mirror of
https://github.com/BobTheBlinker/android_kernel_motorola_sm6375.git
synced 2026-11-12 01:51:34 -05:00
32be3e931e
The need for this modification comes from the hardware team. Increase wled ovp and ocp, otherwise new board and panel may trigger ovp fault, cause backlight can't work. Change-Id: Iabaff8d1cdc91730d0e9f01db14d56f36d397e70 Signed-off-by: houdz1 <[email protected]> Reviewed-on: https://gerrit.mot.com/2001706 SME-Granted: SME Approvals Granted SLTApproved: Slta Waiver Tested-by: Jira Key Reviewed-by: Huosheng Liao <[email protected]> Submit-Approved: Jira Key
269 lines
7.3 KiB
Devicetree
269 lines
7.3 KiB
Devicetree
|
|
#include "dsi-panel-mot-auo-nt36675-fhd-video.dtsi"
|
|
#include "dsi-panel-mot-boe-nt36675-fhd-video.dtsi"
|
|
#include "dsi-panel-mot-dummy-qhd-video.dtsi"
|
|
#include "dsi-panel-mot-bod-nt36675-fhd-video.dtsi"
|
|
|
|
|
|
|
|
&pm6150a_amoled {
|
|
status = "disabled";
|
|
};
|
|
|
|
&pm6150l_lcdb {
|
|
status = "ok"
|
|
};
|
|
|
|
&pm6150l_wled {
|
|
status = "ok"
|
|
|
|
qcom,string-cfg = <7>;
|
|
|
|
qcom,fs-current-limit = <25000>;
|
|
qcom,en-cabc;
|
|
qcom,cabc-sel = <1>;
|
|
|
|
qcom,wled-bl-step-up;
|
|
qcom,wled-bl-step-sequence = <255 5>, <2048 6>;
|
|
|
|
qcom,ovp = <26500>;
|
|
qcom,boost-current-limit = <1400>;
|
|
|
|
mmi,only-low-bl-force-cabc-disable;
|
|
mmi,low-bl-threshold = <200>;
|
|
mmi,low-bl-remap-percent = <69>;
|
|
};
|
|
|
|
&sde_dsi {
|
|
lab-supply = <&lcdb_ldo_vreg>;
|
|
ibb-supply = <&lcdb_ncp_vreg>;
|
|
vddio-supply = <&L1E>;
|
|
|
|
qcom,dsi-default-panel = <&dsi_nt36675_auo_video>;
|
|
};
|
|
|
|
&mdss_dsi_phy0 {
|
|
qcom,platform-strength-ctrl = [55 03 30 30
|
|
55 03 30 30
|
|
55 03 30 30
|
|
55 03 30 30
|
|
55 00 30 30];
|
|
};
|
|
|
|
&soc {
|
|
dsi_panel_pwr_supply_denver: dsi_panel_pwr_supply_denver{
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
qcom,panel-supply-entry@0 {
|
|
reg = <0>;
|
|
qcom,supply-name = "vddio";
|
|
qcom,supply-min-voltage = <1800000>;
|
|
qcom,supply-max-voltage = <1904000>;
|
|
qcom,supply-enable-load = <32000>;
|
|
qcom,supply-disable-load = <80>;
|
|
qcom,supply-post-on-sleep= <0>;
|
|
qcom,supply-post-off-sleep = <21>;
|
|
};
|
|
|
|
qcom,panel-supply-entry@1 {
|
|
reg = <1>;
|
|
qcom,supply-name = "lab";
|
|
qcom,supply-min-voltage = <5800000>;
|
|
qcom,supply-max-voltage = <5800000>;
|
|
qcom,supply-enable-load = <100000>;
|
|
qcom,supply-disable-load = <100>;
|
|
qcom,supply-pre-on-sleep = <3>;
|
|
};
|
|
|
|
qcom,panel-supply-entry@2 {
|
|
reg = <2>;
|
|
qcom,supply-name = "ibb";
|
|
qcom,supply-min-voltage = <5800000>;
|
|
qcom,supply-max-voltage = <5800000>;
|
|
qcom,supply-enable-load = <100000>;
|
|
qcom,supply-disable-load = <100>;
|
|
qcom,supply-pre-off-sleep = <3>;
|
|
qcom,supply-post-on-sleep = <3>;
|
|
};
|
|
};
|
|
|
|
dsi_panel_pwr_supply_denver_boe: dsi_panel_pwr_supply_denver_boe{
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
qcom,panel-supply-entry@0 {
|
|
reg = <0>;
