Send QCA_WLAN_VENDOR_ATTR_TWT_STATS_STATUS attribute in
the driver TWT get stats NL response.
Change-Id: I7c447a8d2841f3bb0143f9ac6f957b1f78fa1e21
CRs-Fixed: 2923086
If in SAP peer keep on connecting and disconnecting without
completing the EAPOL (e.g. due to wrong password), scan logic will
assume that EAPOL is in progress for long time and assert.
To fix this false alarm reset scan reject params on peer connect
and disconnect.
Change-Id: I067b5be39504651ffe4e29e1cc927ad0bc3a06c0
CRs-Fixed: 2928817
psoc_cfg is pointing to the address of a structure variable,
which will never be NULL.
To address this remove the NULL check.
Change-Id: I12f539ce2feace550c403ffc996fa315994470a7
CRs-Fixed: 2911862
In case of Non-DBS HW, don't allow channel to switch
to DFS channel or 160 Mhz BW in 5 Ghz, if STA is not
connected.
This is done because in Non-DBS HW, Monitoring mode
is disabled as sta_sap_scc_on_dfs_chnl is forced to
1.
Change-Id: Ie30a38a6c5155ca2b6f11f602fb51a43ca2e323e
CRs-Fixed: 2916799
Currently latency detection timer timeout and threshold values are
used as 2 and 1.9 seconds respectively. After going through few
issues, 2seconds found to be too aggressive and hence increasing
these values to 4 and 3.9 seconds respectively.
Change-Id: Ie9314b517a7a8e47460effc86e5b3fb939dcbb33
CRs-Fixed: 2921474
Driver report beacon/probe rsp frame in wlan_hdd_inform_bss_frame
to kernel. "boottime_ns" field needs be filled by "scansystimensec"
in nanosecond, so assign "boottime_ns" (NS) from scan entry to
bss_description instead of "scan_entry_time" (MS).
Change-Id: Id22f119f41f8cf60a8aadc9e04c4f18424c88413
CRs-Fixed: 2870827
Currently, active NDP sessions are tracked on the platforms
where NAN concurrency handling is supported by host through policy
mgr. Roaming is disabled when an active NDP session is present and
re-enabled when the last NDP session is teardown. But this tracking
is not supported on legacy platforms(which don't advertise either
WMI_SERVICE_NDI_DBS_SUPPORT or WMI_SERVICE_NAN_DISABLE_SUPPORT) as
policy mgr based tracking is not available.
So, disable roaming when the first NDP connection happens and
re-enable when the last peer is departed from HDD APIs in such
legacy platforms.
Change-Id: I6309af12eab9222dc34a79566f7830b7763826de
CRs-Fixed: 2846541
Currently in the WoW design of Moselle, EXT GRP IRQs are
enabled before sending SMP2P power save exit message is
sent to the FW. Because of this, any pending IRQs in the
GIC will immediately fire and could race with the SMP2P
power save exit logic. Any access to the registers done
before power save exit would result in system errors.
Enable the EXT GRP IRQs after sending power save exit
command will fix the problem.
Change-Id: I16f580279b5aa24861ab5111b9c13db3e38063f4
CRs-Fixed: 2925554
For PMF connection, when host gets assoc response fail with reason
"try again later" host runs PMF comeback timer to send assoc request
on pmf timer expiry. While PMF timer is running, if host gets
deauth/disassoc frame then host performs deauth/disassoc. As part
part of deauth/disassoc host changes lim mlm states to WT_DEL_BSS/
WT_DEL_STA and after moving vdev to down state host processes
DEL_BSS/DEL_STA response in LIM. At this stage expected lim mlm
state is WT_DEL_BSS/WT_DEL_STA but if the pmf timer expires the
pmf timer callback function changes lim mlm states to mlm states
stored in comeback timer info struct without checking present lim
mlm states.
