Merge commit '1e0b2efd0c' into android12-5.4-lahaina

* commit '1e0b2efd0c':
  ARM: dts: msm: Modify GPIO28 functionality as per pinctrl change
  ARM: dts: msm: Disable LPM States for SDXLEMUR + QCN9000
  ARM: dts: msm: Limit the PCIe speed to Gen3 for sdxlemur
  bindings: power: reset: Add qcom-dload-mode bindings for SDX65
  ARM: dts: msm: Add BOOT_CONFIG register offset for sdxlemur
  ARM: dts: msm: Updating the PHY version for sdxlemur
  ARM: dts: qcom: Set right IRQ type to MHI interrupt
  ARM: dts: msm: Fix ipq attach property for sdx driver
  ARM: dts: msm: correct SSCTL instance ID for SMP2P shutdown ack from modem
  ARM: dts: msm: Enable ipa register dump collection
  ARM: dts: msm: Enable sdx-ext-ipc driver
  ARM: dts: msm: Remove mpm wakeup control capability for yupik
  ARM: dts: msm: Reducing throughput thresholds
  ARM: dts: msm: Enable focaltech touch node for r66451 on Blair CDP
  ARM: dts: msm: Added delay for Napa PHY to come of reset
  ARM: dts: msm: Update the modem size to 102MB
  ARM: dts: msm: Add LPM info for menu governor
  ARM: dts: msm: Added delay for AQR113 PHY to come of reset
  ARM: dts: msm: Add LPM info for menu governor
  ARM: dts: qcom: Enable QCN9000 nodes for sdxlemur-mtp-cpe-pine2x
  ARM: dts: msm: Add additional v2 variant for sdxlemur board
  ARM: dts: qcom: add mode control for S8B regulator for yupik
  ARM: dts: msm: Enable subsystem_sleep_stats driver for lahaina
  dt-bindings: subsystem_sleep_stats: reg is optional property
  dt-bindings: subsystem_sleep_stats: Add reg as required property
  dt-bindings: thermal: Add snapshot of devfreq-vdd-cdev
  ARM: dts: msm: update thermal config for sdxlemur
  ARM: dts: msm: remove gfx-cdev for blair
  ARM: dts: msm: add devfreq-vdd-cdev cooling device and remove gfx-cdev
  dt-bindings: thermal: Add snapshot of modem cdev dt binding
  ARM: dts: msm: update modem qmi sensor name
  ARM: dts: qcom: Update mdm tsens thermal config for sdxlemur
  ARM: dts: msm: Remove IOSS interface from AQC, RTL and QPS615
  ARM: dts: msm: Enable smmu s1 for blsp bam on sdxlemur V2
  ARM: dts: msm: Enable bluetooth for sdxlemur CPE variants
  ARM: dts: qcom: reduce L4B regulator min voltage to 880 mV for sdxlemur
  ARM: dts: qcom: EP GPIO reset mask update
  ARM: dts: qcom: PCIe REFCLK always on
  ARM: dts: msm: Ensure PCIe device is not in D3hot during reboot
  ARM: dts: msm: Enable WOL for QCA8081 on sdxlemur
  ARM: dts: msm: Enable WAKE_PHY for AQR113 on sdxlemur
  ARM: dts: qcom: Fix qrtr_instance_id and qrtr_node_id for QCN9000
  Revert "Revert "ARM: dts: msm: PCIe turn-on of NTN3 regulator""
  ARM: dts: msm: Add IOSS channels directly under device
  ARM: dts: msm: Set default_gen_speed to 0
  ARM: dts: msm: Enable best fit algo on sdxlemur
  ARM: dts: msm: Includes cnss devicetree dtsi file
  ARM: dts: msm: Add support for ETH nodes
  ARM: dts: msm: Enable USB2/PCIE for yupik iot with pm7250b
  ARM: dts: msm: Add AQC and R8125 dtsi nodes
  Revert "ARM: dts: msm: PCIe turn-on of NTN3 regulator"
  ARM: dts: msm: Modify the usb dma address pool on sdxlemur
  ARM: dts: msm: PHY regulator ramp delays
  ARM: dts: msm: Set the interrupt moderation interval to 1ms on sdxlemur
  ARM: dts: msm: Enable bluetooth for sdxlemur mtp cpe
  ARM: dts: qcom: PCIe to Gen3 , DSP2 HSP in Gen2
  ARM: dts: msm: Correct lpi offset table for holi
  ARM: dts: msm: Add additional v2 variants for sdxlemur boards
  ARM: dts: msm: correction to the cps related properties
  ARM: dts: msm: Add pil modem regulator for sdxlemur v2
  ARM: dts: msm: Revise V2 dts and add sdxlemur lite soc id
  ARM: dts: msm: Modify cpufreq to ddrfreq table
  ARM: dts: msm: Bump up cpu frequency
  ARM: dts: msm: Update of RC PCIe PHY settings to V1.08 for sdxlemur
  ARM: dts: msm: Update of EP PCIe PHY settings to V1.08 for sdxlemur
  ARM: dts: qcom: Disabling dt node for sdx ipc driver
  ARM: dts: msm: Remove BT property bt-sw-ctrl-gpio for sdxlemur
  ARM: dts: msm: Update smmu s1 mask on sdxlemur V2
  ARM: dts: qcom: Add separate cpu dai for mi2s rx and tx
  ARM: dts: msm: PHY reset GPIO properties
  ARM: dts: msm: Update compatible for HSP on Yupik
  ARM: dts: qcom: Set default_gen_speed as gen3 for sdx65
  ARM: dts: msm: Enable KPDPWR status logging
  dt-bindings: input: qpnp-power-on: Add qcom,log-kpd-event description
  ARM: dts: msm: Pin config for AQR on MBB
  ARM: dts: msm: PCIe turn-on of NTN3 regulator
  ARM: dts: msm: PHY supply DTSI properties
  ARM: dts: qcom: Enable link enumeration via perst
  ARM: dts: msm: disable LAN RX NAPI
  ARM: dts: msm: Separating AQR & Napa Ring descriptions
  ARM: dts: msm: Update CPU frequencies for sdxlemur v2
  ARM: dts: msm: WoL IRQ support for AQR
  ARM: dts: msm: add ntn3 ipa pcie changes for MBB
  ARM: dts: msm: Enable separate IPA instance ID and IOMMU group for Napa
  ARM: dts: msm: Add GPU revision for Yupik A643 target
  ARM: dts: msm: Add pm7250b dts variant for yupik iot
  ARM: dts: msm: WoL IRQ support for AQR and Napa PHYs
  ARM: dts: qcom: Remove redundant entries in sdxlemur-qcn9000.dtsi
  ARM: dts: msm: Enable bluetooth for v2 sdxlemur
  ARM: dts: msm: Disable L1 mode on sdxlemur ep variants
  ARM: dts: msm: Skip BW vote for PM8008 used I2C SE node
  ARM: dts: msm: Add keepalive flag for QUP for Blair/Holi
  ARM: dts: msm: Prevent PM8008 LPM usage for all targets
  ARM: dts: msm: add nvmem cell for PMK8350 SDAM23 adc scaling
  ARM: dts: msm: Add support for HSP BT SoC
  ARM: dts: msm: put ipa_eth_group1 in bypass mode
  ARM: dts: msm: Remove support for PCIE1 and USB3_SEC clocks on YUPIK HSP
  ARM: dts: qcom: Add support to read ibat_external_range from nvmem for yupik
  dt-bindings: thermal: Add support to scale ibat current range to bcl driver
  ARM: dts: msm: Add HSP property in CNSS DT Node
  ARM: dts: msm: Add gpu-models property for yupik gpu
  ARM: dts: msm: Add CNSS DT Node for HSP support
  ARM: dts: qcom: Add IPA register for QCN9000
  ARM: dts: msm: Add support for HSP for Yupik
  ARM: dts: msm: Remove separate DT for digital mics for Yupik
  ARM: dts: msm: Restore SDCC registers once Resuming from CX/XO
  ARM: dts: msm: Add keepalive flag for QUP for Blair/Holi
  ARM: dts: msm: remove qcom,power-always-on dt property
  ARM: dts: msm: Fix EP PCIe perst pinctrl settings on sdxlemur
  ARM: dts: msm: enable reg dump collection
  ARM: dts: qcom: Add ipq807x_attach property for IPQ807x host
  ARM: dts: qcom: Add device tree entry for sdx ipc driver
  bindings: arm: msm: Add documentation for sdx ipc driver
  ARM: dts: msm: qcom: Add pm7250b support for Blair-MTP-USBC platform
  ARM: dts: msm: Add dual NIC IPA support
  ARM: dts: msm: Pin config for AQR and Napa INTN_WOL
  ARM: dts: qcom: PCIe to Gen3 for NTN3 CPE Pine1x
  ARM: dts: msm: NTN3 De-emphasis values update CPE
  ARM: dts: msm: Enable SMMU S1 support for eMMC on sdxlemur
  ARM: dts: msm: Rename L1 disable property for blair
  ARM: dts: qcom: Add Support for QCN9000 for MTP CPE
  ARM: dts: qcom: Move all WLAN configs out of sdxlemur-mtp-cpe.dtsi
  ARM: dts: msm: Rename L1 disable property to align with driver
  ARM: dts: qcom: Update hvx and skin config rules for BLAIR
  ARM: dts: msm: Remove unused smps regulator
  ARM: dts: msm: Remove unused smps regulator
  ARM: dts: msm: add AW2016 LED device nodes for blair platforms
  ARM: dts: msm: change wdi3 holb timeout
  ARM: dts: msm: Skip BW vote for PM8008 used I2C SE node
  ARM: dts: msm: Add qos silver cores to device tree
  ARM: dts: msm: Add changes for blair USBC target
  ARM: dts: msm: Add AW2016 LED device nodes for Holi-m6125 platforms
  ARM: dts: msm: Add disable u1 quirk and u2 quirk for blair
  ARM: dts: msm: qcom: Update refgen node for blair-atp platform
  ARM: dts: msm: Restore SDCC registers once Resuming from CX/XO
  ARM: dts: msm: Add cx_misc register map for yupik GPU
  ARM: dts: msm: Add changes to support ATP on blair
  ARM: dts: msm: add tzpu_ctx dump entry
  ARM: dts: msm: Updating MTP-USBC platform dtb for blair target
  ARM: dts: msm: Enable display on Blair ATP platform
  ARM: dts: msm: Ignore SSR failure for wpss
  ARM: dts: msm: qcom: Fix proxy-supply for blair regulator nodes
  ARM: dts: msm: Align sdxlemur BT config with sdxprairie
  ARM: dts: msm: updating modem_tj mitigation for LAHAINA
  dt-bindings: leds: Add bindings for AW2016 LED device
  dt-bindings: Add awinic vendor name
  ARM: dts: msm: updated memory map v1 for blair
  ARM: dts: qcom: Add modem mitigation for bcl violation in lahaina
  ARM: dts: msm: Update USB2 core frequency for yupik
  ARM: dts: msm: Change cpu frequency for V2 hardware
  ARM: dts: msm: Enable display on Blair ATP platform
  ARM: dts: msm: Add pm-qos-latency dt node for sdxlemur
  ARM: dts: msm: Enable link recovery for config space access fail
  ARM: dts: msm: Disable Skin config rules for BLAIR
  ARM: dts: msm: disable ipa-uc-holb-monitor
  ARM: dts: msm: disable masking MSI interrupts at EP side
  ARM: dts: msm: Adding updated PHY tune parameters for blair
  dt-bindings: pcie: Notify client for config space access issues
  ARM: dts: msm: Add support of 608Mhz GPU FMAX for yupik
  ARM: dts: msm: enable LAN RX NAPI
  ARM: dts: msm: add ADC device instance for PMR735A on holi-pm6125
  dt-bindings: iio: qcom,spmi-vadc: Add SW-calibrated ADC bindings
  ARM: dts: msm: Enable cxipeak support for blair
  ARM: dts: msm: Add APPS_APM_STATUS register for blair
  ARM: dts: msm: Update dcc registers for blair
  ARM: dts: msm: Add disable L1 quirk in HS mode for blair
  ARM: dts: msm: Modify ss phy initialization sequence on sdxnightjar
  Revert "ARM: dts: msm: Set qcom,rmnet_in_use_tcm_mem with RMNET composition"
  ARM: dts: msm: Add device tree for M.2 USB mode on sdxlemur
  ARM: dts: qcom: enable cx ipeak lm separately for blair and holi-pm6125
  ARM: dts: msm: add ntn3 ipa pcie changes
  ARM: dts: msm: Mark PMIC QUPs as critical clock devices for BLAIR
  ARM: dts: msm: Add wdog bite IRQ for pil modem
  ARM: dts: msm: update clk tput threshold for IPA on Olympic
  ARM: dts: msm: Update mode threshold current of L6C of yupik
  ARM: dts: msm: Add support to sync charger/qg probe with vadc
  ARM: dts: msm: set need unvote flag 0
  ARM: dts: msm: Update BCL thermal mitigation config for HOLI
  ARM: dts: msm: rename sound card for QRD blair
  ARM: dts: msm: Add APPS_APM_STATUS register for blair
  ARM: dts: msm: Correct #address-cells property for PM6125
  ARM: dts: msm: Add FnR stats support flag for holi target
  ARM: dts: msm: Add disable L1 quirk in HS mode for sdxnightjar
  ARM: dts: msm: Enable QPIC display for sdxlemur
  ARM: dts: msm: Update spmi debugfs nodes for yupik with PM7250B
  Revert "ARM: dts: msm: Add UFS ICE HW controlled clock for yupik"
  ARM: dts: msm: Add interrupt mask offset for EUD for sdxlemur
  dt-bindings: Add optional EUD parameter for interrupt mask
  ARM: dts: msm: Add disable L1 quirk in HS mode for blair
  ARM: dts: msm: Update dcc registers for blair
  ARM: dts: msm: Add skin and mmw thermal config for YUPIK
  ARM: dts: msm: Include camera sensor dtsi for blair QRD
  ARM: dts: msm: Add support for mpm interrupts on blair
  ARM: dts: msm: Give Blair its own MPM pins mapping configuration
  ARM: dts: msm: Replace regulator value for vdd-pdphy-supply on blair
  ARM: dts: msm: correct l2_cache dump size on blair
  ARM: dts: msm: Add support for mpm interrupts on blair
  ARM: dts: msm: Add a new property for Blair touch
  ARM: dts: msm: Enable cxipeak support for BLAIR
  ARM: dts: msm: Disable NAP power feature for blair GPU
  Revert "ARM: dts: msm: Add video support for KODIAC-IOT target"
  ARM: dts: msm: Add QRTR MHI DEV device for sdxlemur
  dt-bindings: net: qrtr: Add MHI Device transport bindings
  ARM: dts: msm: Add device trees for sdxlemur M.2, Pine variants
  ARM: dts: msm: Replace regulator value for vdd-pdphy-supply on blair
  ARM: dts: msm: Add support for usb nodes on blair
  ARM: dts: msm: Add device trees for sdxlemur + IPQ8074
  ARM: dts: msm: Add nopmi support for holi-pm6125 and blair
  ARM: dts: msm: Add clkreq gpio for PCIe nodes for yupik
  ARM: dts: msm: Fix resource-name and id for holi-pm6125-regulator
  ARM: dts: msm: Updating ATP platform dtb for blair target
  ARM: dts: msm: correct l2_cache dump size on blair
  ARM: dts: msm: Set proper vddpx supply
  ARM: dts: msm: add ntn3/qps615 pci DT nodes for sdxlemur
  ARM: dts: qcom: Limit PCIe to Gen3 for oculink connects on sdxlemur
  ARM: dts: msm: Add camera device tree inclusions for Blair camera
  ARM: dts: msm: Include camera sensor dtsi for QRD Holi-pm6125
  ARM: dts: msm: Vote for S5A during BT operations
  ARM: dts: msm: Vote for S5A during wlan operations
  ARM: dts: msm: Add support for usb nodes on blair
  ARM: dts: msm: Include camera sensor dtsi for blair QRD
  bindings: input: qcom-hv-haptics: Add "qcom,pm5100-haptics"
  ARM: dts: msm: update ADC channels for holi-pm6125
  ARM: dts: msm: Update QG cutoff/empty thresholds for blair/holi-pm6125
  ARM: dts: msm: include display nodes for Blair qrd
  ARM: dts: msm: Add UFS regulators for qrd holi-pm6125
  ARM: dts: msm: Give Blair its own MPM pins mapping configuration
  ARM: dts: msm: disable mss cti on holi
  ARM: dts: msm: Remove unused static supply for holi-pm6125
  ARM: dts: msm: Add extcon phandle for usb0 on blair cdp
  ARM: dts: msm: Correct SPMI node name for holi-pm6125 ADC_TM
  ARM: dts: msm: Add extcon phandle for usb0 on blair cdp
  ARM: dts: msm: Remove unused static supply for holi-pm6125
  ARM: dts: msm: Include camera sensor dtsi for blair QRD
  ARM: dts: msm: change vdd supply for WSA
  ARM: dts: msm: Add touch for QRD Blair
  ARM: dts: msm: include display nodes for Blair qrd
  ARM: dts: msm: Add UFS regulators for qrd blair
  ARM: dts: msm: Add touch for QRD Holi-pm6125
  ARM: dts: msm: Add I2C NFC device node for holi pro QRD variant
  ARM: dts: msm: Add UFS regulators for qrd holi-pm6125
  ARM: dts: msm: include display nodes for pm6125 platform of Holi qrd target
  ARM: dts: msm: correct dump entry size
  ARM: dts: msm: increase dump entries size in blair
  ARM: dts: msm: Enable cpufreq cooling device for BLAIR
  ARM: dts: msm: Add camera device tree inclusions for Blair camera
  ARM: dts: msm: Updating platform dtb(s) for blair targetr
  ARM: dts: msm: Set proper wsa reset gpio
  ARM: dts: msm: Add support for usb nodes on blair
  ARM: dts: msm: Removing signal-aop from pils on Blair
  ARM: dts: msm: Update DLL values as per HSR for blair
  ARM: dts: msm: Disable TBU halting for pcie tbu on sdxlemur
  ARM: dts: msm: change vdd supply for WSA
  ARM: dts: msm: Set proper wsa reset gpio
  ARM: dts: msm: Add touch for QRD Blair
  ARM: dts: msm: Add UFS regulators for qrd blair
  ARM: dts: msm: Remove the audio ION CMA heap for sdxlemur
  ARM: dts: msm: Add a carveout heap for audio usecases on sdxlemur
  ARM: dts: msm: Add an audio ION device node for the audio carveout heap
  ARM: dts: msm: Update the memory map for 1 GB variants of sdxlemur
  ARM: dts: msm: Removing signal-aop from pils on Blair
  ARM: dts: msm: use dummy regulator for new QRD Holi
  ARM: dts: msm: Add touch for QRD Holi-pm6125
  ARM: dts: msm: Update DLL values as per HSR for blair
  ARM: dts: msm: correct dump entry size
  ARM: dts: msm: increase dump entries size in blair
  ARM: dts: msm: Enable cpufreq cooling device for BLAIR
  ARM: dts: qcom: enable cx ipeak common driver for holi-pm6125
  dt-bindings: Add victims_table bindings for cx_ipeak driver
  ARM: dts: msm: Updating platform dtb(s) for blair targetr
  ARM: dts: msm: Add I2C NFC device node for holi pro QRD variant
  ARM: dts: msm: add cpulist to compute mon governor in blair target
  ARM: dts: msm: include display nodes for pm6125 platform of Holi qrd target
  ARM: dts: msm: Update board-id for PM7250B
  ARM: dts: msm: Add DT support for nopmi on Blair target
  ARM: dts: msm: Add initial MTP-USBC platform device tree for Blair
  ARM: dts: msm: add PM7250B and SMB1394 to sdxlemur-mtp-mbb-emmc boards
  ARM: dts: msm: add remote debugger support
  ARM: dts: msm: add msm poweroff node on qcs405
  ARM: dts: msm: Enable modem subsystem
  ARM: dts: msm: Add BCL configuration for yupik IDP with PM7250B
  ARM: dts: msm: Enable BT for Scuba
  ARM: dts: msm: Add video support for KODIAC-IOT target
  ARM: dts: msm: Update min-access length for monaco IoT
  ARM: dts: msm: Include camera DTSi files for monaco
  ARM: dts: msm: Enable DP and NON DP in rename block
  ARM: dts: msm: Add audio definition for QRD Holi-pm6125
  ARM: dts: msm: Include pm5100 and pm8010 regulators for monaco
  ARM: dts: msm: Add apss dl cti0 for yupik
  ARM: dts: msm: Add apss dl cti0 for shima
  ARM: dts: msm: updated qseecom mem node
  ARM: dts: msm: Add support for Blair QRD platform
  ARM: dts: msm: Enable multiport USB for SA8195 LA GVM
  ARM: dts: msm: Update dpdm_supply for USB for  Monaco
  ARM: dts: msm: Add initial ION heaps for SA2150P
  ARM: dts: msm: Update UFS phy regulator peak current for blair
  ARM: dts: msm: Add aop_send_message device node interface for sdmshrike
  ARM: dts: msm: Enable IPA node for monaco target
  ARM: dts: msm: add display support for monaco IDP
  ARM: dts: msm: Add aop_send_message device node interface for SA6155
  ARM: dts: msm: Add aop_send_message device node interface for SA8155
  ARM: dts: qcom: enable gpu mitigation for TSENS and BCL for monaco
  ARM: dts: msm: Remove unused static supplies for holi-pm6125
  ARM: dts: msm: Fix regulator naming for pm8010
  ARM: dts: msm: Fix ldoa3 regulator for monaco
  ARM: dts: msm: add touch support of lcd panel for Blair target
  ARM: dts: msm: include display nodes for Blair target
  ARM: dts: msm: use dummy regulator for 3V eLDO supply of touch on Holi
  ARM: dts: msm: Set allowable min volt of L9B to 1.2V for Yupik
  ARM: dts: msm: Enable modem pa sensor config only for YUPIK QRD
  ARM: dts: qcom: Add thermal overlay devicetree support for holi-pm6125
  dt-bindings: kgsl: Add compatible property in qcom,gpu-model
  ARM: dts: msm: Add pin controls for camera GPIOs
  ARM: dts: msm: add RPM managed regulator devices for QCS405
  ARM: dts: msm: Add rpm-smd node for qcs405
  ARM: dts: msm: Add smb1394 support for holi-pm6125
  ARM: dts: qcom: Add flash pinctrl gpio for blair
  ARM: dts: msm: Update ADC support for PM6125
  ARM: dts: qcom: add ipc and codec cdev nodes
  ARM: dts: msm: Remove generic labels for regulators
  ARM: dts: msm: Update the LDO2/3A min-max voltages
  ARM: dts: msm: Disable EP initiated BW scaling on switch for sdxlemur
  ARM: dts: msm: Fix incorrect regulator label references
  ARM: dts: msm: Add cnss dtsi to cpe
  ARM: dts: msm: Set qcom,rmnet_in_use_tcm_mem with RMNET composition
  ARM: dts: qcom: enable pmic alarm sensor and BCL thermal zones for monaco
  ARM: dts: qcom: Remove duplicate thermal zone phandle for monaco
  dt-bindings: Add dt bindings for silent boot mode
  ARM: dts: qcom: Enable cx ipeak cooling device configuration for holi
  ARM: dts: qcom: add slate VA interface
  ARM: dts: msm: Add GPU support for monaco IoT
  ARM: dts: qcom: add audio dts source file for Monaco
  ARM: dts: msm: Add MSM PCIe bus driver device nodes for direwolf
  ARM: dts: qcom: update sdhc properties
  ARM: dts: msm: Disable modem region reserved on sa8155
  ARM: dts: msm: Add WDT node for SA2150P
  dt-bindings: Add snapshot of CX Ipeak cooling device devicetree binding
  ARM: dts: msm: Remove qcom,gpu-qdss-stm property for Shima GPU
  ARM: dts: msm: Add ion secure heap and secure buffer for quin-vm
  ARM: dts: msm: sensors glink channels
  ARM: dts: msm: Update ddr stats to support mbox for yupik
  ARM: dts: msm: Update ddr_stats to support mbox for lahaina
  dt-bindings: arm: ddr_stats: Add QMP mailbox as optional property
  ARM: dts: msm: change min voltage of touch_avdd fixed regulator
  dt-bindings: qpnp-smblite: Update smblite charger compatible string
  ARM: dts: msm: Add video dtsi in monaco target dtsi
  ARM: dts: msm: Add bus topology in Monaco Venus PIL
  ARM: dts: msm: Interconnect bus handling in video
  ARM: dts: msm: Add monaco video dtsi in target dtsi
  ARM: dts: msm: Correct syntax error and reorder dts variants for monaco
  ARM: dts: msm: add lxc overlay supoort on v1 board
  ARM: dts: msm: Add jtag_mm nodes for monaco
  ARM: dts: msm: updated monaco qupv3 dtsi
  ARM: dts: msm: Update base address for monaco
  dt-bindings: thermal: Add support for ibat CCM hardware to bcl driver
  ARM: dts: msm: Add thermal zones for pm5100 temp alarm
  ARM: dts: msm: Do not timeout waiting for M0
  dt-bindings: Add DT bindings for monaco
  ARM: dts: msm: Enable audio only for 1GB variants
  ARM: dts: msm: Add mproc related node support for qcs405
  dt-bindings: clock: Add support for QCS404 clock controllers
  ARM: dts: msm: Add ADC support for PM5100
  ARM: dts: msm: Add Mproc driver support for direwolf
  ARM: dts: msm: Add alloc-ranges in mem_dump_region node
  ARM: dts: qcom: keep all step wise rules before userspace rules for YUPIK
  ARM: dts: msm: Add support for BT in blair platform
  ARM: dts: qcom: enable tsens and thermal zone mitigations for monaco
  ARM: dts: qcom: Add flash pinctrl gpio for holi Pro
  ARM: dts: msm: Enable icnss node for blair
  ARM: dts: msm: Add eMMC platform support for Monaco variants
  ARM: dts: msm: Add regulator and supplies for holi-pm6125
  ARM: dts: msm: Update bluetooth regulator for holi-pm6125
  ARM: dts: msm: Add initial board files for QRD Holi-pm6125
  ARM: dts: msm: Add stubs pm8010 and Speaker boost regulators
  ARM: dts: msm: Add VOLUME UP Key configuration for Monaco
  ARM: dts: msm: Add QBG battery profile for Alium 3600 mAh battery
  ARM: dts: msm: Add icnss driver for monaco
  bindings: clock: Add support for DIREWOLF Display clock controllers
  ARM: dts: msm: Include PM5100 PMIC for Monaco
  ARM: dts: msm: Enable usb host for scuba
  ARM: dts: msm: Add USB nodes for Scuba
  ARM: dts: msm: add stub interconnect devices for Scuba
  ARM: dts: msm: Update SMMU Interconnect for scuba iot
  ARM: dts: msm: Update kgsl smmu clock for scuba
  ARM: dts: msm: Add eMMC, SD card support for SCUBA
  ARM: dts: msm: Add dt nodes for spi, i2c, uart for scuba
  ARM: dts: msm: enable bluetooth for direwolf vm
  ARM: dts: msm: Add initial device tree for SA2150P
  ARM: dts: qcom: Fix three issues in WLAN converged node
  ARM: dts: msm: Update clock handles for PCIE nodes
  ARM: dts: msm: Add USB dtsi nodes for monaco
  ARM: dts: msm: Include display nodes for yupik idp with PM7250B
  ARM: dts: msm: Add clock controller nodes for SCUBA
  ARM: dts: qcom: add audio device tree source files
  ARM: dts: msm: Add Superspeed PHY node on blair
  ARM: dts: msm: Add UFS support for blair platforms
  ARM: dts: msm: adjust S4C voltage
  ARM: dts: msm: Add dtsi security nodes for direwolf gvm
  ARM: dts: msm: Adding missing dump entries in blair
  bindings: clock: Add support for SCUBA clock controllers
  dt-bindings: interconnect: add interconnect bindings
  ARM: dts: msm: Fix compilation warnings for sa8155, sa8195 and sa6155
  ARM: dts: msm: Add USB regulators for holi-pm6125
  ARM: dts: msm: Update GPU revision for Yupik
  ARM: dts: qcom: Remove PMIC dt inclusion
  ARM: dts: msm: replace usb regulator values for BLAIR ATP platform
  ARM: dts: msm: Add support for yupik IDP with PM7250B
  ARM: dts: msm: Add device tree support for PM7250B
  ARM: dts: msm: Update thermal zone entries for holi-pm6125
  ARM: dts: msm: Add initial PMIC and regulator support for blair
  ARM: dts: msm: Add high speed PHY node on blair
  ARM: dts: msm: Add UFS regulators for holi-pm6125
  ARM: dts: msm: Add primary and secondary USB nodes on Direwolf
  ARM: dts: msm: Add support for QUPv3 dtsi
  ARM: dts: msm: Update the QMP UNIPHY init sequence for SM8150
  ARM: dts: msm: add MHI register space info for PCIe on SA6155
  ARM: dts: msm: add MHI register space info for PCIe on SA8195
  ARM: dts: msm: add MHI register space info for PCIe on SM8150
  ARM: dts: qcom: update mapping table for dcvvs nodes in blair target
  ARM: dts: msm: add wdi scaling exceptions
  ARM: dts: msm: Add GPU properties for Blair
  ARM: dts: msm: Move icnss driver to soc node
  ARM: dts: msm: Add modem mmw_skin mitigation config for HOLI
  ARM: dts: msm: Update silver core mitigation for YUPIK
  ARM: dts: msm: Add mproc node for slate
  ARM: dts: msm: Add correct LDO reference for NFC LDO voting
  ARM: dts: msm: Add initial platform device tree for blair QRD
  ARM: dts: msm: Enable Secure buffer for monaco
  ARM: dts: msm: Include camera sensor dtsi for holi pro
  ARM: dts: msm: Add UFS support for direwolf
  ARM: dts: msm: Add entry to configure modem tput ep
  ARM: dts: msm: include touch nodes for rm69299 panel on Holi target
  ARM: dts: msm: include display nodes for pm6125 platform of Holi target
  ARM: dts: msm: Add icnss regulator for holi-pm6125
  ARM: dts: msm: include camera devicetree for sa6155
  ARM: dts: msm: Signal aop change for PIL for BLAIR
  ARM: dts: msm: include coresight device tree file for monaco
  dt-bindings: pinctrl: qcom-pmic-gpio: add PM5100 bindings
  ARM: dts: msm: Disable two_pass_use_wfi quirk for yupik GPU
  dt-bindings: regulator: add cpr, mem-acc, spm regulator bindings
  dt-bindings: interconnect: add interconnect bindings for QCS405
  ARM: dts: msm: Add eMMC/SD card regulators for holi-pm6125
  ARM: dts: msm: Add regulator and PMIC support for holi-pm6125
  ARM: dts: msm: Add the APPS SMMU device for direwolf
  ARM: dts: qcom: Upadate base dts file for Monaco
  ARM: dts: msm: Add coresight device tree for monaco
  dt-bindings: usb: Document usage of new ANoc and SysNoc clocks
  ARM: dts: qcom: Add spi node for slatecom
  ARM: dts: msm: disable mss cti
  ARM: dts: msm: Add gpu-model property for shima gpu
  ARM: dts: msm: Enable Qseecom node for monaco
  ARM: dts: msm: Enable qsee drivers for monaco
  ARM: dts: msm: add more dts properties for 2nd ufs
  ARM: dts: msm: Add GPIO support for the PCIe RCs on the Direwolf platform
  ARM: dts: msm: Add PCIe clocks and regulators for the Direwolf VM
  ARM: dts: msm: Rename regulators file for holi and blair
  ARM: dts: msm: Remove RPMh macros from monaco-regulators
  ARM: dts: msm: Remove stub regulators from monaco rumi
  ARM: dts: msm: Add dcc registers lists for yupik
  ARM: dts: msm: add cnss node for sa6155p-vm
  ARM: dts: msm: Change renamed partition names for Direwolf guest
  ARM: dts: msm: Add initial platform device tree for blair
  ARM: dts: msm: Add vk-device-id property
  ARM: dts: msm: Add wakeup interrupt controller for Monaco
  ARM: dts: msm: Add system_pm_rpm node for Monaco
  ARM: dts: msm: Add LPM device nodes and stats for Monaco
  ARM: dts: msm: Add device tree variants for Monaco
  ARM: dts: msm: Update PHY sequence for sdxlemur
  ARM: dts: msm: Update GPU revision for Shima
  ARM: dts: qcom: Add HS-I2S device tree support on SA6155
  dt-bindings: thermal: Snapshot of lmh cpu VDD driver document from msm-4.19
  ARM: dts: qcom: Add qcom in SiRF GNSS driver
  ARM: dts: msm: Add rmtfs_sharedmem support for monaco
  ARM: dts: msm: bindings: include camera devicetree for sa6155
  dt-bindings: add bindings for gnss_sirf
  ARM: dts: msm: Enable cnss on 6155 guest
  ARM: dts: msm: Add ACD control register values for Yupik GPU
  ARM: dts: msm: Update CNSS node for BT GPIO config
  ARM: dts: msm: update ab/ib votes for IPA on Olympic
  ARM: dts: msm: Add thermal configuration for sdxlemur
  dt-bindings: qcom: Add boolean flag to enable concurrency mode
  ARM: dts: qcom: Add HS-I2S device tree support on SA8195
  ARM: dts: msm: Add video dtsi in scuba target dtsi
  ARM: dts: msm: Add bus topology in Scuba Venus PIL
  ARM: dts: msm: Add scuba video dtsi in target dtsi
  bindings: Use list of PCIe RC ports for WLAN device
  ARM: dts: msm: Add GPUCC clock node and GDSCs for MONACO
  ARM: dts: msm: Update clock frequenices for PCIe 2nd instance
  ARM: dts: msm: Enable LLCC support in IOSS for sdxlemur
  ARM: dts: qcom: Add wlan node for sa6155
  dt-bindings: iio: qcom,spmi-vadc: Add PMIC5 GEN3 ADC bindings
  Revert "ARM: dts: msm: Disable NPU DCVS support on SM8150"
  Revert "ARM: dts: msm: Disable NPU DCVS support on SA8195"
  ARM: dts: msm: Enlarge the minidump cma area
  ARM: dts: msm: Add ION support for Direwolf
  ARM: dts: msm: Add LLCC device nodes for Direwolf
  ARM: dts: msm: Add LLCC PMU device nodes on Direwolf
  ARM: dts: msm: Add devfreq support nodes for Direwolf
  ARM: dts: msm: Add support for clock controllers for BLAIR
  bindings: clock: Add debugcc bindings for BLAIR
  ARM: dts: msm: Update CPUFREQ-HW nodes for Blair
  ARM: dts: msm: Change the shmbridge default size to 1M
  ARM: dts: msm: setting clk is provided by SOC
  dt-bindings: batterydata: Add bindings for properties used by QBG
  bindings: spmi: spmi-pmic-arb: Add description for "qcom,mid"
  dt-bindings: thermal: Add new QMI sensors to the supported list
  ARM: dts: msm: Enable CPU cooling device for sdxlemur
  ARM: dts: msm: Add extcon node for sdxlemur-atp
  ARM: dts: msm: Add PM7250B to sdxlemur-atp
  ARM: dts: msm: Include sdxlemur-mtp dt in sdxlemur-atp
  ARM: dts: msm: bypass IPA eth shared-cb
  ARM: dts: msm: update interconnect devices for Monaco
  ARM: dts: qcom: add audio device tree source files
  ARM: dts: msm: Enable L3 interconnect driver for direwolf
  ARM: dts: msm: Add ADC thermistors for sdxnightjar
  ARM: dts: msm: add interconnect devices for direwolf
  ARM: dts: msm: Add wakeup support for SDIO
  ARM: dts: msm: Fix DDR OPP table entries
  ARM: dts: msm: Indentation issue for qcom,scm on direwolf vm
  ARM: dts: msm: Add initial device tree for SCUBA
  ARM: dts: msm: Enable Virtual SSR for the Direwolf VM
  ARM: dts: msm: add SPMI PMIC arbiter and PMIC devices for direwolf
  dt-bindings: interconnect: add interconnect bindings for direwolf l3
  ARM: dts: msm: include sdmshrike-vm-lv-display.dtsi
  ARM: dts: msm: add bt power node for sa6155
  ARM: dts: msm: Set R8125B Rx ring size on sdxlemur
  ARM: dts: msm: Reduce USB IOVA address size by size of LLCC TCM memory
  ARM: dts: msm: Add entry to t_power_on scale and value on sdxlemur
  ARM: dts: msm: Remove SDPM and policy-engine support for YUPIK
  ARM: dts: msm: Correcting watchdog node in blair-rumi.dtsi
  dt-bindings: Add DT bindings for scuba
  ARM: dts: msm: delete rename-blk on sa8195 LXC VM
  ARM: dts: msm: Update Ibat threshold and BCL thermal config for YUPIK
  ARM: dts: msm: Add skin, modem and junction thermal config for YUPIK
  ARM: dts: msm: Enable QCPE on direwolf vm
  ARM: dts: msm: Use svs bus voting with USB on sdxlemur
  ARM: dts: msm: Remove duplicate dt node for qupv3 from sm8150
  ARM: dts: msm: Fix compilation warnings for auto GVM device tree
  ARM: dts: msm: Add device tree for sdxlemur ATP variant
  bindings: power: supply: Add documentation for QTI Battery Gauge
  dt-bindings: Add devicetree bindings to devicetree project
  ARM: dts: msm: enable SiRF GNSS Driver and hsuart1
  Revert "ARM: dts: msm: Add LA specific TVM flag in respective SPI node"
  ARM: dts: msm: Add DISPCC/DEBUGCC clock node for MONACO
  ARM: dts: msm: Add MX property for PCIe on sdxlemur
  ARM: dts: msm: Update load factor for PCIe rail on sdxlemur
  ARM: dts: msm: Disable icnss node for blair
  ARM: dts: msm: mv quat/quin slpi pinctrl to SLPI devicetree file
  ARM: dts: msm: Add device tree for sdxlemur eMMC 512 MB variant
  ARM: dts: msm: Add gpu-model property for yupik gpu
  ARM: dts: msm: Adding updated PHY tune parameters for Yupik
  ARM: dts: msm: Add USB nodes for Blair
  ARM: dts: msm: Add support for GPU models properties
  ARM: dts: msm: Add shared memory driver support
  ARM: dts: msm: add MX entries for PCIe EP on sdxlemur
  ARM: dts: msm: Add QUPv3 functionality for the Direwolf VMs
  ARM: dts: msm: Add aopcc for direwolf
  ARM: dts: msm: Add cpufreq HW device node for direwolf
  ARM: dts: msm: Add gcc, rpmhcc and gdsc nodes for direwolf
  bindings: update documentation for custom-bridge-size
  ARM: dts: qcom: Remove unused mem reservation for wlan
  ARM: dts: qcom: Update fan cooling thermal config for HHG
  ARM: dts: msm: Remove CNSS WLAN CMA region for sdxlemur-512M variants
  ARM: dts: msm: Add SDPM domain indexes for YUPIK
  bindings: cpufreq-hw: Add support for SDPM CX/MX offset
  dt-bindings: leds-qpnp-flash-v2: Add support to control ramp time
  ARM: dts: qcom: Add qti-can device tree node
  bindings: Add device-tree bindings for slate_events_bridge driver
  ARM: dts: msm: disable rpm etm
  ARM: dts: msm: change the data delay to 1 for direwolf GVM audio
  ARM: dts: msm: update gold L3 memlat mapping for yupik target
  ARM: dts: msm: Add spmi device tree node for sa8195
  ARM: dts: msm: bypass S1 dma mappings in Linux guest
  ARM: dts: msm: add USB0 for SA8195 LXC VM
  ARM: dts: msm: Add qcom_gadget node for sdxlemur
  ARM: dts: msm: Adding new DT entries for ETH bridging
  ARM: dts: msm: Add VBUS supply for USB2 port for Yupik IOT IDP
  ARM: dts: msm: Update the venus and vcodec gdsc for monaco
  ARM: dts: msm: STMMAC changes for SA6155
  ARM: dts: msm: Add switch control GPIO for WLAN
  ARM: dts: msm: Add SPI to support PCIe SNPS IRQ 1-7 for sdxlemur
  ARM: dts: msm: Add support for USB on Direwolf GVM
  ARM: dts: msm: Enable USB2 functionality for yupik IOT IDP
  Revert "ARM: dts: msm: Use PCIe_MSI for Shima"
  ARM: dts: qcom: Enable CPU frequency cooling device for YUPIK
  dt-bindings: Add opp table for ahb device
  ARM: dts: msm: Add the rpmcc support for monaco
  ARM: dts: msm: Enable hgsl support on direwolf
  ARM: dts: qcom: Add modem TSENS thermal zone mitigations for HOLI
  ARM: dts: qcom: Add HS-I2S device tree support on SA8155
  ARM: dts: msm: Add direwolf QUPv3 spi, i2c and console nodes
  ARM: dts: msm: include direwolf-vm-lv-display.dtsi
  ARM: dts: msm: Support new TDM interfaces for Automotive
  ARM: dts: msm: fix rtc entries
  ARM: dts: msm: enable disable-alarm-wakeup for rtc
  dt-bindings: qpnp-lcdb-regulator: Add support for some LCDB DT properties
  ARM: dts: msm: Add eMMC card support for monaco
  ARM: dts: msm: Add shared memory driver support
