mirror of
https://github.com/BobTheBlinker/android_kernel_motorola_sm6375.git
synced 2026-11-12 10:01:54 -05:00
40526282ad
PMIC PM8008 LDOs do not support low power mode (LPM). If configured for LPM, these LDOs continue to operate in normal power mode (NPM) with the same quiescent current but a reduced over-current protection (OCP) threshold, which can result in OCP triggering. Fix all PM8008 LDOs to use normal power mode (NPM) alone to avoid this. Change-Id: I2c8961eaba0677768da09aeba577a32810c1d50f
524 lines
11 KiB
Devicetree
524 lines
11 KiB
Devicetree
#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
|
|
#include <dt-bindings/interrupt-controller/irq.h>
|
|
#include <dt-bindings/iio/qti_power_supply_iio.h>
|
|
|
|
#include "pm6350.dtsi"
|
|
#include "pm7250b.dtsi"
|
|
#include "pm6150l.dtsi"
|
|
|
|
#define PMK8350_SID 6
|
|
|
|
#include "pmk8350.dtsi"
|
|
|
|
&pm6350_gpios {
|
|
key_vol_up {
|
|
key_vol_up_default: key_vol_up_default {
|
|
pins = "gpio2";
|
|
function = "normal";
|
|
input-enable;
|
|
bias-pull-up;
|
|
power-source = <0>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&pm7250b_vadc {
|
|
charger_skin_therm {
|
|
reg = <ADC5_AMUX_THM1_100K_PU>;
|
|
label = "charger_skin_therm";
|
|
qcom,ratiometric;
|
|
qcom,hw-settle-time = <200>;
|
|
qcom,pre-scaling = <1 1>;
|
|
};
|
|
|
|
conn_therm {
|
|
reg = <ADC5_AMUX_THM3_100K_PU>;
|
|
label = "conn_therm";
|
|
qcom,ratiometric;
|
|
qcom,hw-settle-time = <200>;
|
|
qcom,pre-scaling = <1 1>;
|
|
};
|
|
};
|
|
|
|
&pm7250b_adc_tm {
|
|
io-channels = <&pm7250b_vadc ADC5_AMUX_THM1_100K_PU>,
|
|
<&pm7250b_vadc ADC5_AMUX_THM3_100K_PU>;
|
|
|
|
/* Channel nodes */
|
|
charger_skin_therm {
|
|
reg = <ADC5_AMUX_THM1_100K_PU>;
|
|
qcom,ratiometric;
|
|
qcom,hw-settle-time = <200>;
|
|
};
|
|
|
|
conn_therm {
|
|
reg = <ADC5_AMUX_THM3_100K_PU>;
|
|
qcom,ratiometric;
|
|
qcom,hw-settle-time = <200>;
|
|
};
|
|
};
|
|
|
|
&pm6150l_vadc {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <
|
|
&rfc_cam_therm_default
|
|
&rear_cam_flash_therm_default
|
|
&quiet_therm_default>;
|
|
|
|
pa_therm2 {
|
|
reg = <ADC5_AMUX_THM1_100K_PU>;
|
|
label = "pa_therm2";
|
|
qcom,ratiometric;
|
|
qcom,hw-settle-time = <200>;
|
|
qcom,pre-scaling = <1 1>;
|
|
};
|
|
|
|
msm_therm {
|
|
reg = <ADC5_AMUX_THM2_100K_PU>;
|
|
label = "msm_therm";
|
|
qcom,ratiometric;
|
|
qcom,hw-settle-time = <200>;
|
|
qcom,pre-scaling = <1 1>;
|
|
};
|
|
|
|
pa_therm1 {
|
|
reg = <ADC5_AMUX_THM3_100K_PU>;
|
|
label = "pa_therm1";
|
|
qcom,ratiometric;
|
|