|
|
qcom,supply-name = "vddio";
|
|
qcom,supply-min-voltage = <1800000>;
|
|
qcom,supply-max-voltage = <1904000>;
|
|
qcom,supply-enable-load = <32000>;
|
|
qcom,supply-disable-load = <80>;
|
|
qcom,supply-post-on-sleep= <0>;
|
|
qcom,supply-post-off-sleep = <21>;
|
|
};
|
|
|
|
qcom,panel-supply-entry@1 {
|
|
reg = <1>;
|
|
qcom,supply-name = "lab";
|
|
qcom,supply-min-voltage = <5500000>;
|
|
qcom,supply-max-voltage = <5500000>;
|
|
qcom,supply-enable-load = <100000>;
|
|
qcom,supply-disable-load = <100>;
|
|
qcom,supply-pre-on-sleep = <3>;
|
|
};
|
|
|
|
qcom,panel-supply-entry@2 {
|
|
reg = <2>;
|
|
qcom,supply-name = "ibb";
|
|
qcom,supply-min-voltage = <5500000>;
|
|
qcom,supply-max-voltage = <5500000>;
|
|
qcom,supply-enable-load = <100000>;
|
|
qcom,supply-disable-load = <100>;
|
|
qcom,supply-pre-off-sleep = <3>;
|
|
qcom,supply-post-on-sleep = <3>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&dsi_nt36675_auo_video {
|
|
qcom,platform-te-gpio = <&tlmm 23 0>;
|
|
qcom,platform-reset-gpio = <&pm6150l_gpios 9 0>;
|
|
|
|
qcom,panel-supply-entries = <&dsi_panel_pwr_supply_denver>;
|
|
|
|
qcom,mdss-dsi-bl-pmic-control-type = "bl_ctrl_wled";
|
|
|
|
qcom,mdss-dsi-bl-min-level = <32>;
|
|
qcom,mdss-dsi-bl-max-level = <4095>;
|
|
qcom,mdss-dsi-bl-default-level = <2047>;
|
|
qcom,mdss-brightness-max-level = <4095>;
|
|
|
|
qcom,esd-check-enabled;
|
|
qcom,mdss-dsi-panel-status-check-mode = "reg_read";
|
|
qcom,mdss-dsi-panel-status-command = [06 01 00 01 00 00 01 0a];
|
|
qcom,mdss-dsi-panel-status-command-state = "dsi_hs_mode";
|
|
qcom,mdss-dsi-panel-status-value = <0x9c>;
|
|
qcom,mdss-dsi-panel-status-read-length = <1>;
|
|
|
|
qcom,tp_state_check_enable;
|
|
|
|
qcom,mdss-dsi-hbm-on-command = [39 01 00 00 00 00 03 51 0F FF];
|
|
qcom,mdss-dsi-hbm-on-command-state = "dsi_lp_mode";
|
|
qcom,mdss-dsi-hbm-off-command = [39 01 00 00 00 00 03 51 0B 13];
|
|
qcom,mdss-dsi-hbm-off-command-state = "dsi_lp_mode";
|
|
qcom,mdss-dsi-hbm-type = "lcd-dcs-wled";
|
|
|
|
qcom,dsi-select-clocks = "mux_byte_clk0", "mux_pixel_clk0";
|
|
qcom,mdss-dsi-t-clk-post = <0x0F>;
|
|
qcom,mdss-dsi-t-clk-pre = <0x3B>;
|
|
qcom,mdss-dsi-display-timings {
|
|
timing@0 {
|
|
qcom,mdss-dsi-panel-phy-timings = [00 24 0A 0A 26 25 09
|
|
0A 09 02 04 00];
|
|
qcom,display-topology = <1 0 1>;
|
|
qcom,default-topology-index = <0>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&dsi_nt36675_boe_video {
|
|
qcom,platform-te-gpio = <&tlmm 23 0>;
|
|
qcom,platform-reset-gpio = <&pm6150l_gpios 9 0>;
|
|
|
|
qcom,panel-supply-entries = <&dsi_panel_pwr_supply_denver_boe>;
|
|
|
|
qcom,mdss-dsi-bl-pmic-control-type = "bl_ctrl_wled";
|
|
|
|
qcom,mdss-dsi-bl-min-level = <32>;
|
|
qcom,mdss-dsi-bl-max-level = <4095>;
|
|
qcom,mdss-dsi-bl-default-level = <2047>;
|
|
qcom,mdss-brightness-max-level = <4095>;
|
|
|
|
qcom,esd-check-enabled;
|
|
qcom,mdss-dsi-panel-status-check-mode = "reg_read";
|
|
qcom,mdss-dsi-panel-status-command = [06 01 00 01 00 00 01 0a];