  ARM: dts: msm: Add dtsi changes for PCIe1 enablement for yupik
  ARM: dts: msm: Reduce cma region
  ARM: dts: msm: SA8155 EAVB fix
  ARM: dts: msm: SA6155 EAVB fix
  ARM: dts: msm: Enable GPIO function of GPIO171
  ARM: dts: msm: STMMAC changes for SA8195
  ARM: dts: msm: remove wlan section of mem_dump
  ARM: dts: msm: remove mem_dump region
  ARM: dts: msm: Add common CMA region for sdxnightjar
  ARM: dts: msm: Add base device tree for direwolf LA guest
  ARM: dts: msm: Add multi queue support
  ARM: dts: msm: Add cpufreq-hw clock node for MONACO
  ARM: dts: msm: multi-card for Gen3 platform lxc dtbo
  ARM: dts: msm: add audio gvm dts for auto direwolf platform
  ARM: dts: msm: Add DT entry for wrapper pm support
  ARM: dts: msm: set dma mapping mode to atomic
  ARM: dts: msm: Add MDM flag for Audio memory regions
  ARM: dts: msm: STMMAC changes for SA8155
  ARM: dts: msm: Add support for USB secondary clocks for YUPIK IOT
  ARM: dts: msm: Add hwrng nodes for sa8155 and sa8195 VM
  ARM: dts: msm: Enable L1SS sleep for p-v2.1
  ARM: dts: msm: Update PCIe0 PHY settings to v1.00 for p v2.1
  ARM: dts: msm: Correct the soc dts info for HHG HSP Pro platform
  ARM: dts: msm: add 2nd UFS for Quin SA8195 LXC VM
  ARM: dts: msm: enable dual wlan for Quin SA8195 VM LXC
  ARM: dts: msm: Move display include to end of quin-vm-common
  ARM: dts: msm: Disable IPA for yupik iot qcs variants
  ARM: dts: msm: Add initial device tree for direwolf virtual machine
  ARM: dts: msm: correct modem etm path
  ARM: dts: msm: enable mem_dump for Linux guest
  ARM: dts: msm: Add child node entry for CPE NTN3 i2c client on sdxlemur
  ARM: dts: msm: Add child node entry for MBB NTN3 i2c client on sdxlemur
  ARM: dts: msm: update quat tdm multilane config on auto VMs
  ARM: dts: msm: Add bindings for llcc tcm
  ARM: dts: qcom: Add modem TSENS thermal zone mitigations for SHIMA
  ARM: dts: msm: Add support for GCC for BLAIR
  ARM: dts: msm: Disable NPU DCVS support on SA8195
  ARM: dts: msm: Removed pil-scm-pas for sdxnightjar
  ARM: dts: msm: Modify BDF to SID mapping for MBB on sdxlemur
  ARM: dts: msm: Have PCIe RC control NTN3 and its ETH power for sdxlemur
  ARM: dts: msm: Filter NTN3 downstream BDF for sdxlemur
  dt-bindings: arm: msm: Add child node entry for NTN3 i2c client
  dt-bindings: arm: msm: add support for BDF filtering
  dt-bindings: clock: Add support for BLAIR clock controllers
  ARM: dts: qcom: remove audio heap allocation for sdxnightjar
  ARM: dts: msm: Add cpuidle states and LPM stats devices for direwolf
  ARM: dts: msm: update QUPs for sa8195 virtual machine
  Revert "ARM: dts: qcom: Enable the second UFS instance"
  ARM: dts: msm: Add Bluetooth device tree for SA6155VM
  ARM: dts: msm: Fix GPIO pin name
  ARM: dts: msm: Avoid xbl_aop_mem overlay with aop_cmd_db
  ARM: dts: msm: add gpio cells property for auto sa*155 platform
  ARM: dts: msm: Add fixed regulators for select sdxlemur boards
  bindings: clock: Add support for direwolf clock controllers
  ARM: dts: msm: reduce the fastmap memory
  ARM: dts: msm: Add spmi device tree node for sa6155p
  ARM: dts: msm: Reduce reserved size of modem for sdxnightjar
  ARM: dts: msm: Enable uefi_log memory for SA8155
  ARM: dts: msm: Enable rename_blk device for LXC guest
  ARM: dts: msm: Avoid xbl_aop_mem overlay with aop_cmd_db
  ARM: dts: qcom: add audio device tree source files
  ARM: dts: msm: Add capacity and DPC properties for Blair
  bindings: mproc: Add support for glink-slatecom strings
  ARM: dts: msm: Update skin and modem junction thermal config for YUPIK
  ARM: dts: msm: Correct interrupt specification for RTC
  ARM: dts: qcom: add pinctrl for audio internal mclk2 on sa6155 platform
  ARM: dts: msm: Correct wlan_vregs config name
  ARM: dts: msm: update smmu ipa iova on sa8155 vm
  ARM: dts: msm: enable smmu s1 for wlan on sa8155 vm
  ARM: dts: msm: configure iommu for pci wlan
  ARM: dts: qcom: Adjust configs in wlan node for SA8155 VM
  ARM: dts: msm: Add sdhc_2 for SA6155P Quin virtual machine
  ARM: dts: msm: Add interconnect data for USB on sdxnightjar
  ARM: dts: qcom: Move cnss_wlan_mem to sdxlemur-cnss.dtsi
  ARM: dts: msm: Add multiport USB support for SA8195 autogvm
  ARM: dts: msm: Change drive strength for swr tx to 2MA for yupik
  ARM: dts: msm: Add pm8xxx rtc device for monaco
  dt-bindings: rtc: rtc-pm8xxx: Add binding documentation for pm5100 rtc
  ARM: dts: msm: Add qmp aop voting support for direwolf
  ARM: dts: msm: Disable NPU DCVS support on SM8150
  ARM: dts: msm: Add trusted touch entries on yupik qrd
  ARM: dts: msm:  Add focaltech spi touch node in yupik qrd svm
  ARM: dts: msm: Fix IPA doorbell address for sdxlemur
  dt-bindings: interconnect: add interconnect bindings for direwolf
  ARM: dts: msm: Update USB IOVA start address on sdxlemur
  ARM: dts: msm: Add LA specific TVM flag in respective SPI node
  ARM: dts: msm: Update 0.9 vreg property for PCIe on sdxnightjar
  ARM: dts: msm: Add iio support for pmi632
  ARM: dts: msm: Add RPMh controlled PMIC regulators for direwolf
  ARM: dts: msm: Remove disable shmbridge property sa8195 GVM
  ARM: dts: msm: Add bindings for cpufreq
  ARM: dts: msm: Fix phandle lookup failures for apsscc on sdxlemur
  ARM: dts: msm: Add spmi device tree node
  ARM: dts: msm: Update correct masters for sdxnightjar
  ARM: dts: qcom: Enable the second UFS instance
  ARM: dts: msm: Remove PCIE clock from YUPIK IOT QRD
  ARM: dts: msm: Fix compilation errors for monaco
  ARM: dts: msm: Enable uefi_log memory for SA6155
  ARM: dts: msm: Add 128k and 265k pools for Lahaina
  ARM: dts: msm: Enable pil and dload support for Monaco
  dt-bindings: backlight: Add support to configure slew ramp time
  dt-bindings: backlight: Add support for exponential dimming
  ARM: dts: msm: Enable rpm standalone mode for blair
  ARM: dts: msm: Add mpm as gpio wakeup parent for sdxnightjar
  ARM: dts: msm: Enable uefi_log memory for sdmshrike
  ARM: dts: msm: Add set_ddr_capped_freq device node interface for SA8195
  ARM: dts: qcom: Update CPU and GPU mitigation rules on Lahaina HHG
  dt-bindings: spi-msm-geni: Add flag for SPI responder MISO-MOSI connection
  ARM: dts: msm: Add PDC interrupt controller device for direwolf
  ARM: dts: msm: Add RSC devices for direwolf
  ARM: dts: msm: Add SPS node for sdmshrike
  ARM: dts: qcom: Enable thermal zones and cooling devices for sa6155
  ARM: dts: qcom: update pmic alarm thermal zone mitigation for sa8155/sa8195
  ARM: dts: qcom: Enable thermal zones and cooling devices for sa8195
  ARM: dts: msm: Add IPA dtsi configuration for SA8195
  dt-bindings: arm: msm: devicetree documentation for PCIe EDMA
  ARM: dts: msm: Update SPMI PMIC ARB IRQ for sdxnightjar
  ARM: dts: msm: Add new dts files for 512MB support for sdxnightjar
  ARM: dts: msm: disable super speed phy of USB1 on Lahaina HHG
  ARM: dts: msm: Enable two_pass_use_wfi quirk for yupik GPU
  ARM: dts: msm: Update WLED support for yupik
  ARM: dts: msm: Adding device tree node for Blair pinctrl
  dt-bindings: Adding pinctrl devicetree binding for Blair
  ARM: dts: msm: Add initial device tree for Blair
  ARM: dts: msm: Enable CVP SMMU fault tolerance and Stall disable
  ARM: dts: msm: Add support for mpm interrupts on sdxnightjar
  ARM: dts: msm: Add the LPM and mpm node
  ARM: dts: msm: Add set_ddr_capped_freq device node interface for SA6155
  ARM: dts: msm: Add rpm-smd node for Monaco
  bindings: arm: msm: Added documentation for ipc spinlock
  dt-bindings: Update soc sleep stats to read legacy device data
  ARM: dts: msm: Add memshare for yupik
  ARM: dts: msm: Increase voltage for S11B and S1C
  ARM: dts: qcom: remove audio drivers not used for sdxnightjar
  ARM: dts: msm: Add wlan device tree for SA8155 VM
  ARM: dts: qcom: Add qti-can device tree node for sa8155
  ARM: dts: qcom: Add virtual ptp for sa8155 vm
  ARM: dts: msm: spcom: add vreg_sp and gpio_sp
  ARM: dts: msm: Add CX and MX SDPM configuration for YUPIK
  ARM: dts: qcom: Enable thermal zones and cooling devices for sa8155
  ARM: dts: msm: Add bluetooth power node for sa8155 virtual machine
  ARM: dts: msm: Enable IOMMU Geometry for WLAN
  ARM: dts: msm: Superset common regulators votes change for Lahaina
  ARM: dts: msm: Qseecom_ta_region removed from CMA
  ARM: dts: msm: Increase the S11B/S2E max voltage for Lahaina
  ARM: dts: msm: Add Bluetooth power node for SA8195 VM
  ARM: dts: msm: Add wlan device tree for SA8195 VM
  dt-bindings: ptp: Add virtual ptp memory entry
  ARM: dts: msm: add wlan converged node for SA81x5
  bindings: can: Add device-tree bindings for qti-can driver
  ARM: dts: msm:Reduce CMA region size
  ARM: dts: msm: Remove pwr_evt_irq for SA6155 and SA8155 USB3 cores
  ARM: dts: msm: STMMAC crash fix
  ARM: dts: msm: Add set_ddr_capped_freq device node interface for SA8155
  ARM: dts: msm: Adding support to send messages to AOP using QMP transport
  bindings: arm: msm: Add documentation for spm-v2
  ARM: dts: msm: Add Wakeup interrupt controller for sdxnightjar
  ARM: dts: msm: Enable PCIe0 nodes only for iot variant
  ARM: dts: msm: Add pil scm pass node
  ARM: dts: msm: Specify the irq type  and trigger level
  ARM: dts: msm: Add IPA device configuration for SA8155
  ARM: dts: msm: Add version 1 of the memory map for sdxlemur CPE
  ARM: dts: msm: update PCIe LTR value to 150us for sdxlemur
  ARM: dts: msm: Add aux clock property for PCIe EP on sdxlemur
  ARM: dts: msm: Add SPS node for sm8150
  ARM: dts: msm: Add SPS node for sa6155
  ARM: dts: msm: Add multiport USB support for SA8195
  ARM: dts: msm: Disable SSPHY autosuspend for Gen3 Auto platforms
  ARM: dts: msm: Correct the audio ion node heap type
  ARM: dts: msm: Add IPCC node for Direwolf
  ARM: dts: msm: Workaround till all IPA changes are merged
  ARM: dts: msm: Add qos-cores for fastrpc
  ARM: dts: msm: Add missing CPUSS dump nodes to SDMSHRIKE
  ARM: dts: msm: Add the iommu property for SSC QUP
  ARM: dts: msm: Fix cache dump sizes for SM8150
  ARM: dts: msm: Add veth ipa documentation for device node
  ARM: dts: msm: Add interconnect aggregation noc
  ARM: dts: msm: Add pshold dt node for Direwolf
  ARM: dts: msm: Add WDT node for Direwolf
  ARM: dts: msm: Add device-tree entry for IMEM for Direwolf SoC
  ARM: dts: msm: Add pinctrl node for TLMM on Direwolf SoC
  ARM: dts: msm: Populate reserved memory regions for Direwolf
  ARM: dts: msm: Add initial device tree for Direwolf
  ARM: dts: msm: Enable HMP for SA8195 and SA8155 VM
  ARM: dts: msm: Reduce the CMA region sizes for sdxlemur
  ARM: dts: msm: Add camera device tree inclusions for lahaina hhg
  ARM: dts: qcom: enable modem mitigations for bcl thermal zones for yupik
  ARM: dts: qcom: keep all step wise rules before userspace rules for lahaina
  ARM: dts: msm: Add hgsl support in  6155
  ARM: dts: msm: Add UFS ICE HW Node for SA8195 and SM8150
  dt-bindings: arm: msm: Add UFS ICE HW Node for SA8195 and SM8150
  ARM: dts: msm: Add power reset and watchdog nodes for sa8155 quin vm
  ARM: dts: msm: Add the iommu property on SA8155
  ARM: dts: qcom: vm: Add device nodes for second AFE rx and proxy tx devices
  ARM: dts: msm: add fixed-regulator to supply USB2 VBUS on Lahaina HHG
  ARM: dts: msm: Add cnss devicetree node for Yupik IoT
  ARM: dts: msm: Increase max voltage range for S1B
  ARM: dts: msm: Remove interconnect aggregation noc binding
  ARM: dts: msm: Add support for YUPIK LTE platform
  ARM: dts: msm: Change board-id for sa8195 lxc gvm
  ARM: dts: msm: Enable rename_blk device for Linux guest
  ARM: dts: msm: Add qfprom for sa6155
  ARM: dts: msm: include quin-vm-display.dtsi
  ARM: dts: msm: Add support to disable PDC wakeup for gpios for lahaina
  ARM: dts: msm: Add RPM SMD controlled PMIC regulators for Monaco
  ARM: dts: msm: correct dcc offset on sdxlemur
  ARM: dts: msm: update charger ADC channels for yupik IDP
  dt-bindings: Add device-tree bindings for virtual minidump driver
  ARM: dts: msm: Add changes for PCIe0 RC enablement for yupik
  ARM: dts: msm: Add support for new subtype id for yupik-iot
  ARM: dts: msm: disable tpdm sdcc on sdxlemur
  ARM: dts: msm: include audio dt files for sa6155 auto platforms
  ARM: dts: msm: Use separate property for multiple WLAN support
  ARM: dts: msm: include audio dt files for sa8195-vm auto platforms
  ARM: dts: msm: include audio dt files for sa8155-vm auto platforms
  ARM: dts: msm: include audio dt files for sa6155p-vm auto platforms
  ARM: dts: qcom: update scaling ratios for SMB_ICHG and SMB_IIN channels
  ARM: dts: msm: Disable uC hold monitor
  ARM: dts: msm: add se10 spi alias for sa6155 auto platform
  dt-bindings: msm: Add compatbile strings for direwolf
  ARM: dts: msm: Enable SMMU S1 support for eMMC on Yupik
  ARM: dts: msm: Add l3 endpoints and pwrlevels for yupik gpu
  ARM: dts: msm: Enable subsystem sleep stats driver for holi
  bindings: arm: msm: Add documentation for subsystem sleep_stats_driver
  dt-bindings: leds: qcom-clk: Add qcom,default-clk-trigger property
  ARM: dts: msm: include sa6155 display devicetree
  ARM: dts: msm: Removing appsbl-qseecom-support
  ARM: dts: msm: enable scmi plh protocol
  ARM: dts: msm: Add DPC property for SM6150
  ARM: dts: msm: Add DPC property for SA8195
  ARM: dts: msm: Add DPC property for SM8150
  ARM: dts: msm: add bt power node for sa81x5
  ARM: dts: msm: STMMAC changes for SA6155
  ARM: dts: msm: STMMAC changes for SA8155 LV
  ARM: dts: msm: STMMAC changes for SA8195
  ARM: dts: msm: Add secure buffer device for sdxnightjar
  ARM: dts: msm: Enable rpmh_master_stats to read master stats for holi
  dt-bindings: msm: rpmh-master-stats: Update reg as optional property
  ARM: dts: msm: set qupv3 se15 i2c rate to 100khz
  ARM: dts: msm: Enable the PCIE GDSC for YUPIK IOT
  ARM: dts: msm: Add IPA device configuration for SA8195
  ARM: dts: msm: Add base DT for smb1390 nodes
  ARM: dts: msm: use se22 spi alias instead of se2
  ARM: dts: msm: Base device tree of SA6155 GVM
  ARM: dts: msm: STMMAC Add doc for EMAC node
  ARM: dts: msm: STMMAC binding
  ARM: dts: msm: Add virtual spmi device tree node for sa8155
  ARM: dts: msm: Add NPU-DDR devfreq nodes to SA8195
  ARM: dts: msm: Add NPU-DDR devfreq nodes to SA8155
  ARM: dts: qcom: Enable TSENS and thermal zone changes for sdxnightjar
  ARM: dts: msm: Add IOSS config for Realtek R8125
  ARM: dts: msm: Add NPU device tree for sa8155/sa8195
  ARM: dts: msm: Add qcom,no-accumulative-counter property for cpufreq
  ARM: dts: msm: Add qseecom node for sa8195 GVM
  ARM: dts: msm: Enlarge the minidump cma area for SM8150
  ARM: dts: msm: Add DT snapshots for pmi632 and pm6125
  ARM: dts: msm: Enable qcom,power-always-on for GPU SMMUs on GKI targets
  ARM: dts: msm: Remove PCIE clocks from protected list for YUPIK IOT
  ARM: dts: qcom: thermal zones definition for thermistors on Lahaina HHG
  ARM: dts: msm: add pci DT nodes for PCIe switch for sdxlemur CPE
  ARM: dts: msm: expand iommu-map to support PCIe switch on sdxlemur CPE
  ARM: dts: msm: Modify irq type for qcedev,qcrypto
  ARM: dts: msm: Make sdhc aliases start from 0
  ARM: dts: msm: Add clock for SLPI pinctrl for SM8150
  ARM: dts: msm: add PCIe AUX clk freq for sa6155, sa8155, sa8195
  ARM: dts: msm: Add mpm2 sleep counter for sm8150
  ARM: dts: msm: Add PCIE clocks to protected list for YUPIK
  ARM: dts: msm: Add firmware support for SA8195
  ARM: dts: msm: Add firmware support for SM8150
  ARM: dts: msm: Add device nodes for FastRPC and CDSP Loader for SM6150
  ARM: dts: msm: Add device nodes for FastRPC and CDSP Loader for SA8195
  ARM: dts: msm: Add ADSP remoteheap vmlist for SA8155
  ARM: dts: msm: Enable qseecom on sdxnightjar
  ARM: dts: msm: Add scm node for msmsteppe
  ARM: dts: msm: Enable touch support on lahaina MTP 2.1
  ARM: dts: msm: add panel in ECM device for yupik QRD platform
  ARM: dts: msm: Add firmware support for SA6150
  ARM: dts: msm: Disable SDCC TPDMs on yupik
  ARM: dts: qcom: disable thermal zone gpu-skin-avg-step on Lahaina HHG
  ARM: dts: msm: Update S1B and S8B min voltages on yupik
  ARM: dts: msm: Add AQC IPA offload configs
  ARM: dts: msm: Add virtual subsystem notification nodes for SA8155 VM
  ARM: dts: msm: Add qcom,usb-charger dt prop on sdxlemur
  ARM: dts: msm: Enable IOSS v2 for sdxlemur
  ARM: dts: msm: Update USB properties for SA8155 GVM
  ARM: dts: msm: Update irq type for rtc and usb-id irq
  ARM: dts: msm: updated memory map v5 for holi
  ARM: dts: msm: Add proxy vote on display regulators on yupik
  ARM: dts: msm: Add ION support for SM6150
  ARM: dts: msm: Update MCLK rate
  ARM: dts: msm: Add initial device tree for yupik-iot
  ARM: dts: msm: Add IOSS v2 driver bindings
  ARM: dts: msm: Add support for kgsl driver on SA6155
  dt-bindings: arm: msm: add mhi registers entry for PCIe RC
  dt-bindings: arm: msm: remove deprecated io and bar entries for PCIe
  ARM: dts: msm: add MHI register space info for PCIe on sdxlemur
  ARM: dts: msm: Add RDPM register map for yupik GPU
  ARM: dts: msm: Add Pmesg Reserved Memory for Yupik
  ARM: dts: msm: Add qseecom node for sa8155 gvm
  ARM: dts: msm: Correct parent regulator for sdxlemur VDD_CX_LEVEL_AO
  ARM: dts: msm: Add DMIC0 support
  ARM: dts: msm: Add dt node for msm-poweroff on SM6150
  ARM: dts: msm: Add secure_buffer and qcom,scm device on SM6150
  ARM: dts: msm: Add mem-dump and CPU dump nodes to SM6150
  ARM: dts: msm: Add core-hang detect nodes to SM6150
  ARM: dts: msm: Add device node for llcc node on SM6150
  ARM: dts: msm: Add PMU device nodes to SM6150
  ARM: dts: msm: Add DCVS device nodes to SM6150
  ARM: dts: msm: Add device node for watchdog in SM6150
  ARM: dts: qcom: Add device nodes for second AFE rx and proxy tx devices
  ARM: dts: msm: include audio dt files for sax155 auto platforms
  ARM: dts: msm: enable IPA-AQC\RTL CB sharing
  ARM: dts: msm: Add pcie node for Realtek r8125 driver
  ARM: dts: msm: Remove the handles for PCIE clocks for Yupik
  ARM: dts: msm: Add vidc node for SA6155
  ARM: dts: msm: Update NSP and skin sensor thermal config for YUPIK
  ARM: dts: qcom: Update UBWC version to 3 for yupik gpu
  ARM: dts: msm: Enable qseecom on sdxlemur
  ARM: dts: msm: Enable qrng on sdxlemur
  ARM: dts: msm: Update noc reg sizes for sdmshrike
  ARM: dts: msm: Add AQC to ipa_eth_group1
  ARM: dts: msm: Add device tree node for GP2 clock driven led
  dt-bindings: add documentation for leds-qcom-clk
  ARM: dts: msm: Add ipa_eth_group1
  ARM: dts: msm: Add Buses,PCIe,USB and storage devices to SM6150
  ARM: dts: msm: Enable multiple WLAN drivers support for Lahaina
  ARM: dts: msm: expand iommu-map to support PCIe switch on sdxlemur
  ARM: dts: msm: Add audio nodes for sdxnightjar
  ARM: dts: msm: Add cdsp rpmsg entry in yupik
  ARM: dts: msm: Add dtsi entry for ssg hlos drivers
  ARM: dts: msm: Add dtsi entry for spss_utils, spcom drivers
  ARM: dts: msm: Add dtsi entry for spss_utils, spcom drivers
  ARM: dts: msm: Early mount of vendor partition
  ARM: dts: msm: Fix IPA doorbell address for sdxlemur
  ARM: dts: msm: Add new soc-id for sdxlemur
  ARM: dts: msm: Enable smcinvoke and shmbridge on yupik
  ARM: dts: msm: Add slpi pinctrl to SM6150
  ARM: dts: msm: Enhanced flow control support to sdxlemur target
  ARM: dts: msm: Correct syntax error
  ARM: dts: msm: Add PMUV3 node for monaco
  ARM: dts: msm: add touch support for more panels on qrd yupik
  ARM: dts: msm: include audio dt files for sa8195
  bindings: update documentation for support-legacy_smc
  ARM: dts: msm: Remove "msr-fix-req" label from some TPDMs
  ARM: dts: msm: Add PM8008 GPIO and regulators to scuba-iot
  ARM: dts: msm: Add Additional speed bins for supported devices
  ARM: dts: msm: Enable smcinvoke and shmbridge
  ARM: dts: msm: add hgsl to sa8195 vm for GPU doorbell
  ARM: dts: msm: Reorganize the apps_rsc and mxlvl node for sa8195
  ARM: dts: msm: Add configuration for vref regulator vote for YUPIK
  ARM: dts: msm: Add devicetree support for HSP (WCN6850)
  ARM: dts: msm: Enable device nodes for PIL on SM6150
  ARM: dts: msm: Add venus device node for PIL on SM6150
  ARM: dts: msm: Add turing device node for PIL on SM6150
  ARM: dts: msm: Add lpass device node for PIL on SM6150
  ARM: dts: msm: Add SMMU devices for SM6150
  ARM: dts: msm: Add dtsi entry for ssg hlos drivers
  ARM: dts: msm: Add flag to disable the DMA mode
  ARM: dts: qcom: update usb2 phy setting on YUPIK QRD
  ARM: dts: msm: Add dtsi entry for ssg hlos drivers
  ARM: dts: msm: clean up display references for sa8155/sa8195
  dt-bindings: arm: msm: Add entry to disable masking MSI interrupts at EP
  ARM: dts: msm: disable masking MSI interrupts at EP side
  ARM: dts: msm: Update dtsi entries for fastrpc context banks
  ARM: dts: msm: update wsa node for yupik qrd audio
  ARM: dts: msm: add se22 spi alias
  ARM: dts: msm: Add GPII base and GPII IRQ for VM static configs
  ARM: dts: msm: Add pin control for HSP (WCN6850)
  ARM: dts: msm: add audio dt files for sax155 auto platforms
  ARM: dts: msm: Enable touch for 120Hz panel on yupik idp
  ARM: dts: qcom: change ldo for fan controller on Lahaina HHG
  ARM: dts: qcom: enable display on trusted vm for yupik
  ARM: dts: msm: add PMIC devices for SA6150
  ARM: dts: msm: Add UFS support for SA6155
  ARM: dts: msm: Enable L3 interconnect driver for SM6150
  ARM: dts: msm: add interconnect devices for sm6150
  ARM: dts: msm: add pci DT nodes for PCIe switch for sdxlemur
  ARM: dts: msm: Modify IPA DT entry for sdxnightjar
  ARM: dts: msm: bypass new cb for pcie ep
  ARM: dts: msm: Correct the width of APSS TPDM
  ARM: dts: msm: Add 120fps display and touch support Yupik Amoled IDPS
  ARM: dts: msm: add support for CPUCP l3 scaling on yupik target
  ARM: dts: msm: Update EQU_ADAPTOR_CNTRL3 of SS PHY on holi
  ARM: dts: msm: Add device nodes for FastRPC and CDSP Loader for SA8155
  ARM: dts: msm: add quat/quin slpi pinctrl info on sm615x platform
  ARM: dts: msm: Add reserved memory for dfps data on yupik
  ARM: dts: msm: Add node for memory dump driver for SDMSHRIKE
  ARM: dts: msm: Add node for memory dump driver for SM8150
  ARM: dts: msm: Add irq type for uart, watchdog and pinctrl for sdxnightjar
  ARM: dts: msm: correct name of etm0
  ARM: dts: msm: add lxc overlay devicetree for Gen3 platform
  ARM: dts: msm: include display device tree for sa8155/sa8195
  ARM: dts: msm: Add support for secure-level-shifter on sdxnightjar
  ARM: dts: msm: include camera devicetree for sm8150
  ARM: dts: msm: Enable charge pump on sdxlemur platforms
  ARM: dts: msm: Add novatek touch node in yupik trusted VM
  dt-bindings: Add novatek touch vendor name
  ARM: dts: msm: Add trusted touch properties for yupik
  ARM: dts: msm: Add fps entry for yupik
  ARM: dts: msm: Add display and touch support for Yupik Amoled IDP
  ARM: dts: msm: Add support for general interrupts on sdxnightjar
  Revert "ARM: dts: msm: Update kgsl smmu clock for scuba"
  bindings: Documentation: Add new SDK audio properties
  ARM: dts: msm: Disable USB U1/U2 on Olympic
  ARM: dts: msm: Update qpic nand bus vote to nominal voltage
  ARM: dts: msm: Add L1 TLB node for holi
  ARM: dts: msm: Update regulators LDO1C and LDO10C for yupik
  ARM: dts: msm: Add AOPCC for SM6150
  ARM: dts: msm: Disable haptics for yupik atp
  ARM: dts: msm: Add mpm wakeup control capability in yupik pinctrl
  ARM: dts: msm: Add device trees for IDPS with AMOLED for Yupik and YupikP
  ARM: dts: msm: Update the Uni Phy sequence for Olympic
  ARM: dts: msm: update dtsi for wlan pipes holb timeout
  ARM: dts: msm: Correct ATID for tpda dlct
  ARM: dts: msm: enable guest disks renaming
  ARM: dts: msm: Change the node location for optimization for Yupik
  ARM: dts: msm: Add apb_pclk to GMU clock list for Shima
  ARM: dts: msm: Add clocks needed for qos configuration
  ARM: dts: msm: correct the size of etf_reg dump
  dt-bindings: enable guest disks renaming
  ARM: dts: msm: Mark PMIC QUPs as critical clock devices for YUPIK
  dt-bindings: clock: Add qcom,critical-* properties
  ARM: dts: msm: Add glink support for SA6155
  ARM: dts: msm: Update BCL thermalzone configuration for SHIMA
  ARM: dts: msm: Disable DB polling feature for yupik
  dt-bindings: max31760: Add description for the fan cooling device
  ARM: dts: msm: Enable SMMU S1 for WLAN
  ARM: dts: msm: Add camera mux gpio support
  ARM: dts: msm: Add ddr qos devfreq device to yupik  gpu
  ARM: dts: msm: Add tzone-names for yupik GPU
  ARM: dts: msm: Add GCC clock node and GDSCs for MONACO
  ARM: dts: msm: Add cpufreq HW device node SM6150
  ARM: dts: msm: Add clock controllers and gdsc nodes for SM6150
  Revert "ARM: dts: msm: Limit max-frequency for eMMC and SD card"
  ARM: dts: msm: Vote vccq2 via vccq to support GKI
  ARM: dts: msm: Enable pil nodes for scuba
  ARM: dts: msm: Removed wdog for sdxnightjar pil modem
  ARM: dts: msm: Add dma-coherent for tmc-etr on yupik
  ARM: dts: msm: Enable display port for yupik
  ARM: dts: msm: Change wsa spkr node for yupik wsa
  ARM: dts: msm: Add icnss driver for scuba
  ARM: dts: msm: Add support for Lahaina HHG HSP Pro
  ARM: dts: msm: Enable io-coherence hw support for yupik
  ARM: dts: msm: add yupik VM ion chages
  ARM: dts: msm: Disable PMX65 VBUS_DET on sdxlemur MTP-MBB and RCM-RC boards
  ARM: dts: msm: include camera devicetree for sa8195
  ARM: dts: msm: Add vidc node for SA8195
  ARM: dts: msm: Add vidc node for SM8150
  ARM: dts: msm: Add handles for PCIE clocks for Yupik
  ARM: dts: msm: Add support for sec mi2s for fm
  ARM: dts: msm: Add core-hang detect nodes to SDMSHRIKE
  ARM: dts: msm: Add core-hang detect nodes to SM8150
  ARM: dts: msm: Update QSEECOM CMA region
  ARM: dts: msm: Add dt node for restart driver on SDMSHRIKE
  ARM: dts: msm: Add DT node for msm-watchdog in SDMSHRIKE
  ARM: dts: msm: Add dt node for restart driver on SM8150
  ARM: dts: msm: Add DT node for msm-watchdog in SM8150
  dt-bindings: batterydata: Add jeita-fcc-scaling related properties
  Revert "ARM: dts: msm: Disable pmic thermal zone cofiguration"
  ARM: dts: msm: Add open loop CPR support
  dt-bindings: qpnp-smb5: Property to enable JEITA-ARB configuration
  bindings: clock: Add support for MONACO clock controllers
  ARM: dts: msm: set pm8350b_l1 init voltage for qrd yupik
  ARM: dts: msm: Add PMIC and USB support for sdxlemur NTN3 board
  ARM: dts: msm: Add SMB1394 device tree node
  dt-bindings: Add support for GDSC flag to map single GDSCR
  bindings: smb1398: Add support for SMB1394
  ARM: dts: qcom: enable suspend for Lahaina HHG
  ARM: dts: msm: Add regulator and thermal node
  ARM: dts: msm: add cnss device tree
  ARM: dts: msm: Update compatible string for moselle
  ARM: dts: qcom: Add GPU gaming bin support for Yupik
  ARM: dts: msm: Add regulators for SA6155
  dt-bindings: qpnp-lcdb-regulator: Add support for NCP symmetry with LDO
  ARM: dts: msm: remove kgsl smmu interconnect node for Shima
  ARM: dts: msm: disable bias for GPIO81 on Lahaina/Shima QRD
  ARM: dts: msm: add hgsl to sa8155 vm for GPU doorbell
  ARM: dts: msm: Add qfprom for sa8195
  ARM: dts: msm: Add qfprom for sa8155
  ARM: dts: msm: remove PON_PBS peripheral for yupik
  ARM: dts: msm: Add PMU device nodes for SDMSHRIKE
  ARM: dts: msm: Add devfreq device nodes for SDMSHRIKE
  ARM: dts: msm: Add PMU device nodes for SM8150
  ARM: dts: msm: Add device trees for sa8195 virtual machine
  ARM: dts: msm: Update max voltage for each regulator
  ARM: dts: msm: add cont splash memory for yupik target
  ARM: dts: msm: Add support for kgsl driver on sdmshrike
  ARM: dts: msm: Add support for kgsl driver on SA8155
  ARM: dts: msm: Enable smmu s1 on sdxlemur V2
  ARM: dts: msm: Disable pmic thermal zone cofiguration
  ARM: dts: msm: add pm-qos-latency for Lahaina usb
  ARM: dts: msm: Add yupik camera sensor device tree to Yupik QRD
  ARM: dts: msm: add CMA heap allocation
  ARM: dts: msm: update cpu core frequency corners in mapping table
  ARM: dts: msm: Add SPS node for Yupik
  ARM: dts: msm: Add alias for serial device to ensure proper enumeration
  ARM: dts: msm: Enable wcn bt for yupik
  ARM: dts: qcom: add sde-rsc-rpmh driver to disp_rsc node
  ARM: dts: msm: Enable L3 interconnect driver for Yupik
  ARM: dts: msm: Update GPU FMAX for yupik GPU
  dt-bindings: interconnect: add interconnect bindings for sm6150
  ARM: dts: msm: Add hab and peripherals for sa8155 vm
  ARM: dts: msm: update widget name for Lahaina HHG device
  ARM: dts: msm: Add devfreq device nodes for SM8150
  ARM: dts: msm: Add Display and Touch support on yupik atp
  ARM: dts: qcom: Add SPI touch node for QRD yupik
  ARM: dts: msm: Add vreg.sp and gpio.sp resources for lahaina
  ARM: dts: msm: include display qrd nodes for yupik qrd
  ARM: dts: msm: Add i2c, spi, uart dtsi nodes for monaco
  ARM: dts: msm: Enable PCIe RC on sdxnightjar
  ARM: dts: msm: Add necessary changes for CQE enablement on sdxlemur
  ARM: dts: msm: Enable dlct tpdm on yupik
  ARM: dts: msm: Add thermal zone entries for pm8195
  ARM: dts: msm: Add bus voting support for sdxlemur
  ARM: dts: msm: Enable forcce-hard-reset option for sdxnightjar
  ARM: dts: msm: Change some coresight component names
  ARM: dts: msm: Disable SDCC TPDMs on shima
  ARM: dts: msm: Mark GCC USB30 secondary clocks as protected on YUPIK
  ARM: dts: msm: Limit max-frequency for eMMC and SD card
  ARM: dts: msm: Add  pmic dependency back on Yupik
  ARM: dts: msm: Add yupik camera sensor device tree to Yupik IDP
  ARM: dts: msm: Add cpuidle states and stats driver nodes for sm6150
  ARM: dts: msm: Add cmd_db, RSC and PDC devices for sm6150
  ARM: dts: msm: Early mount of vendor partition
  ARM: dts: msm: Enable smmu for eMMC on shima
  ARM: dts: msm: Update GPU speed bins for yupik
  ARM: dts: msm: Add ion device for sdxnightjar
  ARM: dts: msm: Map more no of redistributors for monaco
  ARM: dts: msm: Add support for qca6490 xo clk gpio
  ARM: dts: msm: Add entry to handle XO clock gpio
  ARM: dts: msm: Change QSEE,glink IRQs to level trigger
  ARM: dts: msm: Add device node for llcc node on SDMSHRIKE
  ARM: dts: msm: Add device node for llcc on sm8150
  ARM: dts: msm: disable tpdm sdcc on holi
  ARM: dts: msm: Add support for Moselle (WCN6750)
  dt-bindings: ufs: Add compitable string for V3 UFS PHY on SM6150
  bindings: clock: Add support for SM6150 clock controllers
  ARM: dts: msm: Rectify DT flags and GPII mask for TUI VM usecase
  ARM: dts: msm: Correct bluetooth node name for sdxnightjar
  ARM: dts: msm: Add cooling-cells property in mdss_mdp device for yupik
  ARM: dts: msm: Enable device nodes for PIL on SDMSHRIKE
  ARM: dts: msm: Add spss device node for PIL on SDMSHRIKE
  ARM: dts: msm: Add venus device node for PIL on SDMSHRIKE
  ARM: dts: msm: Add npu device node for PIL on SDMSHRIKE
  ARM: dts: msm: Add turing device node for PIL on SDMSHRIKE
  ARM: dts: msm: Add lpass device node for PIL on SDMSHRIKE
  ARM: dts: msm: Add scm & scm-pas device on SDMSHRIKE
  ARM: dts: msm: Fix wdog interrupts on pil subsystems for SM8150
  ARM: dts: msm: Enable device nodes for PIL on SM8150
  ARM: dts: msm: Add venus device node for PIL on SM8150
  ARM: dts: msm: Add turing device node for PIL on SM8150
  ARM: dts: msm: Add npu device node for PIL on SM8150
  ARM: dts: msm: Add spss device node for PIL SM8150
  ARM: dts: qcom: Update Audio dtsi entries
  ARM: dts: msm: Add a new pinctrl state for lahaina
  ARM: dts: msm: Include display nodes for yupik target
  ARM: dts: msm: add touch support on yupik target
  ARM: dts: msm: Enable dcc for yupik
  ARM: dts: msm: Add support for FM in yupik platform
  ARM: dts: qcom: enable fan controller for Lahaina HHG
  ARM: dts: msm: enable more SIDs
  ARM: dts: msm: update interconnect and global interuupts on yupik
  ARM: dts: msm: Update extcon for USB on sdxnightjar
  ARM: dts: msm: Add support for sysdev on sdxnightjar
  ARM: dts: msm: Correct dtsi file for Lahaina HHG non-overlay dts
  dt-bindings: Document usage of qcom,ignore-wakeup-src-in-hostmode
  ARM: dts: msm: Add a new pinctrl state for yupik
  ARM: dts: msm: add mem_dump entry for sdxnightjar
  ARM: dts: msm: Add LCDB and WLED devices for PM7325B
  dt-bindings: qpnp-lcdb-regulator: Add support for PM7325B LCDB
  ARM: dts: msm: Add devfreq-cpufreq for SDXNIGHTJAR target
  ARM: dts: msm: Add BCL and PMIC die temperature mitigation for yupik
  ARM: dts: msm: Add GPU thermal zone configuration for YUPIK
  ARM: dts: msm: Add QMI sensor and cdev configuration for YUPIK
  ARM: dts: msm: Add CPU thermal configuration for yupik
  ARM: dts: msm: Add UFS ICE HW controlled clock for yupik
  ARM: dts: msm: Update kgsl smmu clock for scuba
  ARM: dts: msm: Add support for diff yupik sku
  ARM: dts: msm: Modify IPA DT entry for sdxnightjar target
  ARM: dts: msm: Update max bus vote range for Holi
  ARM: dts: msm: Add lpass device node for PIL on SM8150
  ARM: dts: msm: Add platform dt changes for yupik for ufs
  ARM: dts: msm: Add GPU properties for yupik GPU
  ARM: dts: msm: Add cpufreq-hw-debug node for Lahaina
  dt-bindings: backlight: Add support for PM7325B WLED
  ARM: dts: msm: Correct soc id for monaco
  ARM: dts: msm: Update DISPCC and debugcc clock nodes for YUPIK
  ARM: dts: msm: Remove pmic dependency on Yupik
  bindings: Add device-tree bindings for slatecom interface driver
  ARM: dts: msm: Add smp2p sleepstate node for yupik
  ARM: dts: qcom: Enable haptics node for yupik atp
  ARM: dts: msm: Add audio overlay for yupik
  ARM: dts: msm: Add pin configuration for USB3 PHY portselect on Yupik
  ARM: dts: msm: Add iommu and h/w reset support for yupik
  ARM: dts: msm: update apps smmu interrupt list
  ARM: dts: msm: Mark GCC PCIE clocks as protected in YUPIK
  bindings: Add device-tree bindings for slatecom SPI driver
  ARM: dts: msm: Adding CoreTech sa8195 DT Changes to Mainline 5.4
  ARM: dts: msm: Add scm dt nodes for sdxnightjar
  ARM: dts: msm: Add I2C NFC device node and LDO voting for yupik
  ARM: dts: msm: Adding IPA nodes for yupik target
  ARM: dts: msm: Added pil nodes for sdxnightjar
  ARM: dts: qcom: swap WSA enable pin
  ARM: dts: msm: Add SMP2P entry and enable SIDs for WLAN
  bindings: Add device-tree bindings for pil-q6v5 driver
