In case if TWT command (i.e setup, terminate, pause, resume,
nudge) comes from userspace and if the firmware is in below mode
1. scan in progress
2. roam in progress
3. CSA is in progress
4. any other error
then the command needs to be rejected in userspace context
Synchronize the TWT commands so that whenever command goes from
driver to firmware, then driver will receive ack event first
followed by respective event (i.e add dialog, delete dialog,
pause, resume, nudge) with below condition
1. If driver receives the ack event as successful then driver
waits for this ack event, respective event with status of the
TWT action frame over the air is expected.
2. If driver receives the ack event as failure then it will
reject the TWT command request in userspace context.
Change-Id: Ib68b89b74b5e44f28106884efd7412cee49f5bd8
CRs-Fixed: 2987978
Add 6Ghz band HE capabilities for TDLS setup request and
setup response frames.
Change-Id: I02e8da12acc6832ad39d7166961c1c6546c8ad49
CRs-Fixed: 2994066
Add TWT service bit capability support to check whether firmware
supports ack event or not. If firmware doesn't support ack event
then service bit capability will become 0 and whenever the TWT
command comes, host will not wait for ack event and sends command
in a legacy way
This support is mainly added to handle new host and old firmware
combination.
Change-Id: I556d8edf0b505b774d756d6d904dd445418837bf
CRs-Fixed: 2987966
Add policy mgr connection list validation such as duplication
entry error. Flush the drv log and pause the logging
if error happens so that the issue log can't be overwritten
in stress test.
Change-Id: I037863de0bc5ecb8118c5792b6d73c3e200dd5c6
CRs-Fixed: 2991983
Add gConfigBleScanCoexPolicy which can be used to
control performance of ble scan case.
’0’ to place more emphasis on BLE Scan results
‘1’ to place more emphasis on WLAN performance
Change-Id: I46c735d8695523d14f6372bc5e47d1d1f51589ae
CRs-Fixed: 2935051
In hdd_sap_twt_get_session_params(), check NULL value of
params variable before it's used.
Change-Id: I47e57cbe98d7a0ee7015ab628d665037bf0b9853
CRs-Fixed: 2989510
Currently, In Reassoc and fast reassoc command host
validates freq from secondary channel list that may
cause issue for some frequencies which may be valid
for sta but invalid for sap.
Fix is to validate freq from valid channel list
Change-Id: I1ee81212425f7b4f997568b4fd92153231e349e8
CRs-Fixed: 2991541
All msdu's which are received in single mpdu will have same 802.11
header. Hardware fills header of only first msdu. So copy the
first msdu's header to all msdu's which are received in single
msdu in packet capture mode.
Change-Id: I1c9fd55e571eda77be0ab0863e03cd61b848b842
CRs-Fixed: 2968770
Fill the Coding info and STBC in HE data field of radiotap
header for TX data packets in packet capture mode.
Change-Id: I173ce1846259ee9e94587e360256161f8147df08
CRs-Fixed: 2984436
Currently, if there is no twt session present as part
of the twt get_status query with dialog_id = 0, host
returns failure.
Add support to include the session state, wake_duartion
and wake_interval for TWT get_status command with dialog_id = 0.
Change-Id: Ie59310dc07c9954da96cee6568de856be8f67652
CRs-Fixed: 2989788
Handle A-EDCA based on STA-SAP concurrency. Also, update
RTS profile based on the concurrency such that:
1) For STA and SAP concurrency, send STA's AP EDCA
params to fw. Also, for SAP or P2P Go, update the
value in Broadcast EDCA params as well so that it
should be broadcasted to other stations connected
to that BSS. Also, update the RTS profile value to
0x11. It will let FW disable SIFS bursting and send
RTS for every frame.
2) For standalone STA (can even happen after SAP/P2P Go
disconnects), if the parameters are updated, reset
them to original parameters and send them to FW.
Also, update the RTS profile value to the value
it was set before.
3) For standalone SAP (can even happen after STA
disconnects), if the parameters are updated, reset
them to original parameters and send them to FW and
reset the Broadcast EDCA params as well so that it
should be broadcasted to other stations connected
to that BSS Also, update the RTS profile value to
which it was set before.