qcom,hw-settle-time = <200>;
|
|
qcom,pre-scaling = <1 1>;
|
|
};
|
|
|
|
rfc_cam_therm {
|
|
reg = <ADC5_GPIO2_100K_PU>;
|
|
label = "rfc_cam_therm";
|
|
qcom,ratiometric;
|
|
qcom,hw-settle-time = <200>;
|
|
qcom,pre-scaling = <1 1>;
|
|
};
|
|
|
|
rear_cam_flash_therm {
|
|
reg = <ADC5_GPIO3_100K_PU>;
|
|
label = "rear_cam_flash_therm";
|
|
qcom,ratiometric;
|
|
qcom,hw-settle-time = <200>;
|
|
qcom,pre-scaling = <1 1>;
|
|
};
|
|
|
|
quiet_therm {
|
|
reg = <ADC5_GPIO4_100K_PU>;
|
|
label = "quiet_therm";
|
|
qcom,ratiometric;
|
|
qcom,hw-settle-time = <200>;
|
|
qcom,pre-scaling = <1 1>;
|
|
};
|
|
};
|
|
|
|
&pm6150l_gpios {
|
|
rfc_cam_therm {
|
|
rfc_cam_therm_default: rfc_cam_therm_default {
|
|
pins = "gpio6";
|
|
bias-high-impedance;
|
|
};
|
|
};
|
|
|
|
rear_cam_flash_therm {
|
|
rear_cam_flash_therm_default: rear_cam_flash_therm_default {
|
|
pins = "gpio7";
|
|
bias-high-impedance;
|
|
};
|
|
};
|
|
|
|
quiet_therm {
|
|
quiet_therm_default: quiet_therm_default {
|
|
pins = "gpio10";
|
|
bias-high-impedance;
|
|
};
|
|
};
|
|
};
|
|
|
|
&pm6150l_adc_tm {
|
|
io-channels = <&pm6150l_vadc ADC5_AMUX_THM1_100K_PU>,
|
|
<&pm6150l_vadc ADC5_AMUX_THM3_100K_PU>,
|
|
<&pm6150l_vadc ADC5_GPIO3_100K_PU>,
|
|
<&pm6150l_vadc ADC5_GPIO4_100K_PU>;
|
|
|
|
/* Channel nodes */
|
|
pa_therm1 {
|
|
reg = <ADC5_AMUX_THM1_100K_PU>;
|
|
qcom,ratiometric;
|
|
qcom,hw-settle-time = <200>;
|
|
};
|
|
|
|
pa_therm0 {
|
|
reg = <ADC5_AMUX_THM3_100K_PU>;
|
|
qcom,ratiometric;
|
|
qcom,hw-settle-time = <200>;
|
|
};
|
|
|
|
rear_cam_flash_therm {
|
|
reg = <ADC5_GPIO3_100K_PU>;
|
|
qcom,ratiometric;
|
|
qcom,hw-settle-time = <200>;
|
|
};
|
|
|
|
quiet_therm {
|
|
reg = <ADC5_GPIO4_100K_PU>;
|
|
qcom,ratiometric;
|
|
qcom,hw-settle-time = <200>;
|
|
};
|
|
};
|
|
|
|
&spmi_bus {
|
|
qcom,pm6150l@4 {
|
|
pm6150l_adc_tm_iio: adc_tm@3400 {
|
|
compatible = "qcom,adc-tm5-iio";
|
|
reg = <0x3400>;
|
|
#thermal-sensor-cells = <1>;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
io-channels = <&pm6150l_vadc ADC5_AMUX_THM2_100K_PU>,
|
|
<&pm6150l_vadc ADC5_GPIO2_100K_PU>;
|
|
|
|
msm_therm {
|
|
reg = <ADC5_AMUX_THM2_100K_PU>;
|
|
qcom,ratiometric;
|
|
qcom,hw-settle-time = <200>;
|
|
};
|
|
|
|
rfc_cam_therm {
|
|
reg = <ADC5_GPIO2_100K_PU>;
|
|
qcom,ratiometric;
|
|
qcom,hw-settle-time = <200>;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&pmk8350 {
|
|
reg = <6 SPMI_USID>;
|
|
|
|
pon_pbs@800 {
|
|
status = "disabled";
|
|
};
|
|
|
|
pon_hlos@1300 {
|
|
status = "disabled";
|
|
};
|
|
};
|