|
|
qcom,mdss-dsi-panel-status-command-state = "dsi_hs_mode";
|
|
qcom,mdss-dsi-panel-status-value = <0x9c>;
|
|
qcom,mdss-dsi-panel-status-read-length = <1>;
|
|
|
|
qcom,tp_state_check_enable;
|
|
|
|
qcom,mdss-dsi-hbm-on-command = [39 01 00 00 00 00 03 51 0F FF];
|
|
qcom,mdss-dsi-hbm-on-command-state = "dsi_lp_mode";
|
|
qcom,mdss-dsi-hbm-off-command = [39 01 00 00 00 00 03 51 0B 13];
|
|
qcom,mdss-dsi-hbm-off-command-state = "dsi_lp_mode";
|
|
qcom,mdss-dsi-hbm-type = "lcd-dcs-wled";
|
|
|
|
qcom,dsi-select-clocks = "mux_byte_clk0", "mux_pixel_clk0";
|
|
qcom,mdss-dsi-t-clk-post = <0x0F>;
|
|
qcom,mdss-dsi-t-clk-pre = <0x3B>;
|
|
qcom,mdss-dsi-display-timings {
|
|
timing@0 {
|
|
qcom,mdss-dsi-panel-phy-timings = [00 24 0A 0A 26 25 09
|
|
0A 09 02 04 00];
|
|
qcom,display-topology = <1 0 1>;
|
|
qcom,default-topology-index = <0>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&dsi_nt36675_bod_video {
|
|
qcom,platform-te-gpio = <&tlmm 23 0>;
|
|
qcom,platform-reset-gpio = <&pm6150l_gpios 9 0>;
|
|
|
|
qcom,panel-supply-entries = <&dsi_panel_pwr_supply_denver_boe>;
|
|
|
|
qcom,mdss-dsi-bl-pmic-control-type = "bl_ctrl_wled";
|
|
|
|
qcom,mdss-dsi-bl-min-level = <32>;
|
|
qcom,mdss-dsi-bl-max-level = <4095>;
|
|
qcom,mdss-dsi-bl-default-level = <2047>;
|
|
qcom,mdss-brightness-max-level = <4095>;
|
|
|
|
qcom,esd-check-enabled;
|
|
qcom,mdss-dsi-panel-status-check-mode = "reg_read";
|
|
qcom,mdss-dsi-panel-status-command = [06 01 00 01 00 00 01 0a];
|
|
qcom,mdss-dsi-panel-status-command-state = "dsi_hs_mode";
|
|
qcom,mdss-dsi-panel-status-value = <0x9c>;
|
|
qcom,mdss-dsi-panel-status-read-length = <1>;
|
|
|
|
qcom,tp_state_check_enable;
|
|
|
|
qcom,mdss-dsi-hbm-on-command = [39 01 00 00 00 00 03 51 0F FF];
|
|
qcom,mdss-dsi-hbm-on-command-state = "dsi_lp_mode";
|
|
qcom,mdss-dsi-hbm-off-command = [39 01 00 00 00 00 03 51 0B 13];
|
|
qcom,mdss-dsi-hbm-off-command-state = "dsi_lp_mode";
|
|
qcom,mdss-dsi-hbm-type = "lcd-dcs-wled";
|
|
|
|
qcom,dsi-select-clocks = "mux_byte_clk0", "mux_pixel_clk0";
|
|
qcom,mdss-dsi-t-clk-post = <0x0F>;
|
|
qcom,mdss-dsi-t-clk-pre = <0x3B>;
|
|
qcom,mdss-dsi-display-timings {
|
|
timing@0 {
|
|
qcom,mdss-dsi-panel-phy-timings = [00 24 0A 0A 26 25 09
|
|
0A 09 02 04 00];
|
|
qcom,display-topology = <1 0 1>;
|
|
qcom,default-topology-index = <0>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&mot_dummy_vid_qhd {
|
|
qcom,platform-te-gpio = <&tlmm 23 0>;
|
|
qcom,platform-reset-gpio = <&pm6150l_gpios 9 0>;
|
|
|
|
qcom,panel-supply-entries = <&dsi_panel_pwr_supply_denver>;
|
|
|
|
qcom,dsi-select-clocks = "mux_byte_clk0", "mux_pixel_clk0";
|
|
qcom,mdss-dsi-t-clk-post = <0x09>;
|
|
qcom,mdss-dsi-t-clk-pre = <0x15>;
|
|
qcom,mdss-dsi-display-timings {
|
|
timing@0 {
|
|
qcom,mdss-dsi-panel-phy-timings = [00 0B 02 02 1C 1C 03
|
|
02 01 02 04 00];
|
|
qcom,display-topology = <1 0 1>;
|
|
qcom,default-topology-index = <0>;
|
|
};
|
|
};
|
|
};
|