Remove qdf print from QDF_TRACE
Change physical address type to qdf_dma_addr_t
Add qdf API to get min of two numbers
Change-Id: Ie4e0a98d603e56e1bdaf3b8b7c099c7dad5b1bac
CRs-Fixed: 2016072
Introduce a new iwpriv command txrx_stats to
print host and firmware statistics for lithium
chipset
Change-Id: Ib048c64f903c7a97508f8b03bebe7f7c1d9e6c05
CRs-Fixed: 2017426
This change adds implementation for interfacing with LMAC for
southbound request to WMI and northbount events from WMI.
Change-Id: Ia027ec704d99ef586b89bfadce4f174c3bcf8c17
CRs-Fixed: 2003488
The functions process the RADAR pulses. If Radar is found then it sends
RADAR found notification, marks the channel as RADAR and add the RADAR
infected channel to NOL.
Change-Id: Ic53d6408bf32c24826b7ef97eee3657adac8ef90
CRs-Fixed: 2001106
NOL stands for non-occupancy list. After RADAR has been detected in a
particular channel, the channel cannot be used for a period of 30 minutes,
which is called the non-occupancy. The NOL is basically a list of all the
channels on which RADAR has been detected. Each channel has a 30-minute
timer associated with it.
Change-Id: Ie823ef86a4109ff200c9bb2307711d17ff3f9876
CRs-Fixed: 2001106
Operation in a DFS channel requires CAC that adds additional
delay as well as loss of connection even when CSA is used. ETSI allows
pre-CAC, i.e. performing CAC at a convenient time and using that channel
later. Once Pre-CAC is done in a channel, it is no longer required to
perform a CAC in the channel before TX/RX as long as radar is not found
in it or we reset or restart the device.
Change-Id: Ic1896f7881c12606f1edc20c60cd4bb2ab63821c
CRs-Fixed: 2001106
Channel Availability Check (CAC) Time: The time a system shall
monitor a channel for the presence of RADAR prior to initiating
a communications link on that channel.
It is implemented using one-shot timer.
Change-Id: Iacf33681006cd8ee87e26fe63a852ff44a932e31
CRs-Fixed: 2001106
Whenever the hardware detects a RADAR PHY error, it generates an interrupt
and the MAC layer provides the RSSI value, Pulse width, Timestamp on the
collected data, and FFT data to Software.
There is an event queue associated with RADAR detection. The RSSI, pulse
width, and time stamp is stored in the queue by the interrupt handler.
There is a DFS timer task that reads the entries in the queue associated
with RADAR detection. It checks the time stamp, RSSI, and pulse width
value against the PRI, RSSI, and pulse width defined in the RADAR filter
table. If any entry of the table mactches then it announces RADAR is found.
Change-Id: I71bf88c77eb5baa4984bdc2181ca27008d641469
CRs-Fixed: 2001106
The main task of the Dynamic Frequency Selection (DFS) component is to
analyze RADAR pulses and declare RADAR detected if a filter match is
found. The DFS component also performs channel availability Check (CAC),
stores Non Occupancy List (NOL), and selects a random channel from a
list of available channels. This componentization of DFS code brings all
the scattered code into a single place, which makes it is easy to maintain
and also easy to move the component to a desired software layer with
minimal effort. Any DFS data structure and code must be accessed through
the public APIs provided in the DFS dispatcher.
This commit contains only Filtering part. Next and subsequent commits will
contain: Filter Tables, CAC, Zero CAC, NOL, RADAR event notification, and
DFS Dispatcher.
Change-Id: I2c21f7752545eb910c48ade630ceba74053cc019
CRs-Fixed: 2001106
Setup all TID queues during rx peer init
Add support to handle ADDBA HTT msg
Allow pkts to be fwd to stack even if peer isn't found
Change-Id: Icdfec2eeaa3e0ca62202ed278cd63209b8f79cb2
CRs-Fixed: 2016138
Incorrect arguments are being provided to qdf_mem_set
during wlan_global_lmac_if_close().
Add change to provide correct arguments.
Change-Id: I79b2a299a2766a1b8432b725e88c73883fba8700
CRs-Fixed: 2022370
Add command to set mapid for each VAP using:
iwpriv athX s_dscp_mapid N
Add command to change tid values in PDEV maps using:
iwpriv wifiX s_dscp_tid_map <MAP_ID> <TOS> <TID>
Change-Id: I510a40e71ecec5c453dd2dff1b13fd5ebedbe98a
CRs-Fixed: 1108452
Change it since WLAN_P2P_ENABLE easily confused with existed macro
WLAN_FEATURE_P2P
Change-Id: Ia27aae849da7a8f8921bff40168105ca16b993b7
CRs-Fixed: 2021996
Process the message WMI_REG_CHAN_LIST_CC_EVENTID. This message is used to
populate the master channel list.
Change-Id: I96d8f7ff5f71a35686ba990175c4a37995bfa6b2
CRs-Fixed 2002892
Register the regulatory component with obj mgr. Regulatory
component only needs to listen to psoc level messages.
Change-Id: I3d060d66cb7bac2912afb1301ef1960f8bd9c0ef
CRs-Fixed: 2002892
New regulatory database that is offload friendly. The
same database would be used in firmware also.
Change-Id: I4f8ee3555882fcc672d893ff544e119773dfd4c0
CRs-Fixed: 2002892
