[ Upstream commit 1adff542d67a2ed1120955cb219bfff8a9c53f59 ]
The panic notifier infrastructure executes registered callbacks when
a panic event happens - such callbacks are executed in atomic context,
with interrupts and preemption disabled in the running CPU and all other
CPUs disabled. That said, mutexes in such context are not a good idea.
This patch replaces a regular mutex with a mutex_trylock safer approach;
given the nature of the mutex used in the driver, it should be pretty
uncommon being unable to acquire such mutex in the panic path, hence
no functional change should be observed (and if it is, that would be
likely a deadlock with the regular mutex).
Fixes: 2227b7c746 ("coresight: add support for CPU debug module")
Cc: Leo Yan <leo.yan@linaro.org>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Mike Leach <mike.leach@linaro.org>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Guilherme G. Piccoli <gpiccoli@igalia.com>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Link: https://lore.kernel.org/r/20220427224924.592546-10-gpiccoli@igalia.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0a7ff843d507ce2cca2c3b7e169ee56e28133530 ]
The base baud value reported is supposed to be the highest baud rate
that can be set for a serial port. The SiFive FU740-C000 SOC's on-chip
UART supports baud rates of up to 1/16 of the input clock rate, which is
the bus clock `tlclk'[1], often at 130MHz in the case of the HiFive
Unmatched board.
However the sifive UART driver reports a fixed value of 115200 instead:
10010000.serial: ttySIF0 at MMIO 0x10010000 (irq = 1, base_baud = 115200) is a SiFive UART v0
10011000.serial: ttySIF1 at MMIO 0x10011000 (irq = 2, base_baud = 115200) is a SiFive UART v0
even though we already support setting higher baud rates, e.g.:
$ tty
/dev/ttySIF1
$ stty speed
230400
The baud base value is computed by the serial core by dividing the UART
clock recorded in `struct uart_port' by 16, which is also the minimum
value of the clock divider supported, so correct the baud base value
reported by setting the UART clock recorded to the input clock rate
rather than 115200:
10010000.serial: ttySIF0 at MMIO 0x10010000 (irq = 1, base_baud = 8125000) is a SiFive UART v0
10011000.serial: ttySIF1 at MMIO 0x10011000 (irq = 2, base_baud = 8125000) is a SiFive UART v0
References:
[1] "SiFive FU740-C000 Manual", v1p3, SiFive, Inc., August 13, 2021,
Section 16.9 "Baud Rate Divisor Register (div)", pp.143-144
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Fixes: 1f1496a923b6 ("riscv: Fix sifive serial driver")
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2204291656280.9383@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5e73b2d9867998278479ccc065a8a8227a5513ef ]
Make sure to disable the pipe clock also if ufs-reset deassertion fails
during power on.
Note that the ufs-reset is asserted in qcom_qmp_phy_com_exit().
Fixes: c9b589791f ("phy: qcom: Utilize UFS reset controller")
Cc: Evan Green <evgreen@chromium.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20220502133130.4125-2-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 59d6f72f6f9c92fec8757d9e29527da828e9281f ]
irq_of_parse_and_map() returns 0 on failure, so this should not be
passed further as error return code.
Fixes: 1a358d350664 ("rpmsg: qcom_smd: Fix irq_of_parse_and_map() return value")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220423093932.32136-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5a7a184b11c6910f47600ff5cbbee34168f701a8 ]
Small adjustment the scale calibration value for the sc2731,
use new name sc2731_[big|small]_scale_graph_calib, and remove
the origin [big|small]_scale_graph_calib struct for unused.
Fixes: 8ba0dbfd07 (iio: adc: sc27xx: Add ADC scale calibration)
Signed-off-by: Cixi Geng <cixi.geng1@unisoc.com>
Link: https://lore.kernel.org/r/20220419142458.884933-4-gengcixi@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d345b23200bcdbd2bd3582213d738c258b77718f ]
wait_for_completion_timeout() returns unsigned long not long.
it returns 0 if timed out, and positive if completed.
The check for <= 0 is ambiguous and should be == 0 here
indicating timeout which is the only error case
Fixes: e813dde6f8 ("iio: stmpe-adc: Use wait_for_completion_timeout")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Reviewed-by: Philippe Schenker <philippe.schenker@toradex.com>
Link: https://lore.kernel.org/r/20220412065150.14486-1-linmq006@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5a0793ac66ac0e254d292f129a4d6c526f9f2aff ]
The bug is here:
pmem->vaddr = NULL;
The list iterator 'pmem' will point to a bogus position containing
HEAD if the list is empty or no element is found. This case must
be checked before any use of the iterator, otherwise it will
lead to a invalid memory access.