|
|
|
&pmk8350_rtc {
|
|
interrupts = <0x6 0x62 0x1 IRQ_TYPE_EDGE_RISING>;
|
|
};
|
|
|
|
&pmk8350_vadc {
|
|
interrupts = <0x6 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
|
|
|
|
/delete-node/ pm8350_ref_gnd;
|
|
/delete-node/ pm8350_vref_1p25;
|
|
/delete-node/ pm8350_die_temp;
|
|
/delete-node/ pm8350_vph_pwr;
|
|
|
|
/delete-node/ pm8350b_ref_gnd;
|
|
/delete-node/ pm8350b_vref_1p25;
|
|
/delete-node/ pm8350b_die_temp;
|
|
/delete-node/ pm8350b_vph_pwr;
|
|
/delete-node/ pm8350b_vbat_sns;
|
|
|
|
/delete-node/ pmr735a_ref_gnd;
|
|
/delete-node/ pmr735a_vref_1p25;
|
|
/delete-node/ pmr735a_die_temp;
|
|
|
|
/delete-node/ pmr735b_ref_gnd;
|
|
/delete-node/ pmr735b_vref_1p25;
|
|
/delete-node/ pmr735b_die_temp;
|
|
};
|
|
|
|
&pmk8350_adc_tm {
|
|
interrupts = <0x6 0x34 0x0 IRQ_TYPE_EDGE_RISING>;
|
|
io-channels = <&pmk8350_vadc PMK8350_ADC7_AMUX_THM1_100K_PU>;
|
|
|
|
xo_therm {
|
|
reg = <PMK8350_ADC7_AMUX_THM1_100K_PU>;
|
|
qcom,ratiometric;
|
|
qcom,hw-settle-time = <200>;
|
|
};
|
|
};
|
|
|
|
&flash_led {
|
|
status = "ok"
|
|
io-channels = <&pm7250b_qg PSY_IIO_RESISTANCE>,
|
|
<&pm7250b_qg PSY_IIO_VOLTAGE_OCV>,
|
|
<&pm7250b_qg PSY_IIO_CURRENT_NOW>,
|
|
<&pm7250b_charger PSY_IIO_FLASH_TRIGGER>,
|
|
<&pm7250b_charger PSY_IIO_FLASH_ACTIVE>;
|
|
io-channel-names = "rbatt",
|
|
"voltage_ocv",
|
|
"current_now",
|
|
"flash_trigger",
|
|
"flash_active";
|
|
};
|
|
|
|
&pm6150l_wled {
|
|
io-channels = <&pm7250b_qg PSY_IIO_RESISTANCE>,
|
|
<&pm7250b_qg PSY_IIO_VOLTAGE_OCV>,
|
|
<&pm7250b_qg PSY_IIO_CURRENT_NOW>;
|
|
io-channel-names = "rbatt",
|
|
"voltage_ocv",
|
|
"current_now";
|
|
};
|
|
|
|
&thermal_zones {
|
|
chg-skin-therm-usr {
|
|
polling-delay-passive = <0>;
|
|
polling-delay = <0>;
|
|
thermal-governor = "user_space";
|
|
thermal-sensors = <&pm7250b_adc_tm ADC5_AMUX_THM1_100K_PU>;
|
|
wake-capable-sensor;
|
|
trips {
|
|
active-config0 {
|
|
temperature = <125000>;
|
|
hysteresis = <1000>;
|
|
type = "passive";
|
|
};
|
|
};
|
|
};
|
|
|
|
conn-therm-usr {
|
|
polling-delay-passive = <0>;
|
|
polling-delay = <0>;
|
|
thermal-governor = "user_space";
|
|
thermal-sensors = <&pm7250b_adc_tm ADC5_AMUX_THM3_100K_PU>;
|
|
wake-capable-sensor;
|
|
trips {
|
|
active-config0 {
|
|
temperature = <125000>;
|
|
hysteresis = <1000>;
|
|
type = "passive";
|
|
};
|
|
};
|
|
};
|
|
|
|
sdm-skin-therm-usr {
|
|
polling-delay-passive = <0>;
|
|
polling-delay = <0>;
|
|
thermal-governor = "user_space";
|
|
thermal-sensors = <&pm6150l_adc_tm_iio ADC5_AMUX_THM2_100K_PU>;
|
|
