The wakeup value needs to be programmed for cx-ret mode as well.
Update the state id to 0x134 to indicate trustzone to program
wakeup value.
Change-Id: I25143ff78842c7d415f46d0295cfce30b5727f96
The wakeup value needs to be programmed for cx-off mode as well.
Update the state id to 0x234 to indicate trustzone to program
wakeup value.
Change-Id: I3fcb7c66b4d796b121fce4059574d467f61f91a9
Cx-off mode is not supported for yupik. Update the mode id to
exercise cx-ret mode instead of cx-off.
Change-Id: I685d2869c58d99edc4c3631c0c74ae08877ee03a
Add quiet-therm skin thermal zone mitigation rule with
gpu, cdsp and modem_skin as cooling devices based on
latest recommendations.
Change-Id: I25e18a1a693f3107be823ea6dd666084e4f84a2c
Add the QMP and QMP DEBUGFS node to facilitiate communication with AOP.
The QMP driver sends messages using the AOP msgram with a mailbox like
protocol.
Change-Id: I71d3fe058ff98d2000c61d91b3601c3d6217ed34
Add the device tree entries for glink driver and glink packet driver
to provide the communication with remote peripherals.
Change-Id: Ibe804ad78b57a7eabc764227e40316e8d9f16fe3
Add support for QMI beamer ADC and RF sensors to apps.
It enables these sensors as thermal zone sensors so
that we can read and set trip thresholds via
thermal zone.
Change-Id: I000d335dc2ee82afd4b3f41425ff296205e6f922
The old watchdog entry did not account for the new watchdog
changes. This changes it to be compatible with the new watchdog
driver.
Change-Id: I18542ea7803e5ac2d32b8c41c876957fb2c9f592
Update core isolation and hotplug threshold for silver CPUs to 110C
and 112C. Update core isolation and hotplug threshold for gold and
gold plus to 108C and 110C.
GPU thermal mitigation configuration uses a virtual sensor, which will
estimate the max of two GPU sensors. Change the GPU thermal rule to
directly use these individual sensors in two separate rule to achieve a
better thermal control.
Change-Id: I8ee76573e9bef956ca7833d34c8f8aecf3adaa7e
Enabling LCD_REG_EN gpio on shima pinctrls and LCD_BKLT_PWM
on shima pmic overlays on shima target.
Change-Id: If02438f5c28160b643248e3b403c65083e9b6e56
Add USB3_DP_COM_TYPEC_STATUS register for Lahaina and Shima,
this register's bit0 is used indicates the type-c orientation.
Change-Id: I42e35da3074497f24858a313ad4d9235b4729423
Add shared memory support to enable rmt_storage service
in userspace that allows other processor to access the
primary storage device to store its data.
Change-Id: I531df175ed7af586f29e274f174b1e7e6508b84c
Add panel information for amoled-ecm device so that the driver
can get display off/on notification from the DRM for the active
panel and disable/re-enable ECM accordingly.
Change-Id: I5dc22cd1b669e92991325f7be8ef4536a140277c
Add a bidirectional message queue in trusted vm for display. This
message queue will be used to send display custom data across
the vm's.
Change-Id: I0e6bb8116acc126642a5bb57fe90fee011acab19
L9B supply won't really support retention mode on shima, so move it
from RM to LPM by increasing the load to 10mA.
Change-Id: Ie3f10de1c63a123dae2c5dc2bf7a3ea5a6decc5a
QCA6490 requires additional voltage regulator for internal power
amplifier. Add config for TCS CMD offset to enable this regulator.
Change-Id: Iea43e40b95f7bf36ab2bf0dd36039fd21f213be5
Update the qmp register macro definition file name from target specific
to generic 5nm combo and uni file.
Change-Id: I58da7126a19985e1fa26a71bff90fd83f0c2fcbb
