Currently q6lsm driver only allows buffer to be allocated for
SVA sound model with size larger than 512 byte in function
q6lsm_snd_model_buf_alloc.This causes issue when a valid SVA
sound model is smaller than 512 byte. Since there is no
restriction in ADSP for sound model size, remove this size
checking to allow sound models with smaller size.
Change-Id: I716dc8c0e1a4e3189cd334ef692ff07f3e4635db
Signed-off-by: Xiaoyu Ye <benyxy@codeaurora.org>
nvmem_cell_read() return no of bytes read in 'len' variable and
allocates similiar bytes of memory for buffer. Copy only these
number of bytes from buf to avoid out of bounds issues.
Change-Id: I712e5058d15deba939b6a743fcf5bff33ac51f84
Signed-off-by: Ajit Pandey <ajitp@codeaurora.org>
Update PCM ID with correct values in comments.
Change-Id: Ie456481aa57f0adebb20921d8d0f0d25c7b714e0
Signed-off-by: Laxminath Kasam <lkasam@codeaurora.org>
After master init sets COMP_CFG, wait for soundwire link
status to be connected for SWR version 1.6. Update wait
for soundwire link disconnect for all masters.
Change-Id: I0c0b34f225f88f1b3838b0aa653b57b2c7c0cc40
Signed-off-by: Laxminath Kasam <lkasam@codeaurora.org>
During SSR, sometimes swr get logical addr fails.
Add sufficient delay after reset and retry logic
for get logical addr.
Change-Id: I2a932e99896e0055f3b35f9b251008612f43b79f
Signed-off-by: Laxminath Kasam <lkasam@codeaurora.org>
On receive of change enum slave status interrupt, update
slave host_irq bit for all attached slave dev_nums.
Change-Id: Idaad7a73a7ba9ab271f3fb6974f8d09df3f957b8
Signed-off-by: Laxminath Kasam <lkasam@codeaurora.org>
Add support to handle wsa883x codec interrupts and runtime
detection of wsa883x variant.
Change-Id: I06fc113a390c04e890062761cff8ae7436acb662
Signed-off-by: Sudheer Papothi <spapothi@codeaurora.org>
Mask bus clash interrupt before clock stop mode to avoid
misfire of the interrupt. Clear and enable the interrupt
after clock is enabled.
Change-Id: I494073a668d298eef466c0f10ab202c3c69f9968
Signed-off-by: Sudheer Papothi <spapothi@codeaurora.org>
Enable IRQ for wakeup is called multiple times resulting in
throttling. This is because irq is not disabled after enablement.
Disable wakeup irq in runtime resume to fix the issue. Also
add check so that irq is not disabled more than once.
Change-Id: Ib5b7493298beb3ca4bcf78b2adbd7d4ac9ce6111
Signed-off-by: Vatsal Bucha <vbucha@codeaurora.org>
Check comp status based on active and inactive request
and return once status met.
Change-Id: I75669558875d8ab6fc23a02c888e6083e15aee08
Signed-off-by: Laxminath Kasam <lkasam@codeaurora.org>
Update rx droop based on sampling rate to avoid change in
gains between different sampling rates.
Change-Id: Icb2b0bc51a61395c2ee96f63c29555614fe9e505
Signed-off-by: Sudheer Papothi <spapothi@codeaurora.org>