wake-capable-sensor;
|
|
trips {
|
|
active-config0 {
|
|
temperature = <125000>;
|
|
hysteresis = <1000>;
|
|
type = "passive";
|
|
};
|
|
};
|
|
};
|
|
|
|
rfc-cam-pa3-usr {
|
|
polling-delay-passive = <0>;
|
|
polling-delay = <0>;
|
|
thermal-governor = "user_space";
|
|
thermal-sensors = <&pm6150l_adc_tm_iio ADC5_GPIO2_100K_PU>;
|
|
wake-capable-sensor;
|
|
trips {
|
|
active-config0 {
|
|
temperature = <125000>;
|
|
hysteresis = <1000>;
|
|
type = "passive";
|
|
};
|
|
};
|
|
};
|
|
|
|
camera-therm-usr {
|
|
polling-delay-passive = <0>;
|
|
polling-delay = <0>;
|
|
thermal-governor = "user_space";
|
|
thermal-sensors = <&pm6150l_adc_tm ADC5_GPIO3_100K_PU>;
|
|
wake-capable-sensor;
|
|
trips {
|
|
active-config0 {
|
|
temperature = <125000>;
|
|
hysteresis = <1000>;
|
|
type = "passive";
|
|
};
|
|
};
|
|
};
|
|
|
|
quiet-therm-usr {
|
|
polling-delay-passive = <0>;
|
|
polling-delay = <0>;
|
|
thermal-governor = "user_space";
|
|
thermal-sensors = <&pm6150l_adc_tm ADC5_GPIO4_100K_PU>;
|
|
wake-capable-sensor;
|
|
trips {
|
|
active-config0 {
|
|
temperature = <125000>;
|
|
hysteresis = <1000>;
|
|
type = "passive";
|
|
};
|
|
|
|
active-config1 {
|
|
temperature = <125000>;
|
|
hysteresis = <1000>;
|
|
type = "passive";
|
|
};
|
|
};
|
|
};
|
|
|
|
pa-therm0-usr {
|
|
polling-delay-passive = <0>;
|
|
polling-delay = <0>;
|
|
thermal-governor = "user_space";
|
|
thermal-sensors = <&pm6150l_adc_tm ADC5_AMUX_THM3_100K_PU>;
|
|
wake-capable-sensor;
|
|
trips {
|
|
active-config0 {
|
|
temperature = <125000>;
|
|
hysteresis = <1000>;
|
|
type = "passive";
|
|
};
|
|
};
|
|
};
|
|
|
|
pa-therm1-usr {
|
|
polling-delay-passive = <0>;
|
|
polling-delay = <0>;
|
|
thermal-governor = "user_space";
|
|
thermal-sensors = <&pm6150l_adc_tm ADC5_AMUX_THM1_100K_PU>;
|
|
wake-capable-sensor;
|
|
trips {
|
|
active-config0 {
|
|
temperature = <125000>;
|
|
hysteresis = <1000>;
|
|
type = "passive";
|
|
};
|
|
};
|
|
};
|
|
|
|
xo-therm-usr {
|
|
polling-delay-passive = <0>;
|
|
polling-delay = <0>;
|
|
thermal-governor = "user_space";
|
|
thermal-sensors = <&pmk8350_adc_tm PMK8350_ADC7_AMUX_THM1_100K_PU>;
|
|
wake-capable-sensor;
|
|
trips {
|
|
active-config0 {
|
|
temperature = <125000>;
|
|
hysteresis = <1000>;
|
|
type = "passive";
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&qupv3_se10_i2c {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
status = "ok"
|
|
|
|
pm8008_8: qcom,pm8008@8 {
|
|
compatible = "qcom,i2c-pmic";
|
|
reg = <0x8>;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&pm8008_active>;
