sm8250-common: update gps configs from RRA31.Q3-18-86

Change-Id: I3c7197a9c872469b01866dff1984f09293d24694

gps/etc/apdr.conf

@@ -0,0 +1,205 @@
+# AP DR SENSOR Configuration file
+#
+# SENSOR_SERVICE options are one of below
+#   accel,gyro,vehicle_accel,vehicle_gyro,pedometer,vehicle_odometry,accel_temp,
+#   gyro_temp,baro,mag_calib,mag_uncalib,amd,rmd.
+#
+# SENSOR_PROVIDER options is one of -- default,native,ssc,samlite.
+#
+# SENSOR_RATE = 1~100 (Hz)
+#
+# SENSOR_SAMPLES = 1~N
+#
+# SENSOR_STATISTIC_ENABLED
+#  bit 0: Diag Print Enabled
+#  bit 1: Adb  Print Enabled
+# SENSOR_STATISTIC_PRINT_COUNT
+#  Skip Number of Print
+#
+# QDR_DYNAMIC_LOADING = 1~3
+# Configure QDR library to be loaded
+#   1: QDR3
+#   2: QDR2-GYRO
+#   3: QDR2-DWT
+#
+#
+
+
+######################################
+#                                    #
+#   Default Configuration            #
+#  (GNSS only,QDR Disabled)          #
+#                                    #
+# For QDR enablement, comment        #
+# this section and enabled           #
+# either QDR3 OR                     #
+# QDR2-DWT OR QDR2-Gyro related      #
+# configuration section in below.    #
+#                                    #
+######################################
+
+SENSOR_SERVICE = accel
+SENSOR_PROVIDER = native
+SENSOR_RATE = 100
+SENSOR_SAMPLES = 1
+
+SENSOR_SERVICE = gyro
+SENSOR_PROVIDER = native
+SENSOR_RATE = 100
+SENSOR_SAMPLES = 1
+
+SENSOR_SERVICE = vehicle_gear
+SENSOR_PROVIDER = native
+SENSOR_RATE = 100
+SENSOR_SAMPLES = 1
+
+
+######################################
+#                                    #
+#   QDR3 Configuration               #
+#                                    #
+# For QDR3,                          #
+# comment default configuration above#
+# and                                #
+# uncomment below configuration      #
+# settings.                          #
+#                                    #
+######################################
+#
+#SENSOR_SERVICE = accel
+#SENSOR_PROVIDER = native
+#SENSOR_RATE = 10
+#SENSOR_SAMPLES = 10
+#
+#SENSOR_SERVICE = vehicle_speed
+#SENSOR_PROVIDER = native
+#SENSOR_RATE = 100
+#SENSOR_SAMPLES = 1
+#
+#SENSOR_SERVICE = gyro
+#SENSOR_PROVIDER = native
+#SENSOR_RATE = 10
+#SENSOR_SAMPLES = 10
+#
+#SENSOR_SERVICE = vehicle_gear
+#SENSOR_PROVIDER = native
+#SENSOR_RATE = 100
+#SENSOR_SAMPLES = 1
+#
+#
+##Enable/disable sensor data flashback feature
+#QDR_FLASHBACK_ENABLED = 0
+##Configure QDR library to be loaded 1: QDR3 2: QDR2-GYRO 3: QDR2-DWS
+#QDR_DYNAMIC_LOADING = 1
+##Enable/disable sensor data batching feature
+#QDR_BATCHING_ENABLED = 2
+##Reporting offset before PPS boundary
+#QDR_REPORTING_OFFSET = 0
+##Sensor dispatch threshold declaration
+#QDR_SENSDISPATCH_MS = 30
+#
+
+######################################
+#                                    #
+#   QDR2-DWT Configuration           #
+#                                    #
+# For QDR2-DWT,                      #
+# comment default configuration above#
+# and                                #
+# uncomment below configuration      #
