("r8169: handle all interrupt events in the hard irq handler")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to schedule a different tasklet for refill,
This patch remove it.
Suggested-by: Neil Horman <nhorman@redhat.com>
Signed-off-by: Xue Chaojing <xuechaojing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael and Sandipan report:
Commit ede95a63b5 introduced a bpf_jit_limit tuneable to limit BPF
JIT allocations. At compile time it defaults to PAGE_SIZE * 40000,
and is adjusted again at init time if MODULES_VADDR is defined.
For ppc64 kernels, MODULES_VADDR isn't defined, so we're stuck with
the compile-time default at boot-time, which is 0x9c400000 when
using 64K page size. This overflows the signed 32-bit bpf_jit_limit
value:
root@ubuntu:/tmp# cat /proc/sys/net/core/bpf_jit_limit
-1673527296
and can cause various unexpected failures throughout the network
stack. In one case `strace dhclient eth0` reported:
setsockopt(5, SOL_SOCKET, SO_ATTACH_FILTER, {len=11, filter=0x105dd27f8},
16) = -1 ENOTSUPP (Unknown error 524)
and similar failures can be seen with tools like tcpdump. This doesn't
always reproduce however, and I'm not sure why. The more consistent
failure I've seen is an Ubuntu 18.04 KVM guest booted on a POWER9
host would time out on systemd/netplan configuring a virtio-net NIC
with no noticeable errors in the logs.
Given this and also given that in near future some architectures like
arm64 will have a custom area for BPF JIT image allocations we should
get rid of the BPF_JIT_LIMIT_DEFAULT fallback / default entirely. For
4.21, we have an overridable bpf_jit_alloc_exec(), bpf_jit_free_exec()
so therefore add another overridable bpf_jit_alloc_exec_limit() helper
function which returns the possible size of the memory area for deriving
the default heuristic in bpf_jit_charge_init().
Like bpf_jit_alloc_exec() and bpf_jit_free_exec(), the new
bpf_jit_alloc_exec_limit() assumes that module_alloc() is the default
JIT memory provider, and therefore in case archs implement their custom
module_alloc() we use MODULES_{END,_VADDR} for limits and otherwise for
vmalloc_exec() cases like on ppc64 we use VMALLOC_{END,_START}.
Additionally, for archs supporting large page sizes, we should change
the sysctl to be handled as long to not run into sysctl restrictions
in future.
Fixes: ede95a63b5 ("bpf: add bpf_jit_limit knob to restrict unpriv allocations")
Reported-by: Sandipan Das <sandipan@linux.ibm.com>
Reported-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Tested-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
A decoy address is used by set_mce_nospec() to update the cache attributes
for a page that may contain poison (multi-bit ECC error) while attempting
to minimize the possibility of triggering a speculative access to that
page.
When reserve_memtype() is handling a decoy address it needs to convert it
to its real physical alias. The conversion, AND'ing with __PHYSICAL_MASK,
is broken for a 32-bit physical mask and reserve_memtype() is passed the
last physical page. Gert reports triggering the:
BUG_ON(start >= end);
...assertion when running a 32-bit non-PAE build on a platform that has
a driver resource at the top of physical memory:
BIOS-e820: [mem 0x00000000fff00000-0x00000000ffffffff] reserved
Given that the decoy address scheme is only targeted at 64-bit builds and
assumes that the top of physical address space is free for use as a decoy
address range, simply bypass address sanitization in the 32-bit case.
Lastly, there was no need to crash the system when this failure occurred,
and no need to crash future systems if the assumptions of decoy addresses
are ever violated. Change the BUG_ON() to a WARN() with an error return.
Fixes: 510ee090ab ("x86/mm/pat: Prepare {reserve, free}_memtype() for...")
Reported-by: Gert Robben <t2@gert.gr>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Gert Robben <t2@gert.gr>
Cc: stable@vger.kernel.org
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: platform-driver-x86@vger.kernel.org
Cc: <stable@vger.kernel.org>
Link: https://lkml.kernel.org/r/154454337985.789277.12133288391664677775.stgit@dwillia2-desk3.amr.corp.intel.com
This patch enables arm64's bpf_int_jit_compile() to provide
bpf_line_info by calling bpf_prog_fill_jited_linfo().
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Commit f149b31557 ("signal: Never allocate siginfo for SIGKILL or SIGSTOP")
means that the seccomp selftest cannot check si_pid under SIGSTOP anymore.
Since it's believed[1] there are no other userspace things depending on the
old behavior, this removes the behavioral check in the selftest, since it's
more a "extra" sanity check (which turns out, maybe, not to have been
useful to test).
[1] https://lkml.kernel.org/r/CAGXu5jJaZAOzP1qFz66tYrtbuywqb+UN2SOA1VLHpCCOiYvYeg@mail.gmail.com
Reported-by: Tycho Andersen <tycho@tycho.ws>
Suggested-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Shuah Khan <shuah@kernel.org>
