Need to ensure that that the wakeup message gets processed
deterministically (before the return of hif_bus_suspend,
or after the message has woken up the apps.)
In another change, the driver will check for the wakeup message
after hif_bus_suspend completes and reject the suspend if it
has allready recieve the wakeup message. In conjunction with
this change the host will not be able to accidentally process
and discard the wakeup message.
Change-Id: I6d487a00dcfd40a665d3be03697f3a7cfc815203
CRs-Fixed: 1051968
Need to register the device as a wakeup source and configure
the corect interrupt as a wakeup source for the snoc bus.
Change-Id: I2afcd69a8308183e141d7560a225a3b48d0e9f55
CRs-Fixed: 1051968
Make O(1) checks for corruption and list state to rule out
suspicion of double free and memory corruption. Only traverse
the memory tracking list to differentiate between memory corruption
and freeing an untracked pointer.
Since we check for corruption before traversing the list, the qdf_mem_free
api may crash with a use after free signature before printing out the
double free error message.
Change-Id: I0862822a65634dc68d8146f44f0474b672b6fc0a
CRs-Fixed: 1049430
PLD is a interface between CLD and CNSS/ICNSS. It hides
CNSS/ICNSS APIs from CLD and provides a set of common APIs.
CLD modules should use these PLD APIs instead of calling
CNSS/ICNSS platform APIs.
Replace all CNSS/ICNSS APIs with PLD APIs in HIF.
CRs-Fixed: 1010692
Change-Id: I4018a4b7e08179f9c65a19fde61727228e876762
With Load once unload never architecture, the cds modules
will be opened/closed several times. As part of configuration
of modules bus id needs to passed. So, add a new member to save
the bus_id passed by the platform driver during the driver
intialization,
Change-Id: Ic580e03076e5e8c557dde1879e223606a14f79b8
CRs-Fixed: 1049224
Because the register values were not defined in the target defs table,
The values were defaulting to 0 or missing. The code to write to these
registers checks if they exist before trying to write to them. Without
these registers defined, the base addresses of the dma rings would be
truncated to 32 bits.
Change-Id: Iabb49df50c2452522b6da30154e4d7d7221e22ac
CRs-Fixed: 1049424
Q_TARGET_ACCESS return value check was incorrect.
Fixed to match usage in the rest of the driver.
Change-Id: I73631536c9670edcb5014f3e850985dfc6fc4d16
CRs-Fixed: 1046067
Compilation error occurs due to undefined struct when
WMI_INTERFACE_EVENT_LOGGING disabled.
Use void pointer as argument to wmi_mgmt_cmd_record() and cast as header
struct inside logging function to avoid casting as undeclared type.
Change-Id: I7d0922ee2009b235473febdbcbc3317e432a1386
CRs-Fixed: 1043597
WLAN suspend/resume feature has tight dependency on APPS platform
suspend/resume support. On new targets APPS suspend/resume is not
supported until target is feature complete. In absence of APPS
suspend/resume support testing WLAN offload features become
difficult. Add unit test framework to test WLAN suspend/resume
features using private IOCTL command by simulating APPS
suspend/resume behaviour.
Trigger WLAN suspend:
iwpriv wlan0 wlan_suspend 0 0
To resume WLAN run a ping test from access point side and very 1st
ping request unicast packet should trigger wake up.
If FW is not waking up APPS then use below command to do a manual
wake up:
Trigger WLAN resume:
iwpriv wlan0 wlan_resume 0 0
This framework is only for SNOC platform.
Change-Id: I177a0047f460aa2a305a9e4e46fbfaa94a81dced
CRs-Fixed: 1042205
HOST driver unload sequence does following
1) Kill WLAN tasklet
2) Disable CE interrupts
3) Flush WMI RX work
Hence its unncessory to acquire eventq_lock as no one
will be using the shared resource during wmi detach.
Change-Id: I5c549358aeefc460c794c35659915d3b966c7350
CRs-Fixed: 1021376
Propagation from qcacld-2.0 to qcacld-3.0
Adding WMI defs for pdev and peer GET_ANTDIV_STATUS_CMD,
ANTDIV_INFO_EVENT msgs.
Change-Id: Iad3c57f0b4e10e68c86cef175b8cadcfd9e7fe1e
CRs-fixed: 865207
qcacld-2.0 to qcacmn propagation.
oem data request len size should be of 4 byte instead of
1 byte.
Add changes to correct len size in wmi unified API.
Change-Id: I9b377420c50ff1160964f94be5eaa0072df0f63d
CRs-Fixed: 1013488
Fixing 32 bit compliation issues due to improper type
casting and shift operation.
CRs-Fixed: 1043823
Change-Id: I2c05a0c0940c5d65c40aefdc80dc2888fbe87be1
Propagation from qcacld-2.0 to qcacld-3.0
Add WMI command to set GPIO numbers that are used to wakeup host
and wakeup target.
Changes to disable dynamic bandwidth RTS.
Add swol_assist_enable field to WMI extwow_set_app_type1_params
cmd to enable IoT mode WMI enums for CCK and OFDM max tx rates.
Change-Id: I26873873d7a355c179babaa7cc56e187e9771c92
CRs-fixed: 865207
Fix the occupied channel list that is being passed from CSR to
WMA to WMI to firmware.There is a conversion happening in
WMA from channel number to frequency which is the root of the
issue.
Change-Id: I8a2f8c9d31897b38086df26ebd386ec59d0f3540
CRs-Fixed: 1039020
Propagation from qcacld-2.0 to qcacld-3.0
Add mcast filter set/delete command that can take multiple
filters in a list.
Fix HTT typos to make MACROS consistent with the field name.
Change-Id: I97ca72f102faecfc3d20409b0d4819a09968417c
CRs-fixed: 865207
Propagation from qcacld-2.0 to qcacld-3.0.
New WMI command for reorder queue setup/removal
Change-Id: I31ad0432a0d5f49eed55603ae7d9eeedbdd19876
CRs-Fixed: 865207
More detailed logging needed for mgmt frames
Add vdev_id, frame type, subtype, and channel to logs by defining wrapper
function around logging macro and calling it from send_mgmt_cmd_tlv
Change-Id: I0c8c26e3194d97be7d903f64c5c5909c2d4b9799
CRs-Fixed: 1011346
FW common files needs to be in sync with host and fw.
There are duplicate definition of target attach API when
latest copy of fw common files are used.
Remove duplicate definition of target attach from hif layer.
Change-Id: Ie4a80ba07bc3ec2d9d1466c32062c373c9759a94
CRs-Fixed: 1012542
Refer to runtime_pm_delay inside the config_info structure.
The member was moved inside a config_info structure to cleanup
hif_softc.
Change-Id: I45b54ef2323eb635bb110ece381d5c806a0a4627
CRs-Fixed: 1035562