Change-Id: Idb2b04b1b0bddb51cea9c5665847d04817a90aca
CRs-Fixed: 2949484
Fils info is stored per vdev. In RSO scan mode command, in FILS
TLV, the next ERP sequence number to be used in the next FILS
connection is sent to firmware and is filled from the vdev fils
info. But after roam sych event is received, the erp sequence
number is not updated in the vdev fils info, causing FILS roaming
failure.
Update the fils erp sequence number to vdev fils info after
roaming.
Change-Id: Ibc624d9c4b0fc535c430881d3033169b002c8419
CRs-Fixed: 2988113
According to new user request, add channel frequency 5745,
5765, 5785, 5805 to SAP mandatory channel list.
Change-Id: Icf1c96c07514f65a229e00d4330eaf0af5daa4ab
CRs-Fixed: 2987664
Some times there is delay in update of channel freq in vdev
because of which M1 channel freq is zero during initial
connection.
Fill freq from msdu start from rx_pkt_tlv.
Change-Id: Ia0a8f61c9113fbe5bc3ad932dcb67111b86629af
CRs-Fixed: 2964512
The delay before vdev stop is a global config,
no need to set for each interface separately.
Change-Id: I5760cf083a6749bb82cc88635a947f1d18308dfe
CRs-Fixed: 2904748
Currently, host sends DS param to fw based on
channel number but channel number may be same
in case of 6G and 2G due to which IEs can be
included in case of 6G which is not required.
Fix is to send DS param based on freq to
avoid addition of IEs in case of 6G band.
Change-Id: Ib711731fda3cfb0117478e6b1e026f40639a7fbb
CRs-Fixed: 2942323
At present the pre CAC is done based on original SAP's BW,
but usually the original SAP is on 2G and BW <= 40Mhz. The
requirement from user is to have higher BW on 5G. Hence, select
higher BW supported by SAP phymode to do pre CAC and move 2G
SAP to 5G pre CAC channel when pre CAC done successfully.
Also set the default MAX bw pre CAC to 80Mhz based on current user
request.
Change-Id: I3115da8eb649238da50b223c2587db96125ec813
CRs-Fixed: 2984084
This reverts the change to do the memset of SW2TCL desc consumed by
HW to zero.
Change-Id: Ie56207cf483643f6e294df23f5445ca853a75d51
CRs-Fixed: 2984818
In wlansap_get_csa_chanwidth_from_phymode(), update the
channel width correctly incase when SAP starts on 2.4GHz
and channel switch happens on 5GHz channel with BW 80 MHz.
Currently host modify the BW according to the original BW
20MHz is incorrect, it should be changed to 80MHz.
Update the BW correctly, it should not be limited to orig BW.
Change-Id: I9baf89d89eeb6407c7cda931b332bced38cc2154
CRs-Fixed: 2974565
Station sends the BA and upgrades to the next possible BA window
size upon receiving all frames successfully from the current
window. Some IOT APs go out of sync from BA window size of the
station when AP fails to receive the BA sent from station. AP
transmits the frames again with previous window sequence number
and won't be ack'ed by station hardware as BA window has already
moved ahead. So, station deletes the upgraded BA and tries
to fallback.
Ideally, AP is supposed to consider the fact that "the previous
window transmission was successful when station upgrades to next
window size". But some APs take little longer time to
recover/upgrade to next window size. Don't delete the BA
immediately and have some tolerance(3 seconds) as the previous
negotiated BA just got deleted.
Change-Id: I6b277223f02dac521316cec20bd5d958785cc2e9
CRs-Fixed: 2970714
Add DP reason code support for sending DELBA request,
so protocol layer can make decisions for special cases.
Change-Id: I4eeba3513820a98a15682190e40a06ce178d9441
CRs-Fixed: 2983544
There is a time involved between the smmu fault initiated
and the eventual system panic. In this time there is a
possibility of the nbuf history being overwritten losing
the information on the nbuf which might has actually caused
the SMMU fault.
Set the ssmu state and dont track the nbuf's when the smmu
fault is detected.
Change-Id: Ia9f422861cbb7bde1b498d8a88967616be99bb6e
CRs-Fixed: 2960063
Trigger SSR if pe session already exist for vdev, i.e vdev is
not in init state during connect req.
Also Add SSR if roam command timeout.
Change-Id: I83be76215f5c4daca2429a2528f825baabed92e3
CRs-Fixed: 2982362