+# settings.                          #
+#                                    #
+######################################
+#
+#SENSOR_SERVICE = vehicle_speed
+#SENSOR_PROVIDER = native
+#SENSOR_RATE = 100
+#SENSOR_SAMPLES = 1
+#SENSOR_STATISTIC_ENABLED = 3
+#SENSOR_STATISTIC_PRINT_COUNT = 50
+#
+#SENSOR_SERVICE = vehicle_dws
+#SENSOR_PROVIDER = native
+#SENSOR_RATE = 100
+#SENSOR_SAMPLES = 1
+#SENSOR_STATISTIC_ENABLED = 3
+#SENSOR_STATISTIC_PRINT_COUNT = 50
+#
+#SENSOR_SERVICE = vehicle_gear
+#SENSOR_PROVIDER = native
+#SENSOR_RATE = 100
+#SENSOR_SAMPLES = 1
+#SENSOR_STATISTIC_ENABLED = 3
+#SENSOR_STATISTIC_PRINT_COUNT = 50
+#
+#GNSS_POS_STATISTIC_ENABLED = 3
+#GNSS_POS_STATISTIC_PRNTCNT = 10
+#GNSS_MSR_STATISTIC_ENABLED = 3
+#GNSS_MSR_STATISTIC_PRNTCNT = 10
+#
+##Enable/disable sensor data flashback feature
+#QDR_FLASHBACK_ENABLED = 0
+##Configure QDR library to be loaded 1: QDR3 2: QDR2-GYRO 3: QDR2-DWS
+#QDR_DYNAMIC_LOADING = 3
+##Enable/disable sensor data batching feature
+#QDR_BATCHING_ENABLED = 0
+##Reporting offset before PPS boundary
+#QDR_REPORTING_OFFSET = 0
+##Sensor dispatch threshold declaration
+#QDR_SENSDISPATCH_MS = 30
+##QDR_ENABLE_QG shall be set as 1
+#QDR_ENABLE_QG = 1
+##Select Wheel set (E.g.: Front two wheels, Rear two wheels OR All four wheels)
+##To be used for differential wheel tick OR speed service.
+##This configuration is applicable when QDR_CAN_TYPE configured as
+##ODO_DWS(3) or ODO_DWT(2).
+##Value "0": Use Front two wheels
+##Value "1": Use Rear two wheels
+##Value "2": Use All four wheels
+#QG_DRIVE_WHEEL_FW_RW_AW = 2
+##Max Wheel tick value above which wheel tick rolls over
+##This configuration is applicable when QDR_CAN_TYPE configured as ODO_DWT(2)
+#QG_DWT_MAX_WHEEL_TICK_COUNT = 255.0
+##Configure Wheel constant for DWT based below equation
+##(2 * pi * WHEEL_RADIUS / Pulses Per revolution)
+##This configuration is applicable when QDR_CAN_TYPE configured as ODO_DWT(2)
+#QG_DWT_WHEEL_CONSTANT = 0.044
+
+######################################
+#                                    #
+#   QDR2-GYRO Configuration          #
+#                                    #
+# For QDR2-GYRO,                     #
+# comment default configuration above#
+# and                                #
+# uncomment below configuration      #
+# settings.                          #
+#                                    #
+######################################
+#
+#SENSOR_SERVICE = vehicle_speed
+#SENSOR_PROVIDER = native
+#SENSOR_RATE = 100
+#SENSOR_SAMPLES = 1
+#
+#SENSOR_SERVICE = vehicle_gyro
+#SENSOR_PROVIDER = native
+#SENSOR_RATE = 100
+#SENSOR_SAMPLES = 1
+#
+#SENSOR_SERVICE = vehicle_gear
+#SENSOR_PROVIDER = native
+#SENSOR_RATE = 100
+#SENSOR_SAMPLES = 1
+#
+##Enable/disable sensor data flashback feature
+#QDR_FLASHBACK_ENABLED = 0
+##Configure QDR library to be loaded 1: QDR3 2: QDR2-GYRO 3: QDR2-DWS
+#QDR_DYNAMIC_LOADING = 2
+##Enable/disable sensor data batching feature
+#QDR_BATCHING_ENABLED = 0
+##Reporting offset before PPS boundary
+#QDR_REPORTING_OFFSET = 0
+##Sensor dispatch threshold declaration
+#QDR_SENSDISPATCH_MS = 30
+#