In csr_nonscan_pending_ll_next/csr_nonscan_pending_ll_peek_head and
csr_nonscan_active_ll_peek_head all commands umac_cmd is mapped
to tSmeCmd. This can lead to invalid pointer access as umac_cmd
can be of different type and does not always map to tSmeCmd.
Thus return the cmds only with source WLAN_UMAC_COMP_MLME, which are
initiated by sme and has tSmeCmd mapped to umac_cmd.
Change-Id: I73e75ef5ea754f4ef548a1cb9b3de2d0e566adf6
CRs-Fixed: 2655838
If start bss fail in logs it indicate start BSS timeout, so
fix the logs to indicate proper logs.
Change-Id: Ie470550a1606a1cddd6577f0945386e8c1a5cc13
CRs-Fixed: 2655836
If the SAP is already in stopping state and wlansap_stop_bss is invoked
as a part of stop_adapter, it returns error which causes the
stop_adapter not to wait for the vdev to return to proper state.
To avoid this, return success in case of SAP_STOPPING for the event
eSAP_HDD_STOP_INFRA_BSS
Change-Id: I99a2cd0a1d12b8e43fb3e88b6889e1d651633283
CRs-Fixed: 2654042
nla_put fails when there is no sufficient buffer to put the
beacon IEs. Enhance the log to print available buffer length and
the beacon IEs length.
Change-Id: If6e37455f6fbe795b293f626ad9cbb24a9effcd0
CRs-Fixed: 2629807
Enable the build configuration for dp hang event to
enable the datapath hang event logging feature.
Change-Id: I8044f977e417a311a17e446cc6b71211d217ae4b
CRs-Fixed:
Update the hang data for the pessssion. For the pe module
update the various states which will give insight into the reason
for recovery.
Change-Id: I7e3f18bd8b18dd0d56c09d4a4ce38ce7c3677ecc
CRs-Fixed: 2651762
Remove ol recovery notifier to log ce info as the notifier
is added in hif layer.
Change-Id: Ia3b56f677d7207f7b650ee1060032c285fa946fe
CRs-Fixed: 2649143
If DUT connects to an AP in VHT mode with 40/80Mhz bandwidth in 5Ghz
band and then if user changes the country code(EC) where only 20Mhz
bandwidth present in 5ghz, then after association AP may ignore DUT's
support for only 20Mhz and keeps transmitting data in 40/80Mhz.
As DUT doesn't support these bandwidth, DUT doesn't ack the data
packets with higher received higher bandwidth. Thus DUT's RX throughout
degrades. This is an IOT issue where AP expects OMN IE with channel width
set to 20mhz . As DUT is not sending OMN IE low throughput issue is
observed
Hence host adds OMN ie in the association request only if the AP to
which DUT associates advertises OMN IE and DUT supports VHT.
Change-Id: Ie59323c4c7dc4e4abc332e7204768b6a560d22d1
CRs-Fixed: 2650234
Currently there is no provision to configure OCL mode in FW during
driver bootup.
To enable this configuration add a new INI configuration parameter
gOclCfg.
Change-Id: I87c9131f5395c394f745e0170f0d9b3d1571d030
CRs-Fixed: 2644312
In peer assoc the 40MHz flag is set if HT is enabled and bandwidth
is 40MHz which fails the 40MHz setting for 6GHz connection as HT
is not supported in 6GHz band.
Remove the HT check for 40MHz flag setting in peer assoc.
Change-Id: I2a34dd6fbbca50912952f532e8b485148bf3c3a2
CRs-Fixed: 2649524
Whenever a recovery is triggered in the hdd layer update the
various vdev data for hang event:
1) Vdev id
2) vdev opmode
3) vdev state and substate
if the reason for recovery is max scan failures update the last
scan reject, reason and the vdev id on which scan is rejected.
Change-Id: I84928e56bac1fe58e7eada0a0574b2f23124ae65
CRs-Fixed: 2651694
Update the hang data for the cds module, as part of the hang
data following information is filled:
1) Hang Event version
2) Wlan Driver version
3) Reason for recovery
Change-Id: Ie5a008d1f9512f8e83a1d099fe333b0d2ce90abb
CRs-Fixed: 2650848
htc hang event configuration has been added, enable
the build configration for the feature.
Change-Id: I5441f95288db46ca58ef44f4c825b9f4f7cf59ac
CRs-Fixed: 2651750
Destroy PM QOS spinlock after unregistering PM QOS notifier. Use
hif_pm_runtime_put() instead of hif_pm_runtime_put_noidle() so that
it can trigger a runtime PM suspend after usage count reaching 0.