Thus while processing DEL_BSS/DEL_STA response, host fails to get
PE session from vdev ID and lim mlm state WT_DEL_BSS/WT_DEL_STA.
And disconnect indication to sme fails. To fix this, host stops
pmf comeback timer while processing deauth/disassoc and change
lim mlm state after checking present lim mlm state.
Change-Id: If0094fcdb8254cb4271b5c46b4d42531dc9bc516
CRs-Fixed: 2925184
When the country code is updated, there is logic to check if a restart
of the adapter is needed. In this logic, there is a call to see if the
home channel is disabled. Sometimes, the home channel is 0 since it
has not been set yet, causing extra debug prints. To avoid this, ensure
the home channel is set before calling other APIs.
Change-Id: I58021f7f703761450c73a524c5acb51ddc7ad5ef
CRs-fixed: 2923754
In some case assos req/res length can be less than their respective
fixed fields due to which they get assigned to negative value
but as they are unsigned variable these req/res lengths gets convert
to large positive values. So during page memory allocation for these
lengths, page memory allocation failure happens.
To address the above issue add checks for both assoc req/res lenghts
before calculating the value for them.
Change-Id: Iff404e72420b27bc2a467a25fe530f135ee97c91
CRs-Fixed: 2903644
Enable DUMP_REO_QUEUE_INFO_IN_DDR to send cache flush cmd
to REO using cmd: iwpriv wlan0 txrx_stats 34 0
Cache flush cmd will invalidate the h/w cache and ensure
that h/w writes to DDR.
In the cmd callback, the reo status tlvs are processed
and the vaddr of the reo queue desc is used to read the
queue information from DDR and dump it in the host driver logs.
Change-Id: I4521b777d13c490ac687f9ff673182262bc52f62
CRs-Fixed: 2899824
In QCA_NL80211_VENDOR_SUBCMD_SET_WIFI_CONFIGURATION cmd parameters,
If attribute QCA_WLAN_VENDOR_ATTR_CONFIG_RX_MPDU_AGGREGATION is missed,
should return 0 instead of failed.
Change-Id: I5e570b9237768800e06d839814919d058a5e1d1f
CRs-Fixed: 2926104
By default, the driver fills the roam scan scheme as none for
all the triggers in WMI_ROAM_ENABLE_DISABLE_TRIGGER_REASON_CMDID
but if the roam scan scheme bitmap is set for particular
trigger, then for the corresponding trigger the roam scan scheme
should be sent as ROAM_TRIGGER_SCAN_MODE_PARTIAL.
Send ROAM_TRIGGER_SCAN_MODE_PARTIAL if roam scan scheme bitmap is
provided.
Change-Id: I82f16f7c0e24be472c95278eb3085f7d2623b63a
CRs-Fixed: 2914142
Firmware rejects TWT setup request due to roaming
in progress and channel switch with reason code
WMI_ADD_TWT_STATUS_ROAM_IN_PROGRESS,
WMI_ADD_TWT_STATUS_CHAN_SW_IN_PROGRESS.
Add support to handle TWT setup with new reason code.
Change-Id: I07dffc4a9ef10886c202f7c15300458018a7b7b6
CRs-Fixed: 2908380
Currently, while fetching ipv4 list in_dev is get via
in_dev_get and ref count of in_dev is incremented but
after fetching ip list in_dev_put is not used. So,
ref count will not be zero and may lead to issue while
destorying in_dev.
Fix is to use in_dev_put to maintain ref count to free
in_dev during rmmod.
Change-Id: I20a73127bb41c807315dbcd18adc1fb4278aa6d3
CRs-Fixed: 2921256
Add support to reject TWT setup request if received when the below
mentioned concurrency scenario exists.
STA + SAP: SCC or MCC: Reject TWT setup
STA + P2P: SCC or MCC: Reject TWT setup
Change-Id: I5c4c2bcc032276a0b83b7a46a44dbf7933cda29f
CRs-Fixed: 2923726
The userspace doesn't expect TWT teardown or notify events after
roaming. So to clear the driver internal TWT context, for old
peer, call the mlme_init_twt_context() on roam synch complete.
