This change updates plane's dirty flag with QoS
value to ensure QoS gets reprogrammed with new FPS
settings. This is required as QoS values will change
with FPS.
Change-Id: I377b99da2a640d375bd48477f149197b332e7f7b
Signed-off-by: Samantha Tran <samtran@codeaurora.org>
Updating qos remap updates requires reading registers to update values,
this adds additional CPU processing when in reality this update
is only needed once.
Bug: 142504774
Change-Id: Iec8d4dfd858b0602db7d2275b6b716dbcffe0d2f
(cherry picked from commit dbd1cfbc21db4b9bd4f1a4fc234cedc314fa1265)
Signed-off-by: Adrian Salido <salidoa@google.com>
Signed-off-by: Samantha Tran <samtran@codeaurora.org>
This change introduces pre-downscaling values to the path where
these values are not provided by userspace. Currently, pre-downscaling
is only allowed by a factor of 2.2 in the x direction. With this
change pre-downscaling will support >2.2 up to 4 in the x direction.
Change-Id: I04d1b07243a5973e9338ea2a212280985b31b6a3
Signed-off-by: Samantha Tran <samtran@codeaurora.org>
VFP or HFP is adjusted to achieve constant fps during dynamic
DSI clock switch. This feature is not supported for command
mode. So, add check to skip porch calculation for command mode.
Change-Id: I5fa76d6536a55b2a19f24c0e14b6861e1f4c8f25
Signed-off-by: Lipsa Rout <lrout@codeaurora.org>
Signed-off-by: Satya Rama Aditya Pinapala <psraditya30@codeaurora.org>
This change updates the parsing of timing nodes to check
the mode of operation as video or command. In command mode,
for each timing node, num of supported dfps rate is always
one. Accordingly, update the num_dfps_rate to 1 for
command mode.
Change-Id: I5098c7e0d4d2320609d6e10031eaef78c1d8b3c1
Signed-off-by: Lipsa Rout <lrout@codeaurora.org>
Signed-off-by: Satya Rama Aditya Pinapala <psraditya30@codeaurora.org>
Panel's physical width/height larger than 255mm is getting
truncated due to type conversion into smaller type.
Change-Id: I826fb2db542146c07d8379951563430b7da8288c
Signed-off-by: Rajeev Nandan <rajeevny@codeaurora.org>
Signed-off-by: Satya Rama Aditya Pinapala <psraditya30@codeaurora.org>
Add support to allow creation of debugfs node only if
CONFIG_DEBUG_FS is enabled.
Change-Id: I1ae2c4188a99e3ed88f59fc021efc01407bf942d
Signed-off-by: Harigovindan P <harigovi@codeaurora.org>
Signed-off-by: Satya Rama Aditya Pinapala <psraditya30@codeaurora.org>
Add support to allow creation of debugfs node only if
CONFIG_DEBUG_FS is enabled.
Change-Id: Iaeaf51b3654c9458cf8131a9756e6b905007c4ae
Signed-off-by: Krishna Manikandan <mkrishn@codeaurora.org>
Signed-off-by: Samantha Tran <samtran@codeaurora.org>
The color-processing partial update check wrongly
assumes that all pipes in a CRTC have a DSPP attached.
This inhibits the use of any LMs without a valid DSPP.
Fix the issue by removing this invalid check since whenever
a DSPP feature is required, the HW resource availability is
already confirmed during the color-processing property validation.
Change-Id: I5b4565865644e4a0fa3d0542a299067f21756863
Signed-off-by: Amine Najahi <anajahi@codeaurora.org>
Restart the timeline for the idle power collapse delayed work
timer for every resource control kickoff instead of only during
a power state change. This will prevent entering mode2 at
unexpected times during active scanouts.
Change-Id: I001157ff7e6b6246e26d537e30d8617cab9cb463
Signed-off-by: Steve Cohen <cohens@codeaurora.org>
Add a check to escape the DSC allocation once the requested
number of DSCs has been reached and a pair is not required
for the last DSC allocated. This issue was introduced when
trying to allow for quad DSC, which broke single DSC use.
Change-Id: I4bc368004f92570d588e76ceb832d63fd3bb15d7
Signed-off-by: Thomas Dedinsky <tdedinsk@codeaurora.org>
While running the panel in simulation mode using sim-swte, ESD check is
invalid. The change doesn't set the ESD capabilities if watchdog timer
is being used for TE.
Change-Id: I375f369ad4602f21da6151e526e7b6e78fcea524
Signed-off-by: Satya Rama Aditya Pinapala <psraditya30@codeaurora.org>
This change adds support for regdma accelerated programming of
partial update offsets for SPR hw block and validation of ROI
during atomic check based on SPR hw block limitations.
Change-Id: I9e20af4ba7752e8a4af5e9738612c57603163744
Signed-off-by: Prabhanjan Kandula <pkandula@codeaurora.org>
Current computation of line time does not include compression ratio
from either DSC or VDC. This change stores source bpp and target bpp in
sde_crtc during sde encoder mode set to be used while calculating line
time.
Change-Id: Ib1e045dce17fcf006447d4562b402cc3f214ed8c
Signed-off-by: Samantha Tran <samtran@codeaurora.org>
From Lahaina onwards, for compressed DSI output, widebus should be enabled.