  ARM: dts: msm: add remote debugger support
  ARM: dts: msm: Add SDIO support for sdxnightjar
  ARM: dts: msm: Add feature config node for qfprom for Yupik
  ARM: dts: msm: Update GIC interrupt polarity for Yupik
  ARM: dts: msm: add dcvs nodes for yupik target
  dt-bindings: add documentation for max31760 fancontroller
  ARM: dts: msm: add bindings for HGSL driver
  ARM: dts: msm: Add device node for PIL scm pas on SM8150
  ARM: dts: msm: Add camera device pinctrl change for Yupik camera
  ARM: dts: msm: Add slpi device node for PIL on SM8150
  ARM: dts: msm: Add modem device node for PIL SM8150
  ARM: dts: msm: Add device node for IMEM on SM8150
  dt-bindings: ufs: Add compatible string for yupik phy driver
  ARM: dts: qcom: Add dtsi entry for BT slimbus in yupik
  ARM: dts: msm: Enable SMB1351 for sdxnightjar
  ARM: dts: msm: Enable bluetooth for sdxnightjar
  ARM: dts: msm: correct refgen type for holi
  ARM: dts: msm: Add cpu clock node for sdxnightjar
  ARM: dts: msm: Correct QUPv3 device nodes
  ARM: dts: msm: remove kgsl smmu interconnect node for Lahaina
  ARM: dts: msm: enable HOLB monitor feature
  ARM: dts: msm: Add support for ddr scaling on sdxlemur
  ARM: dts: msm: Add device node for ARM PMU for Olympic
  ARM: dts: msm: Add bindings for ARM performance measuring unit
  dt-bindings: Add dt binding for NT36xxx driver
  ARM: dts: msm: Add fastrpc and cdsp/adsp device node
  ARM: dts: msm: Introduce demura HFC region nodes
  ARM: dts: msm: Add pinctrl information for Yupik target
  ARM: dts: msm: Add thermal zones for pm2250
  ARM: dts: msm: Change DT configuration for PMIC GPIO device
  ARM: dts: msm: Change address-cells to 1 for pm2250
  ARM: dts: msm: Add tlmm pinctrl support for SM6150
  ARM: dts: msm: Add minidump id for LPASS/CDSP on Yupik
  ARM: dts: msm: Enable qsee drivers for yupik
  ARM: dts: msm: Add device tree files for sdxlemur v2
  ARM: dts: msm: Revised RCM RC variant id for sdxlemur
  ARM: dts: msm: Add IPA DT entry for sdxnightjar target
  ARM: dts: msm: Add Modem pil node for Yupik
  ARM: dts: msm: Signal aop change for PIL for YUPIK
  ARM: dts: msm: Add qfprom and qfprom_sys node
  ARM: dts: msm: Add bus voting and platform support for yupik
  ARM: dts: qcom: Add node to enable haptics on yupik qrd
  ARM: dts: msm: Add ion support for SDMSHRIKE
  ARM: dts: msm: add stub interconnect devices for Monaco
  ARM: dts: msm: Add slpi pinctrl to SDMSHRIKE
  ARM: dts: msm: Remove duplicated smem_mem on SDXNIGHTJAR
  ARM: dts: msm: Add support for CPUFREQ HW for YUPIK
  ARM: dts: msm: Add TSENS node support for yupik
  ARM: dts: msm: Add pm-qos-latency for Yupik
  ARM: dts: msm: Add SMMU nodes for Yupik
  ARM: dts: msm: Add USB Phy Support on Yupik
  ARM: dts: msm: Disable haptics for yupik idp
  ARM: dts: msm: Add idle states for sdmshrike
  ARM: dts: msm: Add a new pinctrl state for holi
  ARM: dts: msm: Update the APSSCC clock node for SDXLEMUR
  ARM: dts: msm: add node in device tree for yupik QRD
  ARM: dts: msm: add setting for Lahaina HHG audio
  ARM: dts: msm: Add GDSC for HS USB PHY for SDXNIGHTJAR
  ARM: dts: msm: Add new DT file for Dual WIFI support for sdxnightjar
  dt-bindings: spi-msm-geni: Define fixed timeout property
  dt-bindings: add bindings for HAB driver
  ARM: dts: msm: Update regulators for yupik
  ARM: dts: msm: Add platform-specific PMIC changes for yupik
  ARM: dts: msm: Add initial device tree for Lahaina HHG
  ARM: dts: msm: Add ddr qos devfreq device to lahaina gpu
  ARM: dts: msm: Add l3 endpoints and pwrlevels for gpu
  ARM: dts: msm: device nodes for SVM usecases on yupik
  bindings: clock: Add CPU clock controller bindings for SDXNIGHTJAR
  ARM: dts: msm: Update CMA region for monaco
  ARM: dts: msm: Add mem_dump node for yupik
  ARM: dts: msm: Rectify all BLSP QUP nodes with correct clocks
  ARM: dts: msm: Update ion heap for scuba
  ARM: dts: msm: Add SMMU devices for sdmshrike
  ARM: dts: msm: define mem offline node in yupik
  ARM: dts: qcom: add refgen regulator device for yupik
  ARM: dts: msm: Add coreisght device tree for yupik
  ARM: dts: msm: Update memory map for SDXNIGHTJAR target
  ARM: dts: msm: Add dcc node for yupik
  dt-bindings: interconnect: add interconnect bindings
  ARM: dts: msm: Add camera device tree inclusions for Yupik camera
  ARM: dts: msm: Add dtsi nodes for i2c, spi and hsuart
  ARM: dts: msm: add UCSI connector and USB port on Yupik
  ARM: dts: msm: Add USB BAM device node on sdx12
  ARM: dts: qcom: Add second trip to quiet-therm-usr for holi
  ARM: dts: msm: Update labels for sdxnightjar regulators
  ARM: dts: msm: Add TUI support over SPI and I2C on LE VM for Yupik
  ARM: dts: msm: add PMIC devices for SCSHRIKE
  ARM: dts: msm: Add UFS support for SDMSHRIKE
  ARM: dts: msm: Add device trees for YupikP variant
  ARM: dts: msm: add interconnect devices for sdxnightjar
  ARM: dts: msm: Add QDSS devictree for sdxnightjar
  ARM: dts: msm: correct modem etm0 connecton on sdxlemur
  ARM: dts: msm: Adding all CoreTech DT Changes to Mainline 5.4
  ARM: dts: msm: Remove sdxlemur dt from pcie-ep dtsi
  Revert "ARM: dts: msm: add initial support for hw memlat devices"
  ARM: dts: msm: Add EUD node for Yupik
  ARM: dts: msm: Add MPROC device nodes for monaco
  ARM: dts: msm: add DCC register list for sdxlemur
  ARM: dts: msm: fix USB2 issue on holi QRD DVT
  ARM: dts: msm: Disable USB SMMU S1 on sdxlemur pcie ep platform
  ARM: dts: msm: Enable L3 interconnect driver for scshrike
  ARM: dts: msm: Add cpufreq HW device node SDMSHRIKE
  ARM: dts: msm: Add all clock controller and gdsc nodes for scshrike
  ARM: dts: msm: Add support for glink for SDMSHRIKE
  ARM: dts: msm: add interconnect devices for scshrike
  dt-bindings: Update for CNSS driver to support WCN7850 device
  ARM: dts: msm: add conn_therm and charger_skin_therm for sdxlemur platforms
  ARM: dts: msm: Split tz mem region for sdxlemur
  ARM: dts: msm: Update power source for PM8350C GPIOs for yupik
  ARM: dts: msm: Add apb_pclk to GMU clock list for Lahaina
  dt-bindings: interconnect: add interconnect bindings for SDXNIGHTJAR
  ARM: dts: msm: Add ACD control register values for Shima GPU
  ARM: dts: msm: Add wdi2 support for holi
  ARM: dts: msm: add actlr settings for yupik
  ARM: dts: msm: Update clocks and clock-names of GCC node for YUPIK
  ARM: dts: msm: Add video device for Yupik
  ARM: dts: msm: add the current load parameter for vdd reg
  ARM: dts: msm: Update CAMCC clock node for YUPIK
  ARM: dts: msm: add PMIC devices for SM8150
  ARM: dts: msm: Add system_pm device for SDMSHRIKE
  ARM: dts: msm: Add Power management nodes for SDMSHRIKE
  ARM: dts: msm: Add regulators for SDMSHRIKE
  ARM: dts: msm: Add RSC and cmd_db support for SDMSHRIKE
  dt-bindings: clocks: Add clock controller bindings for SCSHRIKE
  dt-bindings: interconnect: add interconnect bindings
  ARM: dts: msm: Add the SMMU devices for SM8150
  arm64: dts: qcom: sm8150: Add cpufreq HW device node
  ARM: dts: qcom: Add slimbus dtsi node for monaco
  ARM: dts: msm: Update interrupt configuration for sdxnightjar
  ARM: dts: msm: Add initial device tree for Quin virtual machine
  ARM: dts: msm: Update VideoCC node and Multimedia GDSC's for YUPIK
  ARM: dts: qcom: Add second trip to quiet-therm userspace rule for SHIMA
  ARM: dts: msm: Revised emmc device tree and added to makefile
  ARM: dts: msm: Add venus pil node for Yupik
  ARM: dts: msm: Update drive strength values for sdc1 node on shima
  ARM: dts: msm: Add audio dtsi changes for yupik
  ARM: dts: msm: Enable download/restart mode drivers for Yupik
  ARM: dts: msm: Enable USB bus suspend functionality on sdxlemur
  ARM: dts: msm: Update ddr variant for all sdxlemur 512mb variants
  ARM: dts: msm: Add SPS node for monaco
  ARM: dts: qcom: Add second trip to xo-therm userspace rule for lahaina
  ARM: dts: msm: Enable qcedev and qcrypto on olympic
  dt-bindings: interconnect: update OSM L3 bindings
  Revert "ARM: dts: msm: add initial support for hw memlat devices"
  bindings: interconnect: Update OSM L3
  ARM: dts: msm: Remove test devices for sdxlemur v1
  ARM: dts: msm: Add initial device tree for SA6155
  ARM: dts: msm: Add bcm voter devices for Yupik
  ARM: dts: msm: Add dma-coherent for tmc-etr on Lahaina
  ARM: dts: msm: Update the init-mode of LDO11C for shima
  ARM: dts: msm: Add QDSS IPA bam connection config for sdxlemur
  ARM: dts: msm: Add Superspeed PHY node on sdxnightjar
  ARM: dts: msm: Add USB nodes for SDXNIGHTJAR
  ARM: dts: qcom: enable hypervisor core_ctl for Yupik
  ARM: dts: msm: Add support for SM8325 platforms
  ARM: dts: msm: Add SPS node for SDXNIGHTJAR
  ARM: dts: msm: Add clock controller nodes for SDXNIGHTJAR
  ARM: dts: msm: Add Yupik trustedVM device configuration
  ARM: dts: msm: Add PIL node for WPSS in Yupik DTSI
  ARM: dts: msm: Add reserved region for uefi for holi
  ARM: dts: qcom: update redriver of shima/lahaina QRD
  ARM: dts: msm: Update ddr subtype for 512mb variant
  ARM: dts: qcom: Add entries for audio overlay
  ARM: dts: msm: Fix pmx65 die_temp configuration
  ARM: dts: msm: Enable tzlog driver on sdxlemur
  ARM: dts: msm: Increase max voltage of S11B regulator
  ARM: dts: msm: Add label for llcc
  ARM: dts: msm: Add initial device tree for Yupik for QRD
  ARM: dts: qcom: Add dtsi node entry for Slimbus in yupik
  bindings: clock: Add clock controller bindings for SDXNIGHTJAR
  ARM: dts: msm: Enable NAND and SD card for sdxnightjar
  ARM: dts: msm: Add a 5C hysteresis for DDR rule in Lahaina
  bindings: mproc: add smdpkt.txt
  ARM: dts: msm: Configure I2C pinctrl setting as per codec requirement
  ARM: dts: msm: Add secondary controller USB nodes for Yupik
  ARM: dts: msm: Add rmtfs_sharedmem support for yupik
  ARM: dts: msm: Added warm reset for sdxlemur pcie devices
  ARM: dts: msm: Update spmi_bus configuration for sdxnightjar
  ARM: dts: msm: add interconnect paths for smmu
  ARM: dts: msm: Add PMIC support for monaco
  dt-bindings: pinctrl: qcom-pmic-gpio: add PM7325 and PM7325B bindings
  ARM: dts: msm: Add PM8008 support for yupik
  ARM: dts: msm: Add PMIC support for yupik
  ARM: dts: msm: increase vddio voltage for hdk r66451 dsi panel
  ARM: dts: msm: Add support for Lahaina HSP Pro
  ARM: dts: msm: Add ddr type to the subtype for sdxlemur
  ARM: dts: msm: Add extcon node for sdxlemur platforms
  ARM: dts: msm: Add L3 snoop bw device on Lahaina
  ARM: dts: msm: Add cpu7 qos latfloor device on shima
  ARM: dts: msm: Add support for TUI over SPI on LE VM
  ARM: dts: msm: Add support of clock AOP for YUPIK
  ARM: dts: msm: Update ion heap for monaco
  ARM: dts: msm: Update tune params of HS PHY
  ARM: dts: msm: Add SMMU device tree for Monaco
  ARM: dts: msm: add new properties to guestvm node
  dt-bindings: Update bindings for guestvm-loader
  ARM: dts: msm: Add clock support for uart driver
  ARM: dts: msm: Disable atmel_mxt_ts on shima
  ARM: dts: msm: Increase max voltage of S11B regulator to 2.04V
  ARM: dts: msm: Enable PCIe EP on sdxlemur MBB
  ARM: dts: msm: Add PCIe EP and MHI device for sdxlemur
  ARM: dts: msm: Make sdhc aliases start from 0
  ARM: dts: msm: remove SMB1398 clock frequency setting on holi
  ARM: dts: msm: update PMU cache and log buffer addresses for holi target
  ARM: dts: msm: add no-memory-wc to sram node for holi
  ARM: dts: msm: Add eMMC, SD card support for yupik
  ARM: dts: msm: Add initial device tree for Yupik for IDP/ATP
  ARM: dts: msm: Add ICNSS2 DT node for Yupik
  ARM: dts: msm: Add camera device tree inclusions for lahaina hdk
  ARM: dts: msm: Bind emmc and sdcard slot to 0 & 1
  ARM: dts: msm: Bind sdcard to slot 1
  ARM: dts: msm: Add support for RPMHCC for YUPIK
  ARM: dts: msm: Add dma coherent flag for ufs
  ARM: dts: msm: Change micbias no for VA DMIC for shima
  ARM: dts: msm: switch off kpti on shima/lahaina/yupik
  ARM: dts: qcom: use separate thermal zone names for modem pa for shima
  ARM: dts: msm: Add trustedvm enablement nodes for Yupik
  ARM: dts: qcom: Add RPMh controlled PMIC regulators for yupik
  ARM: dts: msm: Enable KPDPWR software debounce for PMK8350
  ARM: dts: msm: update PMU cache and log buffer addresses for holi target
  Revert "ARM: dts: msm: Add dma-coherent for tmc-etr on Lahaina"
  dt-bindings: qpnp-amoled: add support to disable pulse skipping
  ARM: dts: msm: Make sdhc aliases start from 0
  ARM: dts: qcom: update skin sensor modem mitigation threshold for shima
  ARM: dts: msm: Enable mproc drivers for SDXNIGHTJAR
  Revert "ARM: dts: msm: Disable PMX65 VBUS_DET on sdxlemur MTP-MBB and RCM-RC boards"
  ARM: dts: msm: add no-memory-wc to sram node for holi
  dt-bindings: input: qpnp-power-on: Update "reg" property description
  ARM: dts: msm: Update interconnect nodes for YUPIK
  dt-bindings: interconnect: update interconnect bindings
  ARM: dts: msm: Update BCL, Alarm and CPU thermal mitigation for SHIMA
  ARM: dts: msm: Update thermal mitigation config for SHIMA
  ARM: dts: msm: Add jtagv8 devices for yupik
  ARM: dts: msm: remove SMB1398 clock frequency setting on holi
  ARM: dts: msm: Remove bluetooth bootstrap pin EDL_MODE settings
  ARM: dts: msm: update generic PCI node name on sdxlemur
  ARM: dts: msm: Add USB PHY related PDC interrupts and enable on sdxlemur
  ARM: dts: qcom: Change cci3 gpio function from cci to gpio
  ARM: dts: qcom: Update skin and cx thermal config for HOLI
  ARM: dts: msm: Update the rpm-smd node with IRQ for sdxnightjar
  ARM: dts: msm: Add a new pinctrl state for shima
  ARM: dts: msm: modify dcc_ram_offset for sdxlemur
  ARM: dts: msm: refine QDSS config for sdxlemur
  ARM: dts: msm: Add interconnect osm l3  devices for SM8150
  ARM: dts: msm: Add UFS support for SA8155
  ARM: dts: msm: add interconnect devices for sm8150
  ARM: dts: msm: Add clock controller and gdsc nodes for sm8150
  ARM: dts: msm: Add dma-coherent for tmc-etr on Lahaina
  ARM: dts: msm: Add boot_stats node for Yupik
  ARM: dts: msm: add msm_rtb tracing
  ARM: dts: msm: Enable NAND and SD card for sdxlemur target
  ARM: dts: msm: Enable bluetooth for sdxlemur
  ARM: dts: msm: Add label for bluetooth bootstrap pin EDL_MODE on sdxlemur
  ARM: dts: msm: DDR cooling device no mitigation for lahaina
  dt-bindings: arm: msm: add entry for number of PARF testbus selectors
  ARM: dts: msm: add number of PARF testbus selectors for shima
  ARM: dts: msm: add number of PARF testbus selectors for sdxlemur
  ARM: dts: msm: add number of PARF testbus selectors for lahaina
  ARM: dts: msm: Support CNSS WLAN device for sdxlemur
  ARM: dts: msm: Add new GPU DCVS corners for Shima
  ARM: dts: msm: Add dummy clock nodes for MONACO
  ARM: dts: msm: Disable scaling for SD and eMMC on sdxlemur
  ARM: dts: msm: Update GPUCC clock node and GDSC for YUPIK
  ARM: dts: msm: Update GCC clock node and GDSC for YUPIK
  ARM: dts: msm: Add missing memory map region for sdxlemur
  ARM: dts: msm: Disable PMX65 VBUS_DET on sdxlemur MTP-MBB and RCM-RC boards
  ARM: dts: msm: Reduce secure heap to 30MB
  ARM: dts: qcom: add ADC channels for pm8350b and smb139x on shima
  ARM: dts: msm: Add ion heap for monaco
  ARM: dts: msm: specify thermal mitigation levels for sdxlemur platforms
  ARM: dts: msm: Add initial v1 memory map for Monaco
  ARM: dts: msm: add gfx smmu node on yupik
  ARM: dts: msm: add spmi_debug_bus for sdxlemur
  ARM: dts: msm: update pm7250b devices for sdxlemur platforms
  ARM: dts: msm: Enable eMMC for sdxlemur target
  ARM: dts: msm: Add CDSP pil node for Yupik
  ARM: dts: msm: Add LPASS pil node for Yupik
  ARM: dts: msm: Add scm pas node
  ARM: dts: msm: Enable SMMU and PSCI for scuba
  ARM: dts: msm: Add QUPv3 SE and GPI DT nodes for yupik
  ARM: dts: msm: Add PMX65 die temperature channel
  ARM: dts: msm: Turn off KPTI for Lahaina
  ARM: dts: qcom: Update skin and cx thermal config for HOLI
  ARM: dts: msm: Remove display clock as client for CX SDPM for SHIMA
  ARM: dts: msm: keep PCIe in EQ Master Phase for at least 1ms on sdxlemur
  dt-bindings: arm: msm: add support for tuning PCIe EQ Master Phase
  ARM: dts: msm: add MX entries for PCIe on sdxlemur
  ARM: dts: msm: Add IOMMU Geometry property for storage
  bindings: SMB358: Add documentation for smb358 charger
  ARM: dts: msm: Include sdxlemur-mtp dt on all mtp trees
  ARM: dts: msm: Add eMMC device tree files for sdxlemur
  dt-bindings: clock: Add support for YUPIK clock controllers
  ARM: dts: msm: add touch for 144hz panel
  ARM: dts: msm: Move firmware node ahead
  ARM: dts: msm: Change the node location for optimise
  ARM: dts: msm: Add pmd9650 gpio nodes for SDXNIGHTJAR
  ARM: dts: qcom: Change cci3 gpio function from cci to gpio
  ARM: dts: msm: Update the rpm-smd node with correct IRQ for holi
  ARM: dts: qcom: update JEITA FCC threshold for alium 3600mAh battery
  ARM: dts: msm: update PCIe1 to support m.2 and generic EP on lahaina HDK
  ARM: dts: msm: Enable touch for Dual DSI video mode on shima
  ARM: dts: msm: Add initial devicetrees for SDXNIGHTJAR target
  ARM: dts: msm: Update PCIe PHY settings to v1.02 for sdxlemur
  ARM: dts: msm: add LTR entries for HSP direct connects on sdxlemur
  ARM: dts: msm: Add pm-qos-latency for Shima
  dt-bindings: arm: Add FUSE and DBGUI support
  ARM: dts: msm: add PCI DT node for generic attaches over oculink sdxlemur
  ARM: dts: msm: Correct BAM register address on olympic
  ARM: dts: msm: increase log buf size for holi
  ARM: dts: msm: Add le-vm DT flag in lahaina TUI
  ARM: dts: msm: Disable unused flag for MDM
  dt-bindings: interconnect: add OSM L3 bindings
  dt-bindings: ufs: Add compitable string for V4 UFS PHY on SM8150
  dt-bindings: interconnect: update interconnect bindings
  ARM: dts: qcom: Add entry for EUD driver
  ARM: dts: msm: Include stub regulators for Monaco
  ARM: dts: msm: Add the hwkm ice slave regions to storage node
  ARM: dts: msm: enable scmi plh protocol
  dt-bindings: clocks: Add clock controller bindings for SM8150
  ARM: dts: msm: Add support for glink for SM8150
  ARM: dts: msm: Add initial device tree for Monaco
  ARM: dts: msm: Disable sdcard on cdp & eMMC on mbb platform
  ARM: dts: msm: Add PMIC devicetrees for SDXNIGHTJAR
  ARM: dts: msm: Add RDPM register map for Shima GPU
  ARM: dts: msm: Use PCIe_MSI for Shima
  ARM: dts: msm: Change the node location for optimization for Shima
  ARM: dts: msm: Add stub regulators for Monaco
  ARM: dts: msm: Add v2 MTP VM device tree file for lahaina VM
  ARM: dts: msm: Add DCC register list for holi
  ARM: dts: msm: Update regulator S3A for holi
  ARM: dts: msm: Add vdd parent supply for holi GPU
  ARM: dts: msm: Enable SCMI PLH protocol
  ARM: dts: msm: correct PCIe regulator labels for sdxlemur
  ARM: dts: msm: Reorganize the apps_rsc node for Lahaina
  dt-bindings: arm: msm: support tuning of PCIe EQ preset request vector
  Revert "ARM: dts: msm: Enable SCMI PLH protocol"
  ARM: dts: msm: Add S3 die_temp channel for scuba
  bindings: mproc: Add support for sm8150 mailbox string
  bindings: qcom-pmic-gpio: Add PMD9650 binding
  ARM: dts: msm: Enable qcom,power-always-on for GPU SMMUs on GKI targets
  dt-bindings: Document the qcom,power-always-on property for SMMU devices
  ARM: dts: qcom: Add entries for power off/downlaod mode driver
  ARM: dts: qcom: Add MicroUSB support for Holi
  ARM: dts: msm: Add dmips and dynamic power co-efficient for Yupik
  ARM: dts: msm: Update the rpm-smd node with correct IRQ for holi
  ARM: dts: msm: Add secure display heap configuration for Yupik
  ARM: dts: msm: Add DCC register list for holi
  ARM: dts: msm: Add DDR cooling device for Lahaina
  ARM: dts: msm: Add vmid cdsprpc-smd for Holi
  ARM: dts: msm: Add GPU mitigation rules for Lahaina QRD
  ARM: dts: msm: adjust pm6150a_l1 initial voltage for Holi platforms
  ARM: dts: msm: Add cti trig_out gpio for shima
  dt-bindings: Add DDR cooling device
  ARM: dts: msm: Correct GCC clocks for UART instances
  ARM: dts: msm: Enable touch for Dual DSI panel on shima
  ARM: dts: msm: Add cphy video/cmd mode touch support on shima
  ARM: dts: msm: Add configuration for vref regulator vote for SHIMA
  ARM: dts: msm: Add CX and MX SDPM configuration for SHIMA
  ARM: dts: msm: Add rmtfs_sharedmem support for scuba-iot
  Revert "ARM: dts: msm: enable mem_offline.bypass_send_msg for holi"
  ARM: dts: msm: Disable dma-coherent for IPA CBs on SDXLEMUR
  ARM: dts: qcom: Added msm-id entry for single-die sdxlemur
  ARM: dts: msm: Keep default PM level setting for Lahaina
  ARM: dts: msm: Add missing changes to shima-atp dtsi
  ARM: dts: msm: Add acd registers for HOLI
  ARM: dts: msm: Add Wakeup interrupt controller for scuba-iot
  bindings: qcom-hv-haptics: add properties to support non-HBoost regulator
  ARM: dts: qcom: Enable TSENS driver support for sdxlemur
  ARM: dts: msm: disable GPU funnel
  ARM: dts: msm: Update PCIe LDO clock from CXO to CXO_A
  ARM: dts: msm: Update regulator S3A for holi
  ARM: dts: msm: add system ion heaps on yupik
  ARM: dts: msm: Add bindings for PCIe end point driver
  ARM: dts: msm: Add vdd parent supply for holi GPU
  Revert "ARM: dts: msm: Add new DT entry for wan agg pkt size"
  ARM: dts: msm: Add QUPv3_0 and SE5 dt nodes for YUPIK
  ARM: dts: msm: Remove touch vote for L8C on shima
  ARM: dts: msm: Add PM7250B to select sdxlemur boards
  ARM: dts: msm: Add PMIC overlay to all sdxlemur platforms
  ARM: dts: msm: Add change for smmu memory optimizations
  dt-bindings: arm: Add reset/flush CTI trigger number support
  ARM: dts: msm: add smmu nodes on yupik
  ARM: dts: msm: add MX entries to qcom,bw-scale for PCIe on shima
  ARM: dts: msm: add MX entries to qcom,bw-scale for PCIe on lahaina
  dt-bindings: arm: msm: add MX entries for PCIe
  ARM: dts: msm: Configure USB SMMU in atomic mode on sdxlemur
  ARM: dts: qcom: add physical addr for swr tx slaves of Holi
  ARM: dts: msm: Set emmc vdd-io regulator in NPM mode during sleep
  ARM: dts: msm: Add slimbus dtsi node for scuba
  ARM: dts: msm: Add cti trigger number to device tree for holi
  ARM: dts: msm: Add cti trigger number to device tree for lahaina
  ARM: dts: msm: Increase MHI event rings number for SDXLEMUR
  ARM: dts: msm: add PCIe AUX CLK freq entry for PCIe0 and PCIe1 for lahaina
  ARM: dts: msm: Add eMMC, SD card support for sdxlemur
  ARM: dts: msm: Update S2C min voltage for shima
  ARM: dts: msm: add l3 latfloor in shima target
  ARM: dts: msm: disable IPA TPDM
  ARM: dts: msm: Change IPA bandwidth threshold value for holi target
  ARM: dts: msm: Enable SCMI PLH protocol
  ARM: dts: msm: Add interconnect bus voting values to Holi
  ARM: dts: qcom: Add quiet-therm thermal zone mitigation for HOLI
  ARM: dts: msm: add trusted touch support in PVM for Lahaina
  ARM: dts: msm: Remove modem tsens QMI thermal zone for Lahaina
  ARM: dts: msm: Reduce the IOVA range for slimbus and QUP usecases
  ARM: dts: msm: Reduce the IOVA range for QUP usecase
  ARM: dts: msm: Update masks in codec Fs clock sequence
  ARM: dts: msm: Add cti trigger number to device tree for shima
  ARM: dts: msm: Add ARM PMU node for Yupik
  ARM: dts: msm: Enable Kryo erp driver for Yupik
  ARM: dts: msm: Add core hang detection for Yupik
  ARM: dts: msm: add PCIe AUX clk freq for controller for sdxlemur
  ARM: dts: msm: move qcom,boot-option to HSP dedicated DTSI for sdxlemur
  ARM: dts: msm: Add usb bam dt node on sdxlemur
  ARM: dts: msm: Add a new power level for supported devices
  Revert "ARM: dts: msm: Use PCIe_MSI for Shima"
  ARM: dts: msm: Add ipcc test nodes for Yupik
  ARM: dts: msm: select visionox panel and touch controller for TVM
  ARM: dts: msm: Add LLCC entry for Yupik
  ARM: dts: msm: Add MPROC device nodes for scuba
  dt-bindings: LLCC: Add compatible property for Yupik
  ARM: dts: qcom: Update skin and cx thermal mitigation config for SHIMA
  Revert "ARM: dts: msm: disable mem-offline node"
  ARM: dts: msm: Add v2.1 MTP VM device tree file for Lahaina VM
  ARM: dts: msm: Update silver core mitigation for Lahaina
  ARM: dts: msm: Update PSCI state id for yupik
  bindings: mproc: Add support for scuba and monaco mailbox strings
  ARM: dts: msm: Add bootargs for Yupik
  ARM: dts: msm: Add cnss-enable-self-recovery flag for shima
  ARM: dts: msm: Update memory-map for sdxlemur
  ARM: dts: qcom: add physical addr for swr tx slaves of Shima
  ARM: dts: msm: Update PSCI state id for shima
  ARM: dts: msm: Update the PSCI mode id for yupik
  ARM: dts: qcom: Add quiet-therm thermal zone mitigation for HOLI
  ARM: dts: msm: Add AOP QMP nodes for yupik
  ARM: dts: msm: Add glink entries for yupik
  ARM: dts: msm: Add HWSPINLOCK, SMEM and SMP2P for yupik
  dt-bindings: thermal: Add support for QMI beamer ADC and RF sensors
  ARM: dts: qcom: Fix watchdog entry for sdxlemur
  ARM: dts: msm: Update GPU, core isolation and hotplug threshold for SHIMA
  ARM: dts: msm: Enable LCD_REG_EN gpio and LCD_BKLT_PWM on shima
  bindings: pinctrl: Add device-tree bindings for SDNIGHTJAR pinctrl driver
  ARM: dts: msm: Move firmware node ahead
  ARM: dts: msm: Change IPA bandwidth threshold value for holi target
  ARM: dts: msm: add USB3_DP_COM_TYPEC_STATUS register
  ARM: dts: msm: Add rmtfs_sharedmem support for sdxlemur
  ARM: dts: msm: Add panel information to amoled-ecm for Shima platforms
  ARM: dts: msm: update PLL_BIAS_CONTROL_2 for holi QRD
  ARM: dts: msm: add display message queue to trusted vm for lahaina
  ARM: dts: msm: Configure L9B from retention mode to LPM on shima
  ARM: dts: msm: Add cnss config for internal power amp for shima
  ARM: dts: msm: Update the qmp register macro file name for Lahaina
  ARM: dts: msm: Add QMP PHY dt entries on sdxlemur
  ARM: dts: msm: Export qfprom cell to userspace for Shima
  ARM: dts: msm: Add beamer ADC and RF sensors for HOLI
  ARM: dts: msm: Add firmware node for yupik
  ARM: dts: msm: Add cdsp rpmsg entry in holi and shima
  ARM: dts: msm: Add GPU_CPR register space for Shima
  ARM: dts: msm: Add RDPM register map for Lahaina GPU
  ARM: dts: msm: Add SD card regulator devices for sdxlemur
  ARM: dts: msm: Convert sdxlemur stub regulators to RPMh
  ARM: dts: msm: remove low voltage VCC support entry from DT
  ARM: dts: msm: Add cqhci_ice and sdcc_ice_slave regions
  ARM: dts: msm: Add hw gcc reset for sdcc on holi
  ARM: dts: msm: add WL_EN entry in BT node
  ARM: dts: msm: Add hw gcc reset support for eMMC on shima
  ARM: dts: msm: Change the node location for optimise
  ARM: dts: msm: Update UFS VCC regulator min voltage for shima
  ARM: dts: msm: Add scuba-iot files on 5.4
  ARM: dts: msm: add audio routings sdxlemur
  ARM: dts: msm: Export qfprom cell to userspace
  dt-bindings: Add qfprom-sys documentation
  ARM: dts: msm: Fix command DB address for sdxlemur
  ARM: dts: msm: update ddr mapping table for shima target
  ARM: dts: msm: Update S3A min and init voltages for holi
  ARM: dts: msm: Update CNSS node for BT GPIO config for shima
  dt-bindings: media: Add video driver bindings for Yupik
  ARM: dts: msm: Add focaltech touch support on holi cdp
  ARM: dts: msm: disable mem-offline node
  ARM: dts: msm: Add handles for USB3 interface clocks
  ARM: dts: msm: Add touch support for holi
  ARM: dts: msm: Add lcd display support on holi
  ARM: dts: msm: Update S3A min and init voltages for holi
  ARM: dts: msm: Add USB nodes for Yupik
  ARM: dts: msm: Add idle states and stats devices for yupik
  ARM: dts: msm: Add PDC and RSC devices for yupik
  ARM: dts: msm: Enable board specific USB detection on sdxlemur
  ARM: dts: msm: Add interconnect entries for USB on sdxlemur
  ARM: dts: msm: Add tlmm pinctrl support for SA8195
  ARM: dts: msm: Add initial device tree for SA8195
  ARM: dts: msm: Remove CDP DT for SA8155
  bindings: Documentation: add SDK audio properties
  ARM: dts: msm: update sound card name for holi usbc variant
  ARM: dts: msm: Disable fastmap for IPA CBs on SDXLEMUR
  ARM: dts: msm: Remove bi_tcxo_ao clock and vdd_cx_ao handles from GCC
  ARM: dts: msm: Add Bus voting support
  bindings: leds: vibrator: Move vibrator LDO documentation to correct folder
  ARM: dts: msm: Added pil nodes for sdxlemur
  ARM: dts: msm: Add ufs dt node for yupik
  ARM: dts: msm: Add board device-tree files for SDXLEMUR target
  ARM: dts: msm: Enable smmu for shima ufs
  ARM: dts: qcom: Change L4P's max output voltage
  ARM: dts: msm: Change to auto-specific config for SA8155
  ARM: dts: msm: Enable smcinvoke and shmbridge on shima
  ARM: dts: msm: Add IMEM entry for Yupik
  ARM: dts: msm: Enable qcom,vmid-cp-camera-preview-ro on Shima
  ARM: dts: qcom: add physical addr for swr tx slaves
  ARM: dts: msm: Add new DT entry for wan agg pkt size
  ARM: dts: msm: Add touch support for Command Mode on holi
  ARM: dts: msm: Add handles for USB3 interface clocks
  ARM: dts: msm: Add ipa_hw support for SDXLEMUR
  ARM: dts: msm: remove cpu7 llcc-ddr lat device node
  ARM: dts: msm: Add focaltech touch support on holi cdp
  ARM: dts: msm: add WL_EN entry in BT node
  ARM: dts: msm: Add debugcc and APSSCC clock nodes for sdxlemur
  ARM: dts: msm: Update CNSS node for BT GPIO config
  dt-bindings: thermal: Add support for modem skin sensor via QMI
  dt-bindings: thermal: Add support for bandwidth cooling devices
  ARM: dts: msm: update modem qmi sennor list for SHIMA
  ARM: dts: msm: Update modem mitigation threshold for lahaina
  ARM: dts: msm: Select 120Hz panel as default on 120Hz shima dts
  ARM: dts: msm: Vote for DDR BW for MPSS PIL on Lahaina
  ARM: dts: msm: Add wireless-fw-name property for Shima platforms
  ARM: dts: msm: Add psci and scm nodes for Yupik
  dt-bindings: spi_qsd: Add documentation of SPI BLSP driver
  ARM: dts: qcom: enable display on trusted vm for shima
  ARM: dts: msm: Add BLSP DTSI nodes on sdxlemur
  ARM: dts: msm: Enable U1 and U2 on Holi
  dt-bindings: i2c-msm-v2: Add snapshot of I2C MSM V2 driver
  dt-bindings: qcom-sps-dma: Add snapshot of SPS DMA driver
  dt-bindings: Add DT bindings for BLSP UART drivers
  ARM: dts: qcom: Update cp channel names for holi
  ARM: dts: msm: Add Qpic Nand support for sdxlemur
  ARM: dts: msm: Correct name of funnel merg on holi
  ARM: dts: msm: add is-always-on flag to fix HS LPI issue for holi
  ARM: dts: msm: New touch node for Lahaina CDP
  ARM: dts: msm: Disable wakeup capability for soundwire gpio
  ARM: dts: msm: Update core isolation and hotplug threshold for lahaina
  ARM: dts: msm: Add emergency skin rule for lahaina
  ARM: dts: msm: Add modem mitigation for policy engine in lahaina
  ARM: dts: msm: Update focaltech enteries on lahaina qrd trustedvm
  ARM: dts: msm: Update focaltech enteries on shima trustedvm
  ARM: dts: msm: Add 144 fps touch support on shima target
  ARM: dts: msm: reserved memory for yupik
  ARM: dts: msm: add initial support for hw memlat devices
  ARM: dts: msm: Add touch support for holi
  ARM: dts: msm: enable lt9611uxc for hdk8350
  ARM: dts: msm: add stub interconnect devices for YUPIK
  ARM: dts: msm: Remove interconnect phandles from clock nodes
  ARM: dts: msm: Update L12C min and init voltage on shima
  ARM: dts: msm: Add lcd display support on holi
  ARM: dts: msm: add touch for Holi 90hz panel
  ARM: dts: msm: Update USB3 DP QMP Phy sequence for Lahaina to v1.10
  ARM: dts: msm: Change prng dtsi config from 32 bit to 64 bits
  ARM: dts: msm: Enable USB AHB reset on sdxlemur Rumi
  dt-bindings: input: touchscren: add description for synaptics_dsx
  ARM: dts: msm: Add device tree for Shima IDP/IDPS with 120fps platform
  ARM: dts: msm: remove deprecated PCIe AUX CLK frequency for lahaina
  dt-bindings: arm: msm: update documentation for PCIe internal AUX CLK
  dt-bindings: interconnect: add interconnect bindings
  ARM: dts: msm: Add cnss-enable-self-recovery flag for lahaina
  ARM: dts: msm: switch off kpti on holi
  ARM: dts: msm: Update cnss dt node for holi
  ARM: dts: msm: new vdd power rail of USB QMP PHY for lahaina-v2
  ARM: dts: qcom: disable panic on single corruption
  ARM: dts: msm: Add PCIe0 PHY settings v1.01 for sdxlemur
  ARM: dts: msm: Extend pmic dump size for holi
  ARM: dts: msm: Enable 747MHz GPU Fmax for Shima
  ARM: dts: msm: define new sound card for holi wcd938x with aatc variant
  ARM: dts: msm: Add entry for non secure display heap memory
  ARM: dts: msm: Add dummy clock nodes for clock controllers for YUPIK
  ARM: dts: msm: Add ADC channels and thermal zones to sdxlemur
  ARM: dts: msm: Remove PM7250B from sdxlemur pmic overlay
  ARM: dts: msm: Add pmesg reserved memory for holi
  ARM: dts: msm: add touch for Holi 90hz panel
  Revert "ARM: dts: msm: Add GPU SMMU clocks for holi"
  ARM: dts: msm: Configure WLAN smmu node in atomic context
  ARM: dts: msm: add mclk lpi gpio entry to all wsa881x entries
  ARM: dts: qcom: Optimize jeita-fcc-step thresholds
  dt-bindings: Add snapshot of batterydata devicetree bindings
  ARM: dts: msm: Add WLED support on PM6150l for holi.
  ARM: dts: msm: Enable ep delay for holi.
  ARM: dts: msm: update low SVS clock corner for holi.
  ARM: dts: msm: Add dpdm supply for PM7250b for holi.
  bindings: clock: rpmcc: Add clk handoff property.
  ARM: dts: msm: correction to adsp variant read entry.
  Revert "arm: msm: dts: Disable rimps access till rimps brought up"
  ARM: dts: msm: fix to indetify proper adsp variant
  ARM: dts: msm: Enable smmu s1 from wlan side
  ARM: dts: msm: Add gpu speed bin property for holi
  ARM: dts: msm: Add gpu gaming bin support for holi
  ARM: dts: msm: Update wlan configuration for holi
  ARM: dts: msm: Enable SMMU S1 for USB on Holi
  ARM: dts: msm: Enable SMMU S1 for AP on Holi
  ARM: dts: msm: enable dcc on holi
  ARM: dts: msm: dtsi changes for holi
  ARM: dts: msm: Add command mode touch support on holi
  ARM: dts: msm: Add notification edge for glink ssr
  ARM: dts: msm: correct the audio etm name
  ARM: dts: msm: Define console before other QUP devices
  ARM: dts: msm: disable wcss cti on holi
  ARM: dts: msm: Add support for SCM PAS for holi
  ARM: dts: qcom: add support for backlight cooling device on Holi
  ARM: dts: msm: Add touchscreen device node for QRD holi
  ARM: dts: msm: add display support for qrd holi
  ARM: dts: qcom: Add camera dts into holi QRD
  arm: msm: dts: Disable rimps access till rimps brought up