Change-Id: If1e4fe2d79561885052caf8d5231d1c943f10c96
CRs-Fixed: 2912872
If firmware sends the TWT teardown due to concurrent session is
established, then the wait for notify flag is not set. So other
commands can be sent to firmware.
In case of TWT teardown due to concurrency, set the wait for
notify flag.
Change-Id: Ia1d5134e1c6d931f8c5ced1c011efb3489d343ad
CRs-Fixed: 2919799
If STA connection is in 11b mode and TDLS connect in HE, the
phymoe is not calculated properly.
Handle the HE mode in 11b network type as well.
Change-Id: I0ddafa0b4be8d6eab02c66be7c0f909c2d968918
CRs-Fixed: 2923182
check if runtime pm enabled in wlan_hdd_runtime_resume
and wlan_hdd_runtime_suspend.
Change-Id: I107f953d19ea6078d8bb8a59d51dcac6736ff914
CRs-Fixed: 2920169
Add support to reject the TWT setup request if there exists
another TWT session with different dialog id.
Change-Id: I59c0ba4279581bad14bec886d22c0ac65838ec17
CRs-Fixed: 2920494
Currently, mlme_twt_is_command_in_progress() function checks if the given
command is in progress or not. For inputs like WLAN_TWT_ANY, if this function
returns true then from the current logs, its not known which
active command in progress.
Hence for better debugging, enhance this function to return active command.
Change-Id: Ibc5c5babb042408b0e8988fe229d344ed98bfff3
CRs-Fixed: 2920494
HSP doesn't support TX_AGGREGATION_SIZE ini, need disable it to avoid
confusing.
Change-Id: I9e49ad5218f913f116cf4472f768f572740f14df
CRs-Fixed: 2918796
Currently if STA is connected to HT only AP and if BW change
due to OBSS scan the htSupportedChannelWidthSet is not updated
and thus TDLS peer which use htSupportedChannelWidthSet to get
BW may not consider the vdev BW for HT and thus peer's BW can
go beyond VDEV's BW.
Fix this by updating htSupportedChannelWidthSet on vdev restart
on HT BW change
Change-Id: I7253fd240206ec27eac3e2b1de8debf8705a8234
CRs-Fixed: 2920539
In the current implementation of the function
__wlan_hdd_cfg80211_set_wifi_test_config, if the status returned by
get_cfg API is not Success, it returns froms the function without
freeing the allocated memory. This causes a potential memory leak.
To avoid this, free the allocated memory properly.
Change-Id: I5f9ac5f2edc49ebad662f18dbe09893f8bee6459
CRs-Fixed: 2918850
The feature HIF_DETECTION_LATENCY_ENABLE is not applicable for all targets.
To avoid issues, enable this feature based on target.
Change-Id: Ia7bab02710ee2bbb9f487571ec98992ac338961f
CRs-Fixed: 2915968
Currently FW dbg log levels are configured for every vdev creation.
But this is pdev level configuration and doesn't required to configure
for every vdev. Because of this WMI commands are getting flooded.
To avoid this, configure FW debug log levels only for first vdev
creation.
Change-Id: Ie395c1a7b0756a08ad7948997531c6920d83ae0b
CRs-fixed: 2913901
In STA+SAP mode, disable pipes is not done as part of either
last client disconnection or SAP down. In the scenario where
APPS suspend does not get triggered, IPA pipes are not disabled
and on runtime suspend, PCIe link is suspended which would result
in a NOC error if IPA HW accesses wlan registers.
Fix is to avoid runtime suspend if there are any pending IPA
tx completions.
Change-Id: I190da658d233cb5d6c85846312ddc7a251f9f9d5
CRs-Fixed: 2918334