To fix this bug, just gen_pool_free/set NULL/list_del() and return
when found, otherwise list_del HEAD and return;
Fixes: 7ca5ce8965 ("firmware: add Intel Stratix10 service layer driver")
Signed-off-by: Xiaomeng Tong <xiam0nd.tong@gmail.com>
Link: https://lore.kernel.org/r/20220414035609.2239-1-xiam0nd.tong@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a03e2ddab8e735e2cc315609b297b300e9cc60d2 ]
If the device is already in a runtime PM enabled state
pm_runtime_get_sync() will return 1, so a test for negative
value should be used to check for errors.
Fixes: 8eed00b237 ("usb: dwc3: pci: Runtime resume child device from wq")
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Link: https://lore.kernel.org/r/20220422062652.10575-1-zhengyongjun3@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5e3b07ca5cc78cd4a987e78446849e41288d87cb ]
The hardware only supports periods <= 1.6 ms and if a bigger period is
requested it is clamped to 1.6 ms. In this case duty_cycle might be bigger
than 1.6 ms and then the duty cycle register is written with a value
bigger than LP3943_MAX_DUTY. So clamp duty_cycle accordingly.
Fixes: af66b3c093 ("pwm: Add LP3943 PWM driver")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7079b3483a17be2cfba64cbd4feb1b7ae07f1ea7 ]
If device_register() fails, device_unregister() should not be called
because it will free some resources that are not allocated.
put_device() should be used instead.
Fixes: 308ee87a2f ("staging: fieldbus: anybus-s: support HMS Anybus-S bus")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/5401a519608d6e1a4e7435c20f4f20b0c5c36c23.1650610082.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 424bef51fa530389b0b9008c9e144e40c10e8458 ]
The device_node pointer is returned by of_parse_phandle() with refcount
incremented. We should use of_node_put() on it when done.
Fixes: 8934d3e4d0 ("usb: musb: omap2430: Don't use omap_get_control_dev()")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Link: https://lore.kernel.org/r/20220309111033.24487-1-linmq006@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b92ffb1eddd9a66a90defc556dcbf65a43c196c7 ]
The function rio_karam_init() should return -ENOMEM instead of
value 0 (USB_STOR_TRANSPORT_GOOD) when allocation fails.
Similarly, it should return -EIO when rio_karma_send_command() fails.
Fixes: dfe0d3ba20 ("USB Storage: add rio karma eject support")
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Lin Ma <linma@zju.edu.cn>
Link: https://lore.kernel.org/r/20220412144359.28447-1-linma@zju.edu.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d088fabace2ca337b275d1d4b36db4fe7771e44f ]
The function documentation of usb_set_configuration says that its
callers should hold the device lock. This lock is held for all
callsites except tweak_set_configuration_cmd. The code path can be
executed for example when attaching a remote USB device.
The solution is to surround the call by the device lock.
This bug was found using my experimental own-developed static analysis
tool, which reported the missing lock on v5.17.2. I manually verified
this bug report by doing code review as well. I runtime checked that
the required lock is not held. I compiled and runtime tested this on
x86_64 with a USB mouse. After applying this patch, my analyser no
longer reports this potential bug.
Fixes: 2c8c981589 ("staging: usbip: let client choose device configuration")
Reviewed-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Niels Dossche <dossche.niels@gmail.com>
Link: https://lore.kernel.org/r/20220412165055.257113-1-dossche.niels@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9ec4cbf1cc55d126759051acfe328d489c5d6e60 ]
usb_get_dev() is called in stub_device_alloc(). When stub_probe() fails
after that, usb_put_dev() needs to be called to release the reference.
Fix this by moving usb_put_dev() to sdev_free error path handling.
Find this by code review.
Fixes: 3ff6744575 ("usbip: fix error handling in stub_probe()")
Reviewed-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Hangyu Hua <hbh25y@gmail.com>
Link: https://lore.kernel.org/r/20220412020257.9767-1-hbh25y@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f398e0aa325c61fa20903833a5b534ecb8e6e418 ]
Now fsl_lpuart driver use both of_alias_get_id() and ida_simple_get() in
.probe(), which has the potential bug. For example, when remove the
lpuart7 alias in dts, of_alias_get_id() will return error, then call
ida_simple_get() to allocate the id 0 for lpuart7, this may confilct
with the lpuart4 which has alias 0.
aliases {
...
serial0 = &lpuart4;
serial1 = &lpuart5;
serial2 = &lpuart6;
serial3 = &lpuart7;
}
So remove the ida_simple_get() in .probe(), return an error directly
when calling of_alias_get_id() fails, which is consistent with other
uart drivers behavior.
