The feature HIF_DETECTION_LATENCY_ENABLE is not applicable for all targets.
To avoid issues, enable this feature based on target.
Change-Id: Ia7bab02710ee2bbb9f487571ec98992ac338961f
CRs-Fixed: 2915968
Currently FW dbg log levels are configured for every vdev creation.
But this is pdev level configuration and doesn't required to configure
for every vdev. Because of this WMI commands are getting flooded.
To avoid this, configure FW debug log levels only for first vdev
creation.
Change-Id: Ie395c1a7b0756a08ad7948997531c6920d83ae0b
CRs-fixed: 2913901
In STA+SAP mode, disable pipes is not done as part of either
last client disconnection or SAP down. In the scenario where
APPS suspend does not get triggered, IPA pipes are not disabled
and on runtime suspend, PCIe link is suspended which would result
in a NOC error if IPA HW accesses wlan registers.
Fix is to avoid runtime suspend if there are any pending IPA
tx completions.
Change-Id: I190da658d233cb5d6c85846312ddc7a251f9f9d5
CRs-Fixed: 2918334
1. If the TWT setup parameter re-negotiation results in failure,
then host driver shall trigger TWT teardown for the
existing TWT session.
2. Upon receiving the TWT teardown confirmation from the firmware,
host driver shall cleanup TWT session, send teardown notification
to the user space and ready for next TWT setup command.
Change-Id: I553ae7de8d900a3dc12d563b781f9fefa36f8a0b
CRs-Fixed: 2916548
The operating class triplet was removed from country IE. Add the logic
to populate it back in.
Change-Id: Ia9a1489e04d832b650dbe203534f38980e7e1506
CRs-fixed: 2913363
Send igmp offload command to fw with disable flag
once host comes to resume state from suspended state.
Change-Id: Iec2c6830028bf13dd90ac0a842774a4a7138286c
CRs-Fixed: 2911248
offload igmp feature to fw in case of suspended state
to avoid high power consumption.
Change-Id: I05fbf23dc2836f8f5dc6e2f45b35bf2d30c39790
CRs-Fixed: 2907644
The current implementation of add-wlan-objs does not work correctly
with GNU Make 3.81 which is widely in use. So refine the function in a
manner that works with 3.81 as well as newer versions of Make.
Change-Id: Ic689367cccc16cf6ab23eeeb58665d84c5db3a26
CRs-Fixed: 2903606
Currently the tcp delack reset config is initiated,
unconditionally, when the bus bandwidth timer is stopped.
This leads to unnecessary tcpdelack settings even if
it has not been enabled.
Reset the tcp delack setting from bus bandwidth timer stop
only if tcp delack is enabled.
Change-Id: I492ed18e80703f64bb0340d781f64760d6da2004
CRs-Fixed: 2914604
Currently, the AP power mode is only updated during HE OP IE population.
This causes the country IE to use the incorrect TX powers since HE OP is
populated afterwards. Add a call to update the power mode whenever the
country changes.
Change-Id: I46641d12f1aed045dbe1becf4b96ff65c5746c5b
CRs-fixed: 2910774
Currently runtime resume is marked as success after kicking
HTC queues, due to this non PM marked WMI commands are not
sent out properly.
Fix this by marking runtime resume as success before kicking
HTC queues, since resume is set as success as part of HTC kick
queues WMI commands will be sent out properly.
Change-Id: I5e3f98cbc5888bdf83f760b055c9b706c18737ef
CRs-Fixed: 2899609
Fix the TPE IE population for SAP. The total power and PSD power
are interchanged in TPE populate API.
Also, fix the TPC power calculation logic STA in non-PSD case when
TPE IE is present.
Populate current AP power type for SAP as well.
Change-Id: I0fb9b9318d1b5a3e1c8071714b7e3f6129828c92
CRs-Fixed: 2910658
Set channel width when calling wlan_reg_set_channel_params_for_freq.
Also, in the case of 160MHz, mhz_freq_seg1 should be used instead of
mhz_freq_seg0 to get center frequency.
Send total eirp power to FW instead of psd power for PSD case as
part of WMI_VDEV_SET_TPC_POWER_CMDID.