|
|
|
|
pm8008_chip: qcom,pm8008-chip@900 {
|
|
compatible = "qcom,pm8008-chip";
|
|
reg = <0x900>;
|
|
|
|
PM8008_EN: qcom,pm8008-chip-en {
|
|
regulator-name = "pm8008-chip-en";
|
|
};
|
|
};
|
|
|
|
qcom,revid@100 {
|
|
compatible = "qcom,qpnp-revid";
|
|
reg = <0x100>;
|
|
};
|
|
};
|
|
|
|
pm8008_9: qcom,pm8008@9 {
|
|
compatible = "qcom,i2c-pmic";
|
|
reg = <0x9>;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
pm8008_regulators: qcom,pm8008-regulator {
|
|
compatible = "qcom,pm8008-regulator";
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
pm8008_en-supply = <&PM8008_EN>;
|
|
|
|
vdd_l1_l2-supply = <&S8E>;
|
|
vdd_l3_l4-supply = <&BOB>;
|
|
vdd_l5-supply = <&BOB>;
|
|
vdd_l6-supply = <&S2A>;
|
|
vdd_l7-supply = <&BOB>;
|
|
|
|
L1P: qcom,pm8008-l1@4000 {
|
|
reg = <0x4000>;
|
|
regulator-name = "pm8008_l1";
|
|
regulator-min-microvolt = <528000>;
|
|
regulator-max-microvolt = <1200000>;
|
|
qcom,min-dropout-voltage = <120000>;
|
|
qcom,hpm-min-load = <0>;
|
|
};
|
|
|
|
L2P: qcom,pm8008-l2@4100 {
|
|
reg = <0x4100>;
|
|
regulator-name = "pm8008_l2";
|
|
regulator-min-microvolt = <528000>;
|
|
regulator-max-microvolt = <1056000>;
|
|
qcom,min-dropout-voltage = <200000>;
|
|
qcom,hpm-min-load = <0>;
|
|
};
|
|
|
|
L3P: qcom,pm8008-l3@4200 {
|
|
reg = <0x4200>;
|
|
regulator-name = "pm8008_l3";
|
|
regulator-min-microvolt = <1500000>;
|
|
regulator-max-microvolt = <2800000>;
|
|
qcom,min-dropout-voltage = <192000>;
|
|
qcom,hpm-min-load = <0>;
|
|
};
|
|
|
|
L4P: qcom,pm8008-l4@4300 {
|
|
reg = <0x4300>;
|
|
regulator-name = "pm8008_l4";
|
|
regulator-min-microvolt = <1500000>;
|
|
regulator-max-microvolt = <2880000>;
|
|
qcom,min-dropout-voltage = <160000>;
|
|
qcom,hpm-min-load = <0>;
|
|
};
|
|
|
|
L5P: qcom,pm8008-l5@4400 {
|
|
reg = <0x4400>;
|
|
regulator-name = "pm8008_l5";
|
|
regulator-min-microvolt = <1500000>;
|
|
regulator-max-microvolt = <2800000>;
|
|
qcom,min-dropout-voltage = <296000>;
|
|
qcom,hpm-min-load = <0>;
|
|
};
|
|
|
|
L6P: qcom,pm8008-l6@4400 {
|
|
reg = <0x4500>;
|
|
regulator-name = "pm8008_l6";
|
|
regulator-min-microvolt = <1500000>;
|
|
regulator-max-microvolt = <1800000>;
|
|
qcom,min-dropout-voltage = <72000>;
|
|
qcom,hpm-min-load = <0>;
|
|
};
|
|
|
|
L7P: qcom,pm8008-l7@4400 {
|
|
reg = <0x4600>;
|
|
regulator-name = "pm8008_l7";
|
|
regulator-min-microvolt = <1500000>;
|
|
regulator-max-microvolt = <2800000>;
|
|
qcom,min-dropout-voltage = <112000>;
|
|
qcom,hpm-min-load = <0>;
|
|
};
|
|
};
|
|
};
|
|
};
|