Fixes: 3bc3206e1c ("serial: fsl_lpuart: Remove the alias node dependence")
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20220321112211.8895-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 507b05063d1b7a1fcb9f7d7c47586fc4f3508f98 ]
In goldfish_tty_probe(), the port initialized through tty_port_init()
should be destroyed in error paths.In goldfish_tty_remove(), qtty->port
also should be destroyed or else might leak resources.
Fix the above by calling tty_port_destroy().
Fixes: 666b7793d4 ("goldfish: tty driver")
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Wang Weiyang <wangweiyang2@huawei.com>
Link: https://lore.kernel.org/r/20220328115844.86032-1-wangweiyang2@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fe78ccf79b0e29fd6d8dc2e2c3b0dbeda4ce3ad8 ]
The 24 bits data is stored in 32 bits in BE. There
is no need to shift it. This confuses user-space apps.
Fixes: b3af341bbd ("iio: adc: Add ad7124 support")
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Link: https://lore.kernel.org/r/20220322105029.86389-2-alexandru.tachici@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 84ef256550196bc06e6849a34224c998b45bd557 ]
If the list does not exit early then data == NULL and 'module' does not
point to a valid list element.
Using 'module' in such a case is not valid and was therefore removed.
Fixes: 6dd67645f2 ("greybus: audio: Use single codec driver registration")
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Vaibhav Agarwal <vaibhav.sr@gmail.com>
Reviewed-by: Mark Greer <mgreer@animalcreek.com>
Signed-off-by: Jakob Koschel <jakobkoschel@gmail.com>
Link: https://lore.kernel.org/r/20220321123626.3068639-1-jakobkoschel@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3928cf08334ed895a31458cbebd8d4ec6d84c080 ]
When the MIPS_ALCHEMY board selection is MIPS_XXS1500 instead of
MIPS_DB1XXX, the PCMCIA driver 'db1xxx_ss' has build errors due
to missing DB1XXX symbols. The PCMCIA driver should be restricted
to MIPS_DB1XXX instead of MIPS_ALCHEMY to fix this build error.
ERROR: modpost: "bcsr_read" [drivers/pcmcia/db1xxx_ss.ko] undefined!
ERROR: modpost: "bcsr_mod" [drivers/pcmcia/db1xxx_ss.ko] undefined!
Fixes: 42a4f17dc3 ("MIPS: Alchemy: remove SOC_AU1X00 in favor of MIPS_ALCHEMY")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Kees Cook <keescook@chromium.org>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: linux-mips@vger.kernel.org
Acked-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 40f567bbb3b0639d2ec7d1c6ad4b1b018f80cf19 upstream.
The function kzalloc() in detached_dev_do_request() can fail, so its
return value should be checked.
Fixes: bc082a55d2 ("bcache: fix inaccurate io state for detached bcache devices")
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Coly Li <colyli@suse.de>
Link: https://lore.kernel.org/r/20220527152818.27545-4-colyli@suse.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 22b106e5355d6e7a9c3b5cb5ed4ef22ae585ea94 upstream.
Commit d92c370a16cb ("block: really clone the block cgroup in
bio_clone_blkg_association") changed bio_clone_blkg_association() to
just clone bio->bi_blkg reference from source to destination bio. This
is however wrong if the source and destination bios are against
different block devices because struct blkcg_gq is different for each
bdev-blkcg pair. This will result in IOs being accounted (and throttled
as a result) multiple times against the same device (src bdev) while
throttling of the other device (dst bdev) is ignored. In case of BFQ the
inconsistency can even result in crashes in bfq_bic_update_cgroup().
Fix the problem by looking up correct blkcg_gq for the cloned bio.
Reported-by: Logan Gunthorpe <logang@deltatee.com>
Reported-and-tested-by: Donald Buczek <buczek@molgen.mpg.de>
Fixes: d92c370a16cb ("block: really clone the block cgroup in bio_clone_blkg_association")
CC: stable@vger.kernel.org
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/20220602081242.7731-1-jack@suse.cz
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 075a53b78b815301f8d3dd1ee2cd99554e34f0dd upstream.
Bios queued into BFQ IO scheduler can be associated with a cgroup that
was already offlined. This may then cause insertion of this bfq_group
into a service tree. But this bfq_group will get freed as soon as last
bio associated with it is completed leading to use after free issues for
service tree users. Fix the problem by making sure we always operate on
online bfq_group. If the bfq_group associated with the bio is not
online, we pick the first online parent.
CC: stable@vger.kernel.org
Fixes: e21b7a0b98 ("block, bfq: add full hierarchical scheduling and cgroups support")
Tested-by: "yukuai (C)" <yukuai3@huawei.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20220401102752.8599-9-jack@suse.cz
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4e54a2493e582361adc3bfbf06c7d50d19d18837 upstream.