Change-Id: I0bcc39a848fce9e17051c31e591032cea18ba020

arch/arm64/boot/dts/vendor/bindings/arm/msm/subsystem-sleep-stats.yaml

@@ -23,9 +23,15 @@ properties:
    Value type: <string>
    Definition: Should be "qcom,subsystem-sleep-stats".
 
+  reg:
+    maxItems: 1
+
+required:
+  - compatible
 
 example:
   - |
     subsystem-sleep-stats {
 		compatible = "qcom,subsystem-sleep-stats";
+		reg = <0xc3f0000 0 0x400>;
 	};

arch/arm64/boot/dts/vendor/bindings/cnss/cnss-wlan.txt

@@ -92,6 +92,7 @@ Optional properties:
 		regulator used in internal power amplifier for QCA6490
   - cnss-enable-self-recovery: Boolean property to enable self recovery when
                                recovery is trigeered with reason link down.
+  - default_gen_speed: U32 property to specify pcie default gen speed.
   - qcom,bt-en-gpio: QCA6490 requires synchronization for BT and WLAN GPIO
 		enable to resolve PMU power up issues. Provide BT GPIO using
 		this config param.

arch/arm64/boot/dts/vendor/bindings/gpu/adreno.txt

@@ -8,6 +8,7 @@ Required properties:
 			Must include "qcom,adreno-gpu-a619-holi" for Holi target.
 			Must include "qcom,adreno-gpu-a642" for Shima target.
 			Must include "qcom,adreno-gpu-a642l" for Yupik target.
+			Must include "qcom,adreno-gpu-a643" for Yupik a643 target.
 - reg:			Specifies the list of register regions for the device.
 - reg-names:		Resource names used for the register regions specified
 			in reg.

arch/arm64/boot/dts/vendor/bindings/input/qpnp-power-on.txt

@@ -129,6 +129,8 @@ Optional properties:
 - qcom,use-legacy-hard-reset-offset       Boolean property to support legacy
 				hard-reset offset of the PON_RB_SPARE register for
 				some (PON gen2) platforms.
+- qcom,log-kpd-event:		Boolean property to enable logging of KPDPWR status
+				during driver INIT and runtime when key is pressed.
 
 Optional Sub-nodes:
 - qcom,pon_1 ... qcom,pon_n:	These PON child nodes correspond to features

arch/arm64/boot/dts/vendor/bindings/pci/msm_ep_pcie.txt

@@ -75,6 +75,8 @@ Optional Properties:
 	- qcom,msm-bus,vectors-KBps
   - qcom,pcie-m2-autonomous: Enable L1ss sleep/exit to support M2 autonomous mode.
   - qcom,mhi-soc-reset-offset: AXI register offset to initiate a SOC reset.
+  - qcom,avoid-reboot-in-d3hot: Ensures device is not in D3hot during
+    reboot/panic.
 
 Example:
 

arch/arm64/boot/dts/vendor/bindings/power/reset/qcom,dload-mode.yaml

@@ -16,6 +16,18 @@ properties:
   compatible:
     items:
       - const: qcom,dload-mode
+  reg:
+    Value type: <prop-encoded-array>
+    Definition: The base address and size for reading the proper configuration
+                related information.
+
+  reg-names:
+    Value type: string
+    Definition: The reg name for reading the configurations.
+
+  qcom,boot-config-shift:
+    Value type: <prop-encoded-array>
+    Definition: The range of bits from low to high.
 
 required:
   - compatible

arch/arm64/boot/dts/vendor/bindings/sound/qcom-audio-dev.txt

@@ -1444,8 +1444,10 @@ Example:
 				"msm-pcm-routing", "msm-cpe-lsm",
 				"msm-compr-dsp", "msm-pcm-dsp-noirq";
 		asoc-cpu = <&dai_hdmi>, <&dai_dp>,
-				<&dai_mi2s0>, <&dai_mi2s1>,
-				<&dai_mi2s2>, <&dai_mi2s3>,
+				<&dai_mi2s0_rx>, <&dai_mi2s0_tx>,
+				<&dai_mi2s1_rx>, <&dai_mi2s1_tx>,
+				<&dai_mi2s2_rx>, <&dai_mi2s2_tx>,
+				<&dai_mi2s3_rx>, <&dai_mi2s3_tx>,
 				<&dai_pri_auxpcm>, <&dai_sec_auxpcm>,
 				<&dai_tert_auxpcm>, <&dai_quat_auxpcm>,
 				<&sb_0_rx>, <&sb_0_tx>, <&sb_1_rx>, <&sb_1_tx>,
@@ -1468,6 +1470,8 @@ Example:
 		asoc-cpu-names = "msm-dai-q6-hdmi.8",  "msm-dai-q6-dp.24608",
 				"msm-dai-q6-mi2s.0", "msm-dai-q6-mi2s.1",
 				"msm-dai-q6-mi2s.2", "msm-dai-q6-mi2s.3",
+				"msm-dai-q6-mi2s.4", "msm-dai-q6-mi2s.5",
+				"msm-dai-q6-mi2s.6", "msm-dai-q6-mi2s.7",
 				"msm-dai-q6-auxpcm.1", "msm-dai-q6-auxpcm.2",
 				"msm-dai-q6-auxpcm.3", "msm-dai-q6-auxpcm.4",
 				"msm-dai-q6-dev.16384", "msm-dai-q6-dev.16385",
@@ -1578,9 +1582,12 @@ Example:
 				"msm-pcm-routing", "msm-compr-dsp",
 				"msm-pcm-dsp-noirq";
 		asoc-cpu = <&dai_dp>,
-				<&dai_mi2s0>, <&dai_mi2s1>,
-				<&dai_mi2s2>, <&dai_mi2s3>,
-				<&dai_mi2s4>, <&dai_pri_auxpcm>,
+				<&dai_mi2s0_rx>, <&dai_mi2s0_tx>,
+				<&dai_mi2s1_rx>, <&dai_mi2s1_tx>,
+				<&dai_mi2s2_rx>, <&dai_mi2s2_tx>,
+				<&dai_mi2s3_rx>, <&dai_mi2s3_tx>,
+				<&dai_mi2s4_rx>, <&dai_mi2s4_tx>,
+				<&dai_pri_auxpcm>,
 				<&dai_sec_auxpcm>, <&dai_tert_auxpcm>,
 				<&dai_quat_auxpcm>, <&dai_quin_auxpcm>,
 				<&afe_pcm_rx>, <&afe_pcm_tx>, <&afe_proxy_rx>,
@@ -1608,7 +1615,10 @@ Example:
 		asoc-cpu-names = "msm-dai-q6-dp.24608",
 				"msm-dai-q6-mi2s.0", "msm-dai-q6-mi2s.1",
 				"msm-dai-q6-mi2s.2", "msm-dai-q6-mi2s.3",
-				"msm-dai-q6-mi2s.4", "msm-dai-q6-auxpcm.1",
+				"msm-dai-q6-mi2s.4", "msm-dai-q6-mi2s.5",
+				"msm-dai-q6-mi2s.6", "msm-dai-q6-mi2s.7",
+				"msm-dai-q6-mi2s.8", "msm-dai-q6-mi2s.9",
+				"msm-dai-q6-auxpcm.1",
 				"msm-dai-q6-auxpcm.2", "msm-dai-q6-auxpcm.3",
 				"msm-dai-q6-auxpcm.4", "msm-dai-q6-auxpcm.5",
 				"msm-dai-q6-dev.224",
@@ -1714,9 +1724,12 @@ Example:
 				"msm-pcm-dsp-noirq", "msm-pcm-loopback.1",
 				"msm-pcm-dtmf";
 		asoc-cpu = <&dai_hdmi>, <&dai_dp>,
-				<&dai_mi2s0>, <&dai_mi2s1>,
-				<&dai_mi2s2>, <&dai_mi2s3>,
-				<&dai_mi2s4>, <&dai_pri_auxpcm>,
+				<&dai_mi2s0_rx>, <&dai_mi2s0_tx>,
+				<&dai_mi2s1_rx>, <&dai_mi2s1_tx>,
+				<&dai_mi2s2_rx>, <&dai_mi2s2_tx>,
+				<&dai_mi2s3_rx>, <&dai_mi2s3_tx>,
+				<&dai_mi2s4_rx>, <&dai_mi2s4_tx>,
+				<&dai_pri_auxpcm>,
 				<&dai_sec_auxpcm>, <&dai_tert_auxpcm>,
 				<&dai_quat_auxpcm>, <&dai_quin_auxpcm>,
 				<&afe_pcm_rx>, <&afe_pcm_tx>, <&afe_proxy_rx>,
@@ -1748,7 +1761,10 @@ Example:
 		asoc-cpu-names = "msm-dai-q6-hdmi.8",  "msm-dai-q6-dp.24608",
 				"msm-dai-q6-mi2s.0", "msm-dai-q6-mi2s.1",
 				"msm-dai-q6-mi2s.2", "msm-dai-q6-mi2s.3",
-				"msm-dai-q6-mi2s.4", "msm-dai-q6-auxpcm.1",
+				"msm-dai-q6-mi2s.4", "msm-dai-q6-mi2s.5",
+				"msm-dai-q6-mi2s.6", "msm-dai-q6-mi2s.7",
+				"msm-dai-q6-mi2s.8", "msm-dai-q6-mi2s.9",
+				"msm-dai-q6-auxpcm.1",
 				"msm-dai-q6-auxpcm.2", "msm-dai-q6-auxpcm.3",
 				"msm-dai-q6-auxpcm.4", "msm-dai-q6-auxpcm.5",
 				"msm-dai-q6-dev.224", "msm-dai-q6-dev.225",
@@ -1857,9 +1873,12 @@ Example:
 				"msm-pcm-afe", "msm-lsm-client",
 				"msm-pcm-routing", "msm-compr-dsp",
 				"msm-pcm-dsp-noirq";
-		asoc-cpu = <&dai_mi2s0>, <&dai_mi2s1>,
-				<&dai_mi2s2>, <&dai_mi2s3>,
-				<&dai_mi2s4>, <&dai_pri_auxpcm>,
+		asoc-cpu = <&dai_mi2s0_rx>, <&dai_mi2s0_tx>,
+				<&dai_mi2s1_rx>, <&dai_mi2s1_tx>,
+				<&dai_mi2s2_rx>, <&dai_mi2s2_tx>,
+				<&dai_mi2s3_rx>, <&dai_mi2s3_tx>,
+				<&dai_mi2s4_rx>, <&dai_mi2s4_tx>,
+				<&dai_pri_auxpcm>,
 				<&dai_sec_auxpcm>, <&dai_tert_auxpcm>,
 				<&dai_quat_auxpcm>, <&dai_quin_auxpcm>,
 				<&afe_pcm_rx>, <&afe_pcm_tx>, <&afe_proxy_rx>,
@@ -1885,7 +1904,10 @@ Example:
 				<&tx_cdc_dma_6_tx>, <&tx_cdc_dma_7_tx>;
 		asoc-cpu-names = "msm-dai-q6-mi2s.0", "msm-dai-q6-mi2s.1",
 				"msm-dai-q6-mi2s.2", "msm-dai-q6-mi2s.3",
-				"msm-dai-q6-mi2s.4", "msm-dai-q6-auxpcm.1",
+				"msm-dai-q6-mi2s.4", "msm-dai-q6-mi2s.5",
+				"msm-dai-q6-mi2s.6", "msm-dai-q6-mi2s.7",
+				"msm-dai-q6-mi2s.8", "msm-dai-q6-mi2s.9",
+				"msm-dai-q6-auxpcm.1",
 				"msm-dai-q6-auxpcm.2", "msm-dai-q6-auxpcm.3",
 				"msm-dai-q6-auxpcm.4", "msm-dai-q6-auxpcm.5",
 				"msm-dai-q6-dev.224",
@@ -2147,9 +2169,12 @@ Example:
 				"msm-pcm-routing", "msm-compr-dsp",
 				"msm-pcm-dsp-noirq";
 		asoc-cpu = <&dai_dp>,
-				<&dai_mi2s0>, <&dai_mi2s1>,
-				<&dai_mi2s2>, <&dai_mi2s3>,
-				<&dai_mi2s4>, <&dai_pri_auxpcm>,
+				<&dai_mi2s0_rx>, <&dai_mi2s0_rx>,
+				<&dai_mi2s1_rx>, <&dai_mi2s1_tx>,
+				<&dai_mi2s2_rx>, <&dai_mi2s2_tx>,
+				<&dai_mi2s3_rx>, <&dai_mi2s3_tx>,
+				<&dai_mi2s4_rx>, <&dai_mi2s4_tx>,
+				<&dai_pri_auxpcm>,
 				<&dai_sec_auxpcm>, <&dai_tert_auxpcm>,
 				<&dai_quat_auxpcm>, <&dai_quin_auxpcm>,
 				<&afe_pcm_rx>, <&afe_pcm_tx>, <&afe_proxy_rx>,
@@ -2176,7 +2201,10 @@ Example:
 		asoc-cpu-names = "msm-dai-q6-dp.24608",
 				"msm-dai-q6-mi2s.0", "msm-dai-q6-mi2s.1",
 				"msm-dai-q6-mi2s.2", "msm-dai-q6-mi2s.3",
-				"msm-dai-q6-mi2s.4", "msm-dai-q6-auxpcm.1",
+				"msm-dai-q6-mi2s.4", "msm-dai-q6-mi2s.5",
+				"msm-dai-q6-mi2s.6", "msm-dai-q6-mi2s.7",
+				"msm-dai-q6-mi2s.8", "msm-dai-q6-mi2s.9",
+				"msm-dai-q6-auxpcm.1",
 				"msm-dai-q6-auxpcm.2", "msm-dai-q6-auxpcm.3",
 				"msm-dai-q6-auxpcm.4", "msm-dai-q6-auxpcm.5",
 				"msm-dai-q6-dev.224",
@@ -2300,9 +2328,12 @@ Example:
 				"msm-pcm-dsp-noirq", "msm-pcm-loopback.1",
 				"msm-pcm-dtmf";
 		asoc-cpu = <&dai_hdmi>, <&dai_dp>,
-				<&dai_mi2s0>, <&dai_mi2s1>,
-				<&dai_mi2s2>, <&dai_mi2s3>,
-				<&dai_mi2s4>, <&dai_pri_auxpcm>,
+				<&dai_mi2s0_rx>, <&dai_mi2s0_rx>,
+				<&dai_mi2s1_rx>, <&dai_mi2s1_tx>,
+				<&dai_mi2s2_rx>, <&dai_mi2s2_tx>,
+				<&dai_mi2s3_rx>, <&dai_mi2s3_tx>,
+				<&dai_mi2s4_rx>, <&dai_mi2s4_tx>,
+				<&dai_pri_auxpcm>,
 				<&dai_sec_auxpcm>, <&dai_tert_auxpcm>,
 				<&dai_quat_auxpcm>, <&dai_quin_auxpcm>,
 				<&afe_pcm_rx>, <&afe_pcm_tx>, <&afe_proxy_rx>,
@@ -2334,7 +2365,10 @@ Example:
 		asoc-cpu-names = "msm-dai-q6-hdmi.8",  "msm-dai-q6-dp.24608",
 				"msm-dai-q6-mi2s.0", "msm-dai-q6-mi2s.1",
 				"msm-dai-q6-mi2s.2", "msm-dai-q6-mi2s.3",
-				"msm-dai-q6-mi2s.4", "msm-dai-q6-auxpcm.1",
+				"msm-dai-q6-mi2s.4", "msm-dai-q6-mi2s.5",
+				"msm-dai-q6-mi2s.6", "msm-dai-q6-mi2s.7",
+				"msm-dai-q6-mi2s.8", "msm-dai-q6-mi2s.9",
+				"msm-dai-q6-auxpcm.1",
 				"msm-dai-q6-auxpcm.2", "msm-dai-q6-auxpcm.3",
 				"msm-dai-q6-auxpcm.4", "msm-dai-q6-auxpcm.5",
 				"msm-dai-q6-dev.224", "msm-dai-q6-dev.225",
@@ -2444,9 +2478,13 @@ Example:
 				"msm-pcm-routing", "msm-compr-dsp",
 				"msm-pcm-dsp-noirq";
 		asoc-cpu = <&dai_dp>, <&dai_dp1>,
-				<&dai_mi2s0>, <&dai_mi2s1>,
-				<&dai_mi2s2>, <&dai_mi2s3>,
-				<&dai_mi2s4>, <&dai_mi2s5>, <&dai_pri_auxpcm>,
+				<&dai_mi2s0_rx>, <&dai_mi2s0_tx>,
+				<&dai_mi2s1_rx>, <&dai_mi2s1_tx>,
+				<&dai_mi2s2_rx>, <&dai_mi2s2_tx>,
+				<&dai_mi2s3_rx>, <&dai_mi2s3_tx>,
+				<&dai_mi2s4_rx>, <&dai_mi2s4_tx>,
+				<&dai_mi2s5_rx>, <&dai_mi2s5_tx>,
+				<&dai_pri_auxpcm>,
 				<&dai_sec_auxpcm>, <&dai_tert_auxpcm>,
 				<&dai_quat_auxpcm>, <&dai_quin_auxpcm>,
 				<&dai_sen_auxpcm>,
@@ -2479,6 +2517,9 @@ Example:
 				"msm-dai-q6-mi2s.0", "msm-dai-q6-mi2s.1",
 				"msm-dai-q6-mi2s.2", "msm-dai-q6-mi2s.3",
 				"msm-dai-q6-mi2s.4", "msm-dai-q6-mi2s.5",
+				"msm-dai-q6-mi2s.6", "msm-dai-q6-mi2s.7",
+				"msm-dai-q6-mi2s.8", "msm-dai-q6-mi2s.9",
+				"msm-dai-q6-mi2s.10", "msm-dai-q6-mi2s.11",
 				"msm-dai-q6-auxpcm.1",
 				"msm-dai-q6-auxpcm.2", "msm-dai-q6-auxpcm.3",
 				"msm-dai-q6-auxpcm.4", "msm-dai-q6-auxpcm.5",
@@ -2595,8 +2636,10 @@ Example:
 				"msm-pcm-afe", "msm-lsm-client",
 				"msm-pcm-routing", "msm-compr-dsp",
 				"msm-pcm-dsp-noirq";
-		asoc-cpu = <&dai_mi2s0>, <&dai_mi2s1>,
-				<&dai_mi2s2>, <&dai_mi2s3>,
+		asoc-cpu = <&dai_mi2s0_rx>, <&dai_mi2s0_tx>,
+				<&dai_mi2s1_rx>, <&dai_mi2s1_tx>,
+				<&dai_mi2s2_rx>, <&dai_mi2s2_tx>,
+				<&dai_mi2s3_rx>, <&dai_mi2s3_tx>,
 				<&dai_pri_auxpcm>,
 				<&dai_sec_auxpcm>, <&dai_tert_auxpcm>,
 				<&dai_quat_auxpcm>,
@@ -2623,6 +2666,8 @@ Example:
 				<&rx_cdc_dma_7_rx>,<&afe_loopback_tx>;
 		asoc-cpu-names = "msm-dai-q6-mi2s.0", "msm-dai-q6-mi2s.1",
 				"msm-dai-q6-mi2s.2", "msm-dai-q6-mi2s.3",
+				"msm-dai-q6-mi2s.4", "msm-dai-q6-mi2s.5",
+				"msm-dai-q6-mi2s.6", "msm-dai-q6-mi2s.7",
 				"msm-dai-q6-auxpcm.1",
 				"msm-dai-q6-auxpcm.2", "msm-dai-q6-auxpcm.3",
 				"msm-dai-q6-auxpcm.4",
@@ -2802,9 +2847,12 @@ Example:
 				"msm-pcm-dsp-noirq", "msm-pcm-loopback.1",
 				"msm-pcm-dtmf";
 		asoc-cpu = <&dai_hdmi>, <&dai_dp>,
-				<&dai_mi2s0>, <&dai_mi2s1>,
-				<&dai_mi2s2>, <&dai_mi2s3>,
-				<&dai_mi2s4>, <&dai_pri_auxpcm>,
+				<&dai_mi2s0_rx>, <&dai_mi2s0_tx>,
+				<&dai_mi2s1_rx>, <&dai_mi2s1_tx>,
+				<&dai_mi2s2_rx>, <&dai_mi2s2_tx>,
+				<&dai_mi2s3_rx>, <&dai_mi2s3_tx>,
+				<&dai_mi2s4_rx>, <&dai_mi2s4_tx>,
+				<&dai_pri_auxpcm>,
 				<&dai_sec_auxpcm>, <&dai_tert_auxpcm>,
 				<&dai_quat_auxpcm>, <&dai_quin_auxpcm>,
 				<&afe_pcm_rx>, <&afe_pcm_tx>, <&afe_proxy_rx>,
@@ -2836,7 +2884,10 @@ Example:
 		asoc-cpu-names = "msm-dai-q6-hdmi.8",  "msm-dai-q6-dp.24608",
 				"msm-dai-q6-mi2s.0", "msm-dai-q6-mi2s.1",
 				"msm-dai-q6-mi2s.2", "msm-dai-q6-mi2s.3",
-				"msm-dai-q6-mi2s.4", "msm-dai-q6-auxpcm.1",
+				"msm-dai-q6-mi2s.4", "msm-dai-q6-mi2s.5",
+				"msm-dai-q6-mi2s.6", "msm-dai-q6-mi2s.7",
+				"msm-dai-q6-mi2s.8", "msm-dai-q6-mi2s.9",
+				"msm-dai-q6-auxpcm.1",
 				"msm-dai-q6-auxpcm.2", "msm-dai-q6-auxpcm.3",
 				"msm-dai-q6-auxpcm.4", "msm-dai-q6-auxpcm.5",
 				"msm-dai-q6-dev.224", "msm-dai-q6-dev.225",