In widebus mode, 6 bytes of data are transmitted per pclk.
For uncompressed output, widebus must be disabled to transmit 3 bytes
of uncompressed data per pclk.
Change-Id: I7fc0bdb2e1678152d57b4cbb8295063a2ba8ae73
Signed-off-by: Rajkumar Subbiah <rsubbia@codeaurora.org>
From Lahaina onwards, widebus is enabled for compressed DSI stream.
This change adjusts interface timing parameters to account for widebus.
Change-Id: Ie6b739ed2cdb515064e3a94404b3e0fe07755d7e
Signed-off-by: Rajkumar Subbiah <rsubbia@codeaurora.org>
Current wakeup time is surpassing next vsync and not being used.
This change will use mdp transfer time calculated by dsi to compute
line time in command mode. In video mode, fps will be used to compute
the line time. This line time will be used with current interface
line count to calculate time until the next vsync.
Change-Id: I0b6fc396711ade95ecf95755a907280309af223e
Signed-off-by: Thomas Dedinsky <tdedinsk@codeaurora.org>
Add a QoS vote on CPU receiving display interrupt. QoS vote
will prevent that CPU from going into low power mode avoiding
possible interrupt latency. Using irq notifier, display will
receive notification when display IRQ has switched CPUs and
will adjust the vote accordingly. The vote is also removed and
requested whenever display IRQ is enabled or disabled.
Change-Id: I94b4501896b4b20b37deaca90d6b5ff883d56621
Signed-off-by: Samantha Tran <samtran@codeaurora.org>
Signed-off-by: Lei Chen <chenlei@codeaurora.org>
Add stub functions for msm_hdcp module in order to prevent
linker issues when CONFIG_HDCP_QSEECOM is not defined, marked
as not disabled or defined as module. Furthermore, a Kbuild
entry for the msm_hdcp.h file so that it is exported.
Change-Id: I0f102bf4c9722d95b897facdab94d83e32f7d29f
Signed-off-by: Tatenda Chipeperekwa <tatendac@codeaurora.org>
Return EINVAL upon early exit/abort of authentication and
reset the authentication state.
Change-Id: I4862bbe55301eabef2a83849a551eb948f73569b
Signed-off-by: Rajat Gupta <rajatgu@codeaurora.org>
Signed-off-by: Tatenda Chipeperekwa <tatendac@codeaurora.org>
Get the register bus AB/IB vote values for each supported mode
from the device node to allow flexibility in adjusting these
settings for various different targets.
Change-Id: I258320d4847accfa8043f5f9fc4ccc791c16dddd
Signed-off-by: Steve Cohen <cohens@codeaurora.org>
If DP is running in mst mode, DP host should not power down during
unprepare call as aux need keep alive to handle further hot-plug
sideband message. Unless it is a PM suspend scenario where it is
required to deinit the host.
Change-Id: I208894e1cbc75e727044c196194b0a4e3936921e
Signed-off-by: Xiaowen Wu <wxiaowen@codeaurora.org>
Signed-off-by: Sankeerth Billakanti <sbillaka@codeaurora.org>
Signed-off-by: Tatenda Chipeperekwa <tatendac@codeaurora.org>
During suspend, there might be a chance that lib auth work is queued
but not yet started. So during pm cycle it might start execution
before host_init which can lead to noc error while accessing dp_aux
registers. To prevent that set abort flag to abort lib auth work and
set interrupts before host_deinit.
Change-Id: Ie2c3ac9b0846644d3c2b37f410c341659b030c16
Signed-off-by: Rajat Gupta <rajatgu@codeaurora.org>
Signed-off-by: Tatenda Chipeperekwa <tatendac@codeaurora.org>
Ensure host_init is executed when the DP display driver is resuming
from a video session teardown. The host_deinit is executed when DP
video session teardown is initiated by the userspace while DP cable
is connected. If the DP display is disconnected from dongle while
the video session is in teardown, the host_init is not executed
when the session is restored. All subsequent display connections
will fail because the core clocks are not on and aux abort is not
reset.
This change will ensure host_init is executed whenever the
host_deinit is executed during DP video session teardown by userspace.
Change-Id: If1ae3eb731a96bd929cd023733c098b513436a1c
Signed-off-by: Sankeerth Billakanti <sbillaka@codeaurora.org>
Signed-off-by: Tatenda Chipeperekwa <tatendac@codeaurora.org>
The hpd notification is skipped in connect_work if there is an
attention_work pending. So, the notification has to be sent in
attention_work.
Some dongles issue multiple attention events with LINK_STATUS_UPDATED
while the connect_work is in progress. So, once the link training
is successfully completed the LINK_STATUS_UPDATED attention event is
considered handled and the attention_work scheduled to execute after
the connect_work will return early without handling the
hpd_notification cases.
This change will ensure the hpd_notification is sent from
attention_work in such cases.
Change-Id: I5ef6781354b80842d2a6f44360cde25ee6d2b0b7
Signed-off-by: Sankeerth Billakanti <sbillaka@codeaurora.org>
Signed-off-by: Tatenda Chipeperekwa <tatendac@codeaurora.org>