BFQ usage of __bio_blkcg() is a relict from the past. Furthermore if bio
would not be associated with any blkcg, the usage of __bio_blkcg() in
BFQ is prone to races with the task being migrated between cgroups as
__bio_blkcg() calls at different places could return different blkcgs.
Convert BFQ to the new situation where bio->bi_blkg is initialized in
bio_set_dev() and thus practically always valid. This allows us to save
blkcg_gq lookup and noticeably simplify the code.
CC: stable@vger.kernel.org
Fixes: 0fe061b9f0 ("blkcg: fix ref count issue with bio_blkcg() using task_css")
Tested-by: "yukuai (C)" <yukuai3@huawei.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20220401102752.8599-8-jack@suse.cz
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5f550ede5edf846ecc0067be1ba80514e6fe7f8e upstream.
We call bfq_init_rq() from request merging functions where requests we
get should have already gone through bfq_init_rq() during insert and
anyway we want to do anything only if the request is already tracked by
BFQ. So replace calls to bfq_init_rq() with RQ_BFQQ() instead to simply
skip requests untracked by BFQ. We move bfq_init_rq() call in
bfq_insert_request() a bit earlier to cover request merging and thus
can transfer FIFO position in case of a merge.
CC: stable@vger.kernel.org
Tested-by: "yukuai (C)" <yukuai3@huawei.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20220401102752.8599-6-jack@suse.cz
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fc84e1f941b91221092da5b3102ec82da24c5673 upstream.
In bfq_insert_request() we unlock bfqd->lock only to call
trace_block_rq_insert() and then lock bfqd->lock again. This is really
pointless since tracing is disabled if we really care about performance
and even if the tracepoint is enabled, it is a quick call.
CC: stable@vger.kernel.org
Tested-by: "yukuai (C)" <yukuai3@huawei.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20220401102752.8599-5-jack@suse.cz
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c1cee4ab36acef271be9101590756ed0c0c374d9 upstream.
It can happen that the parent of a bfqq changes between the moment we
decide two queues are worth to merge (and set bic->stable_merge_bfqq)
and the moment bfq_setup_merge() is called. This can happen e.g. because
the process submitted IO for a different cgroup and thus bfqq got
reparented. It can even happen that the bfqq we are merging with has
parent cgroup that is already offline and going to be destroyed in which
case the merge can lead to use-after-free issues such as:
BUG: KASAN: use-after-free in __bfq_deactivate_entity+0x9cb/0xa50
Read of size 8 at addr ffff88800693c0c0 by task runc:[2:INIT]/10544
CPU: 0 PID: 10544 Comm: runc:[2:INIT] Tainted: G E 5.15.2-0.g5fb85fd-default #1 openSUSE Tumbleweed (unreleased) f1f3b891c72369aebecd2e43e4641a6358867c70
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.14.0-0-g155821a-rebuilt.opensuse.org 04/01/2014
Call Trace:
<IRQ>
dump_stack_lvl+0x46/0x5a
print_address_description.constprop.0+0x1f/0x140
? __bfq_deactivate_entity+0x9cb/0xa50
kasan_report.cold+0x7f/0x11b
? __bfq_deactivate_entity+0x9cb/0xa50
__bfq_deactivate_entity+0x9cb/0xa50
? update_curr+0x32f/0x5d0
bfq_deactivate_entity+0xa0/0x1d0
bfq_del_bfqq_busy+0x28a/0x420
? resched_curr+0x116/0x1d0
? bfq_requeue_bfqq+0x70/0x70
? check_preempt_wakeup+0x52b/0xbc0
__bfq_bfqq_expire+0x1a2/0x270
bfq_bfqq_expire+0xd16/0x2160
? try_to_wake_up+0x4ee/0x1260
? bfq_end_wr_async_queues+0xe0/0xe0
? _raw_write_unlock_bh+0x60/0x60
? _raw_spin_lock_irq+0x81/0xe0
bfq_idle_slice_timer+0x109/0x280
? bfq_dispatch_request+0x4870/0x4870
__hrtimer_run_queues+0x37d/0x700
? enqueue_hrtimer+0x1b0/0x1b0
? kvm_clock_get_cycles+0xd/0x10
? ktime_get_update_offsets_now+0x6f/0x280
hrtimer_interrupt+0x2c8/0x740
Fix the problem by checking that the parent of the two bfqqs we are
merging in bfq_setup_merge() is the same.