arch/arm64/boot/dts/vendor/bindings/thermal/qcom,devfreq-vdd-cdev.txt

@@ -0,0 +1,34 @@
+Qualcomm Technologies, Inc. Devfreq Vdd cooling device
+
+The Devfreq Vdd cooling device, will be used to set minimum
+operating level for gfx rail using gpu devfreq interface
+during cold thermal condition. This cooling device will be
+used with cold temp monitor thermal zone. Whenever cold
+temperature triggers, it disables frequencies lower than
+the minimum operating level using devfreq opp API's.
+
+Required Parameters:
+- compatible:
+	Usage: required
+	Value type: <string>
+	Definition: should be "qcom,devfreq-vdd-cooling-device"
+
+- devfreq:
+	Usage: required
+	Value type: <devfreq phandle>
+	Definition: Phandle to the GPU devfreq. This will register the GPU
+		devfreq as a cooling device with thermal framework.
+
+- #cooling-cells:
+	Usage: required
+	Value type: <integer>
+	Definition: Must be 2. This is required by of-thermal and refer the doc
+		<devicetree/bindings/thermal/thermal.txt> for more details.
+
+Example:
+
+	devfreq_vdd_cdev: devfreq-vdd-cdev {
+		compatible = "qcom,devfreq-vdd-cooling-device";
+		devfreq = <&msm_gpu>;
+		#cooling-cells = <2>;
+	};

arch/arm64/boot/dts/vendor/bindings/thermal/qti-qmi-cdev.txt

@@ -73,6 +73,29 @@ Subsystem properties:
 						device,
 			"pa_dsc" -> DSC based pa cooling device,
 			"pa_fr1_dsc" -> DSC based pa cooling device.
+			"modem_lte_dsc" -> DSC based modem lte cooling device,
+			"modem_nr_dsc" -> DSC based modem nr cooling device,
+			"modem_nr_scg_dsc" -> DSC based modem nr scg cooling
+						device,
+			"sdr0_lte_dsc" -> DSC based sdr0 lte cooling device,
+			"sdr1_lte_dsc" -> DSC based sdr1 lte cooling device,
+			"sdr0_nr_dsc" -> DSC based sdr0 nr cooling device,
+			"sdr1_nr_dsc" -> DSC based sdr1 nr cooling device,
+			"pa_lte_sdr0_dsc" -> DSC based pa lte sdr0 cooling
+						device,
+			"pa_lte_sdr1_dsc" -> DSC based pa lte sdr1 cooling
+						device,
+			"pa_nr_sdr0_dsc" -> DSC based pa nr sdr0 cooling device,
+			"pa_nr_sdr1_dsc" -> DSC based pa nr sdr1 cooling device,
+			"pa_nr_sdr0_scg_dsc" -> DSC based pa nr sdr0 scg cooling
+						device,
+			"pa_nr_sdr1_scg_dsc" -> DSC based pa nr sdr1 scg cooling
+						device,
+			"mmw0_dsc" -> DSC based MMW cooling device0,
+			"mmw1_dsc" -> DSC based MMW cooling device1,
+			"mmw2_dsc" -> DSC based MMW cooling device2,
+			"mmw3_dsc" -> DSC based MMW cooling device3,
+			"mmw_ific_dsc" -> DSC based MMW IFIC cooling device.
 
 	-#cooling-cells:
 		Usage: required

arch/arm64/boot/dts/vendor/bindings/usb/qcom,dwc3.txt

@@ -46,6 +46,10 @@ Optional properties:
 - qcom,select-utmi-as-pipe-clk: if present, disable USB3 pipe_clk requirement.
 				Used when dwc3 operates without SSPHY and only
 				HS/FS/LS modes are supported.
+- qcom,iommu-best-fit-algo:	If present, enables best fit algorithm for iova
+				allocation. This helps in reducing fragmentation
+				and utilizing the iova address space more
+				efficiently.
 
 Required child node:
 A child node must exist to represent the core DWC3 IP block. The name of

arch/arm64/boot/dts/vendor/qcom/Makefile

@@ -213,12 +213,16 @@ dtbo-$(CONFIG_ARCH_YUPIK) +=    \
 	yupikp-idps-amoled-overlay.dtbo \
 	yupikp-idp-hsp-overlay.dtbo \
 	yupik-iot-idp-overlay.dtbo \
+	yupik-iot-idp-pm7250b-overlay.dtbo \
 	yupik-iot-qrd-overlay.dtbo \
 	yupik-iot-hsp-overlay.dtbo \
+	yupik-iot-hsp-pm7250b-overlay.dtbo \
 	yupik-iot-idps-amoled-overlay.dtbo \
 	yupikp-iot-idp-overlay.dtbo \
+	yupikp-iot-idp-pm7250b-overlay.dtbo \
 	yupikp-iot-qrd-overlay.dtbo \
 	yupikp-iot-hsp-overlay.dtbo \
+	yupikp-iot-hsp-pm7250b-overlay.dtbo \
 	yupikp-iot-idps-amoled-overlay.dtbo
 
 
@@ -235,12 +239,16 @@ yupikp-qrd-overlay.dtbo-base := yupikp.dtb
 yupikp-idps-amoled-overlay.dtbo-base := yupikp.dtb
 yupikp-idp-hsp-overlay.dtbo-base := yupikp-hsp.dtb
 yupik-iot-idp-overlay.dtbo-base := yupik-iot.dtb
+yupik-iot-idp-pm7250b-overlay.dtbo-base := yupik-iot.dtb
 yupik-iot-qrd-overlay.dtbo-base := yupik-iot.dtb
 yupik-iot-hsp-overlay.dtbo-base := yupik-iot.dtb
+yupik-iot-hsp-pm7250b-overlay.dtbo-base := yupik-iot.dtb
 yupik-iot-idps-amoled-overlay.dtbo-base := yupik-iot.dtb
 yupikp-iot-idp-overlay.dtbo-base := yupikp-iot.dtb
+yupikp-iot-idp-pm7250b-overlay.dtbo-base := yupikp-iot.dtb
 yupikp-iot-qrd-overlay.dtbo-base := yupikp-iot.dtb
 yupikp-iot-hsp-overlay.dtbo-base := yupikp-iot.dtb
+yupikp-iot-hsp-pm7250b-overlay.dtbo-base := yupikp-iot.dtb
 yupikp-iot-idps-amoled-overlay.dtbo-base := yupikp-iot.dtb
 else
 dtb-$(CONFIG_ARCH_YUPIK) += yupik-rumi.dtb \
@@ -256,12 +264,16 @@ dtb-$(CONFIG_ARCH_YUPIK) += yupik-rumi.dtb \
 	yupikp-idps-amoled.dtb \
 	yupikp-idp-hsp.dtb \
 	yupik-iot-idp.dtb \
+	yupik-iot-idp-pm7250b.dtb \
 	yupik-iot-qrd.dtb \
 	yupik-iot-hsp.dtb \
 	yupik-iot-idps-amoled.dtb \
 	yupikp-iot-idp.dtb \
+	yupikp-iot-idp-pm7250b.dtb \
 	yupikp-iot-qrd.dtb \
 	yupikp-iot-hsp.dtb \
+	yupik-iot-hsp-pm7250b.dtb \
+	yupikp-iot-hsp-pm7250b.dtb \
 	yupikp-iot-idps-amoled.dtb
 endif
 
@@ -433,7 +445,17 @@ dtb-$(CONFIG_ARCH_SDXLEMUR) += sdxlemur-rumi.dtb \
 	sdxlemur-v2-mtp-mbb-pcie-ep-ipq.dtb \
 	sdxlemur-v2-mtp-mbb-pcie-rc-ep.dtb \
 	sdxlemur-v2-rcm-pcie-ep.dtb \
-	sdxlemur-v2-rcm-rc.dtb
+	sdxlemur-v2-rcm-rc.dtb \
+	sdxlemur-v2-atp.dtb \
+	sdxlemur-v2-mtp-cpe-pine1x.dtb \
+	sdxlemur-v2-mtp-cpe-pine2x.dtb \
+	sdxlemur-v2-mtp-mbb-emmc-512mb.dtb \
+	sdxlemur-v2-mtp-mbb-m2-ep-usb.dtb \
+	sdxlemur-v2-mtp-mbb-m2-ep.dtb \
+	sdxlemur-v2-rcm-rc-pine1x.dtb \
+	sdxlemur-v2-rcm-rc-pine2x.dtb \
+	sdxlemur-v2-m2-ep-fwa.dtb
+
 
 
 ifeq ($(CONFIG_ARCH_SHIMA), y)

arch/arm64/boot/dts/vendor/qcom/blair-atp.dtsi

@@ -347,10 +347,6 @@
 		regulator-s3-level-ao {
 			status = "okay";
 		};
-
-		gfx-cdev {
-			status = "okay";
-		};
 	};
 
 	/* Enable mx_cdev for PM6350 */

arch/arm64/boot/dts/vendor/qcom/blair-cdp.dtsi

@@ -261,7 +261,7 @@
 	#address-cells = <1>;
 	#size-cells = <0>;
 	status = "okay";
-	qcom,i2c-touch-active="synaptics,tcm-i2c";
+	qcom,i2c-touch-active= "synaptics,tcm-i2c";
 
 	synaptics_tcm@20 {
 		compatible = "synaptics,tcm-i2c";
@@ -309,6 +309,9 @@
 		pinctrl-0 = <&ts_active>;
 		pinctrl-1 = <&ts_int_suspend &ts_reset_suspend>;
 		pinctrl-2 = <&pmx_ts_release>;
+
+		panel = <&dsi_r66451_amoled_cmd
+			&dsi_r66451_amoled_video>;
 	};
 
 	novatek@62 {

arch/arm64/boot/dts/vendor/qcom/blair-pinctrl.dtsi

@@ -337,7 +337,7 @@
 			qupv3_se7_i2c_active: qupv3_se7_i2c_active {
 				mux {
 					pins = "gpio27", "gpio28";
-					function = "qup11";
+					function = "qup11_f1";
 				};
 
 				config {

arch/arm64/boot/dts/vendor/qcom/blair.dtsi

@@ -63,6 +63,7 @@
 			device_type = "cpu";
 			compatible = "qcom,kryo";
 			reg = <0x0 0x0>;
+			cpu-idle-states = <&SLVR_PC &SLVR_RAIL_OFF>;
 			enable-method = "psci";
 			capacity-dmips-mhz = <1024>;
 			dynamic-power-coefficient = <100>;
@@ -86,6 +87,7 @@
 			device_type = "cpu";
 			compatible = "qcom,kryo";
 			reg = <0x0 0x100>;
+			cpu-idle-states = <&SLVR_PC &SLVR_RAIL_OFF>;
 			enable-method = "psci";
 			capacity-dmips-mhz = <1024>;
 			dynamic-power-coefficient = <100>;
@@ -103,6 +105,7 @@
 			device_type = "cpu";
 			compatible = "qcom,kryo";
 			reg = <0x0 0x200>;
+			cpu-idle-states = <&SLVR_PC &SLVR_RAIL_OFF>;
 			enable-method = "psci";
 			capacity-dmips-mhz = <1024>;
 			dynamic-power-coefficient = <100>;
@@ -120,6 +123,7 @@
 			device_type = "cpu";
 			compatible = "qcom,kryo";
 			reg = <0x0 0x300>;
+			cpu-idle-states = <&SLVR_PC &SLVR_RAIL_OFF>;
 			enable-method = "psci";
 			capacity-dmips-mhz = <1024>;
 			dynamic-power-coefficient = <100>;
@@ -138,6 +142,7 @@
 			compatible = "qcom,kryo";
 			reg = <0x0 0x400>;
 			enable-method = "psci";
+			cpu-idle-states = <&SLVR_PC &SLVR_RAIL_OFF>;
 			capacity-dmips-mhz = <1024>;
 			dynamic-power-coefficient = <100>;
 			cpu-release-addr = <0x0 0x50000000>;
@@ -155,6 +160,7 @@
 			compatible = "qcom,kryo";
 			reg = <0x0 0x500>;
 			enable-method = "psci";
+			cpu-idle-states = <&SLVR_PC &SLVR_RAIL_OFF>;
 			capacity-dmips-mhz = <1024>;
 			dynamic-power-coefficient = <100>;
 			cpu-release-addr = <0x0 0x50000000>;
@@ -171,6 +177,7 @@
 			device_type = "cpu";
 			compatible = "qcom,kryo";
 			reg = <0x0 0x600>;
+			cpu-idle-states = <&GOLD_PC &GOLD_RAIL_OFF>;
 			enable-method = "psci";
 			capacity-dmips-mhz = <1946>;
 			dynamic-power-coefficient = <520>;
@@ -189,6 +196,7 @@
 			device_type = "cpu";
 			compatible = "qcom,kryo";
 			reg = <0x0 0x700>;
+			cpu-idle-states = <&GOLD_PC &GOLD_RAIL_OFF>;
 			enable-method = "psci";
 			capacity-dmips-mhz = <1946>;
 			dynamic-power-coefficient = <520>;

arch/arm64/boot/dts/vendor/qcom/direwolf-vm-audio.dtsi

@@ -1089,9 +1089,12 @@
 				"msm-pcm-dsp-noirq", "msm-pcm-loopback.1",
 				"msm-pcm-dtmf";
 		asoc-cpu = <&dai_hdmi>, <&dai_dp>,
-				<&dai_mi2s0>, <&dai_mi2s1>,
-				<&dai_mi2s2>, <&dai_mi2s3>,
-				<&dai_mi2s4>, <&dai_pri_auxpcm>,
+				<&dai_mi2s0_rx>, <&dai_mi2s0_tx>,
+				<&dai_mi2s1_rx>, <&dai_mi2s1_tx>,
+				<&dai_mi2s2_rx>, <&dai_mi2s2_tx>,
+				<&dai_mi2s3_rx>, <&dai_mi2s3_tx>,
+				<&dai_mi2s4_rx>, <&dai_mi2s4_tx>,
+				<&dai_pri_auxpcm>,
 				<&dai_sec_auxpcm>, <&dai_tert_auxpcm>,
 				<&dai_quat_auxpcm>, <&dai_quin_auxpcm>,
 				<&afe_pcm_rx>, <&afe_pcm_tx>,
@@ -1167,7 +1170,10 @@
 		asoc-cpu-names = "msm-dai-q6-hdmi.8",  "msm-dai-q6-dp.0",
 				"msm-dai-q6-mi2s.0", "msm-dai-q6-mi2s.1",
 				"msm-dai-q6-mi2s.2", "msm-dai-q6-mi2s.3",
-				"msm-dai-q6-mi2s.4", "msm-dai-q6-auxpcm.1",
+				"msm-dai-q6-mi2s.4", "msm-dai-q6-mi2s.5",
+				"msm-dai-q6-mi2s.6", "msm-dai-q6-mi2s.7",
+				"msm-dai-q6-mi2s.8", "msm-dai-q6-mi2s.9",
+				"msm-dai-q6-auxpcm.1",
 				"msm-dai-q6-auxpcm.2", "msm-dai-q6-auxpcm.3",
 				"msm-dai-q6-auxpcm.4", "msm-dai-q6-auxpcm.5",
 				"msm-dai-q6-dev.224", "msm-dai-q6-dev.225",

arch/arm64/boot/dts/vendor/qcom/holi-audio.dtsi

@@ -34,7 +34,7 @@
 					      <0x00008000>, <0x00009000>,
 					      <0x0000A000>, <0x0000B000>,
 					      <0x0000C000>, <0x0000D000>,
-					      <0x0000E000>, <0x0000F0000>,
+					      <0x0000E000>, <0x0000F000>,
 					      <0x00010000>, <0x00011000>,
 					      <0x00012000>;
 			qcom,lpi-slew-offset-tbl = <0x00000000>, <0x00000002>,
@@ -153,8 +153,10 @@
 				"msm-pcm-afe", "msm-lsm-client",
 				"msm-pcm-routing", "msm-compr-dsp",
 				"msm-pcm-dsp-noirq";
-		asoc-cpu = <&dai_mi2s0>, <&dai_mi2s1>,
-				<&dai_mi2s2>, <&dai_mi2s3>,
+		asoc-cpu = <&dai_mi2s0_rx>, <&dai_mi2s0_tx>,
+				<&dai_mi2s1_rx>, <&dai_mi2s1_tx>,
+				<&dai_mi2s2_rx>, <&dai_mi2s2_tx>,
+				<&dai_mi2s3_rx>, <&dai_mi2s3_tx>,
 				<&dai_pri_auxpcm>,
 				<&dai_sec_auxpcm>, <&dai_tert_auxpcm>,
 				<&dai_quat_auxpcm>,
@@ -181,6 +183,8 @@
 				<&rx_cdc_dma_7_rx>,<&afe_loopback_tx>;
 		asoc-cpu-names = "msm-dai-q6-mi2s.0", "msm-dai-q6-mi2s.1",
 				"msm-dai-q6-mi2s.2", "msm-dai-q6-mi2s.3",
+				"msm-dai-q6-mi2s.4", "msm-dai-q6-mi2s.5",
+				"msm-dai-q6-mi2s.6", "msm-dai-q6-mi2s.7",
 				"msm-dai-q6-auxpcm.1",
 				"msm-dai-q6-auxpcm.2", "msm-dai-q6-auxpcm.3",
 				"msm-dai-q6-auxpcm.4",

arch/arm64/boot/dts/vendor/qcom/holi-pmic-overlay-pm6125.dtsi

@@ -494,3 +494,6 @@
 	};
 };
 
+&pm6125_pon {
+	qcom,log-kpd-event;
+};

arch/arm64/boot/dts/vendor/qcom/holi-regulators-pm6125.dtsi

@@ -74,10 +74,6 @@
 		regulator-s3-level-ao {
 			status = "disabled";
 		};
-
-		gfx-cdev {
-			status = "disabled";
-		};
 	};
 
 	/* Disable mx_cdev for PM6150A */
@@ -434,16 +430,6 @@
 					<RPM_SMD_REGULATOR_LEVEL_BINNING>;
 			qcom,use-voltage-level;
 		};
-
-		gfx_cdev: gfx-cdev {
-			status = "okay";
-			compatible = "qcom,regulator-cooling-device";
-			regulator-cdev-supply = <&S8A_LEVEL_AO>;
-			regulator-levels = <RPM_SMD_REGULATOR_LEVEL_NONE
-					RPM_SMD_REGULATOR_LEVEL_SVS_PLUS>;
-			#cooling-cells = <2>;
-		};
-
 	};
 
 	/* VDD_LPI_CX supply */

arch/arm64/boot/dts/vendor/qcom/holi-regulators-pm6350.dtsi

@@ -50,14 +50,6 @@
 					<RPM_SMD_REGULATOR_LEVEL_BINNING>;
 			qcom,use-voltage-level;
 		};
-
-		gfx_cdev: gfx-cdev {
-			compatible = "qcom,regulator-cooling-device";
-			regulator-cdev-supply = <&S3A_LEVEL_AO>;
-			regulator-levels = <RPM_SMD_REGULATOR_LEVEL_RETENTION
-					RPM_SMD_REGULATOR_LEVEL_SVS_PLUS>;
-			#cooling-cells = <2>;
-		};
 	};
 
 	/* PM6350 L1 - VDD_MX supply */

arch/arm64/boot/dts/vendor/qcom/holi-thermal.dtsi

@@ -72,6 +72,12 @@
 		#cooling-cells = <2>;
 		status = "disabled";
 	};
+
+	devfreq_vdd_cdev: devfreq-vdd-cdev {
+		compatible = "qcom,devfreq-vdd-cooling-device";
+		devfreq = <&msm_gpu>;
+		#cooling-cells = <2>;
+	};
 };
 
 &rpm_bus {
@@ -1167,9 +1173,9 @@
 				cooling-device = <&mx_cdev 1 1>;
 			};
 
-			gfx_vdd_cdev {
+			devfreq_vdd_cdev {
 				trip = <&zeroc_0_trip>;
-				cooling-device = <&gfx_cdev 1 1>;
+				cooling-device = <&devfreq_vdd_cdev 2 2>;
 			};
 
 			adsp_vdd_cdev {
@@ -1214,9 +1220,9 @@
 				cooling-device = <&mx_cdev 1 1>;
 			};
 
-			gfx_vdd_cdev {
+			devfreq_vdd_cdev {
 				trip = <&zeroc_1_trip>;
-				cooling-device = <&gfx_cdev 1 1>;
+				cooling-device = <&devfreq_vdd_cdev 2 2>;
 			};
 
 			adsp_vdd_cdev {

arch/arm64/boot/dts/vendor/qcom/lahaina-pm.dtsi

@@ -130,6 +130,11 @@
 		reg = <0xb221200 0x60>;
 	};
 
+	subsystem-sleep-stats {
+		compatible = "qcom,subsystem-sleep-stats";
+		reg = <0xc3f0000 0x400>;
+	};
+
 	soc-sleep-stats@c3f0000 {
 		compatible = "qcom,rpmh-sleep-stats";
 		reg = <0xc3f0000 0x400>;

arch/arm64/boot/dts/vendor/qcom/lahaina.dtsi

@@ -4665,6 +4665,7 @@
 		qcom,ipa-holb-monitor-max-cnt-11ad = <10>;
 		qcom,tx-wrapper-cache-max-size = <400>;
 		qcom,ipa-gpi-event-rp-ddr;
+		qcom,register-collection-on-crash;
 		clock-names = "core_clk";
 		clocks = <&clock_rpmh RPMH_IPA_CLK>;
 		qcom,interconnect,num-cases = <5>;

arch/arm64/boot/dts/vendor/qcom/pm6125.dtsi

@@ -17,7 +17,7 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 
-		qcom,power-on@800 {
+		pm6125_pon: qcom,power-on@800 {
 			compatible = "qcom,qpnp-power-on";
 			reg = <0x800>;
 			interrupts = <0x0 0x8 0x0 IRQ_TYPE_EDGE_BOTH>,

arch/arm64/boot/dts/vendor/qcom/sa6155-audio.dtsi

@@ -517,9 +517,12 @@ qcom,msm-dai-q6 {
 				"msm-pcm-dsp-noirq", "msm-pcm-loopback.1",
 				"msm-pcm-dtmf";
 		asoc-cpu = <&dai_hdmi>, <&dai_dp>,
-				<&dai_mi2s0>, <&dai_mi2s1>,
-				<&dai_mi2s2>, <&dai_mi2s3>,
-				<&dai_mi2s4>, <&dai_pri_auxpcm>,
+				<&dai_mi2s0_rx>, <&dai_mi2s0_tx>,
+				<&dai_mi2s1_rx>, <&dai_mi2s1_tx>,
+				<&dai_mi2s2_rx>, <&dai_mi2s2_tx>,
+				<&dai_mi2s3_rx>, <&dai_mi2s3_tx>,
+				<&dai_mi2s4_rx>, <&dai_mi2s4_tx>,
+				<&dai_pri_auxpcm>,
 				<&dai_sec_auxpcm>, <&dai_tert_auxpcm>,
 				<&dai_quat_auxpcm>, <&dai_quin_auxpcm>,
 				<&afe_pcm_rx>, <&afe_pcm_tx>,
@@ -553,9 +556,11 @@ qcom,msm-dai-q6 {
 				<&dai_quin_tdm_tx_2>, <&dai_quin_tdm_tx_3>,
 				<&dai_quin_tdm_tx_7>;
 		asoc-cpu-names = "msm-dai-q6-hdmi.8",  "msm-dai-q6-dp.0",
-				"msm-dai-q6-mi2s.0", "msm-dai-q6-mi2s.1",
-				"msm-dai-q6-mi2s.2", "msm-dai-q6-mi2s.3",
-				"msm-dai-q6-mi2s.4", "msm-dai-q6-auxpcm.1",
+				"msm-dai-q6-mi2s.1", "msm-dai-q6-mi2s.2",
+				"msm-dai-q6-mi2s.3", "msm-dai-q6-mi2s.4",
+				"msm-dai-q6-mi2s.5", "msm-dai-q6-mi2s.6",
+				"msm-dai-q6-mi2s.7", "msm-dai-q6-mi2s.8",
+				"msm-dai-q6-mi2s.9", "msm-dai-q6-auxpcm.1",
 				"msm-dai-q6-auxpcm.2", "msm-dai-q6-auxpcm.3",
 				"msm-dai-q6-auxpcm.4", "msm-dai-q6-auxpcm.5",
 				"msm-dai-q6-dev.224", "msm-dai-q6-dev.225",

arch/arm64/boot/dts/vendor/qcom/sa8155-audio.dtsi

@@ -513,9 +513,12 @@ qcom,msm-dai-q6 {
 				"msm-pcm-dsp-noirq", "msm-pcm-loopback.1",
 				"msm-pcm-dtmf";
 		asoc-cpu = <&dai_hdmi>, <&dai_dp>,
-				<&dai_mi2s0>, <&dai_mi2s1>,
-				<&dai_mi2s2>, <&dai_mi2s3>,
-				<&dai_mi2s4>, <&dai_pri_auxpcm>,
+				<&dai_mi2s0_rx>, <&dai_mi2s0_tx>,
+				<&dai_mi2s1_rx>, <&dai_mi2s1_tx>,
+				<&dai_mi2s2_rx>, <&dai_mi2s2_tx>,
+				<&dai_mi2s3_rx>, <&dai_mi2s3_tx>,
+				<&dai_mi2s4_rx>, <&dai_mi2s4_tx>,
+				<&dai_pri_auxpcm>,
 				<&dai_sec_auxpcm>, <&dai_tert_auxpcm>,
 				<&dai_quat_auxpcm>, <&dai_quin_auxpcm>,
 				<&afe_pcm_rx>, <&afe_pcm_tx>,
@@ -549,9 +552,11 @@ qcom,msm-dai-q6 {
 				<&dai_quin_tdm_tx_2>, <&dai_quin_tdm_tx_3>,
 				<&dai_quin_tdm_tx_7>;
 		asoc-cpu-names = "msm-dai-q6-hdmi.8",  "msm-dai-q6-dp.0",
-				"msm-dai-q6-mi2s.0", "msm-dai-q6-mi2s.1",
-				"msm-dai-q6-mi2s.2", "msm-dai-q6-mi2s.3",
-				"msm-dai-q6-mi2s.4", "msm-dai-q6-auxpcm.1",
+				"msm-dai-q6-mi2s.1", "msm-dai-q6-mi2s.2",
+				"msm-dai-q6-mi2s.3", "msm-dai-q6-mi2s.4",
+				"msm-dai-q6-mi2s.5", "msm-dai-q6-mi2s.6",
+				"msm-dai-q6-mi2s.7", "msm-dai-q6-mi2s.8",
+				"msm-dai-q6-mi2s.9", "msm-dai-q6-auxpcm.1",
 				"msm-dai-q6-auxpcm.2", "msm-dai-q6-auxpcm.3",
 				"msm-dai-q6-auxpcm.4", "msm-dai-q6-auxpcm.5",
 				"msm-dai-q6-dev.224", "msm-dai-q6-dev.225",

