Currently, for any WDSP errors, the driver collects the debug
dumps/information based on trigger from userspace. This is protected
under CONFIG_DEBUG_FS and should not be run unless stress tests are
executed and this functionality is explicitly enabled since
performing debug dumps could possible leave the WDSP in bad state.
Add debug node to control dumping debug information and not rely
only on CONFIG_DEBUG_FS
To enable debug dumps:
echo 1 > /sys/kernel/debug/wdsp0/debug_dump_enable
To disable debug dumps:
echo 0 > /sys/kernel/debug/wdsp0/debug_dump_enable
Change-Id: I67d8781839d9caee16e6bf6a5befd9010ccaafc0
Signed-off-by: Bhalchandra Gajare <gajare@codeaurora.org>
Signed-off-by: Xiaoyu Ye <benyxy@codeaurora.org>
Use msmsteppe target name instead of macro as macro
cannot be used in target rc file.
Signed-off-by: Ramprasad Katkam <katkam@codeaurora.org>
Change-Id: I0f3ec299b28b7dfd9f8ac9985eea0c22a4611f9e
Enable power supplies and reset of Tanggu
CRs-Fixed: 2281591
Change-Id: I7d693263f328b51d2f333bddac5e15e98a5f9f51
Signed-off-by: Tanya Dixit <tdixit@codeaurora.org>
Total size was incorrectly adjusted after determining
IID param size in SET_UI_PROPERTY. Fix total size with
correct APR packet and param sizes.
Change-Id: I5874b470811733e60b40cc240d4c0db995b30bac
Signed-off-by: Vikram Panduranga <vpandura@codeaurora.org>
ASoC core assigns dai id value to num_dais if
AIF dai-id passed is 0. Since we have different macros
passing AIF dai-id as 0, they are replaced in ASoC core.
To handle this, update AIF dai-id in respective macros
to start with value 1.
Change-Id: I222c088289292aa226c90710e56a8c94af5615cd
Signed-off-by: Laxminath Kasam <lkasam@codeaurora.org>
Add interface to read swr port mapping from device
tree and call connect port to swr interface from
wcd937x codec driver.
Change-Id: I82e8d7a8063b725292e0d7ca5e519f279289efe0
Signed-off-by: Ramprasad Katkam <katkam@codeaurora.org>
Check if speaker protection is enabled before registering for
DC detection events.
CRs-Fixed: 2244131
Change-Id: If2f9f777534ee5fe9024ba1080d0b73d3f750159
Signed-off-by: Vignesh Kulothungan <vigneshk@codeaurora.org>
For ADIE loopback, MCLK needs to be enabled.
Associate the macro MCLK widgets to respective
rx and tx paths in route map.
Change-Id: I5632c3016146c5c5d822ae6fe438010904cf434b
Signed-off-by: Laxminath Kasam <lkasam@codeaurora.org>
On bolero and tanggu combination, enable digital side
class-H by default.
Change-Id: I366a7217dbbe7640846275eea57ef0c61cfcdf5e
Signed-off-by: Laxminath Kasam <lkasam@codeaurora.org>
When stereo playback start and temperature read
initiated at same time, one of speaker PA bits are
not set in particular race scenario. Handle the
broadcast check in soundwire framework to ensure
broadcast is disabled only when respective gr_sid
slave calls swr_remove_from_group.
Change-Id: I6f82a8c3c0f39dc20c1def09c1728ce4c26c2f5d
Signed-off-by: Laxminath Kasam <lkasam@codeaurora.org>
When temperature on a single wsa881x device is being read,
then soundwire master wakes up both wsa881x devices but
regcache_sync is happening only for one wsa881x device on
which the temperature is being read. This results in
audio playback mute after temperature read. Fix the
regcache sync during temperature read and playback usecase.
Change-Id: I856b96517c629ac685bbc25caabee841037106c8
Signed-off-by: Laxminath Kasam <lkasam@codeaurora.org>
When temperature on a single wsa881x device is being read,
then soundwire master wakes up both wsa881x devices but
regcache_sync is happening only for one wsa881x device on
which the temperature is being read. This results in
audio playback mute after temperature read. Fix the
regcache sync during temperature read and playback usecase.
Change-Id: I054f4432d7ae7bce922341ad62b20544cccd5865
Signed-off-by: Sudheer Papothi <spapothi@codeaurora.org>
Due to the local char array that stores the codec dsp control command
is not initialized, an invalid command could cause the stack content
to be printed out in kernel dmesg. Initialize the array with memset.
Change-Id: I739eacb5058275c91bef67505531097cb364b93e
Signed-off-by: Xiaoyu Ye <benyxy@codeaurora.org>
Due to the local char array that stores the codec dsp control command
is not initialized, an invalid command could cause the stack content
to be printed out in kernel dmesg. Initialize the array with memset.
Change-Id: I07211c4cc06b2c2df21b674e6812c4d5efc45dc4
Signed-off-by: Xiaoyu Ye <benyxy@codeaurora.org>
Fix set sampling rates for Rx Codec DMA interfaces.
Use uint32 instead of boolean properties for
audio interfaces and tavil codec enablement in
sm6150 target.
CRs-Fixed: 2281591
Change-Id: Id5cb212a8e319437c0efd02e9a900eedf63eae58
Signed-off-by: Aditya Bavanari <abavanar@codeaurora.org>
Add wcd937x swr slave and codec driver.
This adds only basic support for codec registration.
Change-Id: I87519a234f14d34a019c8f66652b7224759e639c
Signed-off-by: Rohit kumar <rohitkr@codeaurora.org>