Link: https://lore.kernel.org/linux-block/20211125172809.GC19572@quack2.suse.cz/
CC: stable@vger.kernel.org
Fixes: 430a67f9d616 ("block, bfq: merge bursts of newly-created queues")
Tested-by: "yukuai (C)" <yukuai3@huawei.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20220401102752.8599-2-jack@suse.cz
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 424c3781dd1cb401857585331eaaa425a13f2429 upstream.
Remove unsupported forcing of `cpu_has_fpu' to 1, which makes the `nofpu'
kernel parameter non-functional, and also causes a link error:
ld: arch/mips/kernel/traps.o: in function `trap_init':
./arch/mips/include/asm/msa.h:(.init.text+0x348): undefined reference to `handle_fpe'
ld: ./arch/mips/include/asm/msa.h:(.init.text+0x354): undefined reference to `handle_fpe'
ld: ./arch/mips/include/asm/msa.h:(.init.text+0x360): undefined reference to `handle_fpe'
where the CONFIG_MIPS_FP_SUPPORT configuration option has been disabled.
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Reported-by: Stephen Zhang <starzhangzsd@gmail.com>
Fixes: 0ebb2f4159 ("MIPS: IP27: Update/restructure CPU overrides")
Cc: stable@vger.kernel.org # v4.2+
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2f917af777011c88e977b9b9a5d00b280d3a59ce upstream.
Current rxe_requester() doesn't generate a completion when processing an
unsupported/invalid opcode. If rxe driver doesn't support a new opcode
(e.g. RDMA Atomic Write) and RDMA library supports it, an application
using the new opcode can reproduce this issue. Fix the issue by calling
"goto err;".
Fixes: 8700e3e7c4 ("Soft RoCE driver")
Link: https://lore.kernel.org/r/20220410113513.27537-1-yangx.jy@fujitsu.com
Signed-off-by: Xiao Yang <yangx.jy@fujitsu.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 587f17018a2c6c414e41a312b002faaef60cf423 upstream.
This allows C code to make use of compilers with support for output
variables along the fallthrough path via preprocessor define:
CONFIG_CC_HAS_ASM_GOTO_OUTPUT
[ This is not used anywhere yet, and currently released compilers don't
support this yet, but it's coming, and I have some local experimental
patches to take advantage of it when it does - Linus ]
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4d2900f20edfe541f75756a00deeb2ffe7c66bc1 upstream.
Make sure to release the lane reset controller in case of a late probe
error (e.g. probe deferral).
Note that due to the reset controller being defined in devicetree in
"lane" child nodes, devm_reset_control_get_exclusive() cannot be used
directly.
Fixes: e78f3d15e1 ("phy: qcom-qmp: new qmp phy driver for qcom-chipsets")
Cc: stable@vger.kernel.org # 4.12
Cc: Vivek Gautam <vivek.gautam@codeaurora.org>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220427063243.32576-3-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8a177a36da6c54c98b8685d4f914cb3637d53c0d upstream.
iolatency needs to track the number of inflight IOs per cgroup. As this
tracking can be expensive, it is disabled when no cgroup has iolatency
configured for the device. To ensure that the inflight counters stay
balanced, iolatency_set_limit() freezes the request_queue while manipulating
the enabled counter, which ensures that no IO is in flight and thus all
counters are zero.
Unfortunately, iolatency_set_limit() isn't the only place where the enabled
counter is manipulated. iolatency_pd_offline() can also dec the counter and
trigger disabling. As this disabling happens without freezing the q, this
can easily happen while some IOs are in flight and thus leak the counts.
This can be easily demonstrated by turning on iolatency on an one empty
cgroup while IOs are in flight in other cgroups and then removing the
cgroup. Note that iolatency shouldn't have been enabled elsewhere in the
system to ensure that removing the cgroup disables iolatency for the whole
device.
The following keeps flipping on and off iolatency on sda:
echo +io > /sys/fs/cgroup/cgroup.subtree_control
while true; do
mkdir -p /sys/fs/cgroup/test
echo '8:0 target=100000' > /sys/fs/cgroup/test/io.latency
sleep 1
rmdir /sys/fs/cgroup/test
sleep 1
done
and there's concurrent fio generating direct rand reads:
fio --name test --filename=/dev/sda --direct=1 --rw=randread \
--runtime=600 --time_based --iodepth=256 --numjobs=4 --bs=4k
while monitoring with the following drgn script:
while True:
for css in css_for_each_descendant_pre(prog['blkcg_root'].css.address_of_()):
for pos in hlist_for_each(container_of(css, 'struct blkcg', 'css').blkg_list):
blkg = container_of(pos, 'struct blkcg_gq', 'blkcg_node')
pd = blkg.pd[prog['blkcg_policy_iolatency'].plid]
if pd.value_() == 0:
continue
iolat = container_of(pd, 'struct iolatency_grp', 'pd')
inflight = iolat.rq_wait.inflight.counter.value_()
if inflight:
print(f'inflight={inflight} {disk_name(blkg.q.disk).decode("utf-8")} '
f'{cgroup_path(css.cgroup).decode("utf-8")}')
time.sleep(1)
The monitoring output looks like the following:
inflight=1 sda /user.slice
inflight=1 sda /user.slice
...