arch/arm64/boot/dts/vendor/qcom/sa8155-vm-audio.dtsi

@@ -469,9 +469,12 @@
 				"msm-pcm-dsp-noirq", "msm-pcm-loopback.1",
 				"msm-pcm-dtmf";
 		asoc-cpu = <&dai_hdmi>, <&dai_dp>,
-				<&dai_mi2s0>, <&dai_mi2s1>,
-				<&dai_mi2s2>, <&dai_mi2s3>,
-				<&dai_mi2s4>, <&dai_pri_auxpcm>,
+				<&dai_mi2s0_rx>, <&dai_mi2s0_tx>,
+				<&dai_mi2s1_rx>, <&dai_mi2s1_tx>,
+				<&dai_mi2s2_rx>, <&dai_mi2s2_tx>,
+				<&dai_mi2s3_rx>, <&dai_mi2s3_tx>,
+				<&dai_mi2s4_rx>, <&dai_mi2s4_tx>,
+				<&dai_pri_auxpcm>,
 				<&dai_sec_auxpcm>, <&dai_tert_auxpcm>,
 				<&dai_quat_auxpcm>, <&dai_quin_auxpcm>,
 				<&afe_pcm_rx>, <&afe_pcm_tx>,
@@ -505,9 +508,11 @@
 				<&dai_quin_tdm_tx_2>, <&dai_quin_tdm_tx_3>,
 				<&dai_quin_tdm_tx_7>;
 		asoc-cpu-names = "msm-dai-q6-hdmi.8",  "msm-dai-q6-dp.0",
-				"msm-dai-q6-mi2s.0", "msm-dai-q6-mi2s.1",
-				"msm-dai-q6-mi2s.2", "msm-dai-q6-mi2s.3",
-				"msm-dai-q6-mi2s.4", "msm-dai-q6-auxpcm.1",
+				"msm-dai-q6-mi2s.1", "msm-dai-q6-mi2s.2",
+				"msm-dai-q6-mi2s.3", "msm-dai-q6-mi2s.4",
+				"msm-dai-q6-mi2s.5", "msm-dai-q6-mi2s.6",
+				"msm-dai-q6-mi2s.7", "msm-dai-q6-mi2s.8",
+				"msm-dai-q6-mi2s.9", "msm-dai-q6-auxpcm.1",
 				"msm-dai-q6-auxpcm.2", "msm-dai-q6-auxpcm.3",
 				"msm-dai-q6-auxpcm.4", "msm-dai-q6-auxpcm.5",
 				"msm-dai-q6-dev.224", "msm-dai-q6-dev.225",

arch/arm64/boot/dts/vendor/qcom/scuba-audio.dtsi

@@ -100,8 +100,10 @@
 				"msm-pcm-afe", "msm-lsm-client",
 				"msm-pcm-routing", "msm-compr-dsp",
 				"msm-pcm-dsp-noirq";
-		asoc-cpu = <&dai_mi2s0>, <&dai_mi2s1>,
-				<&dai_mi2s2>, <&dai_mi2s3>,
+		asoc-cpu = <&dai_mi2s0_rx>, <&dai_mi2s0_tx>,
+				<&dai_mi2s1_rx>, <&dai_mi2s1_tx>,
+				<&dai_mi2s2_rx>, <&dai_mi2s2_tx>,
+				<&dai_mi2s3_rx>, <&dai_mi2s3_tx>,
 				<&dai_pri_auxpcm>,
 				<&dai_sec_auxpcm>, <&dai_tert_auxpcm>,
 				<&dai_quat_auxpcm>,
@@ -128,6 +130,8 @@
 				<&afe_loopback_tx>;
 		asoc-cpu-names = "msm-dai-q6-mi2s.0", "msm-dai-q6-mi2s.1",
 				"msm-dai-q6-mi2s.2", "msm-dai-q6-mi2s.3",
+				"msm-dai-q6-mi2s.4", "msm-dai-q6-mi2s.5",
+				"msm-dai-q6-mi2s.6", "msm-dai-q6-mi2s.7",
 				"msm-dai-q6-auxpcm.1",
 				"msm-dai-q6-auxpcm.2", "msm-dai-q6-auxpcm.3",
 				"msm-dai-q6-auxpcm.4", "msm-dai-q6-dev.224",

arch/arm64/boot/dts/vendor/qcom/sdxlemur-bluetooth.dtsi

@@ -19,7 +19,6 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&bt_en_default>;
 		qcom,bt-reset-gpio = <&pmx65_gpios 15 0>; /* BT_EN */
-		qcom,bt-sw-ctrl-gpio = <&pmx65_gpios 2 0>; /* SW_CTRL */
 
 		clocks = <&rpmhcc RPMH_RF_CLK3>;
 		clock-names = "ref3_clk";

arch/arm64/boot/dts/vendor/qcom/sdxlemur-cnss.dtsi

@@ -30,6 +30,7 @@
 
 		use-pm-domain;
 		cnss-enable-self-recovery;
+		default_gen_speed = <0>;
 
 		vdd-wlan-aon-supply = <&S7B>;
 		qcom,vdd-wlan-aon-config = <1012000 1012000 0 0 0>;
@@ -169,12 +170,7 @@
 			};
 
 			mhi_event@2 {
-				mhi,num-elements = <32>;
-				mhi,intmod = <0>;
-				mhi,msi = <0>;
-				mhi,priority = <2>;
-				mhi,brstmode = <2>;
-				mhi,data-type = <3>;
+				status = "disabled";
 			};
 		};
 

arch/arm64/boot/dts/vendor/qcom/sdxlemur-mtp-cpe-hsp.dtsi

@@ -14,28 +14,3 @@
 		#size-cells = <1>;
 	};
 };
-
-&wlan {
-	mhi_events {
-		mhi_event@0 {
-			mhi,num-elements = <32>;
-			mhi,intmod = <0>;
-			mhi,msi = <1>;
-			mhi,priority = <0>;
-			mhi,brstmode = <2>;
-			mhi,data-type = <1>;
-		};
-
-		mhi_event@1 {
-			mhi,num-elements = <256>;
-			mhi,intmod = <0>;
-			mhi,msi = <2>;
-			mhi,priority = <1>;
-			mhi,brstmode = <2>;
-		};
-
-		mhi_event@2 {
-			status = "disabled";
-		};
-	};
-};

arch/arm64/boot/dts/vendor/qcom/sdxlemur-mtp-cpe-pine1x.dts

@@ -4,6 +4,7 @@
 #include "sdxlemur-mtp-cpe.dtsi"
 #include "sdxlemur-mtp-cpe-pine1x.dtsi"
 #include "sdxlemur-1024mb.dtsi"
+#include "sdxlemur-bluetooth.dtsi"
 
 / {
 	model = "Qualcomm Technologies, Inc. SDXLEMUR MTP CPE 1x Pine";

arch/arm64/boot/dts/vendor/qcom/sdxlemur-mtp-cpe-pine1x.dtsi

@@ -13,7 +13,7 @@
 	};
 };
 
-&ntn3_vreg {
+&qps615_vreg {
 	vin-supply = <&pine_vreg>;
 };
 
@@ -29,7 +29,7 @@
 		reg = <0 0 0 0 0>;
 		qcom,iommu-group = <&qcn9000_pci_iommu_group_0>;
 		memory-region = <&qcn9000_0_mem>;
-		qrtr_instance_id = <0x0>;
+		qrtr_instance_id = <0x20>;
 
 		#address-cells = <1>;
 		#size-cells = <1>;

arch/arm64/boot/dts/vendor/qcom/sdxlemur-mtp-cpe-pine2x.dts

@@ -4,6 +4,7 @@
 #include "sdxlemur-mtp-cpe.dtsi"
 #include "sdxlemur-mtp-cpe-pine2x.dtsi"
 #include "sdxlemur-1024mb.dtsi"
+#include "sdxlemur-bluetooth.dtsi"
 
 / {
 	model = "Qualcomm Technologies, Inc. SDXLEMUR MTP CPE 2x Pine";

arch/arm64/boot/dts/vendor/qcom/sdxlemur-mtp-cpe-pine2x.dtsi

@@ -1,4 +1,82 @@
+#include "sdxlemur-qcn9000.dtsi"
 
 &soc {
-
+	pine_vreg: pine_vreg {
+		compatible = "regulator-fixed";
+		regulator-name = "pine_vreg";
+		gpio = <&tlmm 102 GPIO_ACTIVE_HIGH>;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		enable-active-high;
+		regulator-enable-ramp-delay = <200000>;
+	};
+};
+
+&qps615_vreg {
+	vin-supply = <&pine_vreg>;
+};
+
+&pcie_i2c_ctrl {
+	reg_update = <0x82c030 0x1
+			0x828000 0x3
+			0x82bd00 0x8
+			0x82c030 0x2
+			0x828000 0x3
+			0x82bd00 0x8
+			0x82c030 0x8
+			0x828000 0x1
+			0x82bd00 0x8
+			0x82c01c 0x10
+			0x82c030 0xf
+			0x828000 0xf
+			0x82b268 0x2>;
+};
+
+&pcie0 {
+	qcom,no-l0s-supported;
+	qcom,no-l1-supported;
+	qcom,no-l1ss-supported;
+	qcom,no-aux-clk-sync;
+};
+
+&pcie0_bus2_dev1_fn0 {
+	cnss_pci1: cnss_pci1 {
+		reg = <0 0 0 0 0>;
+		qcom,iommu-group = <&qcn9000_pci_iommu_group_0>;
+		memory-region = <&qcn9000_0_mem>;
+		qrtr_instance_id = <0x20>;
+
+		#address-cells = <1>;
+		#size-cells = <1>;
+	};
+};
+
+&pcie0_bus2_dev2_fn0 {
+	cnss_pci2: cnss_pci2 {
+		reg = <0 0 0 0 0>;
+		qcom,iommu-group = <&qcn9000_pci_iommu_group_1>;
+		memory-region = <&qcn9000_1_mem>;
+		qrtr_instance_id = <0x21>;
+
+		#address-cells = <1>;
+		#size-cells = <1>;
+	};
+};
+
+&wifi0 {
+	status = "ok"
+	board_id = <0xa0>;
+};
+
+&wifi1 {
+	status = "ok"
+	board_id = <0xa1>;
+};
+
+&qcn9000_0_mem {
+	status = "ok"
+};
+
+&qcn9000_1_mem {
+	status = "ok"
 };

arch/arm64/boot/dts/vendor/qcom/sdxlemur-mtp-cpe.dts

@@ -6,6 +6,7 @@
 #include "sdxlemur-1024mb-cpe.dtsi"
 #include "sdxlemur-audio.dtsi"
 #include "sdxlemur-mtp-audio-overlay.dtsi"
+#include "sdxlemur-bluetooth.dtsi"
 
 / {
 	model = "Qualcomm Technologies, Inc. SDXLEMUR MTP CPE";

arch/arm64/boot/dts/vendor/qcom/sdxlemur-mtp-cpe.dtsi

@@ -1,9 +1,9 @@
 #include "sdxlemur-mtp.dtsi"
 
 &soc {
-	ntn3_vreg: ntn3_vreg {
+	qps615_vreg: qps615_vreg {
 		compatible = "regulator-fixed";
-		regulator-name = "ntn3_vreg";
+		regulator-name = "qps615_vreg";
 		gpio = <&tlmm 107 GPIO_ACTIVE_HIGH>;
 		regulator-min-microvolt = <1000000>;
 		regulator-max-microvolt = <1000000>;
@@ -15,29 +15,29 @@
 		compatible = "regulator-fixed";
 		regulator-name = "qca_vreg";
 		gpio = <&tlmm 106 GPIO_ACTIVE_HIGH>;
-		vin-supply = <&ntn3_vreg>;
+		vin-supply = <&qps615_vreg>;
 		regulator-min-microvolt = <1800000>;
 		regulator-max-microvolt = <1800000>;
 		enable-active-high;
-		regulator-enable-ramp-delay = <200000>;
+		regulator-enable-ramp-delay = <80000>;
 	};
 
 	aqr_vreg: aqr_vreg {
 		compatible = "regulator-fixed";
 		regulator-name = "aqr_vreg";
 		gpio = <&tlmm 105 GPIO_ACTIVE_HIGH>;
-		vin-supply = <&qca_vreg>;
+		vin-supply = <&qps615_vreg>;
 		regulator-min-microvolt = <1000000>;
 		regulator-max-microvolt = <1000000>;
 		enable-active-high;
-		regulator-enable-ramp-delay = <2400>;
+		regulator-enable-ramp-delay = <10000>;
 	};
 
-	ioss_qps615_rx: qps615_rx@eth {
+	ioss_aqr_rx: qps615_rx@eth0 {
 		qcom,dir-rx;
 		qcom,rx-filter-ip;
 
-		qcom,ring-size = <128>;
+		qcom,ring-size = <1023>;
 		qcom,buff-size = <2048>;
 
 		qcom,mod-count-min = <64>;
@@ -46,9 +46,9 @@
 		qcom,mod-usecs-max = <60>;
 	};
 
-	ioss_qps615_tx: qps615_tx@eth {
+	ioss_aqr_tx: qps615_tx@eth0 {
 		qcom,dir-tx;
-		qcom,ring-size = <512>;
+		qcom,ring-size = <1023>;
 		qcom,buff-size = <2048>;
 
 		qcom,mod-count-min = <64>;
@@ -57,22 +57,28 @@
 		qcom,mod-usecs-max = <60>;
 	};
 
-	ioss_qps615_eth0: qps615@eth0 {
-		qcom,name = "eth0";
-		qcom,ioss_instance = <0>;
+	ioss_napa_rx: qps615_rx@eth1 {
+		qcom,dir-rx;
+		qcom,rx-filter-ip;
 
-		qcom,ioss_channels =
-			<&ioss_qps615_rx>,
-			<&ioss_qps615_tx>;
+		qcom,ring-size = <127>;
+		qcom,buff-size = <2048>;
+
+		qcom,mod-count-min = <64>;
+		qcom,mod-count-max = <64>;
+		qcom,mod-usecs-min = <30>;
+		qcom,mod-usecs-max = <60>;
 	};
 
-	ioss_qps615_eth1: qps615@eth1 {
-		qcom,name = "eth1";
-		qcom,ioss_instance = <0>;
+	ioss_napa_tx: qps615_tx@eth1 {
+		qcom,dir-tx;
+		qcom,ring-size = <511>;
+		qcom,buff-size = <2048>;
 
-		qcom,ioss_channels =
-			<&ioss_qps615_rx>,
-			<&ioss_qps615_tx>;
+		qcom,mod-count-min = <64>;
+		qcom,mod-count-max = <64>;
+		qcom,mod-usecs-min = <30>;
+		qcom,mod-usecs-max = <60>;
 	};
 };
 
@@ -84,7 +90,7 @@
 		reg = <0x77>;
 		gpio-config-reg = <0x801208>;
 		ep-reset-reg = <0x801210>;
-		ep-reset-gpio-mask = <0xf>;
+		ep-reset-gpio-mask = <0xc>;
 		dump-regs = <0x801330 0x801350 0x801370>;
 		reg_update = <0x82c030 0x1
 					0x828000 0x3
@@ -94,7 +100,13 @@
 					0x82bd00 0x8
 					0x82c030 0x8
 					0x828000 0x1
-					0x82bd00 0x8>;
+					0x82bd00 0x8
+					0x82c01c 0x10
+					0x82c030 0xf
+					0x828000 0xf
+					0x82b268 0x2
+					0x82C02C 0x4
+					0x8249DC 0x0>;
 	};
 };
 
@@ -102,7 +114,158 @@
 &pcie0 {
 	pcie-i2c-phandle = <&i2c_5>;
 
-	vreg-3p3-supply = <&aqr_vreg>;
+	vreg-3p3-supply = <&qps615_vreg>;
+	qcom,phy-sequence = <0x1240 0x03 0x0
+				0x1010 0x01 0x0
+				0x101c 0x31 0x0
+				0x1020 0x01 0x0
+				0x1024 0xde 0x0
+				0x1028 0x07 0x0
+				0x1030 0x97 0x0
+				0x1034 0x0c 0x0
+				0x1044 0x14 0x0
+				0x1048 0x90 0x0
+				0x1058 0x0f 0x0
+				0x1074 0x06 0x0
+				0x1078 0x06 0x0
+				0x107c 0x16 0x0
+				0x1080 0x16 0x0
+				0x1084 0x36 0x0
+				0x1088 0x36 0x0
+				0x1094 0x08 0x0
+				0x10a4 0x46 0x0
+				0x10a8 0x04 0x0
+				0x10ac 0x0a 0x0
+				0x10b0 0x1a 0x0
+				0x10b4 0x14 0x0
+				0x10b8 0x34 0x0
+				0x10bc 0x82 0x0
+				0x10c4 0xd0 0x0
+				0x10cc 0x55 0x0
+				0x10d0 0x55 0x0
+				0x10d4 0x03 0x0
+				0x10d8 0x55 0x0
+				0x10dc 0x55 0x0
+				0x10e0 0x05 0x0
+				0x110c 0x02 0x0
+				0x1154 0x34 0x0
+				0x1158 0x12 0x0
+				0x115c 0x00 0x0
+				0x1168 0x0a 0x0
+				0x116c 0x04 0x0
+				0x119c 0x88 0x0
+				0x1174 0x60 0x0
+				0x117c 0x06 0x0
+				0x11a0 0x14 0x0
+				0x11a8 0x0f 0x0
+				0x0220 0x16 0x0
+				0x03c0 0x38 0x0
+				0x0a20 0x16 0x0
+				0x0bc0 0x38 0x0
+				0x0364 0xcc 0x0
+				0x0368 0x12 0x0
+				0x036c 0xcc 0x0
+				0x0374 0x4a 0x0
+				0x0378 0x29 0x0
+				0x037c 0xc5 0x0
+				0x0380 0xac 0x0
+				0x0384 0xb6 0x0
+				0x0388 0xc0 0x0
+				0x038c 0x07 0x0
+				0x0390 0xfb 0x0
+				0x0394 0x0d 0x0
+				0x0398 0xc5 0x0
+				0x039c 0xee 0x0
+				0x03a0 0xbf 0x0
+				0x03a4 0xa0 0x0
+				0x03a8 0x81 0x0
+				0x03ac 0xde 0x0
+				0x03b0 0x7f 0x0
+				0x0b64 0xcc 0x0
+				0x0b68 0x12 0x0
+				0x0b6c 0xcc 0x0
+				0x0b74 0x4a 0x0
+				0x0b78 0x29 0x0
+				0x0b7c 0xc5 0x0
+				0x0b80 0xac 0x0
+				0x0b84 0xb6 0x0
+				0x0b88 0xc0 0x0
+				0x0b8c 0x07 0x0
+				0x0b90 0xfb 0x0
+				0x0b94 0x0d 0x0
+				0x0b98 0xc5 0x0
+				0x0b9c 0xee 0x0
+				0x0ba0 0xbf 0x0
+				0x0ba4 0xa0 0x0
+				0x0ba8 0x81 0x0
+				0x0bac 0xde 0x0
+				0x0bb0 0x7f 0x0
+				0x03b4 0x20 0x0
+				0x022c 0x3f 0x0
+				0x0230 0x37 0x0
+				0x0bb4 0x20 0x0
+				0x0a2c 0x3f 0x0
+				0x0a30 0x37 0x0
+				0x0078 0x05 0x0
+				0x007c 0xf6 0x0
+				0x0878 0x05 0x0
+				0x087c 0xf6 0x0
+				0x0290 0x05 0x0
+				0x0a90 0x05 0x0
+				0x03f8 0x1f 0x0
+				0x0400 0x1f 0x0
+				0x0408 0x1f 0x0
+				0x0410 0x1f 0x0
+				0x0418 0x1f 0x0
+				0x0420 0x1f 0x0
+				0x03f4 0x1f 0x0
+				0x03fc 0x1f 0x0
+				0x0404 0x1f 0x0
+				0x0bf8 0x1f 0x0
+				0x0c00 0x1f 0x0
+				0x0c08 0x1f 0x0
+				0x0c10 0x1f 0x0
+				0x0c18 0x1f 0x0
+				0x0c20 0x1f 0x0
+				0x0bf4 0x1f 0x0
+				0x0bfc 0x1f 0x0
+				0x0c04 0x1f 0x0
+				0x0208 0x0c 0x0
+				0x0a08 0x0c 0x0
+				0x020c 0x0a 0x0
+				0x0a0c 0x0a 0x0
+				0x02dc 0x0a 0x0
+				0x0adc 0x0a 0x0
+				0x0308 0x0b 0x0
+				0x0b08 0x0b 0x0
+				0x027c 0x10 0x0
+				0x0a7c 0x10 0x0
+				0x02b4 0x00 0x0
+				0x0ab4 0x00 0x0
+				0x02ec 0x0f 0x0
+				0x0aec 0x0f 0x0
+				0x02c4 0x00 0x0
+				0x02c8 0x1f 0x0
+				0x0ac4 0x00 0x0
+				0x0ac8 0x1f 0x0
+				0x0030 0x1a 0x0
+				0x0034 0x0c 0x0
+				0x0830 0x1a 0x0
+				0x0834 0x0c 0x0
+				0x141c 0xc1 0x0
+				0x1490 0x00 0x0
+				0x13e0 0x16 0x0
+				0x13e4 0x22 0x0
+				0x1508 0x02 0x0
+				0x14a0 0x16 0x0
+				0x1420 0x40 0x0
+				0x1584 0x28 0x0
+				0x1370 0x2e 0x0
+				0x155c 0x2e 0x0
+				0x140c 0x1d 0x0
+				0x1388 0xaa 0x0
+				0x1200 0x00 0x0
+				0x1244 0x03 0x0>;
 
 	iommu-map = <0x0 &apps_smmu 0x0200 0x1>,
 		<0x100 &apps_smmu 0x0201 0x1>,
@@ -143,11 +306,22 @@
 				pinctrl-0 = <&aqr_intn_wol_sig>;
 
 				compatible = "qcom,ioss-v2-device";
+				qcom,phy-rst-gpio = <0>;
 				qcom,ioss = <&ioss>;
-				qcom,ioss_interfaces = <&ioss_qps615_eth0>;
+				qcom,ioss_instance = <0>;
+				qcom,ioss_channels =
+					<&ioss_aqr_rx>,
+					<&ioss_aqr_tx>;
+
+				qcom,ioss-wol-phy;
+
+				interrupts-extended = <&tlmm 103 IRQ_TYPE_EDGE_FALLING>;
+				interrupt-names = "wol_irq";
 
 				/* ipa shares this group */
 				qcom,iommu-group = <&ipa_eth_group1>;
+				phy-supply = <&aqr_vreg>;
+				qcom,phy-rst-delay-us = <221000>;
 
 				#address-cells = <1>;
 				#size-cells = <1>;
@@ -168,11 +342,23 @@
 				pinctrl-0 = <&napa_intn_wol_sig>;
 
 				compatible = "qcom,ioss-v2-device";
+				qcom,phy-rst-gpio = <1>;
 				qcom,ioss = <&ioss>;
-				qcom,ioss_interfaces = <&ioss_qps615_eth1>;
+				qcom,ioss_instance = <1>;
+				qcom,ioss_channels =
+					<&ioss_napa_rx>,
+					<&ioss_napa_tx>;
+
+				qcom,ioss-wol-phy;
+				qcom,ioss-wol-magic;
+
+				interrupts-extended = <&tlmm 81 IRQ_TYPE_EDGE_FALLING>;
+				interrupt-names = "wol_irq";
 
 				/* ipa shares this group */
-				qcom,iommu-group = <&ipa_eth_group1>;
+				qcom,iommu-group = <&ipa_eth_group2>;
+				phy-supply = <&qca_vreg>;
+				qcom,phy-rst-delay-us = <20000>;
 
 				#address-cells = <1>;
 				#size-cells = <1>;

arch/arm64/boot/dts/vendor/qcom/sdxlemur-mtp-mbb-m2-ep.dts

@@ -11,3 +11,7 @@
 		"qcom,sdxlemur", "qcom,mtp";
 	qcom,board-id = <0x8010008 0x308>;
 };
+
+&sdx_ext_ipc {
+	status = "ok"
+};

arch/arm64/boot/dts/vendor/qcom/sdxlemur-mtp-mbb-ntn3-pcie.dtsi

@@ -1,9 +1,9 @@
 #include "sdxlemur-mtp-mbb.dtsi"
 
 &soc {
-	ntn3_vreg: ntn3_vreg {
+	qps615_vreg: qps615_vreg {
 		compatible = "regulator-fixed";
-		regulator-name = "ntn3_vreg";
+		regulator-name = "qps615_vreg";
 		gpio = <&tlmm 107 GPIO_ACTIVE_HIGH>;
 		regulator-min-microvolt = <1000000>;
 		regulator-max-microvolt = <1000000>;
@@ -15,13 +15,36 @@
 		compatible = "regulator-fixed";
 		regulator-name = "aqr_vreg";
 		gpio = <&tlmm 105 GPIO_ACTIVE_HIGH>;
-		vin-supply = <&ntn3_vreg>;
+		vin-supply = <&qps615_vreg>;
 		regulator-min-microvolt = <1000000>;
 		regulator-max-microvolt = <1000000>;
 		enable-active-high;
-		regulator-enable-ramp-delay = <2400>;
+		regulator-enable-ramp-delay = <10000>;
 	};
 
+	ioss_qps615_rx: qps615_rx@eth {
+		qcom,dir-rx;
+		qcom,rx-filter-ip;
+
+		qcom,ring-size = <128>;
+		qcom,buff-size = <2048>;
+
+		qcom,mod-count-min = <64>;
+		qcom,mod-count-max = <64>;
+		qcom,mod-usecs-min = <30>;
+		qcom,mod-usecs-max = <60>;
+	};
+
+	ioss_qps615_tx: qps615_tx@eth {
+		qcom,dir-tx;
+		qcom,ring-size = <512>;
+		qcom,buff-size = <2048>;
+
+		qcom,mod-count-min = <64>;
+		qcom,mod-count-max = <64>;
+		qcom,mod-usecs-min = <30>;
+		qcom,mod-usecs-max = <60>;
+	};
 };
 
 &i2c_3 {
@@ -40,7 +63,7 @@
 
 	qcom,filtered-bdfs = <0x02080000>;
 
-	vreg-3p3-supply = <&aqr_vreg>;
+	vreg-3p3-supply = <&qps615_vreg>;
 
 	iommu-map = <0x0 &apps_smmu 0x0200 0x1>,
 		<0x100 &apps_smmu 0x0201 0x1>,
@@ -72,6 +95,30 @@
 		/* BDF 2.3.0 */
 		pcie0_bus2_dev3_fn0: pcie0_bus2_dev3_fn0 {
 			reg = <0x1800 0x0 0x0 0x0 0x0>;
+			qps615_eth0,qps615_eth0@pcie0_rp {
+				reg = <0x0 0x0 0x0 0x0 0x0>;
+
+				compatible = "qcom,ioss-v2-device";
+				qcom,ioss = <&ioss>;
+				qcom,ioss_instance = <0>;
+				qcom,ioss_channels =
+					<&ioss_qps615_rx>,
+					<&ioss_qps615_tx>;
+
+				/* ipa shares this group */
+				qcom,iommu-group = <&ipa_eth_group1>;
+				phy-supply = <&aqr_vreg>;
+				qcom,phy-rst-delay-us = <221000>;
+
+				interrupts-extended = <&tlmm 103 IRQ_TYPE_EDGE_FALLING>;
+				interrupt-names = "wol_irq";
+
+				pinctrl-names = "default";
+				pinctrl-0 = <&aqr_intn_wol_sig>;
+
+				#address-cells = <1>;
+				#size-cells = <1>;
+			};
 			/* BDF 5.0.0 */
 			pcie0_bus5_dev0_fn0: pcie0_ntn3_eth0 {
 				reg = <0x0 0x0 0x0 0x0 0x0>;
@@ -83,28 +130,3 @@
 		};
 	};
 };
-
-&wlan {
-	mhi_events {
-		mhi_event@0 {
-			mhi,num-elements = <32>;
-			mhi,intmod = <0>;
-			mhi,msi = <1>;
-			mhi,priority = <0>;
-			mhi,brstmode = <2>;
-			mhi,data-type = <1>;
-		};
-
-		mhi_event@1 {
-			mhi,num-elements = <256>;
-			mhi,intmod = <0>;
-			mhi,msi = <2>;
-			mhi,priority = <1>;
-			mhi,brstmode = <2>;
-		};
-
-		mhi_event@2 {
-			status = "disabled";
-		};
-	};
-};

arch/arm64/boot/dts/vendor/qcom/sdxlemur-mtp-mbb-pcie-ep-ipq.dtsi

@@ -14,10 +14,12 @@
 
 &pcie_ep {
 	status = "ok"
+	qcom,pcie-perst-enum;
 };
 
 &mhi_device {
 	status = "ok"
+	qcom,no-m0-timeout;
 };
 
 &mhi_net_device {
@@ -68,6 +70,4 @@
 	qcom,iommu-dma = "bypass";
 };
 
-&sdx_ext_ipc {
-	ipq807x_attach = <1>;
-};
+

arch/arm64/boot/dts/vendor/qcom/sdxlemur-mtp-mbb-pcie-ep.dtsi

@@ -66,4 +66,7 @@
 
 &usb {
 	qcom,iommu-dma = "bypass";
+	dwc3@a600000 {
+		snps,usb2-gadget-lpm-disable;
+	};
 };

arch/arm64/boot/dts/vendor/qcom/sdxlemur-mtp-mbb-pcie-rc-ep.dtsi

@@ -25,15 +25,6 @@
 		qcom,mod-usecs-max = <128>;
 	};
 
-	ioss_aqc_eth0: aqc@eth0 {
-		qcom,name = "eth0";
-		qcom,ioss_instance = <0>;
-
-		qcom,ioss_channels =
-			<&ioss_aqc_eth0_rx>,
-			<&ioss_aqc_eth0_tx>;
-	};
-
 	ioss_r8125_eth0_rx: r8125_rx@eth0 {
 		qcom,dir-rx;
 		qcom,rx-filter-ip;
@@ -57,15 +48,6 @@
 		qcom,mod-usecs-min = <30>;
 		qcom,mod-usecs-max = <60>;
 	};
-
-	ioss_r8125_eth0: r8125@eth0 {
-		qcom,name = "eth0";
-		qcom,ioss_instance = <0>;
-
-		qcom,ioss_channels =
-			<&ioss_r8125_eth0_rx>,
-			<&ioss_r8125_eth0_tx>;
-	};
 };
 
 &pcie0_rp {
@@ -79,8 +61,10 @@
 		qcom,ioss = <&ioss>;
 		/* ipa shares this group with aqc */
 		qcom,iommu-group = <&ipa_eth_group1>;
-		qcom,ioss_interfaces =
-			<&ioss_aqc_eth0>;
+		qcom,ioss_instance = <0>;
+		qcom,ioss_channels =
+			<&ioss_aqc_eth0_rx>,
+			<&ioss_aqc_eth0_tx>;
 
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -117,7 +101,10 @@
 
 		compatible = "qcom,ioss-v2-device";
 		qcom,ioss = <&ioss>;
-		qcom,ioss_interfaces = <&ioss_r8125_eth0>;
+		qcom,ioss_instance = <0>;
+		qcom,ioss_channels =
+			<&ioss_r8125_eth0_rx>,
+			<&ioss_r8125_eth0_tx>;
 
 		/* ipa shares this group with rtl */
 		qcom,iommu-group = <&ipa_eth_group1>;

arch/arm64/boot/dts/vendor/qcom/sdxlemur-pcie.dtsi

@@ -51,7 +51,7 @@
 		vreg-mx-supply = <&VDD_MXA_LEVEL>;
 
 		qcom,vreg-1p8-voltage-level = <1200000 1200000 30000>;
-		qcom,vreg-0p9-voltage-level = <912000 912000 132000>;
+		qcom,vreg-0p9-voltage-level = <912000 880000 132000>;
 		qcom,vreg-cx-voltage-level = <RPMH_REGULATOR_LEVEL_MAX
 						RPMH_REGULATOR_LEVEL_LOW_SVS 0>;
 		qcom,vreg-mx-voltage-level = <RPMH_REGULATOR_LEVEL_MAX
@@ -116,7 +116,7 @@
 		qcom,ep-latency = <10>;
 		qcom,num-parf-testbus-sel = <0xb9>;
 
-		qcom,pcie-phy-ver = <1102>;
+		qcom,pcie-phy-ver = <1108>;
 		qcom,phy-status-offset = <0x1214>;
 		qcom,phy-status-bit = <7>;
 		qcom,phy-power-down-offset = <0x1240>;
@@ -159,7 +159,7 @@
 				0x1168 0x0a 0x0
 				0x116c 0x04 0x0
 				0x119c 0x88 0x0
-				0x1174 0x20 0x0
+				0x1174 0x60 0x0
 				0x117c 0x06 0x0
 				0x11a0 0x14 0x0
 				0x11a8 0x0f 0x0
@@ -266,6 +266,8 @@
 				0x1584 0x28 0x0
 				0x1370 0x2e 0x0
 				0x155c 0x2e 0x0
+				0x140c 0x1d 0x0
+				0x1388 0xaa 0x0
 				0x1200 0x00 0x0
 				0x1244 0x03 0x0>;
 

arch/arm64/boot/dts/vendor/qcom/sdxlemur-qcn9000.dtsi

@@ -24,6 +24,11 @@
 };
 
 &soc {
+	/* If QCN9000 is connected, LPM modes are disabled */
+	qcom,lpm-levels {
+		status = "disabled";
+	};
+
 	wifi0: qcom,cnss-qcn9000@a0000000 {
 		status = "disabled";
 		compatible = "qcom,cnss-qcn9000";
@@ -31,7 +36,7 @@
 		reg-names = "smmu_iova_ipa";
 		memory-region = <&qcn9000_0_mem>;
 		qcom,wlan-ramdump-dynamic = <0x400000>;
-		qrtr_node_id = <0x0>;
+		qrtr_node_id = <0x20>;
 		qca,auto-restart;
 		tgt-mem-mode = <0x1>;
 		board_id = <0xa4>;
@@ -155,7 +160,7 @@
 		reg-names = "smmu_iova_ipa";
 		memory-region = <&qcn9000_1_mem>;
 		qcom,wlan-ramdump-dynamic = <0x400000>;
-		qrtr_node_id = <0x0>;
+		qrtr_node_id = <0x21>;
 		qca,auto-restart;
 		tgt-mem-mode = <0x1>;
 		board_id = <0xa4>;

arch/arm64/boot/dts/vendor/qcom/sdxlemur-rcm-rc.dtsi

@@ -3,7 +3,6 @@
 #include <dt-bindings/iio/qti_power_supply_iio.h>
 #include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
 #include <dt-bindings/spmi/spmi.h>
-#include "sdxlemur-cnss.dtsi"
 