Change-Id: I93949857636de6d9807fa2abceec818a8584c596
CRs-fixed: 2651516
Currently the expectation from the BLM is to flush
all the BSSIDs which are present in the blacklist
when the user does an explicit on-off, which is
meeting the expectation, but the FW does not flush
this info which leads to async between the two.
Fix is to send 0 blacklist BSSID to FW during
Wifi-off so that it also flushes the list.
Change-Id: I7a0629fefb12deaeec0b5eeea06169272621bf82
CRs-Fixed: 2647018
Add code to handle hang event data and length received
from platform driver through uevent.
Change-Id: Ie4acf55cd7d2e602ad10eedbdeed045acfd85f56
CRs-fixed: 2650831
Currently, wlan_hdd_cfg80211_convert_rxmgmt_flags set rxmgmt flags
based on RXMGMT_FLAG_EXTERNAL_AUTH & flag provided by lim.
For some action category like FST, RVS driver itself sets flag value as
RXMGMT_FLAG_NONE. In this case, wlan_hdd_cfg80211_convert_rxmgmt_flags
return -EINVAL and considers it as err.
Fix is to remove if check for wlan_hdd_cfg80211_convert_rxmgmt_flags
to avoid err print in case flag received is RXMGMT_FLAG_NONE.
Change-Id: I321ef05d0571a5b14793d36abfd327dfa97c70a5
CRs-Fixed: 2654080
In stop bss write to reo remap control registers happen
after pcie power collapse is enabled. As pcie power collapse
is enabled sometimes reo remap register write is not going
through. For sta + sap concurrency this is resulting in NOC
error when other sta interface connecting to AP after stop bss.
Disable autonomy or reo remap registers to sw host destination
rings happen as part of last sap client deregistration. In this
change deregister sap clients before stop bss.
Change-Id: Ic84a1d45b5b376ec8ad28a05246efc4252b390ab
CRs-fixed: 2643092
wmi hang event configuration has been added, enable
the build configration for the feature.
Change-Id: I8c7034d07f369f79191a2496e9000f83eecdba6e
CRs-Fixed: 2651741
In qdf new hang event notifier chain has been added, enable
the build configration for the feature.
Change-Id: I98e2701499133d208af863b401fc47fafec35226
CRs-Fixed: 2648449
In qdf new os specicfic notifier chain has been added, enable
the build configration for the feature.
Change-Id: Ic08b3ebc3b173839496428a27d0eb4d7a1633cb6
CRs-Fixed: 2648245
NDIs don't have any peers and there is no need to send/receive
any data frames on NDI as such. NDPs latched on to the NDI
have peers and they are registered as STA properly.
Change-Id: I545ab01c6c67febdeba39ab52c9e4263e1757002
CRs-Fixed: 2651435
As part of SSR, hdd stop adapter is called which in
turn calls undo acs which frees the sap channel lists.
Now if SAP was already on, and then SSR happens then this
channel list would be freed.
After SSR the SAP would again be restarted.
Now if the driver gets an LTE-coex event from the FW,
there would be no channel-list left in the ACS list, as
it would freed, so there would be no suitable channel
for SAP restart leading to SAP stuck on an unsafe
channel which impact LTE throughput.
Fix is to call undo acs as part of deinit adapter which
would ensure that interface down has happened.
Change-Id: I5bf7bfcc20ccc686792b6b1df5d42b03288f7766
CRs-Fixed: 2650261
In the API policy_mgr_checkn_update_hw_mode_single_mac_mode
the driver checks that if the bands are different, then go
for DBS and single mac mode is not required.
In the case of STA on 5ghz and SAP now coming up on 6ghz
the bands would be different but the hw mode needed
would be single MAC mode and not DBS, but according to the
check mentioned above the driver would still return and
the final hw mode would be stuck into DBS which would
lead to unnecessary power consumption because of the second
MAC being still swithched on having no vdev attached to it.
Fix is to check whether DBS is required and avoid the condition
mentioned above.
Change-Id: I91d91894dde1a3b84c22f9de59c83a5f0b727315
CRs-Fixed: 2651178
With the introduction of 6GHz channels, some of the channel
frequency checking code have to be refined to make sure
all non-2.4GHz channel frequencies are identified by
!WLAN_REG_IS_24GHZ_CH_FREQ().
Change the channel frequency identifying code within the
following functions according to the above guideline:
wlan_hdd_cfg80211_start_acs()
hdd_cfg80211_update_acs_config()
hdd_get_sap_operating_band()
hdd_update_acs_sap_config()
wlan_hdd_sap_p2p_11ac_overrides()
wlan_hdd_cfg80211_start_bss()
wma_send_pdev_set_pcl_cmd()
Change-Id: I6dfb8b4e43a7f632255fb89552490ce404874998
CRs-Fixed: 2648176