inflight=14 sda /user.slice
inflight=13 sda /user.slice
inflight=17 sda /user.slice
inflight=15 sda /user.slice
inflight=18 sda /user.slice
inflight=17 sda /user.slice
inflight=20 sda /user.slice
inflight=19 sda /user.slice <- fio stopped, inflight stuck at 19
inflight=19 sda /user.slice
inflight=19 sda /user.slice
If a cgroup with stuck inflight ends up getting throttled, the throttled IOs
will never get issued as there's no completion event to wake it up leading
to an indefinite hang.
This patch fixes the bug by unifying enable handling into a work item which
is automatically kicked off from iolatency_set_min_lat_nsec() which is
called from both iolatency_set_limit() and iolatency_pd_offline() paths.
Punting to a work item is necessary as iolatency_pd_offline() is called
under spinlocks while freezing a request_queue requires a sleepable context.
This also simplifies the code reducing LOC sans the comments and avoids the
unnecessary freezes which were happening whenever a cgroup's latency target
is newly set or cleared.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Josef Bacik <josef@toxicpanda.com>
Cc: Liu Bo <bo.liu@linux.alibaba.com>
Fixes: 8c772a9bfc ("blk-iolatency: fix IO hang due to negative inflight counter")
Cc: stable@vger.kernel.org # v5.0+
Link: https://lore.kernel.org/r/Yn9ScX6Nx2qIiQQi@slm.duckdns.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3a21c3ac93aff7b4522b152399df8f6a041df56d upstream.
update documentation to correctly state the interrupt-cells to be 2.
Cc: stable@vger.kernel.org
Fixes: 4fd9bbc6e0 ("drivers/gpio: Altera soft IP GPIO driver devicetree binding")
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 627f01eab93d8671d4e4afee9b148f9998d20e7c upstream.
One of the changes in Sphinx 5.0.0 [1] says [sic]:
5.0.0 final
- #10474: language does not accept None as it value.
The default value of language becomes to 'en' now.
[1]: https://www.sphinx-doc.org/en/master/changes.html#release-5-0-0-released-may-30-2022
It results in a new warning from Sphinx 5.0.0 [sic]:
WARNING: Invalid configuration value found: 'language = None'.
Update your configuration to a valid langauge code. Falling
back to 'en' (English).
Silence the warning by using 'en'.
It works with all the Sphinx versions required for building
kernel documentation (1.7.9 or later).
Signed-off-by: Akira Yokosawa <akiyks@gmail.com>
Link: https://lore.kernel.org/r/bd0c2ddc-2401-03cb-4526-79ca664e1cbe@gmail.com
Cc: stable@vger.kernel.org
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2672a4bff6c03a20d5ae460a091f67ee782c3eff upstream.
From inspection I found a couple of GPIO lookups that are
listed with device "gpio-pxa", but actually have a number
from a different gpio controller.
Try to rectify that here, with a guess of what the actual
device name is.
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: stable@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bdef417d84536715145f6dc9cc3275c46f26295a upstream.
The bug is here:
return crtc;
The list iterator value 'crtc' will *always* be set and non-NULL by
list_for_each_entry(), so it is incorrect to assume that the iterator
value will be NULL if the list is empty or no element is found.
To fix the bug, return 'crtc' when found, otherwise return NULL.
Cc: stable@vger.kernel.org
fixes: 89c78134cc ("gma500: Add Poulsbo support")
Signed-off-by: Xiaomeng Tong <xiam0nd.tong@gmail.com>
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220327052028.2013-1-xiam0nd.tong@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8b917cbe38e9b0d002492477a9fc2bfee2412ce4 upstream.
The bug is here:
if (!encoder) {
The list iterator value 'encoder' will *always* be set and non-NULL
by list_for_each_entry(), so it is incorrect to assume that the
iterator value will be NULL if the list is empty or no element
is found.
To fix the bug, use a new variable 'iter' as the list iterator,
while use the original variable 'encoder' as a dedicated pointer
to point to the found element.