Change-Id: Id37d2ca37c7ae1ac07df1444129801fcba37f219
CRs-fixed: 2906551
In scenario, when ROAM HO failure is piggybacked on WOW wake up,
the blm reject AP addition fails as mutex can't be acquired in
interrupt context. With this change, the reject bssid blm
addition will happen after changing context to scheduler thread.
Change-Id: I685501b7ea48e4461922a7a50fb39c52d4d607f3
CRs-Fixed: 2880712
For sap mode, beacon frame has country IE, but country info
fields have all bands channels information. Using band based
chanel list to populate country IE information.
Change-Id: I0be084b9b539d453e5386c6a25dd2d9daa5de21c
CRs-Fixed: 2819683
Replace request_firmware by firmware_request_nowarn to avoid warning
message when the file is not found and sysfs fallback mechanism is
enabled if direct filesystem lookup fails.
Change-Id: Ia182bcf990144ac12434253144e772f6a0780cfe
CRs-Fixed: 2912035
Since stop_modules can happen in parallel due to idle shutdown,
add additional checks whether the IPA deinit happened already
or in-progress, in ipa_register_ready_cb.
Change-Id: Icc1973be3e90d4231addcebab55e621d19c5789c
CRs-Fixed: 2903419
Add a CDS API to check if the driver state is module stop and
also register for QDF wrapper for the same.
Change-Id: I99fbdda593ca229ef8db956c609735ae6509d511
CRs-Fixed: 2912747
When the SRNG IRQs are disabled during suspend, it is
required to disable the interrupts and wait for interrupts
that are pending to complete. Adding a pld/pfrm API to disable
irq synchronously.
CRs-Fixed: 2908685
Change-Id: Ia1f17d54cbe08e8dc101c0ecc2ddee9275712659
adapter->dev is used for get ref, issue happens
1 adapter is used to dev hold in thread_1
2 adapter is removed in thread_2 for interface
delete, and adapter->dev is set to NULL in
hdd_uninit.
3 thread_1 use adapter->dev for dev_put, then
adapter->dev is invalid here.
As adapter->dev will be invalid only after dev_put,
so not set null adapter->dev in hdd_uninit in case
dev_put need it.
Change-Id: Id764a6ef15ef8fc4eae24a3f2428d8cec55716aa
CRs-Fixed: 2912285
Target side STA PS module will only stop when WMI_VDEV_STOP
received, and QoS-null frame is possible to be sent in
the window from DEAUTH TX to WMI_VDEV_STOP.
Disable STA power save before disconnecting process,
to avoid QoS-null in such window.
Change-Id: I3f33fc7ab81f70c22218cd3cc5a4ba934c6bccae
Currently, host exits the regulatory update critical section as soon
as hdd_regulatory_dyn_cbk finishes. However, there is some work that
is scheduled to send the updated scan channel list to FW, which needs
to go inside the critical section as well. Move the logic to exit the
critical section after host sends the channel list.
Change-Id: I01f82232bdd4d4b3403f46dee5278fc74d50b05a
CRs-fixed: 2905643
Currently,there is an issue in hdd_adapter_iterator(), as it
is iterate till (n-1)th adapter. Due to this, in STA+STA+P2P
scenario, driver allows wlan0 scan when P2P connection in
progress as hdd_is_connection_in_progress() only check for
STA mode and miss the P2P mode.
Iterate till nth adapter as a fix.
Change-Id: Ia6e49b3a8372634756e89032ee9d599583160479
CRs-Fixed: 2907307
Don't allow twt statistics or clear statistics command
if twt statistics or clear statistics is in_progress.
As a Fix, reject the new twt statistic or clear statistic
command till existing twt statistic or clear statistic
command completion.
Change-Id: I710a81ae3409f181689b2e4c9e9d4e583d4aadab
CRs-Fixed: 2870592
Currently, TWT setup is allowed after roaming even if
TWT notify from firmware is not received.
Block the TWT setup till notify event is received
from firmware.
Change-Id: Ia6ff8fe9e05f32ddf6dbdd608d9090b612237f26
CRs-Fixed: 2870610