 &pm7250b_clkdiv {
 	clocks = <&rpmhcc RPMH_CXO_CLK>;
@@ -15,6 +14,123 @@
 		qcom,batt-id-range-pct = <15>;
 		#include "qg-batterydata-alium-3600mah.dtsi"
 	};
+
+	ioss_aqc_eth0_rx: aqc_rx@eth0 {
+		qcom,dir-rx;
+		qcom,rx-filter-be;
+
+		qcom,ring-size = <1024>;
+		qcom,buff-size = <2048>;
+
+		qcom,mod-count-min = <15>;
+		qcom,mod-count-max = <25>;
+		qcom,mod-usecs-min = <64>;
+		qcom,mod-usecs-max = <128>;
+	};
+
+	ioss_aqc_eth0_tx: aqc_tx@eth0 {
+		qcom,dir-tx;
+		qcom,ring-size = <1024>;
+		qcom,buff-size = <2048>;
+
+		qcom,mod-count-min = <15>;
+		qcom,mod-count-max = <25>;
+		qcom,mod-usecs-min = <64>;
+		qcom,mod-usecs-max = <128>;
+	};
+
+	ioss_r8125_eth0_rx: r8125_rx@eth0 {
+		qcom,dir-rx;
+		qcom,rx-filter-ip;
+
+		qcom,ring-size = <1023>; /* Cannot be a power of 2 */
+		qcom,buff-size = <2048>;
+
+		qcom,mod-count-min = <32>;
+		qcom,mod-count-max = <64>;
+		qcom,mod-usecs-min = <30>;
+		qcom,mod-usecs-max = <60>;
+	};
+
+	ioss_r8125_eth0_tx: r8125_tx@eth0 {
+		qcom,dir-tx;
+		qcom,ring-size = <1024>;
+		qcom,buff-size = <2048>;
+
+		qcom,mod-count-min = <32>;
+		qcom,mod-count-max = <64>;
+		qcom,mod-usecs-min = <30>;
+		qcom,mod-usecs-max = <60>;
+	};
+};
+
+&pcie0_rp {
+	#address-cells = <5>;
+	#size-cells = <0>;
+
+	aquantia,aqc@pcie0_rp {
+		reg = <0 0 0 0 0>;
+
+		compatible = "qcom,ioss-v2-device";
+		qcom,ioss = <&ioss>;
+		/* ipa shares this group with aqc */
+		qcom,iommu-group = <&ipa_eth_group1>;
+		qcom,ioss_instance = <0>;
+		qcom,ioss_channels =
+			<&ioss_aqc_eth0_rx>,
+			<&ioss_aqc_eth0_tx>;
+
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		pci-ids =
+			"1d6a:0001",
+			"1d6a:d107",
+			"1d6a:07b1",
+			"1d6a:87b1",
+			"1d6a:d108",
+			"1d6a:08b1",
+			"1d6a:88b1",
+			"1d6a:d109",
+			"1d6a:09b1",
+			"1d6a:89b1",
+			"1d6a:d100",
+			"1d6a:00b1",
+			"1d6a:80b1",
+			"1d6a:11b1",
+			"1d6a:91b1",
+			"1d6a:12b1",
+			"1d6a:92b1",
+			"1d6a:00c0",
+			"1d6a:04c0",
+			"1d6a:12c0",
+			"1d6a:14c0",
+			"1d6a:93c0",
+			"1d6a:94c0";
+
+	};
+
+	realtek,rtl8125@pcie0_rp {
+		reg = <0 0 0 0 0>;
+
+		compatible = "qcom,ioss-v2-device";
+		qcom,ioss = <&ioss>;
+		qcom,ioss_instance = <0>;
+		qcom,ioss_channels =
+			<&ioss_r8125_eth0_rx>,
+			<&ioss_r8125_eth0_tx>;
+
+		/* ipa shares this group with rtl */
+		qcom,iommu-group = <&ipa_eth_group1>;
+
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		pci-ids =
+			"10ec:8125",
+			"10ec:3000";
+
+	};
 };
 
 &spmi_debug_bus {
@@ -28,9 +144,9 @@
 };
 
 &pcie0 {
-	qcom,boot-option = <0x1>;
 	qcom,l1-2-th-scale = <2>; /* 1us */
 	qcom,l1-2-th-value = <70>;
+	qcom,target-link-speed = <3>;
 };
 
 &qnand_1 {

arch/arm64/boot/dts/vendor/qcom/sdxlemur-regulators.dtsi

@@ -217,9 +217,9 @@
 		L4B: pmx65_l4: regulator-pmx65-l4 {
 			regulator-name = "pmx65_l4";
 			qcom,set = <RPMH_REGULATOR_SET_ALL>;
-			regulator-min-microvolt = <912000>;
+			regulator-min-microvolt = <880000>;
 			regulator-max-microvolt = <912000>;
-			qcom,init-voltage = <912000>;
+			qcom,init-voltage = <880000>;
 			qcom,init-mode = <RPMH_REGULATOR_MODE_HPM>;
 		};
 	};

arch/arm64/boot/dts/vendor/qcom/sdxlemur-thermal-modem.dtsi

@@ -42,33 +42,33 @@
 				#cooling-cells = <2>;
 			};
 
-			pa_sdr0_dsc: pa_sdr0_dsc {
-				qcom,qmi-dev-name = "pa_sdr0_dsc";
+			pa_lte_sdr0_dsc: pa_lte_sdr0_dsc {
+				qcom,qmi-dev-name = "pa_lte_sdr0_dsc";
 				#cooling-cells = <2>;
 			};
 
-			pa_sdr1_dsc: pa_sdr1_dsc {
-				qcom,qmi-dev-name = "pa_sdr1_dsc";
+			pa_lte_sdr1_dsc: pa_lte_sdr1_dsc {
+				qcom,qmi-dev-name = "pa_lte_sdr1_dsc";
 				#cooling-cells = <2>;
 			};
 
-			pa_fr1_sdr0_dsc: pa_fr1_sdr0_dsc {
-				qcom,qmi-dev-name = "pa_fr1_sdr0_dsc";
+			pa_nr_sdr0_dsc: pa_nr_sdr0_dsc {
+				qcom,qmi-dev-name = "pa_nr_sdr0_dsc";
 				#cooling-cells = <2>;
 			};
 
-			pa_fr1_sdr1_dsc: pa_fr1_sdr1_dsc {
-				qcom,qmi-dev-name = "pa_fr1_sdr1_dsc";
+			pa_nr_sdr1_dsc: pa_nr_sdr1_dsc {
+				qcom,qmi-dev-name = "pa_nr_sdr1_dsc";
 				#cooling-cells = <2>;
 			};
 
-			pa_fr1_sdr0_scg_dsc: pa_fr1_sdr0_scg_dsc {
-				qcom,qmi-dev-name = "pa_fr1_sdr0_scg_dsc";
+			pa_nr_sdr0_scg_dsc: pa_nr_sdr0_scg_dsc {
+				qcom,qmi-dev-name = "pa_nr_sdr0_scg_dsc";
 				#cooling-cells = <2>;
 			};
 
-			pa_fr1_sdr1_scg_dsc: pa_fr1_sdr1_scg_dsc {
-				qcom,qmi-dev-name = "pa_fr1_sdr1_scg_dsc";
+			pa_nr_sdr1_scg_dsc: pa_nr_sdr1_scg_dsc {
+				qcom,qmi-dev-name = "pa_nr_sdr1_scg_dsc";
 				#cooling-cells = <2>;
 			};
 
@@ -92,11 +92,6 @@
 				#cooling-cells = <2>;
 			};
 
-			mmw_ul_throttling_dsc: mmw_ul_throttling_dsc {
-				qcom,qmi-dev-name = "mmw_ul_throttling_dsc";
-				#cooling-cells = <2>;
-			};
-
 			mmw_ific_dsc: mmw_ific_dsc {
 				qcom,qmi-dev-name = "mmw_ific_dsc";
 				#cooling-cells = <2>;
@@ -107,11 +102,6 @@
 				#cooling-cells = <2>;
 			};
 
-			wlan_bw: wlan_bw {
-				qcom,qmi-dev-name = "wlan_bw";
-				#cooling-cells = <2>;
-			};
-
 			modem_vdd: modem_vdd {
 				qcom,qmi-dev-name = "cpuv_restriction_cold";
 				#cooling-cells = <2>;

arch/arm64/boot/dts/vendor/qcom/sdxlemur-thermal.dtsi

@@ -23,18 +23,59 @@
 		thermal-governor = "step_wise";
 		thermal-sensors = <&tsens0 1>;
 		trips {
-			cpu_config: active-config0 {
+			cpu_config0: active-config0 {
 				temperature = <95000>;
-				hysteresis = <0>;
+				hysteresis = <2000>;
+				type = "passive";
+			};
+
+			cpu_config1: active-config1 {
+				temperature = <97000>;
+				hysteresis = <3000>;
+				type = "passive";
+			};
+
+			cpu_config2: active-config2 {
+				temperature = <99000>;
+				hysteresis = <3000>;
 				type = "passive";
 			};
 		};
 
 		cooling-maps {
-			cpu_cdev {
-				trip = <&cpu_config>;
-				cooling-device = <&CPU0 THERMAL_NO_LIMIT
-							THERMAL_NO_LIMIT>;
+			cpu_cdev0 {
+				trip = <&cpu_config0>;
+				cooling-device = <&CPU0 1 1>;
+			};
+
+			cpu_cdev1 {
+				trip = <&cpu_config1>;
+				cooling-device = <&CPU0 2 2>;
+			};
+
+			cpu_cdev2 {
+				trip = <&cpu_config2>;
+				cooling-device = <&CPU0 3 THERMAL_NO_LIMIT>;
+			};
+		};
+	};
+
+	mdmss-0-step {
+		polling-delay-passive = <0>;
+		polling-delay = <0>;
+		thermal-governor = "step_wise";
+		thermal-sensors = <&tsens0 3>;
+		trips {
+			mdmss0_config0: mdmss0-config0 {
+				temperature = <111000>;
+				hysteresis = <3000>;
+				type = "passive";
+			};
+
+			mdmss0_config1: mdmss0-config1 {
+				temperature = <115000>;
+				hysteresis = <2000>;
+				type = "passive";
 			};
 		};
 	};
@@ -43,23 +84,17 @@
 		polling-delay-passive = <0>;
 		polling-delay = <0>;
 		thermal-governor = "step_wise";
-		thermal-sensors = <&tsens0 3>;
+		thermal-sensors = <&tsens0 4>;
 		trips {
 			mdmss1_config0: mdmss1-config0 {
-				temperature = <95000>;
-				hysteresis = <5000>;
+				temperature = <111000>;
+				hysteresis = <3000>;
 				type = "passive";
 			};
 
 			mdmss1_config1: mdmss1-config1 {
-				temperature = <100000>;
-				hysteresis = <5000>;
-				type = "passive";
-			};
-
-			mdmss1_config2: mdmss1-config2 {
-				temperature = <105000>;
-				hysteresis = <5000>;
+				temperature = <115000>;
+				hysteresis = <2000>;
 				type = "passive";
 			};
 		};
@@ -67,41 +102,26 @@
 		cooling-maps {
 			lte_cdev0 {
 				trip = <&mdmss1_config0>;
-				cooling-device = <&modem_lte_dsc 7 7>;
+				cooling-device = <&modem_lte_dsc 8 8>;
 			};
 
 			nr_scg_cdev0 {
 				trip = <&mdmss1_config0>;
-				cooling-device = <&modem_nr_scg_dsc 2 2>;
+				cooling-device = <&modem_nr_scg_dsc 10 10>;
 			};
 
 			nr_cdev0 {
 				trip = <&mdmss1_config0>;
-				cooling-device = <&modem_nr_dsc 4 4>;
+				cooling-device = <&modem_nr_dsc 6 6>;
 			};
 
 			lte_cdev1 {
 				trip = <&mdmss1_config1>;
-				cooling-device = <&modem_lte_dsc 8 8>;
-			};
-
-			nr_scg_cdev1 {
-				trip = <&mdmss1_config1>;
-				cooling-device = <&modem_nr_scg_dsc 10 10>;
+				cooling-device = <&modem_lte_dsc 255 255>;
 			};
 
 			nr_cdev1 {
 				trip = <&mdmss1_config1>;
-				cooling-device = <&modem_nr_dsc 6 6>;
-			};
-
-			lte_cdev2 {
-				trip = <&mdmss1_config2>;
-				cooling-device = <&modem_lte_dsc 255 255>;
-			};
-
-			nr_cdev2 {
-				trip = <&mdmss1_config2>;
 				cooling-device = <&modem_nr_dsc 255 255>;
 			};
 		};
@@ -111,67 +131,19 @@
 		polling-delay-passive = <0>;
 		polling-delay = <0>;
 		thermal-governor = "step_wise";
-		thermal-sensors = <&tsens0 4>;
+		thermal-sensors = <&tsens0 5>;
 		trips {
 			mdmss2_config0: mdmss2-config0 {
-				temperature = <95000>;
-				hysteresis = <5000>;
+				temperature = <111000>;
+				hysteresis = <3000>;
 				type = "passive";
 			};
 
 			mdmss2_config1: mdmss2-config1 {
-				temperature = <100000>;
-				hysteresis = <5000>;
+				temperature = <115000>;
+				hysteresis = <2000>;
 				type = "passive";
 			};
-
-			mdmss2_config2: mdmss2-config2 {
-				temperature = <105000>;
-				hysteresis = <5000>;
-				type = "passive";
-			};
-		};
-
-		cooling-maps {
-			lte_cdev0 {
-				trip = <&mdmss2_config0>;
-				cooling-device = <&modem_lte_dsc 7 7>;
-			};
-
-			nr_scg_cdev0 {
-				trip = <&mdmss2_config0>;
-				cooling-device = <&modem_nr_scg_dsc 2 2>;
-			};
-
-			nr_cdev0 {
-				trip = <&mdmss2_config0>;
-				cooling-device = <&modem_nr_dsc 4 4>;
-			};
-
-			lte_cdev1 {
-				trip = <&mdmss2_config1>;
-				cooling-device = <&modem_lte_dsc 8 8>;
-			};
-
-			nr_scg_cdev1 {
-				trip = <&mdmss2_config1>;
-				cooling-device = <&modem_nr_scg_dsc 10 10>;
-			};
-
-			nr_cdev1 {
-				trip = <&mdmss2_config1>;
-				cooling-device = <&modem_nr_dsc 6 6>;
-			};
-
-			lte_cdev2 {
-				trip = <&mdmss2_config2>;
-				cooling-device = <&modem_lte_dsc 255 255>;
-			};
-
-			nr_cdev2 {
-				trip = <&mdmss2_config2>;
-				cooling-device = <&modem_nr_dsc 255 255>;
-			};
 		};
 	};
 
@@ -179,23 +151,17 @@
 		polling-delay-passive = <0>;
 		polling-delay = <0>;
 		thermal-governor = "step_wise";
-		thermal-sensors = <&tsens0 5>;
+		thermal-sensors = <&tsens0 6>;
 		trips {
 			mdmss3_config0: mdmss3-config0 {
-				temperature = <95000>;
-				hysteresis = <5000>;
+				temperature = <111000>;
+				hysteresis = <3000>;
 				type = "passive";
 			};
 
 			mdmss3_config1: mdmss3-config1 {
-				temperature = <100000>;
-				hysteresis = <5000>;
-				type = "passive";
-			};
-
-			mdmss3_config2: mdmss3-config2 {
-				temperature = <105000>;
-				hysteresis = <5000>;
+				temperature = <115000>;
+				hysteresis = <2000>;
 				type = "passive";
 			};
 		};
@@ -203,41 +169,26 @@
 		cooling-maps {
 			lte_cdev0 {
 				trip = <&mdmss3_config0>;
-				cooling-device = <&modem_lte_dsc 7 7>;
+				cooling-device = <&modem_lte_dsc 8 8>;
 			};
 
 			nr_scg_cdev0 {
 				trip = <&mdmss3_config0>;
-				cooling-device = <&modem_nr_scg_dsc 2 2>;
+				cooling-device = <&modem_nr_scg_dsc 10 10>;
 			};
 
 			nr_cdev0 {
 				trip = <&mdmss3_config0>;
-				cooling-device = <&modem_nr_dsc 4 4>;
+				cooling-device = <&modem_nr_dsc 6 6>;
 			};
 
 			lte_cdev1 {
 				trip = <&mdmss3_config1>;
-				cooling-device = <&modem_lte_dsc 8 8>;
-			};
-
-			nr_scg_cdev1 {
-				trip = <&mdmss3_config1>;
-				cooling-device = <&modem_nr_scg_dsc 10 10>;
+				cooling-device = <&modem_lte_dsc 255 255>;
 			};
 
 			nr_cdev1 {
 				trip = <&mdmss3_config1>;
-				cooling-device = <&modem_nr_dsc 6 6>;
-			};
-
-			lte_cdev2 {
-				trip = <&mdmss3_config2>;
-				cooling-device = <&modem_lte_dsc 255 255>;
-			};
-
-			nr_cdev2 {
-				trip = <&mdmss3_config2>;
 				cooling-device = <&modem_nr_dsc 255 255>;
 			};
 		};

arch/arm64/boot/dts/vendor/qcom/sdxlemur-usb.dtsi

@@ -8,11 +8,12 @@
 
 		iommus = <&apps_smmu 0x1a0 0x0>;
 		qcom,iommu-dma = "atomic";
-		qcom,iommu-dma-addr-pool = <0x40000000 0x5ffe0000>;
+		qcom,iommu-dma-addr-pool = <0x90000000 0x0ffe0000>;
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges;
 		dma-ranges;
+		qcom,iommu-best-fit-algo;
 
 		interrupts-extended = <&pdc 19 IRQ_TYPE_EDGE_RISING>,
 				<&intc GIC_SPI 130 IRQ_TYPE_LEVEL_HIGH>,
@@ -72,7 +73,7 @@
 			tx-fifo-resize;
 			maximum-speed = "super-speed-plus";
 			dr_mode = "otg";
-			snps,xhci-imod-value = <4000>;
+			imod-interval-ns = <1000000>;
 		};
 
 		qcom,usbbam@a704000 {
@@ -116,7 +117,7 @@
 		reg-names = "hsusb_phy_base",
 			"eud_enable_reg";
 		vdd-supply = <&pmx65_l4>;
-		qcom,vdd-voltage-level = <0 912000 912000>;
+		qcom,vdd-voltage-level = <0 880000 912000>;
 		vdda18-supply = <&pmx65_l5>;
 		vdda33-supply = <&pmx65_l10>;
 
@@ -137,7 +138,7 @@
 			"pcs_clamp_enable_reg";
 
 		vdd-supply = <&pmx65_l4>;
-		qcom,vdd-voltage-level = <0 912000 912000>;
+		qcom,vdd-voltage-level = <0 880000 912000>;
 		qcom,vdd-max-load-uA = <47900>;
 		core-supply = <&pmx65_l1>;
 		qcom,core-max-load-uA = <15000>;

arch/arm64/boot/dts/vendor/qcom/sdxlemur-v2-atp.dts

@@ -0,0 +1,12 @@
+/dts-v1/;
+
+#include "sdxlemur-v2.dtsi"
+#include "sdxlemur-atp.dtsi"
+#include "sdxlemur-512mb.dtsi"
+
+/ {
+	model = "Qualcomm Technologies, Inc. SDXLEMUR ATP V2";
+	compatible = "qcom,sdxlemur-atp",
+		"qcom,sdxlemur", "qcom,atp";
+	qcom,board-id = <0x010021 0x200>;
+};

arch/arm64/boot/dts/vendor/qcom/sdxlemur-v2-cdp.dts

@@ -11,5 +11,5 @@
 	model = "Qualcomm Technologies, Inc. SDXLEMUR CDP V2";
 	compatible = "qcom,sdxlemur-cdp",
 		"qcom,sdxlemur", "qcom,cdp";
-	qcom,board-id = <0x20001 0x300>;
+	qcom,board-id = <0x01 0x300>;
 };

arch/arm64/boot/dts/vendor/qcom/sdxlemur-v2-m2-ep-fwa.dts

@@ -0,0 +1,21 @@
+/dts-v1/;
+
+#include "sdxlemur-v2.dtsi"
+#include "sdxlemur-mtp-mbb-pcie-ep-ipq.dtsi"
+#include "sdxlemur-mtp-mbb-m2-ep.dtsi"
+#include "sdxlemur-1024mb.dtsi"
+#include "sdxlemur-v2-m2-ep-fwa.dtsi"
+
+/ {
+	model = "Qualcomm Technologies, Inc. SDXLEMUR M2 EP FWA V2";
+	compatible = "qcom,sdxlemur-mtp",
+		"qcom,sdxlemur", "qcom,mtp";
+	qcom,board-id = <0x11010008 0x311>;
+};
+
+&sdx_ext_ipc {
+	qcom,status-in-gpio = <&tlmm 12 0x00>
+	qcom,status-out-gpio = <&tlmm 13 0x00>
+	qcom,status-out2-gpio = <&tlmm 15 0x00>
+	status = "ok"
+};

arch/arm64/boot/dts/vendor/qcom/sdxlemur-v2-m2-ep-fwa.dtsi

@@ -0,0 +1,2 @@
+/ {
+};

arch/arm64/boot/dts/vendor/qcom/sdxlemur-v2-mtp-cpe-pine1x.dts

@@ -0,0 +1,14 @@
+/dts-v1/;
+
+#include "sdxlemur-v2.dtsi"
+#include "sdxlemur-mtp-cpe.dtsi"
+#include "sdxlemur-mtp-cpe-pine1x.dtsi"
+#include "sdxlemur-1024mb.dtsi"
+#include "sdxlemur-bluetooth.dtsi"
+
+/ {
+	model = "Qualcomm Technologies, Inc. SDXLEMUR MTP CPE 1x Pine V2";
+	compatible = "qcom,sdxlemur-mtp",
+		"qcom,sdxlemur", "qcom,mtp";
+	qcom,board-id = <0x9010008 0x309>;
+};

arch/arm64/boot/dts/vendor/qcom/sdxlemur-v2-mtp-cpe-pine2x.dts

@@ -0,0 +1,14 @@
+/dts-v1/;
+
+#include "sdxlemur-v2.dtsi"
+#include "sdxlemur-mtp-cpe.dtsi"
+#include "sdxlemur-mtp-cpe-pine2x.dtsi"
+#include "sdxlemur-1024mb.dtsi"
+#include "sdxlemur-bluetooth.dtsi"
+
+/ {
+	model = "Qualcomm Technologies, Inc. SDXLEMUR MTP CPE 2x Pine V2";
+	compatible = "qcom,sdxlemur-mtp",
+		"qcom,sdxlemur", "qcom,mtp";
+	qcom,board-id = <0xA010008 0x30A>;
+};

arch/arm64/boot/dts/vendor/qcom/sdxlemur-v2-mtp-cpe.dts

@@ -2,13 +2,15 @@
 
 #include "sdxlemur-v2.dtsi"
 #include "sdxlemur-mtp-cpe.dtsi"
+#include "sdxlemur-mtp-cpe-hsp.dtsi"
 #include "sdxlemur-1024mb-cpe.dtsi"
 #include "sdxlemur-audio.dtsi"
 #include "sdxlemur-mtp-audio-overlay.dtsi"
+#include "sdxlemur-bluetooth.dtsi"
 
 / {
 	model = "Qualcomm Technologies, Inc. SDXLEMUR MTP CPE V2";
 	compatible = "qcom,sdxlemur-mtp",
 		"qcom,sdxlemur", "qcom,mtp";
-	qcom,board-id = <0x6020008 0x306>;
+	qcom,board-id = <0x6010008 0x306>;
 };

arch/arm64/boot/dts/vendor/qcom/sdxlemur-v2-mtp-mbb-emmc-512mb.dts

@@ -0,0 +1,14 @@
+/dts-v1/;
+
+#include "sdxlemur-v2.dtsi"
+#include "sdxlemur-mtp-mbb-pcie-ep.dtsi"
+#include "sdxlemur-mtp-mbb-emmc.dtsi"
+#include "sdxlemur-512mb.dtsi"
+#include "sdxlemur-bluetooth.dtsi"
+
+/ {
+	model = "Qualcomm Technologies, Inc. SDXLEMUR MTP MBB eMMC 512 MB V2";
+	compatible = "qcom,sdxlemur-mtp",
+		"qcom,sdxlemur", "qcom,mtp";
+	qcom,board-id = <0x2010108 0x202>;
+};

arch/arm64/boot/dts/vendor/qcom/sdxlemur-v2-mtp-mbb-emmc.dts

@@ -11,5 +11,5 @@
 	model = "Qualcomm Technologies, Inc. SDXLEMUR MTP MBB eMMC V2";
 	compatible = "qcom,sdxlemur-mtp",
 		"qcom,sdxlemur", "qcom,mtp";
-	qcom,board-id = <0x2020108 0x302>;
+	qcom,board-id = <0x2010108 0x302>;
 };

arch/arm64/boot/dts/vendor/qcom/sdxlemur-v2-mtp-mbb-m2-ep-usb.dts

@@ -0,0 +1,13 @@
+/dts-v1/;
+
+#include "sdxlemur-v2.dtsi"
+#include "sdxlemur-mtp-mbb-pcie-ep.dtsi"
+#include "sdxlemur-mtp-mbb-m2-ep-usb.dtsi"
+#include "sdxlemur-1024mb.dtsi"
+
+/ {
+	model = "Qualcomm Technologies, Inc. SDXLEMUR MTP MBB M2 EP USB V2";
+	compatible = "qcom,sdxlemur-mtp",
+		"qcom,sdxlemur", "qcom,mtp";
+	qcom,board-id = <0x10010008 0x310>;
+};

arch/arm64/boot/dts/vendor/qcom/sdxlemur-v2-mtp-mbb-m2-ep.dts

@@ -0,0 +1,17 @@
+/dts-v1/;
+
+#include "sdxlemur-v2.dtsi"
+#include "sdxlemur-mtp-mbb-pcie-ep.dtsi"
+#include "sdxlemur-mtp-mbb-m2-ep.dtsi"
+#include "sdxlemur-1024mb.dtsi"
+
+/ {
+	model = "Qualcomm Technologies, Inc. SDXLEMUR MTP MBB M2 EP V2";
+	compatible = "qcom,sdxlemur-mtp",
+		"qcom,sdxlemur", "qcom,mtp";
+	qcom,board-id = <0x8010008 0x308>;
+};
+
+&sdx_ext_ipc {
+	status = "ok"
+};

arch/arm64/boot/dts/vendor/qcom/sdxlemur-v2-mtp-mbb-ntn3-pcie.dts

@@ -10,5 +10,5 @@
 	model = "Qualcomm Technologies, Inc. SDXLEMUR MTP MBB NTN3 PCIE V2";
 	compatible = "qcom,sdxlemur-mtp",
 		"qcom,sdxlemur", "qcom,mtp";
-	qcom,board-id = <0x5020008 0x305>;
+	qcom,board-id = <0x5010008 0x305>;
 };

arch/arm64/boot/dts/vendor/qcom/sdxlemur-v2-mtp-mbb-pcie-ep-ipq.dts

@@ -8,5 +8,10 @@
 	model = "Qualcomm Technologies, Inc. SDXLEMUR MTP MBB PCIE-EP V2";
 	compatible = "qcom,sdxlemur-mtp",
 		"qcom,sdxlemur", "qcom,mtp";
-	qcom,board-id = <0xB020008 0x20B>;
+	qcom,board-id = <0xB010008 0x20B>;
+};
+
+&sdx_ext_ipc {
+	ipq807x_attach = <1>;
+	status = "ok"
 };

arch/arm64/boot/dts/vendor/qcom/sdxlemur-v2-mtp-mbb-pcie-ep.dts

@@ -8,5 +8,5 @@
 	model = "Qualcomm Technologies, Inc. SDXLEMUR MTP MBB PCIE-EP V2";
 	compatible = "qcom,sdxlemur-mtp",
 		"qcom,sdxlemur", "qcom,mtp";
-	qcom,board-id = <0x4020008 0x204>;
+	qcom,board-id = <0x4010008 0x204>;
 };

arch/arm64/boot/dts/vendor/qcom/sdxlemur-v2-mtp-mbb-pcie-rc-ep.dts

@@ -8,5 +8,5 @@
 	model = "Qualcomm Technologies, Inc. SDXLEMUR MTP MBB RC PCIE-EP V2";
 	compatible = "qcom,sdxlemur-mtp",
 		"qcom,sdxlemur", "qcom,mtp";
-	qcom,board-id = <0x3020008 0x203>;
+	qcom,board-id = <0x3010008 0x203>;
 };

arch/arm64/boot/dts/vendor/qcom/sdxlemur-v2-mtp-mbb.dts

@@ -6,10 +6,11 @@
 #include "sdxlemur-audio.dtsi"
 #include "sdxlemur-mtp-audio-overlay.dtsi"
 #include "sdxlemur-bluetooth.dtsi"
+#include "display/sdxlemur-qpic-display.dtsi"
 
 / {
 	model = "Qualcomm Technologies, Inc. SDXLEMUR MTP MBB V2";
 	compatible = "qcom,sdxlemur-mtp",
 		"qcom,sdxlemur", "qcom,mtp";
-	qcom,board-id = <0x2020008 0x302>;
+	qcom,board-id = <0x2010008 0x302>;
 };

arch/arm64/boot/dts/vendor/qcom/sdxlemur-v2-mtp.dts

@@ -11,5 +11,5 @@
 	model = "Qualcomm Technologies, Inc. SDXLEMUR MTP V2";
 	compatible = "qcom,sdxlemur-mtp",
 		"qcom,sdxlemur", "qcom,mtp";
-	qcom,board-id = <0x20008 0x300>;
+	qcom,board-id = <0x08 0x300>;
 };

arch/arm64/boot/dts/vendor/qcom/sdxlemur-v2-rcm-pcie-ep.dts

@@ -8,5 +8,5 @@
 	model = "Qualcomm Technologies, Inc. SDXLEMUR RCM PCIe-EP V2";
 	compatible = "qcom,sdxlemur-rcm",
 		"qcom,sdxlemur", "qcom,rcm";
-	qcom,board-id = <0x1020015 0x201>;
+	qcom,board-id = <0x1010015 0x201>;
 };

arch/arm64/boot/dts/vendor/qcom/sdxlemur-v2-rcm-rc-pine1x.dts

@@ -0,0 +1,13 @@
+/dts-v1/;
+
+#include "sdxlemur-v2.dtsi"
+#include "sdxlemur-rcm-rc.dtsi"
+#include "sdxlemur-rcm-rc-pine1x.dtsi"
+#include "sdxlemur-1024mb.dtsi"
+
+/ {
+	model = "Qualcomm Technologies, Inc. SDXLEMUR RCM Root Complex 1x Pine V2";
+	compatible = "qcom,sdxlemur-rcm",
+		"qcom,sdxlemur", "qcom,rcm";
+	qcom,board-id = <0x2010015 0x302>;
+};

arch/arm64/boot/dts/vendor/qcom/sdxlemur-v2-rcm-rc-pine2x.dts

@@ -0,0 +1,13 @@
+/dts-v1/;
+
+#include "sdxlemur-v2.dtsi"
+#include "sdxlemur-rcm-rc.dtsi"
+#include "sdxlemur-rcm-rc-pine2x.dtsi"
+#include "sdxlemur-1024mb.dtsi"
+
+/ {
+	model = "Qualcomm Technologies, Inc. SDXLEMUR RCM Root Complex 2x Pine V2";
+	compatible = "qcom,sdxlemur-rcm",
+		"qcom,sdxlemur", "qcom,rcm";
+	qcom,board-id = <0x3010015 0x303>;
+};

arch/arm64/boot/dts/vendor/qcom/sdxlemur-v2-rcm-rc.dts

@@ -11,5 +11,5 @@
 	model = "Qualcomm Technologies, Inc. SDXLEMUR RCM Root Complex V2";
 	compatible = "qcom,sdxlemur-rcm",
 		"qcom,sdxlemur", "qcom,rcm";
-	qcom,board-id = <0x20015 0x300>;
+	qcom,board-id = <0x10015 0x300>;
 };

arch/arm64/boot/dts/vendor/qcom/sdxlemur-v2.dtsi

@@ -3,159 +3,163 @@
 / {
 	model = "Qualcomm Technologies, Inc. SDXLEMUR V2";
 	compatible = "qcom,sdxlemur";
-	qcom,msm-id = <458 0x20000>, <483 0x20000>;
+	qcom,msm-id = <458 0x20000>, <483 0x20000>, <509 0x20000>;
+};
+
+/* Overriding the BAM node to enable SMMU S1 support in sdxlemur V2
+ * Adding i2c SID's in BAM node, as descriptors buffers for i2c
+ * usecase are allocated in BAM DMA driver.
+ */
+&dma_blsp1 {
+	iommus = <&apps_smmu 0x148 0x1>,
+		<&apps_smmu 0x14a 0x1>,
+		<&apps_smmu 0x14c 0x1>,
+		<&apps_smmu 0x14e 0x1>;
+	qcom,iommu-dma-addr-pool = <0x40000000 0x10000000>;
+	qcom,iommu-geometry = <0x40000000 0x10000000>;
+	qcom,iommu-dma = "fastmap";
 };
 
 &i2c_1 {
-	iommus = <&apps_smmu 0x148 0x0>,
-		<&apps_smmu 0x149 0x0>;
+	iommus = <&apps_smmu 0x148 0x1>;
 	qcom,iommu-dma-addr-pool = <0x40000000 0x10000000>;
 	qcom,iommu-geometry = <0x40000000 0x10000000>;
 	qcom,iommu-dma = "fastmap";
 };
 
 &i2c_2 {
-	iommus = <&apps_smmu 0x14a 0x0>,
-		<&apps_smmu 0x14b 0x0>;
+	iommus = <&apps_smmu 0x14a 0x1>;
 	qcom,iommu-dma-addr-pool = <0x40000000 0x10000000>;
 	qcom,iommu-geometry = <0x40000000 0x10000000>;
 	qcom,iommu-dma = "fastmap";
 };
 
 &i2c_3 {
-	iommus = <&apps_smmu 0x14c 0x0>,
-		<&apps_smmu 0x14d 0x0>;
+	iommus = <&apps_smmu 0x14c 0x1>;
 	qcom,iommu-dma-addr-pool = <0x40000000 0x10000000>;
 	qcom,iommu-geometry = <0x40000000 0x10000000>;
 	qcom,iommu-dma = "fastmap";
 };
 