Cc: stable@vger.kernel.org
Fixes: ec9eab097a ("drm/tilcdc: Add drm bridge support for attaching drm bridge drivers")
Signed-off-by: Xiaomeng Tong <xiam0nd.tong@gmail.com>
Reviewed-by: Jyri Sarha <jyri.sarha@iki.fi>
Tested-by: Jyri Sarha <jyri.sarha@iki.fi>
Signed-off-by: Jyri Sarha <jyri.sarha@iki.fi>
Link: https://patchwork.freedesktop.org/patch/msgid/20220327061516.5076-1-xiam0nd.tong@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d9f3af4fbb1d955bbaf872d9e76502f6e3e803cb upstream.
When x_char is to be sent, the TX path overwrites whatever is in the
circular buffer at offset 0 with x_char and sends it using
pch_uart_hal_write(). I don't understand how this was supposed to work
if xmit->buf[0] already contained some character. It must have been
lost.
Remove this whole pop_tx_x() concept and do the work directly in the
callers. (Without printing anything using dev_dbg().)
Cc: <stable@vger.kernel.org>
Fixes: 3c6a483275 (Serial: EG20T: add PCH_UART driver)
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220503080808.28332-1-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 54a6f29522da3c914da30e50721dedf51046449a upstream.
If the previous list_for_each_entry_continue_rcu() don't exit early
(no goto hit inside the loop), the iterator 'cvif' after the loop
will be a bogus pointer to an invalid structure object containing
the HEAD (&ar->vif_list). As a result, the use of 'cvif' after that
will lead to a invalid memory access (i.e., 'cvif->id': the invalid
pointer dereference when return back to/after the callsite in the
carl9170_update_beacon()).
The original intention should have been to return the valid 'cvif'
when found in list, NULL otherwise. So just return NULL when no
entry found, to fix this bug.
Cc: stable@vger.kernel.org
Fixes: 1f1d9654e1 ("carl9170: refactor carl9170_update_beacon")
Signed-off-by: Xiaomeng Tong <xiam0nd.tong@gmail.com>
Acked-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220328122820.1004-1-xiam0nd.tong@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4213ff556740bb45e2d9ff0f50d056c4e7dd0921 upstream.
The driver has a custom put function for "DSP Voice Wake Up" which does
not generate event notifications on change, instead returning 0. Since we
already exit early in the case that there is no change this can be fixed
by unconditionally returning 1 at the end of the function.
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220428162444.3883147-1-broonie@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 746285cf81dc19502ab238249d75f5990bd2d231 upstream.
Using not existing queues can panic the kernel with rtl8180/rtl8185 cards.
Ignore the skb priority for those cards, they only have one tx queue. Pierre
Asselin (pa@panix.com) reported the kernel crash in the Gentoo forum:
https://forums.gentoo.org/viewtopic-t-1147832-postdays-0-postorder-asc-start-25.html
He also confirmed that this patch fixes the issue. In summary this happened:
After updating wpa_supplicant from 2.9 to 2.10 the kernel crashed with a
"divide error: 0000" when connecting to an AP. Control port tx now tries to
use IEEE80211_AC_VO for the priority, which wpa_supplicants starts to use in
2.10.
Since only the rtl8187se part of the driver supports QoS, the priority
of the skb is set to IEEE80211_AC_BE (2) by mac80211 for rtl8180/rtl8185
cards.
rtl8180 is then unconditionally reading out the priority and finally crashes on
drivers/net/wireless/realtek/rtl818x/rtl8180/dev.c line 544 without this
patch:
idx = (ring->idx + skb_queue_len(&ring->queue)) % ring->entries
"ring->entries" is zero for rtl8180/rtl8185 cards, tx_ring[2] never got
initialized.
Cc: stable@vger.kernel.org
Reported-by: pa@panix.com
Tested-by: pa@panix.com
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220422145228.7567-1-alexander@wetzel-home.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 48381273f8734d28ef56a5bdf1966dd8530111bc upstream.
The routine huge_pmd_unshare() is passed a pointer to an address
associated with an area which may be unshared. If unshare is successful
this address is updated to 'optimize' callers iterating over huge page
addresses. For the optimization to work correctly, address should be
updated to the last huge page in the unmapped/unshared area. However, in
the common case where the passed address is PUD_SIZE aligned, the address
is incorrectly updated to the address of the preceding huge page. That
wastes CPU cycles as the unmapped/unshared range is scanned twice.
Link: https://lkml.kernel.org/r/20220524205003.126184-1-mike.kravetz@oracle.com
Fixes: 39dde65c99 ("shared page table for hugetlb page")
Signed-off-by: Mike Kravetz <mike.kravetz@oracle.com>
Acked-by: Muchun Song <songmuchun@bytedance.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 37462a920392cb86541650a6f4121155f11f1199 upstream.
