eMMC device operating at 1.8 V can be run up to 100 MHz without SDCDC
(DLL) and with DLL above 100 MHz.
Change the existing pr_err condition to less than 100MHz.
Change-Id: Ia6575ddfd0e4dc57723226e3dff24ad485a1a2ea
Signed-off-by: Sarthak Garg <sartgarg@codeaurora.org>
When the kernel is compiled with the sparse static analysis tool
enabled, the following warnings are emitted:
drivers/soc/qcom//trace_secure_buffer.h:53:1: warning: incorrect type in
assignment (different base types)
drivers/soc/qcom//trace_secure_buffer.h:53:1: warning: incorrect type in
assignment (different base types)
drivers/soc/qcom//trace_secure_buffer.h:53:1: warning: invalid
assignment: +=
Fix this by converting the type of the addrs variable from phys_addr_t
to u64, since the value we read into it is of type__le64 will always be
64 bits, while phys_addr_t may not be. Also, use the correct accessors
when accessing variables of type __le64.
Change-Id: Ia7e2394f2dc501dbf80f9035e0177555449dcfd8
Signed-off-by: Isaac J. Manjarres <isaacm@codeaurora.org>
If refcount on mem entry is the last refcount, we will call
kgsl_mem_entry_destroy and detach it from process list. If
there is no refcount on the process private as well then we
will call kgsl_destroy_process_private to cleanup. During
cleanup, we will try to remove the same sysfs node which is
in use by the current thread and this situation will end up in
a deadlock.
To fix this problem, use a worker to put the refcount on mem
entry.
Change-Id: I69a77c4059489c95de2ca205701571daac4bdc8a
Signed-off-by: Pankaj Gupta <gpankaj@codeaurora.org>
We currently set best_parent_rate to the ideal frequency wanted by the
RCG. This doesn't always align to the exact frequency the parent can
provide. If they differ, then clk_calc_new_rates() will return the
parent as top, even if the rounded parent frequency isn't changing.
This causes clk_propagate_rate_change() to return before being called
for its children, which means children aren't notified of the
PRE_RATE_CHANGE events.
Set best_parent_rate to the rounded rate so that we don't unnecessarily
try to change the parent.
Change-Id: Ic976db7a13dfbc63cb66b032a45060565ca90b43
Signed-off-by: Mike Tipton <mdtipton@codeaurora.org>
Currently driver calculating stale delay based on baud rate during
stop_rx sequencer. When BT started with lower baud rate like 2400
this logic will add around 130msecs of extra delay during BT INIT.
This change will remove logic for stale delay calculation
based on baud rate and add constant delay of 10msec to
wait for stale interrupt during stop_rx_sequencer.
Change-Id: I566d79145ba887de71482642655b63c5bd640fc8
Signed-off-by: Chandana Kishori Chiluveru <cchiluve@codeaurora.org>
To handle install cnss2 as module, need set dms server state after
bus init.
Change-Id: Ie6ac374193057190a69cb8e98da1771657b00f2d
Signed-off-by: Will Huang <wilhuang@codeaurora.org>
This change is for general scheduler improvements.
Change-Id: Ib0ed25f0b83a6a7bbc0f600ef2a9351d578bffb5
Signed-off-by: Lingutla Chandrasekhar <clingutla@codeaurora.org>
To avoid overclocking issues observed on few parts,
use floor ops for SDCC clocks.
Change-Id: I0bdb6dd540a4885f0c39f25ed97b17035e31f510
Signed-off-by: Jagadeesh Kona <jkona@codeaurora.org>
FIFO_REAL_TIME_FILL_STATUS_MASK is different for haptics HW
version V3. Update it.
Change-Id: Ida8326d89678af34ae2c3a35164ae1a7ad5f6b7b
Signed-off-by: Kiran Gunda <kgunda@codeaurora.org>
Add ep details corresponding to
RMNET_CV2X tethering over eth.
Change-Id: I0285887470c950a73e61dd51bf673bbc650d40bb
Signed-off-by: Pooja Kumari <kumarip@codeaurora.org>
As per the latest ipcat gpio6 func2 should be
mapped to qup6. Changes are done to support the same.
Change-Id: I57bf30916a8b51eececdeefe21ac3729bc20d903
Signed-off-by: Swetha Chikkaboraiah <schikk@codeaurora.org>
"mapped" variable inside kgsl_mem_entry structure is not used anymore.
Remove this variable from kgsl_mem_entry structure.
Change-Id: I3ced1ae140e8ce91fdc4eac3276d3f5283823fd6
Signed-off-by: Kamal Agrawal <kamaagra@codeaurora.org>
The function pil_clear_segment should be called only
when S2 mapping is success. So update clear_fw_region
accordingly.
Change-Id: Ie5bcf5b322ce347b08a575d18b7de3226027af91
Signed-off-by: Swetha Chikkaboraiah <schikk@codeaurora.org>
Existing api msm_pcie_write_reg_field() calls find_next_bit()
and results in a KASAN out of bounds error for taking in
the first parameter by typecasting as unsigned long type.
To avoid the KASAN error use __ffs() instead.
Change-Id: I9e155248e1233bbcb04ac5e2d1d6d512b3fa5387
Signed-off-by: Siddartha Mohanadoss <smohanad@codeaurora.org>
Restoring CMDQ_SEND_STATUS_TRIGGER field after XO or hardware reset can
lead to CMD13 being send as soon as CQE is turned on which can lead to
below unnecessary warnings followed by register dumps.
[ 82.554113] mmc: sdhci_cmd_irq: Got command interrupt 0x00000001 even
though no command operation was in progress.
Unset that bit before restoring CMDQ_VENDOR_SPECIFIC_CFG register.
Change-Id: Id5961ecdd68b0d7cbc1c48c116f9e862a1dfc573
Signed-off-by: Sarthak Garg <sartgarg@codeaurora.org>
For low temperature (< -25 degrees) WLAN FW need to keep
delay between WLAN EN low and HIGH. Read WLAN_EN delay
set by "wlan_en_delay" sysfs file and send it through
Host Cap request. Increase MODE_ON and TARGET_CAP QMI request
timeout to WLAN_EN delay value to accommodate delay kept
in FW for WCN6750.
Change-Id: Ic52cc94183984200f4cc3d893756bf7abeddad6d
Signed-off-by: Naman Padhiar <npadhiar@codeaurora.org>