 &i2c_4 {
-	iommus = <&apps_smmu 0x14e 0x0>,
-		<&apps_smmu 0x14f 0x0>;
+	iommus = <&apps_smmu 0x14e 0x1>;
 	qcom,iommu-dma-addr-pool = <0x40000000 0x10000000>;
 	qcom,iommu-geometry = <0x40000000 0x10000000>;
 	qcom,iommu-dma = "fastmap";
 };
 
 &i2c_5 {
-	iommus = <&apps_smmu 0x148 0x0>,
-		<&apps_smmu 0x149 0x0>;
+	iommus = <&apps_smmu 0x148 0x1>;
 	qcom,iommu-dma-addr-pool = <0x40000000 0x10000000>;
 	qcom,iommu-geometry = <0x40000000 0x10000000>;
 	qcom,iommu-dma = "fastmap";
 };
 
 &i2c_6 {
-	iommus = <&apps_smmu 0x14a 0x0>,
-		<&apps_smmu 0x14b 0x0>;
+	iommus = <&apps_smmu 0x14a 0x1>;
 	qcom,iommu-dma-addr-pool = <0x40000000 0x10000000>;
 	qcom,iommu-geometry = <0x40000000 0x10000000>;
 	qcom,iommu-dma = "fastmap";
 };
 
 &i2c_7 {
-	iommus = <&apps_smmu 0x14e 0x0>,
-		<&apps_smmu 0x14f 0x0>;
+	iommus = <&apps_smmu 0x14e 0x1>;
 	qcom,iommu-dma-addr-pool = <0x40000000 0x10000000>;
 	qcom,iommu-geometry = <0x40000000 0x10000000>;
 	qcom,iommu-dma = "fastmap";
 };
 
 &spi_1 {
-	iommus = <&apps_smmu 0x148 0x0>,
-		<&apps_smmu 0x149 0x0>;
+	iommus = <&apps_smmu 0x148 0x1>;
 	qcom,iommu-dma-addr-pool = <0x40000000 0x10000000>;
 	qcom,iommu-geometry = <0x40000000 0x10000000>;
 	qcom,iommu-dma = "fastmap";
 };
 
 &spi_2 {
-	iommus = <&apps_smmu 0x14a 0x0>,
-		<&apps_smmu 0x14b 0x0>;
+	iommus = <&apps_smmu 0x14a 0x1>;
 	qcom,iommu-dma-addr-pool = <0x40000000 0x10000000>;
 	qcom,iommu-geometry = <0x40000000 0x10000000>;
 	qcom,iommu-dma = "fastmap";
 };
 
 &spi_3 {
-	iommus = <&apps_smmu 0x14c 0x0>,
-		<&apps_smmu 0x14d 0x0>;
+	iommus = <&apps_smmu 0x14c 0x1>;
 	qcom,iommu-dma-addr-pool = <0x40000000 0x10000000>;
 	qcom,iommu-geometry = <0x40000000 0x10000000>;
 	qcom,iommu-dma = "fastmap";
 };
 
 &spi_4 {
-	iommus = <&apps_smmu 0x14e 0x0>,
-		<&apps_smmu 0x14f 0x0>;
+	iommus = <&apps_smmu 0x14e 0x1>;
 	qcom,iommu-dma-addr-pool = <0x40000000 0x10000000>;
 	qcom,iommu-geometry = <0x40000000 0x10000000>;
 	qcom,iommu-dma = "fastmap";
 };
 
 &blsp1_uart1a_hs {
-	iommus = <&apps_smmu 0x140 0x0>,
-		<&apps_smmu 0x141 0x0>;
+	iommus = <&apps_smmu 0x140 0x1>;
 	qcom,iommu-dma-addr-pool = <0x40000000 0x10000000>;
 	qcom,iommu-geometry = <0x40000000 0x10000000>;
 	qcom,iommu-dma = "fastmap";
 };
 
 &blsp1_uart1b_hs {
-	iommus = <&apps_smmu 0x140 0x0>,
-		<&apps_smmu 0x141 0x0>;
+	iommus = <&apps_smmu 0x140 0x1>;
 	qcom,iommu-dma-addr-pool = <0x40000000 0x10000000>;
 	qcom,iommu-geometry = <0x40000000 0x10000000>;
 	qcom,iommu-dma = "fastmap";
 };
 
 &blsp1_uart2a_hs {
-	iommus = <&apps_smmu 0x142 0x0>,
-		<&apps_smmu 0x143 0x0>;
+	iommus = <&apps_smmu 0x142 0x1>;
 	qcom,iommu-dma-addr-pool = <0x40000000 0x10000000>;
 	qcom,iommu-geometry = <0x40000000 0x10000000>;
 	qcom,iommu-dma = "fastmap";
 };
 
 &blsp1_uart2b_hs {
-	iommus = <&apps_smmu 0x142 0x0>,
-		<&apps_smmu 0x143 0x0>;
+	iommus = <&apps_smmu 0x142 0x1>;
 	qcom,iommu-dma-addr-pool = <0x40000000 0x10000000>;
 	qcom,iommu-geometry = <0x40000000 0x10000000>;
 	qcom,iommu-dma = "fastmap";
 };
 
 &blsp1_uart3_hs {
-	iommus = <&apps_smmu 0x144 0x0>,
-		<&apps_smmu 0x145 0x0>;
+	iommus = <&apps_smmu 0x144 0x1>;
 	qcom,iommu-dma-addr-pool = <0x40000000 0x10000000>;
 	qcom,iommu-geometry = <0x40000000 0x10000000>;
 	qcom,iommu-dma = "fastmap";
 };
 
 &blsp1_uart4a_hs {
-	iommus = <&apps_smmu 0x146 0x0>,
-		<&apps_smmu 0x147 0x0>;
+	iommus = <&apps_smmu 0x146 0x1>;
 	qcom,iommu-dma-addr-pool = <0x40000000 0x10000000>;
 	qcom,iommu-geometry = <0x40000000 0x10000000>;
 	qcom,iommu-dma = "fastmap";
 };
 
 &blsp1_uart4b_hs {
-	iommus = <&apps_smmu 0x146 0x0>,
-		<&apps_smmu 0x147 0x0>;
+	iommus = <&apps_smmu 0x146 0x1>;
 	qcom,iommu-dma-addr-pool = <0x40000000 0x10000000>;
 	qcom,iommu-geometry = <0x40000000 0x10000000>;
 	qcom,iommu-dma = "fastmap";
 };
 
+&apsscc {
+	qcom,speed0-bin-v0 =
+		<   345600000 RPMH_REGULATOR_LEVEL_LOW_SVS>,
+		<   576000000 RPMH_REGULATOR_LEVEL_SVS>,
+		<  1094400000 RPMH_REGULATOR_LEVEL_NOM>,
+		<  1804800000 RPMH_REGULATOR_LEVEL_TURBO>;
+};
+
 &cpufreq {
 	qcom,cpufreq-table =
 		<  345600 >,
 		<  576000 >,
 		<  1094400 >,
-		<  1708800 >;
+		<  1804800 >;
 };
 
 &cpu0_cpu_ddr_tbl {
@@ -163,5 +167,14 @@
 		<   345600  MHZ_TO_MBPS( 300, 4) >,
 		<   576000  MHZ_TO_MBPS( 768, 4) >,
 		<  1440000  MHZ_TO_MBPS(1555, 4) >,
-		<  1708800  MHZ_TO_MBPS(2092, 4) >;
+		<  1804800  MHZ_TO_MBPS(2092, 4) >;
+};
+
+&pil_modem {
+	qcom,vdd_mss-uV-uA = <RPMH_REGULATOR_LEVEL_NOM_L1 100000>;
+};
+
+
+&dload_mode {
+	qcom,boot-config-shift = <1 4>;
 };

arch/arm64/boot/dts/vendor/qcom/sdxlemur.dtsi

@@ -196,8 +196,11 @@
 		};
 	};
 
-	dload_mode {
+	dload_mode: dload_mode {
 		compatible = "qcom,dload-mode";
+		reg = <0x786070 0x4>;
+		reg-names = "boot-config";
+		qcom,boot-config-shift = <1 3>;
 	};
 
 	dcc: dcc_v2@117f000 {
@@ -943,7 +946,7 @@
 		vreg-mx-supply = <&VDD_MXA_LEVEL>;
 
 		qcom,vreg-1p8-voltage-level = <1200000 1200000 30000>;
-		qcom,vreg-0p9-voltage-level = <912000 912000 132000>;
+		qcom,vreg-0p9-voltage-level = <912000 880000 132000>;
 		qcom,vreg-mx-voltage-level = <RPMH_REGULATOR_LEVEL_MAX RPMH_REGULATOR_LEVEL_NOM 0>;
 
 		clocks = <&gcc GCC_PCIE_PIPE_CLK>,
@@ -977,8 +980,8 @@
 
 			qcom,pcie-vendor-id = /bits/ 16 <0x17cb>;
 			qcom,pcie-device-id = /bits/ 16 <0x0308>;
-			qcom,pcie-link-speed = <4>;
-			qcom,pcie-phy-ver = <6>;
+			qcom,pcie-link-speed = <3>;
+			qcom,pcie-phy-ver = <7>;
 			qcom,pcie-active-config;
 			qcom,pcie-aggregated-irq;
 			qcom,pcie-mhi-a7-irq;
@@ -986,6 +989,7 @@
 			qcom,mhi-soc-reset-offset = <0xb01b8>;
 			qcom,aoss-rst-clr;
 			qcom,aux-clk = <0x11>;
+			qcom,avoid-reboot-in-d3hot;
 
 			qcom,phy-init = <0x1240 0x01 0x0
 				0x100c 0x02 0x0
@@ -1018,7 +1022,7 @@
 				0x1168 0x0a 0x0
 				0x116c 0x04 0x0
 				0x119c 0x88 0x0
-				0x1174 0x20 0x0
+				0x1174 0x60 0x0
 				0x11a0 0x14 0x0
 				0x11a8 0x0f 0x0
 				0x0220 0x16 0x0
@@ -1123,6 +1127,7 @@
 				0x1370 0x2e 0x0
 				0x155c 0x2e 0x0
 				0x1484 0x08 0x0
+				0x1388 0xaa 0x0
 				0x1200 0x00 0x0
 				0x1244 0x03 0x0>;
 
@@ -1139,7 +1144,7 @@
 			qcom,mhi-ep-msi = <0>;
 			qcom,mhi-version = <0x1000000>;
 			qcom,use-ipa-software-channel;
-			interrupts = <0 145 0>;
+			interrupts = <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "mhi-device-inta";
 			qcom,mhi-ifc-id = <0x030817cb>;
 			qcom,mhi-interrupt;
@@ -1208,7 +1213,6 @@
 		qcom,register-collection-on-crash;
 		qcom,testbus-collection-on-crash;
 		qcom,non-tn-collection-on-crash;
-		qcom,lan-rx-napi;
 		clock-names = "core_clk";
 		clocks = <&rpmhcc RPMH_IPA_CLK>;
 		qcom,interconnect,num-cases = <5>;
@@ -1241,7 +1245,7 @@
 
 		qcom,bus-vector-names = "MIN", "SVS2", "SVS", "NOMINAL",
 		"TURBO";
-		qcom,throughput-threshold = <3000 5000 10000>;
+		qcom,throughput-threshold = <2000 2500 10000>;
 		qcom,scaling-exceptions = <>;
 
 		ipa_smmu_ap: ipa_smmu_ap {
@@ -1445,6 +1449,7 @@
 		qcom,status-in-gpio = <&tlmm 65 0x00>
 		qcom,status-out-gpio = <&tlmm 44 0x00>
 		qcom,status-out2-gpio = <&tlmm 45 0x00>
+		status = "disabled";
 	};
 };
 

arch/arm64/boot/dts/vendor/qcom/sdxnightjar.dtsi

@@ -49,7 +49,7 @@
 
 		mss_mem: mss_region@0x88000000 {
 			no-map;
-			reg = <0x88000000 0x6e00000>;
+			reg = <0x88000000 0x6600000>;
 			label = "mss_mem";
 		};
 
@@ -187,7 +187,7 @@
 		qcom,firmware-name = "modem";
 		qcom,pil-self-auth;
 		qcom,sysmon-id = <0>;
-		qcom,ssctl-instance-id = <0x12>;
+		qcom,ssctl-instance-id = <0x22>;
 		qcom,override-acc;
 		qcom,qdsp6v61-1-1;
 		memory-region = <&mss_mem>;

arch/arm64/boot/dts/vendor/qcom/shima-atp.dtsi

@@ -199,8 +199,8 @@
 	};
 };
 
-&dai_mi2s2 {
-	qcom,msm-mi2s-tx-lines = <1>;
+&dai_mi2s2_tx {
+	qcom,msm-mi2s-lines = <1>;
 	pinctrl-names = "default", "sleep";
 	pinctrl-0 = <&tert_mi2s_sck_active &tert_mi2s_ws_active
 			&tert_mi2s_sd0_active>;

arch/arm64/boot/dts/vendor/qcom/shima-audio.dtsi

@@ -180,9 +180,13 @@
 				"msm-pcm-routing", "msm-compr-dsp",
 				"msm-pcm-dsp-noirq";
 		asoc-cpu = <&dai_dp>, <&dai_dp1>,
-				<&dai_mi2s0>, <&dai_mi2s1>,
-				<&dai_mi2s2>, <&dai_mi2s3>,
-				<&dai_mi2s4>, <&dai_mi2s5>, <&dai_pri_auxpcm>,
+				<&dai_mi2s0_rx>, <&dai_mi2s0_tx>,
+				<&dai_mi2s1_rx>, <&dai_mi2s1_tx>,
+				<&dai_mi2s2_rx>, <&dai_mi2s2_tx>,
+				<&dai_mi2s3_rx>, <&dai_mi2s3_tx>,
+				<&dai_mi2s4_rx>, <&dai_mi2s4_tx>,
+				<&dai_mi2s5_rx>, <&dai_mi2s5_tx>,
+				<&dai_pri_auxpcm>,
 				<&dai_sec_auxpcm>, <&dai_tert_auxpcm>,
 				<&dai_quat_auxpcm>, <&dai_quin_auxpcm>,
 				<&dai_sen_auxpcm>,
@@ -217,6 +221,9 @@
 				"msm-dai-q6-mi2s.0", "msm-dai-q6-mi2s.1",
 				"msm-dai-q6-mi2s.2", "msm-dai-q6-mi2s.3",
 				"msm-dai-q6-mi2s.4", "msm-dai-q6-mi2s.5",
+				"msm-dai-q6-mi2s.6", "msm-dai-q6-mi2s.7",
+				"msm-dai-q6-mi2s.8", "msm-dai-q6-mi2s.9",
+				"msm-dai-q6-mi2s.10", "msm-dai-q6-mi2s.11",
 				"msm-dai-q6-auxpcm.1",
 				"msm-dai-q6-auxpcm.2", "msm-dai-q6-auxpcm.3",
 				"msm-dai-q6-auxpcm.4", "msm-dai-q6-auxpcm.5",

arch/arm64/boot/dts/vendor/qcom/shima-idp.dtsi

@@ -223,8 +223,8 @@
 	};
 };
 
-&dai_mi2s2 {
-	qcom,msm-mi2s-tx-lines = <1>;
+&dai_mi2s2_tx {
+	qcom,msm-mi2s-lines = <1>;
 	pinctrl-names = "default", "sleep";
 	pinctrl-0 = <&tert_mi2s_sck_active &tert_mi2s_ws_active
 			&tert_mi2s_sd0_active>;

arch/arm64/boot/dts/vendor/qcom/shima-qrd.dtsi

@@ -467,8 +467,8 @@
 				  <&bolero>;
 };
 
-&dai_mi2s2 {
-	qcom,msm-mi2s-tx-lines = <1>;
+&dai_mi2s2_tx {
+	qcom,msm-mi2s-lines = <1>;
 	pinctrl-names = "default", "sleep";
 	pinctrl-0 = <&tert_mi2s_sck_active &tert_mi2s_ws_active
 			&tert_mi2s_sd0_active>;

arch/arm64/boot/dts/vendor/qcom/yupik-audio-overlay.dtsi

@@ -488,9 +488,12 @@
 	};
 };
 
-&dai_mi2s1 {
-	qcom,msm-mi2s-rx-lines = <0>;
-	qcom,msm-mi2s-tx-lines = <1>;
+&dai_mi2s1_rx {
+	qcom,msm-mi2s-lines = <0>;
+};
+
+&dai_mi2s1_tx {
+	qcom,msm-mi2s-lines = <1>;
 };
 
 &adsp_loader {

arch/arm64/boot/dts/vendor/qcom/yupik-audio.dtsi

@@ -180,9 +180,13 @@
 				"msm-pcm-routing", "msm-compr-dsp",
 				"msm-pcm-dsp-noirq";
 		asoc-cpu = <&dai_dp>, <&dai_dp1>,
-				<&dai_mi2s0>, <&dai_mi2s1>,
-				<&dai_mi2s2>, <&dai_mi2s3>,
-				<&dai_mi2s4>, <&dai_mi2s5>, <&dai_pri_auxpcm>,
+				<&dai_mi2s0_rx>, <&dai_mi2s0_tx>,
+				<&dai_mi2s1_rx>, <&dai_mi2s1_tx>,
+				<&dai_mi2s2_rx>, <&dai_mi2s2_tx>,
+				<&dai_mi2s3_rx>, <&dai_mi2s3_tx>,
+				<&dai_mi2s4_rx>, <&dai_mi2s4_tx>,
+				<&dai_mi2s5_rx>, <&dai_mi2s5_tx>,
+				<&dai_pri_auxpcm>,
 				<&dai_sec_auxpcm>, <&dai_tert_auxpcm>,
 				<&dai_quat_auxpcm>, <&dai_quin_auxpcm>,
 				<&dai_sen_auxpcm>,
@@ -217,6 +221,9 @@
 				"msm-dai-q6-mi2s.0", "msm-dai-q6-mi2s.1",
 				"msm-dai-q6-mi2s.2", "msm-dai-q6-mi2s.3",
 				"msm-dai-q6-mi2s.4", "msm-dai-q6-mi2s.5",
+				"msm-dai-q6-mi2s.6", "msm-dai-q6-mi2s.7",
+				"msm-dai-q6-mi2s.8", "msm-dai-q6-mi2s.9",
+				"msm-dai-q6-mi2s.10", "msm-dai-q6-mi2s.11",
 				"msm-dai-q6-auxpcm.1",
 				"msm-dai-q6-auxpcm.2", "msm-dai-q6-auxpcm.3",
 				"msm-dai-q6-auxpcm.4", "msm-dai-q6-auxpcm.5",

arch/arm64/boot/dts/vendor/qcom/yupik-gpu.dtsi

@@ -57,8 +57,8 @@
 		qcom,min-access-length = <32>;
 		qcom,ubwc-mode = <3>;
 
-		nvmem-cells = <&gpu_speed_bin>, <&gpu_gaming_bin>;
-		nvmem-cell-names = "speed_bin", "gaming_bin";
+		nvmem-cells = <&gpu_speed_bin>, <&gpu_gaming_bin>, <&gpu_model_bin>;
+		nvmem-cell-names = "speed_bin", "gaming_bin", "gpu_model";
 
 		qcom,tzone-names = "gpuss-0-usr", "gpuss-1-usr";
 
@@ -119,6 +119,26 @@
 			};
 		};
 
+		qcom,gpu-models {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible="qcom,gpu-models";
+
+			qcom,gpu-model@0 {
+				compatible="qcom,adreno-gpu-a643";
+				qcom,gpu-model-id = <172>;
+				qcom,gpu-model = "Adreno643v1";
+				qcom,vk-device-id = <0x06030501>;
+			};
+
+			qcom,gpu-model@1 {
+				compatible="qcom,adreno-gpu-a643";
+				qcom,gpu-model-id = <190>;
+				qcom,gpu-model = "Adreno643v1";
+				qcom,vk-device-id = <0x06030501>;
+			};
+		};
+
 		qcom,gpu-mempools {
 			#address-cells = <1>;
 			#size-cells = <0>;

arch/arm64/boot/dts/vendor/qcom/yupik-hsp.dts

@@ -4,6 +4,6 @@
 
 / {
 	model = "Qualcomm Technologies, Inc. Yupik IDP HSP + SoC";
-	compatible = "qcom,yupik-idp", "qcom,yupik", "qcom,idp";
+	compatible = "qcom,yupik";
 	qcom,board-id = <0 1>;
 };

arch/arm64/boot/dts/vendor/qcom/yupik-iot-hsp-pm7250b-overlay.dts

@@ -0,0 +1,11 @@
+/dts-v1/;
+/plugin/;
+
+#include "yupik-iot-hsp-pm7250b.dtsi"
+
+/ {
+	model = "Qualcomm Technologies, Inc. Yupik IOT HSP + PM7250B";
+	compatible = "qcom,yupik-iot-idp", "qcom,yupik-iot", "qcom,idp";
+	qcom,msm-id = <497 0x10000>;
+	qcom,board-id = <34 1>;
+};

arch/arm64/boot/dts/vendor/qcom/yupik-iot-hsp-pm7250b.dts

@@ -0,0 +1,10 @@
+/dts-v1/;
+
+#include "yupik-iot.dtsi"
+#include "yupik-iot-hsp-pm7250b.dtsi"
+
+/ {
+	model = "Qualcomm Technologies, Inc. Yupik IOT HSP + PM7250B";
+	compatible = "qcom,yupik-iot-idp", "qcom,yupik-iot", "qcom,idp";
+	qcom,board-id = <34 1>;
+};

arch/arm64/boot/dts/vendor/qcom/yupik-iot-hsp-pm7250b.dtsi

@@ -0,0 +1,63 @@
+#include <dt-bindings/interconnect/qcom,yupik.h>
+#include "yupik-iot-idp-pm7250b.dtsi"
+#include "qcx6490-cnss.dtsi"
+
+&pcie0 {
+	status = "ok"
+};
+
+&pcie0_msi {
+	status = "ok"
+};
+
+&pcie1 {
+	status = "ok"
+	qcom,boot-option = <0x0>;
+	qcom,ep-gpio = <&tlmm 19 0>;
+	pinctrl-0 = <&pcie1_perst_default
+			&pcie1_clkreq_default
+			&pcie1_wake_default
+			&pcie1_ep_default>;
+	pinctrl-1 = <&pcie1_perst_default
+			&pcie1_clkreq_sleep
+			&pcie1_wake_default
+			&pcie1_ep_default>;
+};
+
+&pcie1_msi {
+	status = "ok"
+};
+
+&pm7325_gpios {
+	usb2_vbus_boost {
+		usb2_vbus_boost_default: usb2_vbus_boost_default {
+			pins = "gpio8";
+			function = "normal";
+			output-low;
+			power-source = <0>;	/* 1.8V input supply */
+		};
+	};
+};
+
+&soc {
+	usb2_vbus_boost_reg: usb2_vbus_boost_reg {
+		compatible = "regulator-fixed";
+		regulator-name = "usb2_vbus_boost_vreg";
+		startup-delay-us = <4000>;
+		enable-active-high;
+		gpios = <&pm7325_gpios 8 0>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&usb2_vbus_boost_default>;
+	};
+};
+
+&usb1 {
+	vbus_dwc3-supply = <&usb2_vbus_boost_reg>;
+	qcom,default-mode-none;
+	status = "ok"
+};
+
+&usb2_phy1 {
+	status = "ok"
+};

arch/arm64/boot/dts/vendor/qcom/yupik-iot-hsp.dtsi

@@ -1,4 +1,65 @@
 #include "yupik-iot-idp.dtsi"
+#include "qcx6490-cnss.dtsi"
 
 &soc {
 };
+
+&pcie0 {
+	status = "ok"
+};
+
+&pcie0_msi {
+	status = "ok"
+};
+
+&pcie1 {
+	status = "ok"
+	qcom,boot-option = <0x0>;
+	qcom,ep-gpio = <&tlmm 19 0>;
+	pinctrl-0 = <&pcie1_perst_default
+			&pcie1_clkreq_default
+			&pcie1_wake_default
+			&pcie1_ep_default>;
+	pinctrl-1 = <&pcie1_perst_default
+			&pcie1_clkreq_sleep
+			&pcie1_wake_default
+			&pcie1_ep_default>;
+};
+
+&pcie1_msi {
+	status = "ok"
+};
+
+&pm7325_gpios {
+	usb2_vbus_boost {
+		usb2_vbus_boost_default: usb2_vbus_boost_default {
+			pins = "gpio8";
+			function = "normal";
+			output-low;
+			power-source = <0>;	/* 1.8V input supply */
+		};
+	};
+};
+
+&soc {
+	usb2_vbus_boost_reg: usb2_vbus_boost_reg {
+		compatible = "regulator-fixed";
+		regulator-name = "usb2_vbus_boost_vreg";
+		startup-delay-us = <4000>;
+		enable-active-high;
+		gpios = <&pm7325_gpios 8 0>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&usb2_vbus_boost_default>;
+	};
+};
+
+&usb1 {
+	vbus_dwc3-supply = <&usb2_vbus_boost_reg>;
+	qcom,default-mode-none;
+	status = "ok"
+};
+
+&usb2_phy1 {
+	status = "ok"
+};

arch/arm64/boot/dts/vendor/qcom/yupik-iot-idp-pm7250b-overlay.dts

@@ -0,0 +1,11 @@
+/dts-v1/;
+/plugin/;
+
+#include "yupik-iot-idp-pm7250b.dtsi"
+
+/ {
+	model = "Qualcomm Technologies, Inc. Yupik IOT IDP + PM7250B";
+	compatible = "qcom,yupik-iot-idp", "qcom,yupik-iot", "qcom,idp";
+	qcom,msm-id = <497 0x10000>;
+	qcom,board-id = <34 0>;
+};

arch/arm64/boot/dts/vendor/qcom/yupik-iot-idp-pm7250b.dts

@@ -0,0 +1,10 @@
+/dts-v1/;
+
+#include "yupik-iot.dtsi"
+#include "yupik-iot-idp-pm7250b.dtsi"
+
+/ {
+	model = "Qualcomm Technologies, Inc. Yupik IOT IDP + PM7250B";
+	compatible = "qcom,yupik-iot-idp", "qcom,yupik-iot", "qcom,idp";
+	qcom,board-id = <34 0>;
+};

arch/arm64/boot/dts/vendor/qcom/yupik-iot-idp-pm7250b.dtsi

@@ -0,0 +1 @@
+#include "yupik-idp-pm7250b.dtsi"

arch/arm64/boot/dts/vendor/qcom/yupik-iot-idp.dtsi

@@ -1,62 +1 @@
 #include "yupik-idp.dtsi"
-#include "qcx6490-cnss.dtsi"
-
-&pcie0 {
-	status = "ok"
-};
-
-&pcie0_msi {
-	status = "ok"
-};
-
-&pcie1 {
-	status = "ok"
-	qcom,boot-option = <0x0>;
-	qcom,ep-gpio = <&tlmm 19 0>;
-	pinctrl-0 = <&pcie1_perst_default
-			&pcie1_clkreq_default
-			&pcie1_wake_default
-			&pcie1_ep_default>;
-	pinctrl-1 = <&pcie1_perst_default
-			&pcie1_clkreq_sleep
-			&pcie1_wake_default
-			&pcie1_ep_default>;
-};
-
-&pcie1_msi {
-	status = "ok"
-};
-
-&pm7325_gpios {
-	usb2_vbus_boost {
-		usb2_vbus_boost_default: usb2_vbus_boost_default {
-			pins = "gpio8";
-			function = "normal";
-			output-low;
-			power-source = <0>;	/* 1.8V input supply */
-		};
-	};
-};
-
-&soc {
-	usb2_vbus_boost_reg: usb2_vbus_boost_reg {
-		compatible = "regulator-fixed";
-		regulator-name = "usb2_vbus_boost_vreg";
-		startup-delay-us = <4000>;
-		enable-active-high;
-		gpios = <&pm7325_gpios 8 0>;
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&usb2_vbus_boost_default>;
-	};
-};
-
-&usb1 {
-	vbus_dwc3-supply = <&usb2_vbus_boost_reg>;
-	qcom,default-mode-none;
-	status = "ok"
-};
-
-&usb2_phy1 {
-	status = "ok"
-};

arch/arm64/boot/dts/vendor/qcom/yupik-pinctrl.dtsi

@@ -8,7 +8,6 @@
 		interrupt-controller;
 		#interrupt-cells = <2>;
 		wakeup-parent = <&pdc>;
-		qcom,tlmm-mpm-wake-control;
 
 		qupv3_se0_i2c_pins: qupv3_se0_i2c_pins {
 			qupv3_se0_i2c_active: qupv3_se0_i2c_active {

arch/arm64/boot/dts/vendor/qcom/yupik-regulators.dtsi

@@ -46,6 +46,11 @@
 	rpmh-regulator-smpb8 {
 		compatible = "qcom,rpmh-vrm-regulator";
 		qcom,resource-name = "smpb8";
+		qcom,regulator-type = "pmic5-hfsmps";
+		qcom,supported-modes =
+			<RPMH_REGULATOR_MODE_RET
+			RPMH_REGULATOR_MODE_AUTO>;
+		qcom,mode-threshold-currents = <0 200000>;
 		S8B:
 		pm7325_s8: regulator-pm7325-s8 {
 			regulator-name = "pm7325_s8";
@@ -53,6 +58,7 @@
 			regulator-min-microvolt = <1200000>;
 			regulator-max-microvolt = <1500000>;
 			qcom,init-voltage = <1272000>;
+			qcom,init-mode = <RPMH_REGULATOR_MODE_RET>;
 		};
 	};
 

arch/arm64/boot/dts/vendor/qcom/yupik.dtsi

@@ -5047,6 +5047,11 @@
 			bits = <5 1>;
 		};
 
+		gpu_model_bin: gpu_model_bin@1e9 {
+			reg = <0x1e9 0x2>;
+			bits = <5 8>;
+		};
+
 		feat_conf_m7: feat_conf_m7@6020 {
 			reg = <0x6020 0x4>;
 		};

arch/arm64/boot/dts/vendor/qcom/yupikp-hsp.dts

@@ -4,6 +4,6 @@
 
 / {
 	model = "Qualcomm Technologies, Inc. YupikP IDP HSP + SoC";
-	compatible = "qcom,yupikp-idp", "qcom,yupikp", "qcom,idp";
+	compatible = "qcom,yupikp";
 	qcom,board-id = <0 1>;
 };

arch/arm64/boot/dts/vendor/qcom/yupikp-iot-hsp-pm7250b-overlay.dts

@@ -0,0 +1,11 @@
+/dts-v1/;
+/plugin/;
+
+#include "yupikp-iot-hsp-pm7250b.dtsi"
+
+/ {
+	model = "Qualcomm Technologies, Inc. YupikP IOT HSP + PM7250B";
+	compatible = "qcom,yupikp-iot-idp", "qcom,yupikp-iot", "qcom,idp";
+	qcom,msm-id = <498 0x10000>;
+	qcom,board-id = <34 1>;
+};

arch/arm64/boot/dts/vendor/qcom/yupikp-iot-hsp-pm7250b.dts

@@ -0,0 +1,10 @@
+/dts-v1/;
+
+#include "yupikp-iot.dtsi"
+#include "yupikp-iot-hsp-pm7250b.dtsi"
+
+/ {
+	model = "Qualcomm Technologies, Inc. YupikP IOT HSP + PM7250B";
+	compatible = "qcom,yupikp-iot-idp", "qcom,yupikp-iot", "qcom,idp";
+	qcom,board-id = <34 1>;
+};

arch/arm64/boot/dts/vendor/qcom/yupikp-iot-hsp-pm7250b.dtsi

@@ -0,0 +1 @@
+#include "yupik-iot-hsp-pm7250b.dtsi"

arch/arm64/boot/dts/vendor/qcom/yupikp-iot-hsp.dtsi

@@ -1 +1,62 @@
 #include "yupikp-iot-idp.dtsi"
+#include "qcx6490-cnss.dtsi"
+
+&pcie0 {
+	status = "ok"
+};
+
+&pcie0_msi {
+	status = "ok"
+};
+
+&pcie1 {
+	status = "ok"
+	qcom,boot-option = <0x0>;
+	qcom,ep-gpio = <&tlmm 19 0>;
+	pinctrl-0 = <&pcie1_perst_default
+			&pcie1_clkreq_default
+			&pcie1_wake_default
+			&pcie1_ep_default>;
+	pinctrl-1 = <&pcie1_perst_default
+			&pcie1_clkreq_sleep
+			&pcie1_wake_default
+			&pcie1_ep_default>;
+};
+
+&pcie1_msi {
+	status = "ok"
+};
+
+&pm7325_gpios {
+	usb2_vbus_boost {
+		usb2_vbus_boost_default: usb2_vbus_boost_default {
+			pins = "gpio8";
+			function = "normal";
+			output-low;
+			power-source = <0>;	/* 1.8V input supply */
+		};
+	};
+};
+
+&soc {
+	usb2_vbus_boost_reg: usb2_vbus_boost_reg {
+		compatible = "regulator-fixed";
+		regulator-name = "usb2_vbus_boost_vreg";
+		startup-delay-us = <4000>;
+		enable-active-high;
+		gpios = <&pm7325_gpios 8 0>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&usb2_vbus_boost_default>;
+	};
+};
+
+&usb1 {
+	vbus_dwc3-supply = <&usb2_vbus_boost_reg>;
+	qcom,default-mode-none;
+	status = "ok"
+};
+
+&usb2_phy1 {
+	status = "ok"
+};

arch/arm64/boot/dts/vendor/qcom/yupikp-iot-idp-pm7250b-overlay.dts

@@ -0,0 +1,11 @@
+/dts-v1/;
+/plugin/;
+
+#include "yupikp-iot-idp-pm7250b.dtsi"
+
+/ {
+	model = "Qualcomm Technologies, Inc. YupikP IOT IDP + PM7250B";
+	compatible = "qcom,yupikp-iot-idp", "qcom,yupikp-iot", "qcom,idp";
+	qcom,msm-id = <498 0x10000>;
+	qcom,board-id = <34 0>;
+};

arch/arm64/boot/dts/vendor/qcom/yupikp-iot-idp-pm7250b.dts

@@ -0,0 +1,10 @@
+/dts-v1/;
+
+#include "yupikp-iot.dtsi"
+#include "yupikp-iot-idp-pm7250b.dtsi"
+
+/ {
+	model = "Qualcomm Technologies, Inc. YupikP IOT IDP + PM7250B";
+	compatible = "qcom,yupikp-iot-idp", "qcom,yupikp-iot", "qcom,idp";
+	qcom,board-id = <34 0>;
+};

arch/arm64/boot/dts/vendor/qcom/yupikp-iot-idp-pm7250b.dtsi

@@ -0,0 +1 @@
+#include "yupik-iot-idp-pm7250b.dtsi"