With gcc version 12.0.1 20220401 (Red Hat 12.0.1-0), building with
defconfig results in the following compilation error:
| CC mm/swapfile.o
| mm/swapfile.c: In function `setup_swap_info':
| mm/swapfile.c:2291:47: error: array subscript -1 is below array bounds
| of `struct plist_node[]' [-Werror=array-bounds]
| 2291 | p->avail_lists[i].prio = 1;
| | ~~~~~~~~~~~~~~^~~
| In file included from mm/swapfile.c:16:
| ./include/linux/swap.h:292:27: note: while referencing `avail_lists'
| 292 | struct plist_node avail_lists[]; /*
| | ^~~~~~~~~~~
This is due to the compiler detecting that the mask in
node_states[__state] could theoretically be zero, which would lead to
first_node() returning -1 through find_first_bit.
I believe that the warning/error is legitimate. I first tried adding a
test to check that the node mask is not emtpy, since a similar test exists
in the case where MAX_NUMNODES == 1.
However, adding the if statement causes other warnings to appear in
for_each_cpu_node_but, because it introduces a dangling else ambiguity.
And unfortunately, GCC is not smart enough to detect that the added test
makes the case where (node) == -1 impossible, so it still complains with
the same message.
This is why I settled on replacing that with a harmless, but relatively
useless (node) >= 0 test. Based on the warning for the dangling else, I
also decided to fix the case where MAX_NUMNODES == 1 by moving the
condition inside the for loop. It will still only be tested once. This
ensures that the meaning of an else following for_each_node_mask or
derivatives would not silently have a different meaning depending on the
configuration.
Link: https://lkml.kernel.org/r/20220414150855.2407137-3-dinechin@redhat.com
Signed-off-by: Christophe de Dinechin <christophe@dinechin.org>
Signed-off-by: Christophe de Dinechin <dinechin@redhat.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Ben Segall <bsegall@google.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Dietmar Eggemann <dietmar.eggemann@arm.com>
Cc: Vincent Guittot <vincent.guittot@linaro.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Daniel Bristot de Oliveira <bristot@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Zhen Lei <thunder.leizhen@huawei.com>
Cc: Juri Lelli <juri.lelli@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8b9ad480bd1dd25f4ff4854af5685fa334a2f57a upstream.
The bug is here:
if (!iommu || iommu->dev->of_node != spec->np) {
The list iterator value 'iommu' will *always* be set and non-NULL by
list_for_each_entry(), so it is incorrect to assume that the iterator
value will be NULL if the list is empty or no element is found (in fact,
it will point to a invalid structure object containing HEAD).
To fix the bug, use a new value 'iter' as the list iterator, while use
the old value 'iommu' as a dedicated variable to point to the found one,
and remove the unneeded check for 'iommu->dev->of_node != spec->np'
outside the loop.
Cc: stable@vger.kernel.org
Fixes: f78ebca8ff ("iommu/msm: Add support for generic master bindings")
Signed-off-by: Xiaomeng Tong <xiam0nd.tong@gmail.com>
Link: https://lore.kernel.org/r/20220501132823.12714-1-xiam0nd.tong@gmail.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2a4a62a14be1947fa945c5c11ebf67326381a568 upstream.
syscall_stub_data() expects the data_count parameter to be the number of
longs, not bytes.
==================================================================
BUG: KASAN: stack-out-of-bounds in syscall_stub_data+0x70/0xe0
Read of size 128 at addr 000000006411f6f0 by task swapper/1
CPU: 0 PID: 1 Comm: swapper Not tainted 5.18.0+ #18
Call Trace:
show_stack.cold+0x166/0x2a7
__dump_stack+0x3a/0x43
dump_stack_lvl+0x1f/0x27
print_report.cold+0xdb/0xf81
kasan_report+0x119/0x1f0
kasan_check_range+0x3a3/0x440
memcpy+0x52/0x140
syscall_stub_data+0x70/0xe0
write_ldt_entry+0xac/0x190
init_new_ldt+0x515/0x960
init_new_context+0x2c4/0x4d0
mm_init.constprop.0+0x5ed/0x760
mm_alloc+0x118/0x170
0x60033f48
do_one_initcall+0x1d7/0x860
0x60003e7b
kernel_init+0x6e/0x3d4
new_thread_handler+0x1e7/0x2c0
The buggy address belongs to stack of task swapper/1
and is located at offset 64 in frame:
init_new_ldt+0x0/0x960
This frame has 2 objects:
[32, 40) 'addr'
[64, 80) 'desc'
==================================================================
Fixes: 858259cf7d ("uml: maintain own LDT entries")
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Cc: stable@vger.kernel.org
